Search Results

Search found 74454 results on 2979 pages for 'hardware problem'.

Page 580/2979 | < Previous Page | 576 577 578 579 580 581 582 583 584 585 586 587  | Next Page >

• Error while trying to dual boot Ubuntu alongside Windows 8

  - by Brian

  I recently purchased a new Toshiba Ultrabook that comes pre-installed with Windows 8. I'm trying to dual boot 12.10 with it and I have run into a problem with the installer. When I get to the page to pick the partitions I get this: No drives are listed and the only thing in that device drop down is /dev/sda. If I click Install Now or +/-/change I get an "Ubuntu has stopped working" error message. I'm trying to install off a 12.10 64-bit USB drive in UEFI mode, and I have tried it with secure boot both enabled and disabled with the same results. The hard drive set up is as follows: 500 GB main drive windows recovery (primary) EFI boot section (primary) Windows' partion (280 GB I believe) (primary) unallocated space I created for Ubuntu partition (200ish GB) another Windows recovery partition (primary) 12 GB solid state drive all unallocated space Could it be a problem with the number of primary partitions? I think I read somewhere about a max of 4.

  Read the article

• how to find available wireless networks

  - by Quinn

  I'm using an HP Pavilion dv6000 I've looked at other answers similar to this question how ever when I look at my network symbol it doesn't say anything that the answer below says "Make sure that your wifi hardware switch is on or not. It is either F2 or F12 or near to it. Once the switch is enabled, there is a small fan-like applet on the top panel (Gnome Network Manager), fourth from the right. Click on it and if there is no tick mark on the option 'Enable Wireless', enable it. Wait till your wifi connection name appears." it how says 'Enable Networking' my wi-fi switch is on and I've tried using terminal to kill the applet as another answer suggests trying. Does anyone have any other ideas that might help? Just in case anybodies curious as to how I'm posting this I'm on my other ubuntu laptop that's running an older version.

  Read the article

• Can only connect to file server on second attempt

  - by Ross Fleming

  I have a FreeNas file server on my local network and I usually connect to it from Windows and Ubuntu computers. Ever since I have upgraded from Ubuntu 12.04 to 12.10 Ubuntu will only connect after a second attempt. By which I mean, I will browse to it via the file manager and once I click on the link in "Bookmarks" it complains that it could not connect. If I then try again it connects successfully and will keep up it's connection until the laptop is suspended or looses connection to the LAN for whatever reason. This isn't much of a problem as I don't mind having to click twice but my real problem is that this means that my scheduled backup will complain that it cannot connect to the storage device if it has not already been accessed during the current session. If there is some way to either stop the issue all together or to force the backup tool (default) to immediately have a second attempt at connecting.

  Read the article

• The entire content of my Wordpress page has disappeared

  - by John Catterfeld

  I have a blog installed on my site using Wordpress. Last week I upgraded Wordpress from 2.6 to 3.0.4 (I had to do this manually). All went well, or so I thought, but I have just noticed that the content of an existing page has vanished. The page URL still works, but all content has disappeared - doctype, html tags, body tags, everything. Please note, this is specific to pages - posts are still displaying fine. I have since created a brand new page which does not display the content either. Things I have tried include Switching to a freshly installed theme Deactivating all plugins Setting the problem page to draft, and back again Deleting the .htaccess file I suspect it's a database problem and have contacted my hosting company who have said the only thing they can do is restore the DB from a backup, but that I should consider it a last resort. Does anyone have any further ideas what to try?

  Read the article

• Oracle VM Moves into Challenger Position in the Latest Gartner Magic Quadrant

  - by Monica Kumar

  Oracle Innovations boost Oracle VM into Challenger Position in Gartner x86 Server Virtualization Infrastructure Magic Quadrant Oracle VM's placement in the just published Gartner x86 Server Virtualization Infrastructure Magic Quadrant affirms the Oracle strategy and is also supported by strong customer momentum gains. Optimizations delivered in Oracle VM releases during this last year along with easy software access and low cost licensing have moved Oracle’s placement into the Challenger quadrant in a very short time. Oracle continues to focus on delivering a strong integrated virtualization with Oracle VM and the managed stack in the following areas: Integrated management with Oracle VM and all layers of the Oracle stack from hardware to virtualization to cloud Application-Driven virtualization with Oracle VM templates for rapid enterprise application deployment Certified Oracle applications on Oracle VM Complete stack solution offering more values to customers Get a copy of the Magic Quadrant for x86 Server Virtualization Infrastructure report to read more about how Oracle VM rapidly moved up in its new position.

