Search Results

Search found 15646 results on 626 pages for 'port 80'.

Page 551/626 | < Previous Page | 547 548 549 550 551 552 553 554 555 556 557 558  | Next Page >

• OSX: Mimic Ubuntu IP Masquerading via iptables with ipfw

  - by Dogbert

  Good day, I am attempting to replicate a setup I have between a router and an Ubuntu PC, and have the same setup working on my MacBook (10.6, Snow Leopard). First, I have a router that has a USB port. When I plug it into my Ubuntu PC, it creates an RNDIS connection, allowing me to connect to the router over the USB cable via an IP connection. When I plug it into my computer via USB, it gets assigned an IP address of 172.16.84.1, and a new adapter appears when I type ifconfig. I can then SSH into the device via ssh [email protected]. When I log in to the device, I flush the routes, then create the default route: admin@localhost> route -f admin@localhost> route add default 172.16.84.2 Now, in my Ubuntu machine, I use iptables to enable IP masquerading: root@Valhalla> sudo iptables -t nat -A POSTROUTING -s 172.16.84.2 -j MASQUERADE Once this is all done, the router has internet access over the USB connection to my PC. I am trying to replicate this exact setup on my MacBook now (Snow Leopard), but iptables does not exist for OSX, not even a Macports version exists. I have scoured through other questions on StackOverflow that cover the usage of the ipfw command, which apparently works as a drop-in replacement for iptables. However, the syntax is significantly different, and I'm pretty much lost. Does anyone with some experience with ipfw have some suggestions on how I could accomplish this and create a NAT connection via IP masquerading like I could with my Ubuntu PC? Thank you for your assistance.

  Read the article

• Issues with sustained traffic with PFSense

  - by Farseeker

  Last week we had to replace our PFSense firewall because it had a catastrophic hardware failure. All but one of the NICs were taken out of the old server and put into the new one. The one NIC that was not moved was the LAN NIC as this is on-board. The other NICs are all WAN connections and the must all be present (i.e. I can't disable one just for the sake of testing) After re-installing PFSense and restoring our backup of the configuration, everything came back online just fine, however on the new hardware any download that takes longer than about 10 seconds just times out in the middle. Example 1: Downloading from Microsoft.com goes at about 900k/sec and times out after about 10 seconds (thus, just under 10Mb of content) Example 2: Downloading from cnet.com goes at about 300k/sec and times out after about 10 seconds (thus, about 3Mb of content). By times out, I mean that the download just stops, and you have to pause/resume to get the next part done, repeat and rinse until the download is complete. However it's not consistant, sometimes it's 10 seconds, sometimes it's 4 seconds, and it sometimes you can't even load a heavy HTML page because the page never finishes. I assume this is most likely because PFSense does not like the onboard NIC, as this is the primary difference between the two servers. It's recognised as NFE0, and there's no room in the server for any more NICs and I don't have any dual-port NICs handy to experiment with a different LAN connection. I've never had to troubleshoot this sort of issue before. Can anyone give me some pointers about where to start? Linux is not my forte so please be kind!

  Read the article

• How can find the USB wireless adapter into the dmesg log file?

  - by AndreaNobili

  I am pretty new in Linux (RaspBian for RaspBerry Pi but I think that there are not difference) and I have to install an USB wireless network adapter (the product is the TP-Link TL-WN725N, this one: http://www.tp-link.it/products/details/?model=TL-WN725N ) Now, I think that this is not automatically recognized by my system because if I execute ifconfig command I obtain the following output: pi@raspberrypi ~ $ ifconfig eth0 Link encap:Ethernet HWaddr b8:27:eb:2a:9f:b0 inet addr:192.168.1.8 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:475 errors:0 dropped:0 overruns:0 frame:0 TX packets:424 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:34195 (33.3 KiB) TX bytes:89578 (87.4 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:65536 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) So now it see only my ethernet network interface and not the wireless. So I was thinkig to try to see into the dmesg, but I don't know what have I to see and how to select it into the dmesg output. For example by the following command I can see the line of the dmesg log file relate to my ethernet port: pi@raspberrypi ~ $ cat /var/log/dmesg |grep -i eth [ 3.177620] smsc95xx 1-1.1:1.0 eth0: register 'smsc95xx' at usb-bcm2708_usb-1.1, smsc95xx USB 2.0 Ethernet, b8:27:eb:2a:9f:b0 [ 18.030389] smsc95xx 1-1.1:1.0 eth0: hardware isn't capable of remote wakeup [ 19.642167] smsc95xx 1-1.1:1.0 eth0: link up, 100Mbps, full-duplex, lpa 0x45E1 But what can I try to search for the USB wireless adapter? Tnx

  Read the article

• can't Remote desktop to windows XP, blaming the server side

  - by Jin

  After rebooting my work PC (windows XP sp3) this Wednesday (thank to Microsoft Tuesday), I found that I can't remote desktop to my work PC from home (with VPN to company). I have been remote-desktop to work for years and I am really surprised since connectivity is not the problem, so I brought up wireshark to sniff the packets. I can see after TCP handshake, client sent X.224 Connection Request 03 00 00 13 0e e0 00 00 00 00 00 01 00 08 00 03 00 00 00 server sent X.224 Connection Confirm. 03 00 00 0b 06 d0 00 00 12 34 00 According to "MS-RDPBCGR", the official spec on RDP, the server should include Negotiation Response in the "Connection Confirm" message but it didn't. It's empty. I googled a lot but didn't find any clue on why server did that. By the way, I used the same remote desktop client and can connect to other windows XP PC. Here are a couple of pieces of information that may help to give a clue: Since TCP handshake (server port being 3389), I believe the svchost service is actually running. going to control panel -- system window, --- "Remote" tab, the remote desktop is indeeded checked and it states that my username is allowed. according to the packet capture, client didn't even get a chance to tell server what user was trying to logon. Yes, the progress bar showed up a few seconds and then it went back to the "Remote desktop Connection" window again. Searched "windowsupdate.log", didn't find any appearance of the word "remote".

