Search Results

Search found 14738 results on 590 pages for 'outlook settings'.

Page 546/590 | < Previous Page | 542 543 544 545 546 547 548 549 550 551 552 553  | Next Page >

• Hard freeze on new computer

  - by mphair

  OCZ Gold 3x2GB 240-Pin DDR3 SDRAM PC312800 Palit NE5T240SFHD01 GeForce GT240 1GB 128-bit GDDR5 ASUS P7P55D-E LGA 1156 P55 SATA 6Gb/s USB 3.0 ATX Intel Motherboard Intel Core i7-860 Lynnfield 2.8GHz 8MB L3 Cache LGA 1156 95W Quad-Core Processor SAMSUNG 22X Optical drive (DVD+-R/RW) CORSAIR CMPSU-620HX 620W ATX12V V2.2 Windows 7 Ultimate x64 Brand new system (got it from newegg two days ago) and it booted up and installed windows and ran for a day just fine. Yesterday, I boot it up in the afternoon and run various games at full graphics for most of the day. I turn on WoW and play for a few hours and it hard stalls. No numlock switching, no mouse feedback but nothing going wrong on the screen. No BSOD. I wait a bit to see if the stall is just a temporary one, but then force shutdown the computer. Upon reboot, everything seems fine, windows sees that it didn't shut down properly but I go into normal boot and restart WoW. I'm able to load it up and start running around when it freezes again. This time when I restart, it doesn't even get to BIOS. It starts (power goes on) and it just hangs with no output to the monitors. I shut it off and went to bed. This morning, I turned it on and went into BIOS setup. I'm not terribly experienced with messing with BIOS settings but I checked over them the best I could. Everything seems fine so I boot into windows and browse the internet for a bit looking for a solution, hard freeze within 10 minutes. I restart and go into BIOS and check the CPU temperature, 40c. I'm kinda stumped here. Some people say it might be a memory issue, but why would it take so long for it to come up? Could it have been slowly accessing one memory stick at a time and then it just got to a bad one and that's what is causing it to fail? It seems odd that I don't get a BSOD from a hardware failure. Having the screen just halt with no input or output change seems like a software thing to me. Any thoughts?

  Read the article

• Windows doesn't get access to internet though linux easily does

  - by flashnik

  We have a very interesting problem. The network is configured in this way: internet is connected to Trendnet switch TS DHCP server at 192.168.0.1 running on Ubuntu (S) is connected to internet switch DNS is also configured on 192.168.0.1 on S D-Link Wi-Fi boosters are connected to switch TS PCs use D-Link PCI-E Wi-Fi cards to get access to network PCs have both Ubuntu and Windows 7 There are about 40 PCs. When PC is booted to Ubuntu it easily gets access to internet. But when it's booted to Windows 7, it gets a valid IP-address, but doesn't get access to internet. The address, mask, DNS, GW-address are totally the same as when it's booted under Ubuntu. The S is reacheble and pingable. Sometimes when we are lucky the PC gets access to Internet, but after rebooting it can lose it. When PC under Windows has access, it has totally the same settings as when it doesn't. What can be done? UPDATE I shared a dropbox with 2 captures of traffic. Ping.pcap is a capture of pinging 8.8.8.8. And google-browser.pcap is a capture of opening a google.com in a browser, both of them are in tcpdump formats and made by Wireshark on Win PC. The MAC of Win PC ends on b7:63 and IP is 192.168.0.130. UPDATE2 This is ifconfig output from Ubuntu Server eth0 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8d inet addr:193.200.211.74 Bcast:193.200.211.78 Mask:255.255.255.0 inet6 addr: fe80::21e:67ff:fe13:d58d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:196284 errors:0 dropped:44 overruns:0 frame:0 TX packets:190682 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:158032255 (158.0 MB) TX bytes:156441225 (156.4 MB) Interrupt:19 Memory:c1400000-c1420000 eth0:2 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8d inet addr:192.168.0.1 Bcast:192.168.0.254 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 Interrupt:19 Memory:c1400000-c1420000 eth1 Link encap:Ethernet HWaddr 00:1e:67:13:d5:8c UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:16 Memory:c1300000-c1320000 nslookup from Win results in DNS request timeout, nbtstat in 'not found'.

  Read the article

• Bypassing "Found New Hardware Wizard" / Setting Windows to Install Drivers Automatically

  - by Synetech inc.

  Hi, My motherboard finally died after the better part of a decade, so I bought a used system. I put my old hard-drive and sound-card in the new system, and connected my old keyboard and mouse (the rest of the components—CPU, RAM, mobo, video card—are from the new system). I knew beforehand that it would be a challenge to get Windows to boot and install drivers for the new hardware (particularly since the foundational components are new), but I am completely unable to even attempt to get through the work of installing drivers for things like the video card because the keyboard and mouse won't work (they do work, in the BIOS screen, in DOS mode, in Windows 7, in XP's boot menu, etc., just not in Windows XP itself). Whenever I try to boot XP (in normal or safe mode), I get a bunch of balloons popping up for all the new hardware detected, and a New Hardware Found Wizard for Processor (obviously it has to install drivers for the lowest-level components on up). Unfortunately I cannot click Next since the keyboard and mouse won't work yet because the motherboard drivers (for the PS/2 or USB ports) are not yet installed. I even tried a serial mouse, but to no avail—again, it does work in DOS, 7, etc., but not XP because it doesn't have the serial port driver installed. I tried mounting the SOFTWARE and SYSTEM hives under Windows 7 in order to manually set the "unsigned drivers warning" to ignore (using both of the driver-signing policy settings that I found references to). That didn't work; I still get the wizard. They are not even fancy, proprietary, third-party, or unsigned drivers. They are drivers that come with Windows—as the drivers for CPU, RAM, IDE controller, etc. tend to be. And the keyboard and mouse drivers are the generic ones at that (but like I said, those are irrelevant since the drivers for the ports that they are connected to are not yet installed). Obviously at some point in time over the past several years, a setting got changed to make Windows always prompt me when it detects new hardware. (It was also configured to show the Shutdown Event Tracker on abnormal shutdowns, so I had to turn that off so that I could even see the desktop.) Oh, and I tried deleting all of the PNF files so that they get regenerated, but that too did not help. Does anyone know how I can reset Windows to at least try to automatically install drivers for new hardware before prompting me if it fails? Conversely, does anyone know how exactly one turns off automatic driver installation (and prompt with the wizard)? Thanks a lot.

