Search Results

Search found 17374 results on 695 pages for 'option strict'.

Page 573/695 | < Previous Page | 569 570 571 572 573 574 575 576 577 578 579 580  | Next Page >

• Windows 7 not booting after failed SRT (SSD caching) install

  - by david

  This is a fairly new computer, only about a month old. i7 2700k, z68 motherboard, with a 1.5tb WD black HD, and a 128gb crucial M4 ssd. I followed the instructions for setting up ssd caching, the SATA controller was set to RAID, I installed the intel software and enabled acceleration and it said everything went fine. But when I went to reboot, I received the lovely "Reboot and Select proper Boot device" error message. I checked the bios, and it was booting from the correct HD (I tried the only other option anyway just in case, it was the ~50 odd gb of unformatted space left on the SSD) AFter that I entered the raid until (ctrl-i at boot) and removed the acceleration and deleted the raid array (because it was being used as a cache this was non destructive) Still no boot. So I reinstalled win7 directly on the SSD, booted, and checked the HDD to make sure it hadn't been wiped. It hadn't, all the files were still there, including all the windows stuff. I backed up my data to an external drive just in case, but I'd really like to get this install booting again. I trawled the webs a bit, and have tried entering recovery mode and using the bootrec.exe and bootsect.exe to fix it, but to be honest I'm not sure what I'm doing with those. My question is basically: How do I make my harddrive bootable again?

  Read the article

• Linux: Encryption of a physical LVM volume doesn't imply encryption of its logical subvolumes?

  - by java.is.for.desktop

  Hello, everyone! I installed OpenSuse one year ago on my notebook. I created all partitions except /boot inside an LVM partition. I enabled encryption for it during setup. The system asked me a password on each boot later. Everything seemed fine... But one day I wanted to cancel the boot process and did it with SysRq REISUB. During entering this combination, the system suddenly continued to boot without any password being entered. I had no /home and no swap, but / was mounted! I checked multiple times, it was inside an "encrypted" physical LVM volume. Later I found out that OpenSuse can't encrypt / at all. There is an option to enable encryption for each logical volume, and indeed it fails for /. Later I tried Fedora. The options during partitioning were misleading by same means. I could enable "encryption" of a physical volume and each logical subvolume. With the exception that Fedora actually allowed to encrypt /. Question: What's the point of setting up "encryption" for a physical LVM volume, when it doesn't imply (real) encryption of its logical subvolumes? Did I get something wrong in this whole concept?

  Read the article

• PST backup with Volume Shadow Copy Service

  - by NoMadMan

  I was asked to implement the task of backing up 35 PST files ranging from 800Mb to 2000Mb. Windows XP and Windows 2000 workstations are assigned to the users and we have a Windows 2000 domain controller we use to back up files on 3x 500Gb external hard drives. I found several methods from applications to scripts. Local or remote applications would be my last resort. I came across this script based on Volume Shadow Copy Service. CopyWithVss I wanted to know if there would be a problem if the path had spaces. Would mounting the destination path of each PST folder with a drive letter be more practical? My concern with mounting option is that i would eventually run out of letters since I have 35 and possibly more workstations to back up. Lastly, can someone give me an example of CopyWithVss if it were run on a production network? The script is a bit cryptic even after reading several times. Where in the script do I enter the source and the destination? I'm a Mac user so please excuse my ignorance with Windows platform.

  Read the article

• Windows Server 2003 IPSec Tunnel Connected, But Not Working (Possibly NAT/RRAS Related)

  - by Kevinoid

  Configuration I have setup a "raw" IPSec tunnel between a Windows Server 2003 (SBS) machine and a Netgear FVG318 according to the instructions in Microsoft KB816514. The configuration is as follows (using the same conventions as the article): NetA | SBS2003 | FVG318 | NetB 10.0.0.0/24 | 216.x.x.x | 69.y.y.y | 10.0.254.0/24 Both the Main Mode and Quick Mode Security Associations are successfully completed and appear in the IP Security Monitor. I am also able to ping the SBS2003 server on its private address from any computer on NetB. The Problem Any traffic sent from a computer on NetA to NetB, or from SBS2003 to NetB (excluding ICMP Ping responses), is sent out on the public network interface outside the IPSec tunnel (no encryption or header authentication, as if the tunnel were not there). Pings sent from a computer on NetB to a computer on NetA successfully reach computers on NetA, but the responses are silently discarded by SBS2003 (they do not go out in the clear and do not generate any encrypted traffic). Possible Solutions Incorrect Configuration I could have mistyped something, somewhere, or KB816514 could be incorrect in some way. I have tried very hard to eliminate the first option. Have re-created the configuration several times, tried tweaking and adjusting all the settings I could without success (most prevent the SA from being established). NAT/RRAS I have seen multiple posts elsewhere suggesting that this could be due to interaction between NAT and the IPSec filters. Possibly the NetA private addresses get rewritten to 216.x.x.x before being compared with the Quick Mode IPSec filters and don't get tunneled because of the mismatch. In fact, The Cable Guy article from June 2005 "TCP/IP Packet Processing Paths" suggests that this is the case, (see step 2 and 4 of the Transit Traffic path). If this is the case, is there a way to exclude NetA-NetB traffic from NAT? Any thoughts, ideas, suggestions, and/or comments are appreciated.

