Search Results

Search found 33720 results on 1349 pages for 'zend db table'.

Page 599/1349 | < Previous Page | 595 596 597 598 599 600 601 602 603 604 605 606  | Next Page >

• Build and migrated to software raid (mdadm) on GPT disk, now can't assemble array

  - by John H

  mdadm, gpt issues, unrecognized partitions. Simplified question: How do I get mdadm to recognize GPT partitions? I have been attempting to convert/copy my Ubuntu 11.10 OS from a single drive to software raid 1. I have done similar in the past, but in this case, I was adding in a drive that has been configured for GPT and I tried to work with that without fully looking into the implications. Currently, I have a non-booting mdadm RAID 1 array of /dev/md127 (the OS assigned that and it keeps picking up). I am booting off of live USB keys, currently System Rescue CD from sysresccd. While gdisk and parted can see all the partitions, most of the OS utilities do not, including mdadm. My main goal is just to make the raid array accessible so I can get pull the data and start fresh (without using GPT). /dev/md127 /dev/sda /dev/sda1 <- GPT type partition /dev/sda1 <- exists within the GPT part, member of md127 /dev/sda2 <- exists within the GPT part, empty /dev/sdb /dev/sdb1 <- GPT type partition /dev/sdb1 <- exists within the GPT part, member of md127 History: POINT A: The original OS was install on sda (actually /dev/sda6). I used a the Ubuntu live usb to add sdb. I got warning from fdisk about GPT so I used gdisk to create a raid partition (sdb1) and mdadm to create a raid1 mirror with a missing drive. I had many issues getting this working (including being unable to get grub to install) but I eventually got it to boot using grub on sda and /dev/md127 off of sdb. So at point A, I had copied my OS from sda6 to md127 on sdb. I then booted into a rescue mode and attempted to get a bootloader onto sdb, which failed. I then discovered my mistake: I had installed the raid onto sdb instead of sdb1, essentially overwriting the sdb1 partition. POINT B: I now had two copies of my data- one on md127/sdb, and one on sda. I destroyed data on sda and created a new GPT table on sda. I then created sda1 for the raid array, and sda2 for a scratch partition. I added sda1 into the raid array and let it rebuild. md127 now covered /dev/sdb and /dev/sda1 as fully active and synced. POINT C: I rebooted onto linux rescue again and was still able to access the raid array. I then removed /dev/sdb from the array and created /dev/sdb1 for the raid. I added sdb1 to the array and let it sync. I was able to mount and access /dev/md127 without issues. Once it completed, both /dev/sda1 and /dev/sdb1 were GPT partitions and actively syncing. POINT D (current): I rebooted again to test if the array would boot and grub failed to load. I booted off of my live thumb drive and found that I can no longer assemble the raid array. mdadm doesn't see the required partitions. -- root@freshdesk /root % uname -a Linux freshdesk 3.0.24-std251-amd64 #2 SMP Sat Mar 17 12:08:55 UTC 2012 x86_64 AMD Athlon(tm) II X4 645 Processor AuthenticAMD GNU/Linux === /proc/partitions and parted look good: root@freshdesk /root % cat /proc/partitions major minor #blocks name 7 0 301788 loop0 8 0 976762584 sda 8 1 732579840 sda1 8 2 244181703 sda2 8 16 732574584 sdb 8 17 732573543 sdb1 8 32 7876607 sdc 8 33 7873349 sdc1 (parted) print all Model: ATA ST31000528AS (scsi) Disk /dev/sda: 1000GB Sector size (logical/physical): 512B/512B Partition Table: gpt Number Start End Size File system Name Flags 1 1049kB 750GB 750GB ext4 2 750GB 1000GB 250GB Linux/Windows data Model: ATA SAMSUNG HD753LJ (scsi) Disk /dev/sdb: 750GB Sector size (logical/physical): 512B/512B Partition Table: gpt Number Start End Size File system Name Flags 1 1049kB 750GB 750GB ext4 Linux RAID raid Model: SanDisk SanDisk Cruzer (scsi) Disk /dev/sdc: 8066MB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 31.7kB 8062MB 8062MB primary fat32 boot, lba === # no sda2, and I double the sdb1 is the one shown in parted root@freshdesk /root % blkid /dev/loop0: TYPE="squashfs" /dev/sda1: UUID="75dd6c2d-f0a8-4302-9da4-792cc7d72355" TYPE="ext4" /dev/sdc1: LABEL="PENDRIVE" UUID="1102-3720" TYPE="vfat" /dev/sdb1: UUID="2dd89f15-65bb-ff88-e368-bf24bd0fce41" TYPE="linux_raid_member" root@freshdesk /root % mdadm -E /dev/sda1 mdadm: No md superblock detected on /dev/sda1. # this is probably a result of me attempting to force the array up, putting superblocks on the GPT partition root@freshdesk /root % mdadm -E /dev/sdb1 /dev/sdb1: Magic : a92b4efc Version : 0.90.00 UUID : 2dd89f15:65bbff88:e368bf24:bd0fce41 Creation Time : Fri Mar 30 19:25:30 2012 Raid Level : raid1 Used Dev Size : 732568320 (698.63 GiB 750.15 GB) Array Size : 732568320 (698.63 GiB 750.15 GB) Raid Devices : 2 Total Devices : 2 Preferred Minor : 127 Update Time : Sat Mar 31 12:39:38 2012 State : clean Active Devices : 1 Working Devices : 2 Failed Devices : 1 Spare Devices : 1 Checksum : a7d038b3 - correct Events : 20195 Number Major Minor RaidDevice State this 2 8 17 2 spare /dev/sdb1 0 0 8 1 0 active sync /dev/sda1 1 1 0 0 1 faulty removed 2 2 8 17 2 spare /dev/sdb1 === root@freshdesk /root % mdadm -A /dev/md127 /dev/sda1 /dev/sdb1 mdadm: no recogniseable superblock on /dev/sda1 mdadm: /dev/sda1 has no superblock - assembly aborted root@freshdesk /root % mdadm -A /dev/md127 /dev/sdb1 mdadm: cannot open device /dev/sdb1: Device or resource busy mdadm: /dev/sdb1 has no superblock - assembly aborted

  Read the article

• Safety of purchasing country-specific domains from registrars?