  Read the article

• Apache2 with lighttpd as proxy

  - by andrzejp

  Hi, I am using apache2 as web server. I would like to help him lighttpd as a proxy for static content. Unfortunately I can not well set up lighttpd and apache2. (OS: Debian) Important things from lighttpd.config: server.modules = ( "mod_access", "mod_alias", "mod_accesslog", "mod_proxy", "mod_status", ) server.document-root = "/www/" server.port = 82 server.bind = "localhost" $HTTP["remoteip"] =~ "127.0.0.1" { alias.url += ( "/doc/" => "/usr/share/doc/", "/images/" => "/usr/share/images/" ) $HTTP["url"] =~ "^/doc/|^/images/" { dir-listing.activate = "enable" } } I would like to use lighttpd in only one site operating as a virtual directory on apache2. Configuration of this virtual directory: ProxyRequests Off ProxyPreserveHost On ProxyPass /images http://0.0.0.0:82/ ProxyPass /imagehosting http://0.0.0.0:82/ ProxyPass /pictures http://0.0.0.0:82/ ProxyPassReverse / http://0.0.0.0:82/ ServerName MY_VALUES ServerAlias www.MY_VALUES UseCanonicalName Off DocumentRoot /www/MYAPP/forum <Directory "/www/MYAPP/forum"> DirectoryIndex index.htm index.php AllowOverride None ... As you can see (or not;)) my service is physically located at the path: / www / myapp / forum and I would like to support lighttpd dealt with folders: / www / myapp / forum / images / www / myapp / forum / imagehosting / www / myapp / forum / pictures and left the rest (PHP scripts) for apache After running lighttpd and apache2 working party, but did not show up any images of these locations. What is wrong?

  Read the article

• can't get php mail() working on Ubuntu desktop version with sendmail and postfix

  - by user36428

  I'm running Ubuntu 9.10 LAMP and trying to do a simple email test with PHP and I'm not getting any emails sent. mail("[email protected]", "eric-linux test", "test") or die("can't send mail"); I get no errors from PHP when running that script. In my php.ini file is: sendmail_path = /usr/lib/sendmail -t -i $ sudo ps aux | grep sendmail eric 2486 0.0 0.4 8368 2344 pts/0 T 14:52 0:00 sendmail -s “Hello world” [email protected] eric 8747 0.0 0.3 5692 1616 pts/2 T 16:18 0:00 sendmail eric 8749 0.0 0.3 5692 1636 pts/2 T 16:18 0:00 sendmail start eric 9190 0.0 0.3 5692 1636 pts/2 T 19:12 0:00 sendmail start eric 9192 0.0 0.3 5692 1616 pts/2 T 19:12 0:00 sendmail eric 9425 0.0 0.3 5692 1620 pts/1 T 19:37 0:00 sendmail eric 9427 0.0 0.3 6584 1636 pts/1 T 19:37 0:00 sendmail restart eric 9429 0.0 0.3 5692 1636 pts/1 T 19:38 0:00 /usr/lib/sendmail restart eric 9432 0.0 0.1 3040 804 pts/1 R+ 19:38 0:00 grep --color=auto sendmail When I run $ sendmail start it just hangs there doing nothing. I installed postfix also to see if it would help, but it didn't. I tried to see port 25: eric@eric-linux:~$ telnet localhost 25 Trying ::1... Trying 127.0.0.1... Connected to localhost. Escape character is '^]'. 220 eric-linux ESMTP Postfix (Ubuntu) thanks

  Read the article

• Remote Desktop access Windows 7 system from Windows 8

  - by Prabhat

  I have 2 systems; Windows 7 & Windows 8. Both are connected to WiFi router. They have been assigned address 192.168.2.8 & 192.168.2.9 respectively. I have added them to home group. I am able to ping and connect Windows 8 system from Windows 7. I am having trouble connecting Windows 7 system from Windows 8 system. I can't even ping Windows 7 system. Windows 7 system's user is administrator (default administrator account from secpol.msc). File sharing, Remote Access, network discovery are all enabled. Someone please help me connect. EDIT : I found that this is the issue of Kaspersky Internet Security 2012. If I disable firewall, it works. I tried opening port 3389 in Kaspersky. It is still blocking access.

  Read the article

• Configuring DNS & MX records for exchange 2010

  - by Mahmoud Saleh

  i am trying to configure Exchange Server 2010 on Windows Server 2008 R2 to receive emails from the internet following the danscourses tutorials: and i followed this video for the DNS & MX records: http://www.youtube.com/watch?v=jdf_3DRssks i don't have any windows administration skills, and i am stuck with the DNS configuration. and the following are my domain configuration i got from the hosting. following are the steps i made: 1- Add new name server: add ns1.centors.com ip Exchange Server Public IP: 41.233.26.131 2- Change the A record change it to point to the public ip address Exchange Server Public IP: 41.233.26.131 3- New cname record for www and make it resolve to centors.com 4- New mx record for mail.centors.com 5- New A record for mail.centors.com: name: mail ip: Exchange Server Public IP: 41.233.26.131 6- new A record for ns1: ip: Exchange Server Public IP: 41.233.26.131 7- i made port forward in the router for SMTP and POP3 to the exchange server local ip address. ISSUE: i have a user account in the active directory, and the user is member of the domain, the user is [email protected] and when trying to login with this account in outlook 2010 on other machine using following data: account type: POP3 incoming mail server: mail.centors.com outgoing mail server: mail.centors.com i always get the error: Authorization failed, check your server settings. please advise what's wrong with the configuration, thanks in advance.

  Read the article

• OpenVPN: ERROR: could not read Auth username from stdin

  - by user56231

  I managed to setup openvpn but now I want to integrate a user/pass authentication method so, even though I haven't added the auth-nocache in the server config, whenever I try to connect it returns with the following message on the client side: ERROR: could not read Auth username from stdin My server.conf file contains basic stuff, everything works up untill I try to implement this for of authentication. mode server dev tun proto tcp port 1194 keepalive 10 120 plugin /usr/lib/openvpn/openvpn-auth-pam.so login client-cert-not-required username-as-common-name auth-user-pass-verify /etc/openvpn/auth.pl via-env ca /etc/openvpn/easy-rsa/2.0/keys/ca.crt cert /etc/openvpn/easy-rsa/2.0/keys/server.crt key /etc/openvpn/easy-rsa/2.0/keys/server.key dh /etc/openvpn/easy-rsa/2.0/keys/dh1024.pem user nobody group nogroup server 10.8.0.0 255.255.255.0 persist-key persist-tun #persist-local-ip status openvpn-status.log verb 3 client-to-client push "redirect-gateway def1" push "dhcp-option DNS 10.8.0.1" log-append /var/log/openvpn comp-lzo I searched all over the net for a solution and all answers seems to be related to the auth-nocache param which I haven't set. The directive auth-user-pass-verify /etc/openvpn/auth.pl via-env points to a script which is executed to perform the authentication. A false authentication should result in a exit 1 while a true one should result with exit 0. For testing, that script auth.pl returns exit 0 no matter what the input is but it seems that the file is not executed before the error raises. auth.pl file contents: #!/usr/bin/perl my $user = $ENV{username}; my $passwd = $ENV{password}; printf("$user : $passwd\n"); exit 0; Any ideas?

