Search Results

Search found 93609 results on 3745 pages for 'one terrorist'.

Page 560/3745 | < Previous Page | 556 557 558 559 560 561 562 563 564 565 566 567  | Next Page >

  • Mergesort : Revision

    - by stan
    Does merge sort work by; taking a list of values splitting it in to two take the first element of each list, the lowest value one goes in to a new list(and i guess removed from the original). comare the next two numbers - do this until one list is empty, then place the rest of the other list at the end ofthe nw list? Also, what are the ramifications of doing this on a linked list? Thanks

    Read the article

  • How to connect 2 routers (Asmax and D-link) RJ11 vs RJ45 issue

    - by piobyz
    I just bought a new router, D-link DSL 2641B and want to connect it to another one, provided by my ISP, Asmax AR 804MP. Previously, I had Linksys WRT350N, and there was no problem, while I had Ethernet cable plugged in to one of LAN ports in Asmax and INTERNET(RJ45) port in Linksys, connection used PPPoE protocol -- worked OK. D-link has DSL(RJ11) port (which I don't want to use as Asmax replacement, while there is a separate Ethernet cable with a TV plugged to Asmax, which I don't want to configure from scratch on D-link). How should I connect my new D-link to work with Asmax? Via DSL port? Via one of the LAN ports (in which case I probably should change the purpose of this port in the config, I guess?). I tried connecting D-link both ways: LAN(ASMAX) to LAN(DLINK) LAN(ASMAX) to DSL(DLINK) (using RJ11 - RJ45 cable) I hope there is some setting in the DLINK's config that I overlooked. I haven't tried to see what's in ASMAX's config, but I guess I don't need to change anything there, while Linksys worked just fine? The only difference I see, is that D-link has RJ11 DSL port as WAN, and Linksys has RJ45 (called by them INTERNET) as a main WAN port.

    Read the article

  • How to connect 2 routers (Asmax and D-link) RJ11 vs RJ45 issue

    - by piobyz
    I just bought a new router, D-link DSL 2641B and want to connect it to another one, provided by my ISP, Asmax AR 804MP. Previously, I had Linksys WRT350N, and there was no problem, while I had Ethernet cable plugged in to one of LAN ports in Asmax and INTERNET(RJ45) port in Linksys, connection used PPPoE protocol -- worked OK. D-link has DSL(RJ11) port (which I don't want to use as Asmax replacement, while there is a separate Ethernet cable with a TV plugged to Asmax, which I don't want to configure from scratch on D-link). How should I connect my new D-link to work with Asmax? Via DSL port? Via one of the LAN ports (in which case I probably should change the purpose of this port in the config, I guess?). I tried connecting D-link both ways: LAN(ASMAX) to LAN(DLINK) LAN(ASMAX) to DSL(DLINK) (using RJ11 - RJ45 cable) I hope there is some setting in the DLINK's config that I overlooked. I haven't tried to see what's in ASMAX's config, but I guess I don't need to change anything there, while Linksys worked just fine? The only difference I see, is that D-link has RJ11 DSL port as WAN, and Linksys has RJ45 (called by them INTERNET) as a main WAN port.

    Read the article

  • SSL in IIS 7 on a subdomain in a web farm

    - by justjoshingyou
    I have been having one of the most frustrating days in my entire IT career. I am trying to install an SSL certificate on a subdomain in a web farm. http://shop.mydomain.com needs to ALWAYS be forced to https://shop.mydomain.com I have a temporary cert issued from verisign on shop.mydomain.com I have installed the cert on the server. The website for shop.mydomain.com is set as a host header in IIS with the DNS entry pointed to the same IP as mydomain.com - which is our load balancer. I actually have 2 load balancers (as needed by our ISP). One redirects all traffic on port 80 out to the different servers on port 80. The other pushes out port 443 to the servers on port 443. shop.mydomain.com is to be the only site protected by SSL at this time. When I add the binding and I navigate to https://shop.mydomain.com it pops up with a warning about the cert being invalid (assumed because this is a test cert), and then it sends the user to http. So, I checked the box "Require SSL and it redirects to http://shop.mydomain.com/default.aspx and displayes an ASP.NET 404 error message. (not the IIS 404 error) I tried removing the binding on the site to port 80 as well with no luck. I am nearly ready to crawl under my desk into the fetal position. How on earth do I make this work? I can't even get it to work on one machine, let alone in the load balanced environment.