  - by Marc Bollinger

  None of the previous questions tackle some of the one-off (or further) countries' registries, beyond .co.uk, .it, et al. or else I'd have found an answer myself. Is it safe to buy a domain from a foreign country TLD from a registrar? http://www.iana.org/domains/root/db/ I'm just looking for information for a vanity domain, so obviously I'm alright without an answer, but it's an unasked question (or at least, unanswered), and I'm not exactly in a hurry to give my credit card information over country lines, sight unseen.

  Read the article

• Open Office Calc auto complete

  - by Christian

  Is there a way to tell Open Office Calc to use values from another table for it's auto complete feature?

  Read the article

• Can Excel sorts be saved and used again?

  - by Robert Kerr

  On an Excel 2007 worksheet, I have several tables, each sharing the same columns. For every table, I sort in several particular ways, depending on the task at hand. It gets tedious going to the Data tab, clicking Sort, unchecking the "my data has headers" checkbox, then add/removing the columns and ordering sort criteria. Is it possible to: * Save a given sort criteria (a named sort)? * Apply the sort against any selected range? * Create a button to execute each saved sort? In the end, I would create 4 or 5 named sorts and a button for each on the worksheet. Then would be able to select any range of rows, from any table, and click one of the sort buttons. The sort would execute.

  Read the article

• Intelligent Conflict Detection and Resolution

  - by Doug Reid

  0 false 18 pt 18 pt 0 0 false false false /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:12.0pt; font-family:"Times New Roman"; mso-ascii-font-family:Cambria; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Cambria; mso-hansi-theme-font:minor-latin;} Conflict Detection and Resolution in Oracle GoldenGate11gR2 has gone through a significant overhaul. The improvements that have been made to this area are substantial and will make it easier for customers to implement complex, heterogeneous GoldenGate configurations. GoldenGate has provided methods for conflict detection and resolution for a number of past releases, but at Oracle we have the opportunity to take advantage of some of the great ideas in this area. Oracle has had feature rich conflict detection and resolution framework in other products, which has been implemented in Oracle GoldenGate 11gR2. These improvements are geared toward helping customers more easily implement advanced configurations that require conflict detection and resolution by providing a robust framework for conflict detection for all DML statements and resolution via pre-built methods, all with less code and simpler syntax than in prior releases. Conflict Detection and Resolution in Oracle GoldenGate 11gR2 is available for our supported heterogeneous platforms, which includes Oracle Database, MySQL, Sybase ASE, SQL Server, and DB2 Linux, Unix, Windows, z/OS, plus DB2 on i Series, which is newly supported in this release. Additional information on the Conflict Detection and Resolution capabilities can be found in our documentation. 

  Read the article

• Too much I/O in the morning ?

  - by steveh99999

  Interesting little improvement on a SQL 2005 system I encountered recently….. Some background - this system had a fairly ‘traditional OLTP’ workload ie  heavily used during day – till around 9pm, then had a batch window for several hours, then not much activity in the early hours of the day, until normal workload resumed the following morning. Using perfmon, I noticed that every morning, we would see a big spike in SQL Server I/O when the application started to be used... As it was 2005 I decided to look at what tables were in cache before and after the overnight batch processing ran… ( using DMV equivalent of dbcc memusage that I posted earlier). Here’s what I saw :-     So, contents of data cache split fairly evenly between my 'important/heavily used' tables.   After this:- some application batch processing,backups, DBCC checks and reindexes were run.  A fairly standard batch I'd suggest. Cache contents then looked like this :- Hmmmm – most of cache is now being used by a table I’ve described as ‘unimportant’. Why ? Well, that table was the last to be reindexed…. purely due to luck, as  the reindexing stored procedure performing a loop in alphabetical order through all application tables...  When the application starts to be used again – all this ‘unimportant’ data has to be replaced in cache by data that is heavily used… So, we changed the overnight reindex scripts –  the most heavily accessed tables are now the last to be reindexed. Obvious really, but we did see a significant reduction in early-morning I/O after changing the order of our reindexing.  

  Read the article

• Partner OBI 11g 5-Day Hands-on Training Workshop

  - by Mike.Hallett(at)Oracle-BI&EPM

  Normal 0 false false false EN-GB X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0cm 5.4pt 0cm 5.4pt; mso-para-margin-top:0cm; mso-para-margin-right:0cm; mso-para-margin-bottom:10.0pt; mso-para-margin-left:0cm; line-height:115%; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi; mso-fareast-language:EN-US;} 14 - 18 January 2013, Oracle Reading (UK) REGISTER HERE NOW This 5 day hands-on workshop provides attendees a hands-on experience to practice with OBI11g environment. Participants will gain in-depth understanding of new architecture of OBIEE 11g, security mode, installation/configuration as well as reporting aspects like new ROLAP/MOLAP style hierarchical browsing, new chart types, Action Framework and Visualization. Please note that attendees are required to have a laptop.  This training is only for OPN member Partners. View here laptop requirements and detailed agenda.

  Read the article

• Internal hard drive, can't format

  - by user113923

  I cannot format anymore the hard drive of my laptop. Here is how I proceed: I am starting my computer with a USB live drive (Ubuntu 10.04 LTS - the Lucid Lynx). Then I start disk utility and try to format the hard drive - I choosed to format the Master boot record but I get the following error: Error creating partition table: helper exited with exit code 1: Error calling fsync(2) on /dev/sda: Input/output error If I try to delete partitions I get the following error Error erasing: helper exited with exit code 1: In part_del_partition: device_file=/dev/sda, offset=32256 Entering MS-DOS parser (offset=0, size=30005821440) MSDOS_MAGIC found looking at part 0 (offset 32256, size 4096157184, type 0x83) new part entry looking at part 1 (offset 10618836480, size 8414461440, type 0x83) new part entry looking at part 2 (offset 19033297920, size 1077511680, type 0x82) new part entry looking at part 3 (offset 20110809600, size 9895011840, type 0x07) new part entry Exiting MS-DOS parser MSDOS partition table detected got it got disk got partition - part-type=0 Error: Input/output error during write on /dev/sda ped_disk_commit_to_dev() failed If I try to install ubuntu frrom the usb on the hard drive and choose erase and use the entire disk I get the error message Input/output error during write on /dev/sda For side infos I have at the moment 4 partitions on my hard drive: /dev/sda1 (ext2) /dev/sda2 (ext2) /dev/sda3 (swap) /dev/sda1 (ntfs) + /dev/sda (unlocated Space) My ultimate goal is to reinstall ubuntu and have only 2 partitions... I would really appreciate any help here! Thanks JB