  Read the article

• Problem using a public key when connecting to a SSH server running on Cygwin

  - by Deleted

  We have installed Cygwin on a Windows Server 2008 Standard server and it working pretty well. Unfortunately we still have a big problem. We want to connect using a public key through SSH which doesn't work. It always falls back to using password login. We have appended our public key to ~/.ssh/authorized_keys on the server and we have our private and public key in ~/.ssh/id_dsa respective ~/.ssh/id_dsa.pub on the client. When debugging the SSH login session we see that the key is offered by the server apparently rejects it by some unknown reason. The SSH output when connecting from an Ubuntu 9.10 desktop with debug information enabled: $ ssh -v 192.168.10.11 OpenSSH_5.1p1 Debian-6ubuntu2, OpenSSL 0.9.8g 19 Oct 2007 debug1: Reading configuration data /home/myuseraccount/.ssh/config debug1: Reading configuration data /etc/ssh/ssh_config debug1: Applying options for debug1: Connecting to 192.168.10.11 [192.168.10.11] port 22. debug1: Connection established. debug1: identity file /home/myuseraccount/.ssh/identity type -1 debug1: identity file /home/myuseraccount/.ssh/id_rsa type -1 debug1: identity file /home/myuseraccount/.ssh/id_dsa type 2 debug1: Checking blacklist file /usr/share/ssh/blacklist.DSA-1024 debug1: Checking blacklist file /etc/ssh/blacklist.DSA-1024 debug1: Remote protocol version 2.0, remote software version OpenSSH_5.3 debug1: match: OpenSSH_5.3 pat OpenSSH debug1: Enabling compatibility mode for protocol 2.0 debug1: Local version string SSH-2.0-OpenSSH_5.1p1 Debian-6ubuntu2 debug1: SSH2_MSG_KEXINIT sent debug1: SSH2_MSG_KEXINIT received debug1: kex: server->client aes128-cbc hmac-md5 none debug1: kex: client->server aes128-cbc hmac-md5 none debug1: SSH2_MSG_KEX_DH_GEX_REQUEST(1024<1024<8192) sent debug1: expecting SSH2_MSG_KEX_DH_GEX_GROUP debug1: SSH2_MSG_KEX_DH_GEX_INIT sent debug1: expecting SSH2_MSG_KEX_DH_GEX_REPLY debug1: Host '192.168.10.11' is known and matches the RSA host key. debug1: Found key in /home/myuseraccount/.ssh/known_hosts:12 debug1: ssh_rsa_verify: signature correct debug1: SSH2_MSG_NEWKEYS sent debug1: expecting SSH2_MSG_NEWKEYS debug1: SSH2_MSG_NEWKEYS received debug1: SSH2_MSG_SERVICE_REQUEST sent debug1: SSH2_MSG_SERVICE_ACCEPT received debug1: Authentications that can continue: publickey,password,keyboard-interactive debug1: Next authentication method: publickey debug1: Offering public key: /home/myuseraccount/.ssh/id_dsa debug1: Authentications that can continue: publickey,password,keyboard-interactive debug1: Trying private key: /home/myuseraccount/.ssh/identity debug1: Trying private key: /home/myuseraccount/.ssh/id_rsa debug1: Next authentication method: keyboard-interactive debug1: Authentications that can continue: publickey,password,keyboard-interactive debug1: Next authentication method: password [email protected]'s password: The version of Cygwin: $ uname -a CYGWIN_NT-6.0 servername 1.7.1(0.218/5/3) 2009-12-07 11:48 i686 Cygwin The installed packages: $ cygcheck -c Cygwin Package Information Package Version Status _update-info-dir 00871-1 OK alternatives 1.3.30c-10 OK arj 3.10.22-1 OK aspell 0.60.5-1 OK aspell-en 6.0.0-1 OK aspell-sv 0.50.2-2 OK autossh 1.4b-1 OK base-cygwin 2.1-1 OK base-files 3.9-3 OK base-passwd 3.1-1 OK bash 3.2.49-23 OK bash-completion 1.1-2 OK bc 1.06-2 OK bzip2 1.0.5-10 OK cabextract 1.1-1 OK compface 1.5.2-1 OK coreutils 7.0-2 OK cron 4.1-59 OK crypt 1.1-1 OK csih 0.9.1-1 OK curl 7.19.6-1 OK cvs 1.12.13-10 OK cvsutils 0.2.5-1 OK cygrunsrv 1.34-1 OK cygutils 1.4.2-1 OK cygwin 1.7.1-1 OK cygwin-doc 1.5-1 OK cygwin-x-doc 1.1.0-1 OK dash 0.5.5.1-2 OK diffutils 2.8.7-2 OK doxygen 1.6.1-2 OK e2fsprogs 1.35-3 OK editrights 1.01-2 OK emacs 23.1-10 OK emacs-X11 23.1-10 OK file 5.04-1 OK findutils 4.5.5-1 OK flip 1.19-1 OK font-adobe-dpi75 1.0.1-1 OK font-alias 1.0.2-1 OK font-encodings 1.0.3-1 OK font-misc-misc 1.1.0-1 OK fontconfig 2.8.0-1 OK gamin 0.1.10-10 OK gawk 3.1.7-1 OK gettext 0.17-11 OK gnome-icon-theme 2.28.0-1 OK grep 2.5.4-2 OK groff 1.19.2-2 OK gvim 7.2.264-1 OK gzip 1.3.12-2 OK hicolor-icon-theme 0.11-1 OK inetutils 1.5-6 OK ipc-utils 1.0-1 OK keychain 2.6.8-1 OK less 429-1 OK libaspell15 0.60.5-1 OK libatk1.0_0 1.28.0-1 OK libaudio2 1.9.2-1 OK libbz2_1 1.0.5-10 OK libcairo2 1.8.8-1 OK libcurl4 7.19.6-1 OK libdb4.2 4.2.52.5-2 OK libdb4.5 4.5.20.2-2 OK libexpat1 2.0.1-1 OK libfam0 0.1.10-10 OK libfontconfig1 2.8.0-1 OK libfontenc1 1.0.5-1 OK libfreetype6 2.3.12-1 OK libgcc1 4.3.4-3 OK libgdbm4 1.8.3-20 OK libgdk_pixbuf2.0_0 2.18.6-1 OK libgif4 4.1.6-10 OK libGL1 7.6.1-1 OK libglib2.0_0 2.22.4-2 OK libglitz1 0.5.6-10 OK libgmp3 4.3.1-3 OK libgtk2.0_0 2.18.6-1 OK libICE6 1.0.6-1 OK libiconv2 1.13.1-1 OK libidn11 1.16-1 OK libintl3 0.14.5-1 OK libintl8 0.17-11 OK libjasper1 1.900.1-1 OK libjbig2 2.0-11 OK libjpeg62 6b-21 OK libjpeg7 7-10 OK liblzma1 4.999.9beta-10 OK libncurses10 5.7-18 OK libncurses8 5.5-10 OK libncurses9 5.7-16 OK libopenldap2_3_0 2.3.43-1 OK libpango1.0_0 1.26.2-1 OK libpcre0 8.00-1 OK libpixman1_0 0.16.6-1 OK libpng12 1.2.35-10 OK libpopt0 1.6.4-4 OK libpq5 8.2.11-1 OK