Search Results

Search found 18126 results on 726 pages for 'bsi support'.

Page 591/726 | < Previous Page | 587 588 589 590 591 592 593 594 595 596 597 598  | Next Page >

• My home box as my own host?

  - by Majid

  Hi all, I have a 512 kb/s DSL service at home. I do not have a static IP but I can get one if I pay some extra to my ISP. Now, if I get the static IP, can I make my home box act as my internet host? What else do I need? Thanks P.S. I know that if at all possible, the site I make available this way might be slow, that is alright, my question is if it is possible at all. Edit: I need this for very small traffic. I am a php developer and for my projects I am often asked to provide a demo. I currently use a free hosting for this purpose but it is down most of the time and support is non-existent. So I thought to set-up my home computer as my test server. With this please note that: I will only occasionally have 'visitors' and that will be one or possibly two visitors at any time. These demos, are to showcase functionality, so no big images are served and page views will normally generate under 100KB of traffic.

  Read the article

• Internet Troubles - PPPoE vs PPPoA?

  - by AkkA

  I have been having some internet troubles at home (ADSL2+ connection in Australia). We get random drop-outs from the authentication connection. It will keep the connection to the DSL service, but we lose authentication and either have to restart the router/modem (its combined, a Belkin one, not sure on model number) or unplug the phone cable, wait about 30 seconds and plug it in again. I've called the ISP (Telstra) a few times, but they only offer limited support when we dont use their supported hardware. Apparently something had happened on their side, they checked the box again (at least it sounded that simple), and told me it would be fine. It wasnt. I've replaced all the filters around the house, but that didnt help either. We do live a little bit away from the exchange (get a sync speed of about 3000/900), so I thought it could be due to line noise but that hasnt helped. Telstra allow both PPPoE and PPPoA connections (which I'm configuring through my router, dont have software on the PC side). I've been running PPPoA the whole time, would it make any difference changing it to PPPoE? If not, are there any other theories as to why we would be experiencing these drop-outs? It has been fine for at least 12 months, then suddenly started about 2 months ago.

  Read the article

• samba joined to AD canot see users when in the security tab on client

  - by Jonathan

  I've got samba joined via kerberos and winbindd to our AD network and user authentication and everything else is working great. However when I try to add users/groups to file permissions it tells me they are not found. All the users groups show up fine with getent so I'm not sure why they are not showing up. Here is my smb.conf and I would much appreciate any help with this. #GLOBAL PARAMETERS [global] socket options = TCP_NODELAY IPTOS_LOWDELAY SO_KEEPALIVE SO_RCVBUF=11264 SO_SNDBUF=11264 workgroup = [hidden] realm = [hidden] preferred master = no server string = xerxes web/file server security = ADS encrypt passwords = yes log level = 3 log file = /var/log/samba/%m max log size = 50 printcap name = cups printing = cups winbind enum users = Yes winbind enum groups = Yes winbind use default domain = Yes winbind nested groups = Yes winbind separator = + winbind refresh tickets = yes idmap uid = 1600-20000 idmap gid = 1600-20000 template primary group = "Domain Users" template shell = /bin/bash kerberos method = system keytab nt acl support = yes [homes] comment = Home Direcotries valid users = %S read only = No browseable = No create mask = 0770 directory mask = 0770 force create mode = 0660 force directory mode = 2770 inherit owner = no [test] comment = Test path=/mnt/test writeable=yes valid users = %s create mask = 0770 directory mask = 0770 force create mode = 0660 force directory mode = 2770 inherit owner = no [printers] comment = All Printers path = /var/spool/cups browseable = no printable = yes

