Search Results

Search found 21310 results on 853 pages for 'multiple domains'.

Page 57/853 | < Previous Page | 53 54 55 56 57 58 59 60 61 62 63 64  | Next Page >

• Triple-display setup using AMD drivers

  - by Halik

  I am currently running a dual display setup with nVidia 8800GTS video card, on a Ubuntu 12.10 box. The current setup uses nVidia TwinView to render the image on a 1920x1200 display and 1600x1200 one. I'm planning to add a third, 1280x1024 display to the setup. The change will require me to upgrade my GFX card to one supporting triple displays. I'll probably go with Sapphire Radeon 7770 (FLEX edition, to avoid additional active DP-DVI adapters). Before I invest in new GFX I wanted to ask - how well the AMD drivers will support such a setup. It does not matter whether it's fglrx or the OSS ones. If I remember correctly, when running Fedora on a Radeon x800, I had 'void' areas above and below the working area on my second display. The desktop was rendered in 1920+1280 width and 1200 height (which left 176px of vertical space accessible for my cursor and windows but not displayed on the screen - I'd prefer to avoid that). It may have very well been my misconfiguration back then. Generally, are there any solutions from AMD on par with TwinView? Or is it a non-issue at all? Also, I'm wondering about the usual stuff - hardware h264 decoding support, glitch-free flash support, any issues with Compiz/Unity?

  Read the article

• Second Monitor Detected, but not receiving a signal after upgrading to 12.04

  - by user62458

  After I upgraded to 12.04, my second monitor is detected (in display settings), but will not power on. I have scoured the Internet and forums for a solution and I can't find anything. I have found a couple people with the same problem, but never a solution for it. I am no expert, but I'm certainly not a noob. My computer uses AMD Radeon 6250 graphics, but I do NOT want to use the proprietary graphics drivers. They refuse to work properly with my second monitor (they ATI drivers will only mirror screens, and I've done everything to try to fix it, and I DON't want mirrored screens) Not to mention that the default open-source video drivers seem to work much better than the proprietary anyway! Again, Ubuntu's default video drivers work fine, and they even DETECT the second monitor (Dell 19'). I can drag stuff off the screen and put it on the 'space' of the second monitor and even a screen-shot shows that there are two monitors active; but the monitor is OFF. It will not power on. It goes into 'power-save' mode because it is not receiving a signal. For some reason it is not getting the signal to power on, even though Ubuntu thinks the monitor is working properly. I had this working fine on my Sony VAIO yesterday (with Radeon graphics/default Ubuntu video drivers). I upgraded to a Samsung Series 3 and now I have this issue. I can't for the life of me figure out why the monitor is connected, detected and I have screen space for the monitor, but the screen won't turn on! XRANDR Output: Screen 0: minimum 320 x 200, current 1366 x 768, maximum 8192 x 8192 VGA-0 connected (normal left inverted right x axis y axis) 1440x900 59.9 + 75.0 1280x1024 75.0 60.0 1152x864 75.0 1024x768 75.1 70.1 60.0 832x624 74.6 800x600 72.2 75.0 60.3 56.2 640x480 72.8 75.0 66.7 60.0 720x400 70.1 LVDS connected 1366x768+0+0 (normal left inverted right x axis y axis) 344mm x 194mm 1366x768 60.1*+ 1280x720 59.9 1152x768 59.8 1024x768 59.9 800x600 59.9 848x480 59.7 720x480 59.7 640x480 59.4 HDMI-0 disconnected (normal left inverted right x axis y axis)

  Read the article

• How do I set up a server for SSH?

  - by Rob S.

  At my workplace (a university) we have two Ubuntu servers. One is a teacher server and the other is a student server. I am currently setting up a new server to replace the existing teacher server. The new server is currently online and I am trying to get it setup so I can SSH into it from my home. Right now, I can SSH into the existing teacher or student server and then SSH into the new server. However, I can not SSH directly into the new server. What must I do so that I can SSH directly into the new server? Thank you very much in advance for your time.

