Search Results

Search found 18160 results on 727 pages for 'jdk 7 feature complete'.

Page 544/727 | < Previous Page | 540 541 542 543 544 545 546 547 548 549 550 551  | Next Page >

  • How to resolve virtual disk degraded in Windows Server 2012

    - by harrydev
    I am using the new Storage Spaces feature in Windows Server 2012. I have the following disks: FriendlyName CanPool OperationalStatus HealthStatus Usage Size ------------ ------- ----------------- ------------ ----- ---- PhysicalDisk2 False OK Healthy Auto-Select 2.73 TB PhysicalDisk3 False OK Healthy Auto-Select 2.73 TB PhysicalDisk4 False OK Healthy Auto-Select 2.73 TB PhysicalDisk5 False OK Healthy Auto-Select 2.73 TB There is also a separate OS disk. The above disks are part of a single storage pool: FriendlyName OperationalStatus HealthStatus IsPrimordial IsReadOnly ------------ ----------------- ------------ ------------ ---------- Pool OK Healthy False False Within this storage pool some virtual disks are defined, see below: FriendlyName ResiliencySettingNa OperationalStatus HealthStatus IsManualAttach Size me ------------ ------------------- ----------------- ------------ -------------- ---- Docs Mirror OK Healthy False 500 GB Data Mirror Degraded Warning False 500 GB Work Mirror Degraded Warning False 2 TB Now the virtual disks are all running normal 2-way mirror, but two of the virtual disks are degraded. This is probably because one of the physical disks was offline for a short period of time. However, now the virtual disk cannot be repaired, even though, all physical disks are healthy. There is plenty of available space in the storage pool. This I cannot understand so I was hoping for some help, on how to resolve this? Below I have listed the full output from the Get-VirtualDisk CmdLet for the "Work" disk: ObjectId : {XXXXXXXX} PassThroughClass : PassThroughIds : PassThroughNamespace : PassThroughServer : UniqueId : XXXXXXXX Access : Read/Write AllocatedSize : 412316860416 DetachedReason : None FootprintOnPool : 824633720832 FriendlyName : Work HealthStatus : Warning Interleave : 262144 IsDeduplicationEnabled : False IsEnclosureAware : False IsManualAttach : False IsSnapshot : False LogicalSectorSize : 512 Name : NameFormat : NumberOfAvailableCopies : 0 NumberOfColumns : 2 NumberOfDataCopies : 2 OperationalStatus : Degraded OtherOperationalStatusDescription : OtherUsageDescription : Disk for data being worked on (not backed up) ParityLayout : PhysicalDiskRedundancy : 1 PhysicalSectorSize : 4096 ProvisioningType : Thin RequestNoSinglePointOfFailure : True ResiliencySettingName : Mirror Size : 2199023255552 UniqueIdFormat : Vendor Specific UniqueIdFormatDescription : Usage : Other PSComputerName :

    Read the article

  • Windows: disable remote access of local drive, even by domain admin

    - by Matt
    We have a network of Windows 7 PCs that are managed as part of a domain. What we want is for the domain admin to be unable to view the PC's local drive (C:) unless he is physically at the PC. In other words, no remote desktop and no ability to use UNC. In other words, the domain admin should not be allowed to put \\user_pc\c$ in Windows Explorer and see all the files on that computer, unless he is physically present at the PC itself. Edit: to clarify some of the questions/comments that have come up. Yes, I am an admin---but a complete Windows novice. And yes, for the sake of this and my similar questions, it is fair to assume that I am working for someone who is paranoid. I understand the arguments about this being a "social problem versus a technical problem", and "you should be able to trust your admins", etc. But this is the situation in which I find myself. I'm basically new to Windows system administration, but am tasked with creating an environment that is secure by the company owner's definition---and this definition is clearly very different from what most people expect. In short, I understand that this is an unusual request. But I'm hoping there is enough expertise in the ServerFault community to point me in the right direction.

    Read the article

  • How do I restore a Windows Server 2008 R2 bare metal backup to a Windows Server 2012 R2 Hyper-V instance?

