Search Results

Search found 89603 results on 3585 pages for 'jordon user'.

Page 588/3585 | < Previous Page | 584 585 586 587 588 589 590 591 592 593 594 595  | Next Page >

• 3GB RAM Installed and Detected by BIOS, Windows Vista 32bit Only Sees 2GB

  - by Nathan Taylor

  I am attempting to install more RAM on a Windows Vista 32bit machine which is using a X6DAL-XG motherboard and the RAM amount reported in the BIOS is 3GB+, but Windows is only reporting 2GB installed. The motherboard has 6 RAM bays which I have populated with various combinations of 4 1GB sticks, and 2 512mb sticks, but no matter how I configure them Windows doesn't see more than 2GB. I realize of course 32-bit Windows has a 3gb cap on memory, but that doesn't explain why it will only report 2GB when there are in fact (currently) 5GB installed. I should think I would be able to see at least 3GB. According to the spec list for the motherboard the minimum RAM requirements are DDR333/266mhz installed in pairs. I have done this exactly, and the BIOS isn't reporting any problems at POST. RAM Configuration (according to CPU-Z): Slot #1: Kingston 128mx72D266C25 - 1024mb PC2100 (133mhz) Slot #2: Kingston KVR266X72RC25/1024 - 1024mb PC2100 (133mhz) Slot #3: PQI - 512mb PC2700 (166mhz) Slot #4: Kingston 128mx72D266C25 - 1024mb PC2100 (133mhz) Slot #5: Kingston KVR266X72RC25/1024 - 1024mb PC2100 (133mhz) Slot #6: PQI - 512mb PC2700 (166mhz) I'm not sure if memory specs above conflict with this statement in the motherboard manual or not: Memory Support The X6DAL-XG supports up to 12GB/24GB of registered ECC DDR333/266 (PC2700/PC2100) memory. The motherboard was designed to support 4GB (PC2100) modules in each slot, but only the 2GB modules have been tested. When using registered ECC DDR333 (PC2700) memory, installing four pieces of double-banked memory or six pieces of single-banked memory is supported. So, am I doing something wrong with the RAM I have now, or is there some sort of compatibility problem which I am missing? Thanks!

  Read the article

• Gnu screen with local scrollback buffer?

  - by Hugh Perkins

  I'm using a remote server over a very slow and unreliable network connection. So, I want to use gnu screen in order not to lose what I'm doing whenever I get disconnected. But I want a local scrollback buffer, on my local computer, so that scrollback doesn't have to go across the network, which is incredibly slow. Is there either something like gnu screen, but with a local scrollback buffer; or else a way of using gnu screen with a local scrollback buffer?

  Read the article

• Broke NetBeans file associations in Windows XP how do I get them back?

  - by Serhiy

  I broke my file association in XP... Does anyone have any clue how to fix it? When I right click and select Open With... the application I want to use (NetBeans) to open the file is not on the list... and when I browse for it it won't let me select it (well it does but then won't add it to the list). The way I broke it is by installing 6.7 and then uninstalling 6.5.... since then my file associations have all been broken. I even tried uninstalling NetBeans and reinstalling it again... no luck... I even went as far as adding my own action called "OpenIt" to the file types I wanted... and that works... but only if the file/folders that contain in don't have any spaces... otherwise NetBeans throws a ".....does not exist, or is not a plain file". Thus nothing off the desktop can be opened... Does anyone know of how I can fix this problem? Thanks.

  Read the article

• Excel - export sheet to fixed-width text file?

  - by jkohlhepp

  I know that Excel has functionality to import fixed-width text files where it presents a dialog that lets you choose where the begins and ends of fields are which it puts into columns. Does it also have functionality where, given an existing spreadsheet, you can export to a fixed-width text file? If so, how do I access this? I have tried using Save As and choosing Text File but it seems to only save as Tab-delimited which doesn't help me. This is Excel 2003 if it matters. Thanks, ~ Justin

  Read the article

• Problem in installing OpenOffice 3.1 on Solaris 10

  - by Sunil Kumar Sahoo

  I want OpenOffice in Solaris. So I downloaded OpenOffice from the link below. http://download.openoffice.org/other.html#tested-full My OpenOffice is in .tar.gz format so I unzipped the file using gunzip and then untar'ed the file using tar xvf command. Now I got a directory containing packages subfolder. When I cd to that directory I found too many subdirectories. I could not find a single .pkg file or .jar file or .sh file so that I can install the OpenOffice in Solaris 10. How can I install OpenOffice in Solaris 10 given the scenario above?