  Read the article

• System With Two Network Adapters [closed]

  - by Synetech inc.

  Hi, My system has a NIC (Marvell Yukon) built-into the motherboard, but I also have a D-Link (RealTek) card. I figure that using the D-Link and disabling the Marvell makes the most sense, though I'm wondering if maybe the built-in one has better throughput (not that my Internet connection is so fast). Also, I'm wondering about the merits of using both at the same time. My router has four ports and I have experimented with enabling and plugging both NICs into the router. I was able to connect to the Internet, but the pattern of usage seemed irregular (which adapter was chosen for the transfer and any given point). I also considered bridging the two, but am having difficulty in finding out what exactly creating network bridge does in the context of the Windows Network Connections window. I am familiar with the concept of connecting networks, so it seems to me that birding two connections on the same segment is pointless at best (and can cause problems like loops?) Does anyone have any tips on what to do if a system has more than one NIC and any clarification on the bridge option? Thanks a lot.

  Read the article

• How can I create a macro that acts on a relative reference rather than an absolute reference to cell A1?

  - by Bruce

  I have a master rent statement in an Excel 2007 (macro enabled) spreadsheet that shows all tenants in rows with columns formed by the months. Each tenant then has a separate rent statement sheet like the one below that pulls the data through from the master rent statement and all I do then is to copy the last 4 columns to the right and add them to the right, just renaming the month labelled as ‘rent due’ with the current month and then hiding the previous last 4 columns to the left so that the statement always shows the previous month's activity and the amount due for the current month: I used a macro to speed up the creation of these statements, but then found that in some cases the result was wrong and needed major correction because the macro use absolute references i.e. its starting position was relative to cell A1 whereas some of my rent worksheets commence from a different column and in some cases from a different column and a different row. I have tried recording the macro with 'Use relative references' but when trying to use the macro it only gets part way through its operation before it stops and the message appears: Run time error '1004' Application defined or object defined error with the option to End or Debug or go to Help and then I'm stuck as I don't know how to debug and work in VBA or understand what has gone wrong. I want to record a single macro that always remains relative to the last 'Total Due' column heading (in the sample, it’s cell FF3 but on another worksheet could be cell GA26) and thus enables me regardless of where on the worksheet the rent statement is placed to add through my recorded macro a further four columns with updated dates and a repositioned 'Total Due' summary (in the sample in cells FE23 and FF23). The contents of cells FE23 and FE22 are always the same number of rows from the 'Sample Rent Statement, Service Charge and Sub Total' rows. I've searched on the web and in the help files of Excel 2007 but have been totally stumped by this, so currently I have to re-record a quantity of macros each month to cover all of the permutations of the worksheets in my Excel rent workbook, which is starting to become pointless in terms of saving time. Does someone know a solution to this problem please?!

  Read the article

• is there a way to run a command before puppet implements a change?

  - by Patrick

  I want to have puppet run a specific command before performing any type of change. I am aware of the prerun_command option in the main puppet.conf, but this is not what I'm looking for. I want the command to only run if something is about to change, not on every puppet run. Here's the scenario. Let's say I have a bunch of web servers behind a load balancer. I then want puppet to update the web site files. But in order to prevent issues where some files have been updated, but other files haven't, and the mixed versions causing problems, I want to take the server out of the load balancer pool. I could write a script which when run will tell the load balancer to remove the box from the pool. Then puppet can do the change, and use postrun_command to put the box back in the pool once complete. But I need a way to run that script to remove the server from the pool. The only solution I can think of is to keep 2 copies of the files on the box. One a staging copy, and when puppet updates that, use a notify action to trigger the removal script, and then copy from staging into the live location. But I was hoping for something a little more generic that would work on any change being performed (upgrading a package, restarting a service, creating a user, anything).