    - by Michael J. Gray
    I have been trying to find a simple way to migrate a physical Windows Server 2008 R2 installation over to a virtual machine hosted on Windows Server 2012 R2 Datacenter Edition /w Hyper-V. I came across the bare metal backup feature on Windows Server 2008 R2 and assumed I would be able to easily back it up and simply restore it into a new virtual machine by booting the installation media and getting into the Windows recovery process. When I attempted this, Hyper-V got into a network based restore process, but I do not have a PXE server or anything like that and I would rather not set it up. I tried mounting the VHD produced in the bare metal backup, just to see if it would somehow work, but it of course did not and failed with an error related to an incorrect boot device. I checked the virtual machine's BIOS settings and everything looked fine. I did not expect this to work anyway, so I stopped working through this method any further. Is there a way to take my bare metal backup and restore it into a virtual machine without a PXE server or SCVMM? I am opening to using proprietary tools but since the last time I did this I used Norton Ghost, which is no longer supported, I figured I would try doing it with what is readily available.

    Read the article

  • Ubuntu 12.04/12.10 can't detect windows or any other partitions(Asus z77 UEFI BIOS)

    - by user971155
    I've recently completed tinkering my new pc(motherboard ASUS z77 with UEFI BIOS) and unfortunately not everything works quite well. After installing windows 7 ultimate on a single primary partition(SATA drive) I decided to allocate one more logical partition for additional needs. When I tried doing it with the manager - it said that it couldn't allocate requested size even though I certainly asked for much less than it was available. I thought that it might have been a windows issue and proceded to installing Ubuntu 12.10 x64. When the graphical interface loaded it showed me a message stating that it can't find any other operating system on the drive. When I used custom partioning option it showed me none of my current partions(including that with windows). However, when I boot with "Try Ubuntu" feature it does find them ! I find it weird though. Here's what the console present me with: ubuntu@ubuntu:~$ sudo os-prober /dev/sda1:Windows 7 (loader):Windows:chain ubuntu@ubuntu:~$ sudo fdisk -l Disk /dev/sda: 640.1 GB, 640135028736 bytes 255 heads, 63 sectors/track, 77825 cylinders, total 1250263728 sectors Units = sectors of 1 * 512 = 512 bytes Sector size (logical/physical): 512 bytes / 512 bytes I/O size (minimum/optimal): 512 bytes / 512 bytes Disk identifier: 0x00072b98 Device Boot Start End Blocks Id System /dev/sda1 * 2048 206847 102400 7 HPFS/NTFS/exFAT /dev/sda2 206848 100020223 49906688 7 HPFS/NTFS/exFAT /dev/sda3 100022270 1250263039 575120385 5 Extended /dev/sda4 566669312 1250263039 341796864 83 Linux I also tried creating partitions from disk utility which results in error: , Error creating partition: helper exited with exit code 1: In part_add_partition: device_file=/dev/sda, start=51211402240, size=1923000000, type=0x83 Entering MS-DOS parser (offset=0, size=640135028736) MSDOS_MAGIC found looking at part 0 (offset 1048576, size 104857600, type 0x07) new part entry looking at part 1 (offset 105906176, size 51104448512, type 0x07) new part entry looking at part 2 (offset 51211402240, size 588923274240, type 0x05) Entering MS-DOS extended parser (offset=51211402240, size=588923274240) readfrom = 51211402240 MSDOS_MAGIC found Exiting MS-DOS extended parser looking at part 3 (offset 290134687744, size 349999988736, type 0x83) new part entry Exiting MS-DOS parser MSDOS partition table detected containing partition table scheme = 1 got it Error: Can't have overlapping partitions. ped_disk_new() failed Here's what I get when I try to install the system i.stack.imgur.com/pjlb9.png, i.stack.imgur.com/g1lXN.png P.S. It's strange that I even can't create any more partitions neither with disk-utility nor with windows 7 native tools

    Read the article

  • How to organize deployment process in Chef-controlled environment?

    - by Alex
    I have a web Linux-based infrastructure which consists of 15 virtual machines and over 50 various services. It is fully controlled by Chef. Most of the services are developed internally. Basically the current deployment process is triggered by a shell script. A build system (a mix of Python and shell scripts) packages the services as .deb files and puts these packages into a repo. It runs apt-get update on all 15 nodes then because the standard Chef apt cookbook only runs apt-get once per day and we definitely do not want to run apt-get update unconditionally on each chef-client wake. The build system restarts chef-client daemons on all 15 nodes finally (we need this step because of pull Chef nature). The current process has a number of drawbacks we want to address. First off, it is asynchronous because the deployment script does not check chef-client logs after restart so we don't even know if the deployment was successful. It does not even wait for Chef clients to complete the cycle. Second, we definitely do not want to force chef-client restarts on all nodes because we usually deploy only a small number of packages. And third, I am not quite sure using chef-client for deployment is legitimate, probably we are just doing it wrong from the start. Please share your thoughts/experience.

