Search Results

Search found 14326 results on 574 pages for 'office for mac'.

Page 547/574 | < Previous Page | 543 544 545 546 547 548 549 550 551 552 553 554  | Next Page >

• Setting up a fileserver, some questions?

  - by Tanax

  Recently I've become very interested in setting up a fileserver, mostly for home usage but also because of the fact that I live in 2 places, I need to be able to access my files from both homes. I have already done some research into this but I am unclear about some things. My requirements are the following; Needs to work on both Mac and PC(only using Windows atm on PC but could be good if it supports more OS's to make it futureproof in case I need Linux or something else) Need to be able to set up a folder/drive/network space to act as a link to a certain folder on the fileserver All files should only be stored on the fileserver, e.g. no "shared" folders like in Dropbox where files are stored on the client computer Would prefer it if folders are password protected or that I can somehow specify what users can access the fileserver's shares Fileserver's OS most likely have to be Windows due to other factors outside of being just a fileserver I've already kinda figured out that I will need to set up a VPN so that I can access my fileserver from outside the local network. Probably going to use OpenVPN. Question 1: How would I go about to set up a VPN server so that I can connect to my local network at the fileserver's location? I know that since I'm on a dynamic IP I will have to get some sort of dynamic DNS server - I've already checked into this and I'm fairly sure I know how to fix that. I also know that I will have to forward the port OpenVPN uses in my router. Question 2: How would I actually share the folders on the fileserver so that I can access them on my other computers? I've researched into Samba but I'm uncertain if it needs to be run on a Linux OS. I know that the clients connecting to it can be Windows for example but can the Samba "server" be run on Windows? Also it appears that Samba shares a folder, meaning it works like Dropbox - I don't want that. So how would I share a folder in that case to make it work like I want it to? Sorry for the incredibly long question, I tried to structure it the best I could for easier read. Thanks in advance!

  Read the article

• Setting up a fileserver, some questions?

  - by Tanax

  Recently I've become very interested in setting up a fileserver, mostly for home usage but also because of the fact that I live in 2 places, I need to be able to access my files from both homes. I have already done some research into this but I am unclear about some things. My requirements are the following; Needs to work on both Mac and PC(only using Windows atm on PC but could be good if it supports more OS's to make it futureproof in case I need Linux or something else) Need to be able to set up a folder/drive/network space to act as a link to a certain folder on the fileserver All files should only be stored on the fileserver, e.g. no "shared" folders like in Dropbox where files are stored on the client computer Would prefer it if folders are password protected or that I can somehow specify what users can access the fileserver's shares Fileserver's OS most likely have to be Windows due to other factors outside of being just a fileserver I've already kinda figured out that I will need to set up a VPN so that I can access my fileserver from outside the local network. Probably going to use OpenVPN. Question 1: How would I go about to set up a VPN server so that I can connect to my local network at the fileserver's location? I know that since I'm on a dynamic IP I will have to get some sort of dynamic DNS server - I've already checked into this and I'm fairly sure I know how to fix that. I also know that I will have to forward the port OpenVPN uses in my router. Question 2: How would I actually share the folders on the fileserver so that I can access them on my other computers? I've researched into Samba but I'm uncertain if it needs to be run on a Linux OS. I know that the clients connecting to it can be Windows for example but can the Samba "server" be run on Windows? Also it appears that Samba shares a folder, meaning it works like Dropbox - I don't want that. So how would I share a folder in that case to make it work like I want it to? Sorry for the incredibly long question, I tried to structure it the best I could for easier read. Thanks in advance!

  Read the article

• libvirt qemu/kvm migration problem

  - by Panda

  I am using kvm and libvirt on my Dell server. Now i am trying to migrate one virtual machine from a physical server to another. However, I failed everytime. In virsh on physicalServer1, I typed: virsh # migrate virtualmachine1 qemu+ssh://username@physicalServer2/system error: operation failed: migration to 'tcp:physicalServer2:49163' failed: migration failed Then I searched FAQ part on libvirt.org. It says: error: operation failed: migration to '...' failed: migration failed This is an error often encountered when trying to migrate with QEMU/KVM. This typically happens with plain migration, when the source VM cannot connect to the destination host. You will want to make sure your hosts are properly configured for migration (see the migration section of this FAQ) I managed to ssh physicalServer2 from a shell on virtualmachine1 so the above red part did not explain my failure. I also open ports on physicalServer2, iptables -L shows following information: Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT udp -- anywhere anywhere udp dpt:domain ACCEPT tcp -- anywhere anywhere tcp dpt:domain ACCEPT udp -- anywhere anywhere udp dpt:bootps ACCEPT tcp -- anywhere anywhere tcp dpt:bootps ACCEPT udp -- anywhere anywhere udp dpt:domain ACCEPT tcp -- anywhere anywhere tcp dpt:domain ACCEPT udp -- anywhere anywhere udp dpt:bootps ACCEPT tcp -- anywhere anywhere tcp dpt:bootps ACCEPT tcp -- anywhere anywhere state NEW tcp dpts:49152:49215 Chain FORWARD (policy ACCEPT) target prot opt source destination ACCEPT all -- anywhere 192.168.122.0/24 state RELATED,ESTABLISHED ACCEPT all -- 192.168.122.0/24 anywhere ACCEPT all -- anywhere anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable REJECT all -- anywhere anywhere reject-with icmp-port-unreachable ACCEPT all -- anywhere 192.168.122.0/24 state RELATED,ESTABLISHED ACCEPT all -- 192.168.122.0/24 anywhere ACCEPT all -- anywhere anywhere REJECT all -- anywhere anywhere reject-with icmp-port-unreachable REJECT all -- anywhere anywhere reject-with icmp-port-unreachable Chain OUTPUT (policy ACCEPT) target prot opt source destination The /var/log/libvirt/qemu/virtualmachine1.log on physicalServer2: 2011-05-06 13:37:30.708: starting up LC_ALL=C PATH=/usr/local/sbin:/usr/local/bin:/usr/bin:/usr/sbin:/sbin:/bin QEMU_AUDIO_DRV=none /usr/bin/kvm -S -M pc-0.14 -enable-kvm -m 2048 -smp 1,sockets=1,cores=1,threads=1 -name openjudge-test -uuid a8c704bc-a4f9-90db-3e57-40e60b00aac1 -nodefconfig -nodefaults -chardev socket,id=charmonitor,path=/var/lib/libvirt/qemu/virtualmachine1.monitor,server,nowait -mon chardev=charmonitor,id=monitor,mode=readline -rtc base=utc -boot c -drive file=/media/nfs/virtualmachine1.img,if=none,id=drive-ide0-0-0,format=raw -device ide-drive,bus=ide.0,unit=0,drive=drive-ide0-0-0,id=ide0-0-0 -drive if=none,media=cdrom,id=drive-ide0-1-0,readonly=on,format=raw -device ide-drive,bus=ide.1,unit=0,drive=drive-ide0-1-0,id=ide0-1-0 -netdev tap,fd=20,id=hostnet0 -device rtl8139,netdev=hostnet0,id=net0,mac=00:16:36:8a:22 :a0,bus=pci.0,addr=0x3 -chardev pty,id=charserial0 -device isa-serial,chardev=charserial0,id=serial0 -usb -vnc 127.0.0.1:2 -vga cirrus -incoming tcp:0.0.0.0:49163 -device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x4 char device redirected to /dev/pts/0 2011-05-06 13:37:30.915: shutting down The /var/log/libvirt/qemu/virtualmachine1.log on physicalServer1 is empty. Both physical servers are using Ubuntu 11.04. The libvirt and kvm used are installed by apt-get. The libvirt version is 0.8.8.

