Search Results

Search found 1818 results on 73 pages for 'electronic cards'.

Page 60/73 | < Previous Page | 56 57 58 59 60 61 62 63 64 65 66 67  | Next Page >

• Compaq motherboard CQ60 AMD - nvidia chipsed graphic problem

  - by Dritan

  Hi! It nice to have read that you solved this problem this way. I have 2 laptops Compaq CQ60 AMD Athlon with Nvidia graphic cards. the first one is new, when i press power button, it lights up only the ON led in front and nothing else, no fan working, blank screen, no beep.. I don't know what may be the problem. When I put on power adaptor, it lights up only the side power led near dhe power adapter plug but it doesn't light up the front led one. the second one have this problem that it spins the fan, light power and On led, but it doesn't show nothing on the screen blank (even with external monitor). In this case it maybe this problem of the Nvida Graphic Chip and it may need a reflow. I have an hot air station, but I don't know if I should try this or the oven one. Please can you give me any suggestion what to do to solve this. I have read that the solution of the Oven method is just temporary,maximum of three months, do you have the same experience about this? Any suggestion is wellcome.

  Read the article

• Turning on Bluetooth disables wifi on Yoga 2

  - by Yostage

  I have a Lenovo Yoga 2. The moment that I turn on bluetooth, the wifi drops out - I lose connection, and connecting again shows "connection failed". If I turn the bluetooth off, wifi can reestablish fine. I've tried lots of different combinations of drivers for both the wifi and the bluetooth, but no combination has has changed this behavior yet. I've read some speculation that the cards have insufficient shielding, but that seems like kind of a large flaw to ship with. I've tried with a Carbon X1, a Yoga 2 Pro, and a Yoga 2 all next to each other on the desk while running InSSIDer. The X1 and the Y2P don't lose wifi connection when the bluetooth turns on, but the Y2 does immediately. The Y2P and the Y2 are running the same drivers for bluetooth and wifi, and appear to have the same wireless card internally. During the failure state, InSSIDer still sees signal strength for my network, but I cannot connect to it. stats: the card that comes in the laptop is an Intel Wireless-N 7260 Intel Bluetooth driver is at 17.0.1401.422 Intel Wireless driver is at 17.0.2.5 Windows 8.1 x64 Home wifi is a Medialink MWN-WAPR150N

  Read the article

• When machine is turned on, only the fan runs

  - by Gopal

  Hi, I have an issue slightly similar to this one posted here, http://superuser.com/questions/127016/troubleshooting-monitor-never-turns-on-system-fans-running-dvd-rom-does-not-op My configuration is as follows: EPOX 9NPA+ Ultra motherboard AMD Athlon 64 CPU Corsair 2 x 1GB PC3200 DDR RAM 1 DVD RW drive and 1 CD ROM Drive SATA 250 GB Hard drive 400W Power supply EVGA 256MB graphics card I have had this configuration for about four years. Last month, I started having issues in starting the machine. It wouldn't start when I press the ON button in the front of the case. So I used to pull out the power cord and plug it back in and then switch on in the front, and it used to work fine. And then one fine day, when I plugged in the power cord at the back, even without switching on the power-on button at the front, I saw that the fan at the back was running. So I opened the system. Then I could see that all the fans inside were running. I replaced the power supply. No luck there. Then I replaced the CMOS battery. Again nothing improved. Even when I removed all the cards and memory, I still get one short beep. That's it. Any idea how to proceed on this? Anything else could be checked? I want to confirm if this is a motherboard failure, before proceeding to replace it.

