Search Results

Search found 19966 results on 799 pages for 'wild thing'.

Page 585/799 | < Previous Page | 581 582 583 584 585 586 587 588 589 590 591 592  | Next Page >

• Two cisco gigabit switches refuse to link to each other. Any idea why?

  - by Prody

  I have 3 Linksys SR2024 switches which are basically non-managed 24 port Gbit + 2 miniGBIC. I now had to add another switch to the network, and my provider didn't have the SR2024 switch anymore, so I got the Cisco SLM2024 which was a bit more expensive. It's pretty much the same thing but with management (that I don't need). So I've connected the SLM2024 to a SR2024 via Cat6 cable, and for some strange reason, I get no link. If I connect any machine with a Gbit NIC to both switches, it links with 1Gbit autonegotiated. If I connect the SLM2024 to a non-Gbit switch (I have a cheap 4port ASUS switch), it will link just fine on 100Mbit full duplex. Since the SLM2024 has management, I've tried to see if something is misconfigured on it's side, but it's not, it advertises 1Gbit and lower. (hence the machines connecting succesfully at 1Gbit). Since the SR2024 that I'm trying to connect it to also connects successfully with another SR2024 and other Gbit machines, it means that it advertises Gbit too. But for some reason when I link the SR2024 to the SLM2024 I get no link. Please note that I've properly tested the wire. Does anyone have any idea what's wrong?

  Read the article

• Messages don’t always appear in Mail.app

  - by MikeHoss

  I asked this question on serverfault, but it was correctly suggested that superuser is better -- and I agree: My wife and I share a Mac and use different accounts. We both use Apple's standard Mail.app. We can also get to our email accounts via SquirrelMail that our webhost provides. Both SquirrelMail and Mail.app are connecting via IMAP. My wife was the first to notice that not all messages were getting to the Mail.app. She would check the Mac (our main machine) and then a little while later check mail from another machine via SquirrelMail and see messages there that should have been on the Mac. She would go back and those messages would never show up. Lately, I have been seeing the same thing, though less often. I can't reproduce it, or just look at a message to see if they haven't been moved over. I've looked in Junk, etc. and the Mac simply never sees those messages via IMAP. Does anyone have a guess to something I could poke around at?

  Read the article

• CentOS and OpenSSH [on hold]

  - by Stephen

  I've recently installed CentOS 6 on an old Dell PC. I'm trying to setup OpenSSH at the moment, I been following some tutorials (http://www.youtube.com/watch?v=QKafb0koJEg) on You Tube, while they have been very helpful I'm at the point where I need to ask some questions. My goal here is to be able to access the server from my work computer and from my personal laptop (which will be on the same home network as the server). I've installed OpenSSH with no issues. So the first thing I was advised to do was port forwarding. So in the sshd_config file, I've changed Port 22 to Port xxxx (where xxxx is a obviously a four digit value). I then restart the sshd service. I've also configured my router for forward port 22 onto xxxx. Is there anything else I need to do? I've generated the keys on my laptop, and I'm trying to copy them to the server as follows: scp id_rsa.pub xxxxxxxx@localhost:.ssh/authorized_keys but this command fails with the following error message: ssh: connect to host localhost port 22: Connection refused lost connection Any help appreciated. Regards...

  Read the article

• Display on secondary video card (Nvidia 8400 GS): horrible refresh, bogs system

  - by minameismud

  This is my work computer, but it's a small shop. We do business software development. The most hardcore thing we create is some web animations with html5 and fancy javascript/css. The base machine is a Dell Precision T3500 - Xeon W3550 (3.07GHz quad), 6GB ram, pair of 500GB harddrives, and Win 7 x64 Enterprise SP1. My primary video card is an ATI FirePro V4800 1GB in a PCIe slot of some speed driving a pair of 23s at 1920x1080 through DisplayPort-HDMI adapters. The secondary card is an NVidia GeForce 8400GS in a PCI slot driving a single 17" at 1280x1024 through DVI. On either of the 23" monitors, windows move smoothly, scroll quickly, and are generally very responsive. On the 17", it's slow, chunky, and when I'm trying to scroll a ton of content, Windows will occasionally suggest I drop to the Windows Basic theme. I've updated drivers for both cards, and I've gotten every Windows update relating to video. Specifically: ATI FirePro Provider: Advanced Micro Devices, Inc Date: 6/22/2014 Version: 13.352.1014.0 NVidia 8400 GS Provider: NVIDIA Date: 7/2/2014 Version: 9.18.13.4052 Unfortunately, new hardware isn't really an option. Is there anything I can do software-wise to speed up the NVidia-driven monitor?

