Search Results

Search found 16810 results on 673 pages for 'screen recording'.

Page 579/673 | < Previous Page | 575 576 577 578 579 580 581 582 583 584 585 586  | Next Page >

• after building in more ram, bios/debian does nothing [closed]

  - by derty

  My private server has 2x1gb Ram working with a 64bit Debian and an Q6600 Intel. This runs 2 virtual mashines on it each one recives 512mb RAM. Which you can immagine is a bit tight for the hole system. Now i got 2x2gb ram from a friend. I'm not sure if thery are clocking at the same speed, but i'm sure my power adaptor is not on his limit and can handle that. So there are 2 ram sockets left at the mainboard. I shuted down the system and build in the 4 gigs and looked what happen. After pressing the start button, everything gets noisy as known BUT the screen shows nothing, not even the bios stuff it usally does. Why isn't the system booting? I can immagine that it does not direkt link between booting debian and the bios not showing a thing. Or is it Grub? I mounted the system disk, and i can see it, switch folders write stuff with "vim" it does not seems like there is a problem.

  Read the article

• How does one skip “Windows did not shut down successfully” in Win7-64?

  - by XenonofArcticus

  Migrating an app from an expensive and unreliable dedicated embedded x86 box running WinXP-embedded to COTS hardware (Dell E6410 laptop) running normal Win7-64. At this time, it's not feasible to deploy using Windows 7 embedded. The problem is, that the system is still sort of "embedded". The power could shut off at virtually any time without prior warning. We've stripped the OS down and removed the battery capability so that it will power down as desired. The app never writes to the disk, so it's not like we're going to corrupt anything terribly. The system is essentially idle after our app is up and running (with the exception of some computation, graphics, and TCP/IP and serial communications) so the OS enters a pretty stable state rather quickly. After a power-loss however, it rightly complains that Windows did not shut down successfully and presents the user with the Windows Error Recovery text screen. If left alone, it does eventually move on booting just fine, but we'd like to skip that step if possible. WinXP-embedded is designed to do this automatically, so I know it's possible. I've looked at the Kernel Switches but I didn't see anything documented for "Skip Windows Error Recovery". I've also read extensively on the startup process: http://homepage.ntlworld.com./jonathan.deboynepollard/FGA/windows-nt-6-boot-process.html I know I can disable the auto chkdsk in the registry, but that's not the same thing either. So, how do I streamline the boot process to not hassle the user about a situation that will be the regular normal situation?

  Read the article

• Nvidia RAID 1 Problem. Degraded drives...

  - by Vedat Kursun

  I had a RAID 1 on my system which has a Gigabyte GA 8N SLI motherboard with a Nvidia chipset.(Nvidia Raid IDE ROM BIOS 4.84) When the system was working probably there used to be an icon on the system try which showed my two RAID disks. Bu after my friend accidentally clicked on the "Remove drive safely" icon while trying to disconnect her USB, I noticed that the RAID system wasn't working. After a reboot there was suddenly a failure message during boot screen. When I enter the Nvidia RAID setup utility (F10) I can see that both drives are degraded and that won't change even if I get into them and press R for Rebuild. Other options are only Delete and Exit. When I boot to Windows (XP Pro 32 Bit) I can see both my disks with the same data on each of them but my RAID 1 is broken. It's a relief to see that at least my RAID 1 was active but it's annoying not being able to rebuild it. Is there a way where I can rebuild my RAID 1 without having to delete the array and build it again? Cause I don't want to backup 400 Gigs of data and then recopy it to my drives... (Disks 2 x Seagate ST3500418 AS SATA Drives)

  Read the article

• Nvidia RAID 1 Problem. Degraded drives...

