Search Results

Search found 28620 results on 1145 pages for 'ubuntu newb'.

Page 579/1145 | < Previous Page | 575 576 577 578 579 580 581 582 583 584 585 586  | Next Page >

• Dell M4600 with nVidia Quadro 2000M hangs on boot when external monitor is connected

  - by vladeta

  I have a problem with my fresh installed Ubuntu 12.04 LTS on my Dell M4600: nVidia quadro 2000M i7-2860 16GB ram 128GB SSD Dell/Samsung 750GB HDD IPS RGB laptop display When it is connected via DP++ to the external Dell U2311H monitor, it hangs on boot or when wakening from suspend. If I detach the DP cable it boots normally. I have tried all combinations that I have found, as adding to grub: "no splash", "boot=pci", "acpi=off", etc... I have also changed in nVidia X settings that external monitor is the primary one and also tried to delete monitor.xml file. There is no change it hangs each time after grub. It starts to load daemons then both screens are blank and then completely hangs with beep sound. What I discovered is if I detach the cable and wait for about 2 sec after grub starts booting and then physically connect DP cable while the Ubuntu is still booting everything works normally and I have a picture on my external screen while the laptop screen is off, just as I wanted. Do you maybe know how to solve this issue? Thank You.

  Read the article

• CUDA & MSI GT60 with Optimus enabled GTX670M?

  - by user1076693

  I have a MSI GT60 Laptop with an Optimus enabled GTX 670M GPU, and I have been trying to get CUDA going in Ubuntu 12.04 environment. I realize that Optimus is not supported in Linux, but I have read the following post suggesting that CUDA works for hybrid GPUs. How can I get nVidia CUDA or OpenCL working on a laptop with nVidia discrete card/Intel Integrated Graphics? I installed the NVIDIA driver via sudo add-apt-repository ppa:ubuntu-x-swat/x-updates sudo apt-get update sudo apt-get install nvidia-current The resulting driver version is 302.17, and supposedly GTX 670M is supported since 295.59. I also downloaded CUDA 4.2 from the NVIDIA site, and compiled it against nvidia-current libraries. Unfortunately, when I run deviceQuery in the CUDA SDK, I get the following output cudaGetDeviceCount returned 38 -> no CUDA-capable device is detected Checking /proc/driver/nvidia/gpus/0/information gives the following Model: GeForce GTX 670M IRQ: 16 GPU UUID: GPU-????????-????-????-????-???????????? Video BIOS: ??.??.??.??.?? Bus Type: PCI-E DMA Size: 32 bits DMA Mask: 0xffffffffff Bus Location: 0000:01.00.0 Here is the output of "lspci | grep VGA" 00:02.0 VGA compatible controller: Intel Corporation Ivy Bridge Graphics Controller (rev 09) 01:00.0 VGA compatible controller: NVIDIA Corporation Device 1213 (rev ff) So... what am I doing wrong? Thanks!

  Read the article

• Gparted funkiness - won't recognize 1TB, full-hdd /home partition, but recognizes ext4 and /home label

  - by Kurtosis

  I have a 1TB SATA hard disk from my old desktop, and the entire thing is an ext4 /home partition (/, /boot, and swap were all on another hdd). It is now in a USB2 enclosure and I want to use it to back up my current laptop /home. To do this I need to shrink the /home partition on the 1TB backup drive. It only uses about 500GB so that shouldn't be a problem, I'll start the laptop with an Ubuntu live USB, plug in the 1TB drive, and use Gparted to shrink the 1TB /home partition to ~500GB. Then I can create a second partition in the newly freed space, and cp -ax my laptop's /home over to it. Unfortuntely, Ubuntu Live USB can detect and mount the external hdd, and Gparted can see it's there, but Gparted can't read it and hence can't resize it. Disk Utility reports the drive is fine, no errors, so I'm not sure what's the problem. See linked pics, worth a thousand words. Anyone know what the problem is here? Any pointers in the right direction much appreciated.