    Read the article

  • How do I add a WMware ESXi Host to Microsoft Virtual Machine Manager?

    - by user63250
    I am trying to manage virtual machines running on a VMware ESXi host using Microsoft System Center Virtual Machine Manager. I was able to add the ESXi machine using the "Add VMware VirtualCenter server" option, but can't access any of the VMs on the datastore associated with this ESXi server. The datastore of the ESXi box is showing up with the correct name, but it won't let me see any of the VMs that have already been created; I get "There are no virtual machines on this host." Because I couldn't get any of the existing virtual machines to show up, I tried creating some new ones. When using VMM to connect to ESXi and create new VMs, I get the following error messages in the "rating explanation" section: The virtualization software on the selected host does not support virtual hard disks on an IDE bus. and The virtualization software on the host XXXXXX does not support the creation of dynamic virtual hard disk. Any ideas on why I can't manage existing machines and why I can't create new ones? The existing machines were created in vSphere. I should note that the ESXi server and the server running SCVMM are both on the same domain. I should also note that although the ESXi box has been added as a VirtualCetner server, when I try to add it through the "Add Host" option, I get an error message saying "Virtual Machine Manager cannot complete the VirtualCenter action on server EXSi because of the following error: The operation is not supported on the object."

    Read the article

  • Can two mocha for After Effects X-Spline Layers be merged ?

    - by George Profenza
    Hello, I'm new to mocha for After Effects, but like the auto tracking feature. There are a few markers I'm adding, but there's one which is giving me a bit of a headache. I'm tracking a circle that moves around a larger object, so it moves in front of it initially, then behind, being occluded by the larger object, then in front again. I tried to track the circle in the first part(when it's in front, before being occluded) and in the second part(when it's in front again, coming out on the other side of the large object) using a single X-Spline. The problem is the second part starts in a different location and I don't know how to 'move' the X-Spline to the new position and track from there, without affecting the previous keyframes. As a workaround I use two X-Spline Layers, export the data to .txt files, then manually merge the two files into a new one containing keyframes from both X-Spline Layers. Is there an easier way to do this (either merging two X-Spline Layer, or using a single X-Spline Layer that can move to a new location without affecting previous keyframes) ? Any suggestion would help.

    Read the article

  • Load Balancing Rails on Apache 2.x

    - by revgum
    My situation is that I need to proxy traffic to the root of my web server to port 81 for IIS, and then any traffic to a sub-directory needs to be directed to the rails app. my-server.com/ - needs to proxy to port 81 my-server.com/myapp - needs to point to the rails app This seems to be working alright for the rails application but the images, javascripts, and stylesheets are not actually working (proxied). I've tried to fiddle with the proxypass lines but it still doesn't work for me..can anyone help? Here's my complete VirtualHost portion of the config; LoadModule proxy_module modules/mod_proxy.so LoadModule proxy_http_module modules/mod_proxy_http.so ProxyRequests off <Proxy balancer://myapp_cluster> BalancerMember http://127.0.0.1:3001 BalancerMember http://127.0.0.1:3002 </Proxy> <VirtualHost *:80> DocumentRoot "c:\ruby\apps\myapp\public" <Directory /myapp > Options FollowSymLinks AllowOverride None </Directory> ProxyPass /myapp/images ! ProxyPass /myapp/stylesheets ! ProxyPass /myapp/javascripts ! ProxyPass /myapp/ balancer://myapp_cluster/ ProxyPassReverse /myapp/ balancer://myapp_cluster/ ProxyPreserveHost on ProxyPass / http://localhost:81/ ErrorLog "c:\ruby\apps\myapp\log\error.log" # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog "c:\ruby\apps\myapp\log\access.log" combined </VirtualHost>

