Search Results

Search found 24609 results on 985 pages for 'private ip'.

Page 549/985 | < Previous Page | 545 546 547 548 549 550 551 552 553 554 555 556  | Next Page >

• NIC light is turned off after boot on Redhat 4.6 server

  - by hoffmandirt

  I have a 2950 blade server setup with Red Hat 4.6 installed. I cannot get the NIC to work properly after reinstalling Linux. I activated the NIC, but the NIC light will not turn on when I plug the network cable into the hub. The status light on the hub will not turn on either. If I run ifconfig, the NIC status is UP. Also I can ping the IP address that I assign to the Linux machine, but I can't ping anything else that is plugged into the hub. When I reboot the system, the NIC light will stay on until the system fully boots and then it will turn off again. Is there something else that I need to do to get the NIC working? It appears to be disabled even though ifconfig says that it is UP. Maybe I need to configure something within the blade server (iDRAC)?

  Read the article

• help setting up an IPSEC vpn from my linux box

  - by robthewolf

  I have an office with a router and a remote server (Linux - Ubuntu 10.10). Both locations need to connect to a data supplier through a VPN. The VPN is an IPSEC gateway. I was able to configure my Linksys rv42 router to create a VPN connection successfully and now I need to do the same for Linux server. I have been messing around with this for too long. First I tried OpenVPN, but that is SSL and not IPSEC. Then I tried Shrew. I think I have the settings correct but I haven't been able to create the connection. It maybe that I have to use something else like a direct IPSEC config or something like that. If someone knows of a way to turn the following settings that I have been given below into a working IPSEC VPN connection I would be very grateful. Here are the settings I was given that must be used to connect to my supplier: Local destination network: 192.168.4.0/24 Local destination hosts: 192.168.4.100 Remote destination network: 192.167.40.0/24 Remote destination hosts: 192.168.40.27 VPN peering point: xxx.xxx.xxx.xxx Then they have given me the following details: IPSEC/ISAKMP Phase 1 Parameters: Authentication method: pre shared secret Diffie Hellman group: group 2 Encryption Algorithm: 3DES Lifetime in seconds:28800 Phase 2 parameters: IPSEC security: ESP Encryption algortims: 3DES Authentication algorithms: MD5 lifetime in seconds: 28800 pfs: disabled Here are the settings from my attempt to use shrew: n:version:2 n:network-ike-port:500 n:network-mtu-size:1380 n:client-addr-auto:0 n:network-frag-size:540 n:network-dpd-enable:1 n:network-notify-enable:1 n:client-banner-enable:1 n:client-dns-used:1 b:auth-mutual-psk:YjJzN2QzdDhyN2EyZDNpNG42ZzQ= n:phase1-dhgroup:2 n:phase1-keylen:0 n:phase1-life-secs:28800 n:phase1-life-kbytes:0 n:vendor-chkpt-enable:0 n:phase2-keylen:0 n:phase2-pfsgroup:-1 n:phase2-life-secs:28800 n:phase2-life-kbytes:0 n:policy-nailed:0 n:policy-list-auto:1 n:client-dns-auto:1 n:network-natt-port:4500 n:network-natt-rate:15 s:client-dns-addr:0.0.0.0 s:client-dns-suffix: s:network-host:xxx.xxx.xxx.xxx s:client-auto-mode:pull s:client-iface:virtual s:client-ip-addr:192.168.4.0 s:client-ip-mask:255.255.255.0 s:network-natt-mode:enable s:network-frag-mode:disable s:auth-method:mutual-psk s:ident-client-type:address s:ident-client-data:192.168.4.0 s:ident-server-type:address s:ident-server-data:192.168.40.0 s:phase1-exchange:aggressive s:phase1-cipher:3des s:phase1-hash:md5 s:phase2-transform:3des s:phase2-hmac:md5 s:ipcomp-transform:disabled Finally here is the debug output from the shrew log: 10/12/22 17:22:18 ii : ipc client process thread begin ... 10/12/22 17:22:18 < A : peer config add message 10/12/22 17:22:18 DB : peer added ( obj count = 1 ) 10/12/22 17:22:18 ii : local address 217.xxx.xxx.xxx selected for peer 10/12/22 17:22:18 DB : tunnel added ( obj count = 1 ) 10/12/22 17:22:18 < A : proposal config message 10/12/22 17:22:18 < A : proposal config message 10/12/22 17:22:18 < A : client config message 10/12/22 17:22:18 < A : local id '192.168.4.0' message 10/12/22 17:22:18 < A : remote id '192.168.40.0' message 10/12/22 17:22:18 < A : preshared key message 10/12/22 17:22:18 < A : peer tunnel enable message 10/12/22 17:22:18 DB : new phase1 ( ISAKMP initiator ) 10/12/22 17:22:18 DB : exchange type is aggressive 10/12/22 17:22:18 DB : 217.xxx.xxx.xxx:500 <- 206.xxx.xxx.xxx:500 10/12/22 17:22:18 DB : c1a8b31ac860995d:0000000000000000 10/12/22 17:22:18 DB : phase1 added ( obj count = 1 ) 10/12/22 17:22:18 : security association payload 10/12/22 17:22:18 : - proposal #1 payload 10/12/22 17:22:18 : -- transform #1 payload 10/12/22 17:22:18 : key exchange payload 10/12/22 17:22:18 : nonce payload 10/12/22 17:22:18 : identification payload 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v00 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v01 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v02 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( draft v03 ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports nat-t ( rfc ) 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local supports DPDv1 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is SHREW SOFT compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is NETSCREEN compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is SIDEWINDER compatible 10/12/22 17:22:18 : vendor id payload 10/12/22 17:22:18 ii : local is CISCO UNITY compatible 10/12/22 17:22:18 = : cookies c1a8b31ac860995d:0000000000000000 10/12/22 17:22:18 = : message 00000000 10/12/22 17:22:18 - : send IKE packet 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 ( 484 bytes ) 10/12/22 17:22:18 DB : phase1 resend event scheduled ( ref count = 2 ) 10/12/22 17:22:18 ii : opened tap device tap0 10/12/22 17:22:28 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:38 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:48 - : resend 1 phase1 packet(s) 217.xxx.xxx.xxx:500 - 206.xxx.xxx.xxx:500 10/12/22 17:22:58 ii : resend limit exceeded for phase1 exchange 10/12/22 17:22:58 ii : phase1 removal before expire time 10/12/22 17:22:58 DB : phase1 deleted ( obj count = 0 ) 10/12/22 17:22:58 ii : closed tap device tap0 10/12/22 17:22:58 DB : tunnel stats event canceled ( ref count = 1 ) 10/12/22 17:22:58 DB : removing tunnel config references 10/12/22 17:22:58 DB : removing tunnel phase2 references 10/12/22 17:22:58 DB : removing tunnel phase1 references 10/12/22 17:22:58 DB : tunnel deleted ( obj count = 0 ) 10/12/22 17:22:58 DB : removing all peer tunnel refrences 10/12/22 17:22:58 DB : peer deleted ( obj count = 0 ) 10/12/22 17:22:58 ii : ipc client process thread exit ...