  - by Vedat Kursun

  I had a RAID 1 on my system which has a Gigabyte GA 8N SLI motherboard with a Nvidia chipset.(Nvidia Raid IDE ROM BIOS 4.84) When the system was working probably there used to be an icon on the system try which showed my two RAID disks. Bu after my friend accidentally clicked on the "Remove drive safely" icon while trying to disconnect her USB, I noticed that the RAID system wasn't working. After a reboot there was suddenly a failure message during boot screen. When I enter the Nvidia RAID setup utility (F10) I can see that both drives are degraded and that won't change even if I get into them and press R for Rebuild. Other options are only Delete and Exit. When I boot to Windows (XP Pro 32 Bit) I can see both my disks with the same data on each of them but my RAID 1 is broken. It's a relief to see that at least my RAID 1 was active but it's annoying not being able to rebuild it. Is there a way where I can rebuild my RAID 1 without having to delete the array and build it again? Cause I don't want to backup 400 Gigs of data and then recopy it to my drives... (Disks 2 x Seagate ST3500418 AS SATA Drives)

  Read the article

• New to server admin, Diagnosing Memory and CPU issues on DV

  - by G Thompson

  Sorry for my ignorance and lack of knowledge. I'm a PHP/Front-end developer just now venturing into very minor server management/diagnostics. I have a Media Temple DV account. I have 2 sites that run a PHP script through a subscription service to an API. Basically API hits site with said script. Script runs, gathers data from api, saves data to SQL database. I noticed that these sites seemed to causing memory overages on my server (not sure why). So I temporarily disabled them. The memory overage alerts stopped but my CPU still sits really high, like at 115% and above. I'm trying to diagnos this with tutorials and resources but just can't seem to find a solution. I'll attach screenshots(screenshots are without the PHP scripts I assume are responsible for the memory issues) I'm assuming are important to the diagnosis, but if anyone can point me in the right direction to start A. figuring out if and why the PHP script may be causing memory overages and B. Why my CPU is always over 100%. Thanks guys! Links to screen shots... can't post with low points. http://i.stack.imgur.com/A64k4.png http://i.stack.imgur.com/qm1rV.png

  Read the article

• Laptop keyboard stopped functioning properly

  - by galdikas

  Basically today out of blue my laptop keyboard started acting up. For example I press "s" but I see "`s" on the screen. Some keys don't work at all. And the weird thing is it keeps changing, in a sense that for example in the morning I press "s" and I get "`s", then few hours later "s" works correctly.. but pressing some other key output multiple characters. Then sometimes it spontaneously will start outputting some character onto any input field that is available as soon as I click on it to gain focus. And it will just keep on going and going, as if I keep a button pressed (which I don't). At first I thought this was a virus, but I have a dual boot of Windows 7 and Ubuntu, and I get same problem on both. I even tried to boo live CD, and still had same problem. Anyone had this kind of problem? It's a Toshiba Satellite c660-258. It is around year old, but quite well kept. Never spilled anything on it, or dropped it. And my wireless USB keyboard works perfectly on it (appart from the spontaneous character inputs, which I can stop by hitting NUM LOCK key)

  Read the article

• Arduino IDE "launch 4j" error

  - by John

  I have a computer running Windows XP. I am trying to run the Arduino IDE 0022. I double-click on arduino.exe, it waits about 30 seconds on the load up title screen, and then it gives me this error: Launch 4j: an error occurred while starting the application My only choice is to click "OK"; the error goes away, and the Arduino IDE closes. If I try to delete the Arduino files (to try overwriting with some different files), I get an error that doesn't allow me to do so: Cannot delete awt.dll: Access denied Make sure the disk is not full or write protected and that the file is not currently in use. The only way to delete the file is by restarting the computer. So something must still be trying to run after that first error. I have noticed in Task Manager that some Java programs are still running: javaw.exe (3 processes) I think this is a problem with Java, but I checked and updated all of my Java software and it is all up to date. I have looked on other forums for this issue and none of them seemed to help. From the forums I have tried: Different Arduino IDE versions Updating Java Opening arduino.exe as Administrator Nothing has worked. Anyone have any suggestions?

