Search Results

Search found 19997 results on 800 pages for 'software schedules'.

Page 575/800 | < Previous Page | 571 572 573 574 575 576 577 578 579 580 581 582  | Next Page >

  • Excluding certain file types in wget

    - by Alan Spark
    I have been using wget for a while now to mirror files from an ftp server to a local folder. My wget command is as follows: wget -mirror -w 1 -p -nH -P /var/www/ ftp://my-ftp-server However, I just noticed that it is copying over a .listing file for every folder that it visits. So, even if nothing has been changed on the ftp server, a .listing file will always be copied. My understanding is that the .listing file is created when wget opens the ftp session. Is there a way to avoid this? I've tried the -R option (e.g. -R .listing) but this didn't help. See: http://www.gnu.org/software/wget/manual/wget.html#Recursive-Accept_002fReject-Options Thanks, Alan

    Read the article

  • File corruption when copying different file on raid 1

    - by Stephan
    I have a RAID 1 configuration of 2 1TB drives on a Fedora 12 box. Most of what is stored there are video files that are numerical labeled. The problem I'm having is that I had one of the video files get corrupted. I copied a replacement from a backup and replaced the bad file and now it works fine. However, after doing this the next numbered file goes from 350MB to 200KB and all but about .5 second of video disappears. If I then replace that file it happens to the next one down the line. Ex: Replace corrupt file 1.avi and file 2.avi shrinks to 200KB. Replace now corrupted 2.avi and it works but 3.avi gets screwed up. I have run SMART tests on the drives and they report fine. Does anyone have any tests I can run to try to figure out what is going on? EDIT: It is a two disk software RAID 1 with an ext4 filesystem

    Read the article

  • Error when installing ubuntu-zfs

    - by ubiquibacon
    I'm switching from FreeNAS to Ubuntu 12.04 LTS. After a vanilla install of Ubuntu has been completed I run the following commands in the order shown to install ZFS: apt-get install python-software-properties add-apt-repository ppa:zfs-native/stable apt-get -y -q update && apt-get -y -q upgrade apt-get install ubuntu-zfs When the last command is run ZFS is installed and seems to be working correctly... mostly (more on that later). However, when the last command is run I get this error (full log here): configure: error: *** Please make sure the kmod spl devel <kernel> package for your *** distribution is installed then try again. If that fails you *** can specify the location of the spl objects with the *** '--with-spl-obj=PATH' option. What is this error and how do I fix it? Now I said mostly earlier because my pool's don't auto mount when the server restarts the way they should. All my reading (mostly from this page) indicates that mountall should just take care of the mounting. I have followed the instructions on that page and I cannot get mountall to work correctly. My pools will only auto mount on restart if I edit /etc/fstab or change the ZFS_MOUNT and ZFS_UNMOUNT options in /etc/default/zfs.

    Read the article

  • You are or will be a laid off programmer - what do you do a year ago, right now, tomorrow, and next week?

    - by Adam Davis
    Many programmers, software engineers, and other technology professionals are out of work, facing layoffs, or are unprepared for layoffs though they feel secure right now. What should every programmer do right now (even if secure in their current job) to prepare them for layoffs down the road? If your boss came to your cubicle while you read this and laid you off: What would you do immediately after? What would you do tomorrow? What would you do next week? It obvious that one should always have an up to date resume, always get recommendations from people when they see you at your best (not when you're looking for a new job), etc. What are the things, step by step, that every programmer should do (or should consider doing) long before they are laid off, when they're laid off, and shortly after being laid off? This is a question with many possible facets. While I want to encourage discussion to center around programming career based answers, please reconsider before downvoting someone because they're thinking in terms of how they're going to prevent going into debt. Bonus catch-22 type question: You can study a new language or technology while out of work, but most places want you to have more than 1-2 months experience in a working environment, not just from a learning exercise. Is it worthwhile to place a priority on new (ideally in demand) skills, or should you instead hone existing skills?

    Read the article

  • SSL certificates with password encrypted key at hosting provider

    - by Jurian Sluiman
    We are a software company and offer hosting to our clients. We have a VPS at a large Dutch datacenter. For some of the applications, we need an SSL certificate which we'd like to encrypt with a password protected keyfile. Our VPS reboots now and then because of updates whatsoever, but that means our apache doesn't start right away because the passwords are needed. This results in downtime and is of course a real big problem. We can give the passwords to our VPS datacenter, or create certificates based on keyfiles without passwords. Both solutions seem not the best one, because they compromise the security of our certificates. What's the best solution for this issue?