  Read the article

• wget has a 4 second delay

  - by guisius

  Hello. I have tried to wget a page with windows/mac, and the response is instant while the linux vesion needs to wait for 4 seconds before it shows the response. I just hope this can be solved. More information added: in Ubuntu : wget xxx://192.168.0.135/test.cgi?cmd= -O test.txt --2011-03-04 14:21:17-- xxx://192.168.0.135/test.cgi?cmd= Connecting to 192.168.0.135:80... connected. HTTP request sent, awaiting response... 200 OK Length: unspecified [text/html] Saving to: `test.txt' [ <=> ] 17 --.-K/s in 0s 2011-03-04 14:21:22 (1.88 MB/s) - `test.txt' saved [17] while in Mac OS : wget xxx://192.168.0.135/test.cgi?cmd= -O test.txt --2011-03-04 14:22:33-- xxx://192.168.0.135/test.cgi?cmd= Connecting to 192.168.0.135:80... connected. HTTP request sent, awaiting response... 200 OK Length: unspecified [text/html] Saving to: `test.txt' [ <=> ] 17 --.-K/s in 0s 2011-03-04 14:22:33 (755 KB/s) - `test.txt' saved [17] in ubuntu it delays 4 seconds while windows and mac will not i believe it may related to some setting in the network config such as packet size , window frame , but i have no idea to set this PS: because the limit of the post not allow to post the url so i mark this as xxx

  Read the article

• Cannot enable Additional drivers for Broadcom in 12.10

  - by Compt

  tl;dr version: Additional Drivers does not work for enabling a driver in Ubuntu 12.10, however it worked in 12.04. I upgraded to Ubuntu 12.10 from 12.04 via a live USB. I did a fresh install to avoid any conflicts. From 12.04 I know that my wireless card has proprietary drivers that could be installed via Additional Drivers. I did eventually find additional drivers in the software sources menu, however when I attempt to switch to Broadcom 802.11 Linux STA wireless driver source from bcmwl-kernel-source, it not only does not work, it in fact disables my wireless completely. The only way to revert this is to restart, and revert back to "do not use the device". Then upon another restart, my wireless will function once again. I was curious if anyone else had this issue, and if there was a fix for it as of yet. I looked on launchpad and it may be a potential bug, but I am unsure. Any help would be greatly appreciated (and sorry for that wall of text). Until then, I'll continue to use my wireless as it is (or revert to 12.04), but I do notice a slower connection without it enabled.

  Read the article

• crippling repeating "pciehp card not present" notifications

  - by Nanne

  When using ubuntu (12.04, both installed and on a live usb) I get a lot of these messages: pciehp 0000:00:1c.5:pcie04: Card not present on Slot(37) pciehp 0000:00:1c.5:pcie04: Card present on Slot(37) And with a lot I mean about 20 per second. This has a crippling effect, and I would like to get rid of it :) The computer is a packard bell easynote BG48-U-100 DC. I tip I picked up from some fedora/redhat error here was to look at lspci -vnn. I have pasted the part about "00:1c.5" here: http://pastebin.com/0sfsiqW2 For what good it may do, here is the lsmod of my machine: http://pastebin.com/DQZy1kAL From that first pastebin I think to conclude that it has to do with the module shpchp, which seems to me (aka: google) to have something to do with ACPI. That's as far as I've come in disecting this. Can anyone help me along further? What can I do, check etc? I did see this topic but my intentions are not to surpress the error message: I know how to do this (from that topic ;) ), but I'm looking for a real sollution. Finding the problem on the internet does suspect me to believe it is neither an ubuntu specific nor a packard-bell specific problem.If you google the problem it seems that is present on several other distribution/hardware combo's as well, and it looks like the advice is to remove one of the drivers? I have no clue as to which driver I should look at and and what would be the effect of just removing it. I have seen this topic which is old-ish, but describes my problem and is about a similar computer. The solution in this topic was to compile a new kernel using a spanish guide, which seems a bit extreme to me, so I'm kinda hoping for a better solution than that.

  Read the article

• Ugly Boot Screen after upgrading to 12.10

  - by Sir Linuxalot

  Is there a way to change the ugly boot screen in 12.10? It seems to have rolled back to that 8-bit blocky looking thing with tiny orange dots underneath. It then breaks into process code under that, and it looks ghastly. I've read some tutorials on getting Plymouth to do some neat things, but they were for older versions of Ubuntu. I'm running a GeForce GTX 460 if that matters. Any help would be appreciated. Update: I've noticed/found a couple of things. The upgrade on my laptop didn't do this. It still uses the "normal" Ubuntu boot logo (using Plymouth, I assume). So, something is off with my desktop. And, I found and installed Super Boot Manager to see if that would help. With that, I enabled Plymouth and added a new theme, but the machine still boots with the block-ugly logo. Finally, I messed around with Grub on boot and added "nomodeset" after "quiet splash" and added it while deleting "quiet splash." None of these solutions worked. I'll keep hunting...