  Read the article

• Unexpected media key behavior on new Acer Aspire

  - by Morgan May

  I'm having weird issues with the media keys (play/pause, previous, next, etc.) on a new Acer Aspire laptop. This is the first Acer I've owned and also my first Windows 7 computer, so I'm not sure whether the behavior is a result of some hidden Acer process that I haven't rooted out yet, or some Windows 7 option that I'm not aware of, or something else. I'm experiencing two issues that I suspect are related. Both problems are intermittent but happen more often than not. The media player I'm using is Winamp. I'm pretty sure I've had the same problem when using other media players, but when I tried to verify that before posting this, I only had the problems with Winamp. Because the problems are intermittent, I'm not sure if that's significant. 1) When I press the Play/Pause media key, in addition to playing or pausing the media player, it brings up a little menu in the center of the screen that lists my removable drives (CD/DVD, USB drives, etc.). To make the menu go away I have to either click away from it or hit Escape. Selecting a drive on the menu doesn't seem to do anything. 2) When I press the Previous or Next media keys, it skips 2+ tracks instead of just one (the exact number seems to vary). I've poked around all the control panel options that I can find, and looked through all the utilities that came with the computer with no luck. There's nothing that I can find in the (very slim) documentation, either. I have a hunch that the problem is caused by whatever utility manages global hotkeys, but I haven't found any way to configure that. Any guidance would be greatly appreciated. UPDATE: It looks like Winamp was the culprit. I did have the problem when using other media players, but when I uninstalled Winamp, the problem went away. I'd like to use Winamp, but I can survive with other players.

  Read the article

• DVI output _only_ working on Windows, not during booting or on Linux

  - by Mononofu

  So yesterday I booted my laptop up and the external monitor I have it connected to just stayed black. At first, I thought the problem would go away when Ubuntu was loaded, but it didn't. I tried to reboot a few times, to no avail. Then I decided to give Windows 7 a try, and suddenly (at the login-screen), my external monitor turned on and worked like normal. I have connected the monitor via DVI, and this only seems to work with Windows now. I don't even get a signal in my BIOS! Mind you, everything was working fine before that, and I didn't change a single thing. I then tried to connect the monitor via VGA (from my DVI jack, which can output VGA using an adaptor), and it worked again. However, 1920x1200 using VGA looks like crap - black print on white background is basically illegible. Do you have any ideas how to fix this peculiar problem? I only use windows for gaming, so it's no real help that it still works normally. Please also excuse any spelling mistakes, I am practically typing this blindly. Edit: I only have one graphics card in my laptop, and I can't select anything related to that in my BIOS. In fact, I can pretty much do almost nothing there. My laptop is a Nexoc Osiris E703, graphics gard is a GeForce Go 7900 GTX. As I mentioned before, DVI output during booting and on Ubuntu was working fine for years before yesterday!

  Read the article

• Linksys SFE2000 Interface

  - by boburob

  I have a real problem with a layer 3 Linksys switch. First, every time it looses power, it seems to reset back to an older config. Not only this, but when this happens it looses interface settings on one subnet. This would not be a problem but I am completely unable to get to the interface on the working side. It allows me to log on and then just displays a blank screen. I have tried this on: IE6 IE7 IE8 IE9 Firefox 3.5 Opera Chrome All with the same results, except for Opera, which loads half the interface but nothing I can really use. I really need to get onto this switch so I can sort out routing and VLAN tagged ports, so if anyone has any ideas on either of these issues please let me know ASAP! Thanks! Also, due to its location and my lack of laptops with serial connections I cannot putty into it. UPDATE: Looked into this a bit more and it looks like this model of switch does not save the current config to boot unless you make sure to save it yourself, which explains the first issue, however the broken interface is more worrying!

  Read the article

• Windows Broken after Deletion of HP_TOOLS partition

  - by beanland

  When I decided to install Ubuntu on my laptop as a dual-boot, I recognized that Windows 7 was using four separate partitions. I (yes, this was stupid) thought the HP_TOOLS partition was probably one I could get rid of, so I deleted it and installed Ubuntu side-by-side Windows using the installation wizard, but now Windows won't progress past the loading screen without the computer automatically restarting. I've had to use Ubuntu exclusively since then. I'm not sure how I can recover it. All of my files seem to still be there--I can mount the other partition and see them, use them, etc--but Windows 7 won't boot. I really have no idea what to do or what to try, or even if I'm at a salvageable point. here's a screenshot of GParted: This makes me suspicious that it wasn't necessarily the removal of my HP_TOOLS partition but the "unknown" status of that 992.50 KiB partition there, sda1. I'm assuming that's the recovery one? How can I get Windows bootable again? I'm sorry, but I'm so unfamiliar with this sort of thing I'm not quite sure where to start.