  Read the article

• Disabling monitor reconfiguration when closing lid

  - by Tomas

  I often need to move my laptop from one working place to another. When I do this, there are two events Ubuntu responds to by changing the monitor set up: Removing/attaching the VGA cable Closing/opening the lid of the laptop While removing the VGA cable gives me what I need (single screen, highest native resolution on the external screen if connected; otherwise highest resolution on the laptop), the laptop close/open lid response is not as good. Every time I close or open the lid, Ubuntu reconfigures the monitor set up. When I close the lid now... the screen goes black for a few seconds and it switches to clone, with my laptop screen disabled. Reopening results in... briefly a black screen, then the external monitor being used as desktop extension. Ubuntu thinks too much. My first and foremost question: Is there any way to let Ubuntu ignore lid close events? Ideally (or when there's no way to solve above question) I'd want to change how it deals with the screen reconfiguration. Why does Ubuntu toggle the screen configuration between external, clone and single display? Can't I just configure it to always use the external monitor, when present, in single screen mode? Note that similar questions have been asked before (most notably this one), but these have been closed perhaps wrongly. Any ideas are very welcome, I don't mind playing around a bit to see if something works.

  Read the article

• How do I reset my display settings from the command line?

  - by Trevor

  I'm running 12.10 on a dell e5400 laptop and I used xrandr to get the dual monitors working that I connect through a laptop dock. I used xrandr again to switch back to the laptop display when I undocked. The problem is, after a restart, the laptop seems to want to come back up with the dual monitor configuration and the laptop screen stays blank. I can boot into single user mode but I'm not sure what to do from there to get the display settings reset. Any ideas? There's no xorg.conf file so I'm not sure where the settings are stored anymore. Thanks.

  Read the article

• Why is my Workspace switcher view skewed

  - by Lee

  I have been using Workspace switcher in Ubuntu just fine but recently have encountered this problem. The windows in the switcher don't fill the screen. I must have pressed some combination of buttons somehow but can't find any information anywhere in regards to resizing them. As you can see in the screen shot it looks like a perspective view or something. http://i1115.photobucket.com/albums/k553/lmt337/Screenshotfrom2012-07-04103519.png I should also add I have a dual monitor setup and nvidia graphics. The switcher still works but the fact the screens dont fit my actual screens is driving me nuts. Thanks in advance for any help.

  Read the article

• OpenGL ES multiple objects not being rendered

  - by ladiesMan217

  I am doing the following to render multiple balls move around the screen but only 1 ball is seen to appear and function. I don't know why the rest (count-1) balls are not being drawn public void onDrawFrame(GL10 gl) { // TODO Auto-generated method stub gl.glDisable(GL10.GL_DITHER); gl.glClear(GL10.GL_COLOR_BUFFER_BIT | GL10.GL_DEPTH_BUFFER_BIT); gl.glMatrixMode(GL10.GL_MODELVIEW); gl.glClientActiveTexture(DRAWING_CACHE_QUALITY_HIGH); gl.glLoadIdentity(); for(int i=0;i<mParticleSystem.getParticleCount();i++){ gl.glPushMatrix(); gl.glTranslatef(mParticleSystem.getPosX(i), mParticleSystem.getPosY(i), -3.0f); gl.glScalef(0.3f, 0.3f, 0.3f); gl.glColor4f(r.nextFloat(), r.nextFloat(), r.nextFloat(), 1); gl.glEnable(GL10.GL_TEXTURE_2D); mParticleSystem.getBall(i).draw(gl); gl.glPopMatrix(); } } Here is my void draw(GL10 gl) method public void draw(GL10 gl){ gl.glEnable(GL10.GL_CULL_FACE); gl.glEnable(GL10.GL_SMOOTH); gl.glEnable(GL10.GL_DEPTH_TEST); // gl.glTranslatef(0.2f, 0.2f, -3.0f); // gl.glScalef(size, size, 1.0f); gl.glVertexPointer(3, GL10.GL_FLOAT, 0, vertBuff); gl.glEnableClientState(GL10.GL_VERTEX_ARRAY); gl.glDrawArrays(GL10.GL_TRIANGLE_FAN, 0, points/2); gl.glDisableClientState(GL10.GL_VERTEX_ARRAY); }

  Read the article

• Ubuntu 12.10 - Dual monitors

  - by crazy coder

  I'm trying to set up a dual monitor with my laptop (Dell XPS L502X) and a monitor that I recently bought (Dell U2312HM). The cable are alright, because I tried this on Windows and all is fine. In Ubuntu 12.10 doesn't work. If I go to System Settings-Displays, button Detect Displays doesn't do anything. I may also say that I use Bumblebee, and my sudo nvidia-settings command only shows a windows with only nvidia-setting Configuration option.

