Search Results

Search found 1861 results on 75 pages for 'loss'.

Page 59/75 | < Previous Page | 55 56 57 58 59 60 61 62 63 64 65 66  | Next Page >

• C: 8x8 -> 16 bit multiply precision guaranteed by integer promotions?

  - by craig-blome

  I'm trying to figure out if the C Standard (C90, though I'm working off Derek Jones' annotated C99 book) guarantees that I will not lose precision multiplying two unsigned 8-bit values and storing to a 16-bit result. An example statement is as follows: unsigned char foo; unsigned int foo_u16 = foo * 10; Our Keil 8051 compiler (v7.50 at present) will generate a MUL AB instruction which stores the MSB in the B register and the LSB in the accumulator. If I cast foo to a unsigned int first: unsigned int foo_u16 = (unsigned int)foo * 10; then the compiler correctly decides I want a unsigned int there and generates an expensive call to a 16x16 bit integer multiply routine. I would like to argue beyond reasonable doubt that this defensive measure is not necessary. As I read the integer promotions described in 6.3.1.1, the effect of the first line shall be as if foo and 10 were promoted to unsigned int, the multiplication performed, and the result stored as unsigned int in foo_u16. If the compiler knows an instruction that does 8x8-16 bit multiplications without loss of precision, so much the better; but the precision is guaranteed. Am I reading this correctly? Best regards, Craig Blome

  Read the article

• Do complex JOINs cause high coupling and maintenance problems ?

  - by ashkan.kh.nazary

  Our project has ~40 tables with complex relations.A colleague believes in using long join queries which enforces me to learn about tables outside of my module but I think I should not concern about tables not directly related to my module and use data access functions (written by those responsible for other modules) when I need data from them. Let me clarify: I am responsible for the ContactVendor module which enables the customers to contact the vendor and start a conversation about some specific product. Products module has it's own complex tables and relations with functions that encapsulate details (for example i18n, activation, product availability etc ...). Now I need to show the product title of some product related to some conversation between the vendor and customers. I may either write a long query that retrieves the product info along with conversation stuff in one shot (which enforces me to learn about Product tables) OR I may pass the relevant product_id to the get_product_info(int) function. First approach is obviously demanding and introduces many bad practices and things I normally consider fault in programming. The problem with the second approach seems to be the countless mini queries these access functions cause and performance loss is a concern when a loop tries to fetch product titles for 100 products using functions that each perform a separate query. So I'm stuck between "don't code to the implementation, code to interface" and performance. What is the right way of doing things ? UPDATE: I'm specially concerned about possible future modifications to those tables outside of my module. What if the Products module decided to change the way they are doing things? or for some reason modify the schema? It means some other modules would break or malfunction until the change is integrated to them. The usual ripple effect problem.

  Read the article

• Is there a way to toggle bluetooth and/or wifi on and off programatically in iOS?

  - by Andy W

  I am looking for an easy way to toggle both bluetooth and wifi between on and off states on iOS 4.x devices (iPhone and iPad). I am constantly toggling these functions as I move between different locations and usage scenarios, and right now it takes multiple taps and visits to the Settings App. I am looking to create a simple App, that lives on Springboard, that I can just tap and it will turn off the wifi if it's on, and vice versa, then immediately quit. Similarly with an App for toggling bluetooth’s state. I have the developer SDK, and am comfortable in Xcode and with iOS development, so am happy to write the required Xcode to create the App. I am just at a loss as to which API, private or not, has the required functionality to simply toggle the state of these facilities. Because this is scratching a very personal itch, I have no intent to try and sell the App or get it up on the App store, so conforming with App guidelines on API usage is a non-issue. What I don’t want to do is jailbreak the devices, as I want to keep the core software as shipped. Can anyone point me at some sample code or more info on achieving this goal, as my Google-fu is letting me down, and if the information is out there for 4.x devices I just can’t find it.

