Search Results

Search found 16340 results on 654 pages for 'screen projection'.

Page 551/654 | < Previous Page | 547 548 549 550 551 552 553 554 555 556 557 558  | Next Page >

• CentOS 5.5 remote kickstart installation stalls at "Starting install process." How to debug?

  - by ewwhite

  Hello, I'm having a difficult time with a remote CentOS 5.5 kickstart installation on an HP ProLiant DL360 G6. This is in an environment where I maintain an internal CentOS yum repository. The kickstart installation and post scripts have been tested and normally work. This hardware is also common in this environment, so I do not believe that it is a factor. Unfortunately, I'm having problems with a specific server install. The system is remote to the yum repository at a distance of 500 miles. They are connected over a private low-latency 100-megabit layer 2 connection (26ms round-trip). I'm mounting the 10mb CentOS 5 netinstall ISO image via an HP ILO remote console. The initial boot parameters are: linux ks=http://yum.abctrading.com/prop.cfg ksdevice=eth0 ip=x.x.x.x dns=x.x.x.x netmask=255.255.255.0 gateway=x.x.x.x I'm using the url --url http://ks.abctrading.com/5.5/os/x86_64/ method of installation. This quickly boots into the anaconda installer, pulls the kickstart config and formats the drives. The process eventually halts at the screen below, reading "Starting install process.". Going to the other virtual consoles give the second image below. The process stalls at this point and cannot proceed with the rest of the installation. Running the same kickstart config locally works just fine. I've tried mounting the boot ISO from the console as well as from the ILO2 command line pointing to a locally-hosted boot ISO via http. How can I debug this? Are there any options I've overlooked?

  Read the article

• How do I use a Minitel terminal as a linux dumb terminal

  - by Pawz

  I recently purchased a US version of the Alcatel Minitel terminal. I think it's a 1B version. Pictures of it here: I tried connecting a null modem to the 25 pin port on the back and plugging it into a linux box running agetty but I couldn't get it to show any signs of being connected. I used Google Translate to translate this document into English: http://mirabellug.org/wikini/upload/Documentations_minitel.pdf As far as I can tell, you take it out of videotex mode by typing Fcnt-T A, then turn off local echo with Fcnt-T E, then set it to 4800 baud with Fcnt-P 4. I presume Fcnt refers to the "CTRL" key on my terminal. But I think I'm doing something wrong, because it doesn't look like it's recognising the keystrokes, because "Fcnt-T A" just prints the letter A to the screen, which is not what you'd expect a function key combo to do. Has anyone used these minitel terminals as a linux terminal, and if so, please can you share how to configure the minitel to run as a terminal ? Is the 25 pin plug even the correct port to use ? I read something online that indicated you're supposed to use the 5 pin DIN plug instead, is that right ? If so, what's the 25 pin plug for ? If I am supposed to use the DIN plug, does anyone know the pinouts so I can make a cable ?

  Read the article

• Media Center setup won't complete for watching TV

  - by Robert

  I have a problem watching TV in Media Center. The TV constantly pauses 1/2 second then plays 1 second, pauses 1/2 second, plays 1 second - it is constant and does not vary. This problem occurs on all channels, live or recorded. The bottom 5th of the screen is solid green. I know the problem is Media Center because I can use Pinnacle's TVCenterPro to watch TV and there is no skipping/pausing (and not green on bottom). I was using cable, and switched to DirecTV (satellite). Trying to do "Set up TV signal" in Media Center seems to be what broke it. I get an error "IR Hardware not detected." I can use the remote to "try again" - so the IR hardware works fine (Media Center's remote/sensor). I tried plugging the IR Blaster into both ports, and I tried a different USB port for the IR receiver. I can't complete the setup. Media Center was playing TV okay (with the new DirecTV) before I tried to run setup. (I ran setup to try to do recording with Media Center.) Hardware/Software: Pinnacle PCTV 800i HD PCI card (coax cable from DirecTV tuner), ATI Radeon HD 3200 Graphics, Windows XP SP3 Media Center Edition, AMD Athlon Dual Core 2.5 GHz, 1.75 GB RAM.

  Read the article

• Authenticate VNC session with ConsolKit?