  Read the article

• NginxHttpAuthBasicModule with Sinatra & Passenger

  - by scainey

  I'm serving static pages from a Sinatra application using Nginx. I've implemented Basic Authentication for one page on the site using NginxHttpAuthBasicModule, the authentication succeeds but Nginx doesn't resolve the link. Error log gives - 2010/03/22 12:15:19 [error] 7143#0: *2902 open() "/home/me/live/mysite_home/public /mypage" failed (2: No such file or directory), client: 82.71.18.122, server: mysite.com, request: "GET /mypage HTTP/1.1", host: "mysite.com" The actual file is found at: /home/me/live/mysite_home/live/mypage.erb The configuration file is: server { listen 80; server_name mysite.com; root /home/me/live/mysite_home/public; passenger_enabled on; location /mypage { auth_basic "Restricted"; auth_basic_user_file htpasswd; } } server { listen 443; server_name mysite.com; root /home/me/live/mysite_home/public; passenger_enabled on; ssl on; ssl_certificate /etc/nginx/conf/certs/server.crt; ssl_certificate_key /etc/nginx/conf/certs/server.key; keepalive_timeout 70; location /mypage { auth_basic "Restricted"; auth_basic_user_file htpasswd; } } Not sure if this is a Sinatra, Passenger or Nginx thing, or if I'm just missing something.

  Read the article

• strange Kernel Process Threads taking over my AIX box....

  - by Paul

  When I check the Running Stats of my box I get the following: CPU User% Kern% Wait% Idle% Physc 0 37.5 57.4 0.0 5.1 0.01 2 0.0 18.3 0.0 81.7 0.00 3 0.0 22.5 0.0 77.5 0.00 4 0.0 17.0 0.0 83.0 0.00 5 0.0 20.5 0.0 79.5 0.00 6 0.0 33.7 0.0 66.3 0.00 7 0.0 4.4 0.0 95.6 0.00 8 0.0 19.3 0.0 80.7 0.00 9 0.0 22.3 0.0 77.7 0.00 10 0.0 19.2 0.0 80.8 0.00 1 0.0 1.3 0.0 98.7 0.00 11 0.0 21.8 0.0 78.2 0.00 21 0.0 62.9 0.0 37.1 0.00 12 0.0 21.1 0.0 78.9 0.00 13 0.0 22.7 0.0 77.3 0.00 14 0.0 18.1 0.0 81.9 0.00 15 0.0 21.2 0.0 78.8 0.00 16 0.0 19.1 0.0 80.9 0.00 The Kern% seems high to me and I cannot find a reason for this much Kernel activity.... Doing a deep dive into what User processes are doing I find nothing with significant CPU utilization even though TOPAS and SAR both show the same thing.... One CPU with 30-60 % user and every processor with 5-30% Kernel % utilization... What is my box doing??? here is a second sample of CPU % from TOPAS CPU User% Kern% Wait% Idle% Physc 0 67.8 31.4 0.1 0.7 0.14 2 0.0 18.2 0.0 81.8 0.00 3 0.0 20.3 0.0 79.7 0.00 4 0.0 17.3 0.0 82.7 0.00 5 0.0 20.7 0.0 79.3 0.00 6 0.0 39.2 0.0 60.8 0.00 7 0.0 5.0 0.0 95.0 0.00 8 0.0 17.9 0.0 82.1 0.00 9 0.0 22.0 0.0 78.0 0.00 10 0.0 18.0 0.0 82.0 0.00 1 0.0 0.7 0.0 99.3 0.02 11 0.0 21.7 0.0 78.3 0.00 21 0.0 21.7 0.0 78.3 0.00 12 0.0 17.0 0.0 83.0 0.00 13 0.0 21.1 0.0 78.9 0.00 14 0.0 17.8 0.0 82.2 0.00 15 0.0 21.8 0.0 78.2 0.00 16 0.0 17.6 0.0 82.4 0.00 Any ideas to help identify what is running in the Kernel Space would be great....

