Search Results

Search found 21945 results on 878 pages for 'online services'.

Page 572/878 | < Previous Page | 568 569 570 571 572 573 574 575 576 577 578 579  | Next Page >

• How long do managed gigabit ethernet switches take to boot up?

  - by Warren P

  One critical drawback that I have found in researching managed-switches, and one that I have some past experience with is that anything with "lots" of firmware is going to have lots of issues associated with that firmware. We are in the middle of researching rackmount gigabit switches (48 port). It looks like for 48 ports, our only choice is managed switches (Dell, Cisco/Linksys,HP, etc). What I want to know, that I can not find out much about is the boot-time for various managed switches. If you own one, can you please answer with the model number, and the cold boot time in seconds. I have read online that Linksys (now Cisco) SRW series sometimes take almost 5 minutes before they are fully booted up, and that is an unacceptable cost for us. I particularly want to know about Dell PowerConnect managed switch bootup time (model 3548 and 5448), and would like to confirm the 5-minute boot time on the SRW2048 or similar model, and any HP ProCurve boot up times. The composite of all those figures ought to form an interesting overall performance picture.

  Read the article

• inetmgr missing after vista iis7 install

  - by GHarping

  I have installed IIS7 on Vista with all options from Programs and Features->Turn on/off windows features. I have searched for inetmgr accross the whole system with no luck. It is also not present in C:\Windows\System32\inetsrv. The IIS Admin Service is shown as running in the list of all services. Might anyone know what the problem is? My initial problem before this was that after installing IIS and trying to view any arbitrary page via localhost/*filename*, i recieved the error HTTP Error 404.4 - Not Found The resource you are looking for does not have a handler associated with it.

  Read the article

• set all apache sites offline with temporary static cached original pages

  - by rubo77

  I would like to set all virtualhosts on my server down for maintenance for some time. The temporary page should contain something like sorry, the page www.xxx.com is down for maintenance. you can see the cached version here: Then the trick: the user should then see the cached page from a cache like googlecache or similar for the requested page as long as the server is down. This would show the correct content on pages, that are static anyway and give the visitor the needed content in many cases, while I can shut down mysql and other services that would usually be needed to show that pages. How can I set a global page on all virtualhosts, that parses the original requested URL through PHP?

  Read the article

• Unable to connect guest using VMWare Player

  - by eLAN

  I'm running RedHat server 5.3 as guest on Window XP VMware palyer. the network setting is set to "Host Only", but I have tries all other settings. I'm able to ping the guest machine, but I'm unable to connect it in any other way including webserver, Tomcat, Telnet, ssh. all of the services above are working from within the guest (using localhost). Guest firewall and SELinux are disabled. any idea on what I should check next? every idea will be appreciated... thnaks Ilan

  Read the article

• Kill xserver from command line (init 3/5 does not work)

  - by John Smith

  Hi, I'm running Linux Mint 10, although I've had this same issue with other variants of Linux. I've been told/found while researching that if the X server hangs or otherwise errors, one can drop to a root prompt, usually at another tty, and execute init 3 (to drop to single user mode) and then init 5 to return to the default, graphical session. Needless to say, I've tried this before in multiple configurations on multiple machines to no avail. The only feedback I receive form executing those two commands is a listing of VMWare services (from a kernel module) that are stopped and then restarted. Note: If I run startx (either before or after init 3), then I am told that the xserver is still running and that I should remove /tmp/.X0-lock. Having tried that, it removes that error message, but claims that the xserver cannot be attached as another instance is running. How do I kill the xserver completely? Can I killall some process name?

  Read the article

• Why is my hosts file not working?

  - by elliot100

  I've been using the hosts file to for local website development, and it's recently stopped working. No entries other than localhost resolve. I've simplified to test, so it now contains only 127.0.0.1 localhost ::1 localhost 127.0.0.1 test.dev localhost responds to ping, test.dev does not. The file is called hosts with no extension It has no trailing spaces It's saved in C:\WINDOWS\System32\drivers\etc which matches the value of HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Services\Tcpip\Parameters\DataBasePath Oddly, despite UAC being on, I can edit, delete and save the file without admin permissions No proxy is being used, PC is not connected to network for testing Stopping the DNS Client service seemed to resolve the issue for a few minutes, test.dev briefly resolved but doesn't any more. Only firewall is Windows' Machine has been restarted. Is there anything else I should try?