  Read the article

• My Android XML files can't find ActionBarSherlock themes

  - by MalcolmMcC

  I'm trying to develop an app with ActionBarSherlock and everything works except the theming. Specifically, I can import com.actionbarsherlock.app.*, extend SherlockActivity, but I always have this error in my manifest: Error: No resource found that matches the given name (at 'theme' with value '@style/Theme.Sherlock'). I know there have been plenty of questions asked about this, but they have not worked for me. I have tried refreshing the workspace cleaning all of my projects putting the line in both the <activity> and the <application> setting my targetSdkVersion and minSdkVersion to various values, in both my manifest and ABS's and I've tried the following variations, and probably others: android:theme="@style/Theme.Sherlock" android:theme="@android:style/Theme.Sherlock" theme="@style/Theme.Sherlock" theme="@android:style/Theme.Sherlock" theme="@theme/Theme.Sherlock" theme="@android:theme/Theme.Sherlock" It's worth noting that the autocomplete after I typed "@style/" was showing nothing, so I tried making my own style in styles.xml and then that showed up but still nothing from ActionBarSherlock. Also, in styles.xml, I tried to make my own theme to extend Theme.Sherlock, and @style/Theme.Sherlock was not found there either when I tried to add it as a parent. I tried loading the samples but got a JAR Mismatch. My conclusion is that somehow my xml files are unable to access the ABS library, but I'm at a loss as to how to fix it. Any help hugely appreciated.

  Read the article

• Passing filtering functions to Where() in LINQ-to-SQL

  - by Daniel

  I'm trying to write a set of filtering functions that can be chained together to progressively filter a data set. What's tricky about this is that I want to be able to define the filters in a different context from that in which they'll be used. I've gotten as far as being able to pass a very basic function to the Where() clause in a LINQ statement: filters file: Func<item, bool> returnTrue = (i) => true; repository file: public IQueryable<item> getItems() { return DataContext.Items.Where(returnTrue); } This works. However, as soon as I try to use more complicated logic, the trouble begins: filters file: Func<item, bool> isAssignedToUser = (i) => i.assignedUserId == userId; repository file: public IQueryable<item> getItemsAssignedToUser(int userId) { return DataContext.Items.Where(isAssignedToUser); } This won't even build because userId isn't in the same scope as isAssignedToUser(). I've also tried declaring a function that takes the userId as a parameter: Func<item, int, bool> isAssignedToUser = (i, userId) => i.assignedUserId == userId; The problem with this is that it doesn't fit the function signature that Where() is expecting: Func<item, bool> There must be a way to do this, but I'm at a loss for how. I don't feel like I'm explaining this very well, but hopefully you get the gist. Thanks, Daniel

  Read the article

• CEIL is one too high for exact integer divisions

  - by Synetech

  This morning I lost a bunch of files, but because the volume they were one was both internally and externally defragmented, all of the information necessary for a 100% recovery is available; I just need to fill in the FAT where required. I wrote a program to do this and tested it on a copy of the FAT that I dumped to a file and it works perfectly except that for a few of the files (17 out of 526), the FAT chain is one single cluster too long, and thus cross-linked with the next file. Fortunately I know exactly what the problem is. I used ceil in my EOF calculation because even a single byte over will require a whole extra cluster: //Cluster is the starting cluster of the file //Size is the size (in bytes) of the file //BPC is the number of bytes per cluster //NumClust is the number of clusters in the file //EOF is the last cluster of the file’s FAT chain DWORD NumClust = ceil( (float)(Size / BPC) ) DWORD EOF = Cluster + NumClust; This algorithm works fine for everything except files whose size happens to be exactly a multiple of the cluster size, in which case they end up being one cluster too much. I thought about it for a while but am at a loss as to a way to do this. It seems like it should be simple but somehow it is surprisingly tricky. What formula would work for files of any size?

  Read the article

• Django Querysets -- need a less expensive way to do this..