  Read the article

• Notepad++ FTP best solution

  - by yoda

  Hi, I use Notepad++ for more than 2 years now, and there's only 1 thing that it needs for me to be perfect: a actually-working-ftp-plugin. It has an ftp plugin, written by someone that meanwhile left the project (by meanwhile I mean a long time ago), and since then nobody had courage to improve it. The problem is that it does't handle connections very well. Sometimes it lost connection with the server and literally "blocks", others don't save the files properly, other only load half of the ftp files, etc etc .. My question is: Is there a way to use ftp and notepad++ (without using its build-in ftp or a ftp client like filezilla)? I've tried using NetDrive, but it gets stuck sometimes (makes the editor crash), and everytime the temporary file is refreshed by windows / NetDrive, it will load the new file without asking and skip the pointer to the end of the file (very very very annoying). In case you know how to make the built-in notepad++ ftp plugin work at 100%, I'd be much more happy! I'd like to have some feedback from you guys :) (I'm using Windows Vista) Thanks in advance!

  Read the article

• What is wrong with my home network? (Routing and connection issues)

  - by David

  I have a corporate laptop that was provided to me by a client and I'm having some rather odd difficulties with it when I put the laptop on my home network. When I first brought the machine home it behaved like any other laptop. Once it was connected to the network it was assigned an IP address and I could remote into it just fine using the machine name. Lately though, whenever I put this laptop on my network I am not able to ping or RDP into the machine as the host name doesn't properly resolve. Additionally I'm able to see the device and it's assigned IP address clearly in my router firmware. This gets even more strange as now when I try to ping it's IP address listed in my router, I see that it's actually trying to ping my own machine (screenshot of this very odd event below). This has actually driven me crazy to the point that I have actually replaced my router (it was behaving oddly in other ways), and I'm continuing to have these problems. The above ping capture is from the new router. As far as network goes I am now currently using an NetGear R7000 Nighthawk and I haven't customized any of the networking settings in the router just yet (installed yesterday). I would appreciate any advice possible and would be happy to provide further diagnostic information. Networking isn't my strong suit, so I'm not even sure where to begin unraveling this thing.

  Read the article

• Why is my HP TouchSmart tx2 1025dx shutting down?

  - by Kristy

  I'm having an issue with my HP tx2 1025dx laptop. Sometimes it will spontaneously shut itself off. First, the screen will go out. Next, the computer itself will shut down. This usually occurs when I am doing something that requires a lot of resources, but lately can happen when I am doing something as simple as using an Office app. I think it may be heat related, if I try to boot the laptop after it shuts itself down, it will shut itself down again before startup is complete. If I let it cool down for a while and then come back to it, the computer will boot properly. These shutdowns are always accompanied by high temperatures on the bottom right side, as well as the right side of the keyboard. I am using a laptop cooler with two fans, and it is not making a bit of difference. This is the second TouchSmart we have owned, the first one had the same issues, we sent it in to HP after it finally refused to reboot. They “fixed” it, and it worked fine for about a month before doing the exact same thing. Unfortunately we had bought the second one before the issues began with the original, if I had known this would be a problem, I would not have purchased another TouchSmart. This particular laptop we have had for more than a year and it didn’t start these issues until a couple of months ago. Any suggestions as to how to fix this problem?