  Read the article

• Creating Routes using the second NIC in the box

  - by Aditya Sehgal

  OS: Linux I need some advice on how to set up the routing table. I have a box with two physical NIC cards eth0 & eth1 with two associated IPs IP1 & IP2 (both of the same subnet). I need to setup a route which will force all messages from IP1 towards IP3 (of the same subnet) to go via IP2. I have a raw socket capture program listening on IP2 (This is not for malicious use). I have set up the routing table as Destination Gateway Genmask Flags Metric Ref Use Iface IP3 IP2 255.255.255.255 UGH 0 0 0 eth1 If I try to specify eth0 while adding the above rule, I get an error "SIOCADDRT: Network is unreachable". I understand from the manpage of route that if the GW specified is a local interface, then that would be use as the outgoing interface. After setting up this rule, if i do a traceroute (-i eth0), the packet goes first to the default gateway and then to IP3. How do I force the packet originating from eth0 towards IP3 to first come to IP2. I cannot make changes to the routing table of the gateway. Please suggest.

  Read the article

• Bad Intel DQ965GF motherboard? Fails memtest, but memory is good.

  - by Boden

  I've got a machine with a DQ965GF motherboard. Two days ago it started locking up hard. Ran memtest 3.3, 1.7, and TestMem 4. TestMem just freezes, memtest failed on moving 8 bit inversions. Letting memtest run eventually causes the system to restart. I pulled memory sticks one by one, and then replaced the memory with a couple of known good sticks. No luck. I switched power supplies, didn't help. Swapped video cards just to be safe. No help. When I start the machine I get a single beep before it POSTs. According to the manual, a single beep means: 1 beep - Refresh Error (with nothing on the screen and it is not a video problem) I'm assuming that the motherboard has failed since it's obviously not a RAM or power issue. Do you agree? NOTE: I also tried resetting BIOS defaults, and even flashed the BIOS to the latest version. I also ran the Mersenne Prime Test and the CPU seems to click along just fine. (Tried logging in to superuser with openid but it's not working for me today. Hope this gets through)

  Read the article

• UPS power requirements for server

  - by captainentropy

  Greetings! So, I just placed an order for a new server. The company recommended that I get a 3000W UPS. (!) As best as I could I calculated the following wattage consumption based on benchmarked data or datasheets provided by the manufacturers of each component: number watts **total watts** MoBo 1 240 240 CPUs (E5540) 2 80 160 RAID cards (3ware) 2 18 36 RAM (6x4GB) 6 3 18 DVD drive 1 7 7 floppy 1 2 2 RE4 drives 8 7 56 WD20 drives 8 6 48 Intel X25 SSD 2 0.15 0.3 total = 567 So that is for the PSU requirements only. The PSUs in the machine are a 720W for the master node and 800W each for two subsystems. That's a total of 2320W that can be delivered by these PSUs. But that is 4X the amount being consumed, at most, by the components. I didn't count case fans or the eSATA card (3W maybe?) or what the PSUs themselves require but assuming I double or triple my calculations I'm not even remotely close to the 3000W UPS I was suggested to get. They run at least $1100. I could get a 2000W for about $750 or a 1500W for $450 and still be well over my estimated power need. I don't think I need a whole lot of run time in the case of a power outage, maybe 20 minutes max, enough time to shutdown if the power doesn't come on within 5-10 minutes. Any thoughts? Am I off on my calculations? Did I overlook something major? If so what are your suggestions for a UPS? Thanks!

  Read the article

• Ubuntu 10.10 - PC shutdown before boot shortly after BIOS loads

  - by clem

  Since installing Ubuntu 10.10 from Karmic I've started getting problems with starting up the PC. I've done a complete wipe (Boot and Nuke) of the hard drive and reinstalled Ubuntu 10.10 but the problem still occurs. There is no dual boot on the PC, just Ubuntu. Here is the problem: Each morning, when I turn the PC on from being off overnight, the PC starts up and loads the BIOS. I get the following message Verifying DMI Pool Data... K8 NPT Data Change...Update New Data to DMI!....... Then poof the computer shuts off. However, after switching the computer back on around 6 or 7 times after it's turned itself off, it will eventually boot up without any problem. Also, once up and running for a while, I can shutdown and restart the PC first time, without any issues. I have also noticed a problem with the USB mouse being recognised and once I finally get the computer booted up, I need to unplug and then plug the mouse back in to get it working. I've opened the PC up and checked the connections (cables, cards and memory) and it all seems fine. The main issue with troubleshooting this problem is I cannot test any suggestions or fixes until the next morning because once the computer is up and running it will remain so! I do not leave the computer on overnight to save energy. So.. Is this a hardware / boot software issue? This is a very odd problem and I have googled to no avail. Any suggestions?

