Search Results

Search found 15160 results on 607 pages for 'boot disk'.

Page 557/607 | < Previous Page | 553 554 555 556 557 558 559 560 561 562 563 564  | Next Page >

• i7-980X at 70% speed

  - by Buxley

  Hi we bought a nice computer to use to solve optimization problems. Intel i7-980X@3,33 GHz with 12 GB of Team Group 1600 MHz DDR3 RAM. When we use Gurobi the computer uses all 12 cores at maximum in the beginning of the solve. However after a while (about 8 hrs) it all cores jump between 65 and 85% When I solve the same models on an i7 930 all cores are at a near 100% level even after longer solution times. We first thought that the Hard disk was the bottleneck since Gurobi writes out nodefiles after the memorylimit is used. However since the new computer have 12 GB of RAM we put the memorylimit to 7 GB so the solver only used the RAM and still with the same performance in the processor. Any ideas about the bottleneck? As I said earlier it works at 100% for the first hours or so . Thanks very much for any answers! Our plan was to overclock it but we can't even get it to work at normal speed yet!

  Read the article

• SRM 4 Test Fails with message for some VM : Error: A specified parameter was not correct.

  - by Setesh

  Here are my architecture : For the protected site 4 Host VSphere Enterprise Plus, each one with 2 HBAs FC connected to the switch fabric, connected to an EMC CX4-120 1 VCenter 1 SRM For the recovery site 2 Hosts Vsphere 4 1 Vcenter 1 SRM 1 CX-4-120 The CX4-120 is connected to the second CX4-120 with ISCSI and the MirrorView / Asynchronous. I synchronise for the time 6 Lun on a FC DAE, 2 on a S-ATA DAE I have allocated 30% of the amount synchronised LUN for the SNAPSHOT us, but I have allocated them only on my S-ATA II DAE. It does not make a problem, my snapshot are correctly active. All the installation is new (hardware and software), installed in January with the last files available in download. I have a strange problem, and it's random, sometimes when I run a test on my RP, some VMs have this error : Error: A specified parameter was not correct. I don't know where to look. Any help is appreciated... PS : I have checked on all the VMs, no Floppy disk or CD attached. PS2 : There is severals VMs with RDM and OCFS2 filesystems on it.

  Read the article

• Amazon EC2 - Free memory

  - by Damo

  We have an amazon ec2 small instance running and over the past few days we noticed that the memory is going down and down. On the small instance, we are running apache and tomcat6 Tomcat is started with the following JVM parameters -Xms32m -Xmx128m -XX:PermSize=128m -XX:MaxPermSize=256m We use nagios to monitor stuff like updates to apply, free disk space and memory. Everything else is behaving as expected but our memory is going down all the time. Our app receives approx half a million hits a day When I shutdown apache and tomcat, and ran free -m, we had only 594mb of memory free out out of the 1.7gb of memory. Not much else is running on the small instance and when running the top command I cannot see where the memory is going. The app we run on tomcat is a grails webapp. Could there be a possibility that there is a memory leak within our application? I read online and folks say that a small amazon instance is perfect for running apach and tomcat. I found a few posts online that showed how to setup apache and tomcat to limit the memory usage and I have already performed those steps. The memory is not being used up as quick but the memory is still decreasing over time. We have other amazone ec2 small instances running grails apps and the memory is fairly standard on those nodes. But they would not be receiving as much traffic Just to add, when I run the top command on the problem server, I cannot see where all the memory is being used Any help with this is greatly appreciated The output of free -m when run on my server is as follows total used free shared buffers cached Mem: 1657 1380 277 0 158 773 -/+ buffers/cache: 447 1209 Swap: 895 0 895 In your opinion, does this look ok? At what stage would the OS give back memory, would it wait to the memory reaches 0% or is this OS dependent?