  Read the article

• How can I extend the desktop onto an external monitor/projector?

  - by hellocatfood

  I've plugged in a projector into my laptop and I'm attempting to extend the desktop onto it (so that I can run a full screen app on the projector and have the controls on my laptop). I'm able to mirror the screens effectively (it does this by default) but I can't extend it. When I untick "Mirror screens" and press apply it asks me to log out and then back in again but it goes back to mirroring the screens. I'm able to extend desktop on to my external monitor at home, just not this projector. Is there a manual way or other way to do this other that through Monitors setting? My computer model is Dell Studio 1555: Pentium Dual Core T4300(2.1GHz,800MHz,1MB), 4096MB 800MHz DDR2 Dual Channel, 512 MB ATI Mobility RADEON HD 4570 using the ATI proprietary driver. My screen resolution is 1366x768 (16:9) The projector that it wont connect properly is a Hitachi CPX3. That page specifies that it's especially designed for projectors that use 16:10 aspect ratio, but considering my external monitor at home uses 4:3 should the differences in aspect ratio matter or be causing this error?

  Read the article

• Crash on shutdown when using second monitor

  - by plua

  I have recently added a second monitor to my setup. Instead of one VGA monitor, I now have one VGA and one DVI monitor hooked up to the computer. The displays work just fine. However, ever since this monitor was added Ubuntu (10.10) does not shut down properly. I go to shutdown and it starts shutting down but just hangs and I need to manually shut it down. This has been like this for weeks and I feel not comfortable shutting it down this way over and over again. Has anybody any idea what this can be? Or, also useful, does anybody know how to get some info on why this crash occurs? Any logs that can be used for this? Thanks! Paul

  Read the article

• Why when I log in my two screens shows the same image automatically?

  - by forellana

  When I log in on my computer, first my two monitors shows their own part of a larger desktop, then automatically changes to the same image on both screens, but I don't want to happen this, Is there any configuration to avoid this? About my hardware: 00:02.0 VGA compatible controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 09) 00:02.1 Display controller: Intel Corporation Mobile 4 Series Chipset Integrated Graphics Controller (rev 09)

  Read the article

• How to handle multiple pages of the same site with the same outlinks

  - by pandafromchina

  I am developing a back link tool for Chinese SEO (our web site URL is: http://link.aizhan.com just like ahrefs.com. I encountered a problem which is how to handle multiple pages of the same site with the same out links. For example: Most pages of bbs.chinaz.com have the same out links such as: bbs.chinaz.com/Tea/thread-6293993-1-1.html bbs.chinaz.com/Tea/list-1.html bbs.chinaz.com/alimama/thread-6265032-1-1.html bbs.chinaz.com/alimama/thread-6265032-2-1.html?userid=-1&extParms= bbs.chinaz.com/Shuiba/list-1.html bbs.chinaz.com/FeedBack/thread-4456753-1-1.html etc.. All of the pages have the same out links in the top of the page: www.cnzz.com(anchor text:????) www.313.com(????) www.idc123.com(????) Suppose I store these outlinks into database. The SEO will find there are six backlinks from bbs.chinaz.com of www.cnzz.com. This is obviously no sense for the SEO. Can you tell me how do you deal with this problem?

  Read the article

• Can't login to Unity 3d after enabling Xinerama for a short moment

  - by Amir Adar

  Today I connected a second monitor to my computer. I set it up using nVidia's control panel, and all was working quite well, so I figured it won't be a problem to try Xinerama, just to see the difference between that and twinview. After enabling Xinerama and restarting the X session, I saw that I was logged into a Unity 2d session. I thought it was a problem with Xinerama, so I switched back to twinview, but it still logged me into Unity 2d. I tried disconnecting the second monitor, no luck: still Unity 2d. I tried changing GPU drivers and installing drivers from a separate ppa, and still I was logged into Unity 2d. Up until this point, I didn't have any problem logging into Unity 3d. It only happened after I tried using Xinerama. I should note that I was doing all this while updates were going on in the background, so it could be something related to that, though I can't imagine what (I tried booting with another kernel, but no luck). So what exactly happened? Did changing the mode to Xinerama triggered some other changes that I'm not aware of? Did these updates cause a certain malfunction in the driver? Is it something else?