  Read the article

• Why do manufacturers not show all hardware power usage?

  - by Drew

  I find it slightly more difficult to build a computer when I do not know how much power is needed for a component. When selecting a power supply for a computer, it is difficult to know how large of one to get. You don't want to go too large for cost reasons and circuit reasons, but you don't want to go too low and not be able to properly use every component. For instance, a graphics card might say "Minimum of a 500 Watt power supply. (Minimum recommended power supply with +12 Volt current rating of 30 Amps.)" But it really needs 360W (12V * 30A). So why don't they just say "Uses 360W max and xxxW peak"? Processors, I have noticed are good at reporting their power usage, but aside from processors and sometimes graphics cards, power usage is easily found. What is the power consumed by the Blu-ray / DVD drives? By the HDDs/SSDs? By the Mobo? etc. Why are these questions not easily answered when building a machine?

  Read the article

• Windows Explorer Hangs on Right-Click

  - by Bryan

  I am not sure if this is the right site to post this one as I typically post coding questions on stackoverflow. But I'll ask anyways and hopefully someone can move it if it's incorrect. Currently I have a customer built PC, utilizing an Intel i7 chip, 1300WATT PSU, 8Gigs of RAM, and two video cards. Originally I had the one video card (NVIDIA) that used the PSU and had two DVI output. After purchasing a third monitor I installed another ATI) graphics card not needed any PSU connectors. After installing and restarting, I noticed that when I right-click on my desktop, or through Windows Explorer it will hang, freeze then restarted. Sometimes after Windows Explorer restarts the problem dissipates. I checked to make sure everything was connected properly and it was. I repaired the ATI Catalyst Control Center to see if that had an issue, and I checked to see if either video card required updated drivers. Nothing worked. I tried restarting my PC and that didn't work. I tried using ShellXView (I forgot what it's actually called) and tried closed processes but that didn't work. Does anyone have any idea what could have caused this orpossible solutions I should try?< Thanks in advance.

  Read the article

• Slow Local Network, Windows 7, Snow Leopard, WiFi/Wired

  - by WerkkreW

  I am experiencing really poor local network performance in my home. I was recently using a Linksys WRT54G Router with DD-WRT on it, and a couple comparable Linksys-G PCI cards for connectivity but decided to upgrade hoping it would help with my performance issues. The computers in my house are connected as follows: Comcast Business Class Commercial 25mbps/10mbps (Verified) D-Link DGL-4500 Wireless N Router Windows 7x64 - D-Link DWA-552 Wireless-N Windows 7x64 - D-Link DWA-552 Wireless-N Mac Mini 10.6.2 - AirPort Extreme N Playstation 3, Hard Wired Xbox 360, Hard Wired Essentially the problem is very specific. Web browsing and uploading/downloading files from the internet is fine, more than fine. But if I want to say, Stream a video from one of my Windows 7 computers to my PS3, or copy a large video file between either of the PC's or the Mac, I get a consistent 500-900Kbps throughput at the high end. If I open my network browser, or try to browse my homegroup the response time is horrible. Both of my Windows computers are showing Strong wireless signals with a connection speed of 300Mbps. I know I can never expect to achieve anything near those speeds, but 500Kbps? Here is what I have tried so far: Enabled Single mode N-only and N/G Only on router WPA2 with AES Encrpytion Disabled "Remote Differential Compression" in Windows 7 Disabled TCP "Auto-Tuning" Used other software for file copies such as "Teracopy" I am at the end of my rope. Unfortunately I live in a 75 year old home with plaster walls, so hard-wiring my entire house isn't really an option I can handle right now. Any ideas to help me get decent speed when transferring files across my network would be greatly appreciated.