  Read the article

• Ubuntu Lucid: Erratic screen behaviour after boot

  - by fgysin

  In short: about 50% of the time I have a screwed up monitor setup after reboot. About 50% it is totally correct. Now the longer version: I updated my machine from 9.04 to 10.04 (via 9.10). At first I run into some monitor problems (I have a 3-monitor setup) because of the known bug in the new xserver driver for xinerama. This messes up behaviour if the mouse goes either left or above the screen number 0, i.e. I had to make my left-most monitor screen 0. Everything worked out fine finally, I got my 3-monitor setup back with xinerama enabled to get one big desktop streched over 3 screens. Now the fun part: Every time I start up my machine only one of the 3 monitors gets a signal and is woken up: it only recognizes the left-most monitor (screen 0) and crams all the desktop stuff into this one screen. If I go into nvidia settings I only see one physical device although all 3 are connected and have power. When I look into the xorg.conf I can still see my old setup with 3 devices, 3 screens, xinerama active etc... But I was totally unable to get 3 montitors to work. (I tried unplugging monitors, reconfiguring whole nvidia setup, ...) But it gets even better: When I restart my machine (i.e. choose the restart option from the Ubuntu menu) it shuts down and tries to restart. The restart then gets stuck after showing the Ubuntu splash screen with the 'loading bar' (the moving dots thingy) and I am forced to kill the machine by cutting power. But after the power cut the machine boots up normally and suddenly I get my 3 monitor setup back up working. That is until the next time I shut down and start up, where it all starts over again and I only have one monitor... (see above) I really have a hard time seeing where the error is. It must be that the restart boot somehow differs from the 'normal' boot. But the fact that it gets stuck and I need to cut power which then basically triggers a 'normal' boot does not really support this theory... My setup (please tell me if you need further info): 3 monitors as 3 screens as one desktop (with xinerama) 2 nvidia cards where screen 0 and 1 are on card 0 and screen 2 is on card 1 Ubuntu 10.04 Lucid Lynx (updated from 9.10, 9.04, ....) I would appreciate every idea on the subject, at the moment I really don't have any clue what to do...

  Read the article

• Apache server completely freezes until it gets restarted

  - by nbv4

  My server does this every few days. What sucks is that it always seems to do this right after I go to bed, so when I wake up, I'm greeted with the fact that my server has been down for the past 6 or 7 hours. When I first noticed this, I added a cronjob that tries to restart the server every 15 minutes, but I guess that didn't fix it. Once I noticed the server was down, I can this command: /etc/init.d/apache2 restart * Restarting web server apache2 apache2: Could not reliably determine the server's fully qualified domain name, using 127.0.0.1 for ServerName ... waiting ...........................................................apache2: Could not reliably determine the server's fully qualified domain name, using 127.0.0.1 for ServerName httpd (pid 17597) already running ...which is odd, because a restart should restart the server, even if it's already running, correct? I eventually had to "stop" then "start" to get it working again. I then looked through the logs, and found something very weird. It seems that around the time the server crashed, the logs have entries that are wildly out of order. It looks a little like this: xx.xxx.xxx.x - - [21/Apr/2010:06:32:05 -0400] "GET / blah" xx.xxx.xxx.x - - [21/Apr/2010:06:51:25 -0400] "GET / blah" x.xx.xxx.xxx - - [21/Apr/2010:06:38:23 -0400] "GET / blah" xxx.xx.xx.xx - - [21/Apr/2010:06:31:56 -0400] "GET / blah" xxx.xx.xx.xx - - [21/Apr/2010:06:51:49 -0400] "GET / blah" xx.xx.xxx.xx - - [21/Apr/2010:06:33:20 -0400] "GET / blah" I don't think the problem is memory, because this: tells me that right before the crash, memory usage is fine. I'm running apache with the worker mpm, here are the settings for that: <IfModule mpm_worker_module> StartServers 1 MaxClients 100 MinSpareThreads 5 MaxSpareThreads 10 ThreadsPerChild 10 MaxRequestsPerChild 3000 </IfModule> This apache server is running a bunch of stuff, but most of the traffic comes from a django project I'm hosting, that uses mod_wsgi. There also is a simple machines forum that is running off of mod_fcgid. Those setting are below: <IfModule mod_fcgid.c> MaxRequestsPerProcess 500 MaxProcessCount 3 AddHandler fcgid-script .php .fcgi AddHandler cgi-script .cgi .pl FCGIWrapper "/usr/bin/php-cgi" .php </IfModule> Anyone know of anything else I can check? I've just about tweaked every single setting I can think of, yet these freezes still happen.

  Read the article

• Is it possible to "stealth" dual boot a machine?

  - by BrianH

  I have a loaner laptop that has MS Windows with locked down permissions. It works okay for what I need to do, but I started wondering if there was a way to install a separate Windows OS on a separate hard drive to do what I want to do on it. Virtual I wish I could use VirtualBox or VMWare, but that is not an option (I even tried VBox portable). External Drive My next trial was see if it was possible to install Windows on an external drive, and then plug that drive in and boot from it whenever I wanted my own OS. After a few Google searches, I see that is not really a possibility. Swap Primary Drive Another option, would be to get a second internal hard drive, take the existing HD out, and install a new Windows OS on the secondary HD. This would mean swapping the internal hard drive each time I want to switch OSs - doable, but not very convenient. Dual Boot The laptop has an expansion slot where a second hard drive can be plugged in quickly. I thought about Dual booting, but I don't want to mess with the MBR on the primary hard drive. When I have to give the laptop back, I don't want a dual-boot screen to popup. Summary Is there a way to have 2 hard-drives on a machine, each with it's own OS, and maybe use BIOS settings to have only 1 hard drive active at a time? That way both hard drives could be physically connected, but only one would actually be active at a time. I basically want a second OS that does not (can not) affect the existing OS in any way, and can be removed at any time without affecting the existing OS. The secondary OS does not need any of the files on the main hard drive - it's basically like having 2 separate computers using the same hard ware... Is this possible, or would it be easier just to go out and buy a different laptop? Thanks in advance! EDIT I just discovered that my BIOS allows me to pick (at startup) which hard drive I want to boot from. I poked around in the BIOS and there is not a place to disable certain devices, like the primary hard drive. My only concern about plugging in a second hard drive and installing Windows to the second hard drive is that it will mess with the primary hard drive, or add a bootloader screen to pick which windows install to use. My thought would be to physically unplug the primary, plug in the secondary and install windows to the secondary. After the install is working properly, I can plug the primary back in and use the BIOS feature to determine which drive to boot to. Is there any way after I have 2 separate installs on 2 separate hard drives that one of the installs could mess with the MBR on the other drive?