libreadline6 5.2.14-12 OK libreadline7 6.0.3-2 OK libsasl2 2.1.19-3 OK libSM6 1.1.1-1 OK libssh2_1 1.2.2-1 OK libssp0 4.3.4-3 OK libstdc++6 4.3.4-3 OK libtiff5 3.9.2-1 OK libwrap0 7.6-20 OK libX11_6 1.3.3-1 OK libXau6 1.0.5-1 OK libXaw3d7 1.5D-8 OK libXaw7 1.0.7-1 OK libxcb-render-util0 0.3.6-1 OK libxcb-render0 1.5-1 OK libxcb1 1.5-1 OK libXcomposite1 0.4.1-1 OK libXcursor1 1.1.10-1 OK libXdamage1 1.1.2-1 OK libXdmcp6 1.0.3-1 OK libXext6 1.1.1-1 OK libXfixes3 4.0.4-1 OK libXft2 2.1.14-1 OK libXi6 1.3-1 OK libXinerama1 1.1-1 OK libxkbfile1 1.0.6-1 OK libxml2 2.7.6-1 OK libXmu6 1.0.5-1 OK libXmuu1 1.0.5-1 OK libXpm4 3.5.8-1 OK libXrandr2 1.3.0-10 OK libXrender1 0.9.5-1 OK libXt6 1.0.7-1 OK links 1.00pre20-1 OK login 1.10-10 OK luit 1.0.5-1 OK lynx 2.8.5-4 OK man 1.6e-1 OK minires 1.02-1 OK mkfontdir 1.0.5-1 OK mkfontscale 1.0.7-1 OK openssh 5.4p1-1 OK openssl 0.9.8m-1 OK patch 2.5.8-9 OK patchutils 0.3.1-1 OK perl 5.10.1-3 OK rebase 3.0.1-1 OK run 1.1.12-11 OK screen 4.0.3-5 OK sed 4.1.5-2 OK shared-mime-info 0.70-1 OK tar 1.22.90-1 OK terminfo 5.7_20091114-13 OK terminfo0 5.5_20061104-11 OK texinfo 4.13-3 OK tidy 041206-1 OK time 1.7-2 OK tzcode 2009k-1 OK unzip 6.0-10 OK util-linux 2.14.1-1 OK vim 7.2.264-2 OK wget 1.11.4-4 OK which 2.20-2 OK wput 0.6.1-2 OK xauth 1.0.4-1 OK xclipboard 1.1.0-1 OK xcursor-themes 1.0.2-1 OK xemacs 21.4.22-1 OK xemacs-emacs-common 21.4.22-1 OK xemacs-sumo 2007-04-27-1 OK xemacs-tags 21.4.22-1 OK xeyes 1.1.0-1 OK xinit 1.2.1-1 OK xinput 1.5.0-1 OK xkbcomp 1.1.1-1 OK xkeyboard-config 1.8-1 OK xkill 1.0.2-1 OK xmodmap 1.0.4-1 OK xorg-docs 1.5-1 OK xorg-server 1.7.6-2 OK xrdb 1.0.6-1 OK xset 1.1.0-1 OK xterm 255-1 OK xz 4.999.9beta-10 OK zip 3.0-11 OK zlib 1.2.3-10 OK zlib-devel 1.2.3-10 OK zlib0 1.2.3-10 OK The ssh deamon configuration file: $ cat /etc/sshd_config # $OpenBSD: sshd_config,v 1.80 2008/07/02 02:24:18 djm Exp $ # This is the sshd server system-wide configuration file. See # sshd_config(5) for more information. # This sshd was compiled with PATH=/bin:/usr/sbin:/sbin:/usr/bin # The strategy used for options in the default sshd_config shipped with # OpenSSH is to specify options with their default value where # possible, but leave them commented. Uncommented options change a # default value. Port 22 #AddressFamily any #ListenAddress 0.0.0.0 #ListenAddress :: # Disable legacy (protocol version 1) support in the server for new # installations. In future the default will change to require explicit # activation of protocol 1 Protocol 2 # HostKey for protocol version 1 #HostKey /etc/ssh_host_key # HostKeys for protocol version 2 #HostKey /etc/ssh_host_rsa_key #HostKey /etc/ssh_host_dsa_key # Lifetime and size of ephemeral version 1 server key #KeyRegenerationInterval 1h #ServerKeyBits 1024 # Logging # obsoletes QuietMode and FascistLogging #SyslogFacility AUTH #LogLevel INFO # Authentication: #LoginGraceTime 2m #PermitRootLogin yes StrictModes no #MaxAuthTries 6 #MaxSessions 10 RSAAuthentication yes PubkeyAuthentication yes AuthorizedKeysFile .ssh/authorized_keys # For this to work you will also need host keys in /etc/ssh_known_hosts #RhostsRSAAuthentication no # similar for protocol version 2 #HostbasedAuthentication no # Change to yes if you don't trust ~/.ssh/known_hosts for # RhostsRSAAuthentication and HostbasedAuthentication #IgnoreUserKnownHosts no # Don't read the user's ~/.rhosts and ~/.shosts files #IgnoreRhosts yes # To disable tunneled clear text passwords, change to no here! #PasswordAuthentication yes #PermitEmptyPasswords no # Change to no to disable s/key passwords #ChallengeResponseAuthentication yes # Kerberos options #KerberosAuthentication no #KerberosOrLocalPasswd yes #KerberosTicketCleanup yes #KerberosGetAFSToken no # GSSAPI options #GSSAPIAuthentication no #GSSAPICleanupCredentials yes # Set this to 'yes' to enable PAM authentication, account processing, # and session processing. If this is enabled, PAM authentication will # be allowed through the ChallengeResponseAuthentication and # PasswordAuthentication. Depending on your PAM configuration, # PAM authentication via ChallengeResponseAuthentication may bypass # the setting of "PermitRootLogin without-password". # If you just want the PAM account and session checks to run without # PAM authentication, then enable this but set PasswordAuthentication # and ChallengeResponseAuthentication to 'no'. #UsePAM no AllowAgentForwarding yes AllowTcpForwarding yes GatewayPorts yes X11Forwarding yes X11DisplayOffset 10 X11UseLocalhost no #PrintMotd yes #PrintLastLog yes TCPKeepAlive yes #UseLogin no UsePrivilegeSeparation yes #PermitUserEnvironment no #Compression delayed #ClientAliveInterval 0 #ClientAliveCountMax 3 #UseDNS yes #PidFile /var/run/sshd.pid #MaxStartups 10 #PermitTunnel no #ChrootDirectory none # no default banner path #Banner none # override default of no subsystems Subsystem sftp /usr/sbin/sftp-server # Example of overriding settings on a per-user basis #Match User anoncvs #X11Forwarding yes #AllowTcpForwarding yes #ForceCommand cvs server I hope this information is enough to solve the problem. In case any more is needed please comment and I'll add it. Thank you for reading!

