Search Results

Search found 17949 results on 718 pages for 'job title'.

Page 552/718 | < Previous Page | 548 549 550 551 552 553 554 555 556 557 558 559  | Next Page >

• sorry, the maximum allowed clients from your host (10) are already connected" FTP error

  - by Sejanus

  Hello, I keep getting the "sorry, the maximum allowed clients from your host (10) are already connected" error whenever I try to transfer a large number of files. At first I thought it's a filezilla bug, however I get the same error basically with every FTP client I've tried, including Total Commander under Wine. I do not get that error using Windows. I did try to limit maximum allowed connections for Filezilla, both in server settings and in global settings, it didnt change anything. I did try to switch between passive and active modes (not sure if it's related at all, just last desperate attempt), and it didnt change anything either. When I try to use native ftp client (not sure how is it called, the one in Places - Connect to a server) I get abstract "connection refused" error every time I transfer large number of files. Connection is refused for separate particular files, if I click "Ignore" each time the rest of files are transfered perfectly well, so I assume it's the very same error. Anything I could do? This really drives me mad, transfering large numbers of files is a part of my everyday job... P.S. and this happens with many different FTP servers. Also I dont get this error in Windows. So I assume it's not a server problem. P.P.S. I am aware of similar question here, the answer provided just didn't solve it to me.

  Read the article

• Can't connect to Sql Server 2008 named instance

  - by eidylon

  I just installed Sql 2008 Express on a new server running Windows Server 2008. I know Sql is working properly, because I can connect to the db fine locally, on the server. I cannot connect to it from a client machine though, neither by IP address nor by machine name (iporname\instance). I know I have the correct IP address, because I am RDCing into the server to perform all this configuration and setup, and if I ping the server name, it is resolving to the correct IP address as well. On the server, I have set up an inbound firewall exception allowing all traffic on any port on any protocol to sqlservr.exe. In SSMS, in server > Properties > Connections Allow remote connections to this server is enabled. In Sql Server Configuration Manager, TCP/IP is enabled in both the Protocols for <instance> and the Client Protocols sections. I looked in the Windows logs, but don't see anything about connections being denied or dropped. As far as I can see, I have everything set right, but cannot connect from a client machine. The client CAN connect to other Sql 2008 Express servers okay, so I know the client configuration is correct. Any ideas where else I can look for info of what/where/how this connection is dropping, greatly apprecaited! The error being returned by the client is: **TITLE: Connect to Server** Cannot connect to [MY.IP.ADD.RSS]\[MYINSTNAME]. ADDITIONAL INFORMATION: A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and SQL Server is configured to allow remote connections. (provider: SQL Network Interfaces, error: 26 Error Locating Server/Instance Specified) (Microsoft SQL Server, Error: -1)

  Read the article

• schedule backup and restore of SSAS 2008 database

  - by Manjot

  Hi, I can backup and restore databases on Microsoft SQL server Analysis Service 2008 using GUI as from Backup SSAS I want to schedule backup and restore it to another server every night. so what i did is : I scripted out the backup and restore process from the GUI. Created a new SQL server agent job in database engine and added a "Run SSAS query" step. Copied the scripts to this step. But it fails. the scripts that the GUI copied out look like: <Backup xmlns="http://schemas.microsoft.com/analysisservices/2003/engine"> <Object> <DatabaseID>DB</DatabaseID> </Object> <File>C:\Backup\DB.abf</File> <AllowOverwrite>true</AllowOverwrite> </Backup> <Restore xmlns="http://schemas.microsoft.com/analysisservices/2003/engine"> <File>\\server\C$\Backup\DB.abf</File> <DatabaseName>DB</DatabaseName> <AllowOverwrite>true</AllowOverwrite> </Restore> Any help please?

  Read the article

• How can a Linux Administrator improve their shell scripting and automation skills?