  Read the article

• Oracle Enterprise Manager 12c R3 introduces advancements in cloud lifecycle and operations management

  - by Anand Akela

  Oracle Enterprise Manager 12c Release 3 (R3) was announced ( Press Release ) earlier today. It is now available for download at  OTN . This latest release features improvements in several areas, including: Improvements to Private Cloud and Engineered Systems Management Expanded Middleware and Application Management Capabilities Efficiency Gains for Enterprise manager Users in EM’s Enterprise-Ready Framework You can learn more about what's new in the Oracle Enterprise Manager 12c R3 in the Enterprise Manager 12c documentation . You will see more blogs and details about the new features during the next few weeks. Please let us what On July 18th, you can join us at a webcast to hear Thomas Kurian, EVP of Product Development on what Oracle Engineering has achieved with Oracle Enterprise Manager 12c Release 3 to address these challenges. Later, during this webcast, Oracle experts will discuss the latest capabilities in Oracle Enterprise Manager 12c Release 3 for cloud lifecycle and operations management. The presentation will be followed by a live Q&A session with Oracle experts. You can also join us online on Twitter to get your specific questions answered. Please use hash tag #em12c to join the conversation. /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman","serif";} Register Now for the Webcast! Stay Connected: Twitter |  Face book |  You Tube |  Linked in |  Newsletter

  Read the article

• What are the different Partition Types listed in gparted?

  - by keithterrill

  I am reformatting an older 40meg drive using gparted from within a Linux distro. The drive had no partitions and no partition table, so I am creating a new Partition Table via the Advanced option. The default partition type is msdos, which I think is the same as MBR in parted. The description sounds right: maximum of 4 primary partitions, or 3 primary and 1 extended partition, maximum of 2 tb with 512b sectors. There are a number of other options, gpt being one. Which I would use if the drive was greater than 2 tb. The following partition types are also available: apx, amiga, bsd, dvh, mac, pc98, sun, loop. The question: what are these other types and where can I find a description or discussion about them? Secondary question: is there any reason to not use gpt on a smaller drive? Thank-you

  Read the article

• what would be a good way to implement/render a 2d tiled map for a browser game?

  - by jj_

  I've made this little rpg ruby game I did while learning and now I'd like to make it into a browser game. I've already set up Sinatra framework to serve it, so what I am looking for, before everything else, is a way to represent the game map in browser (location attributes are stored in db). A new map is randomly generated by code for each new game at each game start. For now forget db, and let's say a map (say 100x100 "squares") is stored as a tridimensional array. (x,y, ...) Last "dimension" of array stores who & what is at that map cell: a player, a building, whatever. So all I have to do is render those "squares" or array cells to a 2d tiled map in the browser. The map does not need to refresh or be dynamically fetched as you scroll it, (at least at this stage of development) but, a technology which would allow me to do so in future would be a good reason for choosing it. Things that I thought of: html tables, html5 canvas, some js framework which is designed exactly with this purpose (which I do not know of = please advice). Yes I know about gamequery-js framework, but I've never used it, and I don't know if it's going to slow down everything down to inusability as I'm adding new features (scrolling, ajax). I really don't know of any other alternatives.. maybe there are lighter approaches? Easier or more minimalistic ways ? More targeted js framework which is the right tool for the job? Maybe just some html canvas code, or even simple image maps, or images with absolute positioning will be enough? The thing is I'd like to start simple, and then gradually make it better, so, as I said before, I'd prefer something that will give me room for improvement or is headed toward new web tendencies but which will also give me a bit of gratification in the beginning :) So.. advices are needed! And appreciated! :) Thanks p.s. Flash is excluded because I don't like it.

  Read the article

• Go/Obj-C style interfaces with ability to extend compiled objects after initial release

  - by Skrylar

  I have a conceptual model for an object system which involves combining Go/Obj-C interfaces/protocols with being able to add virtual methods from any unit, not just the one which defines a class. The idea of this is to allow Ruby-ish open classes so you can take a minimalist approach to library development, and attach on small pieces of functionality as is actually needed by the whole program. Implementation of this involves a table of methods marked virtual in an RTTI table, which system functions are allowed to add to during module initialization. Upon typecasting an object to an interface, a Go-style lookup is done to create a vtable for that particular mapping and pass it off so you can have comparable performance to C/C++. In this case, methods may be added /afterwards/ which were not previously known and these new methods allow newer interfaces to be satisfied; while I like this idea because it seems like it would be very flexible (disregarding the potential for spaghetti code, which can happen with just about any model you use regardless). By wrapping the system calls for binding methods up in a set of clean C-compatible calls, one would also be able to integrate code with shared libraries and retain a decent amount of performance (Go does not do shared linking, and Objective-C does a dynamic lookup on each call.) Is there a valid use-case for this model that would make it worth the extra background plumbing? As much as this Dylan-style extensibility would be nice to have access to, I can't quite bring myself to a use case that would justify the overhead other than "it could make some kinds of code more extensible in future scenarios."

  Read the article

• Oracle Tutor: Document Audit and Maintenance

  - by Emily Chorba

  Normal 0 false false false EN-US X-NONE X-NONE MicrosoftInternetExplorer4 /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman","serif";} Perhaps the most critical phase in the process of documenting policies and procedure -- and the greatest challenge to owners -- is the maintenance of published documents. Documents must reflect current practice and they must be accurate. The most effective way to ensure this is through the regular audit of documents. In the Tutor environment, a Document Owner must audit each of his/her documents once every 6 to 12 months to verify that the document reflects actual practice. If it does not, the document is updated or employees are retrained (depending on the nature of the discrepancy). If a document update is required, the Tutor system enables the owner to modify and redistribute the document within one work day. This is possible because: Documents contain a minimum of detail, thereby reducing the edits. Document format and structure are simple, so changes are easy to identify The Tutor Author software tool enables the Document Owner or the Document Administrator to update the file quickly. The Document Administrator verifies the document format and integration, publishes the document, and distributes it to all affected employees, thereby freeing the Document Owner of the more tedious tasks. Learn More For more information about Tutor, visit Oracle.Com or the Tutor Blog. Post your questions at the Tutor Forum. Emily Chorba Principle Product Manager Oracle Tutor & UPK