  Read the article

• HP Procurve 2610 intervlan routing

  - by user19039

  Can anyone tell me why inter vlan routing is working for all vlans except my newly created vlan 4/ I have an hp procurve 2610. Any help would be appreciated. I have basically this 1 switch with all unmanaged switches attached to the core. We have a second 2610 on port 28 Running configuration: ; J9085A Configuration Editor; Created on release #R.11.25 hostname "Core_HP" interface 22 speed-duplex 100-full exit ip routing snmp-server community "public" Unrestricted vlan 1 name "DEFAULT_VLAN" untagged 1-12,17-22,26-27 ip address 192.168.4.6 255.255.255.0 tagged 25 no untagged 13-16,23-24,28 exit vlan 2 name "WAN" untagged 28 ip address 10.254.254.3 255.255.255.0 exit vlan 3 name "Wireless" untagged 13-16,24 ip address 192.168.7.6 255.255.255.0 ip helper-address 192.168.4.2 tagged 27 exit vlan 35 name "guest" untagged 23 tagged 24 exit vlan 4 name "esxi" untagged 25 ip address 10.10.1.1 255.255.248.0 exit ip route 192.168.5.0 255.255.255.0 10.254.254.1 ip route 192.168.6.0 255.255.255.0 10.254.254.1 ip route 0.0.0.0 0.0.0.0 192.168.4.10 show ip route IP Route Entries Destination Gateway VLAN Type Sub-Type M etric Dist. ------------------ --------------- ---- --------- ---------- - --------- ----- 0.0.0.0/0 192.168.4.10 1 static 1 1 10.10.0.0/21 esxi 4 connected 0 0 10.254.254.0/24 WAN 2 connected 0 0 127.0.0.0/8 reject static 0 250 127.0.0.1/32 lo0 connected 0 0 192.168.4.0/24 DEFAULT_VLAN 1 connected 0 0 192.168.5.0/24 10.254.254.1 2 static 1 1 192.168.6.0/24 10.254.254.1 2 static 1 1 192.168.7.0/24 Wireless 3 connected 0 0 show ip Internet (IP) Service IP Routing : Enabled Default TTL : 64 Arp Age : 20 VLAN | IP Config IP Address Subnet Mask Prox y ARP ------------ + ---------- --------------- --------------- ---- ----- DEFAULT_VLAN | Manual 192.168.4.6 255.255.255.0 No WAN | Manual 10.254.254.3 255.255.255.0 No Wireless | Manual 192.168.7.6 255.255.255.0 No esxi | Manual 10.10.1.1 255.255.248.0 No guest | Disabled

  Read the article

• Apple Service Diagnostic application on USB key?

  - by Matt 'Trouble' Esse

  I found the following in a text file, and I would like to use the Apple Service Diagnostic Application from a bootable USB key but I cannot find where to download it or set it up? Also is this free software or does it require a separate licence? It sounds like it would be a useful tool for diagnosing Mac problems. The Apple Service Diagnostic application is designed to run both EFI and Mac OS X tests from an external USB hard drive. Apple Service Diagnostic (EFI) runs low-level tests of the hardware directly and does not require Mac OS X, while Apple Service Diagnostic (OS) uses Mac OS X to run tests. Booting and Using the Apple Service Diagnostic Application - Before using Apple Service Diagnostic, disconnect any Ethernet network, USB, and audio cables. - With the USB hard drive containing ASD 3S123 plugged into a USB port, restart the computer and hold down the option key as the computer boots up into the Startup Manager. To run ASD (EFI) select the "ASD EFI 3S123" drive icon and press return or select it with a mouse click. To run ASD (OS) select the "ASD OS 3S123" drive icon and press return or select it with a mouse click. ASD (EFI) will load in 20-30 seconds; ASD (OS) will load in 2-3 minutes. - After running ASD (OS) or ASD (EFI), press the Restart button to restart the computer back into the normal startup volume, or hold down the option key to get back to the Startup Manager. ASD is no longer delivered as an image to be restored onto a DVD. ASD 3S117 and newer versions requires installation onto an external USB hard drive. For more information, please refer to the document "Installing ASD on a USB hard drive".

  Read the article

• USB keyboard stopped working in Ubuntu with error -71

  - by tapan

  I have a usb keyboard which was working perfectly till now (about a year since i have been regularly using ubuntu). It suddenly stopped working. It stopped working when I connected a USB HDD. Now the keyboard works randomly .. working for a while and then stops working for a longer time. Here is the dmesg output : [ 705.817076] usb 5-1: device not accepting address 8, error -71 [ 705.928032] usb 5-1: new low speed USB device using uhci_hcd and address 9 [ 706.336060] usb 5-1: device not accepting address 9, error -71 [ 706.448055] usb 5-1: new low speed USB device using uhci_hcd and address 10 [ 706.568044] usb 5-1: device descriptor read/64, error -71 [ 706.792049] usb 5-1: device descriptor read/64, error -71 [ 707.008060] usb 5-1: new low speed USB device using uhci_hcd and address 11 [ 707.128041] usb 5-1: device descriptor read/64, error -71 [ 707.352052] usb 5-1: device descriptor read/64, error -71 [ 707.456068] hub 5-0:1.0: unable to enumerate USB device on port 1 Based on the suggestions here i tried the following two things: echo -1 > /sys/module/usbcore/parameters/autosuspend echo Y > /sys/module/usbcore/parameters/old_scheme_first However, i am still facing the same problem. Can anyone help me out with this ? I'm using Ubuntu 10.04 Lucid Lynx.