  Read the article

• Configuration of Sonicwall Load Balancing

  - by jacke672

  We installed a Sonicwall NSA 240 appliance and have configured it up for our SSL VPN connection and for load balancing with 2 ADSL lines. Over the past week, I have been testing the load balancing options to optimize the connection speeds for our users - but I've run into the following: Round Robin load balancing is the ideal load balancing setting and it's roughly doubling our throughput- but, when it's active users are unable to access any SSL enabled websites such as banking, web-mail, etc. For this reason, I have been using percentage based balancing as it allows me to enable source and destination IP binding, which doesn't 'break' any secure connections but were left with the slow connection speeds we had before adding the second line. I'm looking for a method in which we can take advantage of the round robin connection speeds while allowing users to access sites with SSL certificates, all while still allowing our remote (vpn) users to connect. Any help would be appreciated. Thanks

  Read the article

• iptables -L lags on non localhost or anywhere address

  - by DazSlayer

  I am trying to configure iptables for ubuntu 10.04 and I have a problem with iptables -L lagging on rows where the destination or source address is not localhost or anywhere. The following entries will cause lag on their row: iptables -A INPUT -p tcp --dport 111 -s 192.168.1.14 -j ACCEPT iptables -A INPUT -p tcp --dport 90 -d 192.168.1.14 -j ACCEPT while this does not: iptables -A INPUT -p tcp --dport localhost -s 192.168.1.14 -j ACCEPT iptables -A INPUT -p tcp --dport localhost -d 192.168.1.14 -j ACCEPT I feel like this might be due to iptables checking to see if the ip is reachable. If not, what is the cause, if it is how can I disable it?

  Read the article

• Allow VMWare client to connect only via VPN

  - by Frank Meulenaar

  I have a VMWare (currently using Workstation on Vista, but thinking about switching to ESX) client with Windows XP. I've installed OpenVPN in the client and it connects to the corporate VPN server. I want to make sure that all traffic from the Windows XP machine goes trough this VPN tunnel, but I can't change any settings on the corporate VPN server. Is it possible to restrict the internet connectivity of the Windows XP client in such a way that it can only send packets to the IP of the corporate VPN server? In that way it'd be impossible for packets to bypass the tunnel. I've looked at NAT configurations but couldn't see how I could make this setup.

  Read the article

• pfsense CARP - wan failure on firewall

  - by eldblz

  I have recently configured 2 firewall (on 2 DELL PowerEdge R210II with ESXI 5.1) with pfsense. We have several LANs and 2 WANs. Everything is running fine but i have a strange behavior: i can access internet from alla LANs but not from the firewall (itself). For example the firewall cannot retrive package information or if i setup a gatway monitor ip (like google 8.8.8.8 ) this fails. These are the screenshots of firewall configuration: http://imgur.com/a/LNuMz#0 ATM i kept firewall rules to minimum to avoid problem or conflicts. Any ideas how to solve the problem? Thank you in advance.

  Read the article

• What do I do when I get a Linux kernel bug?