  - by lori

  I have a linux machine running Fedora 16 in a cupboard. It has no screen or keyboard. I connect to it using a combination of vnc and ssh. Recently, after an update, I have had issues with authentication on the machine. If I vnc to it, the kde desktop pops up an error dialog every few minutes saying Authorization failed. Failed to obtain authentication. If I plug in a USB drive it fails to mount, Dolphin reports an authentication issue again. I have had limited success finding the solution. AFAICT, it is an issue with ConsoleKit deeming me to be a non-local user so it prevents authentication. This is the output from ck-list-sessions: $ ck-list-sessions Session5: unix-user = '1000' realname = 'steve' seat = 'Seat6' session-type = '' active = FALSE x11-display = ':1' x11-display-device = '' display-device = '' remote-host-name = '' is-local = FALSE on-since = '2012-09-16T08:07:03.137011Z' login-session-id = '1' I have tried to update my .vnc/xstartup script to include ck-launch-session as follows: $ cat ~/.vnc/xstartup #!/bin/sh exec ck-launch-session vncconfig -iconic & unset SESSION_MANAGER unset DBUS_SESSION_BUS_ADDRESS export XKL_XMODMAP_DISABLE=1 OS=`uname -s` if [ $OS = 'Linux' ]; then case "$WINDOWMANAGER" in *gnome*) if [ -e /etc/SuSE-release ]; then PATH=$PATH:/opt/gnome/bin export PATH fi ;; esac fi if [ -x /etc/X11/xinit/xinitrc ]; then exec ck-launch-session /etc/X11/xinit/xinitrc fi if [ -f /etc/X11/xinit/xinitrc ]; then exec ck-launch-session sh /etc/X11/xinit/xinitrc fi [ -r $HOME/.Xresources ] && xrdb $HOME/.Xresources exec ck-launch-session xsetroot -solid grey exec ck-launch-session xterm -geometry 80x24+10+10 -ls -title "$VNCDESKTOP Desktop" & exec ck-launch-session twm & This has not helped. How can I either authenticate myself to ConsoleKit, or trick it into believing I am a local user?

  Read the article

• Free/opensource application for charting stock prices?

  - by Homunculus Reticulli

  I am looking for a free or FOSS software application for SIMPLY charting stock prices. I am not interested in any of the other nonsense typically bundled with such packages (technical analysis, back testing, tracking etc, etc). All I want to do is the following: Import file from CSV and plot on the chart Ability to scroll the chart left/right (zoom feature would be nice to) Ability to draw straight line (between 2 points) on the plot Ability to plot the graph for different resolutions (for e.g weekly, monthly - or some other custom resolution that I want) print the displayed graph (I can always use screen capture if printing is too much to ask) Thats all I want to do. I am not interested in anything else. I would have thought I could have found something by now. I would have written my own tool (I still will do that at a later stage), but I am a bit short of time at the moment, so I just want something that will do all of the above. Can anyone recommend a package. Last but not the least, I am running on Linux (and would prefer to do so - BUT if I have to, I can run on ahem - you know, Windows)

  Read the article

• Performance experiences for running Windows 7 on a Thin-Client?

  - by Peter Bernier

  Has anyone else tried installing Windows 7 on thin-client hardware? I'd be very interested to hear about other people's experiences and what sort of hardware tweaks they had to do to get it to work. (Yes, I realize this is completely unsupported.. half the fun of playing with machines and beta/RC versions is trying out unsupported scenarios. :) ) I managed to get Windows 7 installed on a modified Wyse 9450 Thin-Client and while the performance isn't great, it is usable, particularly as an RDP workstation. Before installing 7, I added another 256Mb of ram (512 total), a 60G laptop hard-drive and a PCI videocard to the 9450 (this was in order to increase the supported screen resolution). I basically did this in order to see whether or not it was possible to get 7 installed on such minimal hardware, and see what the performance would be. For a 550Mhz processor, I was reasonably impressed. I've been using the machine for RDP for the last couple of days and it actually seems slightly snappier than the default Windows XP embedded install (although this is more likely the result of the extra hardware). I'll be running some more tests later on as I'm curious to see particularl whether the streaming video performance will improve. I'd love to hear about anyone's experiences getting 7 to work on extremely low-powered hardware. Particularly any sort of tweaks that you've discovered in order to increase performance..