  Read the article

• 2-Bay External HDD Enclosure in JBOD mode fails to detect both drives (Linux & Windows)

  - by mgc8888

  I recently purchased a couple of USB 3.0 External HDD Enclosures to use for storage and backup; the idea was to have one act as backup to the other, with 4 x 3TB drives in total. However, the second drive in each is not accessible in either Linux nor Windows, and I could not determine the reason. 1. Situation The two enclosures are slightly different (couldn't find them in stock at the same time) yet from many little details appear to be the same Chinese base design with a tweaked outer shell. The models are: Sharkoon 2-Bay RAID Box Fantec MR-35DU3 The drives are Seagate 3TB Barracuda ST33000651AS, firmware CC44, all identical. From reading manuals and online sources, I determined that JBOD would be the optimal setup for my needs -- addressing the two drives separately in each enclosure would be important, making it easy to swap drives and mix&match them if needed; all the other modes implied the controller doing a combination of the drives. The software used was Debian GNU/Linux - testing/wheezy - kernel 2.6.39-2 and Windows 7 Ultimate. 2. Description of the problem Now, here comes the problem: every time I connect either of the enclosures to a PC using the supplied cable (tried a different one as well), only the HDD in the top bay is readable, the one below is detected yet errors out in various ways. According to the manuals, it should not happen: in JBOD, the system should be able to "see" two separate drives upon connection. This happens with both enclosures and any combination of HDDs (i.e. if I swap them, the same thing happens), so the HDDs are good and I think so are the enclosures (two different companies making similar products that failed in an identical fashion would be very unlikely). The top HDD can be used fine every time, I actually tried a speed test from Linux and got about 150MiB/s reads, so all is working as it should; the one below refuses to work every time. So the failure is consistent. To make sure this was not some obscure Linux bug, I tried the same under Windows 7, and the system also only created one drive letter for a drive of 3TB size (so it was only seeing one instead of both). Placing an older, known good, 2TB drive in the top bay made that the one recognised, so we have the same issue under Windows as well. Log entries under Linux (tested here with a 3TB and a 2TB drive so I could differentiate them; either one works in the top enclosure, in the test setup the 3TB one is on top). You can see them being detected, the top one is ok, but for the bottom one only errors: Jul 19 23:28:15 media kernel: [260150.582436] usb 6-1: New USB device found, idVendor=1ca1, idProduct=18ae Jul 19 23:28:15 media kernel: [260150.582440] usb 6-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3 Jul 19 23:28:15 media kernel: [260150.582442] usb 6-1: Product: Usb Sata Bridge Jul 19 23:28:15 media kernel: [260150.582444] usb 6-1: Manufacturer: SYMWAVE Jul 19 23:28:15 media kernel: [260150.582446] usb 6-1: SerialNumber: 39584B304C4E3441 Jul 19 23:28:15 media kernel: [260150.870412] scsi11 : usb-storage 6-1:1.0 Jul 19 23:28:16 media kernel: [260151.882087] scsi 11:0:0:0: Direct-Access SYMWAVE ST33000651AS CC44 PQ: 0 ANSI: 4 Jul 19 23:28:16 media kernel: [260151.882242] scsi 11:0:0:1: Direct-Access SYMWAVE ST32000641AS CC12 PQ: 0 ANSI: 4 Jul 19 23:28:16 media kernel: [260151.882677] sd 11:0:0:0: Attached scsi generic sg2 type 0 Jul 19 23:28:16 media kernel: [260151.882774] sd 11:0:0:0: [sdb] Very big device. Trying to use READ CAPACITY(16). Jul 19 23:28:16 media kernel: [260151.882857] sd 11:0:0:1: Attached scsi generic sg3 type 0 Jul 19 23:28:16 media kernel: [260151.882893] sd 11:0:0:0: [sdb] 5860533168 512-byte logical blocks: (3.00 TB/2.72 TiB) Jul 19 23:28:16 media kernel: [260151.883085] xhci_hcd 0000:03:00.0: WARN: Stalled endpoint Jul 19 23:28:16 media kernel: [260151.883582] sd 11:0:0:0: [sdb] Write Protect is off Jul 19 23:28:16 media kernel: [260151.883961] sd 11:0:0:1: [sdc] 3907029168 512-byte logical blocks: (2.00 TB/1.81 TiB) Jul 19 23:28:16 media kernel: [260151.884145] xhci_hcd 0000:03:00.0: WARN: Stalled endpoint