  Read the article

• cannot add movie file to pitivi

  - by niku

  when i try adding this movie file to pitivie i get the error as follows (i can play the file in mplayer just fine tho): Problem: An internal error occurred while analyzing this file: Could not find GStreamer caps mapping for FFmpeg codec 'h264', and you are using an external libavcodec. This is most likely due to a packaging problem and/or libavcodec having been upgraded to a version that is not compatible with this version of gstreamer-ffmpeg. Make sure your gstreamer-ffmpeg and libavcodec packages come from the same source/repository. Extra information: gstffmpegdec.c(1336): gst_ffmpegdec_negotiate (): /GstPipeline:Discoverer-file:///media/Data/pitivi/taw2.mkv/GstDecodeBin2:dbin/ffdec_h264:ffdec_h2645 Also, my system language is English, but regional format is set to German. mplayer installed in German, I want it in English tho... Thanks a lot for your help :) I know I'm a noob .

  Read the article

• Video crashes with 10.10

  - by John Mahon

  I have installed both the 64bit and 32 bit versions of 10.10 on my Compaq Presario PC. I first installed the 64 bit version of the OS.The video often crashed when switching user. It also went haywire occasionally when I visited some web-sites. I read that there may be some problems with the 64 bit OS. So I installed the 32 bit version on another disk. This version seemed even less well behaved. HP's model number for the computer is SR1838NX. The hardware is listed at http://bizsupport1.austin.hp.com/bizsupport/TechSupport/Document.jsp?objectID=c00628274&lang=en&cc=us&contentType=SupportFAQ&prodSeriesId=1841793&prodTypeId=12454&printver=true#A0 I think the important info is that the chip set is "ATI Radeon Xpress 200" and the processor is "Athlon 64 (S) 3700+ 2.2 GHz" Has anyone else had video problems with similar machines? Is there a work around or an update? I have had previous versions of Ubuntu working on this machine and other flavors of Linux as well. Thanks in advance. John

  Read the article

• ATI graphics card, with gnome shell on Ubuntu 11.10, screen flickers

  - by bioShark

  After installing gnome shell, without any problem, after log in the fonts are missing and it looks like crap...nothing is readable. Don't want to make it a double post, because my issue is similar to the one from this question but for me the problems have not been solved properly. After running the commands from that post, and installing the latest AMD 11.10 driver, the Gnome shell display issues have been solved. But each time I move the mouse in the upper left corner, to bring up the applications...my entire screen flickers. Without the applications been displayed, everything looks fine. Hardware: ATI HD4870, Intel Q6600.

  Read the article

• Hadoop, NOSQL, and the Relational Model

  - by Phil Factor

  (Guest Editorial for the IT Pro/SysAdmin Newsletter)Whereas Relational Databases fit the world of commerce like a glove, it is useless to pretend that they are a perfect fit for all human endeavours. Although, with SQL Server, we’ve made great strides with indexing text, in processing spatial data and processing markup, there is still a problem in dealing efficiently with large volumes of ephemeral semi-structured data. Key-value stores such as Cassandra, Project Voldemort, and Riak are of great value for ephemeral data, and seem of equal value as a data-feed that provides aggregations to an RDBMS. However, the Document databases such as MongoDB and CouchDB are ideal for semi-structured data for which no fixed schema exists; analytics and logging are obvious examples. NoSQL products, such as MongoDB, tackle the semi-structured data problem with panache. MongoDB is designed with a simple document-oriented data model that scales horizontally across multiple servers. It doesn’t impose a schema, and relies on the application to enforce the data structure. This is another take on the old ‘EAV’ problem (where you don’t know in advance all the attributes of a particular entity) It uses a clever replica set design that allows automatic failover, and uses journaling for data durability. It allows indexing and ad-hoc querying. However, for SQL Server users, the obvious choice for handling semi-structured data is Apache Hadoop. There will soon be an ODBC Driver for Apache Hive .and an Add-in for Excel. Additionally, there are now two Hadoop-based connectors for SQL Server; the Apache Hadoop connector for SQL Server 2008 R2, and the SQL Server Parallel Data Warehouse (PDW) connector. We can connect to Hadoop process the semi-structured data and then store it in SQL Server. For one steeped in the culture of Relational SQL Databases, I might be expected to throw up my hands in the air in a gesture of contempt for a technology that was, judging by the overblown journalism on the subject, about to make my own profession as archaic as the Saggar makers bottom knocker (a potter’s assistant who helped the saggar maker to make the bottom of the saggar by placing clay in a metal hoop and bashing it). However, on the contrary, I find that I'm delighted with the advances made by the NoSQL databases in the past few years. Having the flow of ideas from the NoSQL providers will knock any trace of complacency out of the providers of Relational Databases and inspire them into back-fitting some features, such as horizontal scaling, with sharding and automatic failover into SQL-based RDBMSs. It will do the breed a power of good to benefit from all this lateral thinking.

