Search Results

Search found 18803 results on 753 pages for 'link to'.

Page 599/753 | < Previous Page | 595 596 597 598 599 600 601 602 603 604 605 606  | Next Page >

• Translating debian network configuration to gentoo

  - by thpetrus

  I just got rid off Debian on my VPS (OpenVZ) and installed Gentoo on it, however it is a plain Gentoo image without further configuration, i.e. no working network. I'm not familiar with Debian and coulnd't figure out how to get the network set up, these are the debian network files /etc/network/interfaces: auto venet0 iface venet0 inet manual up ifconfig venet0 up up ifconfig venet0 127.0.0.2 up route add default dev venet0 down route del default dev venet0 down ifconfig venet0 down iface venet0 inet6 manual up ifconfig venet0 add ipv6addr/128 down ifconfig venet0 del ipv6addr/128 up route -A inet6 add default dev venet0 down route -A inet6 del default dev venet0 auto venet0:0 iface venet0:0 inet static address external_ip netmask 255.255.255.255 auto venet0:1 iface venet0:1 inet static address internal_ip netmask 255.255.255.255 Please note that external_ip, internal_ip and ipv6addr are placeholders. I copied the /etc/resolv.conf, know the gateway_ip and also have another ouput of ifconfig, if necessary. This is what I came up with, /etc/conf.d/net: config_venet0="127.0.0.2 netmask 255.255.255.255 brd 0.0.0.0" config_venet0:0="external_ip netmask 255.255.255.255 brd 0.0.0.0" route_venet0:0="default via gateway_ip" config_venet0:1="internal_ip netmask 255.255.255.255 brd 0.0.0.0" Broadcast IP is taken from ifconfig debian output - however it doesn't work. A symbolic link net.venet0:0 -> net.lo in /etc/init.d/ was created and I added net.venet0:0 to the boot runlevel.

  Read the article

• What is the best way to connect 3 switches with a router?

  - by Carlos Morales

  Hello everyone, I'm trying to rebuild the network from my work and I was thinking what is the best way to connect three switches and a router. The router has 4 ports so I thought to connect 2 switches to the router (each switch connected with 2 cables to the router) and then connect the third switch to one of the others with two cables. So is like this, two cables from switch one to the router, two cables from switch two to the router and two cables from switch 3 to switch 1 or 2. So my questions are: Is it better to connect the router to each switch with a cable or the more cables you have the better? If I connect the switch 3 to switch 1 or 2 is it better to connect it with a cable or you get better performance with more cables. If I'm wrong and there is a better or more efficient way to connect them please let me know. The router is a Netgear RP114 (I'll upgrade it to a Sonicwall NSA 240), switch 1 is a Netgear GS748T, switch 2 is a Cisco Catalyst 2924-XL and switch 3 is a D-link DGS-1024D Thank you very much

  Read the article

• Is VGA port hot-pluggable?

  - by Martin Bøgelund

  In meetings, I often see people detaching the VGA connector from one running laptop and connecting it to another, while the projector is still on. Is this 100% risk free, and OK by design of the VGA standard? If there's a risk involved in hot-plugging VGA, can it be removed by turning off or suspending either laptop, display, or both? I see this being done all the time without causing disaster, so clearly I'm not interested in answers stating "we do it all the time, so it should be OK!". I want to know if there's a risk - real or in theory - that something breaks when doing this. EDIT: I did an internet search on the topic, and I never found a clear statement as to why it is safe or unsafe to hot swap VGA devices. The typical form is a forum question asking basically the same question as I did, and the following types of statements Yes it's hot swappable! I do it all the time! It involves some kind of risk, so don't do it! You're some kind of moron if you think there's a risk, so just do it! But no explanation as to why it safe or not... Joe Taylors answer below contains a link to a forum post and answers that basically give me the same statements as mentioned above. But again, no good explanation why. So I looked for an actual manual for a projector, and found "Lenovo C500 Projector User’s Guide". It states on page 3-1: Connecting devices Computers and video devices can be connected to the projector at the same time. Check the user’s manual of the connecting device to confirm that it has the appropriate output connector. [image] Attention: As a safety precaution, disconnect all power to the projector and devices before making connections. But again, no good explanation.