  Read the article

• D-Link wireless router losing outbound data

  - by gsteinert

  I have a Linux box running the Apache web server behind a D-Link wireless router (nothing fancy, just standard kit that comes with Virgin Media broadband). My issue is that when requesting web pages (from within the network or via the web), the back end of the page seems to be being dropped. For example, I tried to display a text-only file, and all I could get was the first 40-70% of the file (it changed slightly with each refresh). The apache access logs show that only part of the data was being sent (~6000 bytes instead of the 12000+ bytes of the file). Removing my router from the equation fixes the issue and I can download any files no matter the size with no problems. My theory is that the uploaded packets are either being dropped or held up by the config of the router. Is there anything I can do to alleviate the problem? (Perhaps a way of reconfiguring the router to upload packets harder/better/faster/stronger or an option in apache that provides a workaround) As a last resort I will get a second NIC for my Linux box and turn it into a router, but that would mean the box will be on 24/7... not the most ideal of circumstances. Gary

  Read the article

• Transfer of ownership of Windows 7

  - by ziggy

  I am thinking of purchasing a copy of Windows 7 via either ebay or GumTree. I am unsure as to how the product key works. A close friend of mine is warning me against buying it from ebay as he is suggesting that once it has been used, the operating system registers itself on microsoft servers using the serial number of the motherboard of the system where it has been installed. This means once installed on one machine you wont be able to install it on another machine. Now i am struggling to believe that an operating system can only be installed on one machine. Can someone please explain exactly how this works. I can see a lot of copies being sold on Ebay which are used. I used the 'Ask a question' option and the majority of the users are saying that i should be able to use it. If someone buys Windows 7 from the shop, installs it on his PC but then decides that he wants to sell it can he not sell it? Will the person buying it not be able to use it? Does the person selling it have to somehow unregister it first? What do i need to look out for if buying it from Ebay? Thanks

  Read the article

• Unnamed, hidden partitions on my 500 GB HD, HP Pavilion dm4 Laptop

  - by emotionull

  I have multiple doubts here. Its a Seagate 500GB 7200RPM HD. I had installed it few months back after my original Laptop HD stopped working. The current drives on my latop, as shown by the Windows Disk Management are: After installing the new HD, I had done a complete clean install of Windows 7 and I didn't create any parition myself, manually. So there are 4 drives. Even previously, before I installed this new HD, my laptop had 4 Partitions. But the there were no un-named partitions like the two in this case. The other two were HP tools and Recovery or something. It was pre-configured, Factory installed Windows. Also, now when I right cick on the unnamed Drives from Disk Management, all the options are greyed out (see image) except the delete partition image. So how do I know what's inside those partitions? Will it be ok if I delete them? I want install Ubuntu and dual boot it with my current windows installation. I cannot do it in current setup as there are already 4 partitions of my HD and if I will try to make a new partition, it will be a logical one (correct me if I am wrong here). So can I delete the un-named, hidden partitions and use them for Ubuntu? A bit unrelated question. As a backup option, can I use the Windows 7's Backup and Restore facility to keep a complete backup of all the drivers and system softwares.

  Read the article

• Unexpected media key behavior on new Acer Aspire

  - by Morgan May

  I'm having weird issues with the media keys (play/pause, previous, next, etc.) on a new Acer Aspire laptop. This is the first Acer I've owned and also my first Windows 7 computer, so I'm not sure whether the behavior is a result of some hidden Acer process that I haven't rooted out yet, or some Windows 7 option that I'm not aware of, or something else. I'm experiencing two issues that I suspect are related. Both problems are intermittent but happen more often than not. The media player I'm using is Winamp. I'm pretty sure I've had the same problem when using other media players, but when I tried to verify that before posting this, I only had the problems with Winamp. Because the problems are intermittent, I'm not sure if that's significant. 1) When I press the Play/Pause media key, in addition to playing or pausing the media player, it brings up a little menu in the center of the screen that lists my removable drives (CD/DVD, USB drives, etc.). To make the menu go away I have to either click away from it or hit Escape. Selecting a drive on the menu doesn't seem to do anything. 2) When I press the Previous or Next media keys, it skips 2+ tracks instead of just one (the exact number seems to vary). I've poked around all the control panel options that I can find, and looked through all the utilities that came with the computer with no luck. There's nothing that I can find in the (very slim) documentation, either. I have a hunch that the problem is caused by whatever utility manages global hotkeys, but I haven't found any way to configure that. Any guidance would be greatly appreciated. UPDATE: It looks like Winamp was the culprit. I did have the problem when using other media players, but when I uninstalled Winamp, the problem went away. I'd like to use Winamp, but I can survive with other players.

