Search Results

Search found 28828 results on 1154 pages for 'i heart ubuntu'.

Page 583/1154 | < Previous Page | 579 580 581 582 583 584 585 586 587 588 589 590  | Next Page >

• Totem crashes immediately after startup in 12.10

  - by Sakib Hasan

  I did a fresh install of Ubuntu 12.10 and did sudo apt-get update && sudo apt-get update. Then I installed ubuntu-restricted-extras, audacious and vlc from Software Center. After that I tried launch Totem Movie player but in terminal following error comes up: (totem:9295): Gdk-ERROR **: The program 'totem' received an X Window System error. This probably reflects a bug in the program. The error was 'BadDrawable (invalid Pixmap or Window parameter)'. (Details: serial 1808 error_code 9 request_code 152 minor_code 9) (Note to programmers: normally, X errors are reported asynchronously; that is, you will receive the error a while after causing it. To debug your program, run it with the GDK_SYNCHRONIZE environment variable to change this behavior. You can then get a meaningful backtrace from your debugger if you break on the gdk_x_error() function.) Trace/breakpoint trap (core dumped) I tried purge and again install. But the error remains. What should I do?

  Read the article

• Kubuntu 11.10 Lot of Networking problems

  - by Cobraone

  Since I upgrade to 11.10 I have a lot of problems with KDE. First of all there are problems in configuring a static IP address. Just to explain @home I have a normal fiber ADSL and I use a DHCP. When I go to a customer I must insert a static IP address. With ifconfig everything seems ok but there is something wrong in searching DNS names. (I have installed Ubuntu and was going ok again). Now I Have reinstalled again Kubuntu 11.10 and I have the same problem in addition today I have discovered that if I connect to a network in another customer office the desktop freezes and I could only switch between windows with alt+tab. No FN key or right click to open run command works. So i unplugged network (configuration is just DHCP here) and tried on another position in office. It was the same. My Laptop freezes when connected, a fedora 14 of a friend works. So I decided to connect my Galaxy S II as USB network device. Everything is ok for like 3 minutes. When I noticed a little loss of signal again the desktop freezes and i must work (like now) just switching between windows with alt+tab). Additional information: Unplugging network or restarting it via Konsole does not not solve the freezing problem. Every time I must open a console and reboot. Any idea of what tests to do ? Just a recommendation: If I must post here logs or something else please guide me. I use Linux since Ubuntu 9 but I am not an "expert".

  Read the article

• How can I have sound output before logging in?

  - by ??O?????

  I have a machine (Ubuntu 11.10) that I would like to have it play audio (typically through an amplifier), but the machine should be headless (where its final placement will be). I will control what is played through ssh. However, there is no sound output until I login to the graphical console. At first I thought it was an issue with pulseaudio, so I promptly removed it to use the default ALSA, but I have the same issues. I ssh to the machine, I run alsamixer and get the typical cannot open mixer: No such file or directory error (while /proc/asound/cards display correctly what I have). If I login on the graphical console, alsamixer works fine in the ssh session, and I have sound output. I logout, and then alsamixer stops working. So something runs (Xsession perhaps?) when I login that enables sound output, and gets disabled when I logout. I remember in older versions of Ubuntu, there was a drum roll when the machine showed the login screen; that is not the case anymore. Perhaps if I somehow can enable that drum roll, I'll have fixed my problem too. In any case, the question I ask is what the title says.

  Read the article

• No keyboard after suspend, even after hard reset

  - by subatomics

  all. While I was using a Ubuntu 9.1 live CD, I put the computer (Toshiba Satellite C655) into standby. After I resumed, the keyboard stopped functioning, though the mouse (USB) still worked. I decided to turn off the computer, but after Ubuntu shuts down, it asks you to press "enter" to actually turn the machine off. The keyboard was still dead, so I all I could do was use the on/off switch to power down the computer. Now, when I try to boot the computer, nothing happens. Before this problem, I would see a menu asking me to select an OS (I had Windows 7 and Windows XP installed). I cannot use any emergency measures because I need to press F12 to boot from a CD, and the keyboard is still not working. I tried removing the HD to force a boot from the CD, but it didn't work. I also tried to plug in a USB keyboard, which failed as well. Right now, I have no idea how to fix this. Any ideas? Thanks.