  Read the article

• creating a heirarchy of terminals or workspaces

  - by intuited

  <rant This question occurred to me ('occurred' meaning 'whispered seductively in my ear for the 100th time') while using GNU-screen, so I'll make that my example. However this is a much more general question about user interfaces and what I perceive as a flawmissing feature in every implementation I've yet seen. I'm wondering if there is some way to create a heirarchy/tree of terminals in a screen session. EG I'd like to have something like 1 bash 1.1 bash 1.2 bash 2 bash 3 bash 3.1 bash 3.1.1 bash 3.1.2 bash It would be good if the terminals could be labelled instead of having to be navigated to via some arrangement that I suspect doesn't exist. So then you could jump to one using eg ^A:goto happydays or ^A:goto dykstra.angry. So to generalize that: Firefox, Chrome, Internet Explorer, gnome-terminal, roxterm, konsole, yakuake, OpenOffice, Microsoft Office, Mr. Snuffaluppagus's Funtime Carousel™, and Your Mom's Jam Browser™ all offer the ability to create a flat set of tabs containing documents of an identical nature: web pages, terminals, documents, fun rideable animals, and jams. GNU-screen implements the same functionality without using tabs. Linux and OS/X window managers provide the ability to organize windows into an array of workspaces, which amounts to again, the same deal. Over the past few years, this has become a more or less ubiquitous concept which has been righteously welcomed into the far reaches of the computer interface funfest. Heavy users of these systems quickly encounter a problem with it: the set of entities is flat. In the case of workspaces, an option may be available to create a 2d array. However none of these applications furnish their users with the ability to create heirarchies, similar to filesystem directory structures, containing instances of their particular contained type. I for one am consistently bothered by this, and am wondering if the community can offer some wisdom as to why this has not happened in any of the foremost collections of computational functionality our culture has yet produced. Or if perhaps it has and I'm just an ignorant savage. I'd like to be able to not only group things into a tree structure, but also to create references (aka symbolic links, aka pointers) from one part of the structure to another, as well as apply properties (eg default directory, colorscheme, ...) recursively downward from a given node. I see no reason why we shouldn't be able to save these structures as known sessions, and apply tags to particular instances. So then you can sort through them by tag, find them by name, or just use the arrow keys (with an appropriate modifier) to move left or right and in or out of a given level. Another key combo would serve to create a branch in the place of the current terminal/webpage/lifelike statue/spreadsheet/spreadsheet sheet/presentation/jam and move that entity into the new branch, then create a fresh one as a sibling to it: a second leaf node within the same branch node. They would get along well. I find it a bit astonishing that this hasn't happened yet, and the only reason I can venture as a guess is that the creators of these fine systems do not consider such functionality to be useful to a significant portion of their userbase. I posit that the probability that that such an assumption would be correct is pretty low. On the other hand, given the relative ease with which such structures can be implemented using modern libraries/languages, it doesn't seem likely that difficulty of implementation would be a major roadblock. If it could be done in 1972 or whenever within the constraints of a filesystem driver, it should be relatively painless to implement in 2010 in a fullblown application. Given that all of these systems are capable of maintaining a set of equivalent entities, it seems unlikely that a major infrastructure overhaul would be necessary in order to enable a navigable heirarchy of them. </rant Mostly I'm just looking to start up a discussion and/or brainstorming on this topic. Any ideas, examples, criticism, or analysis are quite welcome. * Mr. Snuffaluppagus's Funtime Carousel is a registered trademark of Children's Television Workshop Inc. * Your Mom's Jam Browser is a registered trademark of Your Mom Inc.

  Read the article

• iPhone 3.1 Black Screen

  - by churnd

  Since I've updated my 3G iPhone to 3.1, it will become unresponsive after ~4-5 hours. It looks like it's off, but it's not. None of the buttons do anything that I can see. The only way I can get a screen back is to do a hard reset (Power + Home). Has anyone else had this problem? What can I do to fix it? I've had it 3 happen 3 times already. Very annoying. Apparently, the Discussions forum on Apple.com also shows lots of people are having the same problem. One guy said he did a restore and that fixed it for him, which I haven't tried yet because many others also tried that and it didn't help. A few others have said turning off WIFI fixes it for them, so I'm going to try that today. Another thing I've noticed is that now, when I plug in my iPhone to my Macbook Pro, iTunes 9 does not launch. It used to before the update. ** Further update and possible solution ** I left my iPhone plugged into my Macbook Pro yesterday while at work, and didn't use it much throughout the day. I noticed it didn't lock up once. I suspect this was because it was connected to a power source. I continued to use my iPhone with no problem yesterday and today. Still no lockups as of now. I personally think this was Spotlight and/or Genius "doing it's thing" from a new install. Kinda like an OS upgrade on your Mac... Spotlight has to rebuild itself and those first couple of hours can be kinda sluggish. This would be even more so on the iPhone where processing power is limited, and I'm sure the processor is clocked down a bit while on battery power, which would further amplify the problem. Again, just my guess. My iPhone is working fine now. ** Final Solution ** Update to 3.1.2. Problem solved.

  Read the article

• How to iptables forward ppp0 to eth0

  - by HPHPHP2012

  need your help with get it routing properly. I've server with eth0 (external interface) and eth1(internal interface). eth1 is merged into the bridge br0 (172.16.1.1) I've installed the pptp and successfully configured it, so I got ppp0 interface (192.168.91.1) and got my VPN clients successfully connected. So I need your help to manage how to allow my VPN clients use internet connection (eth0). Below my configuration files, any help is much appreciated! Thank you! P.S. VPN clients are Windows Xp, Windows 7, Mac OS X Lion, Ubuntu 12.04, iOS 5.x cat /etc/pptpd.conf #local server ip address localip 192.168.91.1 #remote addresses remoteip 192.168.91.11-254,192.168.91.10 #translating ip addresses on this interface bcrelay br0 cat /etc/ppp/pptpd-options name pptpd refuse-pap refuse-chap refuse-mschap require-mschap-v2 require-mppe-128 ms-dns 8.8.8.8 ms-dns 8.8.4.4 nodefaultroute lock nobsdcomp auth logfile /var/log/pptpd.log cat /etc/nat-up #!/bin/sh SERVER_IP="aaa.aaa.aaa.aaa" LOCAL_IP="172.16.1.1" #eth0 with public ip PUBLIC="eth0" #br0 is internal bridge on eth1 interface INTERNAL="br0" #vpn VPN="ppp0" #local LOCAL="lo" iptables -F iptables -X iptables -t nat -F iptables -t nat -X iptables -t mangle -F iptables -t mangle -X iptables -P INPUT DROP iptables -P FORWARD DROP iptables -P OUTPUT ACCEPT echo 1 > /proc/sys/net/ipv4/ip_forward iptables -A INPUT -i $LOCAL -j ACCEPT iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A INPUT -m state --state NEW ! -i $PUBLIC -j ACCEPT ####CLEAR CONFIG#### #iptables -A FORWARD -i $PUBLIC -o $INTERNAL -m state --state ESTABLISHED,RELATED -j ACCEPT #iptables -A FORWARD -i $PUBLIC -o $INTERNAL -j ACCEPT #iptables -A FORWARD -i $INTERNAL -o $PUBLIC -j ACCEPT #iptables -t nat -A POSTROUTING -j MASQUERADE ####THIS PART IS NOT HANDLING IT#### iptables -A FORWARD -i $PUBLIC -o $VPN -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A FORWARD -i $PUBLIC -o $VPN -j ACCEPT iptables -A FORWARD -s 192.168.91.0/24 -o $PUBLIC -j ACCEPT iptables -t nat -A POSTROUTING -s 192.168.91.0/24 -o $PUBLIC -j MASQUERADE # VPN - PPTPD iptables -A INPUT -p gre -s 0/0 -j ACCEPT iptables -A OUTPUT -p gre -m state --state RELATED,ESTABLISHED -j ACCEPT iptables -A INPUT -p tcp -s 0/0 --dport 1723 -j ACCEPT #SSH iptables -A INPUT -p tcp --dport 2222 -j ACCEPT iptables -A OUTPUT -p tcp --sport 2222 -j ACCEPT #BLACKLIST BLOCKDB="/etc/ip.blocked" IPS=$(grep -Ev "^#" $BLOCKDB) for i in $IPS do iptables -A INPUT -s $i -j DROP iptables -A OUTPUT -d $i -j DROP done