  Read the article

• Confusion installing mongodb manually on ubuntu because sitting behing a proxy

  - by black sensei

  I am forced to install mongodb manually on an ubuntu server because the machive sits behind a proxy and there is no way to temporary open port 11371 for key exchange to happen. am following this official tutorial . so I downloaded the tgz and extracted it in /usr/local/bin/mongodb . where i got confused is when assigning the ownership of the /data/db to the user mongo Question 1 So who creates the user mongo ? Question 2 How to get control-scripts working? thanks

  Read the article

• Collapsing Bookmarks

  - by Tim Dexter

  I said I would tackle documenting some of the new features in the 10.1.3.4.1 roll up patch I mentioned last week. With the patch you can now set the default state of bookmarks (if you create them) in your PDF outputs. If your users prefer to see them all collapsed to the base level or may be collapsed to the second level to ease navigation; whatever they need. Its another opportunity for you to look like a star! You of course need to start with a table of contents; then add the convert|copy to bookmarks command. You can then add the new collapse command to set the appropriate level in the bookmarks. <?copy-to-bookmark:?> <?collapse-bookmark:show;2?> <<< Table of Contents >>> <?end convert-to-bookmark?> The command allows you to expand or collapse the bookmarks as you need. Of course you will know how many levels you will have in the final output document. The command takes the form: <?collapse-bookmark:show|hide;level int?> Some examples <?collapse-bookmark:hide;1?> <?collapse-bookmark:hide;2?> <?collapse-bookmark:hide;3?> Sample template and data here. Dont forget you need that 10.1.3.4.1 roll up!

