Search Results

Search found 21884 results on 876 pages for 'external address'.

Page 601/876 | < Previous Page | 597 598 599 600 601 602 603 604 605 606 607 608  | Next Page >

• Multicast in private LAN with different subnets

  - by Gobliins

  after i read Multicast IP Addresses and Multicast accross the subnets I am confused. Configuration: I have two devices in the same network. They may not be in the same Subnet, but always in the same physical network (beyond the same router, switch etc.) I want to communicate across IP multicast either 224.x.x.x or 239.x.x.x may be more fitting because we want it local, not beyond of forward through the router. Can one machine be the receiver and the other machine sender of the same multicast address? and can the receiving machine send an answer to the sending machine?

  Read the article

• Syntax of mac2vlan file in freeradius?

  - by Edik Mkoyan

  below is the content of mac2vlan file in freeradius When I uncomment this 00:01:02:03:04:05,VLAN1 it logs parsing error including configuration file /etc/raddb/modules/mac2vlan /etc/raddb/modules/mac2vlan[10]: Parse error after "00:01:02:03:04:05" Errors reading /etc/raddb/radiusd.conf what is the correct syntax? # -*- text -*- # # $Id$ # A simple file to map a MAC address to a VLAN. # # The file should be in the format MAC,VLAN # the VLAN name cannot have spaces in it, for example: # 00:01:02:03:04:05,VLAN1 # 03:04:05:06:07:08,VLAN2 # ... passwd mac2vlan { filename = ${confdir}/mac2vlan format = "*VMPS-Mac:=VMPS-VLAN-Name" delimiter = "," #}

  Read the article

• How come I can't ping my home computer?

  - by bikefixxer

  I'm trying to set up a vpn into my home computer in order to access files from wherever. I have the home computer set up with a no-ip dynamic dns program so I can always connect, and have also tried using the actual ip address. However, when I try to connect or even ping from anywhere outside of my house I can't get through. I've tried putting that particular computer in the dmz, turned off the computers firewall and anti-virus, and I still don't get anything. I have comcast as my home internet provider. I have also tried from two different locations. Are there any other solutions I can try or is comcast the issue? I used to be able to do this when I ran a small web server at home for fun but now nothing works. Thanks in advance for any suggestions!

  Read the article

• Bad archive mirror using PXE boot method

  - by user11566

  I'm trying to automatically install Ubuntu on a client PC by using the PXE BOOT method....my Objectives are below: I am following the steps given in this link installation using PXE BOOT the server will have a KICKSTART config file which contains the parameters for the OS installation and the files which are required for the OS installations. the client will have to detect this configuration along with the setup files and complete the installation without any input from the user. In my server I have installed DHCP3-server,Apache2 and TFTP to help me with the installation. I have nearly achieved my first objective, I am able to boot my client using the files stored in the server but during the installation stage it is asking me to CHOOSE A MIRROR OF UBUNTU ARCHIVE I gave the server's IP address and the path in the server where the files are located but then its giving me this error BAD ARCHIVE MIRROR So is it possible that instead of downloading all the files from the internet and storing them on my disk can I use the files which comes with the UBUNTU-CD, and how to store these files in what format (should I zip them) on the disk? secondly I am also generating the ks.cfg which I wanted to give to the client for automatic installation of the OS. So how should the configuration file be given to the installation process?

  Read the article

• DNS on Redhat - rdnc: no server specified and no default

  - by Syahmul Aziz

  Hi all. The error as shown in the 2 pictures below: The configurations for named.conf and the zones files as shown below: After applying "alveso" suggestion below. Now, I think there is no error but I still can't ping my own domain www.p0864868.com (10.0.0.1) nor can I do host or nslookup as shown on previous pictures. PLease assist. Thank you in advance. I also attached my the changes that I made to my named.conf as well as my resolve.conf configs as shown below: progress 2: turned on logging by typping "rndc queylog" The output as below when I pinged p0864868.com progress 3: changed permission of 10-0-0.zone and p086868.zone to 644 named:named Still can't ping www.p0864868.com or execute host command. It says something like network unreachable. I don't understand why it refer to I don't what address is that.

  Read the article

• How does one launch PhpPgAdmin?

  - by DarenW

  I just installed postgresql, php5 and in particular PhpPgAdmin using Ubuntu's synaptic app. The PHP is running fine, the http server (lighttpd) is working fine, and I can do pg a the command line. The only thing that remains a mystery is PhpPgAdmin - just how does one fire it up to use it? I am clueless about the proper means of starting PhpPgAdmin; it isn't explained anywhere on the site for it. I tried typing phppgadmin at a bash command prompt, and entering "http://phppgsdmin/" and "http://localhost/phppgadmin" as wild guesses in the address bar in a browser - nothing happens. What is the secret? BTW, i'm only serving http on localhost, doing purely private web development.