Jul 19 23:28:16 media kernel: [260151.884570] sd 11:0:0:1: [sdc] Write Protect is off Jul 19 23:28:16 media kernel: [260151.884855] sd 11:0:0:0: [sdb] Very big device. Trying to use READ CAPACITY(16). Jul 19 23:28:16 media kernel: [260151.885286] xhci_hcd 0000:03:00.0: WARN: Stalled endpoint Jul 19 23:28:16 media kernel: [260151.885807] xhci_hcd 0000:03:00.0: WARN: Stalled endpoint Jul 19 23:28:16 media kernel: [260151.909595] xhci_hcd 0000:03:00.0: WARN: Stalled endpoint Jul 19 23:28:16 media kernel: [260151.910159] sd 11:0:0:1: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE Jul 19 23:28:16 media kernel: [260151.910163] sd 11:0:0:1: [sdc] Sense Key : Illegal Request [current] Jul 19 23:28:16 media kernel: [260151.910167] Info fld=0x0 Jul 19 23:28:16 media kernel: [260151.910169] sd 11:0:0:1: [sdc] Add. Sense: Invalid field in cdb Jul 19 23:28:16 media kernel: [260151.910172] sd 11:0:0:1: [sdc] CDB: Read(10): 28 20 00 00 00 00 00 00 08 00 Jul 19 23:28:16 media kernel: [260151.910182] quiet_error: 2 callbacks suppressed Jul 19 23:28:16 media kernel: [260151.910570] xhci_hcd 0000:03:00.0: WARN: Stalled endpoint Jul 19 23:28:16 media kernel: [260151.911153] sd 11:0:0:1: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE Jul 19 23:28:16 media kernel: [260151.911156] sd 11:0:0:1: [sdc] Sense Key : Illegal Request [current] Jul 19 23:28:16 media kernel: [260151.911159] Info fld=0x0 Jul 19 23:28:16 media kernel: [260151.911161] sd 11:0:0:1: [sdc] Add. Sense: Invalid field in cdb Jul 19 23:28:16 media kernel: [260151.911164] sd 11:0:0:1: [sdc] CDB: Read(10): 28 20 00 00 00 00 00 00 08 00 Jul 19 23:28:16 media kernel: [260151.911385] xhci_hcd 0000:03:00.0: WARN: Stalled endpoint Jul 19 23:28:16 media kernel: [260151.911902] sd 11:0:0:1: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE Jul 19 23:28:16 media kernel: [260151.911905] sd 11:0:0:1: [sdc] Sense Key : Illegal Request [current] Jul 19 23:28:16 media kernel: [260151.911908] Info fld=0x0 Jul 19 23:28:16 media kernel: [260151.911910] sd 11:0:0:1: [sdc] Add. Sense: Invalid field in cdb Jul 19 23:28:16 media kernel: [260151.911913] sd 11:0:0:1: [sdc] CDB: Read(10): 28 20 00 00 00 00 00 00 08 00 Jul 19 23:28:16 media kernel: [260151.912128] xhci_hcd 0000:03:00.0: WARN: Stalled endpoint Jul 19 23:28:16 media kernel: [260151.912650] sd 11:0:0:1: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE Jul 19 23:28:16 media kernel: [260151.912653] sd 11:0:0:1: [sdc] Sense Key : Illegal Request [current] Jul 19 23:28:16 media kernel: [260151.912656] Info fld=0x0 Jul 19 23:28:16 media kernel: [260151.912657] sd 11:0:0:1: [sdc] Add. Sense: Invalid field in cdb Jul 19 23:28:16 media kernel: [260151.912660] sd 11:0:0:1: [sdc] CDB: Read(10): 28 20 00 00 00 00 00 00 08 00 Jul 19 23:28:16 media kernel: [260151.912876] xhci_hcd 0000:03:00.0: WARN: Stalled endpoint Jul 19 23:28:16 media kernel: [260151.913439] sd 11:0:0:1: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE Jul 19 23:28:16 media kernel: [260151.913442] sd 11:0:0:1: [sdc] Sense Key : Illegal Request [current] Jul 19 23:28:16 media kernel: [260151.913445] Info fld=0x0 Jul 19 23:28:16 media kernel: [260151.913446] sd 11:0:0:1: [sdc] Add. Sense: Invalid field in cdb Jul 19 23:28:16 media kernel: [260151.913449] sd 11:0:0:1: [sdc] CDB: Read(10): 28 20 00 00 00 00 00 00 08 00 Jul 19 23:28:16 media kernel: [260151.945227] xhci_hcd 0000:03:00.0: WARN: Stalled endpoint Jul 19 23:28:16 media kernel: [260151.945863] sd 11:0:0:1: [sdc] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE Jul 19 23:28:16 media kernel: [260151.945866] sd 11:0:0:1: [sdc] Sense Key : Illegal Request [current] Jul 19 23:28:16 media kernel: [260151.945870] Info fld=0x0 Jul 19 23:28:16 media kernel: [260151.945871] sd 11:0:0:1: [sdc] Add. Sense: Invalid field in cdb Jul 19 23:28:16 media kernel: [260151.945875] sd 11:0:0:1: [sdc] CDB: Read(10): 28 20 00 00 00 00 00 00 08 00 (...) and so on for like 10 seconds until it gives up (...) 3. Question So, my question would be: what is causing this? Am I missing something, should I configure things differently, is this a known limitation? Searching online for more information did not yield any useful results... Thank you in advance for any help!