  - by ewwhite

  In my organization, I work with a group of NOC staff, budding junior engineers and a handful of senior engineers; all with a focus on Linux. One interesting step in the way the company grows talent is that there's a path from the NOC to the senior engineering ranks. Viewing the talent pool as a relative newcomer, I see that there's a split in the skill sets that tends to grow over time... There are engineers who know one or several particular technologies well and are constantly immersed... e.g. MySQL, firewalls, SAN storage, load balancers... There are others who are generalists and can navigate multiple technologies. All learn enough Linux (commands, processes) to do what they need and use on a daily basis. A differentiating factor between some of the staff is how well they embrace scripting, automation and configuration management methodologies. For instance, we have two engineers who do the bulk of Amazon AWS CloudFormation work, and another who handles most of the Puppet infrastructure. Perhaps a quarter of the engineers are adept at BASH shell scripting. Looking at this in the context of the incredibly high demand for DevOps skills in the job market, I'm curious how other organizations foster the development of these skills and grow their internal talent. Scripting doesn't seem like a particularly-teachable concept. How does a sysadmin improve their shell scripting? Is there still a place for engineers who do not/cannot keep up in the DevOps paradigm? Are we simply to assume that some people will be left behind as these technologies evolve? Is that okay?

  Read the article

• Global Address List, Multiple All Address Lists in CN=Address Lists Container

  - by Jonathan

  When my colleges (that was way before my time here) updated Exchange 2000 to 2003 a English All Address Lists appeared in addition to the German variant. The English All Address Lists have German titled GAL below it. This has just been a cosmetic problem for the last few years. Now as we are in the process of rolling out Exchange 2010 this causes some issues. Exchange 2010 picked the wrong i.e. English Address Lists Container to use. In ADSI Editor we see CN=All Address Lists,CN=Address Lists Container,CN=exchange org,CN=Microsoft Exchange,CN=Services,CN=Configuration,DC=domain and CN=Alle Adresslisten,CN=Address Lists Container,CN=exchange org,CN=Microsoft Exchange,CN=Services,CN=Configuration,DC=domain. In the addressBookRoots attribute of CN=Microsoft Exchange,CN=Services,CN=Configuration,DC=domain both address lists were stored as values. We removed the English variant from addressBookRoots and restarted all (old and new) Exchange servers. User with mailboxes on the Exchange 2003 now only sees the German variant. Exchange 2010 is still stuck with the English/Mixed variant as are Users on Exchange 2010. Our goal would be to have Outlook display the German title of All Address Lists and get rid of the wrong Address Lists Container.

  Read the article

• Scheduled task does not run on WIndows 2003 server on VMWare unattened, runs fine otherwise

  - by lnm

  Scheduled task does not run on Windows 2003 server on VMWare. The same setup runs fine on standalone server. Test below explains the problem. We really need to run a more complex bat file, but this shows the issue. I have a bat file that copies a file from server A to server B. I use full path name, no drive mapping. Runs fine on server B from command prompt. I created a task that runs this bat file under a domain id with password that is part of administrator group on both servers. Task runs fine from Scheduled task screen, and as a scheduled task as long as somebody is logged into the server. If nobody is logged in, the task does not run. There is no error message in Task Scheduler log, just an entry that the task started, bit no entry for finish or an error code. To add insult to injury, if the task copies a file in the opposite direction, from server B to server A, it runs fine as a scheduled unattended task. If I copy a file from server B to server B, the task also runs fine unattended, I recreated exactly the same setup on a standalone server. No issues at all. I checked obvious things like the task has "run only as logged in" unchecked, domain id has run as a batch job privilege and logon rights, Task Scheduler service runs as a local system, automatic start. Any suggestions?

  Read the article

• Troubleshooting wireless connection problem / site survey?

  - by johnnyb10

  I just started in the IT department of a small company (200 users) and it's clear that one of the main problems that is driving everyone crazy is the spotty nature of the wireless connectivity throughout the office, particularly in certain conference rooms. This is a huge problem because the connection often drops during important presentations to clients. I was hired to help ease the load on the existing IT admin, who has done a great job, but is overloaded with many other tasks to deal with. So I would like to try to help out with this wireless issue. I am looking for advice on the best way to solve this problem--a realistic troubleshooting methodology that does not require me to spend any money. So far, I've experimented with Ekahau Heat Mapper, which is free and helps create a site survey. But I'm not exactly sure what I'm looking for or if there are other programs/tools/methods I should try as well. Any advice would be greatly appreciated. [Some background: The wireless setup consists of an HP ProCurve Mobility MSM (710?) controller that controls 10 access points throughout the building. There are three virtual wireless networks configured on the controller: one seems to be a default that cannot be changed, one is for internal employees and authenticates via Active Directory, and the third is a guest network for visitors. When I use HeatMapper, these show up as three different SSIDs, with different MAC addresses, all on the same channel. At first I thought maybe this would cause interference, but this seems to be the way the controller works;apparently, it automatically configures the channels to avoid interference from the other APs on the network.]