  Read the article

• Only one resolution available in Xorg.conf

  - by Kévin Guilbeault

  I recently upgraded to Ubuntu 12.10 and when I try to change my resolution in NVIDIA X server settings, I only get the native one (1600x900). When I had 12.04 installed, all resolutions were available in the drop down list. My goal is to have twinview working again. I used to set my two screens to twinview and clones, using my HDTV resolution (1360x768) which was previously available in 12.04 for my laptop screen too. In 12.10, I tried to install all of the NVIDIA drivers available except the nouveau driver. I tried to add a new mode using Xrandr --newmode / --addmode, but it didn't work; it coudn't detect my output. I'd like to know if this is a known bug and if there's something to do with that. Thanks!

  Read the article

• Monitor flickering ATI

  - by Atzu

  I'm using ubuntu 12.10 on laptop samsung with randeon hd 6620g (APU A8), when I run amdcccle -version it says 2.18, not sure if that's the correct version. My problem is that I have and external monitor, AOC e2343Fsk and when I finally got it working at the resolution I want 1920x1080 it works fine for like 5minutes and then it starts flickering... I solved this on Windows (the exact same problem) with some options (I don't remember very well) I believe there were some buttons '+' and '-' on some vsync option I played with them on windows and Yay! got it working, but I don't see anything similar on this catalyst version (I used xorg-edgers ppa for installing fglrx). Thanks.

  Read the article

• How to drag widgets from monitor to monitor in kubuntu?

  - by Mien

  I have Kubuntu 12.04 on my Dell Inspiron. I use an extern monitor as my default one, and my laptop monitor as my second monitor. I can place widgets on the extern (default) screen, but when I drag them to the laptop (second) screen, they disappear. I can put widgets on the second screen, if I open the widget screen on that screen, but I can't drag them to my first monitor. How can I switch between monitors for the widgets?

  Read the article

• Sys.WebForms.PageRequestManagerServerErrorException: An entity object cannot be referenced by multiple instances of IEntityChangeTracker [closed]

  - by Mingebag

  `Story: I have a strange error when I try to save something I got this error message An entity object cannot be referenced by multiple instances of IEntityChangeTracker. I really don’t know what that is and why is it appear, it appears only when I try to save something my insert and update is working, only when I try to save something in db from my Telerik grid if (this.annualVacationList != null) { List<AnnualVacation> vacationToSave = this.annualVacationList; IEnumerable<AnnualVacation> existing = paramUser.AnnualVacations; foreach (AnnualVacation toSave in vacationToSave) { AnnualVacation existingItem = existing.Where(x => x.AnnualVacationId == toSave.AnnualVacationId).SingleOrDefault(); if (existingItem == null) { ctx.AddToAnnualVacations(toSave); } else { existingItem.FromDate = toSave.FromDate; existingItem.ToDate = toSave.ToDate; existingItem.WorkingTime = toSave.WorkingTime; existingItem.VacationDays = toSave.VacationDays; } } } ctx.SaveChanges(); } After debugging I have seen that the code brake down in the Project.Name.Designer.cs ..... O.o public void AddToAnnualVacations(AnnualVacation annualVacation) { base.AddObject("AnnualVacations", annualVacation); }

  Read the article

• Dual monitor display 12.04?