  Read the article

• Verification of files on backup media - after the backup

  - by Greg Sansom

  I have a system in place where I back up my work files daily to a portable hard drive. I actually have two portable hard drives - one is stored off-site and I swap them regularly. I also keep my family photos and other historical files backed up, but I only back the photos up occasionally (ie when I have new photos). The backup media is for backup only, and it is unlikely I will ever read the files from the backup media unless a disaster occurs and I lose the master. It worries me that my backed up files could become corrupt without me knowing it. It is also feasible that my master files could become corrupt, and eventually the corrupt files would be replicated to the backup media. I'm currently using Cobian Backup, but I'm open to alternatives. Is there a tool I can use to confirm that the backed up files are identical to the files that were first copied? I know it would be possible to generate a checksum and periodically validate the backup files against the original checksum, but I'm looking for a tool which will do this automatically.

  Read the article

• OSX 10.6.6 SSH md5 break-in check

  - by Alex

  Information Recently one of the linux servers that I access was compromised to steal passwords and ssh keys using a modified ssh binary. This lead me to question if the attacker had compromised my OSX Laptop which had ssh access turned on. A sophos virus scan turned up nothing, and I did not have rkhunter installed before the attack, so I could not compare hashes of the system binaries to be sure. However because OSX is relatively standard for each of their major releases, I asked fiends for md5 hashes md5 /usr/bin/ssh and md5 /usr/sbin/sshd as a basic first check to see if there was anything different about my machine. A few emails later I have found the following data: Version (Arch) [N] MD5 (/usr/bin/ssh) MD5 (/usr/sbin/sshd) OSX 10.5.8 (PPC) [3] 1e9fd483eef23464ec61c815f7984d61 9d32a36294565368728c18de466e69f1 OSX 10.5.8 (intel) [5] 1e9fd483eef23464ec61c815f7984d61 9d32a36294565368728c18de466e69f1 OSX 10.6.x (intel) [7] 591fbe723011c17b6ce41c537353b059 e781fad4fc86cf652f6df22106e0bf0e OSX 10.6.x (intel) [4] 58be068ad5e575c303ec348a1c71d48b 33dafd419194b04a558c8404b484f650 Mine 10.6.6 (intel) df344cc00a294c91230c65e8b7332a79 b5094ccf4cd074aaf573d4f5df75906a where N is the number of machines with with that MD5, and the last row is my laptop. The sample is relatively heterogeneous spaning a few years of different makes and models of Apples, and different versions of 10.6.x. The different hash for my system made me worried that these binaries might have been compromised. So I made sure that my backup for the week was good, and dived into formatting my system and reinstalling OSX. After reinstalling OSX from the manufacturer DVD, I found that the MD5 hash did not change for either ssh, or sshd. Goal Make sure that my system is does not have any malicious software. Should I be worried that this base install of OSX (with no other software installed) has been compromised? I have also updated my system to 10.6.6 and found no change as well. Other Information I am not sure if this is helpful