  Read the article

• SQLVDI error - attempt to release mutex not owned by caller

  - by Chris W

  I've started getting some errors in the App event log of one of our database servers (Windows 2003 & SQL Server 2005). The nightly full database backups are completing successfully however immediately after the job success is written to the event log there is a run of entries that say: SQLVDI: Loc=CVDS. Desc=Release(ClientAliveMutex). ErrorCode=(288)Attempt to release mutex not owned by caller. There's five of these logged - the server itself has more than 20 databases on it which are all backed up successfully. The server is backed up by Bacula using a VSS backup. Has anyone got any ideas what would be causing the errors? They seem to have started after a re-boot on Friday to install some patches which included KB960089. Edit: After getting the errors for a few days they've now stopped without any action on my part other than letting the backups continue as they were. It may be a coincidence but they stopped after Bacula completed its weekly full rather than the daily incremental backup.

  Read the article

• Kickstart installation from USB -- Kickstart location

  - by dooffas

  After managing to get a Fedora ISO to rebuild successfully (for a USB stick) after adding a kickstart file (http://serverfault.com/questions/548405/), I now have an issue with locating the kickstart file on the USB media. When this is done from a CDROM you can simply kickckstart by adding this parameter to boot: linux ks=cdrom This will kickstart (providing the kickstart file is named ks.cfg and is in the root of the disk). Now, obviously this will be different for the USB drive, so from my research, I assumed that this line would do the job: linux ks=hd:sdb1:/ks.cfg Evidently this does not work. I get an error informing me this drive is already mounted and cannot be remounted. EDIT: Actual error message: mount: /dev/sdb1 is already mounted or /run/install/tmpmnt0 busy Warning: Can't get kickstart from /dev/sdb1:/ks.cfg To test that the syntax was correct I placed the kickstart file on another USB stick and loaded the same command to grab ks.cfg from the new location: linux ks=hd:sdc1:/ks.cfg This does work (providing USB sticks are mounted in order, boot - sdb1, kickstart - sdc1). The install will kickstart and complete the install with no issue. Obviously having to use 2 pen drives is somewhat frustrating and unreliable. Is there a way around this?

  Read the article

• Managing Apache to Compensate for WebDAV's Security Masking

  - by Tohuw

  When a user creates a file via WebDAV, the default behavior is that the file is owned by the user and group running the Apache process, with a umask of 022. Unfortunately, this makes it impossible for unprivileged users to write to the files by other means without being a member of the group Apache runs under (which strikes me as a particularly bad idea). My current solution is to set umask 000 in Apache's envvars and remove all world permissions from the webdav parent directory for the user. So, if the WebDAV share is /home/foo/www, then /home/foo/www is owned by www-data:foo with permissions of 770. This keeps other unprivileged users out, more or less, but it's hokey at best and a security disaster awaiting at worst. From my research and poking around at mod_dav and Apache, I cannot find a reasonable solution short of a cron job flipping all the permissions back (I'd rather not have the load and increased complexity on the server). SuExec won't work, either, because WebDAV operations are not going to execute as a different user. Any thoughts on this? Thank you.