  Read the article

• Revisiting restoring database after disabling TDE and removing the certificate

  - by MartinBell

  I thought I would re-visit the problem of removing a certificate after disabling TDE...(read more)

  Read the article

• Sound fails when I switch users

  - by Sam

  Sound on my computer was working fine under 12.04 however when I upgraded to 12.10 I have encounter a strange problem where when I switch users instead of the first user having its sound swamped the sound of the first user keep playing and the second user can not play and thing. The sound setting for the second user only show a Dummy Output. If I reboot and log into the second user sound works fine but then if you switch to the first user it has a dummy output instead. What could would cause such a problem?

  Read the article

• How do I stop Ubuntu Precise freezing/hanging

  - by artfulrobot

  At least once a day I lose work on my (2 different) Intel i5 machines running Ubuntu 12.04. The entire system will freeze/lock-up/hang, and never return. At this point nothing works; even the caps lock key doesn't toggle the light on the keyboard; Ctrl-Alt-F1 won't do anything either. askubuntu.com is apparently where I'm directed for support. I suspect this is a kernel bug. But I simply can't keep losing work like this, so I'm anxious to try whatever it takes to get the thing reliably working. Can you suggest something I can try to fix the problem an existing bug I can follow progress on and contribute to (from users/tester's POV) the most constructive way I can contribute to helping fix the problem, keeping in mind that I do need the computer (so can't do things that might "brick" it!)

  Read the article

• HP 510 laptop doesn't suspend when I close the lid

  - by Yuri

  I have an HP 510 laptop with Ubuntu 12.04. I have all the correct settings for suspending when the lid is closed, as far as I can tell, so I think it's a problem with detecting the event. The way it "should" be detected, from what I can see, is a little hardware switch that is pushed when the lid closes. This switch manually puts off the backlight, and sends the suspend signal. All I can think is that the signal isn't being properly interpreted. Can anyone suggest a fix? Update: I tested whether the button was actually working based on the suggestion by josinalvo, and I found that in the directory /proc/acpi/button/lid/ there is no LID directory. There is, however, a C1CF folder, and in it is a state file. When using the this file instead of ID, I discovered that, no, when I close the lid, the state does not change.

  Read the article

• Get Trained in Sun ZFS Storage 7000 Appliance

  - by mseika

  Oracle University has scheduled the following OPN Only course: Course: Sun ZFS Storage 7000 Appliance Installation, Administration & Hands-On Lab Dates: 23-27 Jun 2014 11-15 Aug 2014 6-10 Oct 2014 Location: Reading You will learn how to successfully describe, install, configure, maintain, administer, troubleshoot and upgrade Sun ZFS Storage 7000 software and hardware. There is a hands-on lab which will take you through a NAS head software restore session, often referred to as a FISHSTICK restore. More details and online registration Remember: your OPN discount will be applied to the standard price shown on Oracle University web pages. For assistance in booking and more information, contact the Oracle University Service Desk: eMail: [email protected] Telephone: 01 189 249 066

  Read the article

• Infrared usb adapter not hot pluggable?