information, but my laptop is a i7 15 inch MacBook Pro bought in Nov 2010, and here is some output from system_profiler: System Software Overview: System Version: Mac OS X 10.6.6 (10J567) Kernel Version: Darwin 10.6.0 64-bit Kernel and Extensions: No Time since boot: 1:37 Hardware: Hardware Overview: Model Name: MacBook Model Identifier: MacBook6,2 Processor Name: Intel Core i7 Processor Speed: 2.66 GHz Number Of Processors: 1 Total Number Of Cores: 2 L2 Cache (per core): 256 KB L3 Cache: 4 MB Memory: 4 GB Processor Interconnect Speed: 4.8 GT/s Boot ROM Version: MBP61.0057.B0C SMC Version (system): 1.58f16 Sudden Motion Sensor: State: Enabled On the laptop, I find: $ codesign -vvv /usr/bin/ssh /usr/bin/ssh: valid on disk /usr/bin/ssh: satisfies its Designated Requirement $ codesign -vvv /usr/sbin/sshd /usr/sbin/sshd: valid on disk /usr/sbin/sshd: satisfies its Designated Requirement $ ls -la /usr/bin/ssh -rwxr-xr-x 1 root wheel 1001520 Feb 11 2010 /usr/bin/ssh $ ls -la /usr/sbin/sshd -rwxr-xr-x 1 root wheel 1304800 Feb 11 2010 /usr/sbin/sshd $ ls -la /sbin/md5 -r-xr-xr-x 1 root wheel 65232 May 18 2009 /sbin/md5 Update So far I have not gotten an answer about this question, but if you could help by increasing the number of hashes that I can compare against, that would be great. To get hashes, and version numbers, run the following on osx: md5 /usr/bin/ssh md5 /usr/sbin/sshd ssh -V sw_vers

  Read the article

• Low CPU performance with low usage and clock - Windows 8.1

  - by Daniele

  I recently deleted everything from my PC and reinstalled Windows 8.1 from scratch. When I first booted into Windows everything was extremely slow though the CPU usage was very low (about 1%). After installing some drivers the problem seemed to be solved, I was able to use my PC normally. Today I installed a game and I noticed a strange behavior: the game was playable but the performance worsened more and more in the time. This is the situation BEFORE opening the game (normal): This is AFTER some minutes inside the game (low CPU usage and clock): Some information about my system: PC: Sony Vaio S13 (SVS13A1C5E) OS: Windows 8.1 CPU: Intel Core i7-3520M 2.90GHz GPU(1): Intel HD Graphics 4000 GPU(2): NVIDIA GeForce GT 640M LE I tried searching for new drivers and other solutions but noting worked and I don't know what is the cause. I did not checked the temperatures but the fans are not running fast and the PC does not look overheated. Update: Max CPU Temp: 66°C, Max GPU Temp: 61°C The strange thing is that the GPU load is 99% (GPU-Z) and the fan is almost silent. Update 2: I had troubles with Sony Vaio software, I can't get the FN keys and the STAMINA/SPEED switch to work (it is a physical switch to enable/disable the Nvidia card and change the Power Profile). I'm saying this because I remember that before reinstalling Windows there was an option in the Vaio Control Center (now it is not there anymore) that allowed me to choose from something like "priority to performance (ventilation)" or "priority to silence". The current behavior looks like a "priority to silence", but I can't get the stamina-speed switch to work and so I don't see similar oprions in the Vaio Control Center. I don't know if the problem is related to this.