  Read the article

• Hostname error on my Slicehost Ubuntu server

  - by allesklar

  Like many folks who upgraded to Rails 2.2, I got an exception raised when sending an email. This version of Rails or later does require using tls for sending emails. The message in the production log file says: hostname was not match with the server certificate I did a whole lot of research and work on this and did everything I could. I changed my slice's hostname to ohlalaweb.com. If I run the command 'hostname' at the CL I get: ohlalaweb.com Postfix seems to work fine. I can send emails from the CL to my gmail, yahoo, and google apps gmail accounts with no problems. Here is the result of cat /etc/postfix/main.cf # See /usr/share/postfix/main.cf.dist for a commented, more complete version # Debian specific: Specifying a file name will cause the first # line of that file to be used as the name. The Debian default # is /etc/mailname. myorigin = /etc/mailname smmtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) biff = no # appending .domain is the MUA's job. append_dot_mydomain = no # Uncomment the next line to generate "delayed mail" warnings #delay_warning_time = 4h readme_directory = no # TLS parameters smtpd_tls_cert_file=/etc/ssl/certs/ohlalaweb.pem smtpd_tls_key_file=/etc/ssl/certs/ohlalaweb.pem smtpd_use_tls=yes # SA created next line to force postfix to use self create certificate smtpd_tls_auth_only=yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache # See /usr/share/doc/postfix/TLS_README.gz in the postfix-doc package for # information on enabling SSL in the smtp client. myhostname = ohlalaweb.com alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases mydestination = localhost.localdomain, localhost relayhost = mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 mailbox_size_limit = 0 recipient_delimiter = + inet_interfaces = all I have regenerated the ssl keys with the ohlalaweb.com host name. Any ideas or suggestions?

  Read the article

• cannot connect to sql server express from sql server standard

  - by Jackson Sunuwar

  ... like my title says... I cannot connect to my instance on sql server express from sql server standard... I have tried disabling firing wall and checked sqlbrowser is started but for some reason I cannnot connect to my datbase... called server_name\sqlexpress.. I have a virtual machine and a full scale MS SQL Server 2008 R2 running on it... and I have several other vm running sqlexpress. they run fine and I can connect to them using sqlexpress... but when i try to access from sqlserver... I get this error. A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: SQL Network Interfaces, error: 26 - Error Locating Server/Instance Specified) (Microsoft SQL Server, Error: -1) Digging deep into the error, I found this Error Number: -1 Severity: 20 State: 0 and finally this... Program Location: at System.Data.SqlClient.SqlInternalConnection.OnError(SqlException exception, Boolean breakConnection) at System.Data.SqlClient.TdsParser.ThrowExceptionAndWarning(TdsParserStateObject stateObj) at System.Data.SqlClient.TdsParser.Connect(ServerInfo serverInfo, SqlInternalConnectionTds connHandler, Boolean ignoreSniOpenTimeout, Int64 timerExpire, Boolean encrypt, Boolean trustServerCert, Boolean integratedSecurity, SqlConnection owningObject) at System.Data.SqlClient.SqlInternalConnectionTds.AttemptOneLogin(ServerInfo serverInfo, String newPassword, Boolean ignoreSniOpenTimeout, Int64 timerExpire, SqlConnection owningObject) at System.Data.SqlClient.SqlInternalConnectionTds.LoginNoFailover(String host, String newPassword, Boolean redirectedUserInstance, SqlConnection owningObject, SqlConnectionString connectionOptions, Int64 timerStart) at System.Data.SqlClient.SqlInternalConnectionTds.OpenLoginEnlist(SqlConnection owningObject, SqlConnectionString connectionOptions, String newPassword, Boolean redirectedUserInstance) at System.Data.SqlClient.SqlInternalConnectionTds..ctor(DbConnectionPoolIdentity identity, SqlConnectionString connectionOptions, Object providerInfo, String newPassword, SqlConnection owningObject, Boolean redirectedUserInstance) at System.Data.SqlClient.SqlConnectionFactory.CreateConnection(DbConnectionOptions options, Object poolGroupProviderInfo, DbConnectionPool pool, DbConnection owningConnection) at System.Data.ProviderBase.DbConnectionFactory.CreateNonPooledConnection(DbConnection owningConnection, DbConnectionPoolGroup poolGroup) at System.Data.ProviderBase.DbConnectionFactory.GetConnection(DbConnection owningConnection) at System.Data.ProviderBase.DbConnectionClosed.OpenConnection(DbConnection outerConnection, DbConnectionFactory connectionFactory) at System.Data.SqlClient.SqlConnection.Open() at Microsoft.SqlServer.Management.SqlStudio.Explorer.ObjectExplorerService.ValidateConnection(UIConnectionInfo ci, IServerType server) at Microsoft.SqlServer.Management.UI.ConnectionDlg.Connector.ConnectionThreadUser() Firewall is turned off on the VM that's running mssqlserver... I turned of firewall on one of the vm that's running the sqlexpress but I still get the error... can someone please help... thank you

  Read the article

• Dell Inspiron 1564 overheating but fan not switching on, how to diagnose?