  Read the article

• Show full URI/URL in Chrome's developer tools Network tab

  - by Lev

  When using Chrome to debug, I find it incredibly difficult to be efficient due to the fact that I don't see how I can force the "Network" tab of the developer tools to show the full request URI. It will show the full URI if you hover the link and wait a second, but this is incredibly counterproductive. All of my AJAX requests are sent to ajax.php, and handled by using query string arguments, like: ajax.php?do=profile-set ajax.php?do=game-save ... etc. Since I use AJAX extensively, my network tab is filled with "ajax.php", but I have to manually hover each and every entry to find the request I am looking for. Surely there has got to be another way!? I am constantly fed up by something new in Firefox and immediately force myself back into Chrome, but it is always the developer tools in Chrome that keep me from using it for an extended period of time. Hopefully I can find out how to do this so I can continue using Chrome as my numero uno. I've provided a screen shot to show you where I mean:

  Read the article

• Connect linux server to VPN server via PPTP

  - by wowpatrick

  I'm trying to connect a Linux (Ubuntu 10.04 LST) server to a VPN server via the PPTP client to an VPN server. I configured the PPTP client as said in the documentation. The connection is correctly added as an interface, but somehow the connection dose not work. ping -I ppp0 google.com dose not return anything and traceroute -i ppp0 only shows the first hop, and then displays nothing. Any ideas of what is going wrong? Incorrect routing configuration? ifconfig output for the configured interface: ppp0 Link encap:Point-to-Point Protocol inet addr:xx.x.xxx.xxx P-t-P:10.0.0.1 Mask:255.255.255.255 UP POINTOPOINT RUNNING NOARP MULTICAST MTU:1496 Metric:1 RX packets:415 errors:0 dropped:0 overruns:0 frame:0 TX packets:468 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:3 RX bytes:31428 (31.4 KB) TX bytes:32394 (32.3 KB) route output Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface xx.x.x.1 * 255.255.255.255 UH 0 0 0 ppp0 xx.xxx.xxx.xx sp.ip 255.255.255.255 UGH 0 0 0 eth1 192.168.3.0 * 255.255.255.0 U 0 0 0 eth2 192.168.2.0 * 255.255.255.0 U 0 0 0 eth1 default sp.ip 0.0.0.0 UG 100 0 0 eth1

  Read the article

• Using NFS for scalable PHP/MySQL web application

  - by Jeroen Moons

  Here's the situation: I have a PHP/MySQL web application that accepts user uploads (pdf files). From these pdf files' pages a preview image is made on the fly and presented to the web app's users. Some pdfs might be on the large side, most will be under 50 MB but some extreme cases could be as large as a few hundred MB. A little waiting for the preview image for large pdf files is acceptable but no more than a minute let's say. Everything is running on one server for now, but soon the app will hit the server's limit on both storage and processing power. My idea to solve the problem: To deal with this situation I had the idea of having one or more pdf processing servers as needed, and one or more file storage servers. These two types of servers are mounted to the server on which the actual app runs using NFS. The app could then use GearMan to delegate pdf processing tasks to these processing servers. The processing server can mount the storage server and read the file stored there, process it and write its output to that server. The servers I'm talking about will be amazon ec2 instances. The web app returns a link to the resulting pdf preview image on the storage server that was used which can then be used on the front end to show the image to the user. My question: I have zero experience with apps that use multiple servers, is this idea viable or is there a better way to do it? Is an NFS setup fast and reliable enough for this situation?

  Read the article

• Win7 VM @ ESXi Server @ VMWorkstation (Win7) - ping works only from VM -> HostOS, not vice versa

  - by DK2000

  right now I'm toying around with VM Ware stuff and not having any pcs then my laptop I decided to run an ESXi Server inside of VWmware Workstation. I was just curios to see if the server would allow to setup and run a VM. And after some tweaking there it was, working like a charm. Okay not that fast but startin' the VM from vSphere and "opening a console" gave my direct access to that VM. Now I wanted to see if I could ping the host from the VM (VM Workstation Network is set to "host only"). And it worked, at least from the VM I could ping the ESXi server and the host. From the host I am able to ping the ESXi Server but I can't ping the VM! I asked myself anyway where the VM got its ip adress from. At the DCHPs IP there is at no machine after all. I even tried to use that DHCP adress for my Host and it didn't work out. You can see my settings from the screenshot here (it's pretty wide so just a link): http://yfrog.com/n4desktopfeop The only thing that got me thinking was when I once changed the ESXi's IP from 192.168.92.137 to 192.168.0.137. I still was able to connect to the ESXi server via its new IP but when I tried to run the VM console from vSphere I got an error after a while that said "couldnt connect to 192.168.92.137:903". So vSphere connects just through a port of the ESXi server to the VM?!? Could I setup a Linux VM to use it as a DHCP that I'd at least have control over the IPs that are given. Which lowest end linux could be used for this purpose?!? Thank you for your time! :)