  - by rh0dium

  Hi all, I have a problem with some code and I believe it is because of the expense of the queryset. I am looking for a much less expensive (in terms of time) way to to this.. log.info("Getting Users") employees = Employee.objects.filter(is_active = True) log.info("Have Users") if opt.supervisor: if opt.hierarchical: people = getSubs(employees, " ".join(args)) else: people = employees.filter(supervisor__name__icontains = " ".join(args)) else: log.info("Filtering Users") people = employees.filter(name__icontains = " ".join(args)) | \ employees.filter(unix_accounts__username__icontains = " ".join(args)) log.info("Filtered Users") log.info("Processing data") np = [] for person in people: unix, p4, bugz = "No", "No", "No" if len(person.unix_accounts.all()): unix = "Yes" if len(person.perforce_accounts.all()): p4 = "Yes" if len(person.bugzilla_accounts.all()): bugz = "Yes" if person.cell_phone != "": exphone = fixphone(person.cell_phone) elif person.other_phone != "": exphone = fixphone(person.other_phone) else: exphone = "" np.append({ 'name':person.name, 'office_phone': fixphone(person.office_phone), 'position': person.position, 'location': person.location.description, 'email': person.email, 'functional_area': person.functional_area.name, 'department': person.department.name, 'supervisor': person.supervisor.name, 'unix': unix, 'perforce': p4, 'bugzilla':bugz, 'cell_phone': fixphone(exphone), 'fax': fixphone(person.fax), 'last_update': person.last_update.ctime() }) log.info("Have data") Now this results in a log which looks like this.. 19:00:55 INFO phone phone Getting Users 19:00:57 INFO phone phone Have Users 19:00:57 INFO phone phone Processing data 19:01:30 INFO phone phone Have data As you can see it's taking over 30 seconds to simply iterate over the data. That is way too expensive. Can someone clue me into a more efficient way to do this. I thought that if I did the first filter that would make things easier but seems to have no effect. I'm at a loss on this one. Thanks To be clear this is about 1500 employees -- Not too many!!

  Read the article

• Form With Quantity doesn't seem to submit

  - by Karl Entwistle

  Hey guys, I've been trying to understand the documentation and find an example, but I'm at a loss. This is just a submit form within the cart for updating the quantity. However, the updated quantity is not getting saved to the database -- it always makes the quantity 0. Please help. Form <% for line_item in @cart.line_items %> <% form_for :lineitems, :url => {:controller => "line_items", :action => "cart_update", :id => "#{line_item.product_id}"} do |l| %> <%= l.text_field :quantity, :size => '3', :value => line_item.quantity %> <%= l.submit 'cart_update' %> <% end %> Route map.connect 'line_item_update', :controller => 'line_items', :action => 'cart_update' Controller def cart_update @product = Product.find(params[:id]) item = LineItem.find_or_create_by_cart_id(:cart_id => current_cart.id, :product_id => @product.id, :quantity => 0, :unit_price => @product.price) item.quantity = (params[:quantity]).to_i item.save redirect_to :controller => 'products' end

  Read the article

• Querying a 3rd party website's database from my website

  - by Mong134

  The Goal: To retrieve information from a 3rd party database based off of a user's query on my ASP.NET website The Details: I need to be able to search 3rd-party websites for information relating to pharmaceutical drugs. Basically, here's what I've been tasked with: a user starts entering the name of a drug they're using in their experiments, and while they're typing a 3rd party website (e.g., here or here) is queried and suggestions are made based based off of what they've typed. Once they've made a selection, certain properties (molecular weight, chemical structure, etc) are retrieved from the 3rd party database and stored in our database. PharmaGKB.org's search bar is pretty much what I need to implement, but I need to access a 3rd party db. The site that I'm working on is ASP.NET/C#. The Problem: I don't really know where to start with this. There's a downloadable Perl example at the bottom of the page here, but it didn't really help me all that much. I'm at a loss as to how to implement this, or even find information about how to do it. The AJAX toolkit was suggested, but I'm not sure if that will solve the issue. JavaScript is also being considered, but again, I'm not sure if that will be sufficient, either. Perl Example Connection As a mentioned, here is a snippet from the Perl example given on the Pharmgkb.org site: my $call = SOAP::Lite -> readable (1) -> uri('SearchService') -> proxy('http://www.pharmgkb.org/services/SearchService') -> search ($ARGV[0]); However, I'm not sure how to implement this is C#/ASP.NET/JavaScript. There's a question on Stack Overflow about embedding Perl in C#, but it require a C wrapper as well, and I don't think that three languages is necessary or wise to solve this issue.