  Read the article

• How do I view source in Outlook 2010?

  - by Martin Duys

  This question has already been asked here; but the answer only gives advice on how to view the email header not the actual html source of the email. There is another question here, which I think may be caused by the same issue as mine, but does not have a satisfactory answer (the answer does not work for the person who posted the question) If I right click on the bottom of an email I can see the option to 'view source' but when I select it nothing happens. I have done a bit of research and came across a post for a much earlier version of Outlook that suggested adding something into the registry. I applied this advice, but it made no difference; but I'm pretty sure that applying this solution correctly for my circumstances will do the trick. When I first received this machine it had a demo version of UltraEdit installed. I uninstalled UltraEdit and installed Notepad++ instead. I am convinced that there is a registry entry that is pointing to UltraEdit as the default view for 'view source' in my email and I need to replace this entry with a reference to Notepad or Notepad++, but I don't know how to do this. Any suggestions?

  Read the article

• Robocopy (without /l flag) running for hours making log file huge, but not actually copying anything

  - by Mickster

  Here's my command: Robocopy C: C:\C_root /FP /BYTES /TEE /S /E /COPYALL /DCOPY:T /MOVE /Z /ETA /XJ /R:2 /W:30 /XF pagefile.sys /XD /LOG:C:\robocopy.log. BTW, notice the /XD option above. After that I had a few directories that I want to omit. I showed these between angle brackets like this: (left angle bracket) a few dirs I wanted to exclude (right angle bracket). Amongst these dirs was the C_root dir itself, so that it did not get into an "infinite" recursion. (This part was stripped from the post because angle brackets apparently have a meta-meaning to superuser.com about hyperlinks.) The command window this was running in listed a few "EXTRA" files then "hung". By this, I mean no more output, no cmnd prompt, and if I tried to scroll it up, it would immediately scroll right back to the bottom. After about six hours, it finally finished, although I never got a cmnd prompt back in the window I started it in. DIR shows the log file at more than 1.3GB, but when I try to do a MORE on it, I get "Cannot access file". C:\C_root never grew larger. Does anyone have an idea what is going on here?

  Read the article

• Are there any benchmarks showing difference between hardware virtualisation enabled/disabled?

  - by Wil

  I have a 13" sub-laptop/large-netbook, it has an AMD Athlon Neo X2 L335, and I chose this one because it supports hardware virtualisation. In the end, I hardly do any virtualisation on it, however, when I do... it is fast. To my shock, I went in to the BIOS and saw that virtualisation was disabled! I turned this on and, I see no speed difference.... or at least none that I can tell. I do not have time to do a full set of benchmarks - and I run quite a bit of software on the host, so it wouldn't be scientific. I have searched quite a few places and I just can not find any benchmarks showing the difference of virtualisation bit enabled/disabled on the same hardware. Does anyone have any benchmarks they have seen that they can share? In addition, I know there was an uproar a while ago as Sony disable the hardware virtualisation on some models and only offer it in their higher models as a premium feature, however, apart from forcing an up-sell, are there any benefits to having it disabled e.g. battery/heat? I just can't find any information and can't work out why it would be disabled by default. Edit--- To add, The only thing I can find is that without it, you can not perform x64 virtualisation as fast. This is the only down side I can find. However, if this is the only difference, then I am still interested in the second part of the question - why offer the option to disable it?