  Read the article

• SharePoint Designer prompts for credentials when edited from IE8

  - by Rob Nicholson

  Our intranet is hosted using the free SharePoint services on Windows 2003. Consider the following page: http://vserver003/help/technology/multimedia/multimedia.htm On selecting "Edit with Microsoft Office SharePoint Designer" from IE8, SPD launches, opens the website and then the selected page - all is well. In order to make moving the intranet easier, we've set-up a DNS setting called intranet.company.local so you can also access the intranet that way: http://intranet.company.local/help/technology/multimedia/multimedia.htm However, when you edit this page, SPD designer prompts you for credential, i.e. domain\username and password. If you enter the details it opens fine. If you don't enter the details, the page still opens but not the website. Any ideas have to get around this prompt? Haven't a clue where to start looking. Thanks, Rob. PS. The same prompt occurs if you use the physical IP address.

  Read the article

• How to migrate exchange 2007 (sherweb) to Google Apps?

  - by Yoffe

  I need to migrate our Sherweb.com exchange 2007 services to a Google Apps account. For the process I am really not sure.. I understand I should start with creating aliases for all email accounts within the exchange server, in Google Apps, and here I'm not sure how am I supposed to explain the Exchange that the DNS have changed without losing emails.'' Second thing is: How can I safely move the up-to 3GB mailboxes from the Exchange server to the new Google Apps accounts? Must it be with Outlook data files? If so, how do I actually upload the data files into the Google Apps account? And if not, what would be a proper way to do so? Would really appreciate any kind of help.

  Read the article

• Squid Proxy Server: limit total bandwidth

  - by Pitto

  Hello my dear friends! We have a marvellous squid proxy with dansguardian for filetering and they both work just great. Is there any easy way to limit the total bandwidth usage? I'd like to set the max amount of squid users internet use to 1200 since our total band is 2000 and I need the rest to ensure other services such as voip to work without hiccups related to huge downloads on the "internet side" of our connection and similar issues. I mean a total squid bandwidth limitation and not a user-based. Fair thanks to everybody.

  Read the article

• Server 2012 Storage Pools, Raid Controller... can the Storage Pool deal with it?

  - by TomTom

  Before trying it out - I don't find any documentation. Given that Storage Pools have serious performance problems with parity, and do not rebalance data at the moment when you add discs, my preferred way to use them would be as think provisioned space, ISCSI targets - with every "Pool" running against 1 RAID that comes from a Raid controller (who also introduces SSD read and write caching - another thing missing from Storage Pools). The main question is - how does a Storage Pool handle the change in the underlying disc that can happen? I mostly talk about OCE (Online Capacity Expansion), where a disc after an expansion suddenly reports a larger space. Standard Windows allows you to use this additional space (and expand the partitions). How does a storage pool handle it?

  Read the article

• How can I receive more traffic? My VPS fails!!!

  - by Vic

  I have a web site - photo gallery. About 400 photos. Site on Gallery 3. mySQL. Hosted on VPS from myhosting.com (CPU 1792 MHz, 2048 MB RAM). Everything seems to be ok, but there is one big problem. Once traffic reaches ~ 20 people (online) - website start loading really really slow. Actually website can't be loaded about 30-60 sec. What should I do? Buy more RAM / CPU on the same VPS? Move to a dedicated server or maybe myhosting.com just sucks? What do you recommend?

  Read the article

• Dovecot immediately logs off user

  - by nona urbiz

  I'm trying to set up email on my server, and have successfully set up POP3 with gmail for my main account. When attempting to set up another user though, gmail reports ` There was a problem communicating with dylanstestserver.com. I can't figure out why it's working for me and not the other users. I do receive email sent to the address on the server. One suggestion I found online was to try logging in over telnet, but strangely, it kicks me off right after I log in. dylan~$ telnet dylanstestserver.com 110 Trying 50.16.219.8... Connected to dylanstestserver.com. Escape character is '^]'. +OK Dovecot ready. user dylanstestemail +OK pass password +OK Logged in. Connection closed by foreign host. thanks for any ideas and help

  Read the article

• How can I change my mysql user that has all privileges on a database to only have select privileges on one specific table?