  Read the article

• UDF Partition reported full when it is not

  - by Capt.Nemo

  I was using these instructions to setup an external hard disk with udf. I have been able to setup a multi-partition system using those instructions, but I seem to have hit a wall, where the partition is reported as full while writing to the disk. Every other tool available to me reports it as free. Relevant lshw output Here's a screenshot showing the disk: Both the output of df and the file manager (caja) report the disk as free. Filesystem Size Used Avail Use% Mounted on /dev/sda9 9.0G 7.6G 910M 90% / udev 974M 12K 974M 1% /dev /dev/sda1 50G 47G 295M 100% /media/Data /dev/sda6 49G 41G 5.9G 88% /home /dev/sda2 155G 127G 29G 82% /media/Entertainment /dev/sda8 14G 13G 516M 96% /media/Stuff /dev/sdb2 120G 1.9G 112G 2% /media/3c887659-5676-4946-875b-b797be508ce7 /dev/sdb3 11G 2.6G 7.7G 25% /media/108b0a1d-fd1a-4f38-b1c6-4ad1a20e34a3 /dev/sdb1 802G 34G 768G 5% /media/disk I seem to have hit a wall near the 35GB mark. Despite being shown as 35gb/860gb used everywhere, the following happens on a write attempt: [2017][/media/Dory]$ echo D>>echo bash: echo: write error: No space left on device Writing byte by byte, the maximum I can take it to is 34719248K. The most weird part is that on mounting it Windows, Windows can write to the disk easily, and the writes are being read fine back in Ubuntu. However, the used-bytes remains at 34719248K in Ubuntu (It goes higher on Windows, however).

  Read the article

• Routing tables don't show ppp0 after 12.04 kernel upgrade to 3.5.0: Haier CE682 modem configuration

  - by ubunsteve

  I'm trying to get my Haier CE682 EVDO modem, model number 201e:1022 to work in ubuntu 12.04 kernel 3.5.0-030500-generic #201207211835 . I had it working in a previous 12.04 kernel, using compat-wireless and these instructions http://zulkhamsyahmh.blogspot.com/2012/05/install-smartfren-haier-ce682-on-ubuntu.html, and to get it working had to edit the routing tables so that there was a ppp0 showing up, as suggested at http://www.linuxquestions.org/questions/slackware-14/wvdial-is-connecting-but-im-unable-to-do-anything-714861/ Network manager doesn't work with this modem, so I use either wvdial or gpppon to connect to it, both which work (after I run the command sudo modprobe usbserial vendor=0x201e product=0x1022 ) This is the output of when I connect with gpppon to the modem: Using interface ppp0 Connect: ppp0 <-- /dev/ttyUSB0 sent [LCP ConfReq id=0x1 ] rcvd [LCP ConfAck id=0x1 ] rcvd [LCP ConfReq id=0x2 ] sent [LCP ConfAck id=0x2 ] sent [LCP EchoReq id=0x0 magic=0x819c86db] rcvd [CHAP Challenge id=0x1 <1ac8f12799e953967a3cc222c9254690, name = ""] sent [CHAP Response id=0x1 <6f12a903dc40915ca2761c17b87f8fbd, name = "smart"] rcvd [LCP EchoRep id=0x0 magic=0x0] rcvd [CHAP Success id=0x1 ""] CHAP authentication succeeded CHAP authentication succeeded sent [CCP ConfReq id=0x1 ] sent [IPCP ConfReq id=0x1 ] rcvd [IPCP ConfReq id=0x1 ] sent [IPCP ConfAck id=0x1 ] rcvd [CCP ConfReq id=0x1] sent [CCP ConfAck id=0x1] rcvd [CCP ConfRej id=0x1 ] sent [CCP ConfReq id=0x2] rcvd [IPCP ConfRej id=0x1 ] sent [IPCP ConfReq id=0x2 ] rcvd [CCP ConfAck id=0x2] rcvd [IPCP ConfNak id=0x2 ] sent [IPCP ConfReq id=0x3 ] rcvd [IPCP ConfAck id=0x3 ] not replacing existing default route via 192.168.3.1 local IP address 10.191.248.154 remote IP address 10.17.95.25 primary DNS address 10.17.3.244 secondary DNS address 10.17.3.245 as you can see there is a problem with "not replacing existing default route via 192.168.3.1" This it the out put of route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default 192.168.3.1 0.0.0.0 UG 0 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 192.168.3.0 * 255.255.255.0 U 2 0 0 wlan0 I had tried these commands, which had previously worked in the earlier kernel: route del default route add default ppp0 but that broke my wireless internet connection. I then added the default routing as shown above with sudo route add default gw 192.168.3.1 wlan0 So it seems I need to add or change the routing to show a ppp0 connection, but I don't know how to do that.