  Read the article

• Issue with Netgear GS108T Managed Switch and Jumbo Frames

  - by Richie086

  I recently purchased a Netgear GS108T managed switch and I am trying to configure jumbo packets between my NAS (Thecus N4100Pro), PC and managed switch. I should mention the fact that I was able to use jumbo frames between my PC and NAS before I purchased the switch without issue. My Desktop has a wired gigabit NIC (Intel 82579V Gigabit) and has the ability to configure jumbo frames (see pic) that are either 9014 bytes or 4088 bytes. I choose 9014 bytes for the jumbo frame size My NAS supports jumbo frames as well, and is configured to use 9014 as the frame size. When I go into my Netgear managed switch and set the frame size to 9014 on the ports I am using for my PC and NAS. See image As soon as I hit apply in the web interface, I loose my connection to the SMB shares on my NAS and I can no longer connect to the web admin interface for my NAS. The really strange thing is I can ping my NAS via the ping command, but when I try to connect to the web interface on port 80 or port 443 the page never loads. I did a scan from my PC to my NAS using nmap and I can see the following ports open PORT STATE SERVICE 22/tcp open ssh 80/tcp open http 111/tcp open rpcbind 139/tcp open netbios-ssn 443/tcp open https 445/tcp open microsoft-ds 631/tcp open ipp 2000/tcp open cisco-sccp 2049/tcp open nfs 3260/tcp open iscsi 49152/tcp open unknown MAC Address: 00:14:FD:15:00:44 (Thecus Technology) Read data files from: C:\Program Files (x86)\Nmap Nmap done: 1 IP address (1 host up) scanned in 211.97 seconds Raw packets sent: 1 (28B) | Rcvd: 1 (28B) Anyone have any idea what is going on here? Why is nmap able to detect the ports are open and listening for http, https and file sharing but I cant connect when all devices have jumbo packets enabled? Stranger still - I did a packet capture using wireshark while the nmap scan was running and filtered so I only saw converstations between my PC and my NAS. Here are the packet details from my scan Only 4 packets over 5k bytes? What is going on here? Do I not need to configure jumbo frame sizes on the switch? I have an internet connection from my pc to the switch to my router - I just cannot connect to my NAS. I just checked on my iPhone and I am able to open my NAS web admin interface without issue on my iPhone! WTF!!!!!! Let me know if you need more details..

  Read the article

• Profiles and using the local profile for a domain user

  - by Harry

  I’m having some trouble with profiles and would like to reach out for some help. I’ve tried to do some research to help myself along, but I’m not making much progress on my own. I’ve pretty much taken over the sys admin duties for my small lab, I don’t have much experience to justify it besides I’m the only with the time and dedication to go at it (The environment was in a state of disrepair). My network and domain I look over are extremely small by most standards, about 10 users at a time. They are pretty intensive activity on the network, and we do work with fairly large files. None of the network is online, which is nice at the moment because it allows me not to have another headache. On to my profile problem, I have set up roaming profiles for the users in the network. Now after a little research, I think I will be switching this to a hybrid of folder redirection and roaming profiles as this seems to best practice. I also don’t want the users having to wait for a long time if they have a bloated profile. Now I’ve finally got a build working using MDT. We have Mac Pros, and it wasn’t fun getting everything to play nice. The way I did this was by setting up a reference computer and installing all the software and tools that each user would need and editing the settings preferences to how we would need them. I think used MDT to do a sys prep and capture to create the image of my reference computer. Using the reference image I can push out my images to the rest of the desktops in my environment. The issue I’m having is when we join the computer to domain. The user can login and operate fine on the computer, but I’d like a more. When the user is logged on with their domain user name they lose a lot of the icons I had on my reference image, as well as the desktop background and some other miscellaneous settings. I would love to have the user log on using their domain user name and see the icons and desktop environment as I had it setup on the reference computer. I’m not sure if it is possible, or something simple that I’m missing, but any help would be greatly appreciated!

  Read the article

• getting Internet connection sharing working in a slightly more complicated configuration

  - by tirichitirca t

  I have the following configuration: Computer A - Mac OSX 10.8.4, wireless & wired adapters Computer B - Windows 7 (64 bit), wireless & wired adapters, has internet connection via the wired adapter (ethernet) d-link wired/wireless router. Problem to solve: Connect from computer A to the internet through the wired connection of computer B. I tried the following: I set up a local network between A and B using the d-link router. The configuration is this: D-link router - 192.168.0.1 A - wired connection to the d-link router, static 192.168.0.101 (I could have used the wireless but I preferred the wired connection) B - wireless connection to the d-link router DHCP 192.168.0.102 (but I made sure it always gets the same address) B - wired connection to the internet using some address that begins with 10.x.y.z. In this configuration A can see B. I enabled ICS on the wired adapter of B. I set up the Gateway of A to point to B and DNS servers to point to the DNS servers specified for the 10.x.y.z address. It doesn't work, A goes only as far as B. It can ping the 10.x.y.z address of B though. I then found this article: http://terrybritton.com/windows-internet-connection-sharing-ics-not-working-with-linux-bridging-is-the-solution-916/. Terry is suggesting that a bridge should be defined on B between the two connections. I tried that but basically computer B is screwed as soon as I create the bridge. It can't connect to the internet anymore. It is as if the network bridge seems to think the traffic to the internet should go from the wired connection to the wireless and not the other way around. The other thing that puzzles me is the router itself. In general the router needs an internet address. In a normal configuration it is the router that gets the ip address and the internet traffic goes through the router. In my case I am not interested in that. So, any suggestions to get this working? I wouldn't shy away from using a commercial software but I would think windows 7 should allow me to do it. Thanks

  Read the article

• Postfix on Snow Leopard unable to send MIME emails, including header contents in message body

  - by devvy

  I configured postfix on snow leopard by adding the following line to /etc/hostconfig: MAILSERVER=-YES- I then configured postfix to relay through my ISP's SMTP server. I added the following two lines in their respective places within /etc/postfix/main.cf: myhostname = 1and1.com relayhost = shawmail.vc.shawcable.net I then have a simple PHP mail function wrapper as follows: send_email("[email protected]", "[email protected]", "Test Email", "<p>This is a simple HTML email</p>"); echo "Done"; function send_email($from,$to,$subject,$message){ $header="From: <".$from."> "; $header.= 'MIME-Version: 1.0' . " "; $header.= 'Content-type: text/html; charset=iso-8859-1' . " "; $send_mail=mail($to,$subject,$message,$header); if(!$send_mail){ echo "ERROR"; } } With this, I am receiving an e-mail that appears to be improperly formatted. The message header is showing up in the body of the e-mail. The raw message content is as follows: Return-Path: <[email protected]> Delivery-Date: Tue, 27 Apr 2010 18:12:48 -0400 Received: from idcmail-mo2no.shaw.ca (idcmail-mo2no.shaw.ca [64.59.134.9]) by mx.perfora.net (node=mxus2) with ESMTP (Nemesis) id 0M4XlU-1NCtC81GVY-00z5UN for [email protected]; Tue, 27 Apr 2010 18:12:48 -0400 Message-Id: <[email protected]> Received: from pd6ml3no-ssvc.prod.shaw.ca ([10.0.153.149]) by pd6mo1no-svcs.prod.shaw.ca with ESMTP; 27 Apr 2010 16:12:47 -0600 X-Cloudmark-SP-Filtered: true X-Cloudmark-SP-Result: v=1.0 c=1 a=VphdPIyG4kEA:10 a=hATtCjKilyj9ZF5m5A62ag==:17 a=mC_jT1gcAAAA:8 a=QLyc3QejAAAA:8 a=DGW4GvdtALggLTu6w9AA:9 a=KbDtEDGyCi7QHcNhDYYwsF92SU8A:4 a=uch7kV7NfGgA:10 a=5ZEL1eDBWGAA:10 Received: from unknown (HELO 1and1.com) ([24.84.196.104]) by pd6ml3no-dmz.prod.shaw.ca with ESMTP; 27 Apr 2010 16:12:48 -0600 Received: by 1and1.com (Postfix, from userid 70) id BB08D14ECFC; Tue, 27 Apr 2010 15:12:47 -0700 (PDT) To: [email protected] Subject: Test Email X-PHP-Originating-Script: 501:test.php Date: Tue, 27 Apr 2010 18:12:48 -0400 X-UI-Junk: AutoMaybeJunk +30 (SPA); V01:LYI2BGRt:7TwGx5jxe8cylj5nOTae9JQXYqoWvG2w4ZSfwYCXmHCH/5vVNCE fRD7wNNM86txwLDTO522ZNxyNHhvJUK9d2buMQuAUCMoea2jJHaDdtRgkGxNSkO2 v6svm0LsZikLMqRErHtBCYEWIgxp2bl0W3oA3nIbtfp3li0kta27g/ZjoXcgz5Sw B8lEqWBqKWMSta1mCM+XD/RbWVsjr+LqTKg== Envelope-To: [email protected] From: <[email protected]> MIME-Version: 1.0 Content-type: text/html; charset=iso-8859-1 Message-Id: <[email protected]> Date: Tue, 27 Apr 2010 15:12:47 -0700 (PDT) <p>This is a simple HTML email</p> And here are the contents of my /var/log/mail.log file after sending the email: Apr 27 15:29:01 User-iMac postfix/qmgr[705]: 74B1514EDDF: removed Apr 27 15:29:30 User-iMac postfix/pickup[704]: 25FBC14EDF0: uid=70 from=<_www> Apr 27 15:29:30 User-iMac postfix/master[758]: fatal: open lock file pid/master.pid: unable to set exclusive lock: Resource temporarily unavailable Apr 27 15:29:30 User-iMac postfix/cleanup[745]: 25FBC14EDF0: message-id=<[email protected]> Apr 27 15:29:30 User-iMac postfix/qmgr[705]: 25FBC14EDF0: from=<[email protected]>, size=423, nrcpt=1 (queue active) Apr 27 15:29:30 User-iMac postfix/smtp[747]: 25FBC14EDF0: to=<[email protected]>, relay=shawmail.vc.shawcable.net[64.59.128.135]:25, delay=0.21, delays=0.01/0/0.1/0.1, dsn=2.0.0, status=sent (250 ok: Message 25784419 accepted) Apr 27 15:29:30 User-iMac postfix/qmgr[705]: 25FBC14EDF0: removed Two other people in the office have followed the exact same process and are running the exact same script, version of snow leopard, php, etc. and everything is working fine for them. I've even copied their config files to my machine, restarted postfix, restarted apache, all to no avail. Does anyone know what steps I could take to resolve the issue? This is boggling my mind... Thanks