  Read the article

• Xorg input devices fail without udev

  - by Sampo

  What I am trying to do: Launch Xorg server without udev device manager. What I have tried to do: Make sure that /dev/ has all required nodes, such as /dev/input/*. Make sure that all required kernel modules are loaded. Launch Xorg. What happens: Xorg starts up as excepted. Xorg loads correct GPU driver and sets right screen resolution. Xorg blocks all input devices (keyboard, mouse), Alt+F[1-12] does not work (can't go back to tty1). Unraw'ing keyboard to take its control from X removes blocking and after unraw I can Alt+F1 back to tty1. Xorg still does not handle any input. Why I think that it should work: Same configuration works well if udev is loaded. Loading udev does not add or modify /dev/ contents, all nodes stays same. My main question is: How to make Xorg input devices work without udev? Any additional information about how Xorg really uses/detects/grabs keyboard would be helpful. And any additional information about what udev really does (other than populating /dev/) would also be helpful.

  Read the article

• Dell XPS 15 L502X hard drive Partition

  - by Mohan Gajula

  I have a situation here. I got my new Dell XPS 15 Laptop. The configuration of hard drive is as below : Volume 1: (OEM Partition): 133MB Volume 2: OS (C:): 685.25 GB Volume 3: Recovery : 13.25 GB Now, I am trying to re-partition my C Drive to have a C: drive with 100 GB and a new drive with 585 GB. Earlier, I tried using the Windows 7 Disk Management to shrink and extend the volume. That lead to the OS and hard drive not working. Dell Tech support tried to fix the issue, but they were not able to fix the issue online. Later a Dell Technician arrived my place, and replaced the hard drive with a new hard drive. Please help me re-partition the C: Drive with 100 GB, and new D drive with 585 GB. I don't want to lose my Recovery Partition. SOLUTION As Suggested by KCotreau below , I have done exactly. I have resized the C drive to 100 GB. And then applied the changes. Windows got restarted. On the boot screen, the partition was taking place. It took around 30 mins ( approx. ). Once after restart, I can see my C drive is 100 GB. Now opened the Easeus again. And created a new partition for the free space ( 585 GB ) this took 10 seconds to create. Here goes the screenshot after partitioning. Thanks to KCotreau. You are amazing.

  Read the article

• iptables, blocking large numbers of IP Addresses

  - by Twirrim

  I'm looking to block IP addresses in a relatively automated fashion if they look to be 'screen scraping' content from websites that we host. In the past this was achieved by some ingenious perl scripts and OpenBSD's pf. pf is great in that you can provide it nice tables of IP addresses and it will efficiently handle blocking based on them. However for various reasons (before my time) they made the decision to switch to CentOS. iptables doesn't natively provide the ability to block large numbers of addresses (I'm told it wasn't unusual to be blocking 5000+), and I'm a bit cautious over adding that many rules into an iptable. ipt_recent would be awesome for doing this, plus it provides a lot of flexibility for just severely slowing down access, but there is a bug in the CentOS kernel that is stopping me from using it (reported, but awaiting fix). Using ipset would entail compiling a more up-to-date version of iptables than comes with CentOS which whilst I'm perfectly capable of doing it, I'd rather not do from a patching, security and consistency perspective. Other than those two it looks like nfblock is a reasonable alternative. Is anyone aware of other ways of achieving this? Are my concerns about several thousand IP addresses in iptables as individual rules unfounded?