  - by MrMonty

  I have 2 beautiful 27" asus monitors. I started trying out Ubuntu 12.04 and now only one works and thats vga .. Any help here cause I'm stumped. I have a bfg tech nivida Geforce 8800 gt 512mb and I'm trying to fix this. Getting this error Wen i try to configure the xorg file Failed to set MetaMode (1) 'DFP-0: 1280x1024 @1280x1024 +0+0, DFP-1: 1280x1024 @1280x1024 +1280+0' (Mode 2560x1024, id: 50) on X screen 0. ........................................................................................... This is the xorg.conf ....................................................... nvidia-settings: X configuration file generated by nvidia-settings nvidia-settings: version 295.33 (buildd@allspice) Fri Mar 30 15:25:24 UTC 2012 Section "ServerLayout" Removed Option "Xinerama" "1" Removed Option "Xinerama" "0" Removed Option "Xinerama" "1" Identifier "Layout0" Screen 0 "Screen0" 0 0 InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" Option "Xinerama" "0" EndSection Section "Files" EndSection Section "InputClass" Identifier "Mouse Remap" MatchProduct "Saitek Cyborg R.A.T.7 Mouse" MatchDevicePath "/dev/input/event*" Option "ButtonMapping" "1 2 3 4 5 6 7 8 9 0 0 0 0 0 0" EndSection Section "InputDevice" # generated from default Identifier "Keyboard0" Driver "kbd" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor1" VendorName "Unknown" ModelName "Ancor Communications Inc VE247" HorizSync 30.0 - 83.0 VertRefresh 50.0 - 76.0 Option "DPMS" EndSection Section "Monitor" # HorizSync source: edid, VertRefresh source: edid Identifier "Monitor0" VendorName "Unknown" ModelName "Ancor Communications Inc VE247" HorizSync 30.0 - 83.0 VertRefresh 50.0 - 76.0 Option "DPMS" EndSection Section "Device" Identifier "Device1" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "Quadro FX 1500" BusID "PCI:1:0:0" Screen 1 EndSection Section "Device" Identifier "Device0" Driver "nvidia" VendorName "NVIDIA Corporation" BoardName "Quadro FX 1500" EndSection Section "Screen" Identifier "Screen1" Device "Device1" Monitor "Monitor1" DefaultDepth 24 Option "TwinView" "0" Option "TwinViewXineramaInfoOrder" "DFP-1" Option "metamodes" "DFP-1: 1280x1024 +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Screen" Removed Option "TwinView" "0" Removed Option "metamodes" "DFP-0: 1280x1024 +0+0" Removed Option "TwinView" "1" Removed Option "metamodes" "DFP-0: 1280x1024 +0+0, DFP-1: 1280x1024 +1280+0" Removed Option "TwinView" "0" Removed Option "metamodes" "DFP-0: 1280x1024 +0+0" Identifier "Screen0" Device "Device0" Monitor "Monitor0" DefaultDepth 24 Option "TwinView" "1" Option "TwinViewXineramaInfoOrder" "DFP-0" Option "metamodes" "DFP-0: 1280x1024 +0+0, DFP-1: 1280x1024 +1280+0; DFP-1: 1280x1024_60 +0+0" SubSection "Display" Depth 24 EndSubSection EndSection Section "Extensions" Option "Composite" "Disable" EndSection FILE ^^^^

  Read the article

• How to configure screens in console or create screen configuration profiles?

  - by uncle Lem

  I have two monitors and integrated GPU (Intel® HD Graphics 4600). It works fine for work or movies, but if I launch games in fullscreen mode - I get artifacts, glitches and so on. Temporary disabling second monitor solve this problem, but then I have to enable it back, and set its properties manually (by default, additional screen attaches its left-top corner to main monitor's right-top corner, but I need it to be left-bottom and right-bottom corners). So I need some kind of automatization here. Best option - tool to create and swap between some kind of config profiles. Or, maybe, some console manipulations which I can put into script files would be fine too. (Ubuntu 13.04, if it matters)

  Read the article

• How can I stop the panel from showing on an external projector/monitor?

  - by hellocatfood

  In Ubuntu 10.10 (and possibly previous versions), when I connected my laptop to an external source (monitor/projector) and set it not to clone my desktop the display on the external source would not show the (gnome-)panel (just a full-screen desktop with no icons). Since upgrading to Ubuntu 11.04 (using Unity) when I now connect the external source has the panel on there. Is there any way to revert to the previous behaviour in 11.04?

  Read the article

• How do I get HDMI output working on a Dell XPS 15 L502x?

  - by Jones

  Recently I've bought my dream's notebook, a Dell XPS 15 but since then this dream became a kind of endless nightmare. I'm almost getting crazy to make my graphic card driver work properly, but it seems to be just impossible. Yes, I have a 2GB NVIDIA GeForce GT 540m (Optimus) in it! It simply doesn't work. Every time I generate the xorg.conf Ubuntu hangs on while starting up, which forces me to remove this file to be able to start the notebook with the standard graphic settings. Another problem is that the Dell XPS 15 does NOT have a VGA output, but a HDMI. So, to be able to use a second monitor I have to configure it by the NVIDIA X Server Settings, which just works if the driver is properly initialized with the xorg.conf. I've also tried to make it work with the Bumblebee, but unfortunately it didn't help me much with the HDMI output. Do you guys have any idea to solve this deadlock? Is there any way for me to use my second monitor?