  Read the article

• OSX: Howto start VirtualBox VM on startup?

  - by snies

  The Question How do i start this Wiki VM at the startup of the OSX Server? I am running OSX Server 10.6.8 and VirtualBox 4.1.8 r75467 and a Debian Linux VM (called "wiki"). . What I tried so far Following this article: http://mikkel.hoegh.org/blog/2010/12/23/run-virtualbox-boot-mac-os-x/, i have wrote this plist and placed it in /Library/LaunchDaemons/bar.foo.WikiVirtualBox.plist: <plist version="1.0"> <dict> <key>Label</key> <string>bar.foo.WikiVirtualBox</string> <key>ProgramArguments</key> <array> <string>/usr/bin/VBoxHeadless</string> <string>-s</string> <string>wiki</string> </array> <key>RunAtLoad</key> <true></true> <key>UserName</key> <string>root</string> <key>WorkingDirectory</key> <string>/var/root</string> <key>StandardErrorPath</key> <string>/var/log/bar.foo.WikiVirtualBox.stderr.log</string> <key>StandardOutPath</key> <string>/var/log/bar.foo.WikiVirtualBox.stdout.log</string> </dict> </plist> and told launchd to start it: sudo launchctl load -w /Library/LaunchDaemons/bar.foo.WikiVirtualBox.plist . The Logfile But the VM doesn't start. A Look at tail -f /var/log/system.log shows: sudo[1909]: administrator : TTY=ttys000 ; PWD=/Users/administrator ; USER=root ; COMMAND=/bin/launchctl load -w /Library/LaunchDaemons/bar.foo.WikiVirtualBox.plist VBoxSVC[1914]: 3891612: (connectAndCheck) Untrusted apps are not allowed to connect to or launch Window Server before login. VBoxSVC[1914]: kCGErrorFailure: Set a breakpoint @ CGErrorBreakpoint() to catch errors as they are logged. com.apple.launchd[1] (bar.foo.WikiVirtualBox[1910]): Exited with exit code: 1 When i log into the server via ssh (so no login window opened) i can run: /usr/bin/VBoxHeadless -s wiki and it works. So i don't understand the error above.

  Read the article

• MacVim, Command-T: SEGV

  - by Ramon Tayag

  Details: OSX 10.7.4 I installed the latest MacVim via Homebrew: $ command-t brew install macvim ==> Downloading https://github.com/b4winckler/macvim/tarball/snapshot-64 Already downloaded: /Library/Caches/Homebrew/macvim-7.3-64.tgz ==> ./configure --with-features=huge --with-tlib=ncurses --enable-multibyte --with-macarchs=x86_64 --enable-perlinterp --enable-pythoninterp --enable-rubyinterp --enable-t ==> make getenvy ==> make ==> Caveats MacVim.app installed to: /usr/local/Cellar/macvim/7.3-64 To link the application to a normal Mac OS X location: brew linkapps or: ln -s /usr/local/Cellar/macvim/7.3-64/MacVim.app /Applications ==> Summary /usr/local/Cellar/macvim/7.3-64: 1733 files, 27M, built in 53 seconds $ command-t brew linkapps Linking /usr/local/Cellar/macvim/7.3-64/MacVim.app Finished linking. Find the links under ~/Applications. $ command-t ruby -v ruby 1.8.7 (2011-12-28 patchlevel 357) [universal-darwin11.0] $ command-t rvm list rvm rubies ree-1.8.7-2012.02 [ i686 ] ruby-1.8.7-p358 [ i686 ] ruby-1.9.2-p290 [ x86_64 ] ruby-1.9.2-p320 [ x86_64 ] ruby-1.9.3-p194 [ x86_64 ] # Default ruby not set. Try 'rvm alias create default <ruby>'. # => - current # =* - current && default # * - default $ command-t cd ~/.vim/bundle/vim-command-t/ruby/command-t ruby extconf.rb $ command-t ruby extconf.rb checking for ruby.h... yes creating Makefile $ command-t make cc -arch i386 -arch x86_64 -pipe -bundle -undefined dynamic_lookup -o ext.bundle ext.o match.o matcher.o -L. -L/System/Library/Frameworks/Ruby.framework/Versions/1.8/usr/lib -L. -arch i386 -arch x86_64 -lruby -lpthread -ldl -lobjc ld: warning: ignoring file ext.o, file was built for unsupported file format which is not the architecture being linked (i386) ld: warning: ignoring file match.o, file was built for unsupported file format which is not the architecture being linked (i386) ld: warning: ignoring file matcher.o, file was built for unsupported file format which is not the architecture being linked (i386) $ command-t mvim MacVim then opens here. But when I open Command-T, MacVim crashes and I see this in the command line: $ command-t dyld: lazy symbol binding failed: Symbol not found: _rb_intern2 Referenced from: /Users/ramon/.vim/bundle/vim-command-t/ruby/command-t/ext.bundle Expected in: flat namespace dyld: Symbol not found: _rb_intern2 Referenced from: /Users/ramon/.vim/bundle/vim-command-t/ruby/command-t/ext.bundle Expected in: flat namespace Vim: Caught deadly signal TRAP Vim: Finished. The problem I have is very similar to this, except that I switched to the system Ruby and still got the error.

  Read the article

• Ubuntu Newbie Needs Assistance!!

  - by Steve Greene

  New Ubuntu User Needs Help!- version 9.10 does not communicate with laptop Hello folks, Several days ago, I installed Ubuntu 9.10 onto my Acer Aspire 3100 laptop, running it alongside Widows Vista as a dual-bootable system. Creation of the Ubuntu boot CD went fine, and the installation onto my hard drive was flawless. Ubuntu opens and behaves as I would expect, except for one little problem. For reasons unknown to me, Ubuntu is not communicating with my laptop's networking hardware, and I have no internet connectivity, even when sitting directly under the wireless router at the local library (literally), which puts out a wickedly-fast signal that my Windows Vista OS auto-detects and immediately connects to. Up in the right side of the Ubuntu desktop, I click on the network icon and it does not show a wireless connection at all, even though I am only a few feet from the router. At home, where I use a dialup modem, I also see no means of getting online. My modem is an HDAUDIO Soft Data Fax Modem with Smart CP,manufactured by CXT (Conexant Systems Inc., file version 4.0.13.0, and the driver version is 7.58.0.0). I desparately wish to convert to Ubuntu. I used Mac for ten years, and then Windows for ten years. Now, after 20 years, I want to live out my days as an open-source Ubuntu fanatic. I am ready to give the old status quo the boot! I am an advanced computer user, but I am not a programmer. I seek a solution that is user-friendly for normal people, something equivalent to a driver that I can easily install or activate that will allow Ubuntu to see my hardware and get me connected. Can anyone help me over this hopefully-little glitch so that I can move on in total Ubuntu bliss? My processor is a Mobile AMD Sempron Processor 3500+ at 1.80 GHz, 1.50 GB RAM, and a 32-bit Operating System. I am running Windows Vista Home Basic, Service Pack 2. My current email is [email protected] if you have a workable solution that does not require programmer status to implement. Surely this must be a simple fix that I simply am overlooking, but being the new guy on the block, I have yet to be enlightened. Thanks for your help in coming up to speed!! Steve Wanna' be Ubuntu Fanatic "If you're not living on the edge, you're taking up too much space."