  Read the article

• mysqld crashes on any statement

  - by ??iu

  I restarted my slave to change configuration settings to skip reverse hostname lookup on connecting and to enable the slow query log. I edited /etc/my.cnf making only these changes, then restarted mysqld with /etc/init.d/mysql restart All appeared to be well but when I connect to msyqld remotely or locally though it connects okay a slight problem is that mysqld crashes whenever you try to issue any kind of statement. The client looks like: Reading table information for completion of table and column names You can turn off this feature to get a quicker startup with -A Welcome to the MySQL monitor. Commands end with ; or \g. Your MySQL connection id is 3 Server version: 5.1.31-1ubuntu2-log Type 'help;' or '\h' for help. Type '\c' to clear the buffer. mysql> show tables; ERROR 2006 (HY000): MySQL server has gone away No connection. Trying to reconnect... Connection id: 1 Current database: mydb ERROR 2006 (HY000): MySQL server has gone away No connection. Trying to reconnect... ERROR 2003 (HY000): Can't connect to MySQL server on 'xx.xx.xx.xx' (61) ERROR: Can't connect to the server ERROR 2006 (HY000): MySQL server has gone away No connection. Trying to reconnect... ERROR 2003 (HY000): Can't connect to MySQL server on 'xx.xx.xx.xx' (61) ERROR: Can't connect to the server ERROR 2006 (HY000): MySQL server has gone away Bus error The mysqld error log looks like: 101210 16:35:51 InnoDB: Error: (1500) Couldn't read the MAX(job_id) autoinc value from the index (PRIMARY). 101210 16:35:51 InnoDB: Assertion failure in thread 140245598570832 in file handler/ha_innodb.cc line 2595 InnoDB: Failing assertion: error == DB_SUCCESS InnoDB: We intentionally generate a memory trap. InnoDB: Submit a detailed bug report to http://bugs.mysql.com. InnoDB: If you get repeated assertion failures or crashes, even InnoDB: immediately after the mysqld startup, there may be InnoDB: corruption in the InnoDB tablespace. Please refer to InnoDB: http://dev.mysql.com/doc/refman/5.1/en/forcing-recovery.html InnoDB: about forcing recovery. 101210 16:35:51 - mysqld got signal 6 ; This could be because you hit a bug. It is also possible that this binary or one of the libraries it was linked against is corrupt, improperly built, or misconfigured. This error can also be caused by malfunctioning hardware. We will try our best to scrape up some info that will hopefully help diagnose the problem, but since we have already crashed, something is definitely wrong and this may fail. key_buffer_size=16777216 read_buffer_size=131072 max_used_connections=3 max_threads=600 threads_connected=3 It is possible that mysqld could use up to key_buffer_size + (read_buffer_size + sort_buffer_size)*max_threads = 1328077 K bytes of memory Hope that's ok; if not, decrease some variables in the equation. thd: 0x18209220 Attempting backtrace. You can use the following information to find out where mysqld died. If you see no messages after this, something went terribly wrong... stack_bottom = 0x7f8d791580d0 thread_stack 0x20000 /usr/sbin/mysqld(my_print_stacktrace+0x29) [0x8b4f89] /usr/sbin/mysqld(handle_segfault+0x383) [0x5f8f03] /lib/libpthread.so.0 [0x7f902a76a080] /lib/libc.so.6(gsignal+0x35) [0x7f90291f8fb5] /lib/libc.so.6(abort+0x183) [0x7f90291fabc3] /usr/sbin/mysqld(ha_innobase::open(char const*, int, unsigned int)+0x41b) [0x781f4b] /usr/sbin/mysqld(handler::ha_open(st_table*, char const*, int, int)+0x3f) [0x6db00f] /usr/sbin/mysqld(open_table_from_share(THD*, st_table_share*, char const*, unsigned int, unsigned int, unsigned int, st_table*, bool)+0x57a) [0x64760a] /usr/sbin/mysqld [0x63f281] /usr/sbin/mysqld(open_table(THD*, TABLE_LIST*, st_mem_root*, bool*, unsigned int)+0x626) [0x641e16] /usr/sbin/mysqld(open_tables(THD*, TABLE_LIST**, unsigned int*, unsigned int)+0x5db) [0x6429cb] /usr/sbin/mysqld(open_normal_and_derived_tables(THD*, TABLE_LIST*, unsigned int)+0x1e) [0x642b0e] /usr/sbin/mysqld(mysqld_list_fields(THD*, TABLE_LIST*, char const*)+0x22) [0x70b292] /usr/sbin/mysqld(dispatch_command(enum_server_command, THD*, char*, unsigned int)+0x146d) [0x60dc1d] /usr/sbin/mysqld(do_command(THD*)+0xe8) [0x60dda8] /usr/sbin/mysqld(handle_one_connection+0x226) [0x601426] /lib/libpthread.so.0 [0x7f902a7623ba] /lib/libc.so.6(clone+0x6d) [0x7f90292abfcd] Trying to get some variables. Some pointers may be invalid and cause the dump to abort... thd->query at 0x18213c70 = thd->thread_id=3 thd->killed=NOT_KILLED The manual page at http://dev.mysql.com/doc/mysql/en/crashing.html contains information that should help you find out what is causing the crash. 101210 16:35:51 mysqld_safe Number of processes running now: 0 101210 16:35:51 mysqld_safe mysqld restarted InnoDB: The log sequence number in ibdata files does not match InnoDB: the log sequence number in the ib_logfiles! 101210 16:35:54 InnoDB: Database was not shut down normally! InnoDB: Starting crash recovery. InnoDB: Reading tablespace information from the .ibd files... InnoDB: Restoring possible half-written data pages from the doublewrite InnoDB: buffer... 101210 16:35:56 InnoDB: Started; log sequence number 456 143528628 101210 16:35:56 [Warning] 'user' entry 'root@PSDB102' ignored in --skip-name-resolve mode. 101210 16:35:56 [Warning] Neither --relay-log nor --relay-log-index were used; so replication may break when this MySQL server acts as a slave and has his hostname changed!! Please use '--relay-log=mysqld-relay-bin' to avoid this problem. 101210 16:35:56 [Note] Event Scheduler: Loaded 0 events 101210 16:35:56 [Note] /usr/sbin/mysqld: ready for connections. Version: '5.1.31-1ubuntu2-log' socket: '/var/run/mysqld/mysqld.sock' port: 3306 (Ubuntu) 101210 16:36:11 InnoDB: Error: (1500) Couldn't read the MAX(job_id) autoinc value from the index (PRIMARY). 101210 16:36:11 InnoDB: Assertion failure in thread 139955151501648 in file handler/ha_innodb.cc line 2595 InnoDB: Failing assertion: error == DB_SUCCESS InnoDB: We intentionally generate a memory trap. InnoDB: Submit a detailed bug report to http://bugs.mysql.com. InnoDB: If you get repeated assertion failures or crashes, even InnoDB: immediately after the mysqld startup, there may be InnoDB: corruption in the InnoDB tablespace. Please refer to InnoDB: http://dev.mysql.com/doc/refman/5.1/en/forcing-recovery.html InnoDB: about forcing recovery. 