  Read the article

• Unable to telnet out on port 25 on windows server 2008

  - by NickGPS

  Hi All, I just setup a Windows 2008 R2 server and am trying to get a basic mail server up and running so that I can send emails from my applications. I setup a virtual SMTP server in IIS6 and tried doing a local telnet to port 25, which seemed to work fine. There were no errors during this stage and I can see the mail message appear in the Queue folder. The problem is that mail never leaves the Queue folder. I then tried to telnet to a remote mail server on port 25 but couldn't connect:- telnet 209.85.227.27 25 Could not open connection to the host, on port 25: Connection failed) I checked my firewall and there is a default setting to allow all outgoing TCP traffic with no restriction. I even setup a specific rule for outgoing port 25 traffic but to no avail. I then ran a SmtpDiag.exe command .\SmtpDiag.exe [email protected] [email protected] and received the following output Searching for Exchange external DNS settings. Computer name is WIN-SERVERNAME. Failed to connect to the domain controller. Error: 8007054b Checking SOA for gmail.com. Checking external DNS servers. Checking internal DNS servers. SOA serial number match: Passed. Checking local domain records. Checking MX records using TCP: gmail.com. Checking MX records using UDP: gmail.com. Both TCP and UDP queries succeeded. Local DNS test passed. Checking remote domain records. Checking MX records using TCP: gmail.com. Checking MX records using UDP: gmail.com. Both TCP and UDP queries succeeded. Remote DNS test passed. Checking MX servers listed for [email protected]. Connecting to gmail-smtp-in.l.google.com [209.85.227.27] on port 25. Connecting to the server failed. Error: 10060 Failed to submit mail to gmail-smtp-in.l.google.com. Is there any other diagnostics I can do to figure out if it's my firewall or something else? I have removed antivirus to make sure that it wasn't causing the problem. Any ideas would be much appreciated.

  Read the article

• Suspected network performance issue on VirtualBox Ubuntu guest on Win7 host

  - by Adam

  I set up Ubuntu 12.04 in VirtualBox on the Win7 machine I was allocated on my new project. I am running Java, Eclipse, Tomcat to develop a large data-intensive application and I noticed that this application runs at half the speed of my colleague's identical machine, where he runs it all under Windows. I think I have narrowed down the performance issue to the network, after comparing and equalising all the Java VM settings with my colleague. Is there a ping test I can do or some other network diagnostic test to flag up any problems? To give some background, the network performance is confusing. Running a network speed test to my colleague's machine with iperf shows speeds of 6 Mb/s from my Ubuntu guest, and 90 Mb/s from the win7 host. Large downloads, e.g. the Java SDK, come down at about 1.2 MB/s on both the guest and the host. Pings are sub-1ms on the host, but 1.5ms on the guest. I also did a broadband speed test, and got 10Mb/s download speed on both, but the host has an upload speed of 10Mb/s but the guest only uploads at 3Mb/s. I've been trying to diagnose any MTU problems with ping -M do to identify any kind of packet fragmentation problem but it's progressing very slow because I don't have much experience in this area. From what I read on other people's networking issues with VB and Linux guests on Win7 hosts, I should be able to get the speed on the guest up to the same level as the host. I installed a fresh VM with Ubuntu again to see if I'd foobar'd it somehow, but I'm getting the same readings with iperf on the virgin installation. My setup is: Adapter 1: Intel PRO/1000 MT Desktop (NAT) Adapter 2: ditto (host-only adapter) eth0 Link encap:Ethernet HWaddr 08:00:27:0b:76:bf inet addr:10.0.2.15 Bcast:10.0.2.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fe0b:76bf/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:86236 errors:0 dropped:0 overruns:0 frame:0 TX packets:49369 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:69163946 (69.1 MB) TX bytes:3530535 (3.5 MB) eth2 Link encap:Ethernet HWaddr 08:00:27:a3:26:b8 inet addr:192.168.56.101 Bcast:192.168.56.255 Mask:255.255.255.0 inet6 addr: fe80::a00:27ff:fea3:26b8/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:59 errors:0 dropped:0 overruns:0 frame:0 TX packets:57 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:9148 (9.1 KB) TX bytes:7648 (7.6 KB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:701 errors:0 dropped:0 overruns:0 frame:0 TX packets:701 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:66321 (66.3 KB) TX bytes:66321 (66.3 KB)

  Read the article

• Is it possible to change an "Unidentified Network" into a "Home" or "Work" network on Windows 7

  - by Rhys

  I have a problem with Windows 7 RC (7100). I frequently use a crossover network cable on WinXP with static IP addresses to connect to various industrial devices (e.g. robots, pumps, valves or even other Windows PCs) that have Ethernet network ports. When I do this on Windows 7, the network connection is classed as an "Unidentified Network" in Networks and Sharing Center and the public firewall profile is enforced by Windows. I do not want to change the public profile and would prefer to use the Home or Work profile instead. For other networks like Home and Work I'm able to click on them and change the classification. This is not available for unidentified networks. My questions are these:- Is there a way to manual override the "Unidentified Network" classification? What tests are performed on the network that fail, therefore classifying it as an "Unidentified Network" By googling (hitting mainly vista issues) it seems that you need to ensure that the default gateway is not 0.0.0.0. I've done this. I've also tried to remove IPv6 but this does not seem possible on Windows 7. UPDATE For those still having problems here is the answer to my issue and the possible reasons why:- Win7 keeps a list of the networks you visit by (I am assuming, but don’t know for sure) the MACID of the device pointed to by the Default Gateway. The default gateway is usually the constant device in a network (i.e. the NAT or router) so can be used to uniquely identify one network from another. The default gateway in the IPv4 properties panel must therefore point to an actual endpoint so windows can then keep track of it. If there is a device at the end of the Default Gateway windows will identify it and track it remembering its settings. The ways you can therefore fool Win7 is to either point the default gateway to your own IP address, or the IP address of the target device you’re communicating with. This will have the side effect of expecting that target device to start routing packets for IP destinations that are outside your subnet. So some applications on Win7 will try to communicate with the internet, these will be passed on to the default gateway (either back you the same IP address or a target device that is not a router) and thus will eventually timeout because neither can route packets. Which you can usually live with. This gets slightly complicated when you mix a this type of connection with a real connection to the internet via WIFI. The wired network card usually has priority when routing because of the “interface metric” so some applications might not connect correctly.

  Read the article

• Can't validate mine, sudo nor root in Debian "Jessie" Gnome anymore?