  Read the article

• Can't log-in anymore

  - by Awake Zoldiek

  I installed Ubuntu x64 12.04 Desktop LTS on my new laptop three days ago. Of course when I installed it I did an "apt-get upgrade" and a "apt-get update". I modified the .bashrc file to add some aliases but that's about it. Everything went fine I think, but this morning when I tried to connect to my user account, it just simply didn't work. Even when I give the right password, it will send me to a black screen with a few text lines written in white for a second and then back to the log-in screen. When I logged into the guest session, I couldn't shutdown / restart. I tried the "rm /home/MyUsername/.Xauthority" solution after doing a Ctrl + Alt + F1 at the log-in screen. But that didn't work. Does anyone has an idea ? My Ubuntu seems to use Gnome. Thank you a lot in advance ! This question is similar to this one, but their solution didn't help : -- after 12.04 upgrade: can't log in although password is correct

  Read the article

• What credentials should I use to access a Windows share?

  - by JMCF125

  H
  i, I have installed Samba and CIFS and all that, followed a bunch of tutorials, but still I can't access a share in the separate Windows 7 machine. Before I could access a share in Ubuntu from Windows, but although now I can't for whatever reason; the error of the attempt to mount the Windows share is the same: 13, asking for credentials (the computer with Windows is off now, but I can add the exact error message later). In /etc/fstab I have: # ... (help info) ... # <file system> <mount point> <type> <options> <dump> <pass> # ... (mounting points that don't matter for the question) ... //192.168.1.2/C\:/Users/Public/Documents /srv/Z\:/ cifs user=guest,password=,uid=1000,iocharset=utf8 0 0 I also tried options such as username=guest,uid=1000,iocharset=utf8 and guest,uid=1000,iocharset=utf8, which, of course, don't work. What user am I supposed to use? (user=user; username=user; my credentials in the Windows and Ubuntu machines do not work, at least with the syntax I tried - similar to this). Even if this worked it's not actually what I want. I wanted to setup an authentication for any one trying to access the drive (it's currently 777, for the Linux share as well) and put a limit/quota on the share's use (as I see Z:on Windows, it allows for the entire C:drive to be filled). Thank you in advance. I'd be glad if you suggested a way to do this even without the last paragraph.

  Read the article

• How to modify partitions after install?

  - by ChocoDeveloper

  I wanted to have Ubuntu with full disk encryption on one big partition, and Windows on a small one. In 12.04, only the Server Edition installer has full disk encryption, so I used that and then installed ubuntu-desktop. When it asked for the size, I reduced it from ~999GB to ~750gb. Now after the install, on both gparted and disk utility I see /dev/sda2 taking ~931GB, and nothing unallocated, so I can't create a partition for windows. I got the size right, because when I right-click inside a folder, then hit 'properties', I see Free space: ~690GB (I don't know why it's not ~750GB, but at least it's not 900). The command df -h shows the same. So what can I do? Normally I would just resize a partition with gparted to create unallocated space, then create the partition. But here I have two problems: gparted does not seem to be showing the correct values, and also it says it does not support LUKS so I'm afraid it will mess things up. Any thoughts?

  Read the article

• How to troubleshoot GPU freezes?

  - by dlsmith2

  So in advance I'll just say I am a total linux newbie, so be kind. I just downloaded Ubuntu 11.10 and this is my first experience with Linux. I enjoy it so far and actually enjoy it except for when my computer freezes. This has been quite often so far. I've done a little research and it seems my problem is with the GPU. When it does freeze I can move the cursor but cannot click on anything. I also cannot run Alt+F2 xkill. So my only previous experience has been with Windows and I would normally solve an issue like this with Ctrl+Alt+Delete and just shut down the offending program. I do not know how to do this in Ubuntu and not even sure this would even work. Please help me if you can, how do I deal with a freeze without having to resort to a hard shutdown, I cannot seem to run the computer over one hour without experiencing this issue. I tried accessing my GRUB menu on startup but I can't even seem to do that. Also the only real program I have been running whenever this happens seems to be Firefox. Thank you, appreciate any help. After running lspci | grep VGA command prompt: 00:12.0 VGA compatible controller: nVidia Corporation C67 [GeForce 7150M / nForce 630M] (rev a2)*****

  Read the article

• When trying to install Wine on 12.10, 'Sudo' command will not let me type in a password.