  Read the article

• How do I disable DirectDraw and Direct3D acceleration on Windows 8? [closed]

  - by Favourite Chigozie Onwuemene

  Some old games that i would really like to play run slowly on some graphic drivers when direct3d acceleration is enabled. I have tried many suggestions but none seems to work. The only thing i have not tried is disabling direct3d acceleration. Is it possible to disable DirectDraw and Direct3D acceleration on my Windows 8 pc? There are certain bad versions of GeForce drivers that cause this problem. This is a problem in the drivers themselves and is unfortunately completely outside our control. The recommended way to fix this problem is to update your graphics card drivers (go to NVIDIA's web site for this). Alternatively, there is a workaround that alleviates or solves the slowdown problem altogether. Try this: Right-click on your desktop and select "Properties". Go to the "Settings" tab and click on "Advanced...". Click on the "Troubleshooting" tab and move the slider to the left until it says that all DirectDraw and Direct3D accelerations have been disabled (around the middle of the range). Finally, click on "OK". Note that this workaround might cause other games on your computer to slow down, so you may have to switch back and forth between settings, but it's certainly worth a try if you can't obtain an updated graphics driver. -source: interactionstudios

  Read the article

• NginxHttpAuthBasicModule with Sinatra & Passenger

  - by scainey

  Hi, I'm serving static pages from a Sinatra application using Nginx. I've implemented Basic Authentication for one page on the site using NginxHttpAuthBasicModule, the authentication succeeds but Nginx doesn't resolve the link. Error log gives - 2010/03/22 12:15:19 [error] 7143#0: *2902 open() "/home/me/live/mysite_home/public /mypage" failed (2: No such file or directory), client: 82.71.18.122, server: mysite.com, request: "GET /mypage HTTP/1.1", host: "mysite.com" The actual file is found at: /home/me/live/mysite_home/live/mypage.erb The configuration file is: server { listen 80; server_name mysite.com; root /home/me/live/mysite_home/public; passenger_enabled on; location /mypage { auth_basic "Restricted"; auth_basic_user_file htpasswd; } } server { listen 443; server_name mysite.com; root /home/me/live/mysite_home/public; passenger_enabled on; ssl on; ssl_certificate /etc/nginx/conf/certs/server.crt; ssl_certificate_key /etc/nginx/conf/certs/server.key; keepalive_timeout 70; location /mypage { auth_basic "Restricted"; auth_basic_user_file htpasswd; } } Not sure if this is a Sinatra, Passenger or Nginx thing, or if I'm just missing something.

  Read the article

• TGT validation fails, but only for one user

  - by wzzrd

  I'm seeing the weirdest thing here. I have a couple of RHEL3, 4 and 5 machines that validate user credentials through Kerberos with an Active Directoy domain controller as their KDC. This works for all of my users, save one. There is one account that is unable to log into RHEL3 Linux machines and generates the following errors there: May 31 13:53:19 mybox sshd(pam_unix)[7186]: authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=10.0.0.1 user=user May 31 13:53:20 mybox sshd[7186]: pam_krb5: TGT verification failed for `user' May 31 13:53:20 mybox sshd[7186]: pam_krb5: authentication fails for `user' Other accounts, like my own, are fine: May 31 17:25:30 mybox sshd(pam_unix)[12913]: authentication failure; logname= uid=0 euid=0 tty=ssh ruser= rhost=10.0.0.1 user=myuser May 31 17:25:31 mybox sshd[12913]: pam_krb5: TGT for myuser successfully verified May 31 17:25:31 mybox sshd[12913]: pam_krb5: authentication succeeds for `myuser' May 31 17:25:31 mybox sshd(pam_unix)[12915]: session opened for user myuser by (uid=0) As you can see, TGT validation fails. This only happens for this specific account, not for any other. The failing useraccount's password has been reset, I inspected both user objects in Active Directory, but I see nothing out of the ordinary. If I have the failing useraccount log into a RHEL4 or 5 box, there is not problem, so it must be RHEL3 specific, but the fact that only one account suffers from this, alludes me. Maybe someone has seen this before?

  Read the article

• Web Server slows down (ASP.NET)

  - by mfeingold

  below is a question I posted on stackoverflow . as suggested by Martin Clarke I also post it here. We have a really strange problem. One of the servers in the server farm becomes really slow. We see a number of timeouts in the logs and overall response time is not where it should be (and is on other servers in the farm). What is also strange is that it is not just the web app - Just logging into the server takes up to 1.5 min to show you the desktop. Once you are in, the system is as responsive as ever - unless you try to launch something, i.e. notepad - it takes another minute to launch and after launch it works fine. I checked a number of things - memory utilization is reasonable, CPU is below 15%, windows handles, event logs do not show anything. Recycling the aps.net process does not fix it - it still takes over a minute to log in. Rebooting the server helped, but now it started to slow down again. After a closer look we found out that Windows Temp directory is full of temp files - over 65k files. This is certainly something to take care of. But my question is could it be the root cause of the sluggishness, or there is still something else lurking in the shadows? Edit After more digging I am zeroing in on the issue related to the size of temp directories. This article: (see the original post this thing will not let me include a second link) describes something very similar. It still does not answer the question why the server is still slow even there is no activity.