    Read the article

  • 802.11g -> wired ethernet bridging not working

    - by Malachi
    Usually people want to go the other direction, but I want to take our relatively fast and stable house 802.11g signal and bridge it to ethernet. I have tried using an Airport Express (the b/g flavor) and my i7 MacBook pro, both to no avail. Word is that the b/g flavor of This flavor of Airport Express maxes at firmware 6.3 which doesn't support this kind of bridging properly. However, I expected my MacBook pro to do the job with its "Internet Sharing" feature. Alas, although my wired PC does sort of see it, it doesn't work out. Strangely, using DHCP the PC receives the same IP address as my MBP uses on the network. Less strangely, but still surprisingly, the wired ethernet port on my mac registers as the IP address of the gateway when queried with IFCONFIG. It sort of makes sense that the mac would "pretend" to be the gateway, but the whole thing just isn't working and seems configured wrong - but all the docs I see say basically "OS X Internet Sharing: click it and go". What do I do? Do i really have to buy more hardware, even though I have plenty of would-be candidates for bridging? Incidentally, the host router originating the 802.11g signal is a belkin 802.11g router, and is documented to support WDS.

    Read the article

  • mac gets stuck in a blue screen during boot

    - by user10826
    Hi, a macbook pro 2008 unibody, after restart gets stuck in a blue screen. I used the Leopard disk and I verified and repaired permissions, which seem to be a problem, because the assistant found some wrong files. After restart I got the same problem. After googling I reset PRAM and the other (I do not remember the name now). Same problem. I check that I can boot in safe mode, although it is a lot slower. So before anything I try to make a time machine backup, hoping that I can be done from safe mode. First question: If it works, is it possible to do a clean leopard install (I do not like Snow) and migrate all user accounts from the backup, although it was done in safe mode? Second question: I read about the feature "archive and install" from the leopard disc. Is it reliable? Because I am afraid of losing all data ... Third question: I think this boot stuck has to do with the load of some program or service. It would explain why the computer does boot on safe mode and not in the normal one. I would then like to check what the computer loads during boot, but in more detail that with the information provided from /system preferecens/account/start, because there I removed everything. Where can I find more advanced information? And, if I remove programs from the safe mode, will it be effective druing the normal boot? Thanks

    Read the article

  • Desktop PC does not power up on power button

    - by hIpPy
    When I press the power button on my desktop, it does not power up completely. Before I press the power button, I see lights on the motherboard. Everything is normal. On power button press, the fans on the cpu, graphics card and motherboard start to spin a little for a second or two and then they stop. No beeps during this process. It has been doing this for a while now but it used to start up after some trials. Once it starts up, I have NO issues at all like random shutdowns so it is not an issue with OS. Update: I left the desktop off for a few days and it started. I'm just guessing here but it seems as if the PSU (Antec TP2-550ATX) is dying out and does not have enough power now - just a guess. It's an old desktop assembled in 2005 but I have maintained it well. Update: I always keep the desktop running and I never shut it down. During updates or manual restarts, it powers up without issues. I wonder if this sheds lights on the issue. Any idea how I can narrow down the issue? ex: if I can find if the PSU is dying etc. I'd really like to fix the issue. Please help. Thanks. Below is the complete configuration. DFI LAN-Party UT NF4 Ultra-D 6/23 {6.70}, Evercool EC-VC-RE 41/47C, AMD Opteron 170 2.0GHz {1.3.2.16} 1.312V 36/41C, ThermalRight SI-120, Panaflo 120×38mm OCZ Platinum 2×1GB 200MHz 2.66V 3-3-2-7 1T XFX 7800GTX 256MB 475/1250MHz {91.31}, Zalman VF900 Cu led 41/56C WD Caviar 320GB 7200RPM 16MB SATA 3Gb/s Antec TP2-550ATX Antec P180 WinXP sp3 Logitech MX310 Razer Mantis Speed BenQ FP91G+ 19" LCD 8ms DVI Creative Audigy2 ZS {4.42} BenQ DW1640 Logitech z-5300e 5.1 280W Legend: Driver versions: {} User settings: [] Voltage: V Wattage: W Temperature: C (Celsius) min/max

    Read the article

  • running chkdsk /F on a large mounted NTFS image file gets BSOD (Windows Vista)