  Read the article

• Which source control paradigm and solution to embed in a custom editor application?

  - by Greg Harman

  I am building an application that manages a number of custom objects, which may be edited concurrently by multiple users (using different instances of the application). These objects have an underlying serialized representation, and my plan is to persist them (through my application UI) in an external source control system. Of course this implies that my application can check the current version of an object for updates, a merging interface for each object, etc. My question is what source control paradigm(s) and specific solution(s) to support and why. The way I (perhaps naively) see the source control world is three general paradigms: Single-repository, locked access (MS SourceSafe) Single-repository, concurrent access (CVS/SVN) Distributed (Mercurial, Git) I haven't heard of anyone using #1 for quite a number of years, so I am planning to disregard this case altogether (unless I get a compelling argument otherwise). However, I'm at a loss as to whether to support #2 or #3, and which specific implementations. I'm concerned that the use paradigms are subtly different enough that I can't adequately capture basic operations in a single UI. The last bit of information I should convey is that this application is intended to be deployed in a commercial setting, where a source control system may already be in use. I would prefer not to support more than one solution unless it's really a deal-breaker, so wide adoption in a corporate setting is a plus.

  Read the article

• How to set ReceiveBufferSize for UDPClient? or Does it make sense to set? C#

  - by Jack

  Hello all. I am implementing a UDP data transfer thing. I have several questions about UDP buffer. I am using UDPClient to do the UDP send / receive. and my broadband bandwidth is 150KB/s (bytes/s, not bps). I send out a 500B datagram out to 27 hosts 27 hosts send back 10KB datagram back if they receive. So, I should receive 27 responses, right? however, I only get averagely 8 - 12 instead. I then tried to reduce the size of the response down to 500B, yes, I receive all. A thought of mine is that if all 27 hosts send back 10KB response at almost same time, the incoming traffic will be 270KB/s (likely), that exceeds my incoming bandwidth so loss happens. Am I right? But I think even if the incoming traffic exceeds the bandwidth, is the Windows supposed to put the datagram in the buffer and wait for receive? I then suspect that maybe the ReceiveBufferSize of my UdpClient is too small? by default, it is 8092B?? I don't know whether I am all right at these points. Please give me some help.

  Read the article

• Interactive World Map, highlight countries on mouseover

  - by BrenGG

  I need to create an interactive world map on the front page of a site, the view portal will be about 650x200 pixels. The interactivity would include the following, mouse-over a country would highlight (the countries are will literally be filled with "red" for example) that country and display the countries' name (preferably text in a div), I will also be linking the highlighting event with a that will highlight a country when selected. I am having a difficult time finding a suitable solution, I refuse to use or learn a proprietry technology such as flash so it is not an option. I created a simple mockup using openlayers and a custom map image but the countries' markers load too slowly in IE6. Also svg seems too large, as I tried to use RaphaelJS, but abondoned it when I realised the world map data is 1.2mb which is totally un acceptable for the front page of a site.. I am really at a loss on how I am going to do this, my last resort is to manually create 250+ (however many countries there are) pngs and apply mouseover events to hotspots in the image... but this is probably going to be a dead end too.. desperately seeking a solution, any helpful comments will be appreciated!