101210 16:36:11 - mysqld got signal 6 ; This could be because you hit a bug. It is also possible that this binary or one of the libraries it was linked against is corrupt, improperly built, or misconfigured. This error can also be caused by malfunctioning hardware. We will try our best to scrape up some info that will hopefully help diagnose the problem, but since we have already crashed, something is definitely wrong and this may fail. key_buffer_size=16777216 read_buffer_size=131072 max_used_connections=1 max_threads=600 threads_connected=1 It is possible that mysqld could use up to key_buffer_size + (read_buffer_size + sort_buffer_size)*max_threads = 1328077 K bytes of memory Hope that's ok; if not, decrease some variables in the equation. thd: 0x18588720 Attempting backtrace. You can use the following information to find out where mysqld died. If you see no messages after this, something went terribly wrong... stack_bottom = 0x7f49d916f0d0 thread_stack 0x20000 /usr/sbin/mysqld(my_print_stacktrace+0x29) [0x8b4f89] /usr/sbin/mysqld(handle_segfault+0x383) [0x5f8f03] /lib/libpthread.so.0 [0x7f4c8a73f080] /lib/libc.so.6(gsignal+0x35) [0x7f4c891cdfb5] /lib/libc.so.6(abort+0x183) [0x7f4c891cfbc3] /usr/sbin/mysqld(ha_innobase::open(char const*, int, unsigned int)+0x41b) [0x781f4b] /usr/sbin/mysqld(handler::ha_open(st_table*, char const*, int, int)+0x3f) [0x6db00f] /usr/sbin/mysqld(open_table_from_share(THD*, st_table_share*, char const*, unsigned int, unsigned int, unsigned int, st_table*, bool)+0x57a) [0x64760a] /usr/sbin/mysqld [0x63f281] /usr/sbin/mysqld(open_table(THD*, TABLE_LIST*, st_mem_root*, bool*, unsigned int)+0x626) [0x641e16] /usr/sbin/mysqld(open_tables(THD*, TABLE_LIST**, unsigned int*, unsigned int)+0x5db) [0x6429cb] /usr/sbin/mysqld(open_normal_and_derived_tables(THD*, TABLE_LIST*, unsigned int)+0x1e) [0x642b0e] /usr/sbin/mysqld(mysqld_list_fields(THD*, TABLE_LIST*, char const*)+0x22) [0x70b292] /usr/sbin/mysqld(dispatch_command(enum_server_command, THD*, char*, unsigned int)+0x146d) [0x60dc1d] /usr/sbin/mysqld(do_command(THD*)+0xe8) [0x60dda8] /usr/sbin/mysqld(handle_one_connection+0x226) [0x601426] /lib/libpthread.so.0 [0x7f4c8a7373ba] /lib/libc.so.6(clone+0x6d) [0x7f4c89280fcd] Trying to get some variables. Some pointers may be invalid and cause the dump to abort... thd->query at 0x18599950 = thd->thread_id=1 thd->killed=NOT_KILLED The manual page at http://dev.mysql.com/doc/mysql/en/crashing.html contains information that should help you find out what is causing the crash. 101210 16:36:11 mysqld_safe Number of processes running now: 0 101210 16:36:11 mysqld_safe mysqld restarted The config is [mysqld_safe] socket = /var/run/mysqld/mysqld.sock nice = 0 [mysqld] innodb_file_per_table innodb_buffer_pool_size=10G innodb_log_buffer_size=4M innodb_flush_log_at_trx_commit=2 innodb_thread_concurrency=8 skip-slave-start server-id=3 # # * IMPORTANT # If you make changes to these settings and your system uses apparmor, you may # also need to also adjust /etc/apparmor.d/usr.sbin.mysqld. # user = mysql pid-file = /var/run/mysqld/mysqld.pid socket = /var/run/mysqld/mysqld.sock port = 3306 basedir = /usr datadir = /DB2/mysql tmpdir = /tmp skip-external-locking # # Instead of skip-networking the default is now to listen only on # localhost which is more compatible and is not less secure. #bind-address = 127.0.0.1 # # * Fine Tuning # key_buffer = 16M max_allowed_packet = 16M thread_stack = 128K thread_cache_size = 8 # This replaces the startup script and checks MyISAM tables if needed # the first time they are touched myisam-recover = BACKUP max_connections = 600 #table_cache = 64 #thread_concurrency = 10 # # * Query Cache Configuration # query_cache_limit = 1M query_cache_size = 32M # skip-federated slow-query-log skip-name-resolve Update: I followed the instructions as per http://dev.mysql.com/doc/refman/5.1/en/forcing-innodb-recovery.html and set innodb_force_recovery = 4 and the logs are showing a different error but the behavior is still the same: 101210 19:14:15 mysqld_safe mysqld restarted 101210 19:14:19 InnoDB: Started; log sequence number 456 143528628 InnoDB: !!! innodb_force_recovery is set to 4 !!! 101210 19:14:19 [Warning] 'user' entry 'root@PSDB102' ignored in --skip-name-resolve mode. 101210 19:14:19 [Warning] Neither --relay-log nor --relay-log-index were used; so replication may break when this MySQL server acts as a slave and has his hostname changed!! Please use '--relay-log=mysqld-relay-bin' to avoid this problem. 101210 19:14:19 [Note] Event Scheduler: Loaded 0 events 101210 19:14:19 [Note] /usr/sbin/mysqld: ready for connections. Version: '5.1.31-1ubuntu2-log' socket: '/var/run/mysqld/mysqld.sock' port: 3306 (Ubuntu) 101210 19:14:32 InnoDB: error: space object of table mydb/__twitter_friend, InnoDB: space id 1602 did not exist in memory. Retrying an open. 101210 19:14:32 InnoDB: error: space object of table mydb/access_request, InnoDB: space id 1318 did not exist in memory. Retrying an open. 101210 19:14:32 InnoDB: error: space object of table mydb/activity, InnoDB: space id 1595 did not exist in memory. Retrying an open. 101210 19:14:32 - mysqld got signal 11 ; This could be because you hit a bug. It is also possible that this binary or one of the libraries it was linked against is corrupt, improperly built, or misconfigured. This error can also be caused by malfunctioning hardware. We will try our best to scrape up some info that will hopefully help diagnose the problem, but since we have already crashed, something is definitely wrong and this may fail. key_buffer_size=16777216 read_buffer_size=131072 max_used_connections=1 max_threads=600 threads_connected=1 It is possible that mysqld could use up to key_buffer_size + (read_buffer_size + sort_buffer_size)*max_threads = 1328077 K bytes of memory Hope that's ok; if not, decrease some variables in the equation. thd: 0x1753c070 Attempting backtrace. You can use the following information to find out where mysqld died. If you see no messages after this, something went terribly wrong... stack_bottom = 0x7f7a0b5800d0 thread_stack 0x20000 /usr/sbin/mysqld(my_print_stacktrace+0x29) [0x8b4f89] /usr/sbin/mysqld(handle_segfault+0x383) [0x5f8f03] /lib/libpthread.so.0 [0x7f7cbc350080] /usr/sbin/mysqld(ha_innobase::innobase_get_index(unsigned int)+0x46) [0x77c516] /usr/sbin/mysqld(ha_innobase::innobase_initialize_autoinc()+0x40) [0x77c640] /usr/sbin/mysqld(ha_innobase::open(char const*, int, unsigned int)+0x3f3) [0x781f23] /usr/sbin/mysqld(handler::ha_open(st_table*, char const*, int, int)+0x3f) [0x6db00f] /usr/sbin/mysqld(open_table_from_share(THD*, st_table_share*, char const*, unsigned int, unsigned int, unsigned int, st_table*, bool)+0x57a) [0x64760a] /usr/sbin/mysqld [0x63f281] /usr/sbin/mysqld(open_table(THD*, TABLE_LIST*, st_mem_root*, bool*, unsigned int)+0x626) [0x641e16] /usr/sbin/mysqld(open_tables(THD*, TABLE_LIST**, unsigned int*, unsigned int)+0x5db) [0x6429cb] /usr/sbin/mysqld(open_normal_and_derived_tables(THD*, TABLE_LIST*, unsigned int)+0x1e) [0x642b0e] /usr/sbin/mysqld(mysqld_list_fields(THD*, TABLE_LIST*, char const*)+0x22) [0x70b292] /usr/sbin/mysqld(dispatch_command(enum_server_command, THD*, char*, unsigned int)+0x146d) [0x60dc1d] /usr/sbin/mysqld(do_command(THD*)+0xe8) [0x60dda8] /usr/sbin/mysqld(handle_one_connection+0x226) [0x601426] /lib/libpthread.so.0 [0x7f7cbc3483ba] /lib/libc.so.6(clone+0x6d) [0x7f7cbae91fcd] Trying to get some variables. Some pointers may be invalid and cause the dump to abort... thd->query at 0x1754d690 = thd->thread_id=1 thd->killed=NOT_KILLED The manual page at http://dev.mysql.com/doc/mysql/en/crashing.html contains information that should help you find out what is causing the crash.