  - by Janar

  I'm Debian beginner & GUI guy in a bit of trouble? Can't login as sudo/gksu/root/su nor as (main/super)user after removed user password via Gnome-user-settings. History of actions (Probably irrelevant though) Installed Debian "Jessie" GNU/Linux with xFce GUI (en-US) as only OS. HardWare is ThinkPad w510. Skipped root user password in setup, to get sudo for superuser easily. Logged in (as always had) with Gnome (3.4.x), not once with xFCE. (installed Xfce. Installed xFce only to achieve more control (easier management) over packages this way, to set-up gnome much more by mine likes. Added more jessie repros (same ones as in Wheesy stable by default but for Jessie as, Jessie only had repros for security updates by default). Installed lots of gtk(3) & gnome(3) based soft; (- restarted again after this) Installed propietary graphics card driver for mine nvidia quadro. (- restarted once again after that one) Installed more stuff related to mine work/school/devel. The actual problem Had a plan to restart again, but wanted to set up auto-login first, instead set user password to none (don't ask why / perhaps caused by being awake for a looooong time), noticed it, and set also to auto-login, but couldn't undo mine previous mistake to create new password for me. As mine password is set to none I would have expected that simply return in pass prompt for emty password field would do, but it won't authenticate. I tried Alt+F2 "gksu gedit" as well as: sudo wget "https://www.some-page.eu/file.ext" and "su" in terminals, none has applied (quite logical actually - as I'm sudoer and highest ranked super user, besides only user in computer). Current stand Everything worked & still works nice after this accident, besides this password prompts part. To spoked to log-out nor restart. Synaptic package-manager is still open with root rights (only one, that has left open prior to the issue and not closed since, just in case). Goggled for help and read some manuals/faqs/how-tos - mostly lead to sudoers file management, but not found one specifically for mine issue - so still not any smarter. Really hope, that I don't have to redo OS inst all over again, by just one stupid mistake. Thanks for your reply :-)

  Read the article

• A proper way to create non-interactive accounts?

  - by AndreyT

  In order to use password-protected file sharing in a basic home network I want to create a number of non-interactive user accounts on a Windows 8 Pro machine in addition to the existing set of interactive accounts. The users that corresponds to those extra accounts will not use this machine interactively, so I don't want their accounts to be available for logon and I don't want their names to appear on welcome screen. In older versions of Windows Pro (up to Windows 7) I did this by first creating the accounts as members of "Users" group, and then including them into "Deny logon locally" list in Local Security Policy settings. This always had the desired effect. However, my question is whether this is the right/best way to do it. The reason I'm asking is that even though this method works in Windows 8 Pro as well, it has one little quirk: interactive users from "User" group are still able to see these extra user names when they go to the Metro screen and hit their own user name in the top-right corner (i.e. open "Sign out/Lock" menu). The command list that drops out contains "Sign out" and "Lock" commands as well as the names of other users (for "switch user" functionality). For some reason that list includes the extra users from "Deny logon locally" list. It is interesting to note that this happens when the current user belongs to "Users" group, but it does not happen when the current user is from "Administrators". For example, let's say I have three accounts on the machine: "Administrator" (from "Administrators", can logon locally), "A" (from "Users", can logon locally), "B" (from "Users", denied logon locally). When "Administrator" is logged in, he can only see user "A" listed in his Metro "Sign out/Lock" menu, i.e. all works as it should. But when user "A" is logged in, he can see both "Administrator" and user "B" in his "Sign out/Lock" menu. Expectedly, in the above example trying to switch from user "A" to user "B" by hitting "B" in the menu does not work: Windows jumps to welcome screen that lists only "Administrator" and "A". Anyway, on the surface this appears to be an interface-level bug in Windows 8. However, I'm wondering if going through "Deny logon locally" setting is the right way to do it in Windows 8. Is there any other way to create a hidden non-interactive user account?

  Read the article

• Proxy Error 502 "Reason: Error reading from remote server" with Apache 2.2.3 (Debian) mod_proxy and Jetty 6.1.18

  - by Martin

  Apache is receiving requests at port :80 and proxying them to Jetty at port :8080 The proxy server received an invalid response from an upstream server The proxy server could not handle the request GET /. My dilemma: Everything works fine normally (fast requests, few seconds or few tens of seconds long requests are processed ok). Problems occur when request processing takes long (few minutes?). If I issue request instead directly to Jetty at port :8080 the request is processed OK. So problem is likely to sit somewhere between Apache and Jetty where I am using mod_proxy. How to solve this? I have already tried some "tricks" related to KeepAlive settings, without luck. Here is my current configuration, any suggestions? #keepalive Off ## I have tried this, does not help #SetEnv force-proxy-request-1.0 1 ## I have tried this, does not help #SetEnv proxy-nokeepalive 1 ## I have tried this, does not help #SetEnv proxy-initial-not-pooled 1 ## I have tried this, does not help KeepAlive 20 ## I have tried this, does not help KeepAliveTimeout 600 ## I have tried this, does not help ProxyTimeout 600 ## I have tried this, does not help NameVirtualHost *:80 <VirtualHost _default_:80> ServerAdmin [email protected] ServerName www.mydomain.fi ServerAlias mydomain.fi mydomain.com mydomain www.mydomain.com ProxyRequests On ProxyVia On <Proxy *> Order deny,allow Allow from all </Proxy> ProxyRequests Off ProxyPass / http://www.mydomain.fi:8080/ retry=1 acquire=3000 timeout=600 ProxyPassReverse / http://www.mydomain.fi:8080/ RewriteEngine On RewriteCond %{SERVER_NAME} !^www\.mydomain\.fi RewriteRule /(.*) http://www.mydomain.fi/$1 [redirect=301L] ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined ServerSignature On </VirtualHost> Here is also the debug log from a failing request: 74.125.43.99 - - [29/Sep/2010:20:15:40 +0300] "GET /?wicket:bookmarkablePage=newWindow:com.mydomain.view.application.reports.SaveReportPage HTTP/1.1" 502 355 "https://www.mydomain.fi/?wicket:interface=:0:2:::" "Mozilla/5.0 (Windows; U; Windows NT 6.1; fi; rv:1.9.2.10) Gecko/20100914 Firefox/3.6.10" [Wed Sep 29 20:20:40 2010] [error] [client 74.125.43.99] proxy: error reading status line from remote server www.mydomain.fi, referer: https://www.mydomain.fi/?wicket:interface=:0:2::: [Wed Sep 29 20:20:40 2010] [error] [client 74.125.43.99] proxy: Error reading from remote server returned by /, referer: https://www.mydomain.fi/?wicket:interface=:0:2:::

  Read the article

• My network drive disappears from Mac OS Finder

  - by Mariusz

  I have recently bought a Netgear WNDR3800 router to use it in my home network. But just the same day I installed it, I noticed a strange behaviour of Finder and iTunes. Let me explain it further. There is a Synology DS111 NAS attached to that router and two Macs with Mac OS X Lion. One of them is connected by a cable and the second one wirelessly. Before I changed my router to the new one I mentioned above, Finder always used to display my NAS on its sidebar. So I could just click its network name to access shared folders existing on it. But after I installed WNDR3800, I can no longer access the NAS that way. It is no longer displayed. I always have to mount it manually by typing its IP address using the Finder's 'connect to server' option. The same NAS supports TimeMachine backups and has an inbuilt DLNA server. And the same situation here. I can't perform a backup because my NAS is no longer accessible in TimeMachine preferences. iTunes does not display it as well (as a multimedia server) even though it used to before I installed that router. What's important, everything works fine for a couple of minutes after I restart the router or the NAS. Or even when I change the NAS's IP address it becomes accessible again in Finder, TimeMachine and iTunes, but only for some time. Both the Mac computers I mentioned behave the same way. And all those issues have been taking place sice I installed that new router. Before I did that, everything had worked fine. My old router was Netgear WGR614v10. Would you be so kind to tell me what you think could possibly be the reason of that behaviour? What settings of the router should I look closer at? I'm not a network specialist, but is it possible that some network packets are blocked for some reason? I will be grateful for any clues you give me. Thank you.