  Read the article

• Ubuntu 12.04 VirtualBox on powerful W7 quite slow

  - by wnstnsmth

  I own a Thinkpad T420s with 8GB RAM, 160 GB SSD and a quite fast i7 processor. Summa summarum a very fast computer that works perfectly. Now, I am not very impressed by the performance of my Ubuntu 12.04 virtual machine running on VirtualBox 4.1.18. I assume that Virtual Machines are always a bit slower than the guest system, still I think it should be more performant given the hardware settings I give it: 4096 MB RAM 1 CPU without CPU limitation (I would like to give it more but then it does not seem to work - I am not experienced in this maybe somebody could give me advice on this too) Activated PAE/NX, VT-x/AMD-V and Nested Paging 96 MB Graphics Memory (no 2D or 3D acceleration) ~ 14 GB disk space, currently about 7 GB are used Maybe I misconfigured something, could you give me a hint please? Thanks! Edit: What I mean by slow is that for example switching tabs in the browser (whether FF or Chrome) only goes with a 0.5s delay or something, as well as switching application windows and/or double-clicking applications in the dock to get all open windows.. opening Aptana takes about a minute whereas opening something like Photoshop on the guest system takes 5 seconds

  Read the article

• Best way to restrict access to a folder in Dropbox

  - by Joe S

  I currently run a business with around 10 staff members and we currently use Dropbox Pro 100GB to share all of our files. It works very well and is inexpensive, however, I am taking on a number of new staff and would like to move the more sensitive documents into their own, protected folder. Currently, we all share one Dropbox account, I am aware that Dropbox for teams supports this, but it is far too expensive for us as a small company. I have researched a number of solutions: 1) Set up a new standard Dropbox account just for use by management, which will contain all of the sensitive documents, and join the shared folder of the rest of my team to access the rest of the documents. As i understand it, this is not possible with a free account, as any dropbox shared folder added to your account will use up your quota 2) Set up some sort of TrueCrypt container, and install TrueCrypt on each trusted staff member's machine, and store the documents inside that. Would this be difficult to use? I'd imagine the sync-ing would not work so well as the disk would technically be mounted at the time of use and any changes would be a change to the actual container rather than individual files. I was just wondering if anyone knows a way to do this without the drawbacks outlined above? Thanks!

  Read the article

• Datastage 8.7 installs fine on Window7 without any errors but it can not launch localhost:9080 web console

  - by user265273

  When I launch the web console, I get page can not be displayed error. What I have tried so far: I have re-installed DS about 7 times, and each time, I get same errors. I added entries in etc/hosts file for local host and my host name. I have turned off firewall. My hardware/software setup. My host system is window8.1. My vmware workstation is 7. The guest os is windows 7 enterprise x64. I have installed 10g, and given dba role to public. I have installed VS 5, and ms visual c++ 2010 express. I have installed msxml. IE version is 10. Firewall is off. My internet works fine It passed all the DS requirement tests and install completed successfully. When I launch my vmware guest instance, I do get SQL5000c error upon boot which I have tried to ignore in some installs and in some, I used db2systray -clean command to get rid of it. But that has not helped solve the webconsole connect failure to my host. I have spent over 2 weeks exclusively on this issue and badly need some help.

  Read the article

• How to fix Windows 7 when System Recovery Options hangs?

  - by seansand

  The battery power ran out on my HP G60 laptop and it shut down. Even after recharging, Windows 7 will now not start up. After any attempted startup, it bluescreens and takes me to the "Startup Repair (recommended)" / "Start Windows Normally" console screen. "Startup Repair (recommended)" appears to be the right choice, but when I choose it, I get taken to a screen which appears to be System Recovery Options (it's the same wallpaper as the screenshots here: http://www.sevenforums.com/tutorials/668-system-recovery-options.html). However, I just get a cursor with nothing else; no "System Recovery Options" window ever pops up. (A black console screen does pop up for a split-second but too fast to be able to read the text.) The empty screen with cursor hangs indefinitely. System Recovery Options normally runs off of a partition on the laptop hard drive. When I got the laptop, I also created a System Repair Disc (in fact I have more than one) and when I try use any of them; they all result in the same wallpaper and empty screen with lone cursor. Ctrl-Alt-Del does nothing. The computer did not come with a Windows 7 installation disc, so there's no obvious way to reinstall Windows 7. Safe mode does not work; startup fails and I just get sent back to the "Startup Repair (recommended)"/"Start Windows Normally" console screen. "Start in last good state" does not work either, same result as above. Running a memory & hard disk check found no errors. Do I have any options at all? "System Recovery Options" seems to be what I want, but the screen that is supposed to take me to them just hangs.

  Read the article

• Stop Windows 7 from accessing or writing to hard drive unless "told" to by me? (More info inside...)