  Read the article

• Switching from Onboard intel to Nvidia Dedicated GPU

  - by Anarkie

  How can I switch from Intel onboard grpahics to Nvidia Dedicated GPU? When I go to windows screen resolution I see intel. I cant change it. I go to Device Manager, I see both Adapters are there and Nvidia is known.I disabled intel, I didnt see any option to set one as primary so I disabled intel, black screen!Reboot and re-enable intel. I right click on the desktop, choose "Nvidia Control Panel" and on 3D options I chose the desired game I want to play, High performance Nvidia, but it didnt switch when I started the game. Then I made preferred GPU in the global settings High performance Nvidia for everything it still didnt change.I understand to save the battery etc. there is a switch option between these two but I dont see this switch when it is necessary, I cant also switch manually?Is there a manual switch FN key?I looked but couldnt find. Why I want to do this? 1) Better game peformance. 2) I want to play an old game from 2002(Diablo 2 LOD), when I start the game there are black bars on the sides, so screen becomes just smaller which I dislike!I heard this is intel's specification to center the display.But instead I would like to scale or expand it to fit widescreen(fullscreen).Which should be possible with Nvidia. My Notebook Specs: Fujitsu Lifebook AH531, Win7 , 64 bit, i5, intel HD graphics onboard, Nvidia GT 525. I didnt install Nvidia later, it was always installed and ready from the moment I turned on the computer first time. How I determined that the cards werent switched when I am playing the game: with the windows key I exited from the game, then looked at screen resolutions menu, still saw intel, also the game was still with black bars.I know intel GPU should enough for Diablo 2 but I am interested in this answer for further games, I dont always play Diablo, what if I install an up to date game for example?Then Intel will not be sufficient.I would like to learn the switch option.

  Read the article

• Unexpected(?) high 'wasted' memory in memcached

  - by Nanne

  Looking at our memcached stats I think I have found an issue I was not aware of before. It seems that we have a strangely high amount of wasted space. I checked with phpmemcacheadmin for a change, and found this image staring at me: Now I was under the impression that the worst-case scenario would be that there is 50% waste, although I am the first to admit not knowing all the details. I have read - amongst others- this page which is indeed somewhat old, but so is our version of memcached. I think I do understand how the system works (e.g.) I believe, but I have a hard time understanding how we could get to 76% wasted space. The eviction rate that phpmemcacheadmin shows is 2 ev/s, so there is some problem here. The primary question is: what can I do to fix this. I could throw more memory at it (there is some extra available I think), maybe I should fiddle with the slab config (is that even possible with this version?), maybe there are other options? Upgrading the memcached version is not a quickly available option. The secondairy question, out of curiosity, is of course if the rate of 75% (and rising) wasted space is expected, and if so, why. System: This is currently not something I can do anything about, I know the memcached version isn't the newest, but these are the cards I've been dealt. Memcached 1.4.5 Apache 2.2.17 PHP 5.3.5

  Read the article

• Laptop Most Likely to Have Good Driver Support

  - by ShabbyDoo

  Through numerous bad experiences, I have learned that the most likely cause of laptop "failure" is the lack of updated drivers for new operating systems. As an example, I have a perfectly good Thinkpad T42 at home which runs Windows 7 just fine for my purposes except that no compatible ATI video drivers are available, and the generic drivers have flicker effects. I recently saw an ASUS laptop which looked quite nice except that I would be beholden to them to release ATI video driver updates customized for it. And, I can't trust them to do that for more than six months. What laptops (manufacturer/line) should I consider so that I could expect at least a couple years of frequent updates? I plan on running Windows 7 and installing whatever successor comes out. I like Intel components (especially WiFi) because I can install their drivers directly from them, and they have a long history of providing updates for years after shipping a particular component. More generally, components from companies which are likely to update drivers frequently are good as long as I can install the component manufacturer-provided drivers without laptop-specific customization (like the ATI drivers). Also, if a component can be replaced easily, I am less concerned. For example, Dell stopped pumping out updated drivers for one of its mini-PCI WiFi cards. The solution was to buy an Intel replacement on eBay for $12! That's fine. I can deal with that. So, what laptops should I consider so that I'm not likely to be stuck between a rock and a hard place?