  - by raldi

  I just bought a tiny computer called a fit-pc2 which came with a somewhat customized Ubuntu 9.10 installation. uname -a reports: Linux 2.6.31-34-fitpc2 #7 SMP Thu Apr 22 17:43:26 IDT 2010 i686 GNU/Linux It seems that after several hours of running with heavy network load, all networking ceases and I get the following in kern.log: BUG: unable to handle kernel paging request at ff09dfc0 IP: [<c0150300>] kthread_should_stop+0x10/0x20 *pde = 00000000 Oops: 0000 [#1] SMP last sysfs file: /sys/devices/pci0000:00/0000:00:1d.7/usb1/idVendor Modules linked in: binfmt_misc ppdev sbc_fitpc2_wdt snd_usb_audio snd_usb_lib i2c_isch sch_gpio snd_seq_dummy snd_hda_intel snd_pcm_oss snd_seq_oss snd_seq_midi snd_rawmidi snd_mixer_oss snd_seq_midi_event snd_seq snd_pcm snd_timer snd_page_alloc snd_seq_device iptable_filter ip_tables x_tables snd_hwdep lpc_sch snd psmouse rt2860sta(C) uvcvideo video pl2303 soundcore mfd_core output videodev v4l1_compat lirc_igorplugusb lirc_dev serio_raw lp parport usbhid r8169 mii iegd_mod drm agpgart Pid: 16, comm: kblockd/1 Tainted: G C (2.6.31-34-fitpc2 #7) SBC-FITPC2 EIP: 0060:[<c0150300>] EFLAGS: 00010246 CPU: 1 EIP is at kthread_should_stop+0x10/0x20 EAX: ff09dfc4 EBX: c180cbac ECX: 0109d000 EDX: f709df98 ESI: f709df98 EDI: c180cba0 EBP: f709dfb8 ESP: f709df90 DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068 Process kblockd/1 (pid: 16, ti=f709c000 task=f7084b60 task.ti=f709c000) Stack: c014c14d c180cba4 00000000 f7084b60 c0150770 f709dfa4 f709dfa4 f7023ef4 <0> c180cba0 c014c0d0 f709dfe0 c015047c 00000000 00000000 00000000 f709dfcc <0> f709dfcc c0150400 00000000 00000000 00000000 c0103ce7 f7023ef4 00000000 Call Trace: [<c014c14d>] ? worker_thread+0x7d/0xe0 [<c0150770>] ? autoremove_wake_function+0x0/0x40 [<c014c0d0>] ? worker_thread+0x0/0xe0 [<c015047c>] ? kthread+0x7c/0x90 [<c0150400>] ? kthread+0x0/0x90 [<c0103ce7>] ? kernel_thread_helper+0x7/0x10 Code: a6 8b 55 0c 8d 4d e0 89 f8 89 34 24 e8 7a fd ff ff 89 c3 eb 92 90 90 90 90 90 90 55 64 a1 00 80 76 c0 8b 80 70 02 00 00 89 e5 5d <8b> 40 fc c3 8d b6 00 00 00 00 8d bf 00 00 00 00 55 ba d7 86 62 EIP: [<c0150300>] kthread_should_stop+0x10/0x20 SS:ESP 0068:f709df90 CR2: 00000000ff09dfc0 ---[ end trace 06004df70b9cf435 ]--- BUG: unable to handle kernel paging request at ff09dfc8 IP: [<c0521bc8>] _spin_lock_irqsave+0x18/0x30 *pde = 00000000 Oops: 0002 [#2] SMP last sysfs file: /sys/devices/pci0000:00/0000:00:1d.7/usb1/idVendor Modules linked in: binfmt_misc ppdev sbc_fitpc2_wdt snd_usb_audio snd_usb_lib i2c_isch sch_gpio snd_seq_dummy snd_hda_intel snd_pcm_oss snd_seq_oss snd_seq_midi snd_rawmidi snd_mixer_oss snd_seq_midi_event snd_seq snd_pcm snd_timer snd_page_alloc snd_seq_device iptable_filter ip_tables x_tables snd_hwdep lpc_sch snd psmouse rt2860sta(C) uvcvideo video pl2303 soundcore mfd_core output videodev v4l1_compat lirc_igorplugusb lirc_dev serio_raw lp parport usbhid r8169 mii iegd_mod drm agpgart Pid: 16, comm: kblockd/1 Tainted: G D C (2.6.31-34-fitpc2 #7) SBC-FITPC2 EIP: 0060:[<c0521bc8>] EFLAGS: 00010086 CPU: 1 EIP is at _spin_lock_irqsave+0x18/0x30 EAX: 00000100 EBX: ff09dfc8 ECX: 00000286 EDX: ff09dfc8 ESI: f7084b60 EDI: ff09dfc4 EBP: f709dd88 ESP: f709dd88 DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068 Process kblockd/1 (pid: 16, ti=f709c000 task=f7084b60 task.ti=f709c000) Stack: f709dda4 c0127c0b 00000082 00000001 ff09dfc4 f7084b60 00000000 f709ddd0 <0> c0137fd2 00000086 f70954c4 00000000 f7098480 f709ddf0 f7094fc0 f7084b60 <0> 00000000 00000009 f709ddf0 c013c3f8 00000001 c1807c60 f709ddf0 f7084b60 Call Trace: [<c0127c0b>] ? complete+0x1b/0x60 [<c0137fd2>] ? mm_release+0x52/0xf0 [<c013c3f8>] ? exit_mm+0x18/0x110 [<c013c6db>] ? do_exit+0xfb/0x2e0 [<c013998a>] ? print_oops_end_marker+0x2a/0x30 [<c0522aab>] ? oops_end+0x8b/0xd0 [<c011eac4>] ? no_context+0xb4/0xd0 [<c011eb1d>] ? __bad_area_nosemaphore+0x3d/0x1a0 [<c0133a56>] ? load_balance_newidle+0x96/0x320 [<c011ec92>] ? bad_area_nosemaphore+0x12/0x20 [<c0524106>] ? do_page_fault+0x2f6/0x380 [<c012cc30>] ? finish_task_switch+0x50/0xe0 [<c0523e10>] ? do_page_fault+0x0/0x380 [<c0522006>] ? error_code+0x66/0x70 [<c0523e10>] ? do_page_fault+0x0/0x380 [<c0150300>] ? kthread_should_stop+0x10/0x20 [<c014c14d>] ? worker_thread+0x7d/0xe0 [<c0150770>] ? autoremove_wake_function+0x0/0x40 [<c014c0d0>] ? worker_thread+0x0/0xe0 [<c015047c>] ? kthread+0x7c/0x90 [<c0150400>] ? kthread+0x0/0x90 [<c0103ce7>] ? kernel_thread_helper+0x7/0x10 Code: 00 00 00 55 89 e5 f0 83 28 01 79 05 e8 02 ff ff ff 5d c3 55 89 c2 89 e5 9c 58 8d 74 26 00 89 c1 fa 90 8d 74 26 00 b8 00 01 00 00 <f0> 66 0f c1 02 38 e0 74 06 f3 90 8a 02 eb f6 89 c8 5d c3 90 8d EIP: [<c0521bc8>] _spin_lock_irqsave+0x18/0x30 SS:ESP 0068:f709dd88 CR2: 00000000ff09dfc8 ---[ end trace 06004df70b9cf436 ]--- Fixing recursive fault but reboot is needed! This seems to happen at least once a day. How do I even begin to debug this?