  Read the article

• Using generics in F# to create an EnumArray type

  - by Matthew

  I've created an F# class to represent an array that allocates one element for each value of a specific enum. I'm using an explicit constructor that creates a dictionary from enum values to array indices, and an Item property so that you can write expressions like: let my_array = new EnumArray<EnumType, int> my_array.[EnumType.enum_value] <- 5 However, I'm getting the following obscure compilation error at the line marked with '// FS0670' below. error FS0670: This code is not sufficiently generic. The type variable ^e when ^e : enum<int> and ^e : equality and ^e : (static member op_Explicit : ^e -> int) could not be generalized because it would escape its scope. I'm at a loss - can anyone explain this error? type EnumArray< 'e, 'v when 'e : enum<int> and 'e : equality and ^e : (static member op_Explicit : ^e -> int) > = val enum_to_int : Dictionary<'e, int> val a : 'v array new() as this = { enum_to_int = new Dictionary<'e, int>() a = Array.zeroCreate (Enum.GetValues(typeof<'e>).Length) } then for (e : obj) in Enum.GetValues(typeof<'e>) do this.enum_to_int.Add(e :?> 'e, int(e :?> 'e)) member this.Item with get (idx : 'e) : 'v = this.a.[this.enum_to_int.[idx]] // FS0670 and set (idx : 'e) (c : 'v) = this.a.[this.enum_to_int.[idx]] <- c

  Read the article

• How do you store accented characters coming from a web service into a database?

  - by Thierry Lam

  I have the following word that I fetch via a web service: André From Python, the value looks like: "Andr\u00c3\u00a9". The input is then decoded using json.loads: >>> import json >>> json.loads('{"name":"Andr\\u00c3\\u00a9"}') >>> {u'name': u'Andr\xc3\xa9'} When I store the above in a utf8 MySQL database, the data is stored like the following using Django: SomeObject.objects.create(name=u'Andr\xc3\xa9') Querying the name column from a mysql shell or displaying it in a web page gives: André The web page displays in utf8: <meta http-equiv="Content-Type" content="text/html; charset=utf-8" /> My database is configured in utf8: mysql> SHOW VARIABLES LIKE 'collation%'; +----------------------+-----------------+ | Variable_name | Value | +----------------------+-----------------+ | collation_connection | utf8_general_ci | | collation_database | utf8_unicode_ci | | collation_server | utf8_unicode_ci | +----------------------+-----------------+ 3 rows in set (0.00 sec) mysql> SHOW VARIABLES LIKE 'character_set%'; +--------------------------+----------------------------+ | Variable_name | Value | +--------------------------+----------------------------+ | character_set_client | utf8 | | character_set_connection | utf8 | | character_set_database | utf8 | | character_set_filesystem | binary | | character_set_results | utf8 | | character_set_server | utf8 | | character_set_system | utf8 | | character_sets_dir | /usr/share/mysql/charsets/ | +--------------------------+----------------------------+ 8 rows in set (0.00 sec) How can I retrieve the word André from a web service, store it properly in a database with no data loss and display it on a web page in its original form?

  Read the article

• Several Objective-C objects become Invalid for no reason, sometimes.

  - by farnsworth

  - (void)loadLocations { NSString *url = @"<URL to a text file>"; NSStringEncoding enc = NSUTF8StringEncoding; NSString *locationString = [[NSString alloc] initWithContentsOfURL:[NSURL URLWithString:url] usedEncoding:&enc error:nil]; NSArray *lines = [locationString componentsSeparatedByString:@"\n"]; for (int i=0; i<[lines count]; i++) { NSString *line = [lines objectAtIndex:i]; NSArray *components = [line componentsSeparatedByString:@", "]; Restaurant *res = [byID objectForKey:[components objectAtIndex:0]]; if (res) { NSString *resAddress = [components objectAtIndex:3]; NSArray *loc = [NSArray arrayWithObjects:[components objectAtIndex:1], [components objectAtIndex:2]]; [res.locationCoords setObject:loc forKey:resAddress]; } else { NSLog([[components objectAtIndex:0] stringByAppendingString:@" res id not found."]); } } } There are a few weird things happening here. First, at the two lines where the NSArray lines is used, this message is printed to the console- *** Terminating app due to uncaught exception 'NSInvalidArgumentException', reason: '*** -[NSCFDictionary count]: method sent to an uninitialized mutable dictionary object' which is strange since lines is definitely not an NSMutableDictionary, definitely is initialized, and because the app doesn't crash. Also, at random points in the loop, all of the variables that the debugger can see will become Invalid. Local variables, property variables, everything. Then after a couple lines they will go back to their original values. setObject:forKey never has an effect on res.locationCoords, which is an NSMutableDictionary. I'm sure that res, res.locationCoords, and byId are initialized. I also tried adding a retain or copy to lines, same thing. I'm sure there's a basic memory management principle I'm missing here but I'm at a loss.