  Read the article

• How to force Multiple Monitors correct resolutions for LightDM?

  - by Hanynowsky

  I am affected by the BUG: https://bugs.launchpad.net/ubuntu/+source/unity-greeter/+bug/874241 Otherwise, if like me you have a laptop connected to a second monitor of higher resolution, LIGHTDM at the login stage, mirrors the displays in both screens and assign to them a common resolution (1024X768) in my case, instead of extending the desktop (Primary screen with the greeter and secondary with just a logo as mentioned in the Multiple Monitors UX specifications book for 12.04). Here is my xrandr -q @L502X:~$ xrandr -q Screen 0: minimum 320 x 200, current 1920 x 1848, maximum 8192 x 8192 LVDS1 connected 1366x768+309+1080 (normal left inverted right x axis y axis) 344mm x 193mm 1366x768 60.0*+ 1360x768 59.8 60.0 1024x768 60.0 800x600 60.3 56.2 640x480 59.9 VGA1 disconnected (normal left inverted right x axis y axis) HDMI1 connected 1920x1080+0+0 (normal left inverted right x axis y axis) 510mm x 287mm 1920x1080 60.0*+ 1600x1200 60.0 1680x1050 60.0 1280x1024 60.0 1440x900 59.9 1280x960 60.0 1280x800 59.8 1024x768 60.0 800x600 60.3 56.2 640x480 60.0 DP1 disconnected (normal left inverted right x axis y axis) I tried to force lightdm to execute some xrandr commands in order to set the right resolution for each monitor and extend the desktop, but I get a LOW GRAPHICS MODE ERROR (You're running in low graphics mode, your screen, input devices...did not get detected..) I created a simple script named lightdmxrand.sh: #!/bin/sh xrandr --output HDMI1 --primary --mode 1920x1080 --output LVDS1 --mode 1366x768 --below HDMI1 And told lightdm to run it : /etc/lightdm/lightdm.conf [SeatDefaults] greeter-session=unity-greeter user-session=ubuntu greeter-setup-script=/usr/bin/numlockx on display-setup-script=/home/hanynowsky/lightdmxrandr.sh Someone knows what is wrong!? Thanks in advance.

  Read the article

• Launcher icons are invisible after upgrade from 11.10 to 12.04

  - by Clo Knibbe

  I am re-purposing an old laptop. I installed 11.10 on it and then immediately upgraded to 12.04. (I could not directly install 12.04 as my system does not support PAE.) When my system was (briefly) 11.10, the desktop appeared as expected. However, after the upgrade to 12.04, the icons in the launcher area are invisible. If I hover over the spot where the icon should be the little popup window showing the tool's name appears, and I can click to invoke the tool. I just cannot see the icons. ![invisible icons in launcher][1] The icons do appear as expected in other contexts, for example in the Home folder and in Dash Home. My theme is "Ambiance (default)" I do not have a ~/.icons folder. This is the top level contents of /usr/share/icons: default DMZ-Black DMZ-White gnome handhelds hicolor HighContrast HighContrastInverse Humanity Humanity-Dark locolor LoginIcons LowContrast redglass ubuntu-mono-dark ubuntu-mono-light unity-icon-theme whiteglass (Sorry for the poor formatting, can't get it to show in list.) I suspect that the launcher isn't looking for the icons in the right place, but I don't know how to confirm that, or how to correct. This is my first foray into Linux, although I used to use Unix a few decades ago. This doesn't look much like my old Sun workstation, though! Does anyone have any suggestions or insights for me? Thanks.