  - by Jeff

  A confusing question, perhaps, but bear with me. I have two internal HDDs set up in a RAID0 array which I use as mass storage. I access the drive very infrequently (once a day at most) and so I have set up Windows 7's power options to turn off idle disks after only 1 minute. This is fine, and the disks are turned off most of the time. However, I notice that Windows sometimes spins up the drives when I really, really don't want or need it to. This causes a 30 second delay as both drives spin up and lock up my system. Some examples of when this happens: 1) When I'm installing something using Windows Installer or Installshield; it seems to me as if they're using the drive with most available free space as the installer cache location... so my big RAID drive has to spin up! Most annoying. 2) Apparently, when I open a Java-based program which resides on my system drive and has nothing to do with my RAID drive! 3) At boot-up and shut-down time. At shutdown the drive spin up only for the computer to immediately shut down! Incredibly frustrating! I've already tried changing the letter of the drive, and at some points have removed the drive letter entirely, which solves the first two issues above. So my question (FINALLY!) is this: is there any way I can mark this drive as being for "storage only", so Windows basically does not see it at all until I actually invoke it somehow? Or is there any way I could set it up so that only specific programs have write access to it? For example, download managers, TeraCopy, etc. etc.? Basically I want it to be a "ghost drive" until I'm ready to use it and to stop Windows from spinning it up all the damn time! Thank you. :)

  Read the article

• Missing Memory on Windows Server 2008

  - by Chris Lively

  I have a windows 2008 x64 server with 8GB of RAM installed. Task Manager and Resource Monitor both insist that 7.5GB of the RAM is in use. However, the memory list under Processes (Memory Private Bytes) doesn't add up. I do have Show Processes from all users checked and hand adding the numbers I come up with about 3.5GB of RAM. I also looked at the latest copy of SysInternals Process Explorer. And neither the Private Bytes or Working Set adds up to more than about 3.5GB of RAM in use. What's going on? ===== Update: I bounced the server to see what would happen with the memory utilization. After boot and regular operations began it sat at 3GB of RAM usage. 18 hours later, it's back up to 6.8GB of usage with no indication as to where the additional 3.5GB or so of RAM is being used. Here are links to screen shots of the resource monitor and task manager: Resource Monitor Task Manager Update 2: Well, I believe I located the problem. When I detached one of the larger databases from my sql server the amount of ram shown as "in use" dropped drastically. The Memory Private Bytes count barely moved. So I'm guessing that SQL server has some way of allocating memory where it doesn't really show up in any of the monitors. I went further and created a new database file, then transferred all of the data from the one I detached. Even though it has the same data, and the same transactions going through it, the memory in use has stayed low. Maybe there was some corruption in the DB? I'll leave it to the DB gods and go searching for another "problem" ;)

  Read the article

• OpenVZ container is running but does not show in vzlist nor can I find the private/conf files for the container

  - by Kakeakeai

  I was creating a new OpenVZ container on one of our VPS Nodes while the power went out for that machine. After bringing the machine back online I could no longer access the container CTID=101. I could not destroy it using "vzctl destroy 101", I can not enter or control it, and "vzlist -a" does NOT display any containers at all (this was a fresh node and the first container was being created). I decided to create a new container at this point assuming that the old container just was not saved for some reason. However when I go to add the ip/host to the new container I get a warning that the IP is already in use. After doing a ping to the IP I realized there was a machine on that IP. I SSH into the machine and discover it is the OLD container that some how is orphaned. I can not find it on the filesystem, I can not find it using VZ commands, and It is set to start on Node boot so it is impossible to shutdown (even ssh in and typing the "shutdown now" command just reboots the container not shut it down). Is this a flaw in OpenVZ or am I missing something? I have all the outputs and logs if needed. Thank you all so much in advance.

  Read the article

• Copy a harddrive from a failed desktop machine using a second working one.

  - by MrEyes

  Heres the scenario: I have PC-A, an old PC that runs Windows XP but now refuses to boot due to a failed motherboard (or maybe PSU). This PC has a single 80gb IDE drive. I also have PC-B, running Windows Vista, this is working fine. I want to copy all the data off PC-As HDD onto PC-B. To do this I have taken the HDD out of PC-A and connected it as a slave to PC-B. PC-B now boots and sees the additional drive. However, when I attempt to access/copy user folders (i.e. Documents and Settings/[username]/*) I am told that I cannot access the folders due to user permissions. I am doing this under an adminstrator account on PC-B. So the question is, how can I "backup" the data? Preferably without making any changes to the drive contents. The reason for this is that it is possible that PC-A is failing due to a bad PSU, so I intend to replace it before writing off the machine. However I would feel much happier if I had a backup of the data on the HDD.