  Read the article

• come on!teach u save photos from iphone to computer

  - by goodm

  i am using iphone ,when we have fun,we took a lot of nice pics ,but,that is a question,how to transfer photos from iphone to computer,now ,let me show you,step by step: Step 1: Download Tansee iPhone Transfer Photo free trial version here,and then install it. You also need iTunes above 7.3 installed.or download at: http://www.softseeking.com/prodail.aspx?proid=74 Step 2: Connect iPhone to your computer. Step 3: Launch Tansee iPhone Transfer Photo and all the photos in your iPhone will display automatically, Step 4: Select the photos to be transferred to your computer, the selected file will marked with red border. You can select photos by click on each one, or just drag a rectangle to select a bundle of photos. You can also select all photos by click right button of your mouse or click "File" to choose. Note: you can only select first 6 photos if you haven't purchase. Step 5: Click "Copy" button to select output path and start to transfer photos to your computer: iPhone Camera Photo & Camera Video: Click "Camera Roll", do as steps above can copy your iPhone Camera Photos and iPhone Camera Videos to PC. Options Setting 1.Backup File Format: To select backup photo file format, Tansee iPhone Transfer Photo support BMP and JPG file now. 2.Backup Path: To select directory for storing the backup photos. You can select backup directory for each photo during backup by check "Ask Every Time" or store all files in a specified directory by checking "Save Here" and select the directory in the edit box. 3.Backup Resolution: To select the photo size to be backup.

  Read the article

• Authentication required by wireless network

  - by Roman

  I would like to use a wireless network from Ubuntu. In the network drop-down menu I select a network (this is a University network I have an account there). Then I get a windows with the following fields: Wireless Security: [WPA&WPA2 Enterprise] Authentication: [Tunneled TLS] Anonymous Identity: [] CA Certificate: [(None)] Inner Authentication: [some letters] User Name: [] Password: [] I put there my user name and password and do not change default value and leave "Anonymous Identity"blank. As a result of that I get "Authentication required by wireless network". How can I solve this problem? I think it is important to notice that our system administrator tried to find some files (which are probably needed to be used as "CA Certificate"). He said that he does not know where this file is located on Ubuntu (he support only Windows). So, probably this is direction I need to go. I need to find this file. But may be I am wrong. May be something else needs to be done. Could you pleas help me with that?

  Read the article

• apache2 server running ruby on rails application has go daddy cert that works in chrome/firefox and ie 9 but not ie 8

  - by ryan

  I have a rails application up on a linode ubuntu 11 server, running apache2. I have a cert purchased from godaddy, (where we also bought our domain) and the cert is installed on my server. Part of my virtual host file: ServerName my_site.com ServerAlias www.my_site.com SSLEngine On SSLCertificateFile /path/my_site.com.crt SSLCertificateKeyFile /path/my_site.com.key SSLCertificateChainFile /path/gd_bundle.crt The cert works fine in Chrome, FireFox and IE 9+ but in IE 8- I get this error: There is a problem with this website's security certificate. The security certificate presented by this website was issued for a different website's address. I'm hosting multiple rails apps on this same server (4 right now plus some old php sites that don't need ssl). I have tried googling every possible combination of the error/situation that I could think of but at this point I'm shooting in the dark. The closest I could come up with is that some versions if IE don't support SNI. But that doesn't apply here because I am getting the warning on windows 7 machines running IE 8, and the SNI only seemed to apply to IE 8 if the operating system was windows XP. So why is this cert being accepted by all browsers but giving me a warning in IE 8? Edit: So doing a little more digging and I figured out some more. It turns out this is effecting IE 9 as well. However the problem seems to be that IE is not traversing the ssl chain to get to the right cert. FireFox and Chrome when I go to view certificate show the correct one, but IE is showing one of our other sites certificates. REAL QUESTION HERE: That being the case why is IE not getting the right certificate when others are and how do I fix it?

  Read the article

• Is the APC BR700G UPS (or similar) compatible with Active PFC power supplies?