  Read the article

• Cannot connect to a VPN server - authentication failed with error code 691

  - by stacker

  When trying to connect to a VPN server, I get the 691 error code on the client, which say: Error Description: 691: The remote connection was denied because the user name and password combination you provided is not recognized, or the selected authentication protocol is not permitted on the remote access server. Now, I validated that the username and password are correct, and tried to login with domain name and without. I also installed a certification to use with the IKEv2 security type. I also validated that the VPN server support security method. But I cannot login. In the server log I get this log: Network Policy Server denied access to a user. The user DomainName\UserName connected from IP address but failed an authentication attempt due to the following reason: The remote connection was denied because the user name and password combination you provided is not recognized, or the selected authentication protocol is not permitted on the remote access server. Any idea of what can I do? Thanks in advance!

  Read the article

• Ubuntu and mysql server. Something isnt allowing me to connect

  - by acidzombie24

  I have a question about mysql settings http://serverfault.com/questions/94054/remote-connections-and-mysql-on-ubuntu/94088#94088 now i want to figure out why i cannot connect. I made sure bind-address was commented out. I can ping the server within the VM but i cannot ping it from within the VM using mysqladmin --protocol=tcp --host=self_ip ping. I also followed along and check if my ports were open and they look like they are. I setup samba on that VM and can access that with no problem as well. It looks like ubuntu does not have a firewall either (i figured this out before) so i am stumped why the server isnt allowing my connection. Apparently the config file works on another person side http://www.pastie.org/742545 I am using Ubuntu 6.06 LTS just because of 'support' reasons. So hopefully this will be 'easy'?

  Read the article

• Exchange Cached Mode (Exchange 2010) with Outlook 2003 and Outlook 2010 Causing Sync Issues

  - by Jason N. Gaylord

  We have Exchange 2010 and a mix of Outlook 2003 and Outlook 2010 clients. When Exchange Cached Mode is enabled, clients are receiving sync issues. In Outlook 2010, the sync issues are mainly with the Deleted Items. In Outlook 2003, they are mainly around the Offline Address Book. When Exchange Cached Mode is disabled, the clients notice a 3 second delay in deleting email in list view within the Inbox. Anyway that these two issues can be resolved? It's a big pain especially to the frustrated end users. TIA!!!!

  Read the article

• Should Exterrnal USB hard drive auto mount Ubuntu 12.04.01 LTS

  - by Chris Good

  I want to have external USB hard drives automatically mounted when plugged in. I have 2 drives exactly the same except for volume label. They both have the same UUID. I want to be easily able to swap them as I'm using them for backups and want to keep 1 at home for off site backup. I've set up the /etc/fstab so they should mount at different places based on their volume label: /etc/fstab : LABEL=Passport1 /media/Passport1 ntfs defaults,windows_names,locale=en_US.utf8 0 0 LABEL=Passport2 /media/Passport2 ntfs defaults,windows_names,locale=en_US.utf8 0 0 blkid shows : ... /dev/sdc1: LABEL="Passport2" UUID="4E1AEA7B1AEA6007" TYPE="ntfs" /dev/sdd1: LABEL="Passport1" UUID="4E1AEA7B1AEA6007" TYPE="ntfs" They both mount automatically during reboot but do not mount when just plugged in to a running system. I've read lots of stuff about this, much of it is old so I'm not sure if it applies. I've read some stuff that says the mounts should happen automatically when plugged in, and lots of other stuff that says you have to install other software to make this happen, although much of it just seems to set up the fstab. What's the real story? Here is /var/log/syslog when drive is plugged in: Dec 14 11:22:58 ausyvutims1 kernel: [66221.300196] usb 1-1: new high-speed USB device number 6 using ehci_hcd Dec 14 11:22:58 ausyvutims1 mtp-probe: checking bus 1, device 6: "/sys/devices/pci0000:00/0000:00:11.0/0000:02:03.0/usb1/1-1" Dec 14 11:22:58 ausyvutims1 mtp-probe: bus: 1, device: 6 was not an MTP device Dec 14 11:22:58 ausyvutims1 kernel: [66221.656020] scsi7 : usb-storage 1-1:1.0 Dec 14 11:22:59 ausyvutims1 kernel: [66222.661534] scsi 7:0:0:0: Direct-Access WD My Passport 0748 1016 PQ: 0 ANSI: 6 Dec 14 11:22:59 ausyvutims1 kernel: [66222.666466] scsi 7:0:0:1: Enclosure WD SES Device 1016 PQ: 0 ANSI: 6 Dec 14 11:22:59 ausyvutims1 kernel: [66222.667739] sd 7:0:0:0: Attached scsi generic sg3 type 0 Dec 14 11:22:59 ausyvutims1 kernel: [66222.667913] ses 7:0:0:1: Attached Enclosure device Dec 14 11:22:59 ausyvutims1 kernel: [66222.668047] ses 7:0:0:1: Attached scsi generic sg4 type 13 Dec 14 11:22:59 ausyvutims1 kernel: [66222.678473] sd 7:0:0:0: [sdc] 1953458176 512-byte logical blocks: (1.00 TB/931 GiB) Dec 14 11:22:59 ausyvutims1 kernel: [66222.687700] sd 7:0:0:0: [sdc] Write Protect is off Dec 14 11:22:59 ausyvutims1 kernel: [66222.687705] sd 7:0:0:0: [sdc] Mode Sense: 47 00 10 08 Dec 14 11:22:59 ausyvutims1 kernel: [66222.701076] sd 7:0:0:0: [sdc] No Caching mode page present Dec 14 11:22:59 ausyvutims1 kernel: [66222.701081] sd 7:0:0:0: [sdc] Assuming drive cache: write through Dec 14 11:22:59 ausyvutims1 kernel: [66222.738062] sd 7:0:0:0: [sdc] No Caching mode page present Dec 14 11:22:59 ausyvutims1 kernel: [66222.738068] sd 7:0:0:0: [sdc] Assuming drive cache: write through Dec 14 11:22:59 ausyvutims1 kernel: [66222.754558] sdc: sdc1 Dec 14 11:22:59 ausyvutims1 kernel: [66222.792006] sd 7:0:0:0: [sdc] No Caching mode page present Dec 14 11:22:59 ausyvutims1 kernel: [66222.792012] sd 7:0:0:0: [sdc] Assuming drive cache: write through Dec 14 11:22:59 ausyvutims1 kernel: [66222.792016] sd 7:0:0:0: [sdc] Attached SCSI disk Dec 14 11:22:59 ausyvutims1 ata_id[16971]: HDIO_GET_IDENTITY failed for '/dev/sdc': Invalid argument Thanks for any help offered