  Read the article

• Force Installing a Radeon HD 2100 on Windows 8

  - by Click Ok

  I'm trying force installing a Radeon HD 2100 on Windows 8. I've found that link from AMD with the drivers for Windows7: http://support.amd.com/us/gpudownload/windows/legacy/Pages/legacy-radeonaiw-vista64.aspx I know too that AMD will stop support Radeon HD 400 and older: http://www.techspot.com/news/48321-amd-drops-windows-8-support-for-radeon-hd-4000-and-older.html Now, let's go to the problem. If I try install the 12.6 driver, Windows will stick with the "basic display adapter", and this is bad for 3d games like Minecraft, that runs really slow now compared with the previous Windows7 installation. Forcing install the catalyst driver can help to fix it. So, I follow that steps: Extract the Catalist Driver (C:\AMD\Support\12-6-legacy_vista_win7_64_dd_ccc_whql) Right click the "basic display adapter" on device manager, and "update driver" Search on PC I will choose the driver "With Disk" "C:\AMD\Support\12-6-legacy_vista_win7_64_dd_ccc_whql\Packages\Drivers\Display\W76A_INF" There is a big list of drivers and the nearest driver to HD 2100 is "Radeon HD 2350 Series" My questions: Why isn't "Radeon HD 2100 Series" listed? (or Where is it listed?) In theory it must be listed" The first link above show that "This article applies to the following configuration(s):" (...) "AMD Radeon HD 2000 Series" Am I doing something wrong?

  Read the article

• Volume is no longer showing in Raid Controller BIOS and in Windows

  - by Gordon

  Hi all, I have installed some critical Windows Updates yesterday and now my external RAID Volume no longer shows in Windows Vista x64. All updates went through successfully. From their description, I cannot see how they should relate to the issue, but this is the only change that happened, so who knows. Anyway, here is the details: I have an external eSata enclosure that is running on a SiI4726 controller. I can connect to the controller with it's management utility from the computer the enclosure is connected to. The three drives in the enclosure show up as JBODs. I had those drives configured to be one logical RAID5 drive. RAID management is done through a SiI3132 SoftRaid controller. The Raid Management Utility just shows empty channels where it usually shows the Raid Group. In the Windows Disk Manager, I can see an unknown unitialized device. This is fine according to the setup manual. What it doesn't show is my Raid drive. It's gone. Also, when booting Windows, the BIOS of the controller used to show the RAID volume before booting the OS. This is not happening anymore. Updating drivers and firmware did not help. I have made sure the drivers and firmware are compatible to each others. And like I said, it used to work before. Any clues?

  Read the article

• Problems reviving old pc including graphics card issue.

  - by Mick

  I have a PC that seemed to have died years ago that I am trying to revive. It has a dual core athlon processor and a gigabyte motherboard. It had two dual output graphics cards, and I have long since forgotten which output would print out the diagnostic information as the PC starts up. Also I suspect that the resolution set on all the monitors was probably higher than my current single monitor is capable of displaying. The motherboard also has a built in graphics card, so I thought it may be simplest to remove both the graphics cards and plug my monitor into the onboard graphics just while I get things going. Does that seem sensible? Now the other problem: The PC has two hard drives. I have no idea which one is the primary one it is attempting to boot from. When I power up, the fan comes on and I hear some chuga-chuga-pause chuga-chuga-pause repeat indefinitely. I'm not sure which device is making the noise. There are no-beeps at any time. I see nothing on the screen at any time, not even for a second. Any suggestions? EDIT: If T start up the PC without the power connected to the CDrom there is no chuga-chugan noise.