  Read the article

• Keyboard's media keys are blocked by a program

  - by Mike Hanson

  I've got a Microsoft Natural Ergonomic Keyboard 4000. In addition to the regular keys, it's also got keys for Web/Home, Search, Mail, Favorites (5), Calculator, and Media functions (Mute, Volume Up/Down, and Play/Pause). Everything works most of the time, and the exception is rather odd. I use a programming system called Clarion. When that has focus, the Media keys don't work. (All the others still do.) I've also discovered that programs that I create using Clarion also block the media keys (only when they have focus). This indicates that it's probably something in Clarion's Run-Time Library (RTL) that's causing the trouble. The keys will work if I click on a non-Clarion window before hitting the media key, but that's an undesirable hassle. The odd thing is that I have many colleagues with the same keyboard, and they have no problem. When I recently upgraded from Vista Professional to Win7 Ultimate, I noticed that various things "appear" differently. For example, with my old system, when I changed the volume or muted the volume bar visualization always appeared at the bottom right on the screen. Now it doesn't appear in certain programs, even when it works. This indicates an order of precedence for visual elements. I'm fairly certain a similar order of precedence exists for keyboard hooks. Depending on how the hooks are defined, and the order in which they're applied, it would seem that sometimes the IntelliType drivers don't see the media keystrokes. The Media keys probably behave differently than the rest of the "special" keys, because they are more of a standard across all keyboards, so perhaps are handled by a different driver hooking mechanism. Does anyone have any suggestions of how I might fix this problem? Is there some way to change the order of hooks? Delay the loading of the IntelliType driver? Thanks in advance!

  Read the article

• Windows 8 Doesn't Shutdown Properly With Fast Start-Up Enabled

  - by Patrick

  While Fast start-up is enabled, on turning the computer off (shutdown) the computer idles for about 5min after logging out/screen turning off. It then turns off. On returning into Windows I receive the error message saying Windows didn't shut down properly. Hibernate works fine, and I am told this shouldn't be the case - If one doesn't work, neither should. It works when both Fast start-up is enabled and disabled, as does restart and sleep. Windows is installed under UEFI. The UEFI ultra fast boot option for my motherboard cannot be enabled as my GPU doesn't support some UEFI GOP tech. As far as I know, not related to windows fast start-up, but thought it was worth mentioning. To clarify, if this: http://www.eightforums.com/tutorials/6320-fast-startup-turn-off-windows-8-a.html is enabled, the computer does not shut down properly. EDIT: Some more information on the matter: Formatting didn't fix the issue. Still fails regardless of drivers installed. Hardware was purchased ~6months ago. Running a good SSD. Event viewer Always these two messages in close succession: Error (event ID 6008): The previous system shutdown at 7:45:21 PM on ?27/?10/?2012 was unexpected. Critical (kernel power, event ID 41): The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly. Upon installing WPT as suggested below to figure out what was happening during shutdown, and running the cmd xbootmgr -trace shutdown -noPrepReboot -traceFlags BASE+CSWITCH+DRIVERS+POWER -resultPath C:\TEMP Windows fast start-up is now working consistently. Still works upon uninstalling WPT. This is the only change to occur on the computer. Nothing else has bee installed/uninstalled, no Windows Updates, nothing. Windows fast start-up did not work prior to installing WPT and running the cmd (made sure I tested).

  Read the article

• Gvim on Windows 7: ALT codes not working

  - by John Sonderson

  I would like to be able to enter ALT codes in Gvim on Windows 7 as documented on the following site: Alt Codes On Windows (Windows 7 in my case), to generate a character via an ALT code you make sure that the NumLock key on your keypad is toggled on, hold down the ALT key, enter the keycode on the numeric keypad, and then release the ALT key. However this does not work in Gvim on Windows (which ignores the fact that I am pressing the ALT key and just prints to entered keypad key directly onto the screen). How can I get these keystroke combinations to work in Gvim as well? Thanks. EDIT: As the answer below points out, the way to insert non-ASCII characters for which you do not have entries on your keyboard without changing the keyboard layout is as follows: Make sure you are in insert mode, and then type CTRL-V followed by the Unicode character code of interest, for instance: CTRL-V u00E0 (generates à) CTRL-V u00C8 (generates È) CTRL-V u00E8 (generates è) CTRL-V u00E9 (generates é) CTRL-V u00EC (generates ì) CTRL-V u00F2 (generates ò) etc... See for instance http://unicode-table.com/ for a full list of Unicode character codes. The following list of Unicode characters by language may also be useful: http://en.wikipedia.org/wiki/List_of_Unicode_characters In some cases such as this one, though, there might be an easier way to enter special characters (see :help digraphs and :digraphs). For example, while in insert mode you may be able to type the following: CTRL-K E! (yields É) CTRL-K a' (yields á) Note that as the following page shows: http://code.google.com/p/vim/source/browse/runtime/doc/digraph.txt Gvim 7.4 contains an even wider set of default digraphs than Gvim 7.3, thus providing convenience to an even broader set of languages. Regards.