  - by Nocturnus

  As the title explains, I have been attempting to install Wine on my laptop which is running 12.10. When I access the command terminal and entered "sudo add-apt-repository ppa:ubuntu-wine/ppa" I was of course met by a password block, when I attempted to enter my password, it flat out wouldn't let me type anything, the only key that got a response from the terminal was "enter" which was met by "incorrect password". To bypass this issue I backed out and used the 'Gksudo' command, this new dialogue box seemed to give me access to sudo commands. I then entered "sudo apt-get update" and "sudo apt-get install wine1.5". Up until the installation everything went fine, but after entering the final command (still using gksudo) The terminal read "the following packages have unmet dependencies" and proceeded to list a bunch of "recommends" So my guess is that Wine hasn't been updated to run on 12.10... Is this true, and is there any other way to open .exe's? Also what was with that funky password misshap? I'm totally new to Ubuntu so I've just been using support pages and tutorials, sorry if I'm a bit naive in these matters...

  Read the article

• error/message: the disk drive for /home is not ready... when connecting an external hard drive

  - by seallussus

  i am running Ubuntu 10.04 all updated installed to date (3/28/2012) and when i connect another sata HD i get this message the disk drive for /home is not ready yet or not present continue to wait, or press S to skip mounting or M for manual recovery so i press S but i get this message could not update ICEauthority file /home/username/.ICEauthority And when a press close i get this there is a problem with the configuration server (/usr/libconf2-4/gconf-sanity-check-2 exited with status 256) And when a press close i get message Nautilus could not create the following required folders :/home/username/desktop,/home/username/.Nautilus before running Nautilus, please create these folders or set permissons such that Nautilus can reach them And finally when a press Ok at the last message it disappears and i get a blank screen with a lot of colors on it and with nothing else so i shutdown (power button ) and disconnect the HD and boot without problems so how to fix this in simple commands because i am a total Linux noob notes -In the original error my username was in place of username i wrote (did not want to confuse anybody ) -I tried searching for this problem but a got a lot of different answers and most of them were really complicated to me and not working -I got a data HD connected and working without problems also the HD i installed Ubuntu on is Sata (maybe it helps) -Apologize for me bad English its not my mother language

  Read the article

• Twitter "Authentication Error" Turpial & Choqok (latest versions)

  - by PineMarten

  I use Turpial a lot, but Turpial isn't connecting at all. I can still connect to Twitter thru the OS app (no issues signing in through Online Accounts) and of course I can still sign in using the browser, but Turpial gives me an "Authentication Error" and Choqok fails to do anything. I've tried changing my password, revoking the Turpial and Ubuntu apps in Twitter and re-enabling them, but then it gives me an "Invalid Credentials" message. I've even removed and installed Turpial multiple times, still nothing. I can't find any information or resources for this type of error from Turpial online. I think it may be something recent after finding this message elsewhere: (article related to "Birdie") It looks promising i'm currently using it atm, since all the other twitter clients no longer work due to the API 1.0 shutdown (posted today) I've never used Choqok before today, so I don't even know if I've set it up properly. It's failing to retrieve or send Tweets it just blank screens, but at least it signs in. I've figured that this isn't an issue with Ubuntu, or Turpial or Choqok, or the router (already replaced it today), so I don't really know what I'm dealing with here. I hope it's not another API issue, Facebook did something similar just a few weeks ago

  Read the article

• Am I running out of memory or do I have two logical drives instead of one

  - by user30904

  I did a complete reinstall of Ubuntu 13.04 a couple of months ago. Since then, I have switched out my motherboard with another. I kept the same hard drive. I just did an upgrade to 13.10. Recently, after this install, I keep getting the message that I'm running out of memory. I just checked my system usage and was surprised by what I found. I believed that I installed Ubuntu as a fresh install but when I check the system usage, it seems like there are two logical drives. I just did the basic install, so I was only expecting to see one partition but instead I see two. One is a small 300mb partition, the other is a 300gb partition I was expecting. Can anyone tell me if I have two partitions and/or logical drives and if so how I can fix this? I seem to have been running on the smaller drive and now I'm obviously out of space. I want to be able to use the bigger one at least.

  Read the article

• How to solve Fatal error: Call to undefined function readline()? readline library not found?