    Read the article

  • Detect when application is running in a VM environment

    - by Malcolm
    Looking for ideas on how to detect when our Windows application is running in one of the following VM environments. Some starter ideas for detection are in parentheses. There may be (much) better detection techniques - the starter ideas I've come up with are based on my Google research. VMWare (looking for the presence of optional VMware Tools is one way) Microsoft Virtual PC (have a device named "Virtual HD" for their IDE disks, "MS Virtual SCSI Disk Device" for their SCSI disks) Citrix Xen Sun Virtual Box Thank you, Malcolm

    Read the article

  • Perl copy directory excluding some files

    - by user65457
    In my Perl code, I need to copy a directory from one location to another on the same host excluding some files/patterns (e.g. *.log, ./myDir/abc.cl). What would be the optimum way of doing this in Perl across all the platforms? On windows, xcopy is one such solution. On unix platforms, is there a way to do this in perl?

    Read the article

  • What speed are Wi-Fi management and control frames sent at?

    - by Bryce Thomas
    There are a bunch of different 802.11 Wi-Fi standards, e.g. 802.11a, 802.11b, 802.11g, 802.11n etc. that all support different speeds. Wi-Fi frames are generally categorised as one of the following: Data frames - carry the actual application data Control frames - coordinate when its safe to send/reduce collisions Management frames - handle connection discovery/setup/tear down (e.g. AP discovery, association, disassociation) My question is about whether all these frames, and specifically management frames, are transmitted at the fastest supported speed available, or whether certain classes of frames are transmitted at some lowest common denominator speed. I have noticed that when I put an 802.11b/g only device into monitor mode and capture traffic over the air, I still see management frames (e.g. association/disassociation) being transmitted between my phone and AP which are both 802.11n, even though 802.11n has a higher transfer rate. So I am imagining one of two possibilities: My 802.11n phone/AP had to negotiate a slower speed for some reason and that's why I can see their frames on my 802.11b/g monitoring device. Management frames (and perhaps control frames also?) are sent at a lower speed, and it's only data frames that are transmitted faster with newer 802.11 standards. The reason I would like to know which one of these two possibilities (or perhaps a third possibility) is the case is that I want to capture management frames, and need to know whether using an 802.11b/g card is going to lead to me missing some frames sent at higher speeds than the monitoring card can observe. If management frames are indeed sent at a slower rate, then it's all good. If I just happen to be seeing the management frames because my phone/AP have negotiated a slower rate though, then I need to reconsider what card I use for packet capture.

    Read the article

  • Heterogeneous NSTreeController

    - by andyvn22
    I have an NSTreeController (supplying content to an NSOutlineView). I'd like the top-level objects to be of one class, and all other objects (so, children at any level) to be of another. What's the best way to go about this? I'll need to somehow change the behavior of at least add, addChild, insert, and insertChild, I suppose. I was hoping, though, to find a simple way to account for this in only one location, rather than changing four separate methods.

    Read the article

  • How to configure VirtualBox server for performance at home

    - by BluJai
    I currently have two physical Ubuntu Server 10.10 servers at home: one serves as our firewall/router/DHCP/VPN server and the other performs double-duty as a file server and a VirtualBox host for an Ubuntu Desktop 10.10 machine which I use from remote connections (via NoMachine) for many thin-client purposes which are irrelevant to my question. What I'd like to accomplish is to consolidate the two physical machines into one which is a dedicated VirtualBox host (most likely running Ubuntu Server 10.10). Note that I'd like to stick with VirtualBox (if possible) because I'm most comfortable with it and use it on a daily basis at both home and work. Specifically, I plan to have one VM set up as file server, another as the firewall/router/DHCP/VPN (or possibly split those a bit) and a third, which is the only current VM (already VirtualBox), which is the thin-client host. My question comes down to performance and/or recommendations about the file server VM. The file server hosts about 6 terabytes of data across 4 drives. What I'd like to do is use raw disk access from the VM directly to the existing disks. However, I'm curious what performance advantage/disadvantage that would have as compared to using shared folders from the VM host and basically just have the whole drive served as a shared folder to the VM which would then serve it to the other machines on the network. I don't know if virtual disks would even work in this scenario and I certainly wouldn't want a drive to be filled with just a single file which is 1.5 TB (disk image). To add understanding of context, but not to get additional advice, I want to virtualize these machines because I intend to regularly use the snapshot capabilities of VirtualBox for the system disks (which will be virtual drives) of the VMs and I have some physical space/power needs to address (as I mentioned, this is at home).