  Read the article

• Windows 8 not shutting down properly

  - by Patrick

  Since installing Windows 8, the computer hasn't been shutting down properly. When selecting to power down, the PC quickly displays the shutting down screen, the monitor powers off, and the computer remains on but unresponsive. After about 5 minutes, the computer will turn off. Upon booting into windows again, I am informed that Windows didn't properly shut down. I'm running a fast SSD, and it's a clean install of Windows 8, so there's no way Windows is taking that time to do some sort of hibernate on shutdown or whatever - not to mention the error when entering Windows the next time. This happens on every shut down. Restart works as expected. EDIT: Formatting again didn't work. Fails regardless of drivers installed. Event viewer Always these two messages in close succession: Error (event ID 6008): The previous system shutdown at 7:45:21 PM on ?27/?10/?2012 was unexpected. Critical (kernel power, event ID 41): The system has rebooted without cleanly shutting down first. This error could be caused if the system stopped responding, crashed, or lost power unexpectedly.

  Read the article

• Can't login after upgrading to Windows 8.1

  - by flatline

  This afternoon, I upgraded my work laptop from Windows 8 to Windows 8.1. I had previously had a local account, but after the upgrade, it prompted me to enter my windows account credentials, which I had set up beforehand at some point. I entered my password and clicked next, went through another screen or two, grew tired with the process, and clicked whatever the equivalent button to "skip this step" that I was presented with. Now I can't log in. Not with my (previous) local account password, and not with my windows account password. It's a Dell with biometric identification, which I had set up previously, so I put my finger on the reader and it complained that I couldn't use that fingerprint because I had changed my password. But, I hadn't wittingly changed my password at all. I assume that what happened is that, by entering my credentials, my local account was tied to the Windows account, but because I cancelled the process partway through, something went wrong and I cannot log in. A few questions: 1) How do I log in with my windows account credentials? Should LOCALMACHINENAME\username, which was my previous login method, still work for the Windows account? When I booted to safemode it prompted me with WindowsAccount\myemailaddress, which allowed me to login there, but the regular login doesn't accept the '@' symbol. 2) Is there any way to make that account local-only again? I can't find any way of doing it. 3) I managed to enable the local administrator account and get back into the box; failing all else, is there a quick way to migrate my old profile over to a new user?

  Read the article

• What causes a switch port to receive data not destined for it?

  - by user1693454

  We are having an intermittent fault which is effecting one of our control systems on one of our HP Procurve switches. For some reason, this PLC (10mbit port - 192.168.6.56) which is attached directly to the HP Switch intermittantly start's receiving data which is not destined for it. The data is being sent from a Thecus NAS with latest firmware (192.168.6.218) to a physical IBM Server running Win2003R2 and SAP (192.168.6.225). The problem does not just send to this server, it has been to other physical servers in the past too, but always from the Thecus NAS. I am using a monitor port to wireshark what is going in/out of the PLC - normally there would be about 1mb in/out per 2 or 3 minutes - only a server asking the state of the coils. When the problem occurs, there is a flood of data being put onto the PLC line - in this captured instance, about 67mb in less than a minute. Due to this, there is no way that the PLC can be queried as the port is effectively DOSed, in turn killing part of our factory. I know that having Production on the same vlan as IT is not a good idea - I agree, however it cannot be changed at the moment (will have to wait 3 months), as well as the problem has only started happening in the last 3 months. Here is a screen cap of one of the packets being sent from the Thecus NAS which was captured from the PLC port on the HP Switch: And there are over 700 of these in this one 1024kb file. If anyone has any idea on what could be going on, some help would be greatly appreciated. If you need to know anything more, let me know! Cheers!