  Read the article

• Download - Upload is too slow on Centos

  - by Mehdi

  My download/upload in server and out of server is too slow (around 50 KB/s !) ! Did I miss some configuration ? Some information: CentOS release 6.3 uptime load average: 0.17, 0.32, 0.37 Memory free -m total used free shared buffers cached Mem: 24009 21988 2021 0 806 18098 -/+ buffers/cache: 3083 20926 Swap: 4095 28 4067 lshw -C network *-network description: Ethernet interface product: 82574L Gigabit Network Connection vendor: Intel Corporation physical id: 0 bus info: pci@0000:02:00.0 logical name: eth0 version: 00 serial: 00:25:90:70:17:4a size: 100MB/s capacity: 1GB/s width: 32 bits clock: 33MHz capabilities: pm msi pciexpress msix bus_master cap_list ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt-fd autonegotiation configuration: autonegotiation=off broadcast=yes driver=e1000e driverversion=1.9.5-k duplex=full firmware=2.1-2 ip=108.175.8.123 latency=0 link=yes multicast=yes port=twisted pair speed=100MB/s resources: irq:16 memory:fb900000-fb91ffff ioport:e000(size=32) memory:fb920000-fb923fff ethtool ethtool eth0 Settings for eth0: Supported ports: [ TP ] Supported link modes: 10baseT/Half 10baseT/Full 100baseT/Half 100baseT/Full 1000baseT/Full Supports auto-negotiation: Yes Advertised link modes: Not reported Advertised pause frame use: No Advertised auto-negotiation: No Speed: 100Mb/s Duplex: Full Port: Twisted Pair PHYAD: 1 Transceiver: internal Auto-negotiation: off MDI-X: off Supports Wake-on: pumbg Wake-on: g Current message level: 0x00000001 (1) Link detected: yes dmesg |grep e1000e dmesg |grep e1000e e1000e: Intel(R) PRO/1000 Network Driver - 1.9.5-k e1000e: Copyright(c) 1999 - 2012 Intel Corporation. e1000e 0000:02:00.0: Disabling ASPM L0s e1000e 0000:02:00.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 e1000e 0000:02:00.0: setting latency timer to 64 e1000e 0000:02:00.0: irq 33 for MSI/MSI-X e1000e 0000:02:00.0: irq 34 for MSI/MSI-X e1000e 0000:02:00.0: irq 35 for MSI/MSI-X e1000e 0000:02:00.0: eth0: (PCI Express:2.5GT/s:Width x1) 00:25:90:70:17:4a e1000e 0000:02:00.0: eth0: Intel(R) PRO/1000 Network Connection e1000e 0000:02:00.0: eth0: MAC: 3, PHY: 8, PBA No: FFFFFF-0FF e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e 0000:02:00.0: eth0: Unsupported Speed/Duplex configuration e1000e: eth0 NIC Link is Up 10 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e 0000:02:00.0: Disabling ASPM L1 e1000e 0000:02:00.0: eth0: changing MTU from 1500 to 9000 e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None e1000e 0000:02:00.0: eth0: 10/100 speed: disabling TSO

  Read the article

• Configuring Wireless on Cisco 851W

  - by Aequitarum Custos

  Either a powersurge or something caused our router's configuration to get wiped, and our last backup was before the wireless network was setup. We have not been able to reconfigure the wireless since then, so was curious if anyone here would be able to determine what configuration is needed. We are using a Cisco 851W running 12.4(15)T9 We would like to use WPA encryption, and have it on the same network as the rest of the office network. Config file is below: User Access Verification Building configuration... Current configuration : 3857 bytes ! version 12.4 no service pad service timestamps debug datetime msec service timestamps log datetime msec service password-encryption no service dhcp ! hostname BOB ! boot-start-marker boot-end-marker ! enable secret 5 ********************* ! no aaa new-model ! ! dot11 syslog no ip source-route ! ! ip cef no ip bootp server ip domain name BOB.com ip name-server 61.11.1.1 ip name-server 61.11.1.2 ! ! ! username BOBB privilege 15 password 7 ************************* ! ! archive log config hidekeys ! ! ip tcp synwait-time 10 ! ! ! interface FastEthernet0 no cdp enable ! interface FastEthernet1 no cdp enable ! interface FastEthernet2 no cdp enable ! interface FastEthernet3 no cdp enable ! interface FastEthernet4 description WAN Connection$ETH-WAN$ ip address 61.11.1.14 255.255.254.0 ip nat outside ip virtual-reassembly duplex auto speed auto no cdp enable ! interface Dot11Radio0 no ip address shutdown ! encryption mode ciphers tkip speed basic-1.0 basic-2.0 basic-5.5 6.0 9.0 basic-11.0 12.0 18.0 24.0 36.0 48.0 54.0 station-role root no cdp enable ! interface Dot11Radio0.1 encapsulation dot1Q 1 native no cdp enable bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 spanning-disabled bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding ! interface Dot11Radio0.20 ip access-group Guest-ACL in no cdp enable ! interface Vlan1 description Internal Network ip address 192.168.2.60 255.255.255.0 ip nat inside ip nat enable ip virtual-reassembly ! ip forward-protocol nd ip route 0.0.0.0 0.0.0.0 61.11.2.14 ! ip http server no ip http secure-server ip nat inside source list 1 interface FastEthernet4 overload ! ip access-list extended Guest-ACL deny ip any 192.0.0.0 0.0.0.255 permit ip any any ! access-list 1 permit 192.0.0.0 0.0.0.255 access-list 100 remark SDM_ACL Category=2 access-list 100 permit ip 192.0.0.0 0.0.0.255 any no cdp run ! control-plane ! !

  Read the article

• How to set up a centralized backup server with lots of offsite workstations, intermittent internet connectivity, and stubborn users?

  - by Zac B

  This might be an impossible question. Context: We have a bunch of computers across around 1000 users. We have a centralized office where 900 of the users work, most of the time. Most of the computers are laptops. They are very frequently coming on and off the network for hours at a time. Users often take their computers home and do lots of work from home. In addition, there are a handful of users who work elsewhere in the country, who are offline (no internet connection whatsoever) for more than half of the time they use their machines. All of the machines are Windows 7/XP. Problem: People are always losing data. One day someone accidentally deletes a bunch of files. The next day someone else installs a bad driver or tries to mess with something in system32 and needs a personal data backup/reinstall of Windows. Because of how many of our business operations are done without an internet connection, and how frequently computers come on- and offline, it's unfeasible to make users use network storage for all of their data. We tried giving them Dropboxes, and they stored their files elsewhere. We bought and deployed Altiris, and they uninstalled it and blamed us when they couldn't get files back that they accidentally deleted while they were offline and hadn't taken a backup in months. We tried teaching them backup best-practices, and using scheduled sync tools to upload things to the network drives, and they turned them off because they "looked like viruses". It doesn't help that many of these users are pretty high up in the business and are not amicable to any sort of "you need to do something regularly because we say so" solution. Question: Other than finding another job where IT is treated differently and users are willing to follow best practices, how would people recommend I implement a file backup solution that supports the following: Backs up to a centralized server over LAN or WAN whenever a network link becomes available, or on a schedule. Supports interrupted/resumed backups (and hopefully file-delta only backups), since connections to the network (WAN or LAN) are often slow and only open for half an hour or so. Supports relatively rapid, "I accidentally deleted the TPS reports! Oh no!" single-file recovery, ideally administered from the central backup server rather than the client PC. Supports local-to-local file delta backup on a schedule, so that users without a network connection for a few days can still retrieve accidental deletions or whatnot. Ideally, the local stored backups would be pushed up to the server whenever network link is available. Isn't configurable on the clients without certain credentials. Because the CFOs (who won't give up their admin rights on the domain) will disable it if they can. Backs up the entire hard drive. There are people who are self-righteous about storing things in C:\, or in the recycle bin, or in the C:\Windows dir (yes, I know). I'm fine integrating multiple products/solutions, or scripting different programs together myself (I'm a somewhat competent programmer), but I've been drawing a blank on where to start. Dropbox is folder-specific, Altiris doesn't cope with LAN outages or interrupted/resumed backups, Volume Shadow Copy is awesome for a local-to-local solution, but I don't know how to push days of stored shadow copies up to a server in a 2 hour window of network access. The company is fine with spending decent money on this, thousands (USD) on a server, and hundreds on clients, if necessary. I want to emphasize that this isn't a shopping list request. While I wish there was a program out there that did what I want, I've looked pretty hard, and not found anything that fits the bill. Instead, I'm hoping for ideas on where to start hacking things together from scratch/from different technologies to make something stable that works. Cheers!