  - by David Zaslavsky

  I'm looking at getting a UPS for my home computer. So far the APC BR700G looks very promising, except for one thing: one of the reviews on Newegg says that this UPS does not work with a power supply with Active PFC. Pros: Unit looks great, built well, very heavy, was excited to use it. Cons: Didn't research enough - many newer power supplies like my corsair 750w (and yes dells and other mainstreamers sell them too) that I bought last year have a feature called active pfc (power factor corrected). The signal for this backup battery doesn't fully support that feature and can cause issues. You can find an article on APCs site if you search their user forums for PFC. And the power supply in my computer is, in fact, an Active PFC PSU. I've already found one answer on this site claiming that it's not an issue, that "most quality supplies these days have PFC and work just fine with a UPS." That disagrees with the review on Newegg. Can someone explain this discrepancy? Also, what is it exactly about a UPS that makes it incompatible with an Active PFC PSU? (if anything) Is there some way to tell based on the technical specifications, or do I just have to hunt for reviews online to avoid wasting my money? While any input would be appreciated, I would prefer to get an answer from someone with actual experience with similar UPS's and Active PFC power supplies, who can tell me whether it works or not.

  Read the article

• What kernel modules are required for wi-fi to work?

  - by Leonid Shevtsov

  My custom-built 2.6.32 kernel cannot connect to any WPA-protected network. The kernel includes (probably?) everything that should be needed for wifi, including IPv4 network support (IPv6 is disabled), the ath5k wireless driver (which is used in the generic Ubuntu 2.6.31 kernel) and all crypto APIs. The card is being detected, however, iwlist scan returns wlan0 Failed to read scan data : Network is down and network-manager log says <info> (wlan0): driver supports SSID scans (scan_capa 0x01). <info> (wlan0): new 802.11 WiFi device (driver: 'ath5k') <info> (wlan0): exported as /org/freedesktop/NetworkManager/Devices/1 <info> (wlan0): now managed <info> (wlan0): device state change: 1 -> 2 (reason 2) <info> (wlan0): bringing up device. <info> (wlan0): preparing device. <info> (wlan0): deactivating device (reason: 2). supplicant_interface_acquire: assertion `mgr_state == NM_SUPPLICANT_MANAGER_STATE_IDLE' failed <info> modem-manager is now available <WARN> default_adapter_cb(): bluez error getting default adapter: The name org.bluez was not provided by any .service files <info> Trying to start the supplicant... <info> (wlan0): supplicant manager state: down -> idle <info> (wlan0): device state change: 2 -> 3 (reason 0) <WARN> nm_supplicant_interface_add_cb(): Unexpected supplicant error getting interface: wpa_supplicant couldn't grab this interface. The exact same configuration works with the generic kernel. Is anything except wifi and crypto api needed for wi-fi to work?

  Read the article

• Resolving loss of internet bandwidth in home network

  - by Caspar

  Recently, I've decided to connect my laptop at home to my modem/router through Ethernet cables built into my apartment. As these built-in Ethernet cables are usable via plugs built into the walls (called powerline adapters), I use some additional cabling (STP CAT6 cables) from my laptop/router to the plugs. In addition, I don't know any technical details about these built-in cables (as they're not visible), only the maximal bandwidth (1 GBit = Cat6?) that they're supporting. The built-in cables are Cat. 5e Ethernet cables. The problem is now that when I set up the connection, I cannot use the full bandwidth that my internet connection is actually offering (100 Mbit/s), only about 85 Mbit/s between 85 - 88 Mbit/s, despite the fact that all cables involved should support the maximal bandwidth. I know from other tests with one of the Ethernet cables in use that I can use almost 99 Mbit/s when I connect my laptop directly to the router/modem using only this one cable. In addition, it is very unlikely that the length of the resulting cable connection from my laptop to my router involving the built-in cables exceeds 100 m. So, what possible reasons for this loss of bandwidth exist? And how I can fix this issue? I hope this might help resolve the issue: The built-in cables appear to be Cat. 5e Ethernet cables. So, is there any problem when I connect Cat6 Ethernet cables directly to Cat5e Ethernet cables via the plugs?