    Read the article

  • Text comparison utility

    - by Aaron
    I know this has been asked before...but I have a spin as I have been trying out varying free software offerings. I want to rid out department of DiffDoc the problem is that I am having trouble locating something that will do what we need. WinMerge has been the latest attempt... The problem is simple. One Word doc...one PDF with a portion of it containing the text to be compared against. Compare them and be done. Raw text, ignore whitespace, ignore carriage returns, etc... Just compare the text and give me the results in some sort of report. NOTE: Have tried ExamDiff, kdiff3, Tortoise, and a few others...

    Read the article

  • How can I use a computer as a router and send all client traffic through anonymous proxies?

    - by Terrapin
    Is there a way that I can setup a spare box as a router on my network, and route client traffic through a proxy in order to hide my location? Specifically, I would like internet traffic to/from my Roku Box to be routed via proxy, but there is no proxy support built in to the Roku. So I would like wire my Roku directly my computer's second NIC, and force all traffic through a proxy. What kind of software and hardware setup will I need? Also, which anonymous proxy service are best for this purpose? I'm not interesting in full anonymity or encryption. I simply want to mask my location while providing the best possible throughput.

    Read the article

  • Is the development of CLI apps considered "backwards"?

    - by user61852
    I am a DBA fledgling with a lot of experience in programming. I have developed several CLI, non interactive apps that solve some daily repetitive tasks or eliminate the human error from more complex albeit not so daily tasks. These tools are now part of our tool box. I find CLI apps are great because you can include them in an automated workflow. Also the Unix philosophy of doing a single thing but doing it well, and letting the output of a process be the input of another, is a great way of building a set of tools than would consolidate into an strategic advantage. My boss recently commented that developing CLI tools is "backwards", or constitutes a "regression". I told him I disagreed, because most CLI tools that exist now are not legacy but are live projects with improved versions being released all the time. Is this kind of development considered "backwards" in the market? Does it look bad on a rèsumè? I also considered all solutions whether they are web or desktop, should have command line, non-interactive options. Some people consider this a waste of programming resources. Is this goal a worthy one in a software project?

    Read the article

  • What you'd need to setup BBS?

    - by raspi
    What I need to setup BBS nowadays? I'm thinking of BBBS or PCBoard (no telnet! too new technology). What I've thinked so far, I'd need: virtual machine which runs DOS and hook that virtual COM-port to somekind of virtual VoIP modem software somehow (is there any?). How you can call to it across internet? Can you use HyperTerminal straight with that virtual/real modem? Or will VoIP just garble the modem data and nothing will work?

    Read the article

  • Failed to fetch *.deb Size mismatch, then packages with unmet dependencies [solved]

    - by user113907
    I recently bought the wonderfully looking and reviewed Amnesia The Dark Descent and I'm trying to install it. The first time I tried to download it, I had to stop in the middle of the download (may have broken something). The second time I tried to download, at the end of the download it gave me the following error: Failed to fetch https://private-ppa.launchpad.net/commercial-ppa-uploaders/amnesia/ubuntu/pool/main/a/amnesia/amnesia_1.2.1-0ubuntu2_i386.deb Size mismatch Now, whenever I try to download it, it gives me this error: The following packages have unmet dependencies: amnesia: Depends: libalut0 (>= 1.0.1) but it is not going to be installed Depends: libc6 (>= 2.4) but 2.15-0ubuntu10.3 is to be installed Depends: libfontconfig1 (>= 2.8.0) but 2.8.0-3ubuntu9.1 is to be installed Depends: libfreetype6 (>= 2.2.1) but 2.4.8-1ubuntu2 is to be installed Depends: libgcc1 (>= 1:4.1.1) but 1:4.6.3-1ubuntu5 is to be installed Depends: libopenal1 (>= 1:1.13) but 1:1.13-4ubuntu3 is to be installed Depends: libsdl1.2debian (>= 1.2.10-1) but 1.2.14-6.4ubuntu3 is to be installed Depends: libstdc++6 (>= 4.1.1) but 4.6.3-1ubuntu5 is to be installed Depends: libxft2 (> 2.1.1) but 2.2.0-3ubuntu2 is to be installed Depends: zlib1g (>= 1:1.1.4) but 1:1.2.3.4.dfsg-3ubuntu4 is to be installed I already searched the net and ran a few command line commands. Ex: sudo dpkg --configure -a sudo apt-get install -f Or configure the software packages to download from Main instead of the local UK server. But I'm really not figuring out a solution. I have a fresh install of the latest LTS (12.04). The only non-standard thing so far is that I installed gnome-shell (?) because I really can't stand Unity. Help would be much appreciated. I am currently more than entertained enough with World of Goo and Command & Conquer, but I will want to play Amnesia in the close future.