    Read the article

  • ASP.NET - Nested Custom Templates

    - by Echilon
    I'm thinking about converting a few usercontrols to use templates instead. One of these is my own UC which contains some controls, one of which is a repeater. Is it possible to specifcy a template for the second level usercontrol from the template for the first (which would be on the page)?

    Read the article

  • Cooling for a small server room

    - by John Zwinck
    I have a server room about 12 feet square with an unfinished ceiling (exposed ducts and wiring). It houses a few servers (about ten, 1U and 2U) and some networking gear (four 1U switches, three routers, three modems, two cable boxes). With the door closed, it runs around 80 degrees Fahrenheit with half the servers turned on. When I turned on all the servers it reached 86 before I chickened out and propped the door open. The room is adjacent to air-conditioned office space, but does not itself have dedicated air conditioning. The ventilation for this room seems to be limited to one duct coming in at ceiling level, with a powered fan to draw air in, and one duct at ceiling level to allow air to flow out (it seems like it may just go into the drop ceiling cavity in the adjacent room). The adjacent office space stays fairly cool, but I'd prefer not to leave the door propped open all the time. There is both 110v and 208v service in the room, and plenty of power available. But there are no windows, and no floor drains (in a pinch we might be able to run a condensation hose through a small hole we'd drill in the wall to a nearby sink area, but only if absolutely necessary). I've considered portable A/C units, but I'm not sure on sizing and a lot less sure how we would run the exhaust hose(s). I suppose we could point one at the existing room exhaust duct (air return), but substantially modifying the duct is probably a no-no. I've also considered installing a fan box in the door of the room, but I'm concerned that this will only drop the temperature a little. Even right now, with all the equipment on, the room is at 83 degrees with the door open. And the main building A/C turns off daily at 6 PM to conserve energy, so the adjacent room temperature rises at night. How would you cool this room? Let's say the goal is to bring the temperature with everything running from a steady state of around 90 degrees down to 75 (equivalently, to offset the heat produced by ten 1U servers).

    Read the article

  • DropDownList doesn't postback on SelectedIndexChanged

    - by Sergey Volegov
    I'm writing an ASP.Net webform with some DropDownList controls on it. Then user changes selected item in one of dropdowns, ASP.Net doesn't seem to handle SelectedIndexChanged event until form is submitted with a 'Submit' button click. How do I make my dropdowns handle SelectedIndexChanged instantly? P.S. It's a classic question I have answered too many times, but it seems no one asked it before on stackoverflow.

    Read the article

  • .htaccess redirect

    - by joesalvator
    I have a magento site oscommerce, I need it to redirect to httpsa I already have the cert installed I just need to change the htaccess file but i dont know which one the one in the root? please help

    Read the article

  • Email bouncing sent from Google

    - by davidmck
    I'm hoping someone here has an idea of where to look next. We have a domain we support which has email sent to it from one particular user bounce with the following message: Delivery to the following recipient failed permanently: [email protected] Technical details of permanent failure: Google tried to deliver your message, but it was rejected by the recipient domain. We recommend contacting the other email provider for further information about the cause of this error. The error that the other server returned was: 550 550 Unrouteable address (state 14). We only have reports of bouncing form this one particular user (who is someone we don't support - except they'd like to be able to contact our customer and we're trying to figure out if the problem is on our end). Many people can successfully send to this domain and the user who is getting bounce messages can send to other domains that we support (so it's clearly something specific with the princetonscoop.com domain and not our setup in general). I've reviewed the MX records multiple times and the server logs don't show a connection which generates this error (in fact this error is not one that our mail server would ever return). So it appears that google is contacting a different mail server for some reason. I have tested sending from my gmail account and that works. I believe the sender is using a google-apps account (the account they are using is from their own domain, not a gmail account). Any ideas on what might be happening here or what to test/investigate next? Thanks.