  - by SirBT

  I have an Ubuntu 12.04 LTS. And XAMPP for linux 1.7.7. When I code in php with and call the readline function I get this error message? "Fatal error: Call to undefined function readline()" I recently found the below thread which pointed out the name of the package that contained the desired readline: How to solve configure: error: readline library not found? I went ahead and installed # apt-get install libreadline6. But this didnt seem to make a difference. I still get the same error message: "Fatal error: Call to undefined function readline()". Was the thread missing further steps? Can anyone help me? I am new to Ubuntu. <?php echo "Simple menu \n" ; echo "1. Play Sports \n"; echo "2. Play Strategy games \n"; $userInput = readline('Enter something here: '); ?>

  Read the article

• How to Install Broadcom Wireless Drivers (BCM43xx)

  - by Fer1805

  I'm having serious problems installing the Broadcom drivers for Ubuntu. It worked perfectly on my previous version, but now, it is impossible. I'm a user with no advance knowledge in Linux, so I would need clear explanations on make, compile, etc. Edit: For the command: "lspci | grep Network", I get the following message: 06:00.0 Network controller: Broadcom Corporation BCM4311 802.11b/g WLAN (rev 01) For the command: iwconfig, i get the following: lo no wireless extensions. eth0 no wireless extensions. When i follow the following steps (from the above link), there are a NO error message at all: open the 'Synaptic Package Manager' and search for bcm uninstall the bcm-kernel-source package make sure that the firmware-b43-installer and the b43-fwcutter packages are installed type into terminal: cat /etc/modprobe.d/* | egrep '8180|acx|at76|ath|b43|bcm|CX|eth|ipw|irmware|isl|lbtf|orinoco|ndiswrapper|NPE|p54|prism|rtl|rt2|rt3|rt6|rt7|witch|wl' (you may want to copy this) and see if the term blacklist bcm43xx is there if it is, type cd /etc/modprobe.d/ and then sudo gedit blacklist.conf put a # in front of the line: blacklist bcm43xx then save the file (I was getting error messages in the terminal about not being able to save, but it actually did save properly). reboot 'End of procedure' Before (not ubuntu 11.04), if i wanted to connect wireles, i just went to the icon at the upper side of the screen, click, showed ALL the wireless network available, and done. Now, the only options i see are: Wired Network Auto Eth0 Disconnect VPN Enable networking Connection information Edit connection. lspci -vnn | grep Network showed: Broadcom Corporation BCM4322 802.11a/b/g/n Wireless LAN Controller [14e4:432b] hope above info is enough for your help.

  Read the article

• External monitor on old Dell 700m?

  - by Adam Henne

  Okay, linux noob. I installed 10.04 on an old Dell 700m in hopes of using it as a media center device. That seems to work great, except now it won't output to the external monitor. VGA cable works fine, TV recognizes other computers fine, it's the laptop that won't output. Turns out that the 700m, unlike every other computer out there, doesn't have a Fn hotkey to switch monitors. The only way to do it in Windows was to go through the Control Panel. In Ubuntu, though, the Monitor setup won't detect or recognize any monitors. The laptop display works fine, but I can't adjust or add anything. I did a little research and found suggestions for older Ubuntu builds involving the xorg.conf. I tried one out, in spite of my unfamiliarity, and it's screwed the whole display big time. I can fix that with a clean reinstall, that's no problem, but I'm cautious about editing xorg again. Any suggestions? Thank you!

  Read the article

• Crackling sound from microphone recently, in 13.04

  - by Patrig Droumaguet

  I use 13.04 since the release and I use Skype which was working well. But recently I've had remarks saying my voice was "crackling", even if the voice from my interlocutor was perfect. Making a test with Audacity and Cheese, I've seen that every recorded sound (with the front microphone of my laptop or a jack microphone) was crackling. It's not really like saturating, the sound has a lot of annoying pops. I've tried to check the settings, they were still on PulseAudio. I've even tried the extreme solution : re-installing Ubuntu (because initially it was working)… with the same problem. If I boot on Windows (dual-boot) I have no problem (so it's not physical). If anyone could help :) My laptop is a HP dv6-6165sf. The sound card is a "IDT 92HD81B1X5" (with BeatsAudio). Thanks a lot ! New tests - july 6th Hi again, I've tried editing /etc/pulse/default.pa with these three settings : load-module module-udev-detect use_ucm=0 tsched=0 load-module module-udev-detect tsched=0 load-module module-udev-detect use_ucm=0 The three of them don't change anything, except the last one (which was by default) which makes Audacity record without any crackling sound. But in Skype, Cheese and Kazam, the sound is crackling… I've installed again Ubuntu 13.04 (from scratch, deleting everything from /home), and I've updated it. The microphone is still cracking. Thanks for your help !