  Read the article

• Vagrant reporting VirtualBox guest additions out of date

  - by DTest

  Fairly new to Vagrant, so bear with me if I don't understand the process. I downloaded a CentOS box off http://www.vagrantbox.es/ Started it up running VirtualBox 4.2.4 and got this message: [default] The guest additions on this VM do not match the install version of VirtualBox! This may cause things such as forwarded ports, shared folders, and more to not work properly. If any of those things fail on this machine, please update the guest additions and repackage the box. Guest Additions Version: 4.0.8 VirtualBox Version: 4.2.4 So I used the vbguest plugin to update the guest additions, then repackaged the box as suggested. Having replaced the old box and loading it up I get the same message about guest additions being outdated, but vbguest reports that they are up to date (the automatic vbguest update is disabled in my Vagrantfile): Vagrant::Config.run do |config| config.vm.box = "centos56_64" config.vbguest.auto_update = false config.vbguest.no_remote = true end And the commands: dtest$ vagrant up [default] Importing base box 'centos56_64'... [default] The guest additions on this VM do not match the install version of VirtualBox! This may cause things such as forwarded ports, shared folders, and more to not work properly. If any of those things fail on this machine, please update the guest additions and repackage the box. Guest Additions Version: 4.0.8 VirtualBox Version: 4.2.4 [default] Matching MAC address for NAT networking... [default] Clearing any previously set forwarded ports... [default] Forwarding ports... [default] -- 22 => 2222 (adapter 1) [default] Creating shared folders metadata... [default] Clearing any previously set network interfaces... [default] Booting VM... [default] Waiting for VM to boot. This can take a few minutes. [default] VM booted and ready for use! [default] Mounting shared folders... [default] -- v-root: /vagrant dtest$ vagrant vbguest --no-install [default] Detected Virtualbox Guest Additions 4.2.4 --- OK. [default] Virtualbox Guest Additions on host: 4.2.4 - guest's version is 4.2.4 Since they appear to be updated after an install, I could ignore the message. But is it possible to get rid of it?

  Read the article

• iCloud stuff stops working while connected to OpenVPN [closed]

  - by Taco Bob

  I have a fairly simple OpenVPN setup on an OpenVZ VPS with Ubuntu 11.10. Client is the Viscosity client on Mac OS X 10.8.2, and after some testing, we can rule out the client as being part of the problem. Everything has been working fine except for Apple's iCloud stuff. Web surfing, email, FTP, NNTP, and Skype are all working as expected. It's ONLY the iCloud services that cease to function. If I connect to the VPN, iCloud stuff stops working. I no longer get anything in Messages, Calendar items don't get updated, and Notifications stop working. If I disconnect, the iCloud stuff all starts working. Connect again, iCloud stops working. Here's the server.conf: status openvpn-status.log log /var/log/openvpn.log verb 4 port 1194 proto udp dev tun ca /etc/openvpn/ca.crt cert /etc/openvpn/server.crt key /etc/openvpn/server.key dh /etc/openvpn/dh1024.pem server 10.9.8.0 255.255.255.0 ifconfig-pool-persist ipp.txt push "redirect-gateway def1" push “dhcp-option DNS 10.9.8.1? keepalive 10 120 duplicate-cn cipher BF-CBC comp-lzo user nobody group nogroup persist-key persist-tun tun-mtu 1500 mssfix 1400 I'm using iptables in a script, and it's also fairly simplistic. iptables -F iptables -t nat -F iptables -t mangle -F iptables -A FORWARD -i tun0 -o venet0 -j ACCEPT iptables -A FORWARD -i venet0 -o tun0 -j ACCEPT iptables -A INPUT -p tcp --dport 22 -j ACCEPT iptables -A INPUT -p tcp --dport 1194 -j ACCEPT iptables -A INPUT -p udp --dport 1194 -j ACCEPT iptables -t nat -A POSTROUTING -s 10.9.8.0/24 -j SNAT --to-source <server's public ip> echo 1 > /proc/sys/net/ipv4/ip_forward I tried forwarding ports as well, with no success. iptables -A FORWARD -p tcp -d 10.9.8.0/24 --dport 5222:5230 -j ACCEPT iptables -t nat -A PREROUTING -p tcp --dport 5222:5230 -j DNAT --to-destination 10.9.8.6 I am also sometimes behind a double-NAT situation that I have no control over. Client -> work VPN -> my OpenVPN box -> Internet. Client -> Airport Express -> ISP (which is doing NAT) -> my OpenVPN box -> Internet. Those two situations are just the fact of life where I am, and I cannot change them. I do have full control over my client and the OpenVPN server. I am completely out of ideas. I have posted a similar query at the OpenVPN forums, but it hasn't posted yet and seems to be in their moderation queue still. Tried on freenode irc channels, but nobody is awake, so here I am. I have Googled extensively for this, and can find nothing that is related. Help me get iCloud stuff working again!

  Read the article

• Log - Server kernel: INFO: task httpd:000000 blocked for more than 120 seconds

  - by valter

  Almost everyday my server is crashing due to hight server load, and even restarting apache or mysql can't solve the problem. I need to reboot the server to solve, or it crash again due to the high load. The log system records something like this when it crashes: Aug 11 18:33:53 server kernel: INFO: task httpd:20008 blocked for more than 120 seconds. Aug 11 18:33:53 server kernel: "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. Aug 11 18:33:53 server kernel: httpd D ffffffff801538ac 0 20008 5816 20066 19809 (NOTLB) Aug 11 18:33:53 server kernel: ffff81025a299dc8 0000000000000082 ffff81033b4c0740 ffffffff80009a14 Aug 11 18:33:53 server kernel: ffff8101063f8d80 0000000000000009 ffff8100b758f7e0 ffff8101c57187e0 Aug 11 18:33:53 server kernel: 00009436d4100b6c 000000000001d50f ffff8100b758f9c8 000000083b531588 Aug 11 18:33:53 server kernel: Call Trace: Aug 11 18:33:53 server kernel: [<ffffffff80009a14>] __link_path_walk+0x173/0xfb9 Aug 11 18:33:53 server kernel: [<ffffffff8002cc16>] mntput_no_expire+0x19/0x89 Aug 11 18:33:53 server kernel: [<ffffffff80063c4f>] __mutex_lock_slowpath+0x60/0x9b Aug 11 18:33:53 server kernel: [<ffffffff80023908>] __path_lookup_intent_open+0x56/0x97 Aug 11 18:33:53 server kernel: [<ffffffff80063c99>] .text.lock.mutex+0xf/0x14 Aug 11 18:33:53 server kernel: [<ffffffff8001b21f>] open_namei+0xea/0x712 Aug 11 18:33:54 server kernel: [<ffffffff8002768a>] do_filp_open+0x1c/0x38 Aug 11 18:33:54 server kernel: Firewall: *UDP_IN Blocked* IN=eth1 OUT= MAC=ff:ff:ff:ff:ff:ff:00:30:48:9e:6e:99:08:00 SRC=208.43.135.158 DST=255.255.255.255 LEN=151 TOS=0x00 PREC=0x00 TTL=64 ID=0 DF PROTO=UDP SPT=38354 DPT=6112 LEN=131 Aug 11 18:33:54 server kernel: [<ffffffff8001a061>] do_sys_open+0x44/0xbe Aug 11 18:33:54 server kernel: [<ffffffff8005d28d>] tracesys+0xd5/0xe0 I googled a lot trying to find a solution. But it looks that the solution is just to update the kernel or disk driver, thinks that I don't know how to do. In this url http://bugs.centos.org/view.php?id=4515 a lot o people report similar problems, except the fact that they are not related to httpd like mine. According to one member, one solution would be to add "elevator=noop " to /etc/grub.conf like in this example: title CentOS (2.6.18-238.12.1.el5xen) root (hd0,0) kernel /vmlinuz-2.6.18-238.12.1.el5xen ro root=/dev/VolGroup00/LogVol00 elevator=noop initrd /initrd-2.6.18-238.12.1.el5xen.img Would this really solve the problem? My disk are working in RAID. Can this cause some problem to my server? Is there any other solution?