  Read the article

• Does this exist: a standardized way of documenting a file-system structure

  - by eegg

  At work, I'm in charge of maintaining the organization of a whole lot of varied data on a standard file-system. Part of this is coming up with sensible classification (by similarity, need, read/write access, etc), but the bigger part is actually documenting it: what documents/files/media should go where, what should not be in this directory, "for something slightly different, see ../../other-dir", etc. At the moment, I've documented this using a plaintext file filing.txt in every directory I want to document. If someone is unsure what's meant to be in any directory, they read that file. This works alright, but it seems odd that I have this primitive custom solution to a problem that any maintainer of a non-trivial directory structure must experience. Every company I've known of, for example, has some kind of shared file-system where agreed terminology for categorization is important. In my experience, people just have to learn what's what by trial-and-error and experimentation. So allow me to propose a better solution, and hopefully you can tell me if it exists. Any directory on any filesystem can have a hidden plaintext file named .filing. Its contents are descriptive human language. It uses some markup like Markdown, with little more than bold, italic, and (relative) hyperlinks to other directories. Now a suitably-enabled file browser will check for a file named .filing whenever it displays a directory. If it exists, its contents are parsed and displayed in an unobtrusive pane near the directory-path widget. Any links therein can be clicked, and the user will be taken to the target directory of that link. I think that the effort of implementing such a standard would pay back many times over in usability gains. We would have, say, plugins for Nautilus, Konqueror, etc.. It could be used to display directory information in the standard file lists served by webservers. And so on. So, question: does such a thing exist? If not, why not? Do people think it's a worthwhile idea?

  Read the article

• Broken Python installation on CentOS 5.8

  - by Beckett

  I already searched for solution to my problem via Google and stackoverflow's search facility, but haven't found anything related specifically to it. Here's the problem: I needed python 2.7.3 on CentOS 5.8 machine which has only python 2.4.3 preinstalled. Also neither there's the suitable version in it's repositories nor I can upgrade installed version. That's why I decided to build python from source code. But I've made a mistake: instead of make altinstall I did make install thus changing default version of the current installation. It was before I found this article - How to install Python 2.7.3 on CentOS 6.2 . I guess 5.8 and 6.2 versions aren't different to the extent this article is inapplicable. After installation of new python version I installed pip, but once I tried to invoke it, I got "No module named pkg_resources" error. In order to solve this issue I installed setuptools from repository. But it had only led to another error: "Distribution Not Found". My final step was to follow the guide I posted the link to, but I was unable to perform last step: easy_install-2.7 virtualenv command threw "-bash: /usr/local/bin/easy_install-2.7: .: bad interpreter: Permission denied" error. Now when I try to invoke pip or pip-2.7 both commands raise the same error with different names of binaries after "-bash:". Is there any way to fix this problem, so I could install new python version (2.7.3) alongside with the preinstalled one (2.4.3) according to the guide? Any help will be appreciated. P.S.: yum is working fine, although it needs python to function, so I hope the damage I unknowingly caused isn't very severe. Also I'm not a native English speaker, so I apologize for possible occasional grammatical and/or spelling errors.

  Read the article

• Change Windows 7 Explorer's Details Pane limits

  - by Paul

  For some reason, MS decided to completely kill the status bar's functionality in Win7 (and maybe Vista, but I don't know for sure). I have tried all possible options such as Classic Shell and so on. Basically, the one thing I miss most is seeing at a glance the total size of my selected files. I know I can press Alt+Enter or whatever, but that's not the point. The point is that the so-called 'details' pane stops providing details if more than 15 files are selected! WTH? Cannot understand the reason behind such a stupid arbitrary limit, that doesn't seem to be user-configurable at all. Anyway, what I'm looking for is a way to change that limit, either via the registry or otherwise. If changing the limit isn't possible, would it be possible for some programming genius to create a very small optimized light-weight non resource-hungry (you get the idea!) program whose sole purpose will be to automatically click the "Show more details..." link in the details pane after every file selection? For bonus points, the program should wait for a second or two after file selection is complete to do this, so that selecting multiple files in quick succession doesn't hit the HDD repeatedly. Any takers for the challenge? :)