  Read the article

• How do I prevent software packages from being downloaded until I know it's safe?

  - by Dave M G

  Recently, an update that caused a problem with Gnome session caused me to lose a day's work. The solution was to rollback some packages to a previous version. The update manager is now telling me that my old packages should be updated: ... but I don't want to do that until I know that whatever bug or problem the latest version has is resolved. I understand that with any upgrade that there is a risk of instability. However, in the 8 years or more that I've been on Ubuntu, using the latest releases has been stable enough and with the benefit of the latest features and security. So, I'm not looking for general advice on how to handle upgrades. What I'm saying is that in this one particular instance, the bug introduced by these upgrades is severe and time wasting. But, as an end user, when I encounter a problem like this, I have no idea how to address a specific concern about a specific package. I don't, for example, know which of these packages is the problem, and I can't take time from my work schedule to be experimenting with each package. So, my question is: How do I find out who exactly is responsible for these, or any, packages so that I can contact them and let them know about the problem? How do I freeze these packages only, but allow other upgrades to happen? ubuntu-session gnome-session-common gnome-session-bin gnome-session

  Read the article

• how do I uninstall old kernel options listed in Grub2? [closed]

  - by user12809

  Possible Duplicate: Is there a way to remove/hide old kernel versions? I installed Ubuntu Tweak in Ubuntu 11.10, went to Janitor, and selected and removed old kernels that appeared there (3.0.0-12). Now, the only installed linux-image that appears as 'Installed' in SPM is the most recent one (3.0.0-13), which is the one I want. It did not however eliminate the kernel listing in Grub 2. At boot: However, at boot, in Grub-2, the following options still appear: 3.0.0-13-generic 3.0.0-13-generic (recovery mode) 3.0.0-12 (generic) (on /dev/sde5) 3.0.0-12 (generic (recovery mode) (on /dev/sde5) And, in Terminal, when I change directory (cd) to /boot, and then list (ls), I get the following listed kernels: 3.0.0-13 2.6.38-12 2.6.38-8 (al There is no change when I sudo update-grub in Terminal 1) what is /dev/sde5, and where is it located in the file system, so i can delete it? 2) why the differences between what appears as installed in SPM, what appears at boot in Grub2, and what shows when I list the contents of Grub2 in Terminal? Ultimately, I simply want to remove the 3.0.0-12 kernel options at boot in Grub2. How do I best and simplest do that? Thanks again donofrij is online now Report Post Edit/Delete Message Reply With Quote Multi-Quote This Message Quick reply to this message

  Read the article

• Wifi interface changes name seemingly at random

  - by ray_voelker

  I'm currently having some issues getting a wireless interface to work continuously under an install of Ubuntu 12.04.1 LTS. Some of the issues I'm experiencing include Connection will drop out after some time after it has initially worked. Interface will be a different name after a reboot. For example, wlan0 will become wlan4 when using the ifconfig -a command. Ubuntu will take a long time to boot, looking for network adapters. The purpose of this build is to function as a web kiosk in a library. The computer is supposed to boot up into a web browser, and allow for browsing of the catalog. For some reason this interface does not appear to be working as it should. Are there any explanations for some of these problems I'm having, and perhaps some solutions? The wireless card appears as this after doing an lspci ... Ralink corp. RT2561/RT61 802.11g PCI In the /etc/network/interfaces file I have the following configuration for the interface. auto wlan0 iface wlan0 inet dhcp wireless-essid UDwireless wireless-mode Managed Thanks in advance for help on this.

  Read the article

• Kubuntu never gets to the login screen

  - by searchfgold6789

  I am not sure if Xorg is using the right device... The system in question is an A4-1400 CPU with built-in Radeon Graphics. I added a PCIe Radeon HD 5750, and changed the BIOS so it would use that card automatically. Now it appears that I can see output from the TV plugged into the HDMI port, and boot into recovery mode, but cannot get to a desktop - X doesn't start. It just freezes at the Kubuntu splash screen. I have no idea how to get X to use the proper graphics card. I pasted the Xorg.log to http://paste.ubuntu.com/6261137/. And the Xorg.conf generated by aticonfig --initial is at http://paste.ubuntu.com/6261161/ Also, see lspci and lshw -c display outputs. I can provide more information, but something does tell me X is not using the right graphics card and I've no idea where to begin how to fix it... I faced a similar issue before with another distribution but found no information anywhere on how to make X use a specific graphics card. Or maybe it's not that simple.

