Search Results

Search found 6552 results on 263 pages for 'recovery models'.

Page 55/263 | < Previous Page | 51 52 53 54 55 56 57 58 59 60 61 62  | Next Page >

  • Ways to recover data from external hard drive

    - by Howard Benson
    I use an external hard disk for backup of my mac with time machine (OS 10.5.8). I have made something wrong and I have found important folders in the recycler bin. These folders come from external hd. They are backup folders (backups.backupdb) and others. I have tried to restore them draggin and dropping. Some of them came back in the external hd in a while. For the others it takes hours to "preparing to copy" and then it has said "there's no space to copy" on ext hd. It's strange. Files are now in the recycle bin (180gb), and the ext had should have lot of free space. But it isn't really so. Ext hd is not free of space even if these files are in the bin. I ask for advices. I'm not also able to use time machine now (and i have "lost" old backups) for the same reason. Ext hd says that it has not free space.. Thanks

    Read the article

  • Forgotten account password

    - by blade
    I kept my passwords recorded but the location on my PC where I kept this went missing. I now can't get into Windows Server 2008 R2 as I can't remember the administrator or named account credentials and have no password reset disk. This is on a VM (VM Player - which btw is temp till I get Hyper-V). How can I get back in? If I make AD can I join the server to AD and then set a domain account?

    Read the article

  • SEAGATE Barracuda 7200.11 HDD not running

    - by Dane411
    After a huge research, I'm stuck at the beggining of getting my HDD data back. Whats happening to me is that in the moment when I plug the power wire to my external 1TB SEAGATE Barracuda 7200.11 ST31000333AS HDD Fw LC15, it makes the sound like it's spinning to almost full speed and then shuts down and spins up again, and so on. It's well known that those HDDs have a bad firmware that someday randomly fails. There are like 2 main problems identified, BSY (busy) state, and LBA0 error. Last time I connected it to power nothing happened, it didnt try to start at all, is it that so called bricked state? I guess my HDDs error is the first one, but I dont really know if what I described is that BSY state or not, neither I know how to check it. How could I know it? Thank you so much!

    Read the article

  • Looking for suggestions for hosting Windows 2000 Server in the cloud / VPS / etc?

    - by JohnyD
    I have a Windows 2000 Server, currently virtualized in Hyper-V, that I would like to get running off-site as a backup (cloud, VPS, etc). You can't virtualize in EC2 and I'm fairly certain there are no Server 2000 AMI's floating about (correct me if I'm wrong!). If anyone has a recommendation on how I can get a virtualized Windows 2000 Server running in a secure, remote environment I would be grateful. As far as locations go I'd be interested in both North America as well as Australia and Europe. In a nutshell, we're ploughing our way out of a legacy codebase and this server is the last that remains of the legacy apps. However, it is still very much used by our clients. Everything is backed up each night (data, images, etc) to tape which is then taken offsite. However, in the event of a fire I would love to have a backup legacy server to point DNS records to. So while I am rebuilding from the ashes our services would already be available. It would save a lot of time and make my managers all the more happy (and that's what it's all about, riighhtt? :D) Thank you all for your suggestions. Please let me know if I've left out any important information. Additional info: - the legacy codebase does not function properly in Server 2003

    Read the article

  • Raid 5 and Power Supply damage?

    - by Tronic
    Hi. Because I build a RAID 5 atm, I wanted to ask, what would happen if the server with a raid 5 in it (like 4-5 hdds) would have a power supply damage? Can I just switch the power supply and my data is safe and backup again or will there be a raid damage as well? Thanks in advance. Regards.

    Read the article

  • ext4: error loading journal

    - by cloudyOutside
    I have an external hard drive with two partitions: A small FAT32 which is mostly empty and works fine and a large ext4 with tons of data, most of which isn't backed up. The ext4 is visible, but can't be mounted. I get an "error loading journal" error. The drive is a Western Digital Caviar Blue 500GB. Roughly 30GB of that is FAT32 and the rest is the ext4. The light on the enclosure turns red when reading from the bad partition. It was made by Cavalry. There wasn't any warning, but coincidentally, I've been thinking lately that I should get two large capacity drives for real backups. Is there anything that can be done? I'm not even sure I have enough storage to backup everything even if it is redeemable.