  Read the article

• Virtual Server HDD shrinks without apparent reason

  - by Christian

  We have a virtual hosted Linux server, and in the last few months every now and then the HDD shrinks from 400GB down to the exact byte count that is in use. All existing data can be downloaded and displayed without a problem, but we can't upload or edit any files because of the "full" hard drive. Here is a screenshot, where "size" should be 400GB: This has happened twice before, and again today. The last times, when I reported the issue to the host, they said "that isn't possible, you must be doing it wrong", but soon after the call, the problem vanished without us doing anything, so I suppose that they have some kind of problem they're not willing to admit. Even after the fact, they acted like nothing was wrong and wrote me a mail in which they explained that I can use "df -h" to view available disk space (well duh, how do you think I noticed this particular issue?). Questions about if and what they had done were ignored. It has happened around the 25th to 28th of the month, so I suspect that they might have a cronjob running every 30 days or so which wreaks havoc with some VM configs. I just want to understand the problem, but the host support hasn't been very helpful in that regard. I have tried Googling the issue, but any combination of search terms I can come up with just gives me tutorials on how to change HDD size in a virtual machine. a) What could be the cause of shrinking HDD size in a Ubuntu 12.04.3 LTS server? Could there be anything in our virtual machine or is it more likely to be an issue with the vm host? b) Can I do anything about it without needing to contact the host's support? c) Is there anyway I can prevent this from happening at all?

  Read the article

• HDD dead forever???

  - by Roberto

  Yesterday I turned on my computer and it couldn't boot. I found out the hd (320GB SATA Seagate Momentus 7200.3 for notebook) was broken, it couldn't be recognized by the BIOS. I have another of the same hd, so I exchanged the boards. I found out that there is a problem on its board since my good hd didn't work. But the broken hd doesn't work with the good board as well: it can be recognized but when I insert a Windows Instalation DVD it says the hd is 0GB. I put it in a case and use it in another computer via USB, and but it doesn't show up in the "My Computer". I used a software to recover files called "GetDataBack for NTFS", it recognized the hd but with the wrong size (2TB). I try to make it read the hd but it get an I/O error reading sector. It tries to read, the hd spins... So, since I'm using a good board on it, the problem seems to be internal. Is there anything someone could do recover the files from it?

  Read the article

• How can I recover my data from a damaged hard drive?

  - by krk

  a few days ago when I was working on windows my laptop was beaten on the side where the hard drive is located. As a result, it was damaged and I couldn't access the windows partition. I had to boot the linux one, which is working without any trouble. I have 2 partition formatted with ntfs, the one with windows on it, and the other one intended to store data. I mounted the windows partition from ubuntu and I could see all my files. But when I tried to mount the data partition it was impossible. It threw me an error, it couldn't recognize ntfs partition. I try to copy the damaged disk into an external hard drive using the command: dd if=/dev/sda of=/dev/sdb conv=noerror,sync The progress stopped at 60%. I was still unable to mount the data partition. Now I'm trying to backup my files using an utility called Photorec. The problem is that it is recovering my files in a disorderly way, it is all mixed up and I need my original directory structure, it will become an endless task to organize the files as they were before. Is there any way I can get my partition back?

  Read the article

• Can't get 1440x900 resolution with GRUB2 although vbeinfo says it's available

  - by TomSW

  I'm trying to use GRUB2 in graphical mode with 1440x900 resolution, but the result is always garbled nonsense: the highest resolution I can get is 1280x800. Word is from googling that long as vbeinfo lists a resolution, GRUB2 can use it. This doesn't seem to be true: vbeinfo says that 1440x900 is available but it doesn't work. Testing it from the GRUB2 command line: set gxfmode=1440x900 terminal_output gfxterm # -> garbled nonsense # back to trusty 640x480 terminal_output console The graphics card is an Intel GM965. Once linux boots the framebuffer switches to 1440x900. Added after epheminent's reply and various experiments vbeinfo lists two sets of modes. The first set runs from 0x160 to 0x16b, with resolutions 768x480, 960x600, 1280x800 and 1440x900 Then - after a bunch of text-only modes - the second set, containing resolutions 1024x768, 800x600, and 640x480 The first set of modes aren't altered by 915resolution. They all work except 1440x900. The resolution of modes in the second set can be altered using the 915resolution module / command available in GRUB2 = 1.99. # in /boot/grub/grub.cfg insmod 915resolution # 30, 32, 34 all work for me: all that varies is which modes are altered 915resolution 30 1440 900 # setting an impossible resolution changes the mode to "text-only" # in my case 1280x1024 is not supported 915resolution 30 1280 1024 Clearly, 1440x900 should just work: adding it with 915resolution is just a workaround.