  Read the article

• PanelCollection Confusion ... or, what is an event root ?

  - by frank.nimphius

  Normal 0 false false false EN-US X-NONE X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} A command button added to the toolbar of a Panel Collection component does not cause field validation in a form when pressed. While this appears confusing it works as designed. Instead of a full page re-rendering, ADF Faces events and components can trigger partial page refresh, in which only portions of a page are refresh upon a request. In addition, some components - including the af:popup and af:subForm - represent event roots. Event roots don't propagated event notification outside of the component tag boundary, which means that the ADF Faces lifecycle only executed on components that are children of the event root component. The PanelCollection component is an event root and therefore only validates and refreshes data of its child components.

  Read the article

• Simple UPDATE query with (sometime) long query times

  - by Eric

  I run a dedicated MySQL server (2 cores, 16GB RAM) serving 100-200 requests per second. It is getting sluggish during peak traffic and I have a hard time optimizing the server. So I'm looking for some ideas now that I have done lots of Innodb fine-tuning with the "TUNING PRIMER" The query that now generates most slow queries is the following (see result from mysqldumpslow): Count: 433 Time=3.40s (1470s) Lock=0.00s (0s) Rows=0.0 (0), UPDATE user_sessions SET tid='S' WHERE idsession='S' I am very surprised to have so many long queries for such a simple query with no locking. Fyi, the table is InnoDB and has 14000 rows. It contains all active sessions on the site with approx 10 UPDATE and SELECT hits per second. Here is its structure: CREATE TABLE `user_sessions` ( `personid` mediumint(9) NOT NULL DEFAULT '0', `ip` varchar(18) COLLATE utf8_unicode_ci NOT NULL, `idsession` varchar(32) COLLATE utf8_unicode_ci NOT NULL, `datum` date NOT NULL DEFAULT '0000-00-00', `tid` time NOT NULL DEFAULT '00:00:00', `status` tinyint(4) NOT NULL DEFAULT '0', KEY `personid` (`personid`), KEY `idsession` (`idsession`), KEY `datum` (`datum`) ) ENGINE=InnoDB DEFAULT CHARSET=utf8 COLLATE=utf8_unicode_ci Any ideas?

  Read the article

• Oracle's Sun Blade modular systems: Can they give VBlock a run for their money?

  - by llaszews

  Check out these new hardware and software integrated solutions from Oracle Sun (they are not Exa* machines): http://www.oracle.com/us/products/servers-storage/servers/blades/index.html They offer a number of solutions not offered by VBlock: Oracle DB, Oracle WebLogic, OS and end to end management. Be interesting to see how much adoption these machines get given the long time VBlock has been around and the Exa* focused strategy at Oracle.

  Read the article

• Generalise variable usage inside code

  - by Shirish11

  I would like to know if it is a good practice to generalize variables (use single variable to store all the values). Consider simple example Strings querycre,queryins,queryup,querydel; querycre = 'Create table XYZ ...'; execute querycre ; queryins = 'Insert into XYZ ...'; execute queryins ; queryup = 'Update XYZ set ...'; execute queryup; querydel = 'Delete from XYZ ...'; execute querydel ; and Strings query; query= 'Create table XYZ ... '; execute query ; query= 'Insert into XYZ ...'; execute query ; query= 'Update XYZ set ...'; execute query ; query= 'Delete from XYZ ...'; execute query ; In first case I use 4 strings each storing data to perform the actions mentioned in their suffixes. In second case just 1 variable to store all kinds the data. Having different variables makes it easier for someone else to read and understand it better. But having too many of them makes it difficult to manage. Also does having too many variables hamper my performance?

  Read the article

• keeping connection open all time in sql

  - by Costi

  I have developed a Windows application in c# in which multiple users can add some numbers and their name and can view the data entered. The problem that I have is that the sever is on my laptop and every time I log off or close my laptop, they are losing connection to the DB and can not add or view any more. It seems that the port is closed or something. Is there a way to keep the port and their connection established all the time even when I'm logging out?

  Read the article

• How-to create a select one choice listing common time zones

  - by frank.nimphius

  Normal 0 false false false EN-US X-NONE X-NONE /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:11.0pt; font-family:"Calibri","sans-serif"; mso-ascii-font-family:Calibri; mso-ascii-theme-font:minor-latin; mso-fareast-font-family:"Times New Roman"; mso-fareast-theme-font:minor-fareast; mso-hansi-font-family:Calibri; mso-hansi-theme-font:minor-latin; mso-bidi-font-family:"Times New Roman"; mso-bidi-theme-font:minor-bidi;} ADF Faces provides an option to query a list of common timezones for display in a Select One Choice component. The EL expression for this is #{af:getCommonTimeZoneSelectItems()}. To use this expression in a Single Select One Choice component, drag and drop the component from the Oracle JDeveloper Component Palette into a JSF page.  In the opened dialog, copy the expression into the Value property below the Bind to list (select items) header. <af:selectOneChoice label="TimeZones" id="soc1">  <f:selectItems value="#{af:getCommonTimeZoneSelectItems()}"                          id="si1"/></af:selectOneChoice>

  Read the article

• Use MvcContrib Grid to Display a Grid of Data in ASP.NET MVC

  The past six articles in this series have looked at how to display a grid of data in an ASP.NET MVC application and how to implement features like sorting, paging, and filtering. In each of these past six tutorials we were responsible for generating the rendered markup for the grid. Our Views included the <table> tags, the <th> elements for the header row, and a foreach loop that emitted a series of <td> elements for each row to display in the grid. While this approach certainly works, it does lead to a bit of repetition and inflates the size of our Views. The ASP.NET MVC framework includes an HtmlHelper class that adds support for rendering HTML elements in a View. An instance of this class is available through the Html object, and is often used in a View to create action links (Html.ActionLink), textboxes (Html.TextBoxFor), and other HTML content. Such content could certainly be created by writing the markup by hand in the View; however, the HtmlHelper makes things easier by offering methods that emit common markup patterns. You can even create your own custom HTML Helpers by adding extension methods to the HtmlHelper class. MvcContrib is a popular, open source project that adds various functionality to the ASP.NET MVC framework. This includes a very versatile Grid HTML Helper that provides a strongly-typed way to construct a grid in your Views. Using MvcContrib's Grid HTML Helper you can ditch the <table>, <tr>, and <td> markup, and instead use syntax like Html.Grid(...). This article looks at using the MvcContrib Grid to display a grid of data in an ASP.NET MVC application. A future installment will show how to configure the MvcContrib Grid to support both sorting and paging. Read on to learn more! Read More >