  Read the article

• No video signal and server shuts down

  - by Ilya

  I have a brand new server. The motherboard is Intel S2600CP4, two 8-core Intel E5-2600 processors. RAM is 8 DIMM slots of 8 GB each (KVR1600D3D4R11SK4/32GI, I installed them into the blue slots), Power supply is 1050W Corsair. Most of the time the server won't start up - the fans are spinning, but I don't have video signal. And it keeps restarting on its own every 3 mins. But maybe after 30 mins it will eventually load and show something on the screen. I even was able to install ESXi 5.0 (vSphere) on it. It recognizes both CPUs and all of the 64GB of RAM. But even then it worked only for around 5 hours and then restarted on its own. What's the problem? That's a very expensive peace of hardware and I can't afford purchasing a new motherboard/CPU. By the way, on the front panel the "System Status" LED is constantly amber (not blinking), even when the server started successfully. And also in the BIOS I can see lots of "processor 01 unable to apply microcode update 8160" fatal errors. Please help me with issue, I will really appreciate this!

  Read the article

• Alternative software for Pinnacle PCTV 100e

  - by Stijn Sanders

  I have a Pinnacle PCTV 100e external USB cable television receiver. I've been using Pinnacle's software that came with the card (TVCenter Pro) to record things at given times. Things I don't like is an extremely high CPU load, and that it doesn't seem to halt the screensaver from running when watching in full screen. Also, I was away the last two weeks, and the schedules went terribly bust. Some items were recorded hours before or after the actual scheduled time (and now I missed some shows), and some recurring schedules weren't converted into the next occurrence correctly! Is there good alternative software that would work with my PCTV 100e? (Preferalby cheap or free) I've tried VLC Player, which gets video, but no audio. I've tried MediaPortal, which crashes when trying to scan for channels. When I select a channel manually, the stored mpg has big errors in encoding and is also missing audio. There's VirtualDub, but that doesn't have ready-made scheduled-recording options. This I can conjure some scheduled scripts for, but I've noticed the sync gets awfully wrong after some time. I've tried Windows Media Center, but it doesn't seem to support the PCTV 100e.

  Read the article

• Troubleshooting a Windows 7 PC that wouldn't sleep

  - by NPE

  I have a new Windows 7 PC that wouldn't sleep (not just automatically, but also when specifically told to). The screen goes black momentarily, but within two seconds the machine comes back as if nothing has happened. I tried powercfg energy. This produces some errors quoted at the bottom of this post, plus some warnings about timer resolution. There are no USB devices connected other than wireless keyboard + mouse (Logitech MK250); I tried unplugging them to no effect. The motherboard is Asus P7P55D-E. powercfg lastwake says "Wake History Count - 0", which I take to mean that it never actually went to sleep. I dual boot into Ubuntu, and was having exactly the same problem on the Linux side. That turned out to do with USB 3.0, which I've now disabled in the BIOS. This has solved the problem on the Ubuntu side of things, but made no difference to Windows 7. Any suggestions? Suspend:USB Device not Entering Suspend The USB device did not enter the Suspend state. Processor power management may be prevented if a USB device does not enter the Suspend state when not in use. Device Name Generic USB Hub Host Controller ID PCI\VEN_8086&DEV_3B34 Host Controller Location PCI bus 0, device 29, function 0 Device ID USB\VID_8087&PID_0020 Port Path 1 USB Suspend:USB Device not Entering Suspend The USB device did not enter the Suspend state. Processor power management may be prevented if a USB device does not enter the Suspend state when not in use. Device Name USB Root Hub Host Controller ID PCI\VEN_8086&DEV_3B34 Host Controller Location PCI bus 0, device 29, function 0 Device ID USB\VID_8086&PID_3B34 Port Path USB Suspend:USB Device not Entering Suspend The USB device did not enter the Suspend state. Processor power management may be prevented if a USB device does not enter the Suspend state when not in use. Device Name USB Composite Device Host Controller ID PCI\VEN_8086&DEV_3B34 Host Controller Location PCI bus 0, device 29, function 0 Device ID USB\VID_046D&PID_C52E Port Path 1,8