  Read the article

• 8051 MCU debug board function

  - by b-gen-jack-o-neill

  Hi, in school I have written many programs for 8051 compatible CPU. But I never actually knew how our "debug" sets worked. I mean, we test our programs in special sets, which actually allow you to very simply load program to CPU via PC serial port. But I thing you know this musch more better than I. But how it works? I mean, I know there is chip which adjusts signal level from PC serial port to TTL logic, and than connected to serial line of 8051. But thats all I know. Actually even my teacher doesen´t know how it works, since school bought it all. So, I suspect there is some program already running in the 8051 which handles communication and stores your program into memory, am I right? But, how can you make 8051 to process instructions from different location than ROM? Becouse if I am right, you cannot write into ROM memory by any instruction, as well as 8051 can only read instructions from ROM?

  Read the article

• linux passwords in configuration files

  - by user33124

  Some programs on linux that use configuration files, want me to enter my password in plain text in one of their configuration files. For example newsbeauter, the rss reader wants me to enter my google account password in a ~/.newsbeauter/config if I want to read google reader feeds. Mutt also sort of wants a password in a text file, but gives an option of entering it on every login. Is there any secure workaround to storing a password in a config file like that (eg for newsbeauter)? I was thinking of running the app as root, but that doesn't seem right. Or somehow creating and deleting the file everytime I use the app. Any ideas?

  Read the article

• Getting back to Dreamweaver CS4?

  - by Chris_45

  My problem is that I want to assign a keyboardshortcut for Dreamweaver CS4 and I have it like this: "C:\Program Files\Adobe\Adobe Dreamweaver CS4\Dreamweaver.exe" Thats ok so far. But when I press the key it doesn't place itself infront of everything else like Outlook and Visual Studio does for example, instead it blinks in the taskbar, and I have to click there anyway to get back to Dreamweaver. Is there any switch or something I can assign for Dreamweaver to get back AND have it "popup?"

  Read the article

• Wifi network undetectable on a Lenovo G470

  - by Rex

  I have a WPA2 secured network with a visible SSID at home that works perfectly fine with a Dell laptop,a HP netbook and sundry mobile phones. When I try connecting my sister's Lenovo G470, it refuses to detect the wifi network no matter what, but shows up the neighbors' networks. The Lenovo also works correctly at her office. Both laptops run Windows 7. Already tried/checked the following: Manually configure wifi network settings (copied over from the Dell) Ensure there is no MAC address filtering on the router. Ensure router DHCP server is not running out of addresses to assign (I have set it to allocate upto 10). Reboot laptop, router etc. Is this a known problem, and is there anything else one could try? Update - The problematic Lenovo uses Windows 7 Home Basic while the Dell that works uses Home Premium and the HP netbook uses Starter edition - if that makes any difference. Further update - It is able to connect if I reboot into safe mode with networking. However in 'normal' mode it shows up the network sporadically, and then says there was an error connecting to it. All the network parameters, password, encryption, etc etc are EXACTLY the same as they are on the Dell.

  Read the article

• Adobe Reader unusably slow on Mac OS X 10.6.6

  - by vwegert

  We've got two Macs that are both running 10.6.6. On my MBP, Adobe (Acrobat) Reader started behaving weird a few weeks ago. It became very sluggish, started missing mouse clicks or mouse button releases, scrolling was next to impossible. Most of the time it does not handle Page Up / Page Down events at all. Zooming works erratically if at all. It's basically unusable. On the other Mac (an iMac), there are no such problems. I've tried to remove and reinstall Adobe Reader as well as upgrading to the latest version, but unfortunately without success. This is the only software that is behaving strangely on this Mac, everything else is working fine. What else could I try?

  Read the article

• Replacement mouse "feet"?

  - by Jeff Atwood

  The plastic skid pad "feet" on the bottom of my Logitech G9 mouse (which I love!) are getting rather worn down -- to the point that the outer shell of the mouse scrapes on the mousepad a bit. I've had the mouse for about ~2 years now so it does get a lot (I mean lot of use). But, I hate to buy a new mouse when I only need replacement "feet". Where can I obtain replacement mouse feet? Is this even possible?

  Read the article

• Anyone know how to get dual screens working on a Dell E6410 laptop with Ubuntu 10.04 64 bit?