    Read the article

  • NETKEY IPsec and ARP

    - by Shawn J. Goff
    I'm wondering if I have the correct routing setup for an IPsec tunnel. I have control over the IPsec endpoints and the hosts connected to one side. These hosts are connecting to the tunnel so that they have access to the network on the other side of what I will call the IPsec server. I don't have control of the network upstream of this server. Normally, the IPsec server will not respond to ARP requests for the hosts on the other side of the tunnel. So when a packet arrives for one of my hosts the server gets ARP requests, but the upstream router gets no response, and cannot construct the ethernet frame to send me the packets. If I was using one of the swan stacks, I would have a separate interface, and I'd probably just need to turn on proxyarp, but I'm using NETKEY, which doesn't use a separate interface for the tunnel. To solve the problem for now, I have added an eth0.5 vlan to the IPsec server, turned on proxyarp for that interface, and added all routes my hosts addresses to that interface so that it will respond to those ARP requests (and will therefore get relevant packets routed to it). This works, but it feels wrong. What is the correct way to get the upstream router to send me the traffic for these hosts?

    Read the article

  • How does the iPhone know which OpenGL ES context to use between 1.1 and 2.0?

    - by Moshe
    I've been digging around the net recently and noticed some video tutorials show an older template (pre SDK 3.2) with one OpenGL ES context. Now there are two of them, which, I've gleaned are the two versions of OpenGL ES available on the newer iMobile devices. Can I just use the older one or do I need to do everything twice? How do I tell the iPhone to use the older context, or will it do so automatically?

    Read the article

  • Git - ssh key / ip address

    - by Steve
    When I set up Git, I did it while using a dsl modem, and my ip isn't static, so when I generated the ssh keys for Git, it was based on that ip. When I'm assigned an ip other than the one used to generate the ssh Git keys, I can manually change the ip address to the one used to generate the keys. What are my other options to bypass this step? Dynamic DNS? Is there another way?

    Read the article

  • Don't break header/footer when making page landscape format

    - by Steeven
    I have a document with a footer with page numbering and a header with some centered text. Long story short: I flipped one page to landscape format. Long story long: I made a forced page break to get a blank page. I then highlighted this page (that is, I highlighted the empty line on this page) and went to the page proporties menu window, clicked on the landscape format button, and chose to apply this setting for the highlighted text only. The result: All that is of course no big deal, and my page is flipped the 90 degrees as wished - but my header and footer break! They disappear from this page... and actually also from the next page (which is still upright portrait format), which is weird. And then the header and footer is back on the following pages again, though the page numbering restarts from 1. On this screenshot you can see that the previous and the following pages have headers and footers, but not the flipped one and not the page following the flipped one. What just happened here? How can I make the page numbering continue without restarting first of all, and then, how can I keep the header and footer on at least the upright page, that suddenly doesn't have them?

    Read the article

  • PostgreSQL failover cluster on Windows Server

    - by user36997
    We are looking for advice on how to setup a basic failover cluster for our application: We will be using 4 machines running Microsoft Windows Server (most probably 2003). All four will always run our application, which is essentially a web service. Load balancing is "outsourced" - somebody else handles the distribution of the web requests among the servers. Only one of the servers will be running the PostgreSQL server actively at any given time. Another server (of the four) also has the DB installed, but is on standby/passive. The DB data is stored on shared storage. No copying data between servers. Reads are done very frequently by many end-users, and in rather small chunks of data. Writes are done much less frequently, by less users, and in very large bulks of data. Now, how can one configure Microsoft Cluster Service to keep only one instance of the DB server and 4 instances (1 per server) of our application at all times? And does PostgreSQL integrate neatly with MSCS at all? Update: Instead of keeping the data on shared storage, I also consider using log shipping to replicate data on a couple of DB servers. There are two issues with this option: Log shipping only makes sure that I have a second server that gets all of the data and is ready to take over. How do I implement the actual failure detection and failover switch? Switching back: Suppose the master fails and the system automatically fails over to the slave, and later the master comes back online. I understand that with WAL shipping this will require to reconfigure the log shipping once again, and that switching back is far from seamless. Is that so?