  Read the article

• Custom Extensions on Managed Chromebooks

  - by user417669

  I am a developer looking for the best way to set up different schools with their own custom, private extensions (ie School A should be the only one with access to Extension A). Theoretically, I am aware that there are a few ways to get a custom, private extension pushed out on a domain: Host the .crx on a server and click "Specify a Custom App" in the management console. Create a Domain App by uploading a zip to the Chrome Web Store Upload the extension from my developer account to the Chrome Web Store and publish to a single "trusted tester," or make it unlisted Option (1), hosting the .crx, has not been working. I am not sure why, but the extension is simply not pushing out. I link directly to the crx file, which has the right ID and MIME type, still, no dice. If anyone has any tips or suggestions for getting this to work, I would love to hear them! Option (2), having the school create a domain app, seems a bit inefficient because it requires all schools to upload their own zip. So essentially I would have to email a zip file to the school, and have them publish it. All updates to the extension will also require a similar process, so this doesn't seem ideal. I doubt that option (3) would work. If I published to the admin as a "trusted tester", I don't think that the other people in the domain would be able to access it. If it is unlisted, I do not know how an admin could find it in the Chrome Web Store dialog. Also, I would rather avoid security through obscurity. Has anyone had success with hosting the extension and using the Specify a Custom App feature? Any other suggestions for getting a Custom Extension pushed out by the management console? Thanks so much!

  Read the article

• Radeon 6950 - Garbling of text and graphics in certain Windows only

  - by Greg

  This morning I noticed the text in Gmail (in Firefox 4) looked a little funny (kind of thin, maybe some color fringing). I went to work and thought it might be some ClearType issue or something with the way Direct way that FF4 draws to the screen. When I came back from work (I left the computer on), the problem was much worse - way beyond ClearType nit-picking. The text was barely readable. I opened Chrome and there was no such problem. It seems like only Windows that use hardware acceleration are garbled, and ones that use GDI are not. But, I fired up Dragon Age and didn't notice any problems (I only really looked at the main menu though). Here is a link to a screen shot that illustrates the problem. Notice how the Windows Live Mesh window is completely unreadable, the text in Firefox 4 (left) is pretty bad, while Chrome, the Windows Control Panel, and the task bar are perfectly fine. The fact that the problem shows up in screen shots and that it only happens in certain Windows makes me confident that the problem cannot be with the monitor or DVI cable. I am using the AMD Radeon drivers from 4/27/11. The card I have (MSI Frozr II) came with a slight overclock (810Mhz) out of the box, but it looks like when I'm on the Windows desktop it's not running at full clock (CCC reports 450Mhz). Still, I underclocked it to the stock reference clock (800Mhz) and it made no difference. The idle temperature according to Afterburner is 42-44 Celsius, which seems a tad high but not enough to cause a problem - it's cold to the touch if I open up the machine. What the heck could be causing this? The problem varies in intensity. As we speak I'm in Firefox and things look better than they did earlier - it'll probably get worse again soon. Radeon 6950 (MSI Frozr II), Seasonic X 560, Core i5 2500K at stock clockspeeds, 16GB RAM, Asus P8P67 M Pro

  Read the article

• Linux server: Dropped packets

  - by Lars

  I see dropped packets using ifconfig on my eth0 interface: eth0 Link encap:Ethernet HWaddr 00:15:17:0d:03:ca inet addr:10.0.1.2 Bcast:10.0.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:9000 Metric:1 RX packets:30268348 errors:0 dropped:70721 overruns:0 frame:0 TX packets:133076885 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:8699434077 (8.6 GB) TX bytes:194937313025 (194.9 GB) Interrupt:16 Memory:feae0000-feb00000 When i use ethtool -S i dont see anything wrong: NIC statistics: rx_packets: 30267138 tx_packets: 133074510 rx_bytes: 8699356158 tx_bytes: 194934147340 rx_broadcast: 35296 tx_broadcast: 5435 rx_multicast: 0 tx_multicast: 0 rx_errors: 0 tx_errors: 0 tx_dropped: 0 multicast: 0 collisions: 0 rx_length_errors: 0 rx_over_errors: 0 rx_crc_errors: 0 rx_frame_errors: 0 rx_no_buffer_count: 0 rx_missed_errors: 0 tx_aborted_errors: 0 tx_carrier_errors: 0 tx_fifo_errors: 0 tx_heartbeat_errors: 0 tx_window_errors: 0 tx_abort_late_coll: 0 tx_deferred_ok: 0 tx_single_coll_ok: 0 tx_multi_coll_ok: 0 tx_timeout_count: 0 tx_restart_queue: 0 rx_long_length_errors: 0 rx_short_length_errors: 0 rx_align_errors: 0 tx_tcp_seg_good: 5757001 tx_tcp_seg_failed: 0 rx_flow_control_xon: 8649 rx_flow_control_xoff: 62072 tx_flow_control_xon: 0 tx_flow_control_xoff: 0 rx_long_byte_count: 8699356158 rx_csum_offload_good: 30212111 rx_csum_offload_errors: 0 rx_header_split: 10857552 alloc_rx_buff_failed: 0 tx_smbus: 0 rx_smbus: 0 dropped_smbus: 0 rx_dma_failed: 0 tx_dma_failed: 0 I am running Ubuntu 12.04 with kernel 3.2.0-30-generic #48-Ubuntu SMP I have pinged every device on my internal network for about 24 hours, without packet loss. Also checked my router and my interface to the WAN, also no errors there. Does anyone have any clue?