  Read the article

• What do I do when I get a Linux kernel bug?

  - by raldi

  I just bought a tiny computer called a fit-pc2 which came with a somewhat customized Ubuntu 9.10 installation. uname -a reports: Linux 2.6.31-34-fitpc2 #7 SMP Thu Apr 22 17:43:26 IDT 2010 i686 GNU/Linux It seems that after several hours of running with heavy network load, all networking ceases and I get the following in kern.log: BUG: unable to handle kernel paging request at ff09dfc0 IP: [<c0150300>] kthread_should_stop+0x10/0x20 *pde = 00000000 Oops: 0000 [#1] SMP last sysfs file: /sys/devices/pci0000:00/0000:00:1d.7/usb1/idVendor Modules linked in: binfmt_misc ppdev sbc_fitpc2_wdt snd_usb_audio snd_usb_lib i2c_isch sch_gpio snd_seq_dummy snd_hda_intel snd_pcm_oss snd_seq_oss snd_seq_midi snd_rawmidi snd_mixer_oss snd_seq_midi_event snd_seq snd_pcm snd_timer snd_page_alloc snd_seq_device iptable_filter ip_tables x_tables snd_hwdep lpc_sch snd psmouse rt2860sta(C) uvcvideo video pl2303 soundcore mfd_core output videodev v4l1_compat lirc_igorplugusb lirc_dev serio_raw lp parport usbhid r8169 mii iegd_mod drm agpgart Pid: 16, comm: kblockd/1 Tainted: G C (2.6.31-34-fitpc2 #7) SBC-FITPC2 EIP: 0060:[<c0150300>] EFLAGS: 00010246 CPU: 1 EIP is at kthread_should_stop+0x10/0x20 EAX: ff09dfc4 EBX: c180cbac ECX: 0109d000 EDX: f709df98 ESI: f709df98 EDI: c180cba0 EBP: f709dfb8 ESP: f709df90 DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068 Process kblockd/1 (pid: 16, ti=f709c000 task=f7084b60 task.ti=f709c000) Stack: c014c14d c180cba4 00000000 f7084b60 c0150770 f709dfa4 f709dfa4 f7023ef4 <0> c180cba0 c014c0d0 f709dfe0 c015047c 00000000 00000000 00000000 f709dfcc <0> f709dfcc c0150400 00000000 00000000 00000000 c0103ce7 f7023ef4 00000000 Call Trace: [<c014c14d>] ? worker_thread+0x7d/0xe0 [<c0150770>] ? autoremove_wake_function+0x0/0x40 [<c014c0d0>] ? worker_thread+0x0/0xe0 [<c015047c>] ? kthread+0x7c/0x90 [<c0150400>] ? kthread+0x0/0x90 [<c0103ce7>] ? kernel_thread_helper+0x7/0x10 Code: a6 8b 55 0c 8d 4d e0 89 f8 89 34 24 e8 7a fd ff ff 89 c3 eb 92 90 90 90 90 90 90 55 64 a1 00 80 76 c0 8b 80 70 02 00 00 89 e5 5d <8b> 40 fc c3 8d b6 00 00 00 00 8d bf 00 00 00 00 55 ba d7 86 62 EIP: [<c0150300>] kthread_should_stop+0x10/0x20 SS:ESP 0068:f709df90 CR2: 00000000ff09dfc0 ---[ end trace 06004df70b9cf435 ]--- BUG: unable to handle kernel paging request at ff09dfc8 IP: [<c0521bc8>] _spin_lock_irqsave+0x18/0x30 *pde = 00000000 Oops: 0002 [#2] SMP last sysfs file: /sys/devices/pci0000:00/0000:00:1d.7/usb1/idVendor Modules linked in: binfmt_misc ppdev sbc_fitpc2_wdt snd_usb_audio snd_usb_lib i2c_isch sch_gpio snd_seq_dummy snd_hda_intel snd_pcm_oss snd_seq_oss snd_seq_midi snd_rawmidi snd_mixer_oss snd_seq_midi_event snd_seq snd_pcm snd_timer snd_page_alloc snd_seq_device iptable_filter ip_tables x_tables snd_hwdep lpc_sch snd psmouse rt2860sta(C) uvcvideo video pl2303 soundcore mfd_core output videodev v4l1_compat lirc_igorplugusb lirc_dev serio_raw lp parport usbhid r8169 mii iegd_mod drm agpgart Pid: 16, comm: kblockd/1 Tainted: G D C (2.6.31-34-fitpc2 #7) SBC-FITPC2 EIP: 0060:[<c0521bc8>] EFLAGS: 00010086 CPU: 1 EIP is at _spin_lock_irqsave+0x18/0x30 EAX: 00000100 EBX: ff09dfc8 ECX: 00000286 EDX: ff09dfc8 ESI: f7084b60 EDI: ff09dfc4 EBP: f709dd88 ESP: f709dd88 DS: 007b ES: 007b FS: 00d8 GS: 0000 SS: 0068 Process kblockd/1 (pid: 16, ti=f709c000 task=f7084b60 