  Read the article

• Connect to NFS on availability

  - by berkes

  What would be a good way to automatically mount an NFS when it gets/is available? I have the following: Media server at home, running Ubuntu, 10.10 with GUI *) Laptop often at home, often on the road or at clients. Ubuntu 10.10 with GUI. What I'd like is my laptop connecting to the nfs (or any other mountable networked filesystem) so that Banshee sees all the music, new podcast-entries (and video) from that media-server. I already have firefly (mt-daapd) running, which works, but is flakey on both server-side and client-side. But its biggest downside, is that I cannot easily fix metadata on files on the media-server this way. DAAP is read-only by design. I can mount nfs manually, through a sudo mount /media/nfsmultimedia/. I am not looking for a manual, or howto on setting up a NFS client and server. Merely a way to have this more transparently working. Obviously I'd like the NFS to be unmounted if the network is no longer available (i.e. when I open my laptop-lid on my clients buro). It may be, that an NFS is not suited for this, in that case, I'd love to hear other options. :) *) Actually: I also have a fileserver, backupserver and webserver to which I'd like to connect in a somewhat similar way. Right now I connect to these over SSH, using gvfs.

  Read the article

• Thinkpad W510 with default graphics drivers shows weird brightness issues

  - by Chantz

  Hey guys, I am currently running 10.10 - 32 bit on a new Thinkpad W510 with nVidia Quadro FX 880M graphics card. I am running with the default graphics drivers that installed with ubuntu install. My problem is that when I am logging in the screen acts normally as far as birghtness is concerned. I can increase/decrease brightness with Fn keys. But few seconds after I log in screen goes pitch dark. Hitting Fn+Home flickers the screen to all the way bright, then all the way dark. This behavior continues until I reach maximum brightness, in which case the screen stays all the way bright, for a few more seconds and then again goes dark if there is no activity & the cycle continues. Have you guys faced any of these issues? If so any pointers on how to resolve it. I am not alone, on ubuntu forum I saw another person having the same issue - link but no solution. Please help! UPDATE I followed the instructions that htorque mentions in his answer and it worked.

  Read the article

• How to help FGLRX detect a device

  - by user113416

  I have HD 4850 card, Ubuntu 12.10 and installed legacy drivers using makson96 ppa. The issue is, that FGLRX can not detect my device and loads vesa bios. I had the same problem on ubuntu 11.10, 12.04 versions. I want to manually help fglrx find a matching device to load as it shoudld do. It is interesting, why does fglrx search for a device in a PCI:0@1:0:1 Bus? in xorg.cof different bus is indicated: Section "Device" Identifier "aticonfig-Device[0]-0" Driver "fglrx" BusID "PCI:1:0:0" EndSection fglrxinfo display: :0.0 screen: 0 OpenGL vendor string: Advanced Micro Devices, Inc. OpenGL renderer string: ATI Radeon HD 4800 Series OpenGL version string: 3.3.11653 Compatibility Profile Context Here is a part of my xorg log: [ 3.846] (II) VESA: driver for VESA chipsets: vesa [ 3.846] (II) FBDEV: driver for framebuffer: fbdev [ 3.846] (++) using VT number 7 [ 3.846] (WW) Falling back to old probe method for fglrx [ 3.883] (II) Loading PCS database from /etc/ati/amdpcsdb [ 3.883] (--) Assigning device section with no busID to primary device [ 3.883] (--) Chipset Supported AMD Graphics Processor (0x9442) found [ 3.884] (WW) fglrx: No matching Device section for instance (BusID PCI:0@1:0:1) found [ 3.884] (II) AMD Video driver is running on a device belonging to a group targeted for this release [ 3.884] (II) AMD Video driver is signed [ 3.884] (II) fglrx(0): pEnt->device->identifier=0xb7791d8f [ 3.884] (WW) Falling back to old probe method for vesa [ 3.884] (WW) Falling back to old probe method for fbdev Thanks in advance.

  Read the article

• Printer share keeps asking for password and I can't authenticate from any machine. Why?

  - by tenshimsm

  Ubuntu 12.04 printer share keeps asking for password and I can't authenticate from any machine. Why?? We've installed it in two machine (to act as printer servers) and we get the same problem. It doesn't matter what we do, change or install. We can't figure out why the printer share asks for password even using all of the users that are registered in the server. What is wrong with Precise? I want it to work without a password, but it is not even working WITH one! I gave up! The samba version that comes with Precise is insufferable! I tried various settings that didn't work. I should've used Mint from the beginning. [Edit] My printers config. Remembering that samba is 3.6.3 in ubuntu 12.04 load printers = yes [printers] comment = All Printers browseable = yes path = /var/spool/samba printable = yes guest ok = yes readonly = yes create mask = 0700 [print$] comment = Printer Drivers path = /var/lib/samba/printers browseable = yes readonly = yes guest ok = yes

  Read the article

• Why doesn't unity show icons or panel after installing numix theme?