  Read the article

• Explorer.exe keeps crashing during log in

  - by asif

  I have got a weird problem. My windows 7 has two user accounts (both are administrator). I can log in to one account and do all sort of work. But whenever I try to log in to other account, it shows a blank screen and a messagebox pops up with "windows explorer has stopped working". The options available are: Close the program Check online for a solution and close the program The problem signature is as follows: Problem Event Name: InPageError Error Status Code: c000009c Faulting Media Type: 00000003 OS Version: 6.1.7601.2.1.0.256.1 Locale ID: 1033 Additional Information 1: 0a9e Additional Information 2: 0a9e372d3b4ad19135b953a78882e789 Additional Information 3: 0a9e Additional Information 4: 0a9e372d3b4ad19135b953a78882e789 If I press alt+ctrl+del and then select start task manager, it also crashes. I can not run any program using runas command (from good profile) too. The task manager and runas programs all show same problem signature. I read the similar question and followed all the steps, but no luck. Later, I viewed the event log and found that, explorer.exe could not access a file. I checked the location but the file is there. The actual message is: Windows cannot access the file C:\Users\testuser\AppData\Local\Microsoft\Windows\Caches\{AFBF9F1A-8EE8-4C77-AF34-C647E37CA0D9}.1.ver0x0000000000000020.db for one of the following reasons: there is a problem with the network connection, the disk that the file is stored on, or the storage drivers installed on this computer; or the disk is missing. Windows closed the program Windows Explorer because of this error. The question is, how can I resolve this issue? Should I just delete the file or replace it with another one to stop explorer.exe from crashing? offtopic: What is the content of this file and why it is necessary?

  Read the article

• Video output vanishes and it isn't the video card... suggestions?

  - by Ira Baxter

  I have a high-end dual processor Dell workstation that operated for several years without problem. Recently, the video output has gone flaky, in the sense that after 2-3 days, it loses synch with the monitor (sometimes you can still see a hashed-mess of the what you expect to see on the screen). Poking at the keyboard, and accessing the file system on the machine from over the network, indicates that the machine is running fine and its just the video. A reboot fixes the problem... for another day or two. This in effect makes the machine unusable. So, I replaced the video card with an exact duplicate bought from e-bay. (I checked after the dupe arrived to be sure, yep, same model number). I still get the same behavior. So unless I believe that both video cards are broken the same way, I have to beleive this is a problem with the motherboard/power supply, neither of which I am inclined to replace. The only other possibility I can think of is a Windows update to the graphics driver. How would I check for this? Anybody had a similar problem? Otherwise we're junking what used to be a perfectly good machine. (Another couple of hours of more wasted effort and that's it in terms of economics anyway).

  Read the article

• How do I restrict the Open/Save dialog in Windows to one folder?

  - by MindModel

  I spend a significant amount of time helping non-techies use their PC's. I realized most of that time is spent trying to explain to them how the Windows folder hierarchy works, where the "open file" dialog is pointing now, and how to find that Word document they saved. All this time, they're telling me they "just want to print the file". They refuse to learn how to read the PC screen, try to memorize a fixed set of steps, and end up calling me back to tell me their files disappeared again. I realize it's not productive to try to restrict where PC apps (e.g. Quicken) store files. But if there was a Windows utility I could turn on or off that would restrict the Open/Save dialogs in Windows apps, my noob user friends and I would save an enormous amount of time. The goal would be to have all files whose locations are chosen by the Save dialog saved to one folder, and have the Open dialog always point to that folder, until the utility is turned off. Does such a Windows utility exist?