  Read the article

• sudoer scheme to allow useful access to another web developer yet retain future control of a virtual

  - by Tchalvak

  Background: Virtual Private Server I have a virtual private server that I'm looking to host multiple websites on, and provide access to another web developer. I don't care about putting too many constraints on him, though I wouldn't mind isolating the site that he'll be developing from other sites on the server that I will develop. The problem: retain control Mainly what I want is to make sure that I retain control over the server in the future. I want to reserve the ability to create/promote/demote and other administrative functions that don't deal with web software. If I make him an admin, he can sudo su - and become root and remove root control from me, for example. I need him not to be able to: take away other admin permissions change the root password have control over other security/administrative functions I would like him to still be able to: install software (through apt-get) restart apache access mysql configure mysql/apache reboot edit web development configuration type files in /etc/ Other Standard Setups would be happily considered I've never really set up a good sudoers file, so simple example setups would be very useful, even if they're only somewhat similar to the settings that I'm hoping for above. Edit: I have not yet finalized permissions, so standard, useful sudo setups are certainly an option, the lists above are more what I'm hoping I can do, I don't know that that setup can be done. I'm sure that people have solved this type of problem before somehow, though, and I'd like to go with something somewhat tested as opposed to something I've homegrown.

  Read the article

• Viewing local websites on my iOS device over Wi-fi

  - by John

  Trying to view some local html/css/js files in a mobile browser on my iOS device. Thought maybe file-sharing would be an option, and is, but I'm not completely satisfied with it. Any time I try to do the following an error occurs. Web sharing is on and available at http://192.168.1.101/~user but I have to manually copy the files in. If I try to symlink a folder in so that the address could be viewed at ''~user/some_dir by issuing $ ln -s /Users/user/dev/some_dir ~/Sites/ then I get a 403 forbidden error. I've tried to remedy this by modifying a user.conf file in /private/etc/apache2/ and using the following syntax: <Directory "/Users/user/Sites/"> Options Indexes MultiViews SymLinks AllowOverride None Order allow,deny Allow from all </Directory> but nope, still doesn't work. I get a 403 error. If I try to symlink each individual file in instead of using a directory as a sub-directory, same error. Any help would be greatly appreciated! I'd just like to symlink directories into the ~/Sites one and browse them on my iOS device over wifi. I'm on OS X 10.7 Lion trying to connect with iOS 5.

  Read the article

• Transferring domain from one registrar to another

  - by Macha

  I have a domain from my old web host, which was free with my hosting account. After a few years, I am moving to a VPS. Most of my other domains were registered with Namecheap, so it was just a matter of changing a few DNS records. However, given that my old host does not provide me with a DNS control panel, and I don't want to be paying a full hosting bill for just domains, I'm now looking into transferring it. My old host says there will be a charge of $15 to them. NameCheap's page seems to imply you don't need the current registrar to do anything, but it also seems to be based on sending an email to the one listed in whois. Of course, my old host have whoisguard on the domain so the only email on it is [email protected] (and not a unique [email protected], just [email protected]) which doesn't go to me. Again, there doesn't seem to be an option to disable this. So, is it a case of paying my old host's fee, and paying again for the domain from NameCheap, or is there some other way to transfer my domain? (I'm not really sure which of the trilogy sites this is best for.)

  Read the article

• Recovering data from an external hard drive

  - by CCallaghan

  I have a WD Elements 2GB hard drive (formatted NTFS). I accidentally kicked out the USB cable while writing data to the disk, and now I can't access most of the data. Although this was ostensibly my backup drive, there is a great deal of important material on there which was only on there. I realise how idiotic this makes me. (So, formatting is not an option.) Things I've tried/information I've gathered: Windows Explorer will recognise the drive itself. However, it will not access most directories therein (and will sometimes crash when exploring). I can access all of the directories through the command line, but the dir command will often report that it can't read any files in most of the directories. The situation was similar when I hooked it up to an Ubuntu machine: the file explorer crashed, but I could access directories - but not files in those directories - via terminal commands. Several files I tried to copy out either resulted in an I/O error being reported or resulted in the command line crashing. The Disk Management utility on Windows reports a healthy disk formatted as NTFS and not RAW. It also indicates the correct amount of space used up and its capacity (so it seems that the files are not deleted). I've tried to run chkdsk, but that hangs on Step 2 (checking indexes) at 74%. Step 1 reported no bad sectors. I tried Recuva, but that didn't seem to work (stalled at 0% for half an hour). I should also note that the disk doesn't seem to be spinning smoothly; it seems to be chopping back, like it's reading the same sector over and over again. I noticed this after I kicked out the cable. Any help would be greatly appreciated. Update: It would seem the problem has taken a turn for the worse. The external hard drive now shows up on my computer as a local disk and is not mountable by Linux.