  Read the article

• Resizing Partitions on Live RHEL/cPanel Server

  - by Timothy R. Butler

  I've resized many partitions over the years on Linux, Windows and Mac OS X -- but always using a GUI. However, the time has come where the preset partition sizes my data center placed on my server aren't the right sizes and I need to resize a production server's disks. I could fiddle with it and probably do OK, but given that it is a production server, I wanted to get some advice about the right way to do this. I do have KVM over IP access, so if it is best to take the server offline and boot off a rescue partition, I can do that. root [/var/lib/mysql]# df -h Filesystem Size Used Avail Use% Mounted on /dev/sda2 9.9G 2.1G 7.3G 23% / tmpfs 7.8G 0 7.8G 0% /dev/shm /dev/sda1 99M 77M 18M 82% /boot /dev/sda8 884G 463G 376G 56% /home /dev/sda3 9.9G 8.0G 1.5G 85% /usr /dev/sda5 9.9G 9.1G 308M 97% /var /usr/tmpDSK 2.0G 38M 1.8G 3% /tmp As you can see /var and /usr are quite close to being full and I've actually had to symlink some logs on /usr to directories in /home to balance things out. What I would like to do is to add 6-10 GB each to /usr and /var, presumably taking the space from /home. As I think about how the disk is arranged, the best thought I've come up with is to reduce /home by 16 GB, say, and move /var to the spot freed up, then allocating /var's space to /usr. However, that would put /var at the far end of the disk, which seems less than idea, given that MySQL has all of its data on that partition. I'd love to take the space out of the closer end of /usr, but I assume that would take a very arduous (and perhaps risky) process of moving all of the data in /usr around. I seem to recall having such a process fail for me on a computer in the past. The other option might be to merge / and /usr since / is underutilized, though I'm not sure if that's a good idea. Do you have any suggestions both on the best reallocation plan and the commands to use to accomplish it? UPDATE: I should add -- here's the partition table. There's one unused partition, which, if memory serves, was the original tmp location before I created a tmp image: Name Flags Part Type FS Type [Label] Size (MB) ------------------------------------------------------------------------------ Unusable 1.05* sda1 Boot Primary Linux ext2 106.96* sda2 Primary Linux ext3 10737.42* sda3 Primary Linux ext3 10737.42* sda5 NC Logical Linux ext3 10738.47* sda6 NC Logical Linux swap / Solaris 2148.54* sda7 NC Logical Linux ext3 1074.80* sda8 NC Logical Linux ext3 964098.53*

  Read the article

• Local DNS server (bind) and the router DHCP

  - by Luca

  I just set up an internal http server for internal use (I set up Redmine), in a small network (30 or so PCs). I set up the http server on a virtual box ubuntu, that runs also the DNS server (bind). In the DNS lookup I added the Redmine server name (redmine.engserver <- 192.168.1.14) and as forwarders the outside ISP DNS IP adresses. I am using a small wi-fi router (ASUS RT-N66U) as DHCP (and as gateway). In the DHCP config page I set up as DNS the ubuntu server IP (it is fixed 192.168.1.14). Now when I connect a new PC to the network, the DHCP router issues its new IP and as DNS servers it issues: primary: 192.168.1.14 (ubuntu machine) and seconary 192.168.1.1 (the router itself). ipconfig /all Default Gateway . . . . . . . . . : 192.168.1.1 DHCP Server . . . . . . . . . . . : 192.168.1.1 DHCPv6 IAID . . . . . . . . . . . : 248539109 DHCPv6 Client DUID. . . . . . . . : 00-01-00-01-17-15-AA-3F-D0-67-E5-49-A7-EF DNS Servers . . . . . . . . . . . : 192.168.1.14 192.168.1.1 NetBIOS over Tcpip. . . . . . . . : Enabled Before changing the DHCP setting on the router, I would always get only one DNS server: 192.168.1.1 (which uses probably DNS forwarding to external public DNS services). The problem is this: If in my browser I type www.google.com, it works all the time. If in the browser I type http://redmine.engserver/ it works most of the time, but sometimes it ends up with a yahoo page search or something else. In the DNS cache it shows as (Server not found). ipconfig /displaydns I looked with wireshark and it seems like sometimes the client PC interrogates the secondary DNS (192.168.1.1) instead of the first 192.168.1.14. Obviously this one is a public domain and it does not have the redmine.engserver entry. What is wrong in this configuration? Is it even legitimate to have 2 DNS (one internal and one forwarded by the router) which are inconsistent? Is there another way to have a local name service in a small office network? Why is the router DHCP issuing itself as DNS?

  Read the article

• 403 Forbidden Error when trying to view localhost on Apache

  - by misbehavens

  I think my Apache must be all screwed up. I don't know if it ever worked. I just upgraded to Snow Leopard, and the first step on this tutorial is to start apache and check that it's working by opening http://localhost. It starts fine but when I go to localhost I get a 403 forbidden error. I don't know where to start figuring out how to fix it, so I wonder if a fresh install of Apache would do the trick. What do you think? Update: I found some error logs in /private/var/log/apache2/. Found this in one of the logs. Not sure what it means: [Tue Nov 10 17:53:08 2009] [notice] caught SIGTERM, shutting down [Tue Nov 10 21:49:17 2009] [warn] Init: Session Cache is not configured [hint: SSLSessionCache] Warning: DocumentRoot [/usr/docs/dummy-host.example.com] does not exist Warning: DocumentRoot [/usr/docs/dummy-host2.example.com] does not exist httpd: Could not reliably determine the server's fully qualified domain name, using Andrews-Mac-Pro.local for ServerName mod_bonjour: Skipping user 'andrew' - cannot read index file '/Users/andrew/Sites/index.html'. [Tue Nov 10 21:49:19 2009] [notice] Digest: generating secret for digest authentication ... [Tue Nov 10 21:49:19 2009] [notice] Digest: done [Tue Nov 10 21:49:19 2009] [notice] Apache/2.2.11 (Unix) mod_ssl/2.2.11 OpenSSL/0.9.8k DAV/2 PHP/5.3.0 configured -- resuming normal operations Update: I also found something in the dummy-host.example.com-error_log file. I didn't set these dummy-host things by the way. Is this the default configuration? [Tue Nov 10 21:59:57 2009] [error] [client ::1] client denied by server configuration: /usr/docs Update: Woohoo! I found the file that had the virtual host definitions. It was in /etc/apache2/extra/httpd-vhosts.conf. It had those two dummy virtual host settings in there. I added a localhost virtual host. Not sure if this is necessary, but since it wasn't working before, decided to do it anyway. After removing the old virtual hosts, adding my new localhost virtual host, and restarting apache, it seems to work. So I guess whenever I want to add a virtual host, I only need to add them to this file? Or is there a hosts file somewhere, like there is on Linux? Update: Yes, there is an /etc/hosts file that need to be changed to. Add the virtual host name to that file.

  Read the article

• Why are the analoge stereo input and output of my M-Audio 24/96 soundcard not available to me in Ubuntu Lucid