  Read the article

• What's the best scenario for using a wireless router with Comcast Business Class

  - by Buck

  Just had Comcast Business Class internet installed (usage details at bottom of post). During the call to order I asked about the hardware they'd be providing and was told it was a docsis 3 modem that I'd have to pay $7.00/month for. Figuring I'd have to buy a router anyway, I decided to get my own modem - a Surfboard SB6121 Docsis 3. I called in to tech support to ask some questions and learned that the modem they would have provided DID have a router built in. It's an SMCD3G-CCR. It's not wireless (we need wireless). The guy explained that it was better to have their hardware here because if there's a problem with our service and we're using our own hardware, chances are they'll blame it on our hardware and do nothing since they don't support it. He explained that I could still hang my own wireless router off their modem/router and if we ever had any service problems, we'd be able to plug directly into their hardware and they'd be able to tell where the problem is and they wouldn't be able to pawn it off onto "customer provided equipment". That all said, a few questions: 1. Am I better off returning my Surfboard modem and getting the Comcast one? If I get a wireless router and plug into one of the ethernet ports of the Comcast device, should I NOT plug anything else into the Comcast device since it would be a different network from anything connecting via the wireless router? Is that correct? Given that I know VERY LITTLE about networking and setting up hardware like this... since I need wireless and will HAVE to get a wireless router to work with this Comcast device, do I need to do anything with the settings of the Comcast device? Do I use security on the Comcast device or the wireless router or both? Any suggestions or anything I need to think about, given this scenario, in order to use a business-type voip service like RingCentral or Jive or Nextiva? Any recommendations on a wireless router for this scenario? We are running 2 PCs (possibly 3-4 in the future) - could be wired for the time being if needed but would prefer wireless; would like to have a networked hard drive and a networked printer; NEED business-type VOIP service asap for 2 phone lines. Would like to hook up some IP cameras at some point (but not the kind that require static IPs since I don't have one nor do I plan to pay Comcast another $15/month for one). I don't have or plan to have any type of web servers or anything like that. Want to use WPA or WPA2 security and take advantage of the NAT feature of the router for additional protection (that's the extent of my networking knowledge).

  Read the article

• Computer suddenly dies; screen displays weird flickering lines, then restarts

  - by Imray

  I've been having this terrible problem for a little while and just managed to get a picture of 'dead screen' for the first time and I am posting it to seek help. Randomly, at irregular intervals (typically once a week), while working on something (it's been different things every time) my computer will just suddenly go dead - the screen turns to exactly the picture below (the lines flicker a little bit), it hangs there for a few seconds and then restarts. Obviously this is extremely frustrating and I want to try to stop it. I've searched numerous postings with similar keywords but nothing exactly the same as mine. Does anyone have any idea what might be the cause of this? I would post all my system settings and installed programs but the list is long and I don't know how much relevance each item would be. If you'd like to know something specific, please comment and I'll let you know whatever you need. SPECS C:\Users\Imray>systeminfo Host Name: Imray OS Name: Microsoft Windows 7 Professional OS Version: 6.1.7600 N/A Build 7600 OS Manufacturer: Microsoft Corporation OS Configuration: Standalone Workstation OS Build Type: Multiprocessor Free Registered Owner: Imray - Owner Registered Organization: Product ID: 00371-152-9333854-85895 Original Install Date: 06/09/1999, 5:45:21 PM System Boot Time: 22/03/2013, 8:58:18 AM System Manufacturer: Gateway System Model: DX4840 System Type: x64-based PC Processor(s): 1 Processor(s) Installed. [01]: Intel64 Family 6 Model 37 Stepping 2 GenuineIntel ~3201 Mhz BIOS Version: American Megatrends Inc. P01-A3 , 17/05/2010 Windows Directory: C:\Windows System Directory: C:\Windows\system32 Boot Device: \Device\HarddiskVolume2 System Locale: en-us;English (United States) Input Locale: en-us;English (United States) Time Zone: (UTC-05:00) Eastern Time (US & Canada) Total Physical Memory: 6,135 MB Available Physical Memory: 3,632 MB Virtual Memory: Max Size: 12,268 MB Virtual Memory: Available: 8,114 MB Virtual Memory: In Use: 4,154 MB Page File Location(s): C:\pagefile.sys Domain: WORKGROUP Logon Server: \\Imray-OWNER Hotfix(s): 4 Hotfix(s) Installed. [01]: KB971033 [02]: KB958559 [03]: KB977206 [04]: KB981889 Network Card(s): 2 NIC(s) Installed. [01]: 802.11n Wireless PCI Express Card LAN Adapter Connection Name: Wireless Network Connection DHCP Enabled: Yes DHCP Server: 192.168.2.1 IP address(es) [01]: 192.168.2.13 [02]: fe80::1df1:5399:6890:91f6 [02]: Microsoft Virtual WiFi Miniport Adapter Connection Name: Wireless Network Connection 2 DHCP Enabled: Yes DHCP Server: N/A IP address(es) Graphics Card Specs Name ATI Radeon HD 5570 PNP Device ID PCI\VEN_1002&DEV_68D9&SUBSYS_E142174B&REV_00\4&18A4B35E&0&0008 Adapter Type ATI display adapter (0x68D9), ATI Technologies Inc. compatible Adapter Description ATI Radeon HD 5570 Adapter RAM 1.00 GB (1,073,741,824 bytes) Installed Drivers atiu9p64 aticfx64 aticfx64 atiu9pag aticfx32 aticfx32 atiumd64 atidxx64 atidxx64 atiumdag atidxx32 atidxx32 atiumdva atiumd6a atitmm64 Driver Version 8.700.0.0 INF File oem1.inf (ati2mtag_Evergreen section) Color Planes Not Available Color Table Entries 4294967296 Resolution 1920 x 1080 x 59 hertz Bits/Pixel 32 Memory Address 0xD0000000-0xDFFFFFFF Memory Address 0xFBDE0000-0xFBDFFFFF I/O Port 0x0000D000-0x0000DFFF IRQ Channel IRQ 4294967293 I/O Port 0x000003B0-0x000003BB I/O Port 0x000003C0-0x000003DF Memory Address 0xA0000-0xBFFFF Driver c:\windows\system32\drivers\atikmpag.sys (8.14.1.6095, 181.00 KB (185,344 bytes), 06/09/1999 5:59 PM)

  Read the article

• HOW TO Convert DVD to iPad(Also converts to iPods)?