  Read the article

• Hyper-V: Dedicated NIC for Guests VMs

  - by TheLizardKing

  I have two NIC cards and created a private virtual network for my virtual machines and unchecked "Allow management operating system to share this network adapter" which basically turns my Guest NIC into this sorta shell of a NIC card on the host machine and the only thing checked in it's properties is "Microsoft Virtual Network Switch Protocol" which I am fine with. Everything works and everything is connected. My issue is that for some reason my guest (Ubuntu Server with legacy network drivers) is not talking properly to my DHCP server. Specifically my DHCP server reserves the guest's IP address using it's MAC address but the guest isn't picking it up. It's picking up any old IP it can get and I can't even ping the hostname from another PC on the network but it pings fine if I use the IP. I see the guest showing up in my DHCP table but I can't get the reservation to stick. Is there some reason it's only partially communicating with my DHCP server? Pinging it's hostname on itself reveals it's using 127.0.0.1 instead of it's network IP. Is this an issue with the legacy drivers used in Hyper-V?

  Read the article

• Linux virtualization choices with graphic acceleration / video card support

  - by Urbn

  I am in the process of building a new desktop machine for work and fun. I am looking to run a undecided flavor of Linux (guessing Ubuntu) as my primary OS and several Windows installs with a Windows 7 install for .net development and gaming as virtualized environments. From my previous experiences with virtualization software in Linux I was never able to find an application that offered descent video card support / graphic acceleration etc. to be capable of playing any games within one of the virtualized environments. And since I will be investing quite a bit of money into this system for gaming I would naturally want to find the best option available to achieve this setup. So Onto my question: Is there any virtualization software available for Linux that has full video card support, graphic acceleration and capable of taking advantage of everything the video cards have to offer within the virtualized environments? Or am I stuck with running Windows 7 as my primary OS and using virtualization for Linux and the other OS's? Also I have no preference on open/closed source and price range would be up to $175.00 to support at least 3 virtualized environments.

  Read the article

• linux routing issue

  - by Duc To

  Hi! I have 2 linksys routers which has linux running on it and using tomato firmware.. both has internet lines plugged on but only 1 acts as DHCP server (router 1) What I am having to achieve is that all packets goes to router 1 from internal IPs want to access internet will go out to that internet line but from 1 specific port, if router 1 detects packets from a specific source port (for ex: http port: 80), it will redirect that packet to router 2 and goes out to the internet from there.. I have found some documents which give solution that I will need a linux servers with 2 ethernet cards and then we plug both internet lines on that server and routing base on it but I do not want to do that because my boss does not want to have an extra work mantaining that server, besides, he says that the router itself already a linux one so why.. I tend to agree his points.. Can it be done or a seperate linux server acting as a router is a must? Thank you all in advance and really look forward in your replies.. I am newbie to linux network and it seems to be something out of my capacity to solve :( Your sincerely! Duc To