  Read the article

• Windows Action Center notification icon says Backup in Progress when no backup is occurring

  - by allquixotic

  How can I get Windows Action Center's little flag in the notification area to stop saying "Backup In Progress" on Windows 8? It's driving me nuts. I disabled the Windows Backup service completely and turned off File Recovery. Nothing that I can tell is using any disk I/O whatsoever, by examining Task Manager's resource monitor. It's just a visual cue that seems totally wrong considering my disk is only using about 50 KB/s of sporadic writes for superfetch etc. This wouldn't be a problem for me, since I rely on the knowledge that the Backup service is disabled and there's no disk activity, but I am trying to support a more traditional user who relies on visual cues from the operating system and trusts them over low-level observations like "...but the Windows Backup service is disabled!" Therefore this user still thinks that the backup is going on, even after the service is disabled. Technically, I think this is a bug in Windows 8. It really should not be displaying "Backup in Progress" if ... you know ... a backup, is not, in progress. Which it isn't. Is there a workaround?

  Read the article

• SVN, Samba and Symbolic Links. How to get them all to play together?

  - by Camsoft

  I've got a website project under version control that relies on files from an unversioned directory on the same server via Symbolic Links. I'm currently storing the symbolic links in the repository. The idea is that if someone checks out a working copy on to the same server they can edit and test the working copy of the project before committing it back to the repository. When they checkout their working copy it successfully sets up the symlinks so that the entire site works when testing. The users that work on the project are Windows users, so I've set a samba shares on the server and then mapped them to network drives in Windows. People can edit their working copies directly on the server via network shares and then test them in the web browser before committing their changes back to the repository via TortoiseSVN. The Problem The problem I have is that Samba resolves the symlinks as expected but when a user tries to commit their changes back to the repository, TortoiseSVN thinks the linked files are part of the project and tries to commit the target files to the repository and not the symlinks themselves. I tried turning off symlink support in samba which means that the linked files cannot be resolved as I don't really want people to have access to the linked files nor do I want to import the linked files in the repository. The problem with this is that I get Can't stat '\webserver\projects\working\project\symlinked_file.php'. Access is denied Apart from the symlink problem everything else works 100% perfectly. Users can either checkout website projects to their machine and work on them (but can't test) or checkout them out to their space on the dev web server and work on them and fully test. So I don't want to change the workflow process, I just need a solution to the symbolic link issue. Many thanks. Originally posted on StackOverflow: http://stackoverflow.com/questions/2400917/svn-samba-and-symbolic-links-how-to-get-them-all-to-play-together

  Read the article

• Can't mv files between directories on vsftpd

  - by frankyue

  I enabled this in vsftpd.conf chroot_local_user=YES chroot_list_enable=YES chroot_list_file=/etc/vsftpd.chroot_list user_config_dir=/etc/vsftpd_user_conf and here is the user set in vsftpd_user_conf dirctory ftpupload : local_root=/mnt/upload But /mnt/upload is mounted from another directory /mnt/upload on /opt/upload type none (rw,bind) Here is the list in /mn/upload rough_images/ shoes-pentland/ vendor-upload/ shooting/ Additional, the shooting/ directory is mounted from another place /mnt/upload/shooting on /mnt/shooting none (rw,bind) Now here is the problem. When I use the ftp client to move the files between the directories but failed .Files can moved between any directories except the shooting one. The permission is right . I can move any files between this directories successful by using su ftpupload. It means the vsftpd didn't support the mount bind? Here is the vsftpd.conf listen=YES anonymous_enable=NO local_enable=YES write_enable=YES local_umask=000 dirmessage_enable=YES use_localtime=YES xferlog_enable=YES connect_from_port_20=YES chown_uploads=YES chown_username=app xferlog_std_format=NO log_ftp_protocol=YES chroot_local_user=YES chroot_list_enable=YES chroot_list_file=/etc/vsftpd.chroot_list user_config_dir=/etc/vsftpd_user_conf ls_recurse_enable=YES secure_chroot_dir=/var/run/vsftpd/empty pam_service_name=vsftpd pasv_enable=YES pasv_max_port=*** pasv_min_port=*** port_enable=YES pasv_address=*** virtual_use_local_privs=YES tcp_wrappers=YES and here is the mtab: /mnt/upload /opt/upload none rw,bind 0 0 /mnt/upload/shooting /mnt/shooting none rw,bind 0 0 all of the permissions under the /mnt/upload are the same: drwxrwxrwx * ftpupload app

  Read the article

• Windows is very slow with my new SSD

  - by Maksym H.