  Read the article

• fail2ban log parsing too slow on Raspberry Pi - options? [migrated]

  - by Gordon Morehouse

  I'm running fail2ban on a Raspberry Pi at 950MHz which I cannot overclock further. The Pi is occasionally subject to SYN floods on particular ports. I've set up iptables to throttle the rate of SYNs on the port of interest; when the throttle limits are exceeded, hosts which send SYNs are dropped into the REJECT chain and the particular SYN packet which exceeded the limit is logged. fail2ban then watches for these logged SYNs and, after seeing a few, temporarily bans the host for a short time (this is a transient issue in the app I'm working with). The problem is that the SYN floods can occasionally reach rates which are too fast for fail2ban to keep up with; I'll see 20-40 log messages per second, and eventually fail2ban falls behind and becomes ineffective. To add insult to injury, it continues consuming a LOT of CPU as it tries to catch up. I have verified that DROP chained packets from hosts already banned by fail2ban are not logged, and thus do not add to its load. What are my options here? I have a few ideas, but no clear path forward. Could I make the log-parse regex "easier" so it takes fewer cycles? Would using iptables --log-prefix to put a token near the start of the log message, and/or otherwise simplifying/altering the fail2ban regex help? Here is the current fail2ban config line containing a regex: failregex = kernel:.*?SRC=(?:::f{4,6}:)?(?P<host>[\w\-.^_]+) DST.*?SYN Is there a faster way for fail2ban to watch for the packets exceeding the limits than parsing kern.log? Could fail2ban be run under PyPy instead of CPython with minimal nonstandard wizardry (the OS is Raspbian 7, so, mostly Debian 7)? Is there something better than fail2ban that I could use to watch for the packets which exceed the SYN limits, and after N exceeds in X seconds, temporarily put the offending IP into the iptables DROP bucket, and take it out when the ban timer expires? Again, I'd vastly prefer a solution that uses as much software available in Debian as possible, though I can build Debian packages in a pinch.

  Read the article

• Joining an Ubuntu 14.04 machine to active directory with realm and sssd

  - by tubaguy50035

  I've tried following this guide to set up realmd and sssd with active directory: http://funwithlinux.net/2014/04/join-ubuntu-14-04-to-active-directory-domain-using-realmd/ When I run the command realm –verbose join domain.company.com –user-principal=c-u14-dev1/[email protected] –unattended everything seems to connect. My sssd.conf looks like the following: [nss] filter_groups = root filter_users = root reconnection_retries = 3 [pam] reconnection_retries = 3 [sssd] domains = DOMAIN.COMPANY.COM config_file_version = 2 services = nss, pam [domain/DOMAIN.COMPANY.COM] ad_domain = DOMAIN.COMPANY.COM krb5_realm = DOMAIN.COMPANY.COM realmd_tags = manages-system joined-with-adcli cache_credentials = True id_provider = ad krb5_store_password_if_offline = True default_shell = /bin/bash ldap_id_mapping = True use_fully_qualified_names = True fallback_homedir = /home/%d/%u access_provider = ad My /etc/pam.d/common-auth looks like this: auth [success=3 default=ignore] pam_krb5.so minimum_uid=1000 auth [success=2 default=ignore] pam_unix.so nullok_secure try_first_pass auth [success=1 default=ignore] pam_sss.so use_first_pass # here's the fallback if no module succeeds auth requisite pam_deny.so # prime the stack with a positive return value if there isn't one already; # this avoids us returning an error just because nothing sets a success code # since the modules above will each just jump around auth required pam_permit.so # and here are more per-package modules (the "Additional" block) auth optional pam_cap.so However, when I try to SSH into the machine with my active directory user, I see the following in auth.log: Aug 21 10:35:59 c-u14-dev1 sshd[11285]: Invalid user nwalke from myip Aug 21 10:35:59 c-u14-dev1 sshd[11285]: input_userauth_request: invalid user nwalke [preauth] Aug 21 10:36:10 c-u14-dev1 sshd[11285]: pam_krb5(sshd:auth): authentication failure; logname=nwalke uid=0 euid=0 tty=ssh ruser= rhost=myiphostname Aug 21 10:36:10 c-u14-dev1 sshd[11285]: pam_unix(sshd:auth): check pass; user unknown Aug 21 10:36:10 c-u14-dev1 sshd[11285]: pam_unix(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=myiphostname Aug 21 10:36:10 c-u14-dev1 sshd[11285]: pam_sss(sshd:auth): authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=myiphostname user=nwalke Aug 21 10:36:10 c-u14-dev1 sshd[11285]: pam_sss(sshd:auth): received for user nwalke: 10 (User not known to the underlying authentication module) Aug 21 10:36:12 c-u14-dev1 sshd[11285]: Failed password for invalid user nwalke from myip port 34455 ssh2 What do I need to do to allow active directory users the ability to log in?