    - by Citizentools
    Using ddrescue, I've created ISO files from the C: and D: drives on my Windows XP laptop's harddisk (after the laptop stopped booting and chkdsk etc. wouldn't fix it). I was able to mount the 60 GB D.iso file use OSFmount, and successfully recreated the D: drive on another laptop. The C.iso image is more problematic. ddrescue left about 3mb unrecovered of 85 GB total, after multiple passes (no big worries about this) and I'm able to mount it with OSFmount on a Windows Vista laptop. However, when I run chkdsk /F /V on the mounted drive (which was mounted as H:), I consistently get a blue screen (BSOD). CHKDSK makes it through the first three passes, including index fixing and security descriptor fixes, without errors, but triggers a BSOD when it attempts to fix the volume records or bitmap If I attempt to fix the drive by clicking on Properties-Tools-Error checking-Check Now-Automatically fix file system errors, I get an alert box reading "WIndows was unable to complete the disk check." I'd try a tool other than OSFMount, but it's the only thing I've found so far that will mount large ISO files, and it has worked for me up to now in this process. [Update 2011-11-13 18:41 EST] Just ran the same process using the original Windows XP laptop, with a different internal drive, and chkdsk worked like a champ. So the question is still interesting, but decidedly less urgent.

    Read the article

  • New SSD, is the MBR broken? DISK BOOT FAILURE

    - by Shevek
    I've been running Windows 7 on a WD 500gb SATA single drive, single partition setup for some time with no issues. I've just installed a new Kingston V Series 64gb SSD and performed a clean install of Win7 to it, deleting the partitions on the 500gb and using that as a data drive. All was well for a few reboots but then I started to get "DISK BOOT FAILURE, INSERT SYSTEM DISK AND PRESS ENTER" messages. If I put the Win7 install DVD back in the drive it boots fine. Tried a clean install again, after replacing SATA cables and swapping SATA ports, with a complete partition wipe of both drives. Again, rebooted fine a few times then back with the "DISK BOOT FAILURE" error. Looked on the web and found some discussions about it so I then started from scratch again. This time I wiped the MBR on both drives using MBRWork, disconnected the 500gb and reinstalled to the SSD. Removed the install DVD and installed all the drivers which involved many reboots, all with no problem. To make sure I also did a few cold boots as well. Reconnected the 500gb, initialised, partitioned and formatted it. Copied data to it and did some more reboots and shutdowns. All was ok. Then out of the blue comes another "DISK BOOT FAILURE" and again, if the Win7 install DVD is in the drive it boots fine. So, is the SSD a bad'un? TIA UPDATE: It was a BIOS issue! I found a hidden away option for HDD boot order, which was separate from the usual HDD/CDRom/FDD boot order option. The WD was set to boot before the SSD... Swapped them round and all is well. Still don't understand how it worked at first though... Thanks Solaris

    Read the article

  • Subdocument in Word won't save

    - by ChrisW
    Because I know Word has a history of not liking very large documents (my supervisor specifically told me not to use LaTeX... grr), I decided to learn the Master document / subdocument feature of Word when writing my PhD thesis. I have the title page / table of contents etc in the master document, and each chapter as a separate document. However, when I save the master document, it appears to save all the chapter documents apart from one (Chapter 4), for which it brings up the Save Document dialog box, helpfully with "Chapter4.docx" in the "Save as" box (n.b. Chpater4.dox is not open). Clicking save does nothing, and doesn't make the dialog box go away. Saving as a different document means that my changes aren't reflected in the same document. There must be some reason Word doesn't like this particular document but I've got no idea why - there's nothing special in it that isn't in any of the other chapters. I have tried closing all documents, renaming Chapter4.docx, opening the master document, expanding all documents, OKing the warning that Chapter4.dox does not exist, and inserting the 'new' document, but even when I save the master document it still won't save the new Chapter4 document. If anyone knows any reason why Word is acting like this (or if I'm doing anything stupid), I'll be eternally grateful (p.s. sorry for the long rambling message. It's late; I've been working on my PhD 4.5 years, I really really want to throw this computer out the window, and I hope people are kind enough not to downvote this question because of it's rambling nature!) Update With Word closed, I've tried to delete Chapter4.docx (having made a backup!) - but I get a warning that it can't be deleted because it's open in Microsoft Word... these files are on a network drive and the same problems are happening on 2 different computers. I could login to the filestore through ssh and force the file to be deleted, but I'm curious to know why this is happening!

    Read the article

  • Why does Windows Firewall want to block Google Chrome today?