  - by Curtis

  I've installed the drivers from nVidia. When I go into the NVIDIA X Server Settings application, in the X Server Display Configuration setcion, and click the "Configure" button, "TwinView" is disabled. Also, clicking "Detect Displays" doesn't pick up my monitor (which is connected through a port replicator - keyboard and mouse in that port replicator work fine). Has anyone else seen this? Is this just a limitation of the current nvidia linux drivers?

  Read the article

• Migrate installation from one HDD to another?

  - by dougoftheabaci

  I have a server with a 64 GB SSD inside. It runs just fine, but occasionally there's a hiccup that causes it to nearly fill up. When that happens my server starts to lockup and generally misbehave. I'm looking to buy a bigger SSD (either 128 GB or 256 GB) but I'm a bit unsure of how best to make the transition. For a start, I don't have an external monitor. If I need one I'll have to borrow it from work. Most of the time I just SSH into the server from my iMac. The only solution I can think of would be to buy two FW800 2.5" cases, boot from the 64 GB SSD and clone it to the 128 GB SSD. Seem a bit excessive but it might be my best option. I do have more than one SATA port on my server, but they're all currently being use for storage drives. They don't mount by default, so I could unplug them and just have the two SSDs and do the whole thing via SSH. This is another option I'm considering. My main concern with either is how best to make sure everything goes across. I want a carbon copy of the first one onto the second. This is especially important because I have a ZFS volume (my storage) and I'm a bit unfamiliar with how to move everything across. I could just start fresh and reinstall everything on the SSD, but that seems like extra trouble I don't need. So any advice on how best to achieve my goals would be appreciated. Thanks! Server is running Ubuntu Server 12.04. The iMac has 10.8.1.

  Read the article

• sudoers file cleanup and consolidation tool/script

  - by Prashanth Sundaram

  Hello All, I am curious to know what other folks out there might be using to keep the sudoers file in a sane manner. I am looking for a tool, that removes redundant entries, overlapping permissions and/or present sudoers file in a organized way(like sorting by permissions/users/Aliases). I use SVN and Confi Mgmt. tool to version control and deploy resp. Is there any add-on/plugin you would recommend/use? User_Alias RT1123 jappleseed, sjobs Host_Alias HOST_RT1123 wdc101.domain.com, wdc104.domain.com Cmnd_Alias ..... Our sudoers file is simple but a lot of entries and it needs to be cleaned up. Does anyone know/have a tool/script to fix/present it ? Thanks!

  Read the article

• Does a ext4 reader for Windows exist?

  - by zillion

  Is there any software or applications that can read ext4 from Windows?

  Read the article

• LaunchDaemon causing Lion to hang on boot

  - by Brett

  I've got a Mac Mini 2011, which I intend to use for a few tasks such as Plex and running a few VM's. I've installed virtualbox, along with XAMPP and phpvirtualbox, which all worked fine. However, getting this to run on startup is proving a real PITA! I'm at the moment trying to get vboxwebsrv running on boot. I've created a launchd plist within /Library/LaunchDaemons to run it and it works fine... well sort of. Lion when booting will show the spinning wheel and stop, never showing a GUI - however if I remote in via screen sharing or SSH, I can login fine and see that vboxwebsrv has launched successfully. Setting this plist to disabled makes lion boot up fine again. Initially I thought it was due to it staying open, so tried to add -b which causes it to run in the background, this just caused launchd to constantly spawn new processes and didn't even fix my problem of Lion being stuck at the spinning wheel. Does anyone have any ideas? I'm losing my mind here! PLIST: <?xml version="1.0" encoding="UTF-8"?> <!DOCTYPE plist PUBLIC "-//Apple//DTD PLIST 1.0//EN" "http://www.apple.com/DTDs/PropertyList-1.0.dtd"> <plist version="1.0"> <dict> <key>Disabled</key> <false/> <key>KeepAlive</key> <false/> <key>UserName</key> <string>vbox</string> <key>RunAtLoad</key> <true/> <key>OnDemand</key> <false/> <key>Label</key> <string>org.virtualbox.vboxwebsvc</string> <key>ProgramArguments</key> <array> <string>/Applications/VirtualBox.app/Contents/MacOS/vboxwebsrv</string> </array> </dict> </plist>