  I have a laptop HP probook 4520s with Core i5 M480 @ 2.67Ghz, 4Gb RAM, 640 GB HDD Radeon HD 6370m 1GB video card. It would seem like a good stack for work, right? But My HDD has crashed after everyday walking with laptop about 1 year. After buying my new SSD (Patriot memory - Torqx II 128 Gb SATA II) and installing new Windows 8 from scratch - it was amazing fast. But I had only install windows updates, and I feel that the speed become the same as my old HDD, after install other software for my work, it becomes so slow, so when I use my PC with old lower configuration and it really works better than my awesome laptop... I checked that TRIM and AHCI mode are turned on. So why's that? I asked for help in Patriot Memory support, they suggested to send them ATTO test results, done, sent. Here is the response: "Thank you very much for the attached results. Looking at the results, I can see that your SSD speed is a lot lower than it should be. Can you tell me your system specs?" Until they checked my email, I re-installed Windows 8 to Windows 7 and it was again perfect, but the story repeats it becomes slower and slower after every installing new software. Check out some screenshots.. (sorry for the screenshot with russian TaskManager, I hope you will recognize those parameters accordingly with your english or other lang TaskManager) So the main issue that something everytime loads the disc on 100% and the response time is jumping around 1000-3000 ms. Why am I asking about Windows? Because I tried to install Linux Mint (x86) and It just flies. So great performance independent on how many programs I have installed. Only Windows (any 7 or 8) has this problem. So guys, I appreciate any ideas about how to fix that and may be answers of main question - "why is it so.?" Thanks!

  Read the article

• Microsoft Access: computer freezes when user tries to update record

  - by CarlF

  A colleague and I have developed an Access 2003 database which is used throughout our department. Currently about four dozen people do data entry using one of two very similar forms. If 47 of us use them, they work perfectly. If Mr. 48 clicks the "Save" button, Windows XP freezes and a hard reset is needed. The problem has to be on his specific computer (Dell latitude D630) and not in the code because this problem only affects him. Complicating the matter: I don't work for IS, and this project is not supported by IS. If I'm going to get our tech support to fix the problem I had better be able to explain exactly what to do and how to do it, because they aren't going to invest any resources. I don't even have admin rights on the computer (and neither does its regular user). I've asked him to bring his laptop the next time he visits my building. (Just to make matters worse, he doesn't usually work in the same location as me or the other developer.) Any suggestions on debugging the problem? My first try will be to uninstall and reinstall Office, which I can do using corporate utilities without being admin. Note: yes, those are old versions of Office and Windows. We expect to upgrade later this year.

  Read the article

• Preferred mail system/server for a company?

  - by Trevoke

  Say you are responsible for setting up an email solution at a company. Which would be your choice? I know of the following options, but many of them not well: Gordano Mail System Exchange Exim Postfix Qmail Zimbra For having used it a little over two years, I really, really like Gordano Mail System. They offer a whole bunch of things, like calendaring, anti-spam, anti-virus, extremely complete and filterable logging options, aliases, a customizable webmail interface... And their software can be installed on both a Windows or Linux OS. In addition, their support is top-notch, their knowledgebase comprehensive (and, I will admit with a touch of pride, I have contributed, with my questions, to the addition of a few articles in there). Of course, they're not free, which can be a problem, but they're not Exchange, and they do offer pretty much everything that Exchange offers -- which is great if you want to stay away from that, but need all the features. Although, if you need a Blackberry Exchange Server, or something similar, I'm not sure what you should go for. So.. What would your choice be? Why? I've never played with a more DIY email solution, but I'm sure many people here have and wouldn't trade their setup for the world :)

  Read the article

• Why do hosts prefer Linux to Windows Server?