    - by hippietrail
    I've been using the same public Wi-Fi (staying in a guesthouse) for over a week now. But this morning for the first time I got this puzzling warning from Windows Firewall: Why does Windows Firewall want to block one of the world's most popular web browsers today after being fine with it for years, and being fine with it on this connection for a week? Could it hinge on the words, some features? If so could it be something like a rare or new feature of Chrome that uses a different HTTP port? And if so why doesn't the security alert tell me any more about it? Or could it be a known bug in Windows Firewall? Or perhaps a known virus etc attaching itself to Google Chrome? Or is there a chance it's related to "Other browser makers follow Google's lead, revoke rogue certificates"? I haven't restarted Chrome for days and have downloaded but not installed a Windows update from a few days ago. So I'm not sure what may have managed to change on my machine since yesterday.

    Read the article

  • Windows 7 hangs after going into sleep a second time

    - by Brian Stephenson
    I've searched everywhere around Google and can't figure out why this is happening so I decide to ask here to see if anyone has a problem like this. Like it says in the title, whenever I sleep ONCE I'm able to wake the system, but going back to sleep again AFTER waking up for the first time results in it hanging on no input and no output, with the fan spinning as fast as possible and alot of heat being spewed out by the fan as well. I've tried various things like setting all USB Hub Root's to not get switched off for power saving, disabling USB selective suspend, disabling PCI-e link state power management, and even unplugging ALL USB devices and it wont wake up after the second attempt. And I've even waited up to a full hour of the CPU fan spinning loudly and it's still stuck trying to wake up. The only USB devices I use are a Microsoft USB Comfort Curve Keyboard 2000 (IntelliType Pro) and a generic HID compliant mouse from Creative model number OMC90S "CREATIVE MOUSE OPTICAL LITE". My other devices like external drives and controllers are unplugged when I'm not using them as having too many USB devices plugged in at a time causes a deadlock on almost all of the ports I have. Here's my system specifications (Most of these are from CPU-Z): Brand: Gateway DX4300-19 Mainboard: Gateway RS780 Chipset: AMD 780G Rev 00 Southbridge: AMD SB700 Rev 00 LPCIO: ITE IT8718 BIOS: American Megatrends Inc. ver P01-A4 09/15/2009 CPU: AMD Phenom II X4 810 at 2.60 GHz RAM: 8.0 GB DDR2 Dual Channel Ganged Mode at 400 MHz GPU: ATI Radeon HD3200 Graphics Intergrated - RS780 OS: Windows 7 Home Premium x64 OEM (Acer Group) HDD: WDC WD10EADS-22M2B0 1.0 TB (Western Digital Green Caviar) My BIOS has absolutely no control over how I setup the sleep mode to be either S1 or S3. So I can't check these settings or even change them. Hybrid sleep is also disabled, I can successfully go into hibernation and wake from hibernation but this is painfully slow due to a harddrive problem I'm having with this "Green Drive". (Hibernation takes over ~3 minutes to complete) Any help would be appreciated, thanks.

    Read the article

  • Domain workstation acting up and I can't track it down.

    - by DevNULL
    I have a developer with a Windows XP (SP2) 64 bit machine. If the machine is left on overnight (or any period of time longer than 5-6 hours) it takes 2-3 minutes to open any local drive and his network drives are no longer accessible. Here's what the system logs report... Any Help BTW: The problem just started a week ago and nothing has changed on the domain controller / AD or his machine. --- ERROR 1 Event Type: Error Event Source: NETLOGON Event Category: None Event ID: 5719 Date: 6/8/2010 Time: 9:17:26 AM User: N/A Computer: BFC1 Description: This computer was not able to set up a secure session with a domain controller in domain UR due to the following: There are currently no logon servers available to service the logon request. This may lead to authentication problems. Make sure that this computer is connected to the network. If the problem persists, please contact your domain administrator. ADDITIONAL INFO If this computer is a domain controller for the specified domain, it sets up the secure session to the primary domain controller emulator in the specified domain. Otherwise, this computer sets up the secure session to any domain controller in the specified domain. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: 5e 00 00 c0 ^..A --- ERROR 2 The machine-default permission settings do not grant Local Activation permission for the COM Server application with CLSID {555F3418-D99E-4E51-800A-6E89CFD8B1D7} to the user NT AUTHORITY\LOCAL SERVICE SID (S-1-5-19). This security permission can be modified using the Component Services administrative tool. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. --- ERROR 3 Event Type: Error Event Source: RemoteAccess Event Category: None Event ID: 20106 Date: 6/8/2010 Time: 10:12:18 AM User: N/A Computer: BFC1 Description: Unable to add the interface {E76F0A78-7A0B-4EBB-A081-BA3BD452FC4C} with the Router Manager for the IP protocol. The following error occurred: Cannot complete this function. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: eb 03 00 00 e...