  Read the article

• (Windows 7) Shared External Drive Permission Issues

  - by connec

  So, say I share my system (C) drive through windows (E.g. properties -> Sharing -> Advanced Sharing -> Share this Folder). I can then access this drive at \\Comp\C on another networked computer - all is well. However, if I insert a removable (USB) disk, say "E", and proceed to share it the same way, when I attempt to access \\Comp\E (either directly or through browsing) I get an error: Windows cannot access \\Comp\E You do not have permission to access \\Comp\E. Contact your network administrator to request access. Now, the permissions (Advanced Sharing -> Permissions) are set with "Everyone" having read access (same as the internal drive), so this doesn't make a lot of sense. Also of note, I have an SSH server on my computer (through Cygwin) and even through SSH (logging in as an administrator user) I cannot access /cygdrive/e (although /cygdrive/c is accessible). As a final note, the drive is of course accessible on the host machine (E:\), and also at \\Comp\E on the host machine.

  Read the article

• Grub Installation Failed: Fatal Error ... now what I do?

  - by eklavya

  I know there are some threads that touch this but I feel I have done something uniquely stupid. hence the post and plea for help. I am a beginner @ Linux. So I have a PC with a HDD (hard disk drive) and SSD (solid state drive) It was running Linux Mint /dev/sda1 - HDD Partition 1 - 2 TB (mounted this is /home /dev/sda2 - HDD Partition 2 - 1 TB (separate back up drive, i was backing up files to this) /dev/sdb1 - SSD Partition 1 - 100 GB (OS) /dev/sdb2 - SSD Partition 2 - 20 GB (Swap) The operating system was Linux Mint and was installed on the /dev/sdb1 i.e the solid state drive. I had partitioned off the sda into 2 TB and 1TB and presented the 2 TB as the /home to the OS. Anyway last night I decided to make a return to Ubuntu via the path of Elementary OS. Everything went fine with the install until it stated that GRUB installed failed and this was a Fatal error (no kidding I said). No I am stuck. I have definitely done something wrong and don't know what it is... My biggest pain is the files on the /dev/sda2. I want to save these before I try something drastic like wiping off the /dev/sda completely. So I have the following questions... Can I use a liveCD USB to save these files ? I can see the /dev/sda2 but was unable to access the files in the liveCD last not least ... how do I fix the main issue here. Why could the OS not install GRUB 2b... why is my SSD the /dev/sdb ... and not /dev/sda. Does that have something to do with it that my master boot record sits on the HDD /dev/sda and not /dev/sdb

  Read the article

• Subversion COPY/MOVE - File not found: transaction 'XXX-XX'

  - by theplatz

  I'm attempting to create a branch in one of my subversion repositories and keep running into an error. No mater what is done, I keep getting the following: File not found: transaction '3062-2e6', path '/Software/XXXXXX/branches/testbranch' I've noticed that the first part of the '3063-3e6' in the above message is the last successful committed revision in the repository. My apache logs don't give much more information: [Wed Nov 24 14:10:38 2010] [error] [client x.x.x.x] Could not MOVE/COPY /svn/p070361/!svn/bc/3049/Software/SXXXXXX/trunk. [404, #0] [Wed Nov 24 14:10:38 2010] [error] [client x.x.x.x] Unable to make a filesystem copy. [404, #160013] [Wed Nov 24 14:10:38 2010] [error] [client x.x.x.x] File not found: transaction '3059-2e2', path '/Software/XXXXXX/branches/testbranch' [404, #160013] This is all happening on a server with an nginx frontend that proxies to Apache for the subversion bits. Other repositories are able to branch fine and I was able to create the branch using file:/// from the command line on the server this is occurring on. The permissions on this repository match every other repository and disk space is not an issue.

  Read the article

• Windows takes a very long time to shut down even in safe mode

  - by user1526247

  On Windows 7 the computer freezes for about 5 minutes once it gets to "Shutting down...". I can't remember when it started happening. I just lived with it for a while. The first thing I tried was a full scan using Microsoft Security Essentials. This did not solve the problem. I then went into msconfig and turned off everything I could get away with in the startup and services tabs. This did not solve the problem. I then uninstalled every program on this computer save the most basic programs. This did not solve the problem (did not uninstall drivers or catalyst). I then went through and turned off every single service and did a reboot. This did not solve the problem. I then booted into safe mode and just tried shutting it down. The problem even happens in safe mode. I have tried examining the event logs but with no success. They just say things like "blah blah has entered the stopped state" with no real clues about what program is causing me all this grief. *it may be worth noting that Ubuntu is installed on the same computer and the ubuntu boot loader is the one being used.