  Read the article

• Broadcom 4313 doesn't work following 12.04 upgrade

  - by Lucas

  I have an hp G62-228Ca laptop with a BCM4313 previously running Ubuntu 11.10. I ran the 12.04 upgrade last night without much thought. Following the upgrade and mandatory reboot, the wireless card no longer shows up in the network manager, the first time I've had any kind of issues with wireless under Ubuntu. I've done much Googling on the issue but so far I haven't found a permanent solution. Mucking around with some packages though (I've installed five different ones or so), I've managed to devise a workaround that I must run every time I boot the laptop. I have to remove the Broadcom STA driver and reinstall it. Inspiration taken from here: WiFi does not work, Broadcom STA Wireless driver does not work on a BCM4313 After the second modprobe command, the wireless reappears in the network manager and ten seconds after that I'm back on the wifi. If anyone can provide some advice on how to fix this permanently I will be extremely grateful. I'd rather not roll back to 11.10 or reinstall, but I will if I need to. Just let me know if you need the output from any terminal commands. Thanks in advance!

  Read the article

• How do I add a boot from cd option to yaboot?

  - by Sergiu

  So I'm dual-booting Ubuntu 12.04.1 on my iMac G5 powepc alongside Mac OS X and I want to add a boot cd option to yaboot because I'm trying to boot a scratched Mac OS X installation DVD that takes a while to read and the frst bootstrap moves on too fast. How do I edit the timeout for the first bootstrap anyways? So, my main question is, how do I add a cd booting option to yaboot and then, how doI boot it? The devalias from OpenFrmware tells me that 1 have 2 cd-rom instaled, on is /ht/pci@3/ata-6/disk@0 and the other on ends with a 1 instead of a zero. These are the contents of my yaboot.conf file: yaboot.conf generated by the Ubuntu installer run: "man yaboot.conf" for details. Do not make changes until you have!! see also: /usr/share/doc/yaboot/examples for example configurations. For a dual-boot menu, add one or more of: bsd=/dev/hdaX, macos=/dev/hdaY, macosx=/dev/hdaZ boot="/dev/disk/by-id/scsi-SATA_ST3160023AS_5MT1GCWA-part2" device=/ht@0,f2000000/pci@3/k2-sata-root@c/@0/@0 partition=4 root="UUID=798a048f-ee48-49e0-bba3-111aed8dee04" timeout=12000 install=/usr/lib/yaboot/yaboot magicboot=/usr/lib/yaboot/ofboot enablecdboot macosx="/dev/disk/by-id/scsi-SATA_ST3160023AS_5MT1GCWA-part3" image=/boot/vmlinux label=Linux read-only initrd=/boot/initrd.img append="quiet splash" What do I add here so that yaboot will boot from my cd in like 3 minutes after startup? Thanks!

  Read the article

• Is text-only mode a saving or a problem for battery savings?

  - by Robottinosino

  A friend is flying to the US from Europe and asked me a very thought-provoking question, which I am not remotely able to answer with substance so I am asking it here: How to absolutely maximise battery life on an Ubuntu (laptop) install? do not rush to mark this as duplicate, there is an important point here: does -GNOME- help or worsen battery life? Let me provide some context: The only task he needs to perform is: edit text files in Vim. He is unsure whether running GNOME will drain his battery life more or actually save him some battery life given the smarts of GNOME's power management features like "switch this peripheral to -power save- after X minutes..." (GNOME might just be a configuration front-end for settings that are governed by command-line utils for all I know?) He could perfectly well boot the system in text-only mode and use the automatic 6 virtual consoles for his needs, if that's a saving at all over running tmux (I think so because of all the smart buffering/history/etc the latter does by default?) Exactly how would you advise him to run his laptop during his flight? What I told him already: power off WiFi in the BIOS, not from the "GUI" power off Bluetooth switch off the courtesy light and use low monitor brightness play music off of his phone, not mp3blaster do not use his tiny portable mouse (and do not attach any other USB gimmicks like "screen light", etc) stop development services he will not be using, especially apache2, tomcat, dovecot, postgresql, etc. Potentially: - switch off his cron jobs? (he does an rsync + tar + 7za of his "work in progress" every so often) I think the above is standard stuff one could get off StackExchange, and with many duplicates... the core of this question is, I think: __ will running Ubuntu in text-only mode be a saving in terms of battery life or a problem? why? (provide some technical arguments) __ I think it will be a saving but I am also scared about "other things" detecting and enabling advanced chipset power management features only when some services are started.. and fear these "services" may be off in text-only mode?