  Read the article

• Errors generating gpg keypair

  - by Evan Lynch

  I posted this originally on stackoverflow, but was told that it was offtopic and this would be the better place to post it, so I am reposting it here and deleting my original topic. I have a rather old PGP key, but I've long ago lost the private key for it, so I'm trying to generate a new key with GPG on Windows 7. While it technically generates the key, GPA crashes every time I generate the keypair. I've tried this four times now and just downloaded what appears to be the latest version of Gpg4Win and am still receiving this problem. A comment on my original post informed me that GPA crashes is not a very good description of the problem, but unfortunately I can't do much better than that: all it tells me is "gpa.exe has crashed and will close now", I don't get an error dump or anything. Is there anything I can do to fix this, or is this just a bug in the latest version of Gpg4Win? Here are the specs of GPG that I'm using: GPA 0.9.4. GnuPG 2.0.22. My operating system is Windows 7 64 Bit, and I have 5 GB of RAM. Also, I was told to try generating the keypair on the command line but can't find any documentation for how to do this in Windows 7. If anyone could link me to current documentation for this, that would be a good workaround for solving this problem.

  Read the article

• MS Excel 2010 - Using DSN + 32 bit drivers

  - by Kristiaan

  I need some advice as im running into a problem and so far i have been unable to find a solution. We have a set of reports developed in MS Excel that use DSN file to connect to data sources to retrieve data, these work fine on 32 / 64bit systems, however we are moving to a terminal server environment using windows 2008 R2 64Bit. The reports fail to run using the DSN's within this environment if we only have the 32bit drivers installed and configured in the ODBC settings, the minute we install the 64Bit drivers the software works. Is there a way / Method of getting Excel or the DSN file to NOT use the 64Bit driver, but force it to use the 32bit driver. ANSWERED - But due to low user score i cannot "answer" my own question... Sadly there is no way to-do what i want to-do, without a lot of very nasty and not 100% perfect reg hacks. If you need to access 32bit ODBC data sources the application in question has to be 32Bit. here is a link to just one forum post i found relating to this type of problem, it appears the only way i would be able to accomplish this is to remove the 64bit version of office and install the 32bit version instead of it. http://social.msdn.microsoft.com/Forums/en-US/accessdev/thread/5108f337-f06a-4518-afe3-d3c1abd040ef/

  Read the article

• Pivot table not refreshing sort order

  - by William Anthony

  I have Pivot Table that get its data source from another sheet, same workbook. I want the sort order of data is same as the data source order, I choose "Sort in data source order" in Pivot Table option. The problem is, when I change the data order on data source worksheet, then I refresh the Pivot Table, the sort order didn't change. I googled that the Pivot Table should be unlink first then re-link again in order to work properly, so I tried the following: The original data source has named range: origdata. The fake data source has names range: dummydata I changed manually data source to dummydata then changed back to origdata. The sort order did change as expected. Now I want to make the operation automated, so I'm using this code in Worksheet.activate event. Note that, PT is PivotTable instance. ... PT.SourceData = "dummydata" PT.RefreshTable PT.SourceData = "origdata" PT.RefreshTable ... Change data source from VBA didn't change the sort order just like I did with manual method. Why is that? Am I missing something? Maybe there are some routine called when I changed the data source manually via toolbar button? Thanks in advance for your help.

  Read the article

• Website Use Monitoring for 3 People

  - by linkedlinked

  I work in an IT startup with 2 partners, and I'm the programmer/IT guy -- in other words, the work horse. To make a long story short, I'm doing most of the work right now, while they spend all day on Facebook. That's OK, because they're paying my salary, but if the project fails, I'm sure they'll blame me for it (I'm doing my best to make sure that doesn't happen!), and I want some sort of recourse. I already have an app that blocks time-wasters on my local PC, and keeps logs of when the app is enabled (so I can say "I had Facebook blocked from 9am-5pm today.") Is there any way I can get a brief summary of the most heavily visited sites, split up by client PC? At the end of the month, I want to be able to say "You both load Facebook, on average, every 10 minutes. You spend hours a day on Youtube, and haven't opened up our bugtracker in weeks" and maybe have a nifty chart or graph to match it. We have a crappy D-Link router, and no IT budget. They are both on Windows Vista, I run Ubuntu Linux. I don't want to install any monitoring software on their PC, but I'm totally fine with, say, routing all the network traffic through my machine. I guess I can think of lots of ways to accomplish this (telnet into JSSH and list open tabs? log all the DNS requests, per-domain? even thinking of setting up a webcam on my desk and just keeping 5-minute snapshots...), I just don't really know where to start. Any advice is appreciated, thanks!