  Read the article

• BASH echo write mysql input

  - by jmituzas

  Have a bash menu where variables write to file for mysql input. heres what I have: echo "CREATE DATABASE '$mysqldbn'; #GRANT ALL PRIVILEGES ON *.* TO '$mysqlu'@'$myhost' IDENTIFIED BY '$mysqlup' WITH GRANT OPTION; GRANT SELECT, INSERT, UPDATE, DELETE, CREATE, DROP, INDEX, ALTER, CREATE TEMPORARY TABLES, LOCK TABLES ON '$mysqldbn'.* TO '$mysqlu'@'$myhost' IDENTIFIED BY '$mysqlup'; GRANT SELECT, INSERT, UPDATE, DELETE, CREATE, DROP, INDEX, ALTER, CREATE TEMPORARY TABLES, LOCK TABLES ON '$mysqldbn'.* TO '$mysqlu'@'$myip' IDENTIFIED BY '$mysqlup'; GRANT SELECT, INSERT, UPDATE, DELETE, CREATE, DROP, INDEX, ALTER, CREATE TEMPORARY TABLES, LOCK TABLES ON '$mysqldbn'.* TO '$mysqlu'@'localhost' IDENTIFIED BY '$mysqlup'; GRANT SELECT, INSERT, UPDATE, DELETE, CREATE, DROP, INDEX, ALTER, CREATE TEMPORARY TABLES< LOCK TABLES on '$mysqldbn'.* TO '$mysqlu'@'$rip' IDENTIFIED BY '$mysqlup';" > nmysql.db mysql -u root -p$mypass < nmysql.db problem is to get variables to show I had to put them in single quotes, the single quotes show up as I want for instances like '$mysqlu'@'localhost'. But how can I remove the quotes and still get to use the variable in the instance like, CREATE DATABASE '$mysqldbn' ? Double quotes wont work either, I am at a loss. Thanks in advance, Joe

  Read the article

• Which JavaScript or ASP.NET Charting Component/Tool/Library Will Work For This?

  - by Jason Bunting

  [Update]: Forgot to include ComponentArt... Hi, An interaction designer employed by the client I am currently working for produced some mock-ups, and now it is my job to determine the best way of implementing the charts included therein. After looking at the options I am aware of and was able to find doing some simple Google searches, I have narrowed it down to using either ComponentArt, Dundas Charts or Infragistics, simply because from what I can see of their demos, they have certain features I believe I will need to get things done. Here are the pictures from the mock-ups - ideally I need one piece of software that will cover all of these: This chart seems to be simple enough. Notice the arbitrary spacing between the years - not yet sure if this will be a sticking-point for the client or not. I don't know that I have ever seen a chart like this one - it combines the previous chart with some additional data. Here is the same chart, only this time illustrating what happens when a user mouses-over or clicks on an annotation within the chart. They want the nice styling within the pop-up, so the pop-up needs to be something like an iframe or similar. Any ideas or recommendations would be appreciated, I haven't used charting controls in years, so I am at a bit of a loss and the client wants an estimate soon. Thank you!