task.ti=f709c000) Stack: f709dda4 c0127c0b 00000082 00000001 ff09dfc4 f7084b60 00000000 f709ddd0 <0> c0137fd2 00000086 f70954c4 00000000 f7098480 f709ddf0 f7094fc0 f7084b60 <0> 00000000 00000009 f709ddf0 c013c3f8 00000001 c1807c60 f709ddf0 f7084b60 Call Trace: [<c0127c0b>] ? complete+0x1b/0x60 [<c0137fd2>] ? mm_release+0x52/0xf0 [<c013c3f8>] ? exit_mm+0x18/0x110 [<c013c6db>] ? do_exit+0xfb/0x2e0 [<c013998a>] ? print_oops_end_marker+0x2a/0x30 [<c0522aab>] ? oops_end+0x8b/0xd0 [<c011eac4>] ? no_context+0xb4/0xd0 [<c011eb1d>] ? __bad_area_nosemaphore+0x3d/0x1a0 [<c0133a56>] ? load_balance_newidle+0x96/0x320 [<c011ec92>] ? bad_area_nosemaphore+0x12/0x20 [<c0524106>] ? do_page_fault+0x2f6/0x380 [<c012cc30>] ? finish_task_switch+0x50/0xe0 [<c0523e10>] ? do_page_fault+0x0/0x380 [<c0522006>] ? error_code+0x66/0x70 [<c0523e10>] ? do_page_fault+0x0/0x380 [<c0150300>] ? kthread_should_stop+0x10/0x20 [<c014c14d>] ? worker_thread+0x7d/0xe0 [<c0150770>] ? autoremove_wake_function+0x0/0x40 [<c014c0d0>] ? worker_thread+0x0/0xe0 [<c015047c>] ? kthread+0x7c/0x90 [<c0150400>] ? kthread+0x0/0x90 [<c0103ce7>] ? kernel_thread_helper+0x7/0x10 Code: 00 00 00 55 89 e5 f0 83 28 01 79 05 e8 02 ff ff ff 5d c3 55 89 c2 89 e5 9c 58 8d 74 26 00 89 c1 fa 90 8d 74 26 00 b8 00 01 00 00 <f0> 66 0f c1 02 38 e0 74 06 f3 90 8a 02 eb f6 89 c8 5d c3 90 8d EIP: [<c0521bc8>] _spin_lock_irqsave+0x18/0x30 SS:ESP 0068:f709dd88 CR2: 00000000ff09dfc8 ---[ end trace 06004df70b9cf436 ]--- Fixing recursive fault but reboot is needed! This seems to happen at least once a day. How do I even begin to debug this?

  Read the article

• Redhat doesn't set my desired hostname on reboot

  - by tomdee

  I have a redhat (EL5) server that I need to change the hostname on. I'm trying to put it back into a known state to help with server provisioning activities. As part of changing the hostname, I'm updating /etc/sysconfig/network and /etc/hosts. I also have an explicit call to hostname. My desired state is that the server thinks its hostname is "localhost". And a call to "hostname" returns "localhost". The problem I'm having is that when I reboot, the hostname is reverted to "localhost.companyname.com" which is not what I want. How do I ensure that the hostname is set up as just "localhost" when I reboot? My /etc/sysconfig/network file contains: NETWORKING=yes HOSTNAME=localhost GATEWAY=123.123.123.123 #I do have a proper IP address here My /etc/hosts file contains: 127.0.0.1 localhost.localdomain localhost 172.21.1.1 localhost.companyname.com localhost

  Read the article

• Routing to various node.js servers on same machine

  - by Dtang

  I'd like to set up multiple node.js servers on the same machine (but listening on different ports) for different projects (so I can pull any down to edit code without affecting the others). However I want to be able to access these web apps from a browser without typing in the port number, and instead map different urls to different ports: e.g. 45.23.12.01/app - 45.23.12.01:8001. I've considered using node-http-proxy for this, but it doesn't yet support SSL. My hunch is that nginx might be the most suitable. I've never set up nginx before - what configuration do I need to do? The examples of config files I've seen only deal with subdomains, which I don't have. Alternatively, is there a better (stable, hassle-free) way of hosting multiple apps under the same IP address?