  - by Smugrik

  I've got a Dell Inspiron 1564 laptop that is about one and a half years old. Since about a week, the laptop started to overheat, causing it to switch off unexpectedly... The cpu fan is working erratically, it can start to spin for a while, doing its job and cooling down the cpu before it stops, but then the temperature goes up, and the fan doesn't reacts, once the temperature reaches a critical point (over 85 celsius, checked with speedfan...), the laptop switches off... I already cleaned the vents and fan from dust, to no avail, and it was actually quite clean anyway. Drivers and bios are up-to-date, no crapware was ever installed on this machine. I don't know how to diagnose the problem, could it be the temperature sensors that sends wrong information, so the fan doesn't reacts? but then I believe the computer wouldn't detect the overheat and stop... Is there a way I can pin point the problem? Maybe some low-level diagnostic tools to check functionality of sensors and fans??? The warranty is already over so any suggestion would be welcome. Thanks!!

  Read the article

• Get Squid to pass X-Requested-With header

  - by tftd

  I have configured a squid 3.1 proxy server. Everything works great except for the X-Requested-With header. I can't manage to figure out how to pass that header to the site I'm attempting to open via the proxy. This is my current configuration: request_header_access Allow allow all request_header_access Authorization allow all request_header_access WWW-Authenticate allow all request_header_access Proxy-Authorization allow all request_header_access Proxy-Authenticate allow all request_header_access Cache-Control allow all request_header_access Content-Encoding allow all request_header_access Content-Length allow all request_header_access Content-Type allow all request_header_access Date allow all request_header_access Expires allow all request_header_access Host allow all request_header_access If-Modified-Since allow all request_header_access Last-Modified allow all request_header_access Location allow all request_header_access Pragma allow all request_header_access Accept allow all request_header_access Accept-Charset allow all request_header_access Accept-Encoding allow all request_header_access Accept-Language allow all request_header_access Content-Language allow all request_header_access Cookie allow all request_header_access Mime-Version allow all request_header_access Retry-After allow all request_header_access Title allow all request_header_access Connection allow all request_header_access User-Agent allow all request_header_access All deny all #remove all other headers # delete "x-forwarder-for.." headers forwarded_for delete request_header_access Via deny all request_header_access X-Forwarded-For deny all I tried to add this line request_header_access X-Requested-With allow all to the configuration but apparently X-Requested-With is an unknown header name... Apparently I'm missing something?

  Read the article

• CopSSH SFTP -- limit users access to their home directory only

  - by bradvido

  Let me preface this by saying I've read and followed these instructions at the FAQ many times: http://www.itefix.no/i2/node/37 It does not do what the title claims... It allows every user access to every other user's home directory, as well as access to all subfolders below the copssh installation path. I'm only using this for SFTP access and I need my users to be sandboxed into only their home directory. If you know a fool-proof way to lock users down so they can see only their home directory and its subfolders, stop reading now and reply with the solution. The details: Here is exactly what i tried as I followed the FAQ. My copSSH installation directory is: C:\Program Files\CopSSH net localgroup sftp_users /ADD **Create a user group to hold all my SFTP users cacls c:\ /c /e /t /d sftp_users **For that group, deny access at the top level and all levels below cacls "C:\Program Files\CopSSH" /c /e /t /r sftp_users **Allow my user group access to the copSSH installation directory and its subdirectories For each sftp user, I create a new windows user account, then I: net localgroup sftp_users sftp_user_1 /add **Add my user to the group I've created Open the activate user wizard for CopSSH, choosing the user, "/bin/sftponly" and Remove copssh home directory if it exists **Remains checked Create keys for public key authentication **Remains checked Create link to user's real home directory **Remains checked This works, however, every user has access to every other user's home directory as well as the CopSSH root directory.... So I tried denying access for all users to the user home directory: cacls "C:\Program Files\CopSSH\home" /c /e /t /d sftp_users **Deny access for users to the user home directory Then I tried adding permissions on a user-by-user basis for each users home\username folder. However,these permission were not allowed by windows because of the above deny rule i created at the home directory was being inherited and over-riding my allow rule. The next step for me would be to remove the deny rule at the home directory and for each user folder, add a deny rule for every user it doesn't belong to, and add an allow rule for the one user it does belong to. However, as my user list gets long, this will become very cumbersome. Thanks for the help!