  Read the article

• Installing Debian 7.6.0 on Lenovo Y50

  - by Girauder

  I was trying to install Debian on my new laptop: a Lenovo Y50 64bit running Windows 8. I got together with a friend and installed Debian in his computer first and had no problems. However I've tried to install Debian several times using the AMD64 KDE and netinst versions and accomplished nothing. First try: installed the KDE version. Grub would let me choose which operating system I wanted, but when I selected Debian it would only load the command line. Second try: Reinstalled but this time with the netinst version. I only got a black screen where I could type but nothing else. Third Try. Tried the netinst again. This time after making the partitions I got a message that said that no EFI partition was found. I ignored the message and this time it wouldn't even load Grub. only a command like interface with grub rescue or something. Not once did I get an error during the installation. What am I doing wrong? I assume the problem is I need to make an EFI partition or something like that. So why is it that during the first installations I didn't ask me for that. And if that is indeed the problem, How can I solve it? Update So the installation failed again... as predicted. Here you can find the Disk Management picture. http://postimg.org/image/433cpfkjz/ Please somebody help me. I keep getting the grub rescue thing. secure boot is disabled and legacy support is set first.

  Read the article

• Computer Turns on Briefly then right back off again.

  - by goddamnyouryan

  So yesterday I came home from work and went to turn my computer on....it turned on for about 5 seconds then promptly turned right back off again...before I ever saw anything on the screen. I tried again, same result. After several attempts, I've found that the length at which it turns on differs. After trying multiple times in a row, it only stays on for about 3 seconds. If I let it rest for a bit it sometimes will stay on for up to a minute (though it never boots, the screen stays black the whole time). I'm not sure what is causing this issue...I built this computer a little more than 2 years ago and this is the first issue I have ever had with it. I did all the usual checks: -It's not the power switch -The capacitors on the motherboard all seem to be in working order -The PSU seems to be fine as it lights up, fan spins, and will sometimes stay on for about a minute period My hope is that the thermal paste on the cpu has degraded and just needs to be re-applied. Does that seem like a reasonable assumption? I'm going to tear the thing apart and do a minimum system build when I get home, but any heads up as to what I should be looking for would be much appreciated. Any thoughts?

  Read the article

• PPTP VPN on Server 2008 Enterprise

  - by Mike K

  I asked this question on Server fault and was told that was not allowed so im moving it here. I am running Windows Server 2008 enterprise in my HOME network inside of vmware workstation. I am running this on my home network to setup a PPTP VPN connection at home. I have correctly setup everything I needed to make it work, including opening all the ports, 1723 and 43 (GRE). I am able to connect just fine, but when I connect I dont have internet unless I uncheck use remote gateway. The thing is, I want to use the remote gateway to route all my traffic through that connection. Can someone tell me why this isnt working and how to get it to work. When I have remote gateway checked, and I do an ipconfig I dont get a remote gateway for the VPN connection, its 0.0.0.0 when id assume if connected properly should be 192.168.1.254 (my ATT Home Router). Also, if I cant get the remote gateway issue to work, and I have to uncheck that box to get internet, does this mean my VPN session is no longer encrypted? I am fully aware the PPTP VPN is the weakest VPN encryption out there but still having that extra layer of security when im on an unsecure wifi connection makes me feel a bit better. Thank you for all your help in advance. Someone told me I need to setup a gateway or router configured on the server. If thats the case, how go I go about telling the remote co