    Read the article

  • What does Libre Office do to an existing Excel sheet to bloat its size?

    - by Sn3akyP3t3
    I try to avoid using Libre Office on existing Excel created workbooks because of the potential for unpleasant results. In this case Libre Office bloated the size of the workbook for some reason unknown to me. I would like to know if Libre Office does this to all Excel workbooks or just something in that workbook that causes it. Software involved: Microsoft Office Excel 2010 Libre Office 3.5.x (exact version unknown) Dropbox (merely to sync changes) Platforms involved: Office on Windows (master of the obvious on that one I suppose..) Libre Office on Mac OS 10.6 Types of data stored in this workbook: Text Integers 1 column with a simple formula spanning the entire worksheet representing that particular row (=CONCATENATE(A2285,B2285,D2285), =CONCATENATE(A2286,B2286,D2286), etc.) Total of 3,500 plus rows Here is a photo with details described within, but I'll go ahead and explain the photo as well: This screenshot is from Dropbox history of the .xlsx workbook. Version 61 - 68 were Office Excel. Version 69 - 73 were Libre Office.

    Read the article

  • Bizarre SSH Problem - It won't even start

    - by thallium85
    I recently got Ubuntu 12.04 Precise, got it up and running with some MediaWiki software, static IP on the box and router and was able to access the main page even from a cell phone. Everything seemed great... Then I wanted to finally get rid of the monitor and keyboard and login remotely via SSH. I installed openssh-server, let everything point to port 22 for a test run and installed putty on my Windows XP machine. I got a connection refused. Went back and started checking the Ubuntu install itself... (I'm under root from this point on) $ sudo -s $ service ssh status ssh stop/waiting $ service ssh start ssh start/running, process 2212 $ service ssh status ssh stop/waiting Apparently ssh has stopped or is waiting for something.... $ ssh localhost ssh: connect to host localhost port 22: Connection refused I can't even connect to myself... I checked ufw (firewall) to see if port 22 is doing alright... $ sudo ufw status Status: active To Action From 22 ALLOW Anywhere 22/tcp ALLOW Anywhere 22 ALLOW Anywhere (v6) 22/tcp ALLOW Anywhere (v6) sshd_config shows only Port 22 Is ssh not using the right IP address at all? I just don't get what I did wrong here. When this is up and running I will def change the port number, but for now, I don't want to mess with the default install too much until a test run with putty is successful. Edit: Here are my sshd_config file and my ssh_config file. The command /usr/sbin/sshd -p 22 -D -d -e returns: /etc/ssh/sshd_config line 159: Subsystem 'sftp' already defined. Edit: @phoibus moving the sshd_config file and reinstalling did the trick! service ssh status the above command shows that ssh is now running and I am now able to log in from my windows xp computer remotely via putty. Thanks so much! I can now use my monitor for other things!

    Read the article

  • Experienced programmer, beginner at web design, tools for effective maintainable web design? [closed]

    - by Clinton
    I do quite a bit of programming in my work, which I'm comfortable with, but recently I've being trying to do some web-design for non-work related reasons. I've got a Drupal site up and running, and added some content. But they all look fairly basic. Header with some content. It doesn't look particularly polished. Anyway, as an example, what I wanted to do was make some "bubbles", each with some text in them. From a programmers point of view, say: bubble(question_text, answer_text) might expand to a box with some border, with "Question: " + question_text then "Answer: " + answer_text. Of course I'd have lots of these bubbles, but I'd like to change their look and feel in one place, so simple HTML would be a maintainable nightmare. I also want to lay them out on the screen in some fashion. I was thinking a mixture of javascript and CSS, or possibly use PHP which Drupal uses. On the other hand, I fear I might be taking a 1990s approach to this, and that there's actually tools available now that make this process a lot easier. I'm just wondering what the best approach to this sort of task is? Should I be using offline web design software and copying the code to Drupal, and if so, any recommendations? I'm sorry if my question is a bit vague, because I'm not really sure what question I should be asking. I'd appreciate if you answer and comment, and I'll try my best to be more specific as I understand more.