  - by Glenn

  I gave my mysql user the "GRANT ALL PRIVILEGES ON database_name.* to my_user@localhost" treatment. Now I would like to be more granular, starting with lowering privileges on a specific table. I am hoping mysql has or can be set to follow a "least amount of privileges" policy, so I can keep the current setup and lower it for the one table. But I have not seen anything like this in the docs or online. Other than removing the DB level grant and re-granting on a table level, is there a way to get the same result by adding another rule?

  Read the article

• Finding proof of server being compromised by Black Hole Toolkit exploit

  - by cosmicsafari

  I recently took over maintenance of a company server. (Just Host, C Panel, Linux server), theres a tonne of websites on it which i know nothing about. It had came to my attention that a client had attempted to access one of the websites hosted on this server and was met with a warning from windows defender. It had blocked access because it said the website had been compromised by the Black Hole Toolkit or something to that effect. Anyway I went in and updated various plugins and deleted some old suspect websites. I have since ran the website in question through a few online malware scanners and its comes up clean everytime. However im not convinced. Do any of you guys know extensive ways i can check that the server isn't still compromised. I have no way to install any malware scanners or anti virus programs on the server as it is horribly locked down by Just Host.

  Read the article

• Outlook 2007 disconnecting after sending email to specific email

  - by Michael

  So when a user emails another tech in my domain they get the prompt for username/password as though they got disconnected. I have not seen any issues in the event logs, tried deleting the email address from his auto correct, ran Outlook in safe mode and searched online as well. I am kind of lost. Checked the event logs on the exchange server as well in the security and still nothing. Exchange 2010, Client OS: Vista x64, Outlook 2007. Thanks!

  Read the article

• Configuring BIND to use VM's DNS for specific domain

  - by Srirangan

  I work on a project for which I use an Ubuntu server vm on an Ubuntu host. The VM runs all the services / webapps through haproxy and nginx and serves it on the domain (xyz.com). I manually modify my resolv.conf to use the VMs IP address as the nameserver and I can run my app on the host browser. The problem is I am modifying an auto-generated file (resolv.conf) and I need to do it each time. Is there a smart way to say: -- are you accessing xyz.com? -- if yes use VM's DNS server, else use the hosts

  Read the article

• Time difference between servers after disaster recovery

  - by Sandokan

  We are running an old training system based on Windows Server 2003 and XP-clients. The solution is rather simple with four servers, two of them beeing DC:s. Everything is preconfigured and that goes for backup scheme as well. The backup software is Symantec BackupExec 2010. The scheme is a standard GF-F-S routine with full backups running once a week on Sundays. The other six days run differential backups. Now let's say in a worst case scenario, a server crashes on Saturday and we have to restore it from backup. The last backup will then be six days old and thus it will come online with six days old configurations. Will this pose a problem for the other servers or will the recovered server "get in line" eventually?

  Read the article

• Browsing not working in Windows 8

  - by Jonathan Perry

  I'm using Windows 8 Professional installed on Windows 7 using the "Save my preferences and apps" installation option. The Windows works great, apps are downloading and I can listen to online radio stations using the TuneIn radio app meaning the internet connection is alive, however, when I open a browser (either Chrome or IE10) and try to browse the internet, I'm getting an "Unable to resolve DNS" error message. Prior to installing the internet browsing worked flawlessly I must say. I'm using ESET NOD32 Antivirus so I suspect that it might interfere with the web connection now, but I'm not so sure. Internet options show that the PC is set to resolve the DNS automatically. I don't know what to do. My other Win7 PCs in my wifi home network are connecting to the internet without any issues. If anyone can help me resolve this I'll be grateful :) Thanks

  Read the article

• Installing Wordpress - constant PHP/MySQL extension appears missing

  - by Driss Zouak

  I've got Win2003 w/IIS6, PHP 5 and MySQL installed. I can confirm PHP is installed correctly because I have a testMe.php that runs properly. When I run the Wordpress setup, I get informed that Your PHP installation appears to be missing the MySQL extension which is required by WordPress. But in my PHP.ini in the DYNAMIC EXTENSIONS section I have extension=php_mysql.dll extension=php_mysqli.dll I verified that mysql.dll and libmysql.dll are both in my PHP directory. I copied my libmysql.dll to the C:\Windows\System32 directory. When I try to run the initial setup for WordPress, I get this answer. I've Googled setting this up, and everything comes down to the above. I'm missing something, but none of the instructions that I've found online seem to cover whatever that is.

  Read the article

• How to archive Exchange mailboxes remotely?