  Read the article

• Can't start my phpMyAdmin

  - by vrynxzent

  i am creating my own portable server but i can't make it to run the phpMyAdmin, the mysql, php and apache is running except for phpMyAdmin. When i check Apache's error log, it states [Fri Nov 09 08:54:37 2012] [warn] pid file F:/Drive WebServer/Drive WebServer/bin/Debug/Apache2bak/logs/httpd.pid overwritten -- Unclean shutdown of previous Apache run? PHP Warning: PHP Startup: Unable to load dynamic library './php_mysql.dll' - The specified module could not be found.\r\n in Unknown on line 0 PHP Warning: PHP Startup: Unable to load dynamic library './php_mysqli.dll' - The specified module could not be found.\r\n in Unknown on line 0 [Fri Nov 09 08:54:37 2012] [notice] Apache/2.0.64 (Win32) PHP/5.2.17 configured -- resuming normal operations [Fri Nov 09 08:54:37 2012] [notice] Server built: Oct 18 2010 01:36:23 [Fri Nov 09 08:54:37 2012] [notice] Parent: Created child process 6784 i manually assign the exact path for this F:/php/ext/php_mysql.dll PHP Warning: PHP Startup: Unable to load dynamic library 'F:/php/ext/php_mysql.dll' - The specified module could not be found.\r\n in Unknown on line 0 but still the same error. i set this option in php.ini extension_dir = "./" another error goes pops out It says libmysql.dll is missing. PHP Version : 5.2.17 Any help would be appreciated. ;)

  Read the article

• Vim move cursor one character in insert mode without arrow keys

  - by bolov

  This might seem a little too overboard, but I switched to vim and I so happy about the workflow now. I try to discipline myself not to use the arrow keys, as keeping the hands on the alfa-keys all the time is such a big thing when writing. So when I need to navigate I get out of insert mode, move in normal mode and get back in insert mode. There is an exception where this is actually more disrupting: I use clang complete with snippets and super tab which is great. Except every time I get a function auto completed after I fill in the parameters I am left with the cursor before ) so to continue I have to move the cursor one character to the right. As you can imagine this happens very often. The only options I have (as far as I know) are : Escla or ?, and I am not happy about neither of them. The first one makes me hit 3 keys for just a simple 1 character cursor move, the second one makes me move my hand to the arrow keys. A third option would be to map CTRL-L or smth to ?. So what is the best way of doing this? //snippets (clang complete + supertab): foo($`param1`, $`param2`) //after completion: foo(var1, var2|) ^ ^ | | I am here | Need to be here | denotes cursor position

  Read the article

• How to make a redundant desktop system with daily snapshots? (Is btrfs ready for use?)

  - by TestUser16418

  I want to configure a desktop system in which the home filesystem would be redundant (e.g. RAID-1), and would have weekly snapshots taken. I've already done this with ZFS, the snapshot system is wonderful, and with send/recv you can easily create backups on external media. Unfortunately, at that point, I want GNU+Linux and not FreeBSD or Solaris, so I'm looking for suggestions for good alternatives. I reckon that my alternatives are: btrfs - it seems to be exactly what I need, it has snapshots and commands that allow you to easily replicate zfs send. Yet all documentation mentions that it's still experimental. I can't seem to find any actual reports on its reliability or usability issues. Can you point me to any information on that issue that could clarify whether it would be a possible choice? I have a large preference for this option, mostly because I don't want to reformat the drives when btrfs becomes ready, but I there's no information on whether it's usable at all, whether it's a silly idea to use it, etc. The question that I cannot get the answer to is what does "experimental" mean. lvm snapshots and ext4 - preferably not, since it can consume an awful amount of space when new files are created. Creating 200 GB files requres 200 GB free space and 200 GB additionally for snapshots. I also have found it unreliable -- failed metadata rewrite results in an unreadable PV. I'm wondering how btrfs would compare here. A single filesystem (ext4) on a RAID-1 array with custom COW snapshots with hardlinks (like cp -al). That's my current preference if I can't use btrfs. So how experimental btrfs is, which should I choose, and do I have any other options? What if I don't keep external incremental backups, would that affect my choice?

  Read the article

• How do I install Apache Portable Runtime?