    Read the article

  • Disadvantages of enabling AHCI after Win7 install

    - by Mario De Schaepmeester
    I've formatted my notebook that has a 5400RPM HDD with ~500GB capacity. After installing Windows 7 and about half the drivers (including chipset) I began to doubt whether to go for IDE or AHCI mode for my hard drive. There used to be a lot of discussion on the internet which is better and so far I understood it was particularly helpful on SSDs. Now the general consensus seems to be that AHCI mode is best for most hard drives. I have thus enabled AHCI in the middle of configuring my notebook (rest of the drivers, necessary software etc...) Two questions: considering my HDD's spec above, should I leave it on? Is there any disadvantage of enabling it after Windows 7 and chipset drivers installation? Windows 7 version is 64 bit Home Premium.

    Read the article

  • Ubuntu server hangs on reboot "could not stat resume device file"

    - by matnagel
    Instead of booting into the running system this machine stops and on the terminal I can see a message: could not stat resume device file /dev/sdb5 When I attach a keyboard and press enter the boot continues and the machine comes up like normal. But it's essential that this machine comes up under most circumstancs alone. There never was something like a "resume" on this machine. I tried several times to reboot, but this does not happen on all boots, I can not find a pattern here. There is a software raid running on the box. This is the syslog during boot: http://privatepaste.com/ff0fd0a51c/sdabfjahfgasjkgfu4gfsdzjcgfafasdjfhgasdcjfgauzfgafasgdufzg How can I get rid of this boot failure? We do not need resumes and best would be something that works here and now.

    Read the article

  • Is ZeroMQ a good choice to make a Python app and a C# managed assembly work together?

    - by Alex Bausk
    I have a task that involves talking to a .NET-based API (namely AutoCAD) to retrieve data, send commands, and react to events. I want to separate the API operations and the proper program logic (largely already implemented in Python) by using natural tools for both: a C# DLL for the former and a Python app for the latter. To connect these two pieces, I began exchanging JSON in ZeroMQ messages. I'm at early development stages but having recently discovered that ZeroMQ does not guarantee message delivery/order, I have reservations about whether this is a feasible way to go. Right now my app is a very basic REQ/REP pair and I plan to handle reacting to events and executing different commands by adding some sort of 'recipient-function' field to my message format. The reason that I want to use ZMQ is that I might be able to scale the software into a larger, multi-user, distributed solution sometime. I am a lay programmer so I would ask for your advice about this architecture. Should I just go ahead with it and plan to deal with message reliability/ordering when problems appear? Should I consider developing some kind of a REST wrapper around ZMQ?

    Read the article

  • International Dvorak keyboard doesn't trigger hot-keys

    - by akurtser
    I'm using the Engilsh-Dvorak keyboard-layout; My second keyboard language is Hebrew, which has nothing to do with Dvorak but the hot keys (e.g if I'm writing a document in Hebrew and want to make some bold text using Ctrl+b). The default Hebrew keyboard that comes with Windows (7 and below) has a shift mode which matches each Hebrew character with its matching English QWERTY character ). Obviously I'd want to use the Dvorak corresponding key rather than the QWERTY one, so I created a Hebrew-Dvorak keyboard with a software called Keyboard Layout Manager (KLM) which creates new keyboard layouts DLLs. It works just fine for the shift key, however, Ctrl-key triggered hot-keys (e.g Ctrl+l in FF) are being matched to the corresponding QWERTY key. I've examined the properly working English-Dvorak layout using KLM and in it's "Ctrl+ pressed" view, there isn't any character that's matched to any key but still I tried to encode the Hebrew Ctrl+ pressed keys to work with their matching Dvorak keys, yet it had no effect.

    Read the article

  • Jetty8 virtual hosts

    - by Martin
    I have a server JAR that is deployed once per customer, it is the API server for their software package. To that end, the port for each API instance must be the same, so that anything programmed against it can always find it. Each instance is deployed on a different domain name The problem I'm having is that, even when using a SelectChannelConnector and setting the host property, I can't get two instances to run simultaneously, I get a BindException with "Address already in use". I suppose my question is: can Jetty do this, or do I need to do some external re-writing, or is there a better way I can go about achieving the same ends? Thanks.