  Read the article

• Wired to wireless bridge in Linux

  - by adrianmcmenamin

  I am attempting to set up my Raspberry Pi as a bridge (but I think this is not a question specific to the hardware) - using Debian wheezy. I have a hostapd.conf: (some details changed for security)... interface=wlan0 bridge=br0 driver=nl80211 auth_algs=1 macaddr_acl=0 ignore_broadcast_ssid=0 logger_syslog=-1 logger_syslog_level=0 hw_mode=g ssid=MY_SSID channel=11 wep_default_key=0 wep_key0=MY_KEY wpa=0 (yes, I know WEP is no good) And this in /etc/network/interfaces auto lo iface lo inet loopback iface eth0 inet dhcp allow-hotplug wlan0 iface wlan0 inet manual wpa-roam /etc/wpa_supplicant/wpa_supplicant.conf iface default inet dhcp auto br0 iface br0 inet dhcp bridge-ports eth0 wlan0 Everything seems to come up ok, but I cannot associate with the bridged wireless connection - even though the flashing lights on the USB stick suggest packets are being exchanged. I have read somewhere that not all cards/devices will run in hostap mode - they won't pass packets in one direction: is that right? (The info was a bit old)- this my card: [ 3.663245] usb 1-1.3.1: new high-speed USB device number 5 using dwc_otg [ 3.794187] usb 1-1.3.1: New USB device found, idVendor=0cf3, idProduct=9271 [ 3.804321] usb 1-1.3.1: New USB device strings: Mfr=16, Product=32, SerialNumber=48 [ 3.816994] usb 1-1.3.1: Product: USB2.0 WLAN [ 3.823790] usb 1-1.3.1: Manufacturer: ATHEROS [ 3.830645] usb 1-1.3.1: SerialNumber: 12345 So, what have I got wrong here?

  Read the article

• How to configure network on Windows Server 2008

  - by Gokhan Ozturk

  I have a IBM x3400 Server Machine with Windows Server 2008 R2 installed on it. But, since I am not expert on networking I have some problems. These roles installed on my server: Active Directory DNS File Sharing Hyper-V ISS VPN There is two network card on them. I configured them like this: Local Connection 1: 192.168.30.3 255.255.255.0 192.168.30.2 127.0.0.1 Local Connection 2: 192.168.30.101 255.255.255.0 192.168.30.6 127.0.0.1 My problem is, when I use this Ip gateways, It is sharing internet to all computers. This is not I want. I want to use Local Connection 1 for internal network. I am giving all computers gateway and DNS IP as 192.168.30.3 The Local Connection 2 is for Hyper-V and VPN connections. 192.168.30.2 and 192.168.30.6 are my modem's gateways. I am using 192.168.30.6 external IP for VPN connections. There is two 24 port switches. There is a connection between them and this two ethernet card connected directly to them. And modems are connected to switches as well (Morems are not near the server. They are somewhere in the building). I disabled network Bridge and removed all ethernet cards from it. With this configuration, all computers can ping my server's IP (192.168.30.3) but on server I cannot ping any clients (Request timeout). What is the best way to configure my network? Thank you. Redgards

  Read the article

• No sound out of headphone port on laptop

  - by Thanatos

  I cannot get sound out of the headphone port on a laptop. Headphones are plugged in, and sound comes out of the internal speakers. Windows behaves normally (sound switches to headphones when headphones are inserted). It did work in Linux at one point, but something changed, we're just not sure what. Rebooting doesn't fix. This appears to occur whether or not PulseAudio is running. Things I've tried: Rebooting. No effect. Booting into Windows. It works properly, so probably not a hardware issue. All of alsamixer. My only controls are this: "Master" Volume bar & mutable, unmuted. Controls volume. "PCM" Volume bar only. 100%. "S/PDIF" Mutable only, currently muted, has no effect. "S/PDIF" Default PCM", Mutable only, currently unmuted, has no effect. Killing PulseAudio. No effect. (It also won't stay dead! Something appears to be restarting it, and I can't tell what, but it is annoying as fuck.) alsactl init 0, no effect. sudo rm -f /var/lib/alsa/asound.state, no effect. General system info: Ubuntu 10.04 LTS Toshiba Satellite T135D-S1324 lspci says I have: 00:14.2 Audio device: ATI Technologies Inc SBx00 Azalia (Intel HDA) 01:05.1 Audio device: ATI Technologies Inc RS780 Azalia controller Some edits: Yes, the headphones are in all the way. This works in Windows: You plug headphones in, the internal speakers stop making noise, and noise comes out the head phones. Windows says I only have two sound cards: the HDMI port (which I don't care about) and the "sound card", which it claims is a "Conexant Pebble High Definition SmartAudio" In Windows, both the internal speakers and the headphone jack show up as one soundcard, which in my experience, is typical. (This is a laptop)