  - by A. Goossens

  For transferring exercise files from my Polar heart rate monitor i use the software Protrainer 5 with an external infrared usb adapter. Using Wine to run Protrainer 5 and some adjustments mentioned here (using irda-utils) i managed to make it work. Well, sort of: every time i want to transfer exercise files and the adapter is not plugged in i have to reboot my laptop with the usb adapter plugged in to make it work. Since i have a laptop it unfortunately is no option to just always leave the adapter in. It seems to me that the usb adapter isn't hot pluggable (which seems odd for a usb device) or there must be another problem. Polar WebLink (other software to transfer exercise files) experiences the same issue. Can anyone help me to fix this problem? Infrared usb adapter: Polar IRDA USB adapter OS: Ubuntu 12.10 (64-bit) Hardware: Lenovo Thinkpad T500

  Read the article

• Programmatically adding metatags to Masterpages in Web Forms and MVC [migrated]

  - by Mike Clarke

  Has anyone got any ideas on where we should be adding our SEO metadata in a Web Forms project? Why I ask is that currently I have two main Masterpages, one is the home page and the other one is every other page, they both have the same metadata that’s just a generic description and set of key words about my site. The problem with that is search engines are only picking up my home page and my own search engine displays the same title and description for all results. The other problem is the site is predominantly dynamic so if you type in a search for beach which is a major categories on the site you get 10000 results that all go to different information but all look like a link to the same page to the user. edit It's live here www.themorningtonpeninsula.com

  Read the article

• Where to find algorithms work?

  - by Misha

  The funnest parts of my projects have been the back-end algorithms work. I have worked on projects where I implemented Gaussian Mixture models, a Remez algorithm and a few Monte Carlo schemes. I loved figuring out how these processes worked and tuning them when they didn't. I recently graduated and my problem lies in the work I was able to find. The only jobs I have found, with my Electrical Engineering degree, are for writing user applications. Tasks such as fashioning web interfaces or front-ends for hardware devices. When I speak with potential employers about my interests they say they have no work of the sort. Where does one find work that involves implementing these kind of schemes?

  Read the article

• Virtualbox will run from 32bit installation CD but not 64bit.

  - by MetaDark

  I am trying to set up Windows in Virtual Box, so I don't need to reboot in the rare occasion that I actually need it. The problem is, Virtual Box doesn't preform any errors when I insert the 32bit installation CD but when I try to use the 64bit installation; What!? I am already using the installation disc! I've checked my BIOS to see if I have SVM (AMD's version of VT) disabled and all I see is "Enabled" I have a K9N6PGM2-V2 motherboard A Triple Core AMD Athlon II A Nvdia NForce 430 integrated graphics card 4GB of RAM An 80GB IDE And a 1TB SATA I don't think the last three specifications matter but just in case XP I am pretty sure the CD isn't broken ( I am going to make sure in just a moment ), what could be the cause to this problem? Edit: The 64bit installation CD is not broken, but I found out when trying to install from the 32bit version that it's trying to upgrade, not preform a fresh install - Odd.

  Read the article

• No HDMI sound output on Thinkpad X1

  - by nickf

  I'm having problems getting my sound to output via HDMI to my TV. When I go to Sound Settings, the HDMI device does not appear. ~$ aplay -l **** List of PLAYBACK Hardware Devices **** card 0: PCH [HDA Intel PCH], device 0: CONEXANT Analog [CONEXANT Analog] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: PCH [HDA Intel PCH], device 3: HDMI 0 [HDMI 0] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: PCH [HDA Intel PCH], device 7: HDMI 1 [HDMI 1] Subdevices: 1/1 Subdevice #0: subdevice #0 card 0: PCH [HDA Intel PCH], device 8: HDMI 2 [HDMI 2] Subdevices: 1/1 Subdevice #0: subdevice #0 I don't know if the video information is helpful, but anyway: ~$ sudo lshw -C video *-display description: VGA compatible controller product: 2nd Generation Core Processor Family Integrated Graphics Controller vendor: Intel Corporation physical id: 2 bus info: pci@0000:00:02.0 version: 09 width: 64 bits clock: 33MHz capabilities: msi pm vga_controller bus_master cap_list rom configuration: driver=i915 latency=0 resources: irq:46 memory:d0000000-d03fffff memory:c0000000-cfffffff ioport:5000(size=64) Any suggestions for me?