  Read the article

• Mac OS X printing to CUPS - More intuitive authentication failure?

  - by Moduspwnens

  We have a network-wide CUPS server that offers authenticated printer access to all our campus users. We've been pretty disappointed with the way Mac clients handle bad printing authentication, though. In any other authentication dialog, when a user types in a bad username or password, the window shakes briefly, allowing the user to re-enter. With printers, this isn't the case. It'll happily accept (and even save to the keychain, if specified) bad credentials. The authentication dialog is dismissed, and the user then has to deal with the print jobs showing up as "On hold (authentication required)". To get their job printed, they need to select it in the printer's queue, click "Resume", then re-enter appropriate credentials. Is there a way to get failed printing authentication to work more intuitively for Mac OS X clients? We're trying to support a BYOD environment, but our end users have been really confused by this. It's made even worse by the way it pre-populates the user's full login name (e.g. "Smith, John"), which tends to make them think to use their local machine passwords.

  Read the article

• 0 connected nodes in datastax opscenter

  - by gansbrest

  Installed opscenterd on the separate node outside of the cluster, but within firewall ( aws security group ). Tested all possible ports between agents and opcenter server. No errors in the log.. 2013-10-30 01:07:23+0000 [FC_Cluster] INFO: Initializing event storage. 2013-10-30 01:07:23+0000 [FC_Cluster] INFO: Attempting to load all persisted alert rules 2013-10-30 01:07:23+0000 [FC_Cluster] INFO: Done loading persisted alert rules 2013-10-30 01:07:23+0000 [FC_Cluster] INFO: Done initializing event storage. 2013-10-30 01:07:23+0000 [FC_Cluster] INFO: Done loading persisted scheduled job descriptions 2013-10-30 01:07:23+0000 [FC_Cluster] INFO: OpsCenter starting up. 2013-10-30 01:07:23+0000 [] INFO: Finished starting new cluster services for FC_Cluster 2013-10-30 01:08:04+0000 [FC_Cluster] INFO: Agent for ip 10.34.10.185 is version u'3.2.2' 2013-10-30 01:08:04+0000 [FC_Cluster] INFO: Agent for ip 10.32.37.251 is version u'3.2.2' 2013-10-30 01:08:04+0000 [FC_Cluster] INFO: Agent for ip 10.82.226.252 is version u'3.2.2' The most interesting part that I can see some data in the opscenter UI, when I stop agents, there is no data displayed, when I start - it show up again, but at the same time it shows 0 connected nodes. Storage capacity is even funnier - 3 of 0 nodes.. Any ideas why that could be happening?

  Read the article

• vagrant and puppet security for ssl certificates

  - by Sirex

  I'm pretty new to vagrant, would someone who knows more about it (and puppet) be able to explain how vagrant deals with the ssl certs needed when making vagrant testing machines that are processing the same node definition as the real production machines ? I run puppet in master / client mode, and I wish to spin up a vagrant version of my puppet production nodes, primarily to test new puppet code against. If my production machine is, say, sql.domain.com I spin up a vagrant machine of, say, sql.vagrant.domain.com. In the vagrant file I then use the puppet_server provisioner, and give a puppet.puppet_node entry of “sql.domain.com” to it gets the same puppet node definition. On the puppet server I use a regex of something like /*.sql.domain.com/ on that node entry so that both the vagrant machine and the real one get that node entry on the puppet server. Finally, I enable auto-signing for *.vagrant.domain.com in puppet's autosign.conf, so the vagrant machine gets signed. So far, so good... However: If one machine on my network gets rooted, say, unimportant.domain.com, what's to stop the attacker changing the hostname on that machine to sql.vagrant.domain.com, deleting the old puppet ssl cert off of it and then re-run puppet with a given node name of sql.domain.com ? The new ssl cert would be autosigned by puppet, match the node name regex, and then this hacked node would get all the juicy information intended for the sql machine ?! One solution I can think of is to avoid autosigning, and put the known puppet ssl cert for the real production machine into the vagrant shared directory, and then have a vagrant ssh job move it into place. The downside of this is I end up with all my ssl certs for each production machine sitting in one git repo (my vagrant repo) and thereby on each developer's machine – which may or may not be an issue, but it dosen't sound like the right way of doing this. tl;dr: How do other people deal with vagrant & puppet ssl certificates for development or testing clones of production machines ?