  Read the article

• What was your biggest waste of money, and what should you have bought instead? [closed]

  - by rob

  I waste a lot of money on computer equipment and other electronics that I don't really need. I've also bought software that I've never really used, or which as been replaced by better free software. As I'm buying things, it doesn't seem like much--fifty bucks here, a hundred dollars there. But when I go back and look at how much I've spent over my past few electronics purchases, I usually start to think of the other things I could have bought with that money instead. Most of the computer hardware and electronics don't usually improve my life by much, if at all. Case in point: back when I was in college, I prided myself on getting the best deals for computer hardware, but when I went back and added up all the money I had spent, I had probably wasted close to a thousand dollars on "cheap" $100 hard drives that eventually all went bad (including the warranty replacements). Even if they did still work, it would not be worth the effort to use them, because they're too small and too noisy by today's standards. I've also spent thousands more on other junk, such as RAM and CPU upgrades that only gave modest performance jumps, and wireless audio transmitters that I used for a short time to stream music from the now-defunct Yahoo! Music service. Every time I see a really great deal on RAM or video cards, I come one click away from buying them, but these days I'm usually able to resist. I've been wanting to get into woodworking ever since I moved into my house, and five years later I'm finally saving up for a $600 table saw. Sure, I've already got a toolbox and a couple of the essential power tools like a drill and a jigsaw, but I can't help but think that I'd have an entire shop full of woodworking tools and a lot of nice wood furniture if I hadn't wasted all that money back in college. What has been your biggest waste of money on computer stuff and technology? If you had all that money back, would you make the same mistake again and buy the same types of things, or would you spend it on something else?

  Read the article

• Disappeared graphics card

  - by lenovo user

  I have a Lenovo T520 with two graphics cards, an nVidia quadro and an intel graphics card. I'm running a Ubuntu and Windows 7 dual boot. I can no longer find any trace of my intel graphics card. In my linux boot: > lspci | grep VGA > 01:00.0 VGA compatible controller: nVidia Corporation GF106 [Quadro 2000M] (rev a1) In Windows in control panel display- advanced settings, I only see the NVIDIA Quadro 2000M. In the BIOS there is no mention of the intel graphics card, no where I can find to try and turn it on or off. I thought I was going crazy, but then I found a post I made on ask ubuntu I made 3 months ago where I listed the output of lspci on this same machine: lspci | grep VGA 00:02.0 VGA compatible controller: Intel Corporation 2nd Generation Core Processor Family Integrated Graphics Controller (rev 09) 01:00.0 VGA compatible controller: nVidia Corporation GF106 [Quadro 2000M] (rev a1) What is going on? How could my intel graphics card have been disabled or turned off somehow without my knowledge? I've been in the BIOS 3 times now, each time convinced the last time I must have missed something, but I always find nothing. Am I missing something there? Could a thief have opened my computer and stolen my graphics card?

  Read the article

• Expresscard Not Detected in PCI-E Adapter

  - by maxpower47

  I'm trying to put an expresscard TV tuner (Avermedia HC82) into my HTPC using this expresscard to PCI-E adapter. I've verified that the tuner works fine in my laptop. The motherboard is a Biostar TF7050-M2. When I install it and turn it on, the light on the back of the adapter comes on fine (there are two indicator lights on the back to show if it is using PCI-E or USB communication, USB communication goes through a USB cable connected between the card and a header on the motherboard) showing that it is working in PCI-E mode. However, the device is never detected in Windows 7 Professional x64. The auto detect never happens, it doesn't show up in the device manager, and I can have it rescan for new hardware and nothing is found. I tested the whole setup (tuner + adapter) in another PC (also using Win 7 Pro x64) and it worked fine. I also tried: Plugging the adapter in to the PCI-E x16 slot on the motherboard (I verified first that the x16 slot worked by installing a video card in it) Booting into safe mode and rescanning Updating the chipset drivers Installing the tuner drivers first Using a different USB cable, plugged in to one of the known good ports on the back of the board Trying it without the USB cable plugged in Removing the other PCI cards that were installed on the board Looking through the BIOS for any setting that might be disabling it somehow to no avail. I'm at a loss for what else to try. I really don't want to RMA it (the shipping back to newegg will be almost as much as it cost to buy in the first place. Any ideas?