  - by iconiK

  So far I see a HUGE majority of hosts provide only Linux shared hosting, providing Windows only to VPS (or even to only dedicated servers). Why is it so? While Windows is a lot more expensive than Linux (though it depends on a lot of factors, not just initial and support license cost), it also provides ASP.NET, IIS and of course, Microsoft SQL Server. I know in the past it might have been because of cPanel being Linux only but now they have a Windows version. But still, why is Linux predominantly used on shared hosting? PHP works on both systems. IIS can be (and probably is) faster. MySQL runs on both systems as well. cPanel has a Windows version. Python, Perl, Ruby, all run on Windows as well. You even have MS SQL Server Express, which I find more superior than MySQL in both speed and features. Access is there for low usage requirements, as is SQLite (which is so great for quick small stuff). And with PowerShell you have a good alternative to the Unix shell. EDIT: I am looking for common reasons, I realize each hosting company (and/or it's clients) may have different needs. This becomes very important when you get to VPS or Cloud which give you a full operating system to use.

  Read the article

• Netgear FVS336G: appropriate solution for today's small businesses?

  - by bwerks

  Hey all, I've been looking into a routers to facilitate a vpn solution for a small business. While the Netgear FVS336G looks good on paper, it appears to have some fairly crippling setbacks that drag down what appears to be some great hardware. First off, the unit has been around for a couple years now, perhaps before 64-bit operating systems were as common as they are now, and complaints are everywhere that claim that SSL or IPsec (or both) VPN connections will not work with 64-bit operating systems. However, most of these claims mention only Vista, which makes me think that these problems could have potentially been solved since then. Unfortunately though, Netgear's support forums seem to be incredibly private, and policed by some troll named jmizuguchi who just closes down public posts in order to marshal them into the private ones. Danger, will robinson. Apparently their firmware upgrade process is a nightmare too, but that's beside the point. My question is this: has anyone configured one a Netgear FVS336G to operate in a server 2008 (or R2)/windows 7 64-bit network? If so, is it possible to use the microsoft vpn client or are third party clients still required? If this thing has just failed the test of time, is there a feature-comparable unit that I've missed, at anywhere near the same price range? Thanks!

  Read the article

• SSH attack CentOS Amazon EC2

  - by user37143

  Hi, I run a few Rightscale CentOS AMI based instances on Amazon EC2. Two months back I found that our SSHD security is compromised( I had added host.allow and host.deny for ssh). So I created new instances and done an IP based ssh that allows only our IPs through AWS Firewall(ec2-authorize) and chnaged the ssh 22 default port to some other port but two days back I found I was not able to login to the server and when I tried on 22 port the ssh got connected and I found that sshd_conf was changed and when I tried to edit sshd_config I found root had no write permission on the file. So I tried a chmod and it said access denied for 'root' user. This is very strange. I checked secure log and history and found nothing informative. I have PHP, Ruby On Rails, Java, Wordpress apps running on these server. This time I did a chkrootkit scan and found nothing. I renamed the /etc/ssh folder and reinstalled openssh through yum. I had faced this on 3 instances on CentOS(5.2, 5.4) I have instances on Debian as well those working fine. Is this a CentOS/Rightscale issue. Guys, what security measures I should take to prevent this. Please support me this is very critical. Thanks

  Read the article

• How do I change the Dropbox directory on a headless GNU/Linux server?

  - by DrTwox

  I have installed Dropbox 2.0.0 via command line on my home server (Ubuntu Server 12.04) to use for off-site automated backups, but I can't change the directory that the Dropbox daemon keeps synced. I've tried the following: The official docs say to use the desktop application, which is not applicable in my situation. However I installed the desktop app on my desktop machine and changed the default folder location, but I can't find where this change is stored in the ~/.dropbox/ directory so I can make the same change on the server. This page (and several others) recommends a Python script to do the job. Looking at the script, it opens a SQLite database called ~/.dropbox/dropbox.db, which does not exist on my Dropbox install, leading me to believe the script is out-of-date. This forum thread suggests manually inserting the required row in the config.db database, which I did, but it made no difference. I checked the same database file on my desktop machine, and it does not have the dropbox_path key, so I'm presuming the information in that thread is also out of date for version 2.0. I have tried to launch the Dropbox GUI configuration wizard over SSH with X11 forwarding, as suggested in one of the answers, but the binary must detect the absence of a local X11 install and it starts a command line daemon instead, which provides no means to change the option I need. I am currently using a symlink, as suggested as an answer, but this is a kludge. I would like to know the correct way to make the change. How do I change the Dropbox directory on a headless GNU/Linux server? Update: I've ditched Dropbox and started using Copy. Their Linux tools and support is far superior to Dropbox. I leave this question here in case someone, someday, can answer it.