  - by Sid

  I'm a beginner to Ubuntu/Linux and I have a problem: Unity is not loading! When I choose Unity in the log-in screen, I get notifications and I can see the mouse, but that's it. I have Ubuntu 14.04 installed, along with Bumblebee/Primus. I had no issues whatsoever, until I decided to try the numix-theme and the numix icon pack. I added the PPA and installed it, but when I logged off and logged back on, nothing showed up. I panicked, and in tty1, I purged numix-* but that did not solve the issue. To get by day-to-day use, I installed gnome-flashback, and among those environments, only the metacity one works. (The compiz one does not.) I've tried installing the unity-tweak-tool to reset unit, installing dconf and doing: dconf reset -f /org/compiz/ but that didn't work either. One site even told me to delete /org/compiz/, but that did not resolve the issue. When I checked ccsm, the Unity plugin had a check to it. I also tried with Unity doesn't load, no Launcher, no Dash appears, but it gets stuck on "loading icons". Any help will be awesome!

  Read the article

• How can I make multiple displays work on my Asus UX32VD?

  - by oKtosiTe

  Original title: Why do I have two trash icons in the Unity Launcher? Whether I run Ubuntu as a live-USB or install it, I always have two trash bins on the Unity Launcher. Both work, and both open the same location. This seems a bit redundant; what could be done about it? Update: Turning auto-hide on made it obvious that I have multiple Launchers showing. With auto-hide off, they simply overlap, making it look like there's a double trash icon, but with auto-hide enabled, I can display one Launcher (and therefore one trash icon) at a time. Still, two are running simultaneously. Second update: This problem appears to be caused by the way Ubuntu handles multiple displays on my Asus UX32VD Ultrabook. Somehow, the laptop display cannot be used while my external display is connected. It is shown in the Displays list, but remains black no matter how I configure it. The external display runs at 1920x1200, the laptop monitor should run at 1920x1080. It therefore becomes obvious that the Launcher that's supposed to run on the laptop display, is actually displayed on the external monitor. Using nomodeset as a kernel parameter as indicated here makes the laptop display inaccessible altogether, detecting the external monitor as the laptop display and making resolutions other than 1920x1200 inaccessible. That is not an option.

  Read the article

• Issues with Cinnamon?

  - by Corrodie

  I just recently switched my system over to Ubuntu 12.10, and decided on Cinnamon as my environment-- it all worked fine, at first. But I was poorly educated and started using Compiz and Emerald along with it--Setting both as replacements in startup processes. I now know, that's a big, big mistake. Now when loading Cinnamon, I am greeted to my background image, and only that. My only options seem to be to open a terminal. I was advised to attempt muffin --replace and mutter --replace Neither to any avail, the terminal closes, and I cannot load another one unless I completely reload. I went back to Unity, purged and autoremoved Cinnamon, emerald, and compizconfig, and attempted to reinstall Cinnamon, thinking that would solve the problem--no, it came back just as broken as before. So, I reinstalled ubuntu, then cinnamon---still broken. I'm assuming I must find a way to remove the replace commands-- but as I have no menu, I'm not positive I can do that. Is there any way I can access the startup processes via terminal? I'd think though, if I completely removed Cinnamon, all configurations would be gone too, so, it's just not making much sense. Is there some kind of reset I could possibly do? I've been browsing forums and questions here, all leading to things I'd already done, so, it can't hurt to ask for myself. I apologize if you would rather I have posted this over at mint. Next time, I will definitely check compatibility instead of assuming something just has to work. Any help is greatly appreciated, thanks! ****EDIT***** It seems although it didn't allow me to do it before, I was now allowed to access the settings and startup processes for Cinnamon via Unity, and, after quickly removing aforementioned processes- I'm up and running again.