    Read the article

  • Coordinate spaces and transformation matrices

    - by Belgin
    I'm trying to get an object from object space, into projected space using these intermediate matrices: The first matrix (I) is the one that transforms from object space into inertial space, but since my object is not rotated or translated in any way inside the object space, this matrix is the 4x4 identity matrix. The second matrix (W) is the one that transforms from inertial space into world space, which is just a scale transform matrix of factor a = 14.1 on all coordinates, since the inertial space origin coincides with the world space origin. /a 0 0 0\ W = |0 a 0 0| |0 0 a 0| \0 0 0 1/ The third matrix (C) is the one that transforms from world space, into camera space. This matrix is a translation matrix with a translation of (0, 0, 10), because I want the camera to be located behind the object, so the object must be positioned 10 units into the z axis. /1 0 0 0\ C = |0 1 0 0| |0 0 1 10| \0 0 0 1/ And finally, the fourth matrix is the projection matrix (P). Bearing in mind that the eye is at the origin of the world space and the projection plane is defined by z = 1, the projection matrix is: /1 0 0 0\ P = |0 1 0 0| |0 0 1 0| \0 0 1/d 0/ where d is the distance from the eye to the projection plane, so d = 1. I'm multiplying them like this: (((P x C) x W) x I) x V, where V is the vertex' coordinates in column vector form: /x\ V = |y| |z| \1/ After I get the result, I divide x and y coordinates by w to get the actual screen coordinates. Apparenly, I'm doing something wrong or missing something completely here, because it's not rendering properly. Here's a picture of what is supposed to be the bottom side of the Stanford Dragon: Also, I should add that this is a software renderer so no DirectX or OpenGL stuff here.

    Read the article

  • What is the lease irriating printer manufacturer?

    - by aireq
    Currently I have a Lexmark all in one printer/scanner which has some of the worse drivers I've seen for a printer. The installation takes forever. Then once it's installed the printer will only work if I keep the "Lexmark Productivity Studio" running in my system tray. Then later after I've scanned something 99% of the time the "Save to PDF" button doesn't do anything when I click it. It is also a wireless printer, but of course the only way to set any of the wireless settings is during the driver setup. So if my WEP key changes then I have to go off and reinstall the entire printer driver. Lately I tried refilling one of the ink cartridges with a key I bought off amazon, and now both the printer and the drivers keep complaining about being out of "Official Lexmark Ink" This comic from The Oatmeal pretty much sums up my feelings about consumer printers and their drivers. This question is, of course, pretty subjective but I'd like to know what (if any) consumer printer brands actual provide quality drivers and software with their printers.

    Read the article

  • Microsoft Tag Tagged Me

    - by Brian Schroer
    I got EXTREMELY lucky last week and won an HP Mini 311 notebook from a Microsoft Tag Twitter contest. I did my required tweet to enter last Tuesday, and one hour later received notification that I had won the weekly drawing. Apparently you can tweet up to 500 times (I pity the followers of those who do that), so it was really lucky that I won, and I sympathize with those who had been really trying. If you would like to try your luck, there are seven weekly prizes left, and you can find out about the contest here: http://tag.microsoft.com/ttcontest.aspx For a free PC, I thought it was the least I could do to find out what Microsoft Tag is. I was vaguely aware of those pastel-y triangle-y square things that look like someone put one of Don Johnson’s Miami Vice outfits through a shredder, and knew that the company I work for (one of the world’s largest consumer products companies) was looking into putting them on our products, packaging and advertising, but didn’t know much more about the technology. I thought they were just an improvement over bar codes, and would be used in retail store scanners, but I was mistaken. These tags are meant to be scanned by consumers using their mobile phones, to get instant access to information, websites, reviews, etc. Scanning a tag can open a web page, import a contact card, or dial a phone number, play a video… Tag reader software can be installed on Windows Mobile, iPhone, Symbian, Blackberry, Android, J2ME, and other phones (and I suspect that it will be available for Windows Phone 7 also :). There are built-in tracking, metrics and analysis tools, to help companies using Tag make decisions about their marketing expenditures. (And they don’t have to look Miami Vice-y – They can be customized to reflect the personality of the person or a brand.) Looks like interesting stuff. You can find out more at http://tag.microsoft.com.