  Read the article

• Driver corruption when deploying Dell Touchpad Drivers (with software) during imaging process

  - by BigHomie

  We're an sccm shop, and use it to deploy Windows. When deploying Dell laptops (multiple models), the touchpad drivers seem install properly, but the software doesn't. The resulting problem is that when the touchpad is pressed on occasion, the mouse pointer will 'jump' to certain points on the screen. A possible symptom of this problem/visible sign is if the touchpad icon isn't in the system tray. The software is in the control panel, but when opened part of the gui is pixelated, indicating botched install maybe? The manual resolution to this, is to go into device manager and uninstall the driver with the option to uninstall all driver software. After a restart, the driver and software is apparently reinstalled, and from there works as expected. Obviously this partially defeats the purpose of a zero touch deployment. If anyone knows why this is and/or a possible workaround, those answers would be valid as well. Barring that, I want to find a way to deploy the driver and touchpad software in an unattended way, so that it can be conditionally installing during the imaging process. To be honest I'm not sure how to troubleshoot this, I suppose I could try drvinst.exe to install the driver, but finding out why this fails initially would keep me from spinning my wheels.

  Read the article

• Missing Memory on Windows Server 2008

  - by Chris Lively

  I have a windows 2008 x64 server with 8GB of RAM installed. Task Manager and Resource Monitor both insist that 7.5GB of the RAM is in use. However, the memory list under Processes (Memory Private Bytes) doesn't add up. I do have Show Processes from all users checked and hand adding the numbers I come up with about 3.5GB of RAM. I also looked at the latest copy of SysInternals Process Explorer. And neither the Private Bytes or Working Set adds up to more than about 3.5GB of RAM in use. What's going on? ===== Update: I bounced the server to see what would happen with the memory utilization. After boot and regular operations began it sat at 3GB of RAM usage. 18 hours later, it's back up to 6.8GB of usage with no indication as to where the additional 3.5GB or so of RAM is being used. Here are links to screen shots of the resource monitor and task manager: Resource Monitor Task Manager Update 2: Well, I believe I located the problem. When I detached one of the larger databases from my sql server the amount of ram shown as "in use" dropped drastically. The Memory Private Bytes count barely moved. So I'm guessing that SQL server has some way of allocating memory where it doesn't really show up in any of the monitors. I went further and created a new database file, then transferred all of the data from the one I detached. Even though it has the same data, and the same transactions going through it, the memory in use has stayed low. Maybe there was some corruption in the DB? I'll leave it to the DB gods and go searching for another "problem" ;)

  Read the article

• Problems reviving old pc including graphics card issue.

  - by Mick

  I have a PC that seemed to have died years ago that I am trying to revive. It has a dual core athlon processor and a gigabyte motherboard. It had two dual output graphics cards, and I have long since forgotten which output would print out the diagnostic information as the PC starts up. Also I suspect that the resolution set on all the monitors was probably higher than my current single monitor is capable of displaying. The motherboard also has a built in graphics card, so I thought it may be simplest to remove both the graphics cards and plug my monitor into the onboard graphics just while I get things going. Does that seem sensible? Now the other problem: The PC has two hard drives. I have no idea which one is the primary one it is attempting to boot from. When I power up, the fan comes on and I hear some chuga-chuga-pause chuga-chuga-pause repeat indefinitely. I'm not sure which device is making the noise. There are no-beeps at any time. I see nothing on the screen at any time, not even for a second. Any suggestions? EDIT: If T start up the PC without the power connected to the CDrom there is no chuga-chugan noise.

  Read the article

• mysql disk io keeps increasing ... is that normal?