  - by goodm

  DVD to iPad Converter (Also converts to iPods) DVD to iPad Converter is the easiest-to-use and fastest DVD to iPad converter for Apple iPad movie and iPad video. It can convert almost any kind of DVD to iPad movie or iPad video format. It is also a powerful DVD to iPad converter with a conversion speed that is much faster than real-time. With this converter, you can use your iPad as a portable DVD player and enjoy your favorite DVDs on your iPad. http://www.softseeking.com/prodail.aspx?proid=83" Features of this DVD to iPad Converter Three Running Modes --In Direct Mode, you can directly click the DVD menu to select the movie you want to rip. This mode is very easy for ripping DVD movies. --In Batch Mode, you can select the DVD titles or chapters you want to rip via a checkbox list. This mode is very easy for batch ripping music DVDs, MTV DVDs and episodic DVDs. --In 1-Click Mode, you just need one click to open a DVD, after which the rest of the task will be done automatically. This is a “designed-for-dummies” mode. Input Types You can convert almost any kind of DVD format to iPad. Output Splitting You can split your output video by DVD chapters and titles. Fully supports MTV DVDs and episodic DVDs. File Size and Quality Adjustment You can customize the output file size and corresponding video quality. Flexible Output Profiles You can easily customize the various video settings such as brightness, bit rate, etc. Language Selection for Subtitles and Audio Track In Direct mode and in Batch mode, you can select the subtitle and audio track language. (In 1-Click mode, the default language is chosen automatically). Video Crop You can crop your video to 16:9, 4:3, full screen, etc. Video Resize You can resize your video. For example, you can set it to "Keep aspect ratio" or "Stretch to fit screen." Other Converts DVD to MP3 audio. Supports Dolby, DTS Surround audio track. Converts to the latest iPhone, 4th generation iPad nano, nano chromatic, 2nd generation iPad touch, and Apple TV.

  Read the article

• Creating a really public Windows network share

  - by Timur Aydin

  I want to create a shared folder under Windows (actually, Windows XP, Vista, and Win 7) which can be mounted from a linux system without prompting for a username/password. But before attempting this, I first wanted to establish that this works between two Windows 7 machines. So, on machine A (The server that will hold the public share), I created a folder and set its permissions such that Everyone has read/write access. Then I visited Control Panel - Network and Sharing Center - Advanced Sharing Settings and then selected "Turn off password protected sharing". Then, on machine B (The client that wants to access the public share with no username/password prompt), I tried to "map network driver" and I was immediately prompted by a password prompt. Some search on google suggested changing "Acconts: Limit local account use of blank passwords to console logon only" to "Disabled". Tried that, no luck, still getting username/password prompt. If I enter the username/password, I am not prompted for it again and can use the share as long as the session is active. But still, I really need to access the share without any username/password transaction whatsoever and this is not just a convenience related thing. Here is the actual reason: The device that will access this windows network share is an embedded system running uclinux. It will mount this share locally and then play media files. Its only user interface is a javascript based web page. So, if there is going to be any username/password transaction, I would have to ask the user to enter them over the web page, which will be ridiculously insecure and completely exposed to packet sniffing. After hours of doing experiments, I have found one way to make this happen, but I am not really very fond of it... I first create a new user (shareuser) and give it a password (sharepass). Then I open Group Policy Editor and set "Deny log on locally" to "A\shareuser". Then, I create a folder on A and share it so that shareuser has Read access to it. This way, shareuser cannot login to A, but can access the shared folder. And, if someone discovers the shareuser/sharepass through network sniffing, they can just access the shared folder, but can't logon to A. The same thing can be achieved by enabling the Guest user and then going to Group Policy Editor and deleting the "Guest" from the "Deny access to this computer from the network" setting. Again, Guest can mount the public share, but logging in to A as Guest won't be possible, because Guest is already not allowed to log in by default. So my question would be, how can I create a network share that is truly public, so that it can be mounted from a linux machine without requiring a password? Sorry for the long question, but I wanted to explain the reason for really needing this...

  Read the article

• "log on as a batch job" user rights removed by what GPO?

  - by LarsH

  I am not much of a server administrator, but get my feet wet when I have to. Right now I'm running some COTS software on a Windows 2008 Server machine. The software installer creates a few user accounts for running its processes, and then gives those users the right to "log on as a batch job". Every so often (e.g. yesterday at 2:52pm and this morning at 7:50am), those rights disappear. The software then stops working. I can verify that the user rights are gone by using secedit /export /cfg e:\temp\uraExp.inf /areas USER_RIGHTS and I have a script that does this every 30 seconds and logs the results with a timestamp, so I know when the rights disappear. What I see from the export is that in the "good" state, i.e. after I install the software and it's working correctly, the line for SeBatchLogonRight from the secedit export includes the user accounts created by the software. But every few hours (sometimes more), those user accounts are removed from that line. The same thing can be seen by using the GUI tool Local Security Policy > Security Settings > Local Policies > User Rights Assignment > Log on as a batch job: in the "good" state, that policy includes the needed user accounts, and in the bad state, the policy does not. Based on the above-mentioned logging script and the timestamps at which the user rights are being removed, I can see clearly that some GPOs are causing the change. The GPO Operational log shows GPOs being processed at exactly the right times. E.g.: Starting Registry Extension Processing. List of applicable GPOs: (Changes were detected.) Local Group Policy I have run GPOs on demand using gpupdate /force, and was able to verify that this caused the User Rights to be removed. We have looked over local group policies till our eyes are crossed, trying to figure out which one might be stripping these User Rights to "log on as a batch job." We have not configured any local group policies on this machine, that we know of; so is there a default local group policy that might typically do such a thing? Are there typical domain policies that would do this? I have been working with our IT staff colleagues to troubleshoot the problem, but none of them are really GPO experts... They wear many hats, and they do what they need to do in order to keep most things running. Any suggestions would be greatly appreciated!