  Read the article

• Oracle Enterprise Manager 12c R3 introduces advancements in cloud lifecycle and operations management

  - by Anand Akela

  Oracle Enterprise Manager 12c Release 3 (R3) was announced ( Press Release ) earlier today. It is now available for download at  OTN . This latest release features improvements in several areas, including: Improvements to Private Cloud and Engineered Systems Management Expanded Middleware and Application Management Capabilities Efficiency Gains for Enterprise manager Users in EM’s Enterprise-Ready Framework You can learn more about what's new in the Oracle Enterprise Manager 12c R3 in the Enterprise Manager 12c documentation . You will see more blogs and details about the new features during the next few weeks. Please let us what On July 18th, you can join us at a webcast to hear Thomas Kurian, EVP of Product Development on what Oracle Engineering has achieved with Oracle Enterprise Manager 12c Release 3 to address these challenges. Later, during this webcast, Oracle experts will discuss the latest capabilities in Oracle Enterprise Manager 12c Release 3 for cloud lifecycle and operations management. The presentation will be followed by a live Q&A session with Oracle experts. You can also join us online on Twitter to get your specific questions answered. Please use hash tag #em12c to join the conversation. /* Style Definitions */ table.MsoNormalTable {mso-style-name:"Table Normal"; mso-tstyle-rowband-size:0; mso-tstyle-colband-size:0; mso-style-noshow:yes; mso-style-priority:99; mso-style-qformat:yes; mso-style-parent:""; mso-padding-alt:0in 5.4pt 0in 5.4pt; mso-para-margin:0in; mso-para-margin-bottom:.0001pt; mso-pagination:widow-orphan; font-size:10.0pt; font-family:"Times New Roman","serif";} Register Now for the Webcast! Stay Connected: Twitter |  Face book |  You Tube |  Linked in |  Newsletter

  Read the article

• Security Alert for CVE-2010-0886 and CVE-2010-0887 Released

  - by eric.maurice

  Hi, this is Eric Maurice again! Oracle just released a Security Alert to announce the availability of fixes for two vulnerabilities (CVE-2010-0886 and CVE-2010-0887) affecting Oracle Java SE and Oracle Java For Business. Both vulnerabilities only affect Java when running in a 32-bit web browser. These vulnerabilities are not present in Java running on servers or standalone Java desktop applications and do not impact any Oracle server based software. The first vulnerability (CVE-2010-0886) affects the Java Deployment Toolkit (version 6 update 10 through 19) on Windows only. The second vulnerability (CVE-2010-0887) affects the Java Plug-in (version 6 update 18 and 19) on Windows, Solaris and Linux. Both vulnerabilities may allow an attacker to run commands on the user's system with the privileges of the user, whose system may have become compromised by visiting a malicious web site. Oracle rated the severity of both vulnerabilities with a CVSS Base Score of 10.0 because many Windows users grant themselves administrative privileges. However, on other platforms, or for Windows users with limited privileges, the CVSS