  Read the article

• XSL - How to match consecutive comma-separated tags

  - by PocketLogic

  I'm trying to match a series of xml tags that are comma separated, and to then apply an xslt transformation on the whole group of nodes plus text. For example, given the following partial XML: <p>Some text here <xref id="1">1</xref>, <xref id="2">2</xref>, <xref id="3">3</xref>. </p> I would like to end up with: <p>Some text here ^1,2,3.</p> A much messier alternate would also be acceptable at this point: <p>Some text here ¹^,²^,³.</p> I have the transformation to go from a single xref to a sup: <xsl:template match="xref""> ^{<xsl:apply-templates/>} </xsl:template> But I'm at a loss as to how to match a group of nodes separated by commas. Thanks.

  Read the article

• Blogger Template: how to change the color of the border css

  - by Lirik

  Hi, I'm trying to change the borders in the style sheet of the template on my blog, but I've never done anything with css so I'm a little bit at a loss... I want to keep the dark background, but I want to create a small border with a slightly different color around my postings. If my guess is correct, then I should modify some of these definitions: body { background:$bgcolor; margin:0; color:$textcolor; font: x-small "Trebuchet MS", Trebuchet, Verdana, Sans-serif; font-size/* */:/**/small; font-size: /**/small; text-align: center; } a:link { color:$linkcolor; text-decoration:none; } a:visited { color:$visitedlinkcolor; text-decoration:none; } a:hover { color:$titlecolor; text-decoration:underline; } a img { border-width:0; } Here is a pastie with the entire template I'm using: http://pastie.org/932535 Is there a quick way to achieve the desired effect? Your help is appreciated!

  Read the article

• Existing parsers in c# (BSD license or similar)

  - by Sylverdrag

  I am looking for parsers (in C#) for a bunch of formats. (PHP, ASP, some XML based formats, HTML,...pretty much anything I can get my hands on.) The purpose is to separate the text from the code and do some edits without messing up the code. I had a look at ANTLR, but while it seems like the "right tool", there is just too much prior knowledge assumed. I have an easier time writing a parser from scratch than understanding how to "easily" generate parsers from ANTLR. (I wrote a small parser for a specific type of RTF files within a couple days, so the task is probably within my reach, but as I have no formal knowledge of parsing/lexing, I am at loss with ANTLR) Then it occurred to me that there must existing parsers for many formats, so before I start writing yet another a brand new and potentially buggy version of the wheel, I figured I would check what parsers already exist and can be reused in a commercial product. I could use parsers for just about every format in existence, so this question would be a good place to make a list of all existing free parsers written in C#, if there are any. Thanks in advance for your suggestions

  Read the article

• Cannot connect to SQL Server from ASP.NET MVC app

  - by Dan Fergus

  I have an ASP.NET MVC app that has on a hosted server for over a year, connecting to SQL Server. I've had to change hosting services, the new one supports MVC 1.0. I've also moved a non MVC ASP app to the same hosting service. Now, MY MVC based app retturnes this error when I try to validate a user login. A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: Named Pipes Provider, error: 40 - Could not open a connection to SQL Server) Now, the non-MVC app can access the exact same database and authenticate users just fine. The MVC app, when run from my dev box connects fine. It also run/connects/authenticates without problem when I install and run the site from an internal SQL 2008 server running IIS 7. I, along with the hosting support techs, am at a loss how the exact same connect string works every where except on the hosted server, and only when run from inside an ASP.NET MVC web app. Any ideas would be greatly appreciated.