  Read the article

• Wifi randomly drops on Windows 8 laptop

  - by JosiahS

  First of all, I did a lot of research on this problem, and I wasn't able to come to any helpful conclusion. I've finally decided that I need advice from those who might know where to look. So don't let me down. :P I used to have an older Windows 7 laptop, which worked great for basic office and web browsing. However, I wanted something that would play actual modern games. So I recently bought a Sager NP8235 with the Intel Wireless-AC 7260 wifi card, and installed Windows 8 Pro on it. And ever since, I've been having problems with the wifi. Generally, what happens is if I leave the laptop on but inactive for an extended amount of time (I've estimated it around an hour to two), the wifi will start dropping randomly. If I happened to have a download going at the time, it usually causes the download to fail. Or, if I put the laptop to sleep overnight, the next morning I usually have to restart the computer because the wifi device apparently stops working (it literally won't turn on). Also, and most frustrating, whenever I'm on a video chat (like Skype), after about ten minutes, the connection will start lagging like crazy, until it forces Skype to end the call. After that, I usually have to disable and reenable the wifi to get it working again. I know it isn't our internet, because all the other computers in our house (~8) don't have any issues. Even the old Windows 7 laptop (connected also over wifi) works just fine, scoring the normal ~3Mbps average on speedtest.net (yes, I know our internet is slow, we live out in the country). Additionally, when I connect the Sager directly to the router via ethernet, the internet instantly starts working just great. Like I said, I've done a lot of googling to figure out what's going on, and I haven't been able to find anything that worked for me. Is it Windows 8 conflicting with the Wifi drivers? As of this writing, I have the Intel drivers v16.1.5.2 installed (without the extra Intel software). Or is it our router? It's a TP-Link TL-WR841ND, set to the default settings. The Sager is currently being assigned to a static IP, if that makes any difference. And yet, the old windows 7 laptop has a much more stable connection than the Sager. Anyone have any ideas? At this point, I'd appreciate even knowing what the problem is.

  Read the article

• Windows7 issue in mutli- tasking and memory

  - by Nitesh

  I seeming some problem in my windows OS recently, let me first say my system configuration. processor - Intel(R) Core(TM)2 Quad CPU Q8400 @ 2.66 GHz Installed memory (RAM) - 4.00 GB (3.00 GB usable) System type - 32 bit operating system I am using two OS in this system, first one is Windows7 and the other is centOS. Well, I am using this from a long time there was no problem , and all of a sudden since from couple weeks I am facing problems in my Windows7 OS. In windows7 i was nearing using multiple jobs almost every time i log in, there was no problem but now i don't no what happen I am not able to do multiple jobs at same time. For example- 1 I am now not able to listen to music in windows media player and view photo's. All of a sudden the system stops working and does not respond and then respond after 5mins and the music get played where it got stopped after 5 mins. 2 When i start browersing internet it hangs all of sudden and doesn't respond for 2 or 3 mins and gets loading. I mean it just happens for every operation i do in the system. Even now typing was also difficult, it gets hanged very frequently even though i am doing single task. I have never come across this kind of problem before. So the first thing i did was to see the useage of the processor and the memory. Well, i thick the useage of the processor was fine, for single task the useage was some where around 3 to 5%. Well, it was something weird i found in the memory, in spite of no task that i was running it was using somewhere around 34 to 41% of memory. So i opened the task manager and click on resource monitor in performance tab. And in the memory section of the monitoring tool i found the usage of my RAM, it was something like this. Hardware reserved - 1029 MB In Use - 1430 MB Modified - 49 MB Standby - 1566 MB free - 22 MB And i could also see Available 1588 MB Cached 1615 MB Total 3067 MB Installed 4096 MB well, this if all i could find out and i have no idea why my computer is acting so weird all of a sudden and the performance problem is growing day by day and i also don't know if there is problem in Bios, i have let it for default settings from long time. please help me and Thank you in advance for reading this and helping me.

  Read the article

• Primary/secondary ethernet interfaces via NetworkManager in Ubuntu 9.10

  - by Josh

  I have an Ubuntu 9.10 machine with three ethernet interfaces, eth0, eth1 and eth2. eth2 is connected to a private network. eth0 and eth2 are connected to two different LANs. Either one will provide access to the internet. All three networks have DHCP servers. Using Ubuntu's the default settings (And Gnome), when I boot up all the interfaces are active and my system gets three IP addresses. However any attempt to access the internet results in connection timeouts and other weirdness. I suspect that traffic is going out on one NIC (like eth0) and coming back in on another (like eth1). I'm not sure what's going on. The only way I can access the internet at the moment is to bring two of the devices down with ifdown. How can I configure eth0 as my primary interface so all trafic goes out by default on that interface, while keeping the other two active? Also, I want to make sure Avahi broadcasts properly on all three IPs so that the computers on the LAN of eth1 can still connect to myHostname.local... EDIT: Here's my routing table: Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 172.16.151.0 0.0.0.0 255.255.255.0 U 0 0 0 eth2 172.16.30.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.1.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 0.0.0.0 172.16.30.2 0.0.0.0 UG 0 0 0 eth0 0.0.0.0 10.1.0.1 0.0.0.0 UG 0 0 0 eth1 I want the 172.16.30.2 network to be the primary one and the 10.1.0.0 network to be the secondary one. EDIT2: My nameservers are also incorrect. It seems like Ubuntu is bringing the networks up in order, eth0, then 1, then 2, and the DHCP information from eth1 is overriding eth0, and eth2 is overriding eth1. How can I reverse this so the DHCP information from eth0 is the "master"? EDIT3: This seems to be an issue with Gnome's NetworkManager.

  Read the article

• How should I use my new SSD drive?

  - by jasondavis

  I just built a new PC the other day. Specs... Processor: Intel i7-930 quad core CPU CPU Cooler: COOLER MASTER Hyper 212 Motherboard: AsRock X58 Extreme 3 RAM/Memory: 6gb G-Skill tripple channel DDR3 memory (3 sticks of 2gb planning to get another kit to make it 12gb total soon) Operating System Hard drive: Intel X25-M 80GB Mainstream SATA2 Solid State Drive Video Cards: 2 XFX ATI Redeon HD 4650 cards to run 3-4 monitors Case: Lian Li PC-B10 Midtower case Power Supply: Antec TruePower New TP-750 Blue 750W Operating System Windows 7 Pro 64bit Not sure if the specs are helpful at all but I posted them just in case. So I got everything put together and running great so far but I need some advice/ideas/help/tips. I got the SSD drive in hopes of using it strictly for my windows 7 install along with all my other programs I install. I am then going to get another drive or 2 just for data (video,music,photos, etc). So my plan is to just install the new data drives and then in windows 7 I will change my "My documents" "My Music" "My Video" "MY Photos" library's to be located on the data drives instead of the OS SSD drive. I would ultimately like to install all my programs with my windows install on the SSD drive and then create an IMAGE of the drive and then 6 months down the road if things are sluggish I can just wipe the drive and restore my IMAGE with all my programs and settings in tact still. So here are some questions now. 1) How can I verify that TRIM is working on my new SSD? 2) Is there anything above that I missed that I should be doing? I think I once read that there is a page file or some sort of file that windows changes a lot and that it should be moved off f an SSD an onto my data drives. DOes anyone know what I might of heard? If you do can you explain the pros and cons of doing such a thing as well as how to possibly? 3) Any tips or advice to get the best performance from all this, I built a pretty nice system and I just want to make it stay that way as long as I can.