  Read the article

• Google bots are severely affecting site performance

  - by Lynn

  I have an aggregate site on a linux server that pulls in feeds from a universe of about 2,000 blogs. It's in Wordpress 3.4.2 and I have a cron job that is staggered to run five times an hour on another server to pull in the stories and then publish them to the front page of this site. This is so I didn't put too much pressure all on one server. However, the Google bots, which visit a few times every hour bring the server to its knees in the morning and evenings when there is an increase in traffic on the site. The bots have something like 30,000 links to follow at this point. How do I throttle the bots to simply grab the new stories off the front page and stop there? EDIT- Details of my server configuration: The way we have this set up is the server that handles all the publishing is an unmanaged instance via AWS. It mounts the NFS server and connects to the RDS to update content, etc. You get to this publishing instance via a plugin that detects the wp-admin link and then redirects you into there. The front end app server also mounts the NFS and requests data from the RDS. It is the only one that has the WP Super Cache on it.... The OS is Ubuntu on the App server and the NFS runs CentOs. The front end is Nginx and the publishing server is Apache.

  Read the article

• vim coloring for git

  - by kelloti

  I'm on Windows and my vim loads with a terrible colorscheme with vim. The message is blue on black (so I can't see what I'm typing). I need to change the colorscheme, but :colorscheme slate doesn't do anything. :version vim - vi improved 7.3 (2010 aug 15, compiled oct 27 2010 17:51:38) ms-windows 32-bit console version included patches: 1-46 compiled by bram@kibaale big version without gui. features included (+) or not (-): +arabic +autocmd -balloon_eval -browse ++builtin_terms +byte_offset +cindent +clientserver +clipboard +cmdline_compl +cmdline_hist +cmdline_info +comments +conceal +cryptv +cscope +cursorbind +cursorshape +dialog_con +diff +digraphs -dnd -ebcdic +emacs_tags +eval +ex_extra +extra_search +farsi +file_in_path +find_in_path +float +folding -footer +gettext/dyn -hangul_input +iconv/dyn +insert_expand +jumplist +keymap +langmap +libcall +linebreak +lispindent +listcmds +localmap -lua +menu +mksession +modify_fname +mouse -mouseshape +multi_byte +multi_lang -mzscheme -netbeans_intg -osfiletype +path_extra -perl +persistent_undo -postscript +printer -profile -python -python3 +quickfix +reltime +rightleft -ruby +scrollbind +signs +smartindent -sniff +startuptime +statusline -sun_workshop +syntax +tag_binary +tag_old_static -tag_any_white -tcl -tgetent -termresponse +textobjects +title -toolbar +user_commands +vertsplit +virtualedit +visual +visualextra +viminfo +vreplace +wildignore +wildmenu +windows +writebackup -xfontset -xim -xterm_save -xpm_w32 system vimrc file: "$vim\vimrc" user vimrc file: "$home\_vimrc" 2nd user vimrc file: "$vim\_vimrc" user exrc file: "$home\_exrc" 2nd user exrc file: "$vim\_exrc" compilation: cl -c /w3 /nologo -i. -iproto -dhave_pathdef -dwin32 -dfeat_cscope -dwinver=0x0400 -d_win32_winnt=0x0400 /fo.\objc/ /ox /gl -dndebug /zl /mt -ddynamic_iconv -ddynamic_gettext -dfeat_big /fd.\objc/ /zi linking: link /release /nologo /subsystem:console /ltcg:status oldnames.lib kernel32.lib advapi32.lib shell32.lib gdi32.lib comdlg32.lib ole32.lib uuid.lib /machine:i386 /nodefaultlib libcmt.lib user32.lib /pdb:vim.pdb -debug My $HOME\_vimrc looks like colorscheme slate syn on set shiftwidth=2 set tabstop=2 and my $VIM\vimrc is the stock vimrc that comes with the Windows Vim distribution. How do I change my console Vim colorscheme? Especially for Git commits.