    Read the article

  • effective back-up using Raid / Win7 back-up

    - by Job
    I have a stand-alone pc system with two 2 tb harddiscs, one of which configured as Raid1, i.e. mirorring. The operational drive is partitioned. I use an external 1 tb harddisc for back-up using Windows 7 back-up facility which will be swapped weekly and stored on other premises. I back-up all partitions AND allow a system back-up. All application software is on the C: partition. Questions: How can I see whether Raid1 is working; i.e. is doing its job. All I see now is a status message in the start-up procedure that says its status is normal. How can I see used or available space on Raid 1? The Win-7 backup allows for 1 schedule only as far as I can see. I want daily back-ups of data. However due to the single schedule I am forced to do the time-consuming system back-up and c: back-up as well. Is there a way to activate two schedules allowing a frequent (daily) data back-up and a system back-up with c: drive back-up on a say weekly basis? Of course it can be forced by hand but I am likely to forget that. I am not the programming type of person so looking for simple and controllable solutions. Thank you - any help is apreciated.

    Read the article

  • How to enable password challenge in Active Directory?

    - by Antonio Laguna
    As IT Support, my team is taking so much time reseting passwords. So, we thought it would be interesting to enable some sort of Password Challenge in Active Directory so users could reset their own passwords, after correctly answering some questions. Despite we alert users by mail when their passwords are going to expire, they just delete the mail and go on so we think it should be a great idea. I've seen some commercial products but I'm not sure if there is something built-in or GPL to enable this kind of feature. Could someone shed some light about it?

    Read the article

  • Recover data from Dynamic Disk (MBR) bigger than 2TB

    - by Helder
    Here is the situation: Promise Array FastTrak TX4310 with 3 disks (750 GB each) in RAID5. This comes to around 1500 GB of data. Last week I had the idea of expanding the RAID with an additional 750 GB disk. This would bring the volume to around 2250 GB. I plugged the disk and used the Webpam software to do the RAID expansion. However, I didn't count with the MBR 2TB limit, as I didn't remembered that the disk was using MBR instead of GPT and I didn't check it prior to the expansion. After a couple of days of expansion, today when I got home, the disk in Windows disk manager showed the message "Invalid disk" and when I try to activate it, it says "The operation is not allowed on the Invalid pack". From what I figured, the logical volume on the RAID expanded, and passed that info to the Windows layer and I ended up with an "larger than 2TB" MBR disk. I'm hopping that somehow I can still recover some data from this, and I was wondering if I can "rewrite" the MBR structure back to the 1500 GB partition size, so I can access the partition in Windows. Right now I'm doing an "Analyse" with TestDisk, as I hope the program will pickup the old 1500 structure and allow me to somehow revert back to it. I think that even though the Logical Drive in the RAID is bigger than the 2TB, I can somehow correct the MBR to show the 1500 GB partition again. I had a similar problem once, and I was able to recover the data using a similar method. What do you guys think? Is it a dead end? Am I totally screwed because there is the extra RAID layer that I'm not counting? Or is there other way to move with this? Thanks all!

    Read the article

  • no administrator password for Windows 7

    - by huskergirl78
    I'm a secretary and my boss set up my new Windows 7 OptiPlex 7010 (Dell) computer for me while I was on vacation (he does not remember setting any "administrator" password). We are a small office so there is no system password set, either. I've used it for 6 months, all the while I couldn't access network drives, etc., without an administrator password. It was annoying, but I could still get my work done. Finally, on a slow day I took it upon myself to "fix" the problem, and in all my infinite wisdom, I managed to change my user account from administrator to standard user, so now I really can't do anything. I can't download or install any programs, move or rename files, etc. I tried the Dell suggested solution, but the BIOS tells me there is no password set, so it has to be a Windows 7 problem. All the solutions I have come across require an administrator password to let me do them. What can I do to find out the admin password so I can use my own darn computer!? Is there a default admin password?

    Read the article

  • My WD passport detected but not shown on my computer

    - by Rakesh Patel
    1TB WD harddisk is detected in laptop but drives not visible on my computer. Under disk managment drives shown without letters. Right clicking on these drives give 2 options: Delete volume Help. The same harddisk was running well on the same laptop a day before. It is also showing full size of hard drives, Healthy (Primary Partition) etc. (this happened after harddisk usage by guest). Harddisk is new only (about 5 month usage) Please suggest: Is there hardware related problem inside harddisk, if so is it repairable? Is there any option to recover data?

    Read the article

  • Any way to recover ext4 filesystems from a deleted LVM logical volume?