  - by trustfundbaby

  So I've been trying to figure out this disk IO problem I have been having with my linode VPS. Over the last day or two I've just left watch -n1 pidstat -d running in a console window and the output looks like this: Monitoring it over the last few days, I've noticed that my problem lies with the init, searchd, and mysql processes. Searchd is sphinx and all its indexes are on disk, so disk io there is inevitable (apparently). What I can't understand is why the disk reads (kB_rd/s) for mysql refuse to stabilize and just keep going up. It started out at 154 yesterday and is up to what you see in that screen shot. but disk writes (kB_wr/s) have remained pretty constant the entire time. My VPS only has 768MB RAM, my mysql db has a size of about 220MB and after running mysqltuner.pl and reading a bit about it, I've been advised to set my innodb_buffer_pool_size to 220MB but I simply cannot afford to do that ... I have it up to 150MB. My question is twofold. Why does the init process have that much disk reading to do? Why is mysql doing so much disk reading?

  Read the article

• Power surge PC damage: How can I test all components of my PC without access to a second computer?

  - by Doug T.

  Ever since we had some crazy power surges last week my 64 bit Windows 7 PC has been acting strange. My USB network adapter disconnects from the wireless and can't detect the signal. I have to disable/reenable the adapter to detect it again. Also my wife has reported that the PC has rebooted a few times while I'm not sitting at it. Today I finally caught the reboot while I was using the PC. I got this blue screen of death. Stop Code 0x00000109: "Modification of system code or a critical data structure was detected." I followed the advice at the linked article and ran a memory test. I used memtest86 and its already found around 300,000 errors out of 8 gigs of ram. Now I'm worried -- what are the odds this is isolated to just my memory and not just a system wide problem? Isn't there a good chance that many other components are fried? More importantly, how can I test those other components? Are there tools similar to memtest I can use to test my motherboard/video card/power supply? If these are vender specific, is it typical for vendors to provide testing tools?

  Read the article

• Is it possible to recover from the Windows 8 refresh feature?

  - by Warren P

  The intention of the Windows 8 RTM (released version) Refresh feature is to restore the system to the way it was when I first installed. It didn't though. Almost everything that came in the start-screen (not a menu any more) is gone, not just third party apps I installed, but EVERYTHING other than the icon for internet explorer, and the icon for the store, and the desktop, were wiped. Out of the box Windows 8 had a pretty large list of things installed, and it seems that the Refresh feature wipes all of them out. Is it possible to really get the system back to a fresh install state, or should I just re-install from the DVD I made? (I have access to Windows 8 RTM, legally through the MS Action Pack subscription.) I suspect that if I create a new account, I might get a new desktop with a default set of icons, but I'm hoping it might be possible to do this without using a different login. The second problem with Windows 8 refresh is it seems to trash the ACL's on my C: drive, taking all permissions away for access to the C: drive, making nothing on it visible or readable to my primary and only login account. I believe it might be possible to undo the damage done by the "refresh" with some judicious use of icacls from the command prompt.

  Read the article

• "Windows failed to start" loop with 0xc0000225. No install discs, EasyRE/USB iso hasn't worked

  - by mvidaure

  I've been suffering from this "Windows failed to start" loop with 0xc0000225 for 3 days now and I still can't fix it. The major problem is that I don't have any sort of installation disc. However, I have tried EasyRE via both CD and USB but both result in the same problem.  I try to perform an 'Automated Repair' on my computer and I get in red text "The selected partition is corrupted and could not be accessed or repaired. Please select a different drive to continue." It is also labeled as NO under Active. Since I do not have a the installation discs, I made a USB with a Windows_7_Recovery_Disc  iso (as shown here http://www.sevenforums.com/tutorials/31541-windows-7-usb-dvd-download-tool.html) but it also doesn't work. I get a blue screen that says "RECOVERY You pc needs to be repaired. The application or operating system could not be uploaded because a required file is missing or contains errors... File:\WINDOWS\system32\winload.efi Error code: 0xc0000225 You'll need to use the recovery tools on your installation media. If you don't have any installation media, contact your system administrator or PC manufacturer." Thanks in advance! Miguel

  Read the article

• Can Windows Media Player create playlists based on folder structure?