  Read the article

• DNS record question

  - by Just plain me

  So I have two Windows domains/seperate forests. One forest consist of what is left of the bought-out company's domain. They have 5 servers that still have important data and need to be worked with on a daily basis by a large group of employees. We have a forest level trust setup to ease file access. We manually create DNS A records for the 5 servers so their short names would resolve to the IP addresses. I need the FQDN to resolve though. Should I create CName records to achieve this? I hope this question makes sense, I am learning DNS on the fly... :)

  Read the article

• How to make a DHCP server on virtual machine serves other virtual machines(on different physical machines)?

  - by Tony

  I'm building a virtual cluster with VirtualBox and Opensuse. I have 10 physical machines and need several vms on each. The virtual machines are supposed to be in a "private" network, but still have internet access. I was asked to set up a virtual head node working as DHCP server. I installed DHCP server on the virtual head node and it seems works. On VirtualBox I set 2 network adapters to the head node, one bridged adapter and one internal network. One vm on the same physical machine has been set nic as internal network adapter. The vm can get IP address (so DHCP works) but can't access internet. What should I do? Specifically, what network adapter should I choose for head-node and work-nodes in VirtualBox? What in the virtual machines should I do?

  Read the article

• Survey for OS/Browsers etc for an external Agency.

  - by ggonsalv

  We need to design an browser application accessed by a fixed set of external entities (providers). I was wondering if there is a pre-existing survey that is 1) Online 2) Determines the browsers being used etc. without the users having to type it in 3) Determine connectivity from IP address. (Like how Speedtest.com does ). It can tell what your ISP is ,etc without having the user fill it in. The ability to add other questions. So basically a recipient of the survey would navigate to the site, the survey questions that can be inferred , are prefilled so as make recipient only answer the non-technical questions of the survey.

  Read the article

• Limit maximum incoming connections to a port using iptables

  - by Harley

  I have a server that has apache listening on a number of ports. Some ports are used for configuring the server, and another is used to download large files. My problem is that when I have a large number of clients downloading files, the web interface is uncontactable. I would like to limit the number of clients connecting on the "large file" port so that apache always has available connections to configure the server. A REJECT is fine, the client trying to download the file will back off and retry later. Each client only has one connection open to the server at a time, so limiting by IP won't work. I know I could put something in front of apache to manage this, but I'd really like to do it in iptables, without adding more software.

  Read the article

• How should I setup separate mx records for a subdomain?

  - by Chris Adams

  Lets say I have a domain that I run a web app on, for example cranketywidgets.com, and I'm using google apps for handle email for people work work on that domain, i.e. support@ cranketywidgets.com, [email protected], [email protected] and so on. Google's own mail services aren't always the best for sending automated reminder emails, comment notifications and so on, so the current solution I plan to pursue is to create a separate subdomain called mailer.cranketywidgets.com, run a mail server off it, and create a few accounts specifically for sending these kinds of emails. What should the mx records and a records look like here for this? I'm somewhat confused by the fact that mx records can be names, but that they must eventually resolve to an A record. What should the records look like here? cranketywidgets.com - A record to actual server like 10.24.233.214 cranketywidgets.com - mx records for google's email apps mailer.cranketywidgets.com - mx name pointing to server's ip address Would greatly appeciate some help on this - the answer seems like it'll be obvious, but email spam is a difficult problem to solve.

  Read the article

• AFXR problem using gradwell secondary DNS

  - by Roaders

  Hi All I use Gradwell.com to provide secondary DNS but I keep getting e-mails along the lines of the following saying that it's not working: You have asked us to provide a secondary DNS service for the following domain(s) Unfortunately, the primary DNS server(s) you specified are not permitting the necessary zone transfers from our servers, or they are not answering "SOA" queries for your domain correctly. I have gone through the support procedure and they weren't that helpful. They have suggested the following: Our secondline team have suggested setting the AXFR to use anouther machine. This will ensure that the transfer is not locked down to one machine and should allow any machine to make the request I don't really know what AFXR is and I only have 1 production machine so I can't set the AFXR to use another one! In previous support correspondence we confirmed that I am allowing transfers to the correct IP and that I have the correct ports open on the firewall. I am running Windows Server 2003. What can I do to try and get these zone transfers working? Thanks

  Read the article

• How do I access site.project.rails (running on host) from VMWare fusion?

  - by Johnny Mnemonic

  I have a rails app setup and running on my snow leopard MacBook - the app is being served by Passenger. As part of the setup they had me add entries for 127.0.0.1 site.project.rails in my hosts file so I could reach the site from site.project.rails I can't for the life of me figure out how to get the app show up in VMWare. I have XP setup and browse to http://site.project.rails and I can't get it to show up. I setup a basic rails app, being served at localhost:3000 by webrick, I can get that to load by visiting my hosts ip (http://192.168.1.1:3000/). I added the same hosts I added on my Mac to Windows. I also Bridged the network under settings for the VM. What am I missing?