  - by MIDoubleKO

  I have installed Lucid on an old Mac PowerPC G4 desktop with a M-Audio Audiophile 24/96 soundcard. The only inputs and outputs I can select in the audio preferences are digital ones for the digital input and output. "lspci -v" shows the card as so: 0001:10:13.0 Multimedia audio controller: VIA Technologies Inc. ICE1712 [Envy24] PCI Multi-Channel I/O Controller (rev 02) Subsystem: VIA Technologies Inc. Device d634 Flags: bus master, medium devsel, latency 16, IRQ 53 I/O ports at 0440 [size=32] I/O ports at 04b0 [size=16] I/O ports at 04a0 [size=16] I/O ports at 0400 [size=64] Capabilities: <access denied> Kernel driver in use: ICE1712 Kernel modules: snd-ice1712 "cat /proc/asound/cards" as so: 0 [Tumbler ]: PMac Tumbler - PowerMac Tumbler PowerMac Tumbler (Dev 21) Sub-frame 0 1 [M2496 ]: ICE1712 - M Audio Audiophile 24/96 M Audio Audiophile 24/96 at 0x440, irq 53 "aplay -L" shows these as listed: pulse Playback/recording through the PulseAudio sound server front:CARD=Tumbler,DEV=0 PowerMac Tumbler, PowerMac Tumbler Front speakers front:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi Front speakers surround40:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 4.0 Surround output to Front and Rear speakers surround41:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 4.1 Surround output to Front, Rear and Subwoofer speakers surround50:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 5.0 Surround output to Front, Center and Rear speakers surround51:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi 5.1 Surround output to Front, Center, Rear and Subwoofer speakers iec958:CARD=M2496,DEV=0 M Audio Audiophile 24/96, ICE1712 multi IEC958 (S/PDIF) Digital Audio Output I believe it is a problem with detecting the analogue input/output. Sometimes I can get sound from the device but it is a sheet of white noise and tinkering makes it go away again I don't know if that is a separate problem or if it is linked to not being able to see the analogue input/outputs in the sound preferences. Any help would be greatly appreciated As for the white noise I have installed the Envy24 control panel and spend lots of time playing with the settings but when I can get the white noise I can never get it to an quality where I can actually hear what is being played. The internal speaker plays audio fine and plugging in a NI Audio 4DJ via usb also plays sound, although with some static but I believe that is due to an underpowered usb2 pci expansion card not being able to get enough electricity to the device. Alternatively I have seen other people with problems with this device so it may be a bug in the driver but that is another matter. I would like to get the M-Audio card working so I can begin to enjoy my music once again. As a note, I do not currently have any audio equipment capable of sending or receiving audio via the digital inputs and output so I can not check if they are working. The sound preferences show a wide range of digital in and out options with various surround sound options but no analogue ins and outs.

  Read the article

• Email server can send internal, but messages never arrive at external recipients

  - by Chase Florell

  I'm running MailEnable on my server, and have been for many years. Recently we had an attack on our server, and I was able to close the hole. Since then, our mail server doesn't seem to be sending mail out. If I send an email from myself to another account hosted on the server, the email arrives as expected. If I send an email from my gmail account to my business account, the email also arrives as expected The problem comes when I send from my business account to an external domain I tried the following Gmail.com Hotmail.com Shaw.ca When I send to any of the above The message leaves my client as expected, The logs appear to accept and forward on the message The SMTP outbound que is empty The message never arrives I have checked our domain with mxtoolbox.com senderbase.org And neither of them are reporting any problems with our domain. I have ensured that port 25 is open (along with the other standard ports) Here is one of the log entries from the SMTP connector 11/05/13 12:10:00 SMTP-IN 494C0AF55CD0400FB90FD5E6525BC885.MAI 1312 127.0.0.1 220 mx1.example.com ESMTP MailEnable Service, Version: 6.81--6.81 ready at 11/05/13 12:10:00 0 0 11/05/13 12:10:00 SMTP-IN 494C0AF55CD0400FB90FD5E6525BC885.MAI 1312 127.0.0.1 EHLO EHLO ASSP.nospam 250-mx1.example.com [127.0.0.1], this server offers 6 extensions 159 18 11/05/13 12:10:00 SMTP-IN 494C0AF55CD0400FB90FD5E6525BC885.MAI 1312 127.0.0.1 EHLO EHLO ASSP.nospam 250-mx1.example.com [127.0.0.1], this server offers 6 extensions 159 18 11/05/13 12:10:01 SMTP-IN 494C0AF55CD0400FB90FD5E6525BC885.MAI 1312 127.0.0.1 AUTH AUTH LOGIN 334 VXNlcm5hbWU6 18 12 11/05/13 12:10:01 SMTP-IN 494C0AF55CD0400FB90FD5E6525BC885.MAI 1312 127.0.0.1 AUTH {blank} 334 UGFzc3dvcmQ6 18 26 [email protected] 11/05/13 12:10:01 SMTP-IN 494C0AF55CD0400FB90FD5E6525BC885.MAI 1312 127.0.0.1 AUTH Y29sb25lbGZhY2U= 235 Authenticated 19 18 [email protected] 11/05/13 12:10:01 SMTP-IN 494C0AF55CD0400FB90FD5E6525BC885.MAI 1312 127.0.0.1 MAIL MAIL FROM:<[email protected]> 250 Requested mail action okay, completed 43 31 [email protected] 11/05/13 12:10:01 SMTP-IN 494C0AF55CD0400FB90FD5E6525BC885.MAI 1312 127.0.0.1 RCPT RCPT TO:<[email protected]> 250 Requested mail action okay, completed 43 35 [email protected] 11/05/13 12:10:01 SMTP-IN 494C0AF55CD0400FB90FD5E6525BC885.MAI 1312 127.0.0.1 DATA DATA 354 Start mail input; end with <CRLF>.<CRLF> 46 6 [email protected] Here are the headers of the sent message X-Assp-Version: 1.7.5.7(1.0.07) on ASSP.nospam X-Assp-ID: ASSP.nospam 78601-04523 X-Assp-Intended-For: [email protected] X-Assp-Envelope-From: [email protected] Received: from [10.10.1.101] ([68.147.245.149] helo=[10.10.1.101]) with IPv4:587 by ASSP.nospam; 5 Nov 2013 12:10:00 -0700 From: Chase Florell <[email protected]> Content-Type: text/plain Content-Transfer-Encoding: 7bit Subject: Test Message Message-Id: <[email protected]> Date: Tue, 5 Nov 2013 12:10:18 -0700 To: Chase Florell <[email protected]> Mime-Version: 1.0 (Mac OS X Mail 7.0 \(1816\)) X-Mailer: Apple Mail (2.1816) . Where else can I check to see if there is something broken? What could cause a problem like this whereby the message appears to send, but never arrives, and never returns a bounce?

  Read the article

• Strange Upload Problem on Hyper-V

  - by Ring0

  Hi, This one is driving me totally nuts. I have being trying to upload a file to www.virustotal.com (its a harmless exe I have since found out - DiskWipe.exe from diskwipe.org). Using IE8. From Win 7 and Win 2008 R2 Datacenter (which I select to boot from vhd's) onto my main machine hardware, and also on another Win 7 PC elsewhere on my network, when I upload the file to virustotal.com it works perfectly. So, using my native NIC's everything is fine. Using another machine also perfect. Right. OK, from my boot menu the default is my main development machine - the one I'm typing on now. This runs on the metal and has Hyper-V role and I have some guests. All guests are not running. Amazingly, from my console (root partition to be exact) or any guest OS 2003 /XP / 2008 R2 etc. My upload to virustotal.com slows at 32% then HANGS at 38.something% & never finishes!! Here is the kicker. I have another box (my main server) running Hyper-V on the metal and three live guests. Identical H/W to my main dev machine in another room. (Except OS is Datacenter - Mine is Enterprise). If I try and upload from its bare metal console or any guest this file to virustotal.com using IE8 it stops exactly in the same place!! As for "steps I have tried etc." are kind-of blown out of the water as my server box is doing the precise same thing as the machine in my room here. OK, comonalities: Mobo: Gigabyte GA-X58-UD5, 12GB Kingston RAM, Corei7 920 4 cores hyperthreading = 8 & Realtek RTL8168D/8111D Family PCI-E Gigabit Ethernet NIC's. All 3 machines have this same motherboard - revision F11 Bios, all have 12GB RAM, all have the Realtek Nic's. All x64 by the way as I mentioned before I have a Win 7 box also with the UD5 m/Board, 12 GB RAM - bit of an overkill. :-) All these machines when NOT running Hyper-V can upload this file. Perhaps you may like to try it on a Hyepr-v (2008 R2) yourselves with IE8 and the desktop experience is on. See if it works or fails for you. Root OS or any guest. So, looking like its the NIC + Hyper-V = Cannot upload this file (any file I must add.) Realtek Nic is Ver 7.002.1125.2008. Using IE8 I see in the nic settings there are the usual parameters for Jumbo frames / Checksum offloading etc. several others. Should I fiddle with these? I ran Netmon 3.3 in a guest and the TCP session halted as the upload failed. I suppose I could study that further. I dont have Netmon on the root partition machine (yet)! All OS's fully patched - including todays defender files. My box running Office 2007 - but identical server in another room is not. Also, if I fire up a VPN to a distant client and do the upload it works! Of course its a different network path. Suggestions welcome please. If I left out anything important - please yell at me. Many Thanks,

  Read the article

< Previous Page | 543 544 545 546 547 548 549 550 551 552 553 554  | Next Page >