  - by Chaulky

  Over the years I've carefully molded my digital media collection into a series of folders that make it easy for me to find what I'm looking for. I recently discovered the awesomeness that is streaming video from Windows 7 Media Player to the PS3 so I can watch it on the big screen without all the hassle of hooking the computer up to the TV. The problem is, I totally lose my carefully crafted folder structure and all my videos become one giant mess again... not cool! As a temporary solution, I've created a few playlists for my favorites (Dexter Season 4, Dexter Season 5, Breaking Bad Season 1, etc.). This is a HUGE pain in the a$$. So, is there a way to get Windows Media Player (on Windows 7) to maintain some sort of folder structure based on the location of the actual video files? So if I have my videos sorted into folders by show and season, Media Player will pick that up and let me browse it in the same way. As an alternative answer, I'll accept suggestions for a program that can also stream to PS3 and has this "folder organization" feature.

  Read the article

• mod_rewrite with AJAX applictions: possible?

  - by MrJackV

  I am trying to run Shell In a Box (link) through another server (the computer running shellinabox is not accessible from the internet) . Ideally I could use ProxyPass in the Apache config to have a reverse proxy. Problem is I can't access the conf file. So I tried using .htaccess and I discover that I cannot use ProxyPass in there. So I tried and used mod_rewrite to do the job. Currently I have the following on the .htaccess file RewriteEngine On RewriteRule ^$ http://10.1.13.236:4200/ [P] However while it displays the title correctly and if I open up the source code I can see there is something in the page, nothing is diplayed on the screen (it remains blank). My suspicion is that there are problems with AJAX and this kind of proxy. What I am trying to accomplish with the mod_rewrite as close as possible behaviour to ProxyPass (Mirorr a website in a subdirectory). Is this possible? Is there some other solution (I tried phproxy and khproxy but neither of them is able to display anything)? Thanks in advance

  Read the article

• Hibernate & Sleep broken after IE 9 RTM installation in Windows 7 x64.

  - by AKa

  I have a question about hibernation. I installed Internet Explorer 9 RTM x64 on my Windows 7 x64 SP1 desktop machine. After this, computer don't entry the hibernation or (hybrid) sleep state properly. After I hibernate the computer the monitor become blank screen and the keyboard and mouse are inactive. But the machine is still running and there isn't any possibility to switch them off as only with power button. But this is recognized on next start as ineligible because of log entry with message “The previous system shutdown at xx:xx:xx on ?xx.?xx.?x was unexpected“ and menu with safe mode option. I’m clearly not sure if it has something to do with Internet Explorer installation, but I’m definitely guaranteed that before of this I never had some problems with hibernation or (hybrid) sleep. In Windows logs isn’t something suspect. I switched the hibernation off and on, installed new drivers for mainboard, graphic and network card, checked the hard disk, nothing was helpful. This is really sad, beacuse I don't like to switch the computer completely off because it takes longer to boot. Any suggestions?

  Read the article

• vi and emacs: comparison? (not flamebait!)

  - by jared

  So, I've been enjoying learning and using vi for the last couple of years. The beauty of vi, for me, is that its UI is a language of movement and action with a very uniform, simple grammar, and which is terse enough that the requisite memorization pays ample dividends in how much more I enjoy working with text (by avoiding boring repetition and eliminating micro-hassles, like that half-second annoying wait while you scroll down the screen). (Note--I don't claim to have expert knowledge of vi, but I get around decently well: comfortable with limited '@' macros and regexp search-and-replace within files; frequently use multiple buffers, tabs, and windows; get around pretty well in the file browser; understand the grammar of actions + movement + subject (as described so aptly in this beautiful SO answer); and had some pretty sweet debugger and ctags integration going with PHP.) I wonder if some emacs folks could take a swing at explaining what emacs does brilliantly, or sum its strengths up in a phrase or two. Spare me the talk about productivity; I'm more interested in conceptual clarity. Lisp-centric answers are okay; I'm learning Scheme on the weekends, and would pick up emacs for that alone (have been using Racket).

  Read the article

< Previous Page | 575 576 577 578 579 580 581 582 583 584 585 586  | Next Page >