  Read the article

• GA 8KNXP Rev1.0: 4 GB installed, only 3.5 GB recognized by BIOS

  - by hurikhan77

  I've installed 2x 1 GB and 4x 512 MB memory into my GA-8KNXP system which would sum up to 4 GB. The specification from the manual says: Maximum memory support: 4 GB. If all six slots are utilized, slot 5+6 may only equipped with single-sided RAM modules. And so I did. Anyway: The BIOS counts up to 3.5 GB and finishes there. Also my Linux system reports only 3.5 GB of memory although 4 GB memory support is activated in the kernel. So I suppose this is a memory mapping issue or a hardware issue. I've tried removing only on of the 512 MB memory modules leaving 5 modules in place. But that just stopped the system from powering on correctly (screen stays black although fans and leds come to live). Dual Channel was detected and enabled so the system technically found all 6 modules. "dmidecode" in Linux reports only memory in slots 1 to 4 and ignores slots 5+6, so it only detects 3 GB of memory. It also says the system would support up to 16 GB of memory with 4 GB modules per slot. I think technically the chipset should be able to offer and utilize the complete 4 GB memory range. Any clues what else I could check? Or do I have just to live with 0.5 GB wasted memory?

  Read the article

• Write Fedora.iso to USB and boot it from a Macbook

  - by MTilsted

  I have an .iso image of the full Fedora 16 install (Downloaded from http://fedoraproject.org/en/get-fedora-options#formats as "Fedora 16 DVD") and the question now is: How do I write it on a USB stick, so I can install it on my Mac book? I tried using DD as the install guide said, and that gave me a USB stick which can boot from my PC. But it can't boot from the Mac (The Mac start menu don't show it as a boot option). Edit: I downloaded a live install image, and did this (SSD is my USB 4GB thing) /sbin/mkdosfs -F 32 -n usbdisk /dev/dev/sdd1 sudo livecd-iso-to-disk --format --reset-mbr --efi /tmp/download/Fedora-16-i686-Live-KDE.iso /dev/sdd1 And this produced an image which can boot on my pc but not on my mac. This seems to indicate that the --efi is not working, because if it really was EFI it would not boot on a normal pc, would it? I then tried this: (Difference being that I write the image directory to /dev/sdd instead of /dev/sdd1) but this still will not boot on the Mac (it newer shows up at the startup screen on the Mac). sudo livecd-iso-to-disk --format --reset-mbr --efi /tmp/download/Fedora- PS: My host Linux is Fedora 13.

  Read the article

• During Vista Repair - No operating system is listed.

  - by Jack Marchetti

  After a Windows update, my brother's Gateway computer loads to the "Step 3 of 3: 0%" and reboots. Safe Mode does not work. I placed a Vista DVD in the drive, and re-booted. (Note, this is my Vista DVD, not the Recovery/System disc that would come with a computer. Gateway does not give you CD's anymore. I believe they store recovery on a partition, but that partition has been wiped out). I chose "Repair Your Computer" I get a dialog box, but no operating system is listed. I'm then prompted to "Load Drivers". What drivers am I supposed to be loading here and where from? I placed a CD in the drive to "load drivers" but I don't see my DVD drive listed. All I saw where X:/Sources along with several Removable Media slots that were empty. On another screen I tried Startup Repair, which didn't do anything. I attempted to use System Restore - but it doesn't detect the hard drive. I'm guessing that I'm missing some sort of SATA driver and that is why the hard disk is not being found. Any ideas on this?

  Read the article

• Apple / Mac OS X - Is there a Package Manager like Linux

  - by Walter White

  I am a Linux/UNIX user and love the package management that comes with it. For the most part, I like Ubuntu, but just like anything else, it is the minor things that you live with daily that would be nice if they just worked. My main issue is my wacom tablet while it works, every time there is an OS update, I have to rebuild the wacom driver. The other slightly annoying issue is, my ATI video card is not fully supported. When I use the HDMI out, the sound doesn't go through it, and the screen is not entirely used. I would happily get an Apple if it had a similar package management system like Ubuntu, Gentoo, or other Linux distribution. This takes the work out of getting the latest enhancements or fixes. It also takes all the guess work out about what you need to get something to work. I just want to use my computer, not administer it. Aside from Apple applications, if I wanted to install the GIMP on an apple, would it go and fetch ufraw if I wanted support for that and whatever other dependencies GIMP has? If I want Netbeans installed, will it go and get a JDK and maven if I want that? If not, is there something in the works? I know I don't update my applications that frequently, but that is mainly because I'm not aware of the updates. The updates all happen in the background. Walter

  Read the article

• How to fix a bootable USB Kubuntu installation when the drive has maxed out?