  Read the article

• Mac OS X: Applications not responding

  - by Robot55

  This happens to me several times a day. I'll quit an app, the window will close, but the app won't finish shutting down. It stays open in the dock, and right clicking and force quit show not responding. Force quit won't work. I can't shut the app down. Starting any other app when this happens causes that app to behave in exactly the same way: the icon opens in the dock, but the app is non-responsive and can't be forced to quit. Can't access terminal when this happens, because it locks up just like all the apps. While I haven't tried to open every app, I think any app I try to open when this is happening will lock up. If I relaunch Finder, it too locks up and then the only thing left is to hold down the power button for a hard reboot. Any app that is running while this is happening will continue to run normally unless I try to shut it down. Repairing disk permissions has no effect. I also did a time machine and a full restore on a brand new MbP - and sure enough, after restore, the new MbP suffers form the same problem. Creating a new user has no effect. Any thoughts? Please help MacBook Pro 15" AG 2.53ghz i5 cpu 8gb RAM 500gb HD (over 200gb free)

  Read the article

• Corrupted Laptop - Transfer Data Without My Computer (explorer.exe) Using Command Line

  - by nicorellius

  I have a laptop (Toshiba Satellite) that is pretty messed up. The person this belongs too already replaced it with a new machine. My job is to transfer all her data from this machine to disk so that I can transfer it to her. She doesn't want to lose any data (understandably so). Any operation I attempted (i.e., double clicking on any folder icon, like My Documents, My Computer, etc) resulted din a complete crash. The only good news is that I can actually start and navigate around using the command line. Also, I can access the internet. I have a network, so if I can map the drives I can get this thing figured out (hopefully). Also, I tried a USB drive but I couldn't figure out how to access it from the command line. Two questions (I need to use the command line for these): How would I go about accessing the USB drive and how can I map the shared drives on my network so that I may cd to that directory for use of the copy command?

  Read the article

• Different font SIZES in a Text Editor, based on Script(Alphabet) type (ie. per Unicode Code-Block)

  - by fred.bear

  Some non-Latin-based scripts(alphabets) have more detail in their glyphs than do the Latin-based-script equivalents, and typically need a larger font to give the same degree of legibility (resolution-wise). Sometimes, both script types need to be present in the same file. Notepad++ allows different font SIZES (and colour, etc) courtesy of syntax-highlighting. This allows me to display larger-fonted non-Latin-based script in a // BIG-FONT comment. Although this has been quite handy for me in some situations, it is quite limited. A Word Processor can handle this scenario, but I'm not interested in that. I want a nice simple(?) plain(?) Text Editor to do it... on a per script-type basis... eg. mixing Latin-1 and Devanagari (and Mandarin, and ... Such a thing may not exits, but Notepad++ has shown that a simple(?) plain(?) Text Editor is capable of it. Does anyone know of such a Text Editor? ...Q. Why not a Word Processor? ...A. Because GCC and Python don't like that format! but UTF-8 is fine.

  Read the article

• Open source app to manage and run commands on cloud servers? [closed]

  - by Mark Theunissen

  I'm creating a SaaS platform, and I need a component / library that can create, delete and store the connection details for cloud servers. It also needs to support executing shell commands on these servers and returning the response to the caller. I want a central database of servers and their configuration, plus the ability to reach out and manage the servers via SSH execution of bash scripts. I don't want something that needs agents on every server like Chef. For example, this command is received by the hypothetical application: CREATE USER server = server12345 name = myuser It's translated into the following set of actions and executed by the app, which knows how to connect to server12345, and how to create a user on that server: $ ssh root@server12345 $ adduser myuser And returns the output from the shell: Added user myuser. I've done research on Google and can't quite quite find something that does this already. I've found: fabric This part handles the executing of the shell commands very elegantly, and can take multiple server definitions, but it's supposed to be a deployment tool so doesn't do everything that would be required above - for example, it doesn't have a daemon mode where it listens for commands - it expects to be executed on the shell. It also can't provide the central database functionality. libcloud This library can handle the server admin (CRUD) part, but doesn't have a command interface daemon either, and doesn't let you execute commands on the servers. I guess I need something that is a combination of libcloud, fabric and django for an API. Or something else that does that same thing regardless of language. Overmind Overmind is a GUI and wrapper around libcloud, but doesn't support the command execution part. What am I missing here?