  Read the article

• Rackspace Cloud rewrite jpg causes Session reset

  - by willoller

  This may be the .Net version of this question. I have an image script with the following: ... Response.WriteFile(filename); Response.End(); I am rewriting .jpg files using the following rewrite rule in web.config: <rule name="Image Redirect" stopProcessing="true"> <match url="^product-images/(.*).jpg" /> <conditions> <add input="{REQUEST_URI}" pattern="\.(jp?g|JP?G)$" /> </conditions> <action type="Redirect" redirectType="SeeOther" url="/product-images/ProductImage.aspx?path=product-images/{tolower:{R:1}}.jpg" /> </rule> It basically just rewrites the image path into a query parameter. The problem is that (intermittently of course) Mosso returns a new Asp Session cookie which breaks the whole world. Directly accessing a static .jpg file does not cause this problem. Directly accessing the image script does not cause it either. Only rewriting a .jpg file to the .aspx script causes the Session loss. Things I have tried (From the Rackspace doc How can I bypass the cache?) I added Private cacheability to the image script itself: Response.Cache.SetCacheability(HttpCacheability.Private); I tried adding these cache-disabling nodes to web.config: <staticContent> <clientCache cacheControlMode="DisableCache" /> </staticContent> and <httpProtocol> <customHeaders> <add name="Cache-Control private" value="Cache-Control private" </customHeaders> </httpProtocol> The Solution I need The browser cache cannot be disabled. This means potential solutions involving Cache.SetNoStore() or HttpCacheability.NoCache will not work.

  Read the article

• iPhone: detect "touch-and-drag" gesture from UIBarButtonItem?

  - by Greg Maletic

  I have an "add" button that's represented by a UIBarButtonItem. Hitting the "add" button adds an object into a list that represents a moment in time. By default, that time is "now"...but I'd like to be able to use dragging behavior to let the user specify earlier times for the object. Here's the behavior I want to implement: If the user touches on the UIBarButtonItem and lets go quickly, an object is added to the list that represents "now." If the user touches on the UIBarButtonItem and drags, a little UI pops up that shows the time that the distance of their drag represents. The further they drag, the further back in time their touch will represent. When they let go, the object representing an earlier time will get added to the list. (Though the description of the behavior is complicated, I'm convinced this will be pretty intuitive for users of the app.) I haven't implemented code for anything but the most simple touches in the past, and I'm at a loss as to the best way to try this. Does anyone have any suggestions, or could point me towards some sample code that implements something like this? Thanks very much.

  Read the article

• SPRING: How do you programmatically instantiate classes based on information passed from Flex UI

  - by babyangel86

  Imagine the UI passes back an XMl node as such: <properties> <type> Source </type> <name> Blooper </name> <delay> <type> Deterministic </type> <parameters> <param> 4 </param> </parameters> <delay> <batch> <type> Erlang </type> <parameters> <param> 4 </param> <param> 6 </param> </parameters> <batch> And behind the scene what it is asking that you instantiate a class as such: new Source("blooper", new Exp(4), new Erlang(4,6); The problem lies in the fact that you don't know what class you will need to processing, and you will be sent a list of these class definitions with instructions on how they can be linked to each other. I've heard that using a BeanFactoryPostProcessor might be helpful, or a property editor/convertor. However I am at a loss as to how best to use them to solve my problem. Any help you can provide will be much appreciated.

  Read the article

• Advice needed: cold backup for SQL Server 2008 Express?

  - by Mikey Cee

  What are my options for achieving a cold backup server for SQL Server Express instance running a single database? I have an SQL Server 2008 Express instance in production that currently represents a single point of failure for my application. I have a second physical box sitting at the installation that is currently doing nothing. I want to somehow replicate my database in near real time (a little bit of data loss is acceptable) to the second box. The database is very small and resources are utilized very lightly. In the case that the production server dies, I would manually reconfigure my application to point to the backup server instead. Although Express doesn't support log shipping, I am thinking that I could manually script a poor man's version of it, where I use batch files to take the logs and copy them across the network and apply them to the second server at 5 minute intervals. Does anyone have any advice on whether this is technically achievable, or if there is a better way to do what I am trying to do? Note that I want to avoid having to pay for the full version of SQL Server and configure mirroring as I think it is an overkill for this application. I understand that other DB platforms may present suitable options (eg. a MySQL Cluster), but for the purposes of this discussion, let's assume we have to stick to SQL Server.

  Read the article

< Previous Page | 55 56 57 58 59 60 61 62 63 64 65 66  | Next Page >