  - by NoCatharsis

  I used Universal-USB-Installer-v1.5.1 from PenDriveLinux.com with Kubuntu 10.04 so I could set up my 4GB flash drive as a totally independent installation. Unfortunately, there was an OS upgrade available which Kubuntu downloaded and attempted to install. This, along with some other software, apparently maxed out my drive before I realized it. Now when I try to boot from the drive, everything boots as normal to the OS boot screen where I select "Boot from this Kubuntu USB Installation." The startup process initiates, then stalls about halfway through and hangs indefinitely. I'm guessing the drive is trying to use space it doesn't have and completely stops working. I realize that once the OS upgrade is in place, the old files could be deleted for a potential 700MB space gain. However, I just have no way to get into the OS and complete the upgrade. My main OS is Windows 7. Is there a way I can fix this issue from within Windows without formatting the entire drive and reinstalling Kubuntu from scratch?

  Read the article

• Windows XP only loads in VGA mode, and crashes when raising resolution

  - by Harel

  My kid's computer (Windows XP, SP3) started to (what appears to be) crash on boot. It will only boot in Safe or VGA mode, and if I try to raise the resolution from 640x480 it just reboots itself, and a error appears in the Event Log. When it loads up not in VGA mode, the monitor shuts off just after the windows logo is shown. It seems like windows is actually running but I can't see anything on screen (monitor is off for lack of signal). Nothing was installed recently that I know of, short of the usual windows updates. Thanks, Harel Below is the event log error: Event Type: Error Event Source: System Error Event Category: (102) Event ID: 1003 Date: 15/04/2012 Time: 16:27:11 User: N/A Computer: ----- Description: Error code 1000008e, parameter1 c0000005, parameter2 f745b0bf, parameter3 ede24f98, parameter4 00000000. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: 53 79 73 74 65 6d 20 45 System E 0008: 72 72 6f 72 20 20 45 72 rror Er 0010: 72 6f 72 20 63 6f 64 65 ror code 0018: 20 31 30 30 30 30 30 38 1000008 0020: 65 20 20 50 61 72 61 6d e Param 0028: 65 74 65 72 73 20 63 30 eters c0 0030: 30 30 30 30 30 35 2c 20 000005, 0038: 66 37 34 35 62 30 62 66 f745b0bf 0040: 2c 20 65 64 65 32 34 66 , ede24f 0048: 39 38 2c 20 30 30 30 30 98, 0000 0050: 30 30 30 30 0000

  Read the article

• Windows XP Boot Issue - Diagnosing A Hard Drive Failure

  - by duffymo

  My five-year-old HP desktop running Windows XP SP3 wouldn't boot from the hard drive yesterday afternoon. I would see the boot sequence begin, then nothing but a black screen. Fortunately, I had just done an Acronis backup to my external drive in the morning, and I have a bootable USB key. I put the USB key into the drive, powered up the machine, and put the USB key first in line in the boot sequence. Voila! My machine came alive. But now I'm confused as to what the problem is and what to do next. I assumed that my hard drive was toast. But now that the machine is alive I can see files on my C: drive that have changes I made just yesterday. Clearly the drive is not dead. Here are my questions: What could explain my inability to boot from the hard drive? What would a remedy be? What's my best course of action? Should I replace the hard drive with a new one? If I replace the hard drive, do I reinstall the OS and apply the backup I did yesterday? If I decide that re-installing Windows XP makes no sense, how do I get back the Acronis backup that I did yesterday? I don't want to lose that. UPDATE: I just learned one more key fact. I'm having some work done on my house. I neglected to shut my machine down before the contractor came. My wife said he shut down the power to do some work on a circuit and then powered the house back up. I have a surge protector, but is it possible that cycling the power did some damage?

  Read the article

< Previous Page | 547 548 549 550 551 552 553 554 555 556 557 558  | Next Page >