  Read the article

• Setting up port forwarding for web server

  - by reyjavikvi

  This could belong on Super User, but I thought this place was more appropiate. I want to run Apache in my computer and want to make it available to the outside world to test a couple things. Apparently, I have to go into my router's (a TP-LINK TD 8910G) settings and forward port 80 to my PC's IP. So far so good. Thing is, since the router uses a web based interface and it's kind of stupid, it told me that since I was using port 80 for this, I should access its settings through port 8080. Maybe it can't detect requests coming from the LAN, I don't know. Point is, now neither port can't access the configuration, and I can't access Internet. Specifically, trying to access anything (including 192.168.1.1, the router's settings) through port 80 turns up a blank page (maybe if I had the server running in my computer I'd get something, but I don't want to risk trying, I had to reset the router and restore the settings), and port 8080 gives a "Can't establish connection" error in Firefox (and similar ones in other browsers). Is there a way to configure the router to not redirect requests coming from inside the network? I'm a beginner with this stuff, so please try to explain in a simple way. If this is more appropiate in Super User, I'm sorry.

  Read the article

• Procurve Primary VLAN

  - by fukawi2

  I'm trying to depreciate usage of VLAN 1 on my ProCurve switches; 1 is unused. I understand that VLAN 1 must exist, but I want to remove it from all ports, especially trunks between switches. The problem I have is that stacking does not seem to work without VLAN 1. I have changed the primary VLAN and management VLAN on all the switches: (config)# primary-vlan 42 (config)# management-vlan 42 (config)# no vlan 1 untagged 25 Port 25 is the link between the 2 switches I'm testing with; the stack master and a member switch; I only want tagged traffic between the switches, no untagged frames. show stacking on the master shows all members as "UP" but I can not telnet any of them: Telnet failed: Connection timed out. All switches have manually assigned (static) IP addresses on VLAN 42, and all exist in the same /25 subnet, as does my desktop. I can telnet the switches directly from my desktop to the individual switch IP addresses, just not from the master switch. Do I need to reboot the switches to have the primary-vlan change take effect? Or is there something else I'm missing?

  Read the article

• How do I run multiple MVC apps within a subdomain on IIS7?

  - by Matthew Patrick Cashatt

  Hello and thanks for looking. Background I am currently wrapping up a development contract and the client would like for me to push a build of the application to their IIS 7-based server in which they would like to run multiple MVC apps. One of the issues I have off of the bat is that this server is already a subdomain on their larger network. So, if I enter SERVERNAME in my browser, it automatically directs to SERVERNAME.COMPANYNAME.COM. Now, this is just fine if I place my application in the default website/root. In this scenario, clicking a link that requests admin.html directs to `SERVERNAME.COMPANYNAME.COM/admin.html' as usual. BUT they want me to place the app in a subdomain on this server so that they can also run other apps on the same server. So I assume that I need MYAPP.SERVERNAME.COMPANYNAME.COM but I have no idea how to do that. Complicating matters is that my app and the future ones they wish to install are all MVC based which intercepts and re-writes URLs. I assume that this takes care of itself if I can just successfully get my app into a subdomain to begin with. What I have tried Creating a new site on the server in it's own app pool Setting the binding for that site to MYAPP.SERVERNAME.COMPANYNAME.COM Setting the binding for that site to MYAPP Setting the binding for that site to MYAPP.SERVERNAME Setting the binding for that site to MYAPP.SERVERNAME.COM Setting the binding for that site to MYAPP.COMPANYNAME.COM Nothing is working. Am I missing something simple here? Thanks, Matt

  Read the article

• How to enable hotlink protection without hardcoding my domain in the Apache config file?

  - by Jeff

  Been surfing around for a solution for a couple days now. How do I enable Apache hotlink protection without hardcoding my domain in the config file so I can port the code to my other domains without having to update the config file every time? This is what I have so far: RewriteCond %{HTTP_REFERER} !^$ RewriteCond %{HTTP_REFERER} !^http://www\.example\.com [NC] RewriteRule \.(gif|ico|jpe|jpeg|jpg|png)$ - [NC,F,L] ... And this is what Apache suggests: SetEnvIf Referer example\.com localreferer <FilesMatch \.(jpg|png|gif)$> Order deny,allow Deny from all Allow from env=localreferer </FilesMatch> ... both of which hardcode the domain in their rules. The closest I came to finding any info that covers this is right here on ServerFault, but the conclusion was that it cannot be done. Based on my research, that appears to be true, but I didn't find any questions or commentary dedicated soley to this question. If anyone's curious, here is the link to the Apache 2 docs that cover this topic. Note that Apache variables (e.g. %{HTTP_REFERER}) can only be used in the RewriteCond text-string and the RewriteRule substitution arguments.