  Read the article

• Having problems install py2app 0.5.2

  - by Francis Young

  Hi there, I am a beginner at python so please excuse me for silly comments or rookie mistakes that i make. I was trying to install py2app 0.5.2 and i hit an error: $Best match: altgraph 0.7.1 $Downloading http://pypi.python.org/packages/source/a/altgraph/altgraph-$0.7.1.tar.gz#md5=f65988bf153410a8514bcdad6a3a8ba6 $Processing altgraph-0.7.1.tar.gz $Running altgraph-0.7.1/setup.py -q bdist_egg --dist-dir /tmp/easy_install-GGBuKJ/altgraph-$\0.7.1/egg-dist-tmp-NdWVjC $error: doc/changelog.rst: No such file or directory I was wondering what the solution to this problem is?

  Read the article

• Developer's PC - worth getting more than 8GB RAM?

  - by Borek

  I'm building a developer PC and am wondering whether to get 8GB or 12GB. It's a Core-i7 860 system, i.e., 1156 motherboards with 4 slots for RAM sticks, dual channel, usually up 16GB (as opposed to 1366 sockets where 6 banks / triple-channel are used). 8GB would be cheaper to get especially because price per GB is lower with 4x2GB compared to 2x4GB. Also the availability is worse for 4GB DIMMs here where I live; those are the main practical advantages of 8GB. (Edit: I should have stressed the price difference more - in the eshop I'm buying from, the difference between 12GB and 8GB is so big that I could almost buy a whole new netbook for it.) However, I understand that more RAM can never do harm which is the point of this question - how much of a difference will 12GB make as opposed to 8GB? Honestly, I've always been on 3.2GB systems (4GB but 32bit system) and never felt much pain from having too little memory - of course there could be more but for instance compiler's performance was usually held back by slow I/O or not utilizing multiple cores on my CPU. Still, I'm not questioning that 8GB will be useful, however, I'm not sure about the additional 4GB difference between 8 and 12 gig. Anyone has experience with 8GB / 12GB systems? The software I usually run all the time: Visual Studio or Eclipse (both should be fine with ~2GB RAM, after that I feel their performance is I/O bound) Firefox (it can never have enough RAM can it? :) Office (~500MB RAM should be enough) ... and then some smaller apps like Skype, other browsers, some background services etc.

  Read the article

• Move Emails Easily Using Search - Outlook 2011 Feature on the MAC for Outlook 2010 Windows

  - by Arthor

  My main email client is Outlook 2010 for Windows 7. I also have a Mac but I do not use it that much however on the MAC you have Outlook 2011. In my Outlook 2010 for Windows 7, I have many many folders. There is one feature I would like to know if it is available or something similar which is on Outlook 2011 for the Mac. On the Outlook 2011 for the mac you can go to: Top Menu Message Move Choose Folder or press (SHIT+CMD "press" M) This bring up a box where you can just type the beginning part of the folder and all the folders with that beginning appears (To search), you select the one you want and the selected emails move to that folder. I hope I have explained it well. Does anyone know if there is a plugin on Outlook 2010 or may I have just missed the function. Thank you

  Read the article

• problem when view the super block in ext3 file system

  - by xuczhang

  I tried to view the superblock by command "dd" in ext3 file system. dd if=/dev/sda3 bs=4096 skip=1 count=1 of=superblock But the result in superblock file is not correct(I compare the value of Inodes count I got from dumpe2fs). The device file /dev/sda3 is started at the boot block and then the superblock of the group0? And another question is the boot block and superblock's size are both BLOCKSIZE(here is 4096)? The disk format of ext2/ext3(I think they are the same) are shown below:

  Read the article

• Firewire 800 data transfer too slow on Macbook Pro Unibody and Win7 RC

  - by dtmunir

  I'm trying to back up some data on an external hard drive and am finding the transfer rate to be unbearably slow. My environment is as follows: Macbook Pro Unibody (late 2008) Windows 7 RC, 64-bit Lacie, rugged 500GB portable hard drive I have tried using a number of methods including simple copying in Explorer, Teracopy, Crashplan, and Windows backup. I am averaging around 1MB/s which seems terribly slow. How do I identify what is the cause of this slow file transfer, and then how do I go about addressing the issue.

  Read the article

< Previous Page | 584 585 586 587 588 589 590 591 592 593 594 595  | Next Page >