  Read the article

• How to use ssl_verify_client=ON on one virtual server and ssl_verify_client=OFF on another?

  - by Alexander Artemenko

  I want to force ssl client verification for on of my virtual hosts. But get "No required SSL certificate was sent" error, trying to GET something from it. Here are my test configs: # defaults ssl_certificate /etc/certs/server.cer; ssl_certificate_key /etc/certs/privkey-server.pem; ssl_client_certificate /etc/certs/allcas.pem; server { listen 1443 ssl; server_name server1.example.com; root /tmp/root/server1; ssl_verify_client off; } server { listen 1443 ssl; server_name server2.example.com; root /tmp/root/server2; ssl_verify_client on; } First server replies with 200 http code, but second returns "400 Bad Request, No required SSL certificate was sent, nginx/1.0.4". Probably, it is implossible to use ssl_verify_client on the same IP? Should I bind these servers to different IPs, will it solve my problem?

  Read the article

• Redirect an Apache2 SSL VirtualHost with mod_alias

  - by Jeff

  I want to make sure there aren't any odd behaviors that I don't know about when redirecting a SSL VirtualHost with mod_alias Redirect as outlined by Apache here. My code seems to work, but since SSL virtual hosts are restricted to just one IP address, I want to make sure there aren't any problems eluding me. Explicitly not using TLS. I'm stuck with Apache 2.2 for now. <VirtualHost *:443> ServerName example.com SSLEngine On Redirect 301 / https://www.example.com/ </VirtualHost> <VirtualHost *:443> ServerName www.example.com SSLEngine On # Do stuff # </VirtualHost> So I guess my question is, should SSL VirtualHost redirection with mod_alias Redirect work the same as non-SSL redirection?

  Read the article

• Windows IIS test server setup

  - by chopps

  hello everyone, I picked up a new server to do some testing and need of a little help in setting up my environment at home. Here is what I would like to do: The test server will be used to test new code and configurations for a SaaS product. I would like from my laptop to enter www.acme.com and have it hit the server. The server is connected to a wireless router. I have windows server 2008 with IIS running on an an IP of 192.168.1.4. What is the best way to set this up? I want to hit the test server for www.acme.com and not go out to the internet. Do i need to mess with the LMHosts file? Thanks for the help. Im sure its easy but have never done this before.

  Read the article

• Win7 Prof. Computer won't wake on lan via Magic Packet from outside network

  - by Michael

  Hi all. I just purchased a new computer running Windows 7 Professional x64. I'd like to save power by having it sleep after an hour, but I would also like to be able to Remote Desktop into it at my leisure. I set up a static IP and have port forwarding set up on the router. If the computer is awake, the RDP connection works just fine. I downloaded and installed Wake-On-Lan thanks to this article If I put my new computer to sleep and send the magic packet from my old computer inside of my home network it wakes up. If I do the same thing, however, from my work computer outside the network it does not. I figured the Firewall was blocking the incoming traffic, but nothing in the Windows Firewall logs points to this happening. I'm wondering if anyone has any suggestions or any tests I can run through in order to narrow down what the problem might be. Thanks in advance for any help you might be able to offer.