  Read the article

• Fetch videos from sony handycam to linux

  - by bstpierre

  I've got a Sony Handycam DCR-DVD101. When I plug connect the USB cable to my laptop (Ubuntu 10) it doesn't mount any storage device. If I run usb-devices, I see: T: Bus=02 Lev=02 Prnt=02 Port=00 Cnt=01 Dev#= 6 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=054c ProdID=00c1 Rev=01.00 S: Manufacturer=SONY S: Product=Storage Device C: #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr=2mA I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=05 Prot=50 Driver=usb-storage The driver says usb-storage, but I'm not sure how to get the device mounted. Is there a way to make this work? Update: checking dmesg, I see: [259072.576559] usb 2-1.1: new high speed USB device using ehci_hcd and address 6 [259072.687200] usb 2-1.1: configuration #1 chosen from 1 choice [259072.836188] Initializing USB Mass Storage driver... [259072.836476] scsi5 : SCSI emulation for USB Mass Storage devices [259072.836632] usb-storage: device found at 6 [259072.836636] usb-storage: waiting for device to settle before scanning [259072.836660] usbcore: registered new interface driver usb-storage [259072.836666] USB Mass Storage support registered. [259077.830410] usb-storage: device scan complete [259077.832343] scsi 5:0:0:0: CD-ROM SONY DDX-A1010 R1.0 PQ: 0 ANSI: 0 [259077.888167] sr1: scsi3-mmc drive: 0x/0x pop-up [259077.888446] sr 5:0:0:0: Attached scsi CD-ROM sr1 [259077.888593] sr 5:0:0:0: Attached scsi generic sg2 type 5 [259080.002079] sr 5:0:0:0: [sr1] Unhandled sense code [259080.002085] sr 5:0:0:0: [sr1] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE [259080.002091] sr 5:0:0:0: [sr1] Sense Key : Blank Check [current] [259080.002097] sr 5:0:0:0: [sr1] Add. Sense: No additional sense information [259080.002104] sr 5:0:0:0: [sr1] CDB: Read(10): 28 00 00 00 00 00 00 00 02 00 00 00 [259080.002117] end_request: I/O error, dev sr1, sector 0 [259080.002123] Buffer I/O error on device sr1, logical block 0 [259080.002128] Buffer I/O error on device sr1, logical block 1 Those I/O errors don't look good, is there any hope?

  Read the article

• Keep-Alive header not sent from Tomcat 5.5 http connector?

  - by Codek

  We're currently using a hardware load balancer, which then goes to Apache and that then goes to Tomcat 5.5 via the AJP connector. We've decided to dump apache for various reasons - In our current system it doesnt provide any advantage. However when I look at the headers sent when we do this, the "Keep-Alive: timeout=15 max=96" header doesnt get sent when you use the tomcat http connector Interestingly, i can find no documentiation on "keepalivetimeout" for tomcat5.5, but i can for tomcat6. But neither can i find evidence that tomcat5.5 doesnt support this setting. here's my connector: <Connector port="8090" maxHttpHeaderSize="8192" maxThreads="400" minSpareThreads="150" maxSpareThreads="300" enableLookups="false" connectionTimeout="2" maxKeepAliveRequests="400" disableUploadTimeout="true" /> So; Is there any way I can specify the keepalive timeout if we use the http connector with tomcat 5.5, and force this header entry to be sent? Just to be clear - the exact header entry i see back from the server is this with apache: Keep-Alive: timeout=2, max=100 But nothing from tomcat/coyote. I've looked at this some more, and I dont think the Keep-Alive header entry really matters. The problem seems to be that keep-alives are simply not supported in tomcat 5.5 http connector? They do seem to work in tomcat6 (+java 6). Thanks, Dan

  Read the article

• two computers on same network cannot ping eachother nor view NetBios resources

  - by slava

  I'd like to find out the problem of my network configuration I have network configuration is like in this diagram: The problem is between laptop1 and laptop2. At first I thought it was samba server problem. I was configuring samba server on one of the laptops and I wasn't able to access the shares from the second laptop no matter what I was doing. After installing/removing/configuring samba-server a couple of times I realized that the problem resides somewhere else. Laptop configurations: - Laptop1: ubuntu 12.04 - Laptop2: Windows 7/ ubuntu 12.04 ( dual boot ) - Server : ubuntu 12.04 When I do "ping 192.168.0.10" from laptop2, I get "Destination host unreachable". The same situation is when I ping in other direction. When I access Laptop1 shares from Laptop2, having windows 7 loaded, I get the error message: "Error code: 0x80070035 The network path was not found." When I ping "server" or "router" or "wifi router" from any of laptops I get a reply. The same with windows shares, I am able to access "server"s shares from Windows and Ubuntu, from any of my laptops. Netbios can't function correctly, that's obvious, I am unable to access windows shares between laptops. I assume that on "wifi router" is a miss-configuration, but I can't find what specifically. The "Wifi router" works as Hub + wifi, it is connected to "router" not in WAN port but in LAN1. Please, help me correctly configure the router to make them see each-other, or at least make NetBios work correctly, between laptops, to be able to access windows shares. Thanks!

  Read the article

• Installation of Active Directory on separate VM from DNS does not entierly work - not sure why

  - by René Kåbis

  Not sure what I am doing wrong here. I have a moderately midrange server (16 cores, 2Ghz, 32GB ECC REG RAM, 6TB storage, nothing too extreme) where I am running Hyper-V (Server 2012 R2 Enterprise) in order to provision virtual machines. So why an AD separate from DNS? I want redundancy. I want to be able to move VMs and back them up individually and not have too many services on any one VM. I have already provisioned a VM with DNS, and have set it up right -- essentially, I have: Set up Static IP’s for everyone involved. Installed the DNS service on the DNS VM. Created a forward lookup zone and a reverse lookup zone (primary zone) xyz.ca Configured the zones to use nonsecure and secure dynamic updates (i will change this to secure later after the domain controller is online). Created a A record for the DC in the forward lookup zone (and a reverse ptr) Changed DC’s DNS server (network settings) to the new DNS server. Checked that I can ping the dns server from the new DC by hostname. When I went ahead and did a DCpromo on the DC, and un-cheked the “install DNS” option, everything seemed to go well (no error messages), but I saw no changes on the DNS server whatsoever (no additional settings). Plus, the DNS server seems to be unable to join the domain, as it claims that the domain is not discoverable. As a final note, I do run Symantec Endpoint Protection, which includes a firewall and most settings set as default. I have not yet tried turning this off, but my experience has been that if a service would open up a port on a Windows firewall, it would do the same through Symantec. There is pretty tight integration these days with corporate-class AV and Windows. I have a template vhdx fully set up (just short of any special roles and features) that I can use to replace the current AD VM with, so doing this all over again is not too much skin off of my nose.

  Read the article

• iRedMail home setup - use different SMTP relay for different destination domains

  - by John

  Hello helpful server folks, I'm messing with iRedMail. I've mostly been successful, I think I have an SMTP problem. I have changed RoundCube (webmail) to use BrightHouse's, my ISP's, SMTP server for outgoing. It works fine, I click send and poof, I have gmail. I can reply from gmail to my email server, and it works. It took 10 hours for the email to show up, which is a different problem, I think, but it does work. But when I send from my server TO my own server, my ISP's Postmaster account sends me a cryptic blurb. I just got off the phone with them, and they say it "should work", and that they can't reach my pop3 server. (pop3, pop3s, imap, and imaps are all open on my router and forwarded to the server, I'm not sure what I need, I'm just covering my bases...) pop3 and/or imap as external interfaces are just formalities, I really just want webmail to work. Roundcube only takes one SMTP server in its configs. How can I configure Postfix to relay / forward emails to my ISP's SMTP, while taking messages bound for my own domain and processing them? Since my ISP won't let me "bounce" my emails off of it. Maybe I'm vastly misunderstanding how e-mail works in general: To receive mail, I should only need port 25, SMTP, open to the internet, correct? Should I be concerned about some authentication failure from the outside to my relay? (My relay requires user/pass to use, my ISP's requires none.)