  Read the article

• Network speed between a VM and another machine which is not residing on the same host, is 11MB/s at most

  - by Henno

  Problem Network speed between a VM and another machine which is not residing on the same host, is 11MB/s at most. Topology Facts ESXi5 version is 5.0.0.504890 VM has the latest Vmware Tools installed VM is using E1000 network driver Physical box has Win Srv 2008 R2 as the OS CrystalDiskMark says the drive on physical box can read/write 100MB/s vCenter is another vm on esx both vm and physical box are showing 1Gbps link speed Configuration Networking shows vmnic0 as 1000 Full NTttcp is a client/server tool from Microsoft for measuring pure network throughput Here's what I've done so far: Test1: VM is running Filezilla FTP Server (default settings, one user account made) Physical box is running Filezilla FTP Client (default settings) Physical box is uploading a big file to FTP server Transfer speed (as observed by Windows Task Manager on both machines): ~11MB/s (bad) Physical box is downloading that file from FTP server Transfer speed (as observed by Windows Task Manager on both machines): still ~11MB/s (bad) Could it be disk performance issue? Test2: Physical box is running ntttcpr.exe -a 6 -m 6,0,VM_IP_ADDRESS VM is running ntttcps.exe -a 6 -m 6,0,PHY_BOX_IP_ADDRESS Transfer speed (as observed by Windows Task Manager on both machines): ~11MB/s (bad) Could it be switch performance issue? Test3: physical box is running vSphere Client I open Summary Storage datastore Browse Datastore... from physical box and upload a file to datastore Transfer speed (as observed by Windows Task Manager on physical box): ~26-36MB/s (good) Could it be a vm specific issue? Test4: Installed ntttcp to another vm on the same esx server Measured network performance between vms on the same esx server with NTttcp Transfer speed (as observed by Windows Task Manager on physical box): ~90-120MB/s (excellent :) Test5: I have another esx server on the same site, connecting to the same datastore and same switch. Those two ESX servers have both 2 NICs. One NIC goes to switch while the other goes directly to the other ESX server. vMotioned one of the testing vms off to the other ESX host Measured network performance between vms on different esx servers with NTttcp Transfer speed (as observed by Windows Task Manager on physical box): ~11MB/s (bad) While I'm aware of these: ESXi 4.1 slow file transfer ESXi 5 network performance is slow Debian Etch and ESXi slow network speeds VMWare ESXi slow file copy to guest they did not help (or I must have been missed something)

  Read the article

• Windows 7 hangs after going into sleep a second time

  - by Brian Stephenson

  I've searched everywhere around Google and can't figure out why this is happening so I decide to ask here to see if anyone has a problem like this. Like it says in the title, whenever I sleep ONCE I'm able to wake the system, but going back to sleep again AFTER waking up for the first time results in it hanging on no input and no output, with the fan spinning as fast as possible and alot of heat being spewed out by the fan as well. I've tried various things like setting all USB Hub Root's to not get switched off for power saving, disabling USB selective suspend, disabling PCI-e link state power management, and even unplugging ALL USB devices and it wont wake up after the second attempt. And I've even waited up to a full hour of the CPU fan spinning loudly and it's still stuck trying to wake up. The only USB devices I use are a Microsoft USB Comfort Curve Keyboard 2000 (IntelliType Pro) and a generic HID compliant mouse from Creative model number OMC90S "CREATIVE MOUSE OPTICAL LITE". My other devices like external drives and controllers are unplugged when I'm not using them as having too many USB devices plugged in at a time causes a deadlock on almost all of the ports I have. Here's my system specifications (Most of these are from CPU-Z): Brand: Gateway DX4300-19 Mainboard: Gateway RS780 Chipset: AMD 780G Rev 00 Southbridge: AMD SB700 Rev 00 LPCIO: ITE IT8718 BIOS: American Megatrends Inc. ver P01-A4 09/15/2009 CPU: AMD Phenom II X4 810 at 2.60 GHz RAM: 8.0 GB DDR2 Dual Channel Ganged Mode at 400 MHz GPU: ATI Radeon HD3200 Graphics Intergrated - RS780 OS: Windows 7 Home Premium x64 OEM (Acer Group) HDD: WDC WD10EADS-22M2B0 1.0 TB (Western Digital Green Caviar) My BIOS has absolutely no control over how I setup the sleep mode to be either S1 or S3. So I can't check these settings or even change them. Hybrid sleep is also disabled, I can successfully go into hibernation and wake from hibernation but this is painfully slow due to a harddrive problem I'm having with this "Green Drive". (Hibernation takes over ~3 minutes to complete) Any help would be appreciated, thanks.

  Read the article

< Previous Page | 595 596 597 598 599 600 601 602 603 604 605 606  | Next Page >