  Read the article

• Follow cursor location from kile to evince.

  - by D Connors

  I know the title is probably not very clear, so I'll try to be as clear as possible here. I'm running xubuntu on my netbook, and I'm using kile for my latex editing. Since kile is native to kde, I had to manually set it to open pdfs and dvis on evince instead of okular. Now, last time I played around with LaTeX I was using TeXnic center on windows, and it had a very neat feature. Whenever I hit "QuickBuild", not only would it open the output .dvi file, but it would also show me exactly the piece of text I was editing. That is, if I were editing line 13 of the 7th of my document, when I compiled it, the dvi viewer would automatically take me to line 13 on the 7th page of the document, so I wouldn't have to scroll all the way down to it every time I compiled the .tex file. I'm guessing this is a pretty standard feature, and kile probably supports it. But since I don't know what it's called, I'm trying to be clear as to what I'm talking about. Problem is, this feature is not working for me right now, and I'm guessing it's either because evince does not support it, or because I have to manually configure it. Which one is it? And how do I manually configure it, if that's the case?

  Read the article

• SQLVDI error - attempt to release mutex not owned by caller

  - by Chris W

  I've started getting some errors in the App event log of one of our database servers (Windows 2003 & SQL Server 2005). The nightly full database backups are completing successfully however immediately after the job success is written to the event log there is a run of entries that say: SQLVDI: Loc=CVDS. Desc=Release(ClientAliveMutex). ErrorCode=(288)Attempt to release mutex not owned by caller. There's five of these logged - the server itself has more than 20 databases on it which are all backed up successfully. The server is backed up by Bacula using a VSS backup. Has anyone got any ideas what would be causing the errors? They seem to have started after a re-boot on Friday to install some patches which included KB960089. Edit: After getting the errors for a few days they've now stopped without any action on my part other than letting the backups continue as they were. It may be a coincidence but they stopped after Bacula completed its weekly full rather than the daily incremental backup.

  Read the article

• nginx not serving admin static files?

  - by toto_tico

  First, I want to clarify that this error is just for the admin static files. This means my problem is specific just to the static files that corresponds to the Django admin. The rest of the static files are working perfect. Basically my problem is that for some reason I cannot access those admin static files with the ngix server. It works perfect with the micro server of Django and the collect static is doing its job. This means it is putting the files on the expected place in the static folder. The urls are correct but I cannot even access the admin static files directly, but the others I can. So, for example, I am able to access this url (copying it in the browser): myserver.com:8080/static/css/base/base.css but i am not able to access this other url (copying it in the browser): myserver.com:8080/static/admin/css/admin.css I also tried to copy the admin/ directory structure into other_admin_directory_name/. Then I can access myserver.com:8080/static/other_admin_directory_name/css/admin.css Then, it works. So, I checked permissions and everything is fine. I tried to change ADMIN_MEDIA_PREFIX = '/static/admin/' to ADMIN_MEDIA_PREFIX = '/static/other_admin_directory_name/', it doesn't work. This a mistery in itself that I am exploring but still no luck. Finally, and it seems to be an important clue: I tried to copy the admin/ directory structure into admin_and_then_any_suffix/. Then I cannot access myserver.com:8080/static/admin_and_then_any_suffix//css/admin.css So, if the name of the directory starts with admin (for example administration or admin2) it doesn't work. * added thanks to sarnold observation ** the problem seems to be in the nginx configuration file /etc/nginx/sites-available/mysite location /static/admin { alias /home/vl3/.virtualenvs/vl3/lib/python2.7/site-packages/django/contrib/admin/media/; }