  - by amyassin

  We have an environment that is based on an Active Directory domain (running Windows Server 2003 SP2), an internal email system using Exchange Server 2003 (internal mailbox, nothing online), and the clients run a mixture of MS Outlook 2007&2010, with the majority running 2007. Recently we noticed that Exchange server is taking so much space for mailboxes. We are examining some solutions to reduce space, and it seems that we could make use of the archiving feature to archive older messages. I can set the auto-archive option manually for every individual user, but is there any other easier way to automate that task? Is there any feature in exchange server or active directory domain that enables setting that as a kind of policy or something similar, or a script to be scheduled to run by all users?

  Read the article

• Is there any way to limit my Internet connection to a per program basis?

  - by Igoru

  My Linux connection is REALLY free. I live in Brazil, so where I live I can only have 1 Mbit/s. Yes I know it's sad, but it's not the point. Everytime I'm updating my Ubuntu 9.04 or downloading something, it does eat all my bandwidth. Like, while update-manager is downloading the packages, I can see by netspeed applet in my panel that the incoming traffic goes to 110 kB/s. And then, my Emesene suddenly goes disconnected, and I can't navigate. As you can imagine, I can't use my Internet connection again until the packages are all downloaded or I cancel the update in the middle. As I said, same thing happens when I'm dowloading something, but less intrusive and immediate. The question is: is there any way to limit that APT/downloads traffic to some way I can still use my other Internet services, or to reserve some bandwidth for common navigation tasks (like we have on Windows, but I forgot this thing's name, it's like "something packages".

  Read the article

• Technicolor TG582n with external DHCP server [on hold]

  - by Jack

  We have a small home setup with a Technicolor TG582n on Plusnet ISP. We have a Samba4 DC with DNS forwarding enabled. The DC forwards to the Technicolor. However, the client machines have their DNS settings manually set. This is an annoyance when using laptops on other networks. We would like to have DHCP handled on the server machine, such that when a client connects to the Technicolor, it gets its IP and DNS information from the DHCP server, eliminating the need to manually set adapter DNS settings. However, I cannot find an option to disable DHCP on the Technicolor and am not completely clear on how one would point DHCP services to the server from the Technicolor if there were the option. So, how would one make the Technicolor use an external server for DHCP leases?

  Read the article

• System Restore Points

  - by Ross Lordon

  Currently I am investigating how to schedule an automatic initiation of a system restore point for all of the workstations in my office. It seems that Task Scheduler already has some nice defaults (screenshots below). Even the history for this task verifies that it is running successfully. However, when I go to Recovery in the Control Panel it only lists the System Restore Points one for every previous for only 3 weeks back even if I check the show more restore points box. Why don't the additional ones appear? Would there be a better way to implement a solution, like via group policy or a script? Is there any documentation on this online? I've been having a hard time tracking anything down except how to subvert group policy disabling this feature.

  Read the article

• Open a screen session inside a certain user on boot Ubuntu Server Linux

  - by Pez Cuckow

  I currently have a private server which I test my web apps on which runs Ubuntu Server 10.04 I also host a few game servers (rather than having wasted CPU time :-D) for some of my friends. These game servers I run in the game user account and each one has it's own screen session (so friends can ssh in and reboot the game server etc...). For example screen -R l4d2 runs ./start in the L4D2 folder. However if I reboot the server (which I have to do occasionally) all these sessions close and I have to manually create all the screen sessions and run the required games within them. Is there a way to set these screen sessions as Daemons or services or just boot on server start so they restart themselves on server reboot? I hope I have made my question easy to understand but feel free to ask questions! Many thanks,

  Read the article

• Google Drive desktop client not updating existing files from other users

  - by cqm

  I've looked around and there doesn't really seem to be any troubleshooting information for the Google Drive desktop client. It all assumes you are using Google Docs on the web. Anyway, my team is trying to use Google Drive like Dropbox, where multiple people are editing files shared amongst them through the desktop, such as images. Dropbox is really good at noticing when a checksum for a file is changed, and syncing it. Google Drive's desktop client seems not to do this at all. Google Drive desktop client seems to only sync newly created files and not giving any notification at all that there is a modified version, it will never sync it, even though going online and opening that file will show the modified version. Is there any way to fix this? and the answer has nothing to do with proxy or firewall configurations. Team is using computers running OSX and Windows.

  Read the article

< Previous Page | 568 569 570 571 572 573 574 575 576 577 578 579  | Next Page >