  Read the article

• Can't login to Windows server 2008 (as any user, not even locally, not in safe mode but I have right credentials)

  - by Saix

  Just from nowhere I can't login to my Windows server 2008 machine. All the services like FTP server or webserver (which I'm actually not using, just remote desktop and FTP) are running. Whatever credentials I try (even/especialy administrator), it always says Unknown Username or bad password. I have already tried hard turn off/on and safe mode without luck. Also I already tried type in login name as SERVER NAME\user or Workgroup\user (every case sensitive scenario), still says I have wrong login. Usually we are using remote desktop to access the machine but local access over KVM doesn't work either. Now I'm lock out of any control or any way to do something. There's just logon screen preceding by ctrl+alt+del to login alert. Without me able to login I can't actually try to fix anything. Can't find much more on Internet except the SERVER NAME\user thing. Reinstall would be the last resort but I can't let things this way for much longer anyway. This server is vital. If it would be any help, I think automatic Windows updates are turned off and there were no updates or newly installed software for last couple years and just few soft restarts, non of them recently. It happened during it's runtime while all other services were still up and running, so this couldn't be just some Windows nasty screw up during boot or something. What could have possibly changed? What are my options now?

  Read the article

• Running Ubuntu on Toshiba L630

  - by Toshibalin

  After suffering with the following error while trying to install Ubuntu onto my Toshiba L630 (kernel_thread_helper+0x0 0x10). I bypassed the error and managed to install the OS by going going into the "installation setup menu"( by pressing f6 while booting from my Ubuntu Installation CD) and assigning "acpi = off". I believe this fixes the problem because it stops the laptop doing checks that aren't compatible with the software. However, now that I have Ubuntu installed, I cannot run the bloody thing because I have no way of choosing "acpi=off" before booting Ubuntu. I guess this is a pretty broad question but I'm going to ask it anyways. Has anyone managed to find a version of linux that works on an L630 without any errors? If not, Is there a way to choose acpi=off before booting? Maybe by adding a line to the grub? Also, does anybody think I'm wasting my time? I read somewhere that toshiba laptops don't work well with linux. So if there isn't a fix for this I would appreciate being alerted about this. Cheers

  Read the article

• [deb-5.0] Setup DNS on my server so I can put my IPs in as nameservers of my domain provider

  - by Maurycy Zarzycki

  Basically, my unmanaged VPS provider doesn't supply me with nameserver which I can use with my domain provider to route domain to my server. As I've been told: You need to configure the custom DNS server in your VPS, to setup the custom nameservers. Please refer the following article that would help: http://www.linuxhomenetworking.com/wiki/index.php/Quick_HOWTO_:_Ch18_:_Configuring_DNS Once you configure the nameserver records, please update the domain registrar panel with the custom nameserver details. I tried to follow this guide but it seems to be a bit outdated, and I am complete newb with non-windows systems. I also scanned the google for other articles which could help me with this problem but, alas, nothing I found was of any value for someone who doesn't know this stuff better than his own pockets. I realize this is quite a complex thing to do, but maybe there is some way to automate it? Or a better solution, like a paid service which would act as my nameservers (this one would be interesting), or even hoped to find some company which "rents" people to do stuff like that. Blah, any help will be appreciated, I am at a complete loss here. I can follow some of these steps, but then I soon find that half of the files which are mentioned in the article are somehow not existing anywhere on the server which confuses me, and once we get to the point of creating Zone I can't really decipher all the things written there :/. As per title, my system is Debian 5.0.