  Read the article

• SUM of metric for normalized logical hierarchy

  - by Alex254

  Suppose there's a following table Table1, describing parent-child relationship and metric: Parent | Child | Metric (of a child) ------------------------------------ name0 | name1 | a name0 | name2 | b name1 | name3 | c name2 | name4 | d name2 | name5 | e name3 | name6 | f Characteristics: 1) Child always has 1 and only 1 parent; 2) Parent can have multiple children (name2 has name4 and name5 as children); 3) Number of levels in this "hierarchy" and number of children for any given parent are arbitrary and do not depend on each other; I need SQL request that will return result set with each name and a sum of metric of all its descendants down to the bottom level plus itself, so for this example table the result would be (look carefully at name1): Name | Metric ------------------ name1 | a + c + f name2 | b + d + e name3 | c + f name4 | d name5 | e name6 | f (name0 is irrelevant and can be excluded). It should be ANSI or Teradata SQL. I got as far as a recursive query that can return a SUM (metric) of all descendants of a given name: WITH RECURSIVE temp_table (Child, metric) AS ( SELECT root.Child, root.metric FROM table1 root WHERE root.Child = 'name1' UNION ALL SELECT indirect.Child, indirect.metric FROM temp_table direct, table1 indirect WHERE direct.Child = indirect.Parent) SELECT SUM(metric) FROM temp_table; Is there a way to turn this query into a function that takes name as an argument and returns this sum, so it can be called like this? SELECT Sum_Of_Descendants (Child) FROM Table1; Any suggestions about how to approach this from a different angle would be appreciated as well, because even if the above way is implementable, it will be of poor performance - there would be a lot of iterations of reading metrics (value f would be read 3 times in this example). Ideally, the query should read a metric of each name only once.

  Read the article

• /etc/postfix/transport missing; what should it look like?

  - by Thufir

  I'm following the mailman guide but couldn't locate /etc/postfix/ so created it as follows: root@dur:~# root@dur:~# cat /etc/postfix/transport dur.bounceme.net mailman: root@dur:~# root@dur:~# telnet localhost 25 Trying 127.0.0.1... Connected to localhost. Escape character is '^]'. 220 dur.bounceme.net ESMTP Postfix (Ubuntu) ehlo fqdn_test 250-dur.bounceme.net 250-PIPELINING 250-SIZE 10240000 250-VRFY 250-ETRN 250-STARTTLS 250-ENHANCEDSTATUSCODES 250-8BITMIME 250 DSN mail from:[email protected] 250 2.1.0 Ok rcpt to:thufir@localhost 451 4.3.0 <thufir@localhost>: Temporary lookup failure rcpt to:[email protected] 451 4.3.0 <[email protected]>: Temporary lookup failure quit 221 2.0.0 Bye Connection closed by foreign host. root@dur:~# root@dur:~# postconf -n alias_database = hash:/etc/aliases alias_maps = hash:/etc/aliases, hash:/var/lib/mailman/data/aliases append_dot_mydomain = no biff = no broken_sasl_auth_clients = yes config_directory = /etc/postfix default_transport = smtp home_mailbox = Maildir/ inet_interfaces = loopback-only mailbox_command = /usr/lib/dovecot/deliver -c /etc/dovecot/conf.d/01-mail-stack-delivery.conf -m "${EXTENSION}" mailbox_size_limit = 0 mailman_destination_recipient_limit = 1 mydestination = dur, dur.bounceme.net, localhost.bounceme.net, localhost myhostname = dur.bounceme.net mynetworks = 127.0.0.0/8 [::ffff:127.0.0.0]/104 [::1]/128 readme_directory = no recipient_delimiter = + relay_domains = lists.dur.bounceme.net relay_transport = relay relayhost = smtp_tls_session_cache_database = btree:${data_directory}/smtp_scache smtp_use_tls = yes smtpd_banner = $myhostname ESMTP $mail_name (Ubuntu) smtpd_recipient_restrictions = reject_unknown_sender_domain, reject_unknown_recipient_domain, reject_unauth_pipelining, permit_mynetworks, permit_sasl_authenticated, reject_unauth_destination smtpd_sasl_auth_enable = yes smtpd_sasl_authenticated_header = yes smtpd_sasl_local_domain = $myhostname smtpd_sasl_path = private/dovecot-auth smtpd_sasl_security_options = noanonymous smtpd_sasl_type = dovecot smtpd_tls_auth_only = yes smtpd_tls_cert_file = /etc/ssl/certs/ssl-mail.pem smtpd_tls_key_file = /etc/ssl/private/ssl-mail.key smtpd_tls_mandatory_ciphers = medium smtpd_tls_mandatory_protocols = SSLv3, TLSv1 smtpd_tls_received_header = yes smtpd_tls_session_cache_database = btree:${data_directory}/smtpd_scache smtpd_use_tls = yes tls_random_source = dev:/dev/urandom transport_maps = hash:/etc/postfix/transport root@dur:~# root@dur:~# tail /var/log/mail.log Aug 28 02:05:15 dur postfix/smtpd[20326]: connect from localhost[127.0.0.1] Aug 28 02:06:10 dur postfix/smtpd[20326]: warning: hash:/var/lib/mailman/data/aliases is unavailable. open database /var/lib/mailman/data/aliases.db: No such file or directory Aug 28 02:06:10 dur postfix/smtpd[20326]: warning: hash:/var/lib/mailman/data/aliases lookup error for "thufir@localhost" Aug 28 02:06:10 dur postfix/smtpd[20326]: NOQUEUE: reject: RCPT from localhost[127.0.0.1]: 451 4.3.0 <thufir@localhost>: Temporary lookup failure; from=<[email protected]> to=<thufir@localhost> proto=ESMTP helo=<fqdn_test> Aug 28 02:06:23 dur postfix/smtpd[20326]: warning: hash:/var/lib/mailman/data/aliases is unavailable. open database /var/lib/mailman/data/aliases.db: No such file or directory Aug 28 02:06:23 dur postfix/smtpd[20326]: warning: hash:/var/lib/mailman/data/aliases lookup error for "[email protected]" Aug 28 02:06:23 dur postfix/smtpd[20326]: NOQUEUE: reject: RCPT from localhost[127.0.0.1]: 451 4.3.0 <[email protected]>: Temporary lookup failure; from=<[email protected]> to=<[email protected]> proto=ESMTP helo=<fqdn_test> Aug 28 02:06:28 dur postfix/smtpd[20326]: disconnect from localhost[127.0.0.1] Aug 28 02:06:49 dur dovecot: pop3-login: Login: user=<thufir>, method=PLAIN, rip=127.0.0.1, lip=127.0.0.1, mpid=20338, TLS Aug 28 02:06:49 dur dovecot: pop3(thufir): Disconnected: Logged out top=0/0, retr=0/0, del=0/0, size=0 root@dur:~# The manual page is here.

  Read the article

< Previous Page | 595 596 597 598 599 600 601 602 603 604 605 606  | Next Page >