  Read the article

• Bizarre SSH Problem - It won't even start

  - by thallium85

  I recently got Ubuntu 12.04 Precise, got it up and running with some MediaWiki software, static IP on the box and router and was able to access the main page even from a cell phone. Everything seemed great... Then I wanted to finally get rid of the monitor and keyboard and login remotely via SSH. I installed openssh-server, let everything point to port 22 for a test run and installed putty on my Windows XP machine. I got a connection refused. Went back and started checking the Ubuntu install itself... (I'm under root from this point on) $ sudo -s $ service ssh status ssh stop/waiting $ service ssh start ssh start/running, process 2212 $ service ssh status ssh stop/waiting Apparently ssh has stopped or is waiting for something.... $ ssh localhost ssh: connect to host localhost port 22: Connection refused I can't even connect to myself... I checked ufw (firewall) to see if port 22 is doing alright... $ sudo ufw status Status: active To Action From 22 ALLOW Anywhere 22/tcp ALLOW Anywhere 22 ALLOW Anywhere (v6) 22/tcp ALLOW Anywhere (v6) sshd_config shows only Port 22 Is ssh not using the right IP address at all? I just don't get what I did wrong here. When this is up and running I will def change the port number, but for now, I don't want to mess with the default install too much until a test run with putty is successful. Edit: Here are my sshd_config file and my ssh_config file. The command /usr/sbin/sshd -p 22 -D -d -e returns: /etc/ssh/sshd_config line 159: Subsystem 'sftp' already defined. Edit: @phoibus moving the sshd_config file and reinstalling did the trick! service ssh status the above command shows that ssh is now running and I am now able to log in from my windows xp computer remotely via putty. Thanks so much! I can now use my monitor for other things!

  Read the article

• 12.10 upgrade broke brightness keys [closed]

  - by Chris Morgan

  I have been running Ubuntu (64-bit) on my HP 6710b laptop (Core 2 Duo with integrated graphics) for several years, and the backlight brightness keys have always worked. Since I upgraded to Ubuntu 12.10 earlier today, those keys do not work any more. The secondary function keys: Fn+F3: sleep; still works (and considerably faster than ever before!) Fn+F8: battery info; still works Fn+F9: reduce brightness; stopped working in 12.10 Fn+F10: increase brightness; stopped working in 12.10 It may also be worth while mentioning that X does not appear to be receiving the brightness events at all, or at least not sending them out further. (This I detected with a key logger I wrote for a Uni project, which uses X's Record extension; it is informed of the sleep and battery info keystrokes, but doesn't receive the brightness ones at all.) In the mean time, I know that I can use the Brightness & Lock settings screen to alter the brightness. (Wow! I can suddenly make my backlight darker than I could before—I can go right down to turning the backlight off, something I couldn't do before... but this model has a fairly dim screen, so I don't expect to use that much, if ever.) How can I get the brightness keys working again? This question is probably strongly related to I can't control my Brightness in HP Compaq 6710s.

  Read the article

• Blurry printed raster images with Brother MFC-8840D

  - by Adam Monsen

  (NOTE: crossposted here: ubuntuforums.org/showthread.php?t=1621795) I've got a Brother MFC-8840D. Works great with Ubuntu server! Setting up a CUPS print server was pretty straightforward, and I also finally got network scanning working reliably with saned. Printing documents and Web pages works well: fonts are crisp/clear, etc. One issue has got me completely vexed: printing raster (ie: JPG) images. They are blurry. For example, I can scan a page of black and white text at 150 or 300 dpi. The grayscale image looks perfect on my monitor. But the printed version is much blurrier than the original, regardless of the "print resolution" dpi I choose. As a counterexample, if I use the "copy" function of the MFC-8840D, the copy looks excellent, and this function is much, much faster than if I scan then print a scan of same. I've googled around a bunch and tried different tricks (printing a PDF with the image from evince, printing with Gimp, EOG and other applications) but I just can't print anything that looks as good as a copy made with the MFC-8840D. Any ideas? I'm using Ubuntu 10.04.1 LTS server. I'm using the PPD file from solutions.brother.com. Thanks, -Adam

  Read the article

• Memory limiting solutions for greedy applications that can crash OS?

  - by Hooked

  I use my computer for scientific programming. It has a healthy 8GB of RAM and 12GB of swap space. Often, as my problems have gotten larger, I exceed all of the available RAM. Rather than crashing (which would be preferred), it seems Ubuntu starts loading everything into swap, including Unity and any open terminals. If I don't catch a run-away program in time, there is nothing I can do but wait - it takes 4-5 minutes to switch to a command prompt eg. Ctrl-Alt-F2 where I can kill the offending process. Since my own stupidity is out of scope of this forum, how can I prevent Ubuntu from crashing via thrashing when I use up all of the available memory from a single offending program? At-home experiment*! Open a terminal, launch python and if you have numpy installed try this: >>> import numpy >>> [numpy.zeros((10**4, 10**4)) for _ in xrange(50)] * Warning: may have adverse effects, monitor the process via iotop or top to kill it in time. If not, I'll see you after your reboot.