    Read the article

  • MySQL Backup: Can I copying individual MyISAM table files to another server with different MySQL ver

    - by Komputer
    I means copying individual MyISAM table files is: (shut down mysqld and copy the .frm, .myd, and .myi files from one database folder to another) Question: (a) can I use this way to backup MySQL database folder from one server to another server with different MySQL version? (b) can this backup files moved to different OS? (example: debian to centos) thanks in advance.

    Read the article

  • How to configure VirtualBox server for performance at home

    - by BluJai
    I currently have two physical Ubuntu Server 10.10 servers at home: one serves as our firewall/router/DHCP/VPN server and the other performs double-duty as a file server and a VirtualBox host for an Ubuntu Desktop 10.10 machine which I use from remote connections (via NoMachine) for many thin-client purposes which are irrelevant to my question. What I'd like to accomplish is to consolidate the two physical machines into one which is a dedicated VirtualBox host (most likely running Ubuntu Server 10.10). Note that I'd like to stick with VirtualBox (if possible) because I'm most comfortable with it and use it on a daily basis at both home and work. Specifically, I plan to have one VM set up as file server, another as the firewall/router/DHCP/VPN (or possibly split those a bit) and a third, which is the only current VM (already VirtualBox), which is the thin-client host. My question comes down to performance and/or recommendations about the file server VM. The file server hosts about 6 terabytes of data across 4 drives. What I'd like to do is use raw disk access from the VM directly to the existing disks. However, I'm curious what performance advantage/disadvantage that would have as compared to using shared folders from the VM host and basically just have the whole drive served as a shared folder to the VM which would then serve it to the other machines on the network. I don't know if virtual disks would even work in this scenario and I certainly wouldn't want a drive to be filled with just a single file which is 1.5 TB (disk image). To add understanding of context, but not to get additional advice, I want to virtualize these machines because I intend to regularly use the snapshot capabilities of VirtualBox for the system disks (which will be virtual drives) of the VMs and I have some physical space/power needs to address (as I mentioned, this is at home).

    Read the article

  • Avoiding DNS timeouts when a dns server fails

    - by Neil Katin
    We have a small datacenter with about a hundred hosts pointing to 3 internal dns servers (bind 9). Our problem comes when one of the internal dns servers becomes unavailable. At that point all the clients that point to that server start performing very slowly. The problem seems to be that the stock linux resolver doesn't really have the concept of "failing over" to a different dns server. You can adjust the timeout and number of retries it uses, (and set rotate so it will work through the list), but no matter what settings one uses our services perform much more slowly if a primary dns server becomes unavailable. At the moment this is one of the largest sources of service disruptions for us. My ideal answer would be something like "RTFM: tweak /etc/resolv.conf like this...", but if that's an option I haven't seen it. I was wondering how other folks handled this issue? I can see 3 possible types of solutions: Use linux-ha/Pacemaker and failover ips (so the dns IP VIPs are "always" available). Alas, we don't have a good fencing infrastructure, and without fencing pacemaker doesn't work very well (in my experience Pacemaker lowers availability without fencing). Run a local dns server on each node, and have resolv.conf point to localhost. This would work, but it would give us a lot more services to monitor and manage. Run a local cache on each node. Folks seem to consider nscd "broken", but dnrd seems to have the right feature set: it marks dns servers as up or down, and won't use 'down' dns servers. Any-casting seems to work only at the ip routing level, and depends on route updates for server failure. Multi-casting seemed like it would be a perfect answer, but bind does not support broadcasting or multi-casting, and the docs I could find seem to suggest that multicast dns is more aimed at service discovery and auto-configuration rather than regular dns resolving. Am I missing an obvious solution?

    Read the article

< Previous Page | 556 557 558 559 560 561 562 563 564 565 566 567  | Next Page >