  Read the article

• Intel DriverInstall issue on HP ProLiant server DL580G5

  - by TomTom

  Given: A HP ProLiant server to be used for Hyper-V server (R 2) Problem: The server has a HP NC364T quad port card, which actually is an Intel 1000 Pro adapter. We are stuck getting this adapter properly working. We need to get it working with: 2 trunks of 2 ports each one of them fully vlan "aware" (without filtering anything - so that Hyper-V can do the VLAN filtering). So far we did: Install the server Install latest PSP. Problem here - tool does not work to set up teaming. We tried to install the latest ProWin pack from Intel - the drivers there are a LOT more current (26th of Marrch 2010, 9.13.41.0). The intalled driver (Microsoft) is ancient (march 2009, 9.13.4.10) A driver update fails both on command line (pnputil) as well as the PortLock device manager executable. No informatoin is provided. the ANS toolset can not create teams (fails with error - again, no reason provided), I know of no logs and the event log has no information either. Questions: What are the best drivers to use? How do we actually install them? How can we then set up teaming and how do we set up the VLAN behavior wanted?

  Read the article

• Can't pop3 from exchange server after a reboot

  - by BLAKE

  Last night I shutdown my Exchange 2003 Virtual Machine, I added a new VHD (For backups), and booted it again. Now I can't POP3 email from it with Outlook 2007. In Outlook I get the error: Task '[email protected] - Receiving' reported error (0x800CCC0F) : 'The connection to the server was interrupted. If this problem continues, contact your server administrator or Internet service provider (ISP).' Does anybody know what is wrong? All I did was a reboot. I haven't formated the added disk. There are no weird errors in the event log. I can still send mail with Outlook over port 25. I can send and recieve mail with OWA. I can POP3 the mail to my phone (it take about 15 minutes after sending a message, but I do get it eventually). EDIT: The 'Microsoft Exchange POP3' Service says that it is started but if I stop it and try to start it again, it fails saying 'Could not start the Microsoft Exchange POP3 service on Local Computer. Error 1053: The service did not respond to the start or control request in a timely fashion.' I did some googling and someone on exchangefreaks.com said that if I use task manager to 'End Task' on inetinfo.exe, then I can start the POP3 service fine. Does anyone know what causes this problem? I am fine for now since I did get the Service started, but If it does this after every reboot...

  Read the article

• Mac OS X Client With Static DHCP Assignment Requests Wrong IP via Option 50

  - by Starchy

  I have a number of Mac (and a few Linux) laptops getting DHCP from a Force10 layer 3 switch, the only DHCP server on the subnet. There's a global dynamic pool, and for each full-time employee's laptop I have a single IP static pool set by MAC address. One and only one of the clients, running OS X 10.7.5, consistently fails to get a static assignment. The MAC address in the static pool definition has been carefully re-checked. Running tcpdump on a mirrored port when the laptop connects, I see that it is specifically requesting 10.100.0.252 (a dynamic address): 11:32:10.108280 IP (tos 0x0, ttl 255, id 28293, offset 0, flags [none], proto UDP (17), length 328) 0.0.0.0.bootpc > broadcasthost.bootps: [udp sum ok] BOOTP/DHCP, Request from 3c:07:54:xx:xx:xx (oui Unknown), length 300, xid 0x1399da89, Flags [none] (0x0000) Client-Ethernet-Address 3c:07:54:xx:xx:xx (oui Unknown) Vendor-rfc1048 Extensions Magic Cookie 0x63825363 DHCP-Message Option 53, length 1: Request Parameter-Request Option 55, length 9: Subnet-Mask, Default-Gateway, Domain-Name-Server, Domain-Name Option 119, LDAP, Option 252, Netbios-Name-Server Netbios-Node MSZ Option 57, length 2: 1500 Client-ID Option 61, length 7: ether 3c:07:54:xx:xx:xx Requested-IP Option 50, length 4: 10.100.0.252 Lease-Time Option 51, length 4: 7776000 Hostname Option 12, length 10: "host-name" END Option 255, length 0 PAD Option 0, length 0, occurs 8 I haven't been able to find any extra system prefs or unusual software on the laptop. Disabling the interface and rebooting or temporarily setting the IP manually both fail to make any difference. Any suggestions appreciated.

  Read the article

• Possible DNS issue?

  - by durilai

  I am having an issue, which I think stems from DNS. I have 2 servers. Server 1 is AD server with DNS, which was automatically configured when installing AD. The second server is a web server that is part of the domain, but it is not AD nor any other role. I can remote desktop in from server 1 using internal IP address, but when I attempt to connect from any other computer it fails, the computer can connect to server 1. I am able to ping both servers, as well as nslookup both using their FQDN. I am also able to telnet to port 3389. Any help is appreciated UPDATE I do not think it is DNS anymore, but not sure what it is. The remote desktop connects and I get to the login prompt, but when I start to enter credentials it disconnects. I then am unable to reconnect. If I wait for about 10 minutes it will allow me to repeat, but with the same results. UGH!!!

  Read the article

• Network config for KVM on physical machine with single NIC and single public IP

  - by neo0

  I have a physical machine running CentOS 6.4 and I will rent a place to run it in a data center. I want to install KVM on that machine to run some virtual machines. The problem is my physical machine have only one NIC and the data center give me a public IP for that interface. So how should I configure network on the physical machine to make it assign for each vm a private IP that can connect to Internet. If I create a br0 bridged with eth0 interface and create a vm with option --bridge=br0 then KVM could not assign an IP for the vm so setup can not be done. Should I use NAT mode? Does KVM have any host-only network like Virtualbox? But the vm still has to connect to outside? Thank you! Update I install the guest network using NAT (--network network:default) and then I only have to port-forwarding from the host. But if I config br0 bridged with physical eth0 then the guest can not get an IP from boot. So I removed the br0 and it worked.

  Read the article

< Previous Page | 547 548 549 550 551 552 553 554 555 556 557 558  | Next Page >