    - by Vegar Nilsen
    The other day I had a proper brain fart moment while expanding a disk on a Linux guest under Vmware. I stretched the Vmware disk file to the desired size and then I did what I usually do on Linux guests without LVM: I deleted the LVM partition and recreated it, starting in the same spot as the old one, but extended to the new size of the disk. (Which will be followed by fsck and resize2fs.) And then I realized that LVM doesn't behave the same way as ext2/3/4 on raw partitions... After restoring the Linux guest from the most recent backup (taken only five hours earlier, luckily) I'm now curious on how I could have recovered from the following scenario. It's after all virtually guaranteed that I'll be a dumb ass in the future as well. Virtual Linux guest with one disk, partitioned into one /boot (primary) partition (/dev/sda1) of 256MB, and the rest in a logical, extended partition (/dev/sda5). /dev/sda5 is then setup as a physical volume with pvcreate, and one volume group (vgroup00) created on top of it with the usual vgcreate command. vgroup00 is then split into two logical volumes root and swap, which are used for / and swap, logically. / is an ext4 file system. Since I had backups of the broken guest I was able to recreate the volume group with vgcfgrestore from the backup LVM setup found under /etc/lvm/backup, with the same UUID for the physical volume and all that. After running this I had two logical volumes with the same size as earlier, with 4GB free space where I had stretched the disk. However, when I tried to run "fsck /dev/mapper/vgroup00-root" it complained about a broken superblock. I tried to locate backup superblocks by running "mke2fs -n /dev/mapper/vgroup00-root" but none of those worked either. Then I tried to run TestDisk but when I asked it to find superblocks it only gave an error about not being able to open the file system due to a broken file system. So, with the default allocation policy for LVM2 in Ubuntu Server 10.04 64-bit, is it possible that the logical volumes are allocated from the end of the volume group? That would definitely explain why the restored logical volumes didn't contain the expected data. Could I have recovered by recreating /dev/sda5 with exactly the same size and disk position as earlier? Are there any other tools I could have used to find and recover the file system? (And clearly, the question is not whether or not I should have done this in a different way from the start, I know that. This is a question about what to do when shit has already hit the fan.)

    Read the article

  • Firefox: getting access to the list of tabs/windows to restore on startup

    - by robb
    Sometimes Firefox fails to restore the previously open tabs/windows. This might be happening when some of the URLs to be opened are no longer reachable (e.g. behind a VPN) or after the underlying OS (Windows) has been forcibly restarted (e.g. to complete an automated patch installation). Anyway, after restarting, can this list of URLs be recovered somehow? Say for example, I was daft enough to have clicked on "start new session". Can I still get access to the old list of open URLs? There is the browser history of course, but it contains a lot of stuff - the URLs that were open when Firefox last exited are not obvious. It would be neat if they were marked in some way - tagged for example.

    Read the article

  • MySQL Server - Got error -1 from storage engine

    - by Bobby
    I am currently trying to restore a MySQL table from the .ibd file. I have been following the instructions on the MySQL reference manual on how to use DISCARD and IMPORT TABLESPACE to replace the .idb files. Discarding the tablespace returns no error and the file is deleted however IMPORTING the replacement .ibd file yields a "Got error -1 from storage engine" error. There doesn't seem to be too much information about what exactly an error -1 is. Does anybody have any further insight as to why an import table space isn't working?

    Read the article

  • formated d partition by mistake

    - by duncan-benoit
    Hi there I just did a huge mistake. Yesterday, a freind of mine has asked me to intal windows xp for him. I did this task hundres of times, but yesterday i was tyred when i started the install procedure and i've formated the D partition and installed windows on it. Now I'm running PhotoRed on that partition, but it recovers the files in a weird way(filenames and diretory structure is lost). My questions are: 1) how can i recouver as much is possible from the previous data of that partition? 2) how to tell to my freind what i've did?

    Read the article

  • General High-Level Assessment

    - by tcarper
    Guys and Gals, I've been tasked with a doozy of an assignment. The objective is something akin to "laying of hands" on several database servers which work in concert to provide data to various Web, Client-Server and Tablet-Sync'd distributed Client-Server programs. More specifically, I've been asked to come up with a "Maintenance Plan" which includes recommendations for future work to improve these machines' performance/reliability/security/etc. Might there be some good articles on teh interwebs ya'll could point me towards which would give me some good basis to start? Articles describing "These are the top 4 overarching categories and this is how you should proceed when drilling down on each of them" sort-of-thing would be fabulous. The Databases are all SQL 2005, however the compatibility level is 80 and they were originally created with ERwin based on SQL 6.5. The OSs are all Windows Server 2003. Thanks all! Tim

    Read the article

  • machine crash when connecting to external harddisk

    - by Gnot
    i recently had a problem with my laptop. when i booted up the machine, i would get a SMART failure error message and when i pressed F1 to continue, it would take a very long time to boot and it would come back to the same error message again. thinking that my hard disk was dying, i bought a new hard disk and installed on my laptop and so now my laptop is alright. however i need to recover data from that old hard disk, so i bought an external hard disk case and placed the old hard disk onto the case and connected to my laptop with USB. the first few times when i connected, i could see the files from the old hard disk and managed to copy some files over although it took extremely long to transfer. but now whenever i connect to the old hard disk, after a few minutes, my laptop will crash and re-boot. do you think my old hard disk is dead beyond repair? or you can offer some help here? any assistance would be appreciated!