  Read the article

• How do I fool 12.10 to think it uses Unity2d in order to get the resolution my screen can use?

  - by Konstapel Kask

  On a laptop (model older) I have two screens (one built in, one external). I wish to use them both at the same time, but the settings app complains: Requested size (2944, 1080) exceeds 3D hardware limit (2048, 2048). You must either rearrange the displays so that they fit within a (2048, 2048) square or select the Ubuntu 2D session at login. The problem though, Unity 2D has been discontinued. I have forced Ubuntu to render Unity in 2D mode (with the help of echo export UNITY_LOW_GFX_MODE=1 >> .xprofile in accordance to this askubuntu post. But the error message still remains. How can one get the resolution that my computer supports? Or, how can I assure Ubuntu that it truly does use a 2D session?

  Read the article

• Unity iOS optimization and draw calls

  - by vzm

  I am curious of what methods I should approach in optimizing my Unity project for iOS hardware. I have very little image effects running (directional light with low res shadows) and I used the combine children script from the standard assets to lessen the load on the CPU. My project currently runs with 45-57 draw calls at non-intensive segments and up to 178 at intensive segments. I heard that static batching relieves some of the stress, but the game has the environment moving around the player instead of the player moving around the environment. Is there any alternative that I may look towards to improving the draw call number?

  Read the article

• What's a good starting point to learn about JIT compilers?

  - by davidk01

  I've spent the past few months learning about stack based virtual machines, parsers, compilers, and some elementary things about hardware architecture. I've also written a few parsers and compilers for C like languages to understand the generic parser/compiler pipeline. Now I'd like to take my understanding further by learning about optimizing compilers and JIT compilers but I'm having a hard time finding material at the right level. I don't yet understand enough to dive into a code base like PyPy or LuaJIT but I also know more than what most introductory compiler books have to offer. So what are some good books for an intermediate beginner like to me to look into?

  Read the article

• Flash player (in Firefox) is unstable in 14.04

  - by henry

  For 13.10, I used this guide to get Intel iGPU-supported playback of flash videos in Firefox: http://www.webupd8.org/2013/09/adobe-flash-player-hardware.html All in all, Intel graphics acceleration for flash content was working just fine in 13.10, at least on my machine (with Xubuntu). I basically followed the guide to do the same for 14.04, but about 2-3 weeks ago flash videos started acting up. Whenever I have one instance of flash paused or stopped in one tab and go to the next tab to continue some song on Soundcloud or something, it's game over. I'm clueless as to what I can do here. Did anything change in the meantime?

  Read the article

• How to merge two .iso images

  - by pgrytdal

  I am following this tutorial to install Android onto my computer VIA Virtual Box. My problem is, they want you to download liveandroidv0.3.iso.001 liveandroidv0.3.iso.002 then they want you to merge these two files with cat liveandroidv0.3.iso.001 liveandroidv0.3.iso.002 > liveandroidv0.3.iso in the Terminal. The problem is, when I run the command, I get the following output cat liveandroidv0.3.iso.001 liveandroidv0.3.iso.002 > liveandroidv0.3.iso cat: liveandroidv0.3.iso.001: No such file or directory cat: liveandroidv0.3.iso.002: No such file or directory So, I was wondering if there was an alternative way to merge these files? Or if you guy's could help me merge them this way? Extra info: OS: Ubuntu 12.10 I downloaded the files to my /downloads folder in my home directory.

  Read the article

• Why can't I copy files to var/www/html?

  - by Alaa M.

  I copy some files, go to /var/www/html, right click, Paste isn't available. Why is that? I tried the command sudo nautilus, it opened the files navigation window, I navigated to /html, still the same problem. I also tried gksudo nautilus but it said: The program 'gksudo' is currently not installed. You can install it by typing: sudo apt-get install gksu I installed it, tried again, same problem. What should I do? edit: Figures that I was accessing the files inside a .zip directory and I shoulda extracted them first. Solved

  Read the article

< Previous Page | 576 577 578 579 580 581 582 583 584 585 586 587  | Next Page >