  Read the article

• How to replicate a windows servers (IIS,Files,ConfigurationState)?

  - by Geo

  Maybe a better question is: What is the closest competitor for DoubleTake? I am looking to replicate a windows production server in case it fails have a immediate backup. Any idead? NOTE 1: I forget to add that this server is on the EC2 Amazon Cloud. NOTE 2: The main situation we have is recreating the configuration settings like IIS, FTP Server, SQL Server, SVN Server. NOTE 3: So far I have been giving three options as answers for my original question: AppAssurance -- After talking to their sales team they do not support Amazon as cloud provider. Basically there is a technical need to be able to reboot from a disk or similar media. So ESX Virtual machine environment will work, but not the EC2. Acronis -- which works as a backup in ghost style. This will work for other type of scenarios. Use the Amazon EC2 API -- This option is ideal, but only works if you are developing a cloud application rather than hosting a regular application in a cloud scenario. This means that I am still looking for the answer. Any other ideas.

  Read the article

• postfix not sending domain mail to mx

  - by orlandoresorts

  I'm trying to get postfix to forward email to my domain which is hosted by gmail. As I don't have any users on my server nor do I want to. Here's how I have things set up.. LEt's say you and I have a domain called mcdonalds.com the registrar has mcdonalds.com MX records pointing to gmail. (everything works for like a year) Now we set up a server to host a website. Then we create a mail account called [email protected] and send mail locally from the server using roundcube. This works. We can send mail to cnn.com we can send mail to serverfault.com we can email any/everyone. BUT we cannot send mail to our own domain mcdonalds.com So I cannot email [email protected] I cannot email [email protected] I cannot email [email protected] It gives the error: SMTP Error (450): Failed to add recipient "[email protected]" (4.1.1 : Recipient address rejected: User unknown in virtual mailbox table). I'm guessing because it is looking at the local server to find the mailbox and it doesn't exist. So how to I tell the server for any mail going to mcdonalds.com for [email protected] to send to my external mail server and NOT to lookup on the local www box we set up with zpanel. Any ideas?

  Read the article

• Delay init from starting a service for a period of time?

  - by Matthew

  I am trying to get a rudimentary NFS server up and running. Right now the server is configured as an NFS server due to a workaround for a vendor issue not supporting direct attached clustered storage, which we are trying to get them to resolve. The vendor software is Splunk. The splunk feature we are using requires files be located on shared storage (which for us is /mnt/nfs until they support a real clustered filesystem). Currently the server has a GFS2 filesystem mounted at bootup (it is the only server with the filesystem actively mounted so there should be no problems with locking). We went with GFS2 so switching over to a clustered filesystem is easy should the vendor begin supporting it. NFS is configured to mount that filesystem at /mnt/nfs, which the splunk installation than sees. Splunk is configured to find it's configuration files in /mnt/nfs. However, I am running into a problem where the splunk daemon starts before nfs is finished loading, and because it sees nothing at /mnt/nfs it starts creating files there, and then when the files disappear (nfs finishes mounting the share), splunk craps out. Splunk is set to run at runlevel 3, S90. NFS is set at runlevels 2-5, S60. Is there any way to delay the startup of the splunk process further?

  Read the article

• How can I preview the contents of books sold on Amazon in Internet Explorer 10?