  Read the article

• Giving the root user priority to maintain Debian (while server collapsing under heavy load)

  - by Saix

  Is there any way to setup Debian to prioritize any or specific root's activity before every other? For instance, several times per year something gets wrong (usually man's fault by overstressing apache/mysql) and system gets unresponsive under heavy load like 200 (8-core cpu). I know there are limits for php scripts to run then kill, but that's not the way because this limit has to be at least 45 minutes long. The problem is, until I'm able to login via SSH and let apache/mysql restart under this server stress, it nearly hits these 45 minutes anyway. Also hardware restart causing usually to run fsck at boot time on all harddrives since it's usually pretty long the box haven't been restarted. I was told it's really not good idea disabling fsck but then again, it takes more then hour to complete. What is the fastest way to restart apache/mysql? Is there any way to give ssh users or root user higher priority so the logging in and completing these restarts (rather stops though) commands wouldn't take so long? One comes to my mind.. use NICE for apache/mysql but no way. I can't risk limiting those two vital apps 24/7 or could I? I'm a little bit scared if any other system process wouldn't slow the pages down too much. Any backup process, swap (if any) etc. There is pretty heavy PHP framework with 20k visits a day, so it needs every hw/sw resource available. I can't throttle it the whole time, just in certain points when system gets unresponsive, so I could maintain it.

  Read the article

• Install Windows 8 on SSD and Program & Users on HDD

  - by Foe

  I have been dealing with a few problems while installing Windows 8 on my computer. On my old configuration, I had Windows 7 installed on my 60Go SSD, and my programs and user data on my 1To HDD, thanks to relative links. Yet, while installing Windows 8 on my SSD, he made a small partition on my HDD "System related". Plus, I'm afraid using only links is a bit cheap, and I saw lots of people messing with their registry when trying to put user data on another drive. I read a lot about optimizing Windows 8 for SSD, putting Users on another drive, and very similar situation that didn't quite correspond to what I was trying to achieve. Here's what I tried : http://www.eightforums.com/tutorials/4275-user-profiles-relocate-another-partition-disk.html Booting on Audit mode and using an XML to relocate Users didn't work as the specified version in the file is a test one, and I don't what to enter if I'm using the last release. Booting with the install DVD in repair mode to do a copy of the User and create a relative link, resulting in an error on the logon screen while entering my password saying that "The profile can't be load" (average translation of my error from french to english) Do anyone know how to do a clean separated install of Windows 8, with OS on a drive, and the other data on a second one ? Thanks.

  Read the article

• How to fix high Load_Cycle_Count laptop drive (TOSHIBA MK6006GAH in Vaio TX1XP)?

  - by Sam Brightman

  Hoping someone knows exactly what's going on here. It seems this drive has some combination of aggressive power saving settings and Ubuntu defaults that has massively increased the Load_Cycle_Count for the drive: https://wiki.ubuntu.com/DanielHahler/Bug59695 So the drive is now so slow that it cannot boot because it takes long enough to access the data that the kernel will not recognise it properly. I'm not worried about the data on the drive, but would really like to keep the laptop functioning. There is some indication that this is possible because the figure is still low 200,000s and most drives supposedly go to 600,000. Additionally, SMART tests pass and consider the drive healthy and without errors. But the really surprising thing was when I ran mhdd... Every single read came up red (slow) until I pressed 'R' for reset drive. I noticed the next read was normal speed, so held down 'R'. Magically the drive read perfectly for as long as I held the key BUT resumed slow (and noisy) seeking/reading after releasing. I don't think the source code to mhdd is available, so I'm not exactly sure what this means (besides, I don't know enough low-level HDD stuff either). It seems like the drive should be able to work, but is stuck trying to power save or something. There are no BIOS options on the laptop. Does anyone know how I can stop the drive from doing extremely slow/noisy operations like this? Or is constantly resetting the drive also damanging, and only causing it to work well by luck (i.e. not a suggestion that it's fixable)?

  Read the article

< Previous Page | 553 554 555 556 557 558 559 560 561 562 563 564  | Next Page >