  Read the article

• Rsync: General file/folder synchronization

  - by Rey Leonard Amorato

  I have a file server, which is in-charge of pulling a folder tree from multiple workstations on a daily basis. My current method for this is by using rsync, (which works pretty well provided directory names and/or files remain the same) however, when files are renamed or moved about within subdir1, rsync will copy them over to the server, creating duplicates. I have to manually find and delete extraneous files/folders that had been left on the server during previous syncs. Note that I cannot use rsync's --delete flag because any sync from a workstation will then mirror that particular folder tree, instead of merging them to the server. Visual diagram: Server: Workstation1 Workstation2 Workstation(n) Folder* Folder* Folder* Folder* -subdir1 -subdir1 -subdir1 -subdir(n) -file1 -file1 -file2 -file(n) -file2 -file(n) Is there a simple script (preferably in bash, nothing fancy) that can accomplish the deletion of the extraneous files/folders in the event a file is renamed or moved to a different subdir? Is there a different program, much like rsync that can accomplish this task autonomously and in a much simpler manner? I have looked at unison, but I did not like the fact that it keeps a local database for the syncing info. Any tips at all as to how I am supposed to tackle this? Thank you in advanced for your help. EDIT: I have tried unison just recently and I can safely say it is out of the question now. unison is a bi-directional synchronization tool and from my testing, it mirrors the files existing on the server to all workstations. - This is unwanted. preferably, i would want files/folders to stay within their respective workstations and just merge to the server. AKA uni-directional sync; but with renames/moves propagated to the server. I might have to look into Git/Mercurial/Bazaar as mentioned by kyle, but still unsure if they are fit for the job.

  Read the article

• How to transfer files via infrared on Linux?

  - by arielnmz

  I know this is a way too old technology but I've got some files inside a very old cellphone that I need to transfer to a very old computer. So far my Infrared USB device works well, it's detected by the machine (lsusb output): Bus 002 Device 002: ID 0df7:0620 Mobile Action Technology, Inc. MA-620 Infrared Adapter I've tried to send the file over MMS and even email (it lacks bluetooth, not to mention USB). But this cellphones's firmware doesn't let me attach the files. The file was originally transfered via IrDA, and it only has an internal memory (a whole 2 million bytes! whoa!). I found a package called irda-utils, but it seems that there are only two executables: irdaping and irdadump. I think the dump utility might do the job (which as far as I can see it's kind of a version of tcpdump but for IrDA), but I don't even know how to process the received frames. Could this question may be what I'm looking for? EDIT While reading through the Linux Infrared HOWTO I found about the OpenObex project, which may be what I'm looking for...

  Read the article

• Apache2, Tomcat6, and proxy redirects

  - by Randal Hale

  So here is my question - go easy and slow. I'm a GIS Consultant and general hack with linux. I inherited this volunteer job essentially because I knew more than the rest of the team - or the rest of the team isn't as stubborn as I am... With that said a number of people have been mucking around in the server before I got involved so I've been cleaning up a lot of things. The domain names have been changed to protect the innocent. I have a server running Apache2 (port 80) and tomcat6 (8080) running on ubuntu server 10.4. There is a virtual host on Apache2 called "Runner" (the domain is runner.org). I have mod_proxy loaded. I am trying to redirect everyone that visits runner.org to http://some.ip.address:8080/openrunner-webapp/ So far I've gotten runner.org assigned to the apache2 server. Someone set up a redirect in the httpd.conf file but I believe it needs to go into the virtualhost. I tried setting the redirect in the virtualhost as: *ProxyPass / http://localhost:8080/openrunner-webapp All that does is show me the root of the Apache webserver. Anyway I'm stuck

  Read the article

• SSRS 2005 inaccessible after install

  - by Gabriel Guimarães

  Hi I've just installed SQL 2005 and Database Engine is ok, however I can't access it for nothing. When I go to http://localhost/reports I get this prompt for a username and password and it fails with 401.1. When I tried to disable kerberos on the virtual directories, nothing changed. I've tried changing the auth to anonymous and get: Internet Explorer cannot display the webpage. When I access from another machine, I get the prompt only once and get this error. Internet Explorer cannot display the webpage. Can't access this with IE or SSMS 2005. If I try to access with Management Studio i get this error: TITLE: Microsoft SQL Server Management Studio The underlying connection was closed: An unexpected error occurred on a receive. (Microsoft.SqlServer.Management.UI.RSClient) ADDITIONAL INFORMATION: Unable to read data from the transport connection: An existing connection was forcibly closed by the remote host. (System) An existing connection was forcibly closed by the remote host (System) BUTTONS: OK By the way the server info: its a Win 2003 R2 Standard with IIS 6 Can't seem to understand this. Does anyone have a hint?

  Read the article

< Previous Page | 548 549 550 551 552 553 554 555 556 557 558 559  | Next Page >