  - by Aceman

  I run 64-bit Windows 7 and have both Internet Explorer 10 and a newly-downloaded copy of Google Chrome. I downloaded the latter when I found that I could not look (preview) the contents of books sold on Amazon (using it "Look Inside" feature) and wanted to try to get a handle on how extensive the problem was (i.e., whether it occurred on other browsers, too). It turns out that this isn't a problem with Chrome. However, I have grown accustomed over the years to IE and would prefer to resolve this problem instead. Here's an example of my attempt to 'Search Inside' a book on sale at Amazon: http://www.amazon.com/Intellectuals-Race-Thomas-Sowell/dp/0465058728/ref=sr_1_1?s=books&ie=UTF8&qid=1382301764&sr=1-1&keywords=thomas+sowell#reader_0465058728 I understand that I can't (as is the case in some technical support websites) add a screen shot (ie. JPG to this), but if I were to describe what this looks like in IE, the area where the text would appear appears as a blank white page with horizontal lines where the text would ordinarily be. I have just examined this posting of mine via Chrome and the contents of the selected page are clearly visible.

  Read the article

• Mailman delivery troubles

  - by stanigator

  I have apparently posted at the wrong place (superuser.com) for this question, so I'll just repost it here. Hope those of you who read both sites are not going to be offended. It's about mailing list management software called Mailman from GNU. Here are the details: Hosting provider: Vlexofree Domain: www.sysil.com with Google Apps Mailing List created from hosting cpanel: [email protected] I have registered a list of subscribers, and tried sending an email to [email protected]. I got the following error message: Delivery to the following recipient failed permanently: [email protected] Technical details of permanent failure: Google tried to deliver your message, but it was rejected by the recipient domain. We recommend contacting the other email provider for further information about the cause of this error. The error that the other server returned was: 550 550-5.1.1 The email account that you tried to reach does not exist. Please try 550-5.1.1 double-checking the recipient's email address for typos or 550-5.1.1 unnecessary spaces. Learn more at 550 5.1.1 http://mail.google.com/support/bin/answer.py?answer=6596 23si6479194ewy.44 (state 14). ----- Original message ----- MIME-Version: 1.0 Received: by 10.216.90.136 with SMTP id e8mr1469147wef.110.1264220118960; Fri, 22 Jan 2010 20:15:18 -0800 (PST) Date: Fri, 22 Jan 2010 20:15:18 -0800 Message-ID: <[email protected]> Subject: From: Stanley Lee <[email protected]> To: [email protected] Content-Type: multipart/alternative; boundary=0016e6dab0931bccc3047dcd2f1e - Show quoted text - Is there any way of fixing this problem? I would like to be able to have this mailing list to work through my hosting and domain. Thanks in advance.

  Read the article

• Should I use "Raid 5 + spare" or "Raid 6"?

  - by Trevor Boyd Smith

  What is "Raid 5 + Spare" (excerpt from User Manual, Sect 4.17.2, P.54): RAID5+Spare: RAID 5+Spare is a RAID 5 array in which one disk is used as spare to rebuild the system as soon as a disk fails (Fig. 79). At least four disks are required. If one physical disk fails, the data remains available because it is read from the parity blocks. Data from a failed disk is rebuilt onto the hot spare disk. When a failed disk is replaced, the replacement becomes the new hot spare. No data is lost in the case of a single disk failure, but if a second disk fails before the system can rebuild data to the hot spare, all data in the array will be lost. What is "Raid 6" (excerpt from User Manual, Sect 4.17.2, P.54): RAID6: In RAID 6, data is striped across all disks (minimum of four) and a two parity blocks for each data block (p and q in Fig. 80) is written on the same stripe. If one physical disk fails, the data from the failed disk can be rebuilt onto a replacement disk. This Raid mode can support up to two disk failures with no data loss. RAID 6 provides for faster rebuilding of data from a failed disk. Both "Raid 5 + spare" and "Raid 6" are SO similar ... I can't tell the difference. When would "Raid 5 + Spare" be optimal? And when would "Raid 6" be optimal"? The manual dumbs down the different raid with 5 star ratings. "Raid 5 + Spare" only gets 4 stars but "Raid 6" gets 5 stars. If I were to blindly trust the manual I would conclude that "Raid 6" is always better. Is "Raid 6" always better?

  Read the article

< Previous Page | 587 588 589 590 591 592 593 594 595 596 597 598  | Next Page >