  Read the article

• [deb-5.0] Setup DNS on my server so I can put my IPs in as nameservers of my domain provider

  - by Maurycy Zarzycki

  Basically, my unmanaged VPS provider doesn't supply me with nameserver which I can use with my domain provider to route domain to my server. As I've been told: You need to configure the custom DNS server in your VPS, to setup the custom nameservers. Please refer the following article that would help: http://www.linuxhomenetworking.com/wiki/index.php/Quick_HOWTO_:_Ch18_:_Configuring_DNS Once you configure the nameserver records, please update the domain registrar panel with the custom nameserver details. I tried to follow this guide but it seems to be a bit outdated, and I am complete newb with non-windows systems. I also scanned the google for other articles which could help me with this problem but, alas, nothing I found was of any value for someone who doesn't know this stuff better than his own pockets. I realize this is quite a complex thing to do, but maybe there is some way to automate it? Or a better solution, like a paid service which would act as my nameservers (this one would be interesting), or even hoped to find some company which "rents" people to do stuff like that. Blah, any help will be appreciated, I am at a complete loss here. I can follow some of these steps, but then I soon find that half of the files which are mentioned in the article are somehow not existing anywhere on the server which confuses me, and once we get to the point of creating Zone I can't really decipher all the things written there :/. As per title, my system is Debian 5.0.

  Read the article

• Iptables state tracking

  - by complexgeek

  Hi there. I've just taken over administration of a fairly complex firewall ruleset for a firewall box running Fedora Core 12, and there's one thing about it that is puzzling me. When I run nmap on the gateway from outside the network, I see all the expected services, but also sunrpc on port 111. The INPUT chain has DEFAULT DROP set, and there is no rule allowing port 111. As best I can tell (watching the packet counters before/during/after the scan) it's being allowed by the rule: "-m state --state RELATED,ESTABLISHED -j ACCEPT" but I don't understand why a brand new TCP connection would be considered RELATED or ESTABLISHED. Any suggestions would be greatly appreciated. EDIT: Conntrack modules: nf_conntrack_netlink 14925 0 nfnetlink 3479 1 nf_conntrack_netlink nf_conntrack_irc 5206 1 nf_nat_irc nf_conntrack_proto_udplite 3138 0 nf_conntrack_h323 62110 1 nf_nat_h323 nf_conntrack_proto_dccp 6878 0 nf_conntrack_sip 16921 1 nf_nat_sip nf_conntrack_proto_sctp 11131 0 nf_conntrack_pptp 10673 1 nf_nat_pptp nf_conntrack_sane 5458 0 nf_conntrack_proto_gre 6574 1 nf_conntrack_pptp nf_conntrack_amanda 2796 1 nf_nat_amanda nf_conntrack_ftp 11741 1 nf_nat_ftp nf_conntrack_tftp 4665 1 nf_nat_tftp nf_conntrack_netbios_ns 1534 0 nf_conntrack_ipv6 18504 2 ipv6 279399 40 ip6t_REJECT,nf_conntrack_ipv6 INPUT chain on the filter table: -A INPUT -s 192.168.200.10/32 -p tcp -m tcp --dport 22 -m state --state NEW,ESTABLISHED -j ACCEPT -A INPUT -s 127.0.0.0/8 -i lo -j ACCEPT -A INPUT -p udp -m udp --sport 67:68 --dport 67:68 -j ACCEPT -A INPUT -d 192.168.200.5/32 -i eth0 -j ACCEPT -A INPUT -d 192.168.1.2/32 -i eth0 -j ACCEPT -A INPUT -d {public_ip}/32 -i ppp0 -p tcp -m multiport --dports 22,80,443 -j ACCEPT -A INPUT -d {public_ip}/32 -i ppp0 -p tcp -m multiport --sports 22,25,80,443 -j ACCEPT -A INPUT -d {public_ip}/32 -i ppp0 -p udp -m udp --dport 1194 -j ACCEPT -A INPUT -d {public_ip}/32 -i ppp0 -p udp -m udp --sport 1194 -j ACCEPT -A INPUT -d {public_ip}/32 -i ppp0 -p udp -m multiport --sports 53,123 -j ACCEPT -A INPUT -d {public_ip}/32 -i ppp0 -p icmp -m icmp --icmp-type 8 -j ACCEPT -A INPUT -i eth0 -m state --state NEW -j ACCEPT -A INPUT -d {public_ip}/32 -m state --state NEW -j ACCEPT -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT eth0 is connected to the internal network, eth3 is connected to an ADSL modem in bridge mode, ppp0 is the WAN connection tunneled over eth3.

  Read the article

< Previous Page | 581 582 583 584 585 586 587 588 589 590 591 592  | Next Page >