    Read the article

  • Low Graphics and laggy screen after update to 13.10 from 13.04

    - by Wh0RU
    After updating from 13.04 to 13.10 many of 3D unity stuff has stopped working, I am suing Samsung Series 3 (NP350V5X) Laptop which has Switchable Intel and AMD Radeon HD 7670M GFX. xserver-xorg-video-ati does works but NO 3D support and graphics are very low. [I am currently using this] fglrx & fglrx-updates shows blank screen after Login. Intel Graphic Install doesn't work either (dependency error) Output of $ sudo lshw -c video *-display description: VGA compatible controller product: Thames [Radeon HD 7500M/7600M Series] vendor: Advanced Micro Devices, Inc. [AMD/ATI] physical id: 0 bus info: pci@0000:01:00.0 version: 00 width: 64 bits clock: 33MHz capabilities: pm pciexpress msi vga_controller bus_master cap_list rom configuration: driver=radeon latency=0 resources: irq:45 memory:e0000000-efffffff memory:c0120000-c013ffff ioport:3000(size=256) memory:c0100000-c011ffff *-display description: VGA compatible controller product: 3rd Gen Core processor Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 09 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:46 memory:bfc00000-bfffffff memory:d0000000-dfffffff ioport:4000(size=64) Similarly $ /usr/lib/nux/unity_support_test -p OpenGL vendor string: VMware, Inc. OpenGL renderer string: Gallium 0.4 on llvmpipe (LLVM 3.3, 256 bits) OpenGL version string: 2.1 Mesa 9.2.1 Not software rendered: no Not blacklisted: yes GLX fbconfig: yes GLX texture from pixmap: yes GL npot or rect textures: yes GL vertex program: yes GL fragment program: yes GL vertex buffer object: yes GL framebuffer object: yes GL version is 1.4+: yes Unity 3D supported: no Shows no 3D support. Can anyone please guide how to make things working again.

    Read the article

  • Is there a way to disable specific Spybot Immunization rules?

    - by Iszi
    I've been having problems using a desktop sharing application, which I've traced to the Immunization protections applied via Spybot S&D. Specifically, the problem has been narrowed down to the rules in the \SOFTWARE (Plugins) categories under the Internet Explorer groups. Once I disable these Immunization categories, everything in the application works fine. Each of these categories appears to include ~900 protections on the system. I suspect that the root cause of my problems could be narrowed down to just one, or perhaps a handful, of the settings that get applied in these categories. However, I can't find any options in Spybot S&D which would allow me to drill down to the individual protection rules and choose which to enable or disable. Is there something I'm missing, or is this not a feature available via the GUI? If it's not strictly supported in the application, is there a way to work around it by manually editing some of its files or registry settings? Spybot S&D version: 2.2.21.0 Spybot Start Center version: 2.2.21.129 Windows Ultimate x64

    Read the article

  • How to swap ctrl and fn key on a MacBook Pro running Windows 7 via Boot Camp?

    - by hobbes3
    There are sooooo many discussion on the internet about swapping the fn and ctrl key on a MacBook Pro. On the Mac side, a new software called ReMap4MacBook does a perfect job swapping the two key. But on the PC side (specifically Windows 7), I can't really find a definitive answer. Most post refer to this article but I read the loooong article and followed the instructions to no avail. I remember there used to be a program (maybe it was on XP) that not only swapped the two keys but it also controlled the fans on the MacBook Pro. But I can't remember the name and I also recall that that program stopped being updated like years ago. EDIT: It's called Input Remapper. So I am hoping there exist a simple program that I can simply run to swap those two keys.

    Read the article

  • MacBook Pro Trackpad freeze / holds click on its own

    - by lajuette
    My MacBook Pro's Trackpad shows an annoying behavior in the last few days. I think the only relevant thing that changed is the firmware for the Trackpad. An update has been distributed via Software Update a few days ago. Sometimes when i click somewhere the Trackpad won't recognize the mouseup, i.e. hold the click on its own. Clicking again seems to stop the holding and issue a new mousedown, but then again, no mouseup I.e. when i click on a file on the desktop the file will be dragged. But i can't stop dragging! Clicking in a browser or text document will select the text/images. Did anyone notice similar behavior? Any ideas or fixes?

    Read the article

< Previous Page | 571 572 573 574 575 576 577 578 579 580 581 582  | Next Page >