    Read the article

  • Preferred mail system/server for a company?

    - by Trevoke
    Say you are responsible for setting up an email solution at a company. Which would be your choice? I know of the following options, but many of them not well: Gordano Mail System Exchange Exim Postfix Qmail Zimbra For having used it a little over two years, I really, really like Gordano Mail System. They offer a whole bunch of things, like calendaring, anti-spam, anti-virus, extremely complete and filterable logging options, aliases, a customizable webmail interface... And their software can be installed on both a Windows or Linux OS. In addition, their support is top-notch, their knowledgebase comprehensive (and, I will admit with a touch of pride, I have contributed, with my questions, to the addition of a few articles in there). Of course, they're not free, which can be a problem, but they're not Exchange, and they do offer pretty much everything that Exchange offers -- which is great if you want to stay away from that, but need all the features. Although, if you need a Blackberry Exchange Server, or something similar, I'm not sure what you should go for. So.. What would your choice be? Why? I've never played with a more DIY email solution, but I'm sure many people here have and wouldn't trade their setup for the world :)

    Read the article

  • Distortion problem with Creative audio equalizer

    - by e-t172
    Hi, I have a problem with the Creative Console EQ, I don't know if it's fixable or not (is the EQ software or hardware on these cards?). Basically, I have enormous distortion with certain sounds in the 30 - 125 hz range. When this happens I get some sort of "frrzzzz" (sorry, I'm french and don't really know the correct english word for that) on top of the original sound. I have a Sound Blaster Audigy SE. I'm using the Daniel_K drivers, on Windows 7 Profesionnal x64. All the effects are disabled except EQ. Steps to reproduce Put the card in 24bit/96khz mode. The problem is also present with 16bit/48khz but seems to be less audible. In the Creative Console, use the following EQ: (full size) Play this sound at a reasonably high volume. You should hear distortion on the two "booms". Especially the second one. Disable Creative EQ. Play the sound in an application with an integrated EQ (e.g. foobar2000, ffdshow) using the same EQ parameters. There is no distortion. Conclusion: the Creative EQ is broken. Is anyone having the same problem? I'm also interested in the results with other Creative cards or even other brands soundcards with a similar EQ feature.

    Read the article

  • What are the requirements for Windows Remote Assistance over Teredo?

    - by Jens
    I try to get the Windows 7 (or Vista) remote assistance feature to work, without using UPnP on the novices computer. After enabling Teredo on the expert's computer (that is in a corporate network, and therefore has teredo disabled by default), I tried to connect to the novice both using Easy Connect and the invitation file with no success. My triubleshooting included the following (so far). A connection to the novice from my home pc was successful, hinting at a misconfiguration on the experts side. Both computers have a "qualified" connection to the Teredo Server. Both computers have a valid Teredo IP, access to the Global_ PNRP cloud and can resolve names registered with PNRP on the other computer. The expert can resolve the PNRP Id automatically generated with an Easy Connect help request Both computers can ping the other's PNRP name. Both computers can ping the other's Teredo IP Address using ping -6 Now, I am a little stumped. I expected Remote Assistance to work at this point, since my corporate firewall has no Teredo filtering. What could RA cause not to work in this setting? Thanks in advance!

    Read the article

  • Recommendation for robust, customizable, open source, Java servlet-based forum software?

    - by Erik Hermansen
    There is a lot of forum software out there, but it seems to me that a lot of the popular choices are PHP-based. And for my project, I'd like something based on Java servlets so my team can make customizations to it. Another important feature is that I can completely change the pages to hide unwanted elements without too much work. So I'm looking either for a template system or easily editable scripts (i.e. JSPs) that have a clean view separation. Just having skin changes or CSS customization is not enough. I understand that if I have open source, I can change anything I want, but my point is that it should be easy and not requiring mastery of a complex code base. Finally, I want something that has been around for at least a year and deployed on some high-traffic sites. Clustering support (one database, multiple web servers) is highly desirable. Up-time is crucial since I have an SLA to support. What do you think?