  Read the article

• Proxy Error 502 "Reason: Error reading from remote server" with Apache 2.2.3 (Debian) mod_proxy and Jetty 6.1.18

  - by Martin

  Apache is receiving requests at port :80 and proxying them to Jetty at port :8080 The proxy server received an invalid response from an upstream server The proxy server could not handle the request GET /. My dilemma: Everything works fine normally (fast requests, few seconds or few tens of seconds long requests are processed ok). Problems occur when request processing takes long (few minutes?). If I issue request instead directly to Jetty at port :8080 the request is processed OK. So problem is likely to sit somewhere between Apache and Jetty where I am using mod_proxy. How to solve this? I have already tried some "tricks" related to KeepAlive settings, without luck. Here is my current configuration, any suggestions? #keepalive Off ## I have tried this, does not help #SetEnv force-proxy-request-1.0 1 ## I have tried this, does not help #SetEnv proxy-nokeepalive 1 ## I have tried this, does not help #SetEnv proxy-initial-not-pooled 1 ## I have tried this, does not help KeepAlive 20 ## I have tried this, does not help KeepAliveTimeout 600 ## I have tried this, does not help ProxyTimeout 600 ## I have tried this, does not help NameVirtualHost *:80 <VirtualHost _default_:80> ServerAdmin [email protected] ServerName www.mydomain.fi ServerAlias mydomain.fi mydomain.com mydomain www.mydomain.com ProxyRequests On ProxyVia On <Proxy *> Order deny,allow Allow from all </Proxy> ProxyRequests Off ProxyPass / http://www.mydomain.fi:8080/ retry=1 acquire=3000 timeout=600 ProxyPassReverse / http://www.mydomain.fi:8080/ RewriteEngine On RewriteCond %{SERVER_NAME} !^www\.mydomain\.fi RewriteRule /(.*) http://www.mydomain.fi/$1 [redirect=301L] ErrorLog /var/log/apache2/error.log # Possible values include: debug, info, notice, warn, error, crit, # alert, emerg. LogLevel warn CustomLog /var/log/apache2/access.log combined ServerSignature On </VirtualHost> Here is also the debug log from a failing request: 74.125.43.99 - - [29/Sep/2010:20:15:40 +0300] "GET /?wicket:bookmarkablePage=newWindow:com.mydomain.view.application.reports.SaveReportPage HTTP/1.1" 502 355 "https://www.mydomain.fi/?wicket:interface=:0:2:::" "Mozilla/5.0 (Windows; U; Windows NT 6.1; fi; rv:1.9.2.10) Gecko/20100914 Firefox/3.6.10" [Wed Sep 29 20:20:40 2010] [error] [client 74.125.43.99] proxy: error reading status line from remote server www.mydomain.fi, referer: https://www.mydomain.fi/?wicket:interface=:0:2::: [Wed Sep 29 20:20:40 2010] [error] [client 74.125.43.99] proxy: Error reading from remote server returned by /, referer: https://www.mydomain.fi/?wicket:interface=:0:2:::

  Read the article

• Why Does My Windows 7 PC Freeze After Waking from Sleep?

  - by Blaenk

  Hey guys. I have Windows 7 running on my computer and everything is perfect. There's only one little problem. Sometimes when I leave my computer, I come back and my monitor is turned off or asleep, whichever it is. This is fine, I set it to do this. However, after turning on the monitor and moving the mouse around, the mouse cursor freezes; both the keyboard and mouse don't respond to anything, for example the keyboard's windows key won't bring up the start menu and moving the mouse around does not move the cursor around on the screen. I have to wait about a minute or two before things start working again. I figured this was a power savings setting problem, so I went into Control Panel Power Options. I only have Turn off Display = 30 minutes and Put Computer to Sleep = Never. Of course, I went into the advanced power settings to look through there. I put Never to turn off the hard disk, Sleep after never, and that's about it. Nothing else there looks like it might be causing this. I went into the device manager and checked the mouse and the keyboard, and they both have the Allow this device to wake the computer checked for both of them. Perhaps this other bit of information might help: Sometimes I VNC into my PC using my MacBook, and sometimes, as soon as it shows me the desktop, the same thing happens. The mouse won't move and VNC won't register any events on the server (Which is my PC of course). I close the client (And I know it has nothing to do with the client), then immediately restart it and try to connect. When I click the connect button, it hangs there, as if the PC is not responding. Basically it's like whenever I try to wake the computer from sleep, it does so by showing me the desktop, then it freaks out. Then again, I guess the computer isn't sleeping because the setting is set to 'Sleep after = Never'. I honestly don't know what's going on, would appreciate any insight. Thanks!

  Read the article

• VPN Connection Causes Internal LAN Connection Loss with Server

  - by sleepisfortheweak

  I've tried configuring basic PPTP VPN at my small business using a number of different tutorials. As far as I can tell, the actual VPN connection worked fine, but upon connecting a client, the Server 'disappears' from the internal LAN. The RRAS service must be stopped before the connection is restored. My Setup: The network is simply a DSL Gateway/Router to the outside functioning as NAT/Firewall/DHCP. The server is a Win Server 2008 machine at fixed IP 192.168.1.200. The server has 1 NIC, so I used the 'custom' option when configuring RRAS. The RRAS settings should be default except that I've disabled ports for connection types I'm not using and reduced PPTP ports to 10. I've also created an address pool and disabled DHCP packet forwarding. The server only functions as a File Share and now a VPN Server. Local LAN computers all have mapped network shares to the server authenticated based on Local User/Group setup on the server. The Problem: The moment a client connects through VPN, the server 'disappears' from the local network. All mapped drives disconnect and there is no response to a ping 192.168.1.200. Even if the client disconnects, the server does not re-appear at that address until the RRAS service is stopped. I've Tried: Using an Address Pool inside and outside the local subnet. Using DCHP Relay Checking Inbound/Outbound filters (none enabled) The fact that nothing I've tried has had any effect, and that I can connect and successfully obtain an IP tells me that it's something more fundamental I'm missing. My gut tells me that it's something to do with the second IP address added by the VPN client somehow taking over the interface or traffic from the local LAN accidently getting routed to the VPN client instead of handled at the server once RRAS has become 'active' when a client connects. Hopefully this may be obvious to someone with real IT experience. I've been doing this a while and almost never been stumped. I'm starting to think it might actually be something tricky since my setup is pretty basic yet refuses to work. I'll be happy to include more info if this doesn't ring any bells right away for anyone. Thanks

  Read the article

< Previous Page | 542 543 544 545 546 547 548 549 550 551 552 553  | Next Page >