  Read the article

• Set up linux box for hosting a-z

  - by microchasm

  I am in the process of reinstalling the OS on a machine that will be used to host a couple of apps for our business. The apps will be local only; access from external clients will be via vpn only. The prior setup used a hosting control panel (Plesk) for most of the admin, and I was looking at using another similar piece of software for the reinstall - but I figured I should finally learn how it all works. I can do most of the things the software would do for me, but am unclear on the symbiosis of it all. This is all an attempt to further distance myself from the land of Configuration Programmer/Programmer, if at all possible. I can't find a full walkthrough anywhere for what I'm looking for, so I thought I'd put up this question, and if people can help me on the way I will edit this with the answers, and document my progress/pitfalls. Hopefully someday this will help someone down the line. The details: CentOS 5.5 x86_64 httpd: Apache/2.2.3 mysql: 5.0.77 (to be upgraded) php: 5.1 (to be upgraded) The requirements: SECURITY!! Secure file transfer Secure client access (SSL Certs and CA) Secure data storage Virtualhosts/multiple subdomains Local email would be nice, but not critical The Steps: Download latest CentOS DVD-iso (torrent worked great for me). Install CentOS: While going through the install, I checked the Server Components option thinking I was going to be using another Plesk-like admin. In hindsight, considering I've decided to try to go my own way, this probably wasn't the best idea. Basic config: Setup users, networking/ip address etc. Yum update/upgrade. Upgrade PHP/MySQL: To upgrade PHP and MySQL to the latest versions, I had to look to another repo outside CentOS. IUS looks great and I'm happy I found it! Add IUS repository to our package manager cd /tmp wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/epel-release-1-1.ius.el5.noarch.rpm rpm -Uvh epel-release-1-1.ius.el5.noarch.rpm wget http://dl.iuscommunity.org/pub/ius/stable/Redhat/5/x86_64/ius-release-1-4.ius.el5.noarch.rpm rpm -Uvh ius-release-1-4.ius.el5.noarch.rpm yum list | grep -w \.ius\. # list all the packages in the IUS repository; use this to find PHP/MySQL version and libraries you want to install Remove old version of PHP and install newer version from IUS rpm -qa | grep php # to list all of the installed php packages we want to remove yum shell # open an interactive yum shell remove php-common php-mysql php-cli #remove installed PHP components install php53 php53-mysql php53-cli php53-common #add packages you want transaction solve #important!! checks for dependencies transaction run #important!! does the actual installation of packages. [control+d] #exit yum shell php -v PHP 5.3.2 (cli) (built: Apr 6 2010 18:13:45) Upgrade MySQL from IUS repository /etc/init.d/mysqld stop rpm -qa | grep mysql # to see installed mysql packages yum shell remove mysql mysql-server #remove installed MySQL components install mysql51 mysql51-server mysql51-devel transaction solve #important!! checks for dependencies transaction run #important!! does the actual installation of packages. [control+d] #exit yum shell service mysqld start mysql -v Server version: 5.1.42-ius Distributed by The IUS Community Project Upgrade instructions courtesy of IUS wiki: http://wiki.iuscommunity.org/Doc/ClientUsageGuide Install rssh (restricted shell) to provide scp and sftp access, without allowing ssh login cd /tmp wget http://dag.wieers.com/rpm/packages/rssh/rssh-2.3.2-1.2.el5.rf.x86_64.rpm rpm -ivh rssh-2.3.2-1.2.el5.rf.x86_64.rpm useradd -m -d /home/dev -s /usr/bin/rssh dev passwd dev Edit /etc/rssh.conf to grant access to SFTP to rssh users. vi /etc/rssh.conf Uncomment or add: allowscp allowsftp This allows me to connect to the machine via SFTP protocol in Transmit (my FTP program of choice; I'm sure it's similar with other FTP apps). rssh instructions appropriated (with appreciation!) from http://www.cyberciti.biz/tips/linux-unix-restrict-shell-access-with-rssh.html Set up virtual interfaces ifconfig eth1:1 192.168.1.3 up #start up the virtual interface cd /etc/sysconfig/network-scripts/ cp ifcfg-eth1 ifcfg-eth1:1 #copy default script and match name to our virtual interface vi ifcfg-eth1:1 #modify eth1:1 script #ifcfg-eth1:1 | modify so it looks like this: DEVICE=eth1:1 IPADDR=192.168.1.3 NETMASK=255.255.255.0 NETWORK=192.168.1.0 ONBOOT=yes NAME=eth1:1 Add more Virtual interfaces as needed by repeating. Because of the ONBOOT=yes line in the ifcfg-eth1:1 file, this interface will be brought up when the system boots, or the network starts/restarts. service network restart Shutting down interface eth0: [ OK ] Shutting down interface eth1: [ OK ] Shutting down loopback interface: [ OK ] Bringing up loopback interface: [ OK ] Bringing up interface eth0: [ OK ] Bringing up interface eth1: [ OK ] ping 192.168.1.3 64 bytes from 192.168.1.3: icmp_seq=1 ttl=64 time=0.105 ms And this is where I'm at. I will keep editing this as I make progress. Any tips on how to Configure virtual interfaces/ip based virtual hosts for SSL, setting up a CA, or anything else would be appreciated.

  Read the article

• Nginx. How do I reject request to unlisted ssl virtual server?

  - by Osw

  I have a wildcard SSL certificate and several subdomains on the same ip. Now I want my nginx to handle only mentioned server names and drop connection for others so that it'd look like nginx is not running for unlisted server names (not responding, rejecting, dead, not a single byte in response). I do the following ssl_certificate tls/domain.crt; ssl_certificate_key tls/domain.key; server { listen 1.2.3.4:443 ssl; server_name validname.domain.com; // } server { listen 1.2.3.4:443 ssl; server_name _; // deny all; // return 444; // return 404; //location { // deny all; //} } I've tried almost everything in the last server block, but no success. I get either valid response from known virtual server or error code. Please help.

  Read the article

• Cisco router for educational purposes

  - by user39214

  Hey all. I want to buy a Cisco router to use on my home network. I'm just hoping to get a unit that is not too old and is not a SOHO model. I want to run the latest Cisco OS just to learn how Cisco does things. I would use it to divide my network into two or three IP networks, firewalling, etc. I'm just asking for a model name/number. Thanks.

  Read the article

• Error while starting web application.

  - by Lalit

  0 When you right-click a Web site in the Microsoft Internet Information Services (IIS) Microsoft Management Console (MMC) snap-in, and then you click Start, the Web site does not start and you receive the following error message: The process cannot access the file because it is being used by another process. What have to do. To resolve this issue i got this solution form link http://support.microsoft.com/kb/890015 As: You must use the Netstat.exe utility at the command line to see if another process is using port 80 or port 443. But how to ensure that is these Ip are in use or not ? in terms of status ? What should its status ? Second solution is : HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\HTTP\Parameters\ListenOnlyList. But this key is not found .

  Read the article

< Previous Page | 545 546 547 548 549 550 551 552 553 554 555 556  | Next Page >