  Read the article

• Multi monitor setup with a tv as well?

  - by jasondavis

  I have always had a dual monitor setup for my pc's for years now. I am now in the market to build a new PC and get some new stuff. I need some help or advice on how to run 3 monitors WITH a 4th display which will be a lcd/plasma tv. So I am thinking I can get 2 video cards and that will give me all the hookups to run 3 monitors instead of 2. I will mount all 3 monitors in a row side by side and above them on the wall I would like to mount a larger 30-40+ inch lcd or plasma tv. I would then like to hook up my atelite/cable to this tv just as I would normally hook up a tv but I would like to also be able to have an option to view my PC o this tv as well. I know that is possible but would it be possible to view my PC on that tv and also still view my 3 other monitors and have the TV be a 4th display, where I could dock a different app/window in windows in all 4 displays (3 monitors + tv) ?? Please tell me any tips/advice on how to do this including what cables/software if any/converters/ you name it. Thanks for any help

  Read the article

• Is there a historical computer peripherals or accessories museum or even just a current list?

  - by zimmer62

  Thinking about all the unique and different peripherals I've owned over the years, from ISA capture cards, to parallel port controlled shutter glasses for 3d games. I've seen many many accessory or computer peripherals come and go. The nostalgia of these things is a lot of fun. I tried to find some sort of historical time-line or list but what mostly turned up is computers themselves. I'm more interested in the mice, scanners, the weird adapters that shouldn't exist, short run very rare products, strange devices from computer shows in the 80's and 90's... Hardware you might find in a geeks basement that would be completely useless now, but was the coolest thing around when it was new. An example would be a drawing tablet I had for my TI-99 computer, or the audio tape player accessory for a C64 which let you save files to audio tapes, An ISA card that did the same for PC's hooked up to a VCR. Remember that IBM-PC Jr upgrade kit, that added a floppy drive, more memory and the AT switch in the back? I'd love to find either a wiki, or a list that has already been assembled which contain many of these weird (or common) accessories. I've had so many over the years I suppose I could start a wiki here if such a list doesn't already exist.

  Read the article

• sbs-server with 2 nics and 2 connections to the internet with different providers not working as it

  - by erik-van-gorp

  We have the following configuration : A sbs-2003 server in a domain (mydomain.com) with 2 network cards, each connected to a different network (provider), with different gateways, one for web and one for mail and clients. (we do this because the bandwitdh we get from our providers is too small to handle all the mail(+spam) traffic and webservices, so we took 2 providers) DNS is as follows : www.mydomain.com 1.2.3.4 mail.mydomain.com 5.6.7.8 NIC 1(192.168.1.3) is connected to to the internet through a firewall at 192.168.1.1, having wan address 1.2.3.4 NIC 2(10.0.0.3) is connected to to the internet through a firewall at 10.0.0.1, having wan address 5.6.7.8 Both nics have their default gateway installed at their corresponding routers. Also the metrics are set equal. (i know this isn't a supported config, but it works more or less). In this configuration i can use RDP on both wan adresses, and telnet to port 25 works as well on both. The issue now is that since a few weeks , we get regular disconnections, and website hickups(timeouts), several per hour. If we set one router to a higher metric, that route no longer works. In short, I want the mails to route through NIC2 and the web through NIC1. Any better configuration (without installing a second mail server) ?

  Read the article

< Previous Page | 56 57 58 59 60 61 62 63 64 65 66 67  | Next Page >