  Read the article

• Ubuntu Unity (64-bit) Bugs on Nvidia dual screen [closed]

  - by Kristofer

  On my work computer I have upgraded 10.04 to 10.10 and now to 11.04. Upgrades have mostly worked well and the dual screen setup is almost working. There are however a couple of annoying bugs which I tried to report but the bug reporting tool told me to ask about the bugs here. Here's what I have found: Auto-hide stops working. It doesn't seem to matter which application is maximised/covering the dock, it just stays on top. I have tested changing the autohide settings with no result. Scenario: One maximised window on each screen. If I now try to drag the window that doesn't have focus by dragging the top of the window nothing happens. I can also not give the window focus by clicking the top bar, I have to click inside the window and then I can drag the window. If I unmaximise the window with focus it does work and I can both change focus and drag the window directly by clicking the top of the maximised window. Any bug fixes coming for these issues? Any work-arounds?

  Read the article

• How do I turn off the laptop screen while using an external monitor?

  - by jpmelos

  When I close my laptop lid, all my screens are turned off (my laptop screen and my LG M237WA monitor). I'd like to know how do I make it turn off only the laptop screen and keep the monitor on (I want that behaviour for when I want to watch a movie on my monitor and don't want any brightness coming for the laptop screen). I'm using a HP Pavilion dv4-1290br, which comes with a nVidia GeForce 8400M GTS. I'm using the nVidia driver and it's working perfectly. For my X settings, I'm using TwinView, my laptop is set to 1280x800 and my monitor to 1920x1080. I hope you guys can help me, for I couldn't find anything so far. Thank you very much.

  Read the article

• Connecting two monitors at the corners

  - by fastmultiplication

  I am using two separate X screens on two monitors and I would like them to be connected at the lower right corner. That is, if you move to the lower right corner of screen0 the mouse should appear at the upper left of screen1. I do not want an entire edge of each monitor to be permeable to the mouse. I modified the xorg.conf file like so: Section "ServerLayout" Identifier "Layout0" Screen 0 "Screen0" 0 0 Screen 1 "Screen1" Relative "Screen0" 1200 1000 InputDevice "Keyboard0" "CoreKeyboard" InputDevice "Mouse0" "CorePointer" EndSection (screen 0's resolution is 1280x1024) so there is a bit of overlap. However whenever I move the mouse to the bottom of screen0, the pointer appears at the upper left of screen1. And, the entire top of screen1 is permeable to the mouse and brings it to the lower left corner of screen0. I have tried various numbers in following the "relative" statement - if I put 1280 1024 the mouse does not cross over at all. If I use 1280 1023 the entire right side of screen0 is permeable. I haven't been able to find any documentation about how to explicitly tell the mouse where to crossover - is there some? It seems that xorg is being really aggressive in guessing where the mouse crossover should take place. Does anyone know how to do this? Thanks!

  Read the article

• Dual displays not working with Xinerama in Ubuntu 12.04

  - by user68489

  I just upgraded from Ubuntu 10.10 to 12.04. I had been using a display configuration just like the one described at http://bitkickers.blogspot.com/2009/08/rotate-just-one-monitor-with.html without any problems under 10.10. I have an nvidia Quadro FX 380 and have upgraded to the latest drivers (295.49). Everything appears to be fine when the system first boots up. However, after logging in, the left screen goes black, and the right screen displays what should be displayed on the left screen. Logging into Ubuntu 2D somewhat improves things. The left screen correctly displays the left portion of the desktop but the right screen contains a duplicate view of the left screen. Turning off Xinerama and enabling TwinView appears to fix the issues but does not allow the right monitor to be rotated. Since the display problems start to occur only after logging on, I thought it might have to do with carryover user configuration from 10.10 but the problems persist even when logging in as a guest. Clicking on System Settings - Displays results in the error message "Could not get screen information - RANDR extension is not present." Any help would be greatly appreciated.

  Read the article

< Previous Page | 53 54 55 56 57 58 59 60 61 62 63 64  | Next Page >