  Read the article

• Problem with dpkg-preconfigure, how to correct?

  - by Eric Wilson

  I was trying to install TeamViewer, and I followed the instructions here even though they specify 11.10 instead of 12.04 (what I'm running). In particular, I executed. $ wget http://www.teamviewer.com/download/teamviewer_linux.deb $ sudo dpkg -i teamviewer_linux.deb The dpkg command failed, and after this point my packaging system has been broken. The software center instructs me to try: $ sudo apt-get -f install which leads to Reading package lists... Done Building dependency tree Reading state information... Done Correcting dependencies... Done The following packages will be REMOVED: teamviewer7:i386 0 upgraded, 0 newly installed, 1 to remove and 17 not upgraded. 9 not fully installed or removed. Need to get 89.0 kB of archives. After this operation, 81.9 MB disk space will be freed. Do you want to continue [Y/n]? y Get:1 http://us.archive.ubuntu.com/ubuntu/ precise/main dash amd64 0.5.7-2ubuntu2 [89.0 kB] Fetched 89.0 kB in 1s (83.9 kB/s) E: Sub-process /usr/sbin/dpkg-preconfigure --apt || true returned an error code (100) E: Failure running script /usr/sbin/dpkg-preconfigure --apt || true At this point I'm stumped.

  Read the article

• How system services are started in 12.10?

  - by Salem

  One thing that always confused me in Ubuntu was how system services are started. I know that Ubuntu uses Upstart and supports SysV, but which one is used to start the services? This matters when you want a "manual" start for a service. For example, on my system i have files for the following services either in /etc/init.d/<service> (Upstart) and /etc/init/<service>.conf (SysV): acpid, mysql, networking, qemu-kvm, ufw, libvirt-bin So if i want to disable MySQL execution at startup, i must use the Upstart way or the SysV way to disable it? Also, how can i tell which of those is really used to start a generic service? Edit The really doubt here is not how disable/enable services using SysV/Upstart. What really confuses me is that some services seem to be defined (and enabled) in SysV and Upstart at the same time. Is there any precedence between them (like if mysql is enabled in both launch it using SysV)? Or can it be the case that one tool uses the other in background?

  Read the article

• How do I mount a CIFS share via FSTAB and give full RW to Guest

  - by Kendor

  I want to create a Public folder that has full RW access. The problem with my configuration is that Windows users have no issues as guests (they can RW and Delete), my Ubuntu client can't do the same. We can only write and read, but not create or delete. Here is the my smb.conf from my server: [global] workgroup = WORKGROUP netbios name = FILESERVER server string = TurnKey FileServer os level = 20 security = user map to guest = Bad Password passdb backend = tdbsam null passwords = yes admin users = root encrypt passwords = true obey pam restrictions = yes pam password change = yes unix password sync = yes passwd program = /usr/bin/passwd %u passwd chat = *Enter\snew\s*\spassword:* %n\n *Retype\snew\s*\spassword:* %n\n *password\supdated\ssuccessfully* . add user script = /usr/sbin/useradd -m '%u' -g users -G users delete user script = /usr/sbin/userdel -r '%u' add group script = /usr/sbin/groupadd '%g' delete group script = /usr/sbin/groupdel '%g' add user to group script = /usr/sbin/usermod -G '%g' '%u' guest account = nobody syslog = 0 log file = /var/log/samba/samba.log max log size = 1000 wins support = yes dns proxy = no socket options = TCP_NODELAY panic action = /usr/share/samba/panic-action %d [homes] comment = Home Directory browseable = no read only = no valid users = %S [storage] create mask = 0777 directory mask = 0777 browseable = yes comment = Public Share writeable = yes public = yes path = /srv/storage The following FSTAB entry doesn't yield full R/W access to the share. //192.168.0.5/storage /media/myname/TK-Public/ cifs rw 0 0 This doesn't work either //192.168.0.5/storage /media/myname/TK-Public/ cifs rw,guest,iocharset=utf8,file_mode=0777,dir_mode=0777,noperm 0 0 Using the following location in Nemo/Nautilus w/o the Share being mounted does work: smb://192.168.0.5/storage/ Extra info. I just noticed that if I copy a file to the share after mounting, my Ubuntu client immediately make "nobody" be the owner, and the group "no group" has read and write, with everyone else as read-only. What am I doing wrong?

  Read the article

< Previous Page | 575 576 577 578 579 580 581 582 583 584 585 586  | Next Page >