  - by apache

  My Apache is installed by yum install apache And now I'm trying to install subversion server from source following instructions here. But when I try to configure,get an error: [root@vps303 subversion-1.6.9]# ./configure configure: Configuring Subversion 1.6.9 configure: creating config.nice checking for gcc... gcc checking for C compiler default output file name... a.out checking whether the C compiler works... yes ... checking for APR... no configure: WARNING: APR not found The Apache Portable Runtime (APR) library cannot be found. Please install APR on this system and supply the appropriate --with-apr option to 'configure' or get it with SVN and put it in a subdirectory of this source: svn co \ http://svn.apache.org/repos/asf/apr/apr/branches/1.2.x \ apr Run that right here in the top level of the Subversion tree. Afterwards, run apr/buildconf in that subdirectory and then run configure again here. Whichever of the above you do, you probably need to do something similar for apr-util, either providing both --with-apr and --with-apr-util to 'configure', or getting both from SVN with: svn co \ http://svn.apache.org/repos/asf/apr/apr-util/branches/1.2.x \ apr-util configure: error: no suitable apr found How do I get around this problem? BTW,will both client and server software be installed by compiling from source?

  Read the article

• Driver corruption when deploying Dell Touchpad Drivers (with software) during imaging process

  - by BigHomie

  We're an sccm shop, and use it to deploy Windows. When deploying Dell laptops (multiple models), the touchpad drivers seem install properly, but the software doesn't. The resulting problem is that when the touchpad is pressed on occasion, the mouse pointer will 'jump' to certain points on the screen. A possible symptom of this problem/visible sign is if the touchpad icon isn't in the system tray. The software is in the control panel, but when opened part of the gui is pixelated, indicating botched install maybe? The manual resolution to this, is to go into device manager and uninstall the driver with the option to uninstall all driver software. After a restart, the driver and software is apparently reinstalled, and from there works as expected. Obviously this partially defeats the purpose of a zero touch deployment. If anyone knows why this is and/or a possible workaround, those answers would be valid as well. Barring that, I want to find a way to deploy the driver and touchpad software in an unattended way, so that it can be conditionally installing during the imaging process. To be honest I'm not sure how to troubleshoot this, I suppose I could try drvinst.exe to install the driver, but finding out why this fails initially would keep me from spinning my wheels.

  Read the article

• haproxy + nginx: https trailing slashes redirected to http

  - by user1719907

  I have a setup where HTTP(S) traffic goes from HAProxy to nginx. HAProxy nginx HTTP -----> :80 ----> :9080 HTTPS ----> :443 ----> :9443 I'm having troubles with implicit redirects caused by trailing slashes going from https to http, like this: $ curl -k -I https://www.example.com/subdir HTTP/1.1 301 Moved Permanently Server: nginx/1.2.4 Date: Thu, 04 Oct 2012 12:52:39 GMT Content-Type: text/html Content-Length: 184 Location: http://www.example.com/subdir/ The reason obviously is HAProxy working as SSL unwrapper, and nginx sees only http requests. I've tried setting up the X-Forwarded-Proto to https on HAProxy config, but it does nothing. My nginx setup is as follows: server { listen 127.0.0.1:9443; server_name www.example.com; port_in_redirect off; root /var/www/example; index index.html index.htm; } And the relevant parts from HAProxy config: frontend https-in bind *:443 ssl crt /etc/example.pem prefer-server-ciphers default_backend nginxssl backend nginxssl balance roundrobin option forwardfor reqadd X-Forwarded-Proto:\ https server nginxssl1 127.0.0.1:9443

  Read the article

• Formatting not retained in paste from Ditto (clipboard manager). Plain text pasted instead [Solved] Add supported types

  - by Jeff Kang

  I'm trying to use Ditto on the Ditto documentation. If I were to copy the table of contents, then paste it (without Ditto) to the word processor, I get http://i.imgur.com/V1GU3.png, and the formatting is maintained. As as a result of the copy operation, the table of contents also goes into the Saved Items List (= History List = Lists the Clips saved from the Clipboard) in Ditto’s Main Window: I open a blank document to paste from Ditto instead of the default clipboard, and press either Ctrl-`, the default Ditto window activation Global Hot Key, or click the tray icon. From this point, I can do 3 things to close the Ditto window, and place the item on the clipboard (the default clipboard?). Select the item, and press Enter Put the cursor on the item, and double-click Select the item, and press Ctrl-c 1) and 2) send a right-click where the cursor is, after the Ditto window closes (presumably to have the paste option ready to access?): Ctrl-c just closes the Ditto window. Whichever method is used, the contents are pasted in what I believe is plain text: http://i.imgur.com/mQAZH.png How do I keep the formatting that the default clipboard keeps? Thanks.

  Read the article

< Previous Page | 569 570 571 572 573 574 575 576 577 578 579 580  | Next Page >