  Read the article

• x.265 in ffmpeg

  - by Levan

  Today I found out that x265 is already present in ffmpeg so I compiled ffmpeg with this guide Sadly libx265 did not work on ubuntu, however on windows I tried the same thing with zeranoe ffmpeg build and it worked without a problem. So do you think i did something wrong or it is not yet implemented in linux build (using that guide)? The results of the command ffmpeg -codecs | grep -i hevc show: ffmpeg version 2.1.git Copyright (c) 2000-2014 the FFmpeg developers built on Feb 19 2014 19:00:17 with gcc 4.8 (Ubuntu/Linaro 4.8.1-10ubuntu9) configuration: --prefix=/home/levan/ffmpeg_build --extra-cflags=-I/home/levan/ffmpeg_build/include --extra-ldflags=-L/home/levan/ffmpeg_build/lib --bindir=/home/levan/bin --extra-libs=-ldl --enable-gpl --enable-libass --enable-libfdk-aac --enable-libmp3lame --enable-libopus --enable-libtheora --enable-libvorbis --enable-libvpx --enable-libx264 --enable-nonfree --enable-x11grab libavutil 52. 64.100 / 52. 64.100 libavcodec 55. 52.102 / 55. 52.102 libavformat 55. 33.100 / 55. 33.100 libavdevice 55. 10.100 / 55. 10.100 libavfilter 4. 1.102 / 4. 1.102 libswscale 2. 5.101 / 2. 5.101 libswresample 0. 17.104 / 0. 17.104 libpostproc 52. 3.100 / 52. 3.100 D.V.L. hevc H.265 / HEVC (High Efficiency Video Coding) Thank you for your time

  Read the article

• Grub2 mutual dependency issue

  - by A T

  For various reasons I am installing .deb dependencies for grub2 using dpkg directly (rather than apt-get). root@ubuntu:/dl# dpkg -i grub-gfxpayload-lists_0.6_amd64.deb Selecting previously unselected package grub-gfxpayload-lists. (Reading database ... 249808 files and directories currently installed.) Preparing to unpack grub-gfxpayload-lists_0.6_amd64.deb ... Unpacking grub-gfxpayload-lists (0.6) ... dpkg: dependency problems prevent configuration of grub-gfxpayload-lists: grub-gfxpayload-lists depends on grub-pc (>= 1.99~20101210-1ubuntu2); however: Package grub-pc is not configured yet. dpkg: error processing package grub-gfxpayload-lists (--install): dependency problems - leaving unconfigured Processing triggers for man-db (2.6.7.1-1) ... Errors were encountered while processing: grub-gfxpayload-lists By configure I assume it means install+configure, so I tried: root@ubuntu:/dl# dpkg -i grub-pc_2.02~beta2-9_amd64.deb (Reading database ... 249818 files and directories currently installed.) Preparing to unpack grub-pc_2.02~beta2-9_amd64.deb ... Unpacking grub-pc (2.02~beta2-9) over (2.02~beta2-9) ... dpkg: dependency problems prevent configuration of grub-pc: grub-pc depends on grub2-common (= 2.02~beta2-9); however: Package grub2-common is not installed. grub-pc depends on grub-pc-bin (= 2.02~beta2-9); however: Package grub-pc-bin is not installed. grub-pc depends on grub-gfxpayload-lists; however: Package grub-gfxpayload-lists is not configured yet. dpkg: error processing package grub-pc (--install): dependency problems - leaving unconfigured Processing triggers for man-db (2.6.7.1-1) ... Errors were encountered while processing: grub-pc How do I solve this problem?

  Read the article

< Previous Page | 579 580 581 582 583 584 585 586 587 588 589 590  | Next Page >