    Read the article

  • Different BSOD every time I turn on computer

    - by Gemboz
    Please help. Every time I turn on computer I receive a different BSOD. I can't even give my computer info because I haven't been able to stay on it long enough. The following are the BSOD that I just received in the last hour. IRQL_NOT_LESS_OR_EQUAL PAGE_FAULT_IN_NONPAGED_AREA BAD_POOL_HEADER MEMORY_MANAGEMENT I has also started with Windows Error Recovey which I have done but that has froze on me or hasn't helped. I have also reset computer to its original state. Now as soon as I turn on it goes to a BSOD almost immediately. I know you need more info about computer, so if you can tell me what info it is you need, I will get it. I can tell you that it is a desktop.

    Read the article

  • Forgotten LUKS passphrase

    - by Ansh David
    i am stuck with a big problem. I have encrypted my linux drive with LUKS and now I can't remember it. During boot, it prompts me for the passphrase, but I went into troubleshooting mode and deleted the entry from /etc/crypttab so at least I can boot now into my account but that doesn't solve the problem. I can't access my drive /dev/sda5. Can someone please show me a way to crack the passphrase or is there no way around it.

    Read the article

  • wusa in server 2008 R2

    - by Jack
    I need to use wusa to uninstall a particular update that is causing a reboot loop. I can access winre and dism, but wusa gives command not found. Does wusa not come with r2, or is it not available in the built-in WinRE or what?

    Read the article

  • Is it possible to configure TMG to impersonate a domain user for anonymous requests to a website?

    - by Daniel Root
    I would like to configure Forefront Threat Management Gateway (formerly ISA server) to impersonate a specific domain user for any anonymous request to a particular listener. For example, for any anonymous request to http://www.mycompany.com, I would like to serve up http://myinternal as though MYDOMAIN/GuestAccount were accessing the site. Is this even possible in ISA/TMG? If so, where do I go to configure this?

    Read the article

  • How do I make a partition usable in windows 7 after power loss?

    - by user1306322
    A few days ago I was installing some software and power went down. When I rebooted, the partition to which the software was installed was not accessible. Disk manager shows that it's there, but doesn't show type, if it's healthy and gives me an error when trying to read its properties. The problem seems to be common after power loss, people recommend solving it by assigning a letter to the partition via DiskPart utility, but partition isn't listed in my case. I can access that partition with bootable OSs (like bootable Ubuntu or winXP) and all the files are there, but another installation of Windows 7 gives me the same results as the original. I could just copy all data to another disk if there was enough space, but unfortunately the size of partition I'm having problems with is 1.1TB. How do I regain access to the partition in my original Windows 7 installation without losing any data?

    Read the article

  • XP can't read data from transferred HD

    - by Alexander Miller
    Computer A, running XP, died. XP was installed on a fresh HD in computer B. Slaved data-backup HD from A was installed as slave on B. B will not read it; shows only 2 folders, Recycler and System Volume Info. All of these are older machines with IDE drives. What's going on & how can I read/transfer the data from the transferred drive? This was only a trial run. Actually I will need to transfer the master HD from A - which has XP on it - and read from its data partition because (blush) the backup drive was not up to date.

    Read the article

  • Mounting LVM2 volume with XFS filesystem

    - by Chris
    Unfortunately I'm not able to access the data on my NAS anymore. I can't figure out why this is the case as I haven't changed anything. So I plugged one of the harddisks in my computer to access the data. What I did: kpartx -a /dev/sdc Now I should be able to access /dev/mapper/vg001-lv001 When trying to mount it I get: sudo mount -t xfs /dev/mapper/vg001-lv001 /home/user/mnt mount: /dev/mapper/vg001-lv001: can't read superblock Now I did a parted -l which gave me Modell: Linux device-mapper (linear) (dm) Festplatte /dev/mapper/vg001-lv001: 498GB Sektorgröße (logisch/physisch): 512B/512B Partitionstabelle: loop Number Begin End Size Filesystem Flags 1 0,00B 498GB 498GB xfs Does anybody have a solution how to recover the data?

    Read the article

< Previous Page | 51 52 53 54 55 56 57 58 59 60 61 62  | Next Page >