    Read the article

  • mshtml.dll latest version for Internet Explorer 8, Windows XP Service Pack 3

    - by AllSolutions
    Many applications in my system (Internet Explorer 8, Yahoo Messenger, Skype 10) are crashing and error details shows module name mshtml.dll. I checked the version of mshtml.dll in system32 folder. It is 8.0.6001.19170. My Internet Explorer version is 8.0.6001.18702. I am not concerned about crash of IE, because I generally use Firefox, but how do I solve the crashes in other applications, which are due to mshtml.dll? I have moved to Windows XP Service Pack 3 (32 bit). I have tried to update Internet Explorer 8 (from Tools-Windows Update), but again it crashes. I can not migrate to IE 9, as it requires Vista or Windows 7. I have applied Cumulative Security update for IE8, which has this file name: IE8-WindowsXP-KB2618444-x86-ENU.exe I could not get much info from Microsoft sites or Google. I do not want to use Automatic Updates feature of Windows. Can somebody give the download links for mshtml.dll and any associated files, which I can replace in system32 folder? Thanks.

    Read the article

  • Are there any disadvantages of having a "free fall sensor" on a hard disk drive?

    - by therobyouknow
    This is a general question that came out of a specific comparison between the Western Digital Scorpio WD3200BEKT and Western Digital Scorpio WD3200BJKT (which is the same as the former but with a free fall sensor.) Note: I'm not asking for a review or appraisal of these specific drives, as the general question does apply on other brands as well. Though your input would help my decision. To break down the general question in order to answer it, I would be looking for comments on things like: if it's necessary to have differing physical dimensions between free fall sensor drives and those without, e.g. does it make it any thicker, and therefore reduce the systems where it can be installed - particularly smaller laptops? does it actually make the system less reliable - because of false alarms whereby the drive thought the laptop was falling but it wasn't? I suppose that the fact that a manufacturer produces both drives with and without free fall sensors says something about possible disadvantages. Or it could be standard marketing techniques where by making drives with and without results in larger sales volume than just those with the feature alone.

    Read the article

  • Vim - Displaying Code Output in a New Window á la Textmate?

    - by Michael Density
    A few months back I switched from Textmate to Vim. Overall I really love Vim, but one of the things I miss from Textmate is using the ⌘R command to run Ruby code and having the results neatly pop up in a new, scrollable window. Obviously, Vim is capable of running Ruby code and displaying the output with :w !ruby. The only downside to this is that if the resulting output is too long I can't scroll through it. To combat this problem I tried modifying a :redir function from Vim Tips. It looks like this: function! TabNew(cmd) redir => message silent execute a:cmd redir END tabnew silent put=message set nomodified endfunction command! -nargs=+ -complete=command TabNew call TabNew(<q-args>) Now the output from Ruby is put into a new tab. However, I can't get it to pop up in a new, separate window. Changing tabnew to new just sends the output to a split in the same window. The other problem is that a visible ^M gets appended to the end of each line, so the output ends up looking like this, which is kind of bothersome: Hello World!^M So, is there any way to get the output into a separate window without the ^M appended to the end? Are there any plugins I should be trying to achieve this Textmate-like effect for code output?

    Read the article

  • Restoring Windows 2008 Server X86 and X64

    - by rihatum
    Restoring Windows 2008 Server (Domain Controller) We are using Backup Exec System Recovery 2010 to Image our DC. Now this software has a feature to convert the backup into a vmware or hyper-v VM I have also used disk2vhd to convert one of our dc's to a vhd and when I connected it into Hyper-V, it booted fine, I can login - BUT :-) As soon as I login, I get the activation error, that change product key, this product key isn't good for this machine etc. Question is : When in a real recovery situation, what would be the procedure to restore it either virtual or onto a physical box but be able to login and change product key etc ? In this scenario its just locked down and I cant' do anything, if this is the case, how would I replicate my production environment via these tools ? Any Ideas ? Will be grateful for some real world examples here. Same thing happens with our exchange backup / test restore either physical or virtual, can login but nothing else. Now we don't have the keys as they are OEM keys and just wondering what will happen in a real scenario, would we be purchasing another KEY or using the OEM key on our new server ? This is a test environment I am trying to create by restoring our backups either into hyper-v or physical test machines. Also, If I build up a machine (Server 2008) in a VM (Hyper-V), How can I restore just the system state backup of my DC into it ? will that give me the activation error too ? even though I would use the TRIAL ISOs provided by Microsoft ? Kind regards

    Read the article

< Previous Page | 540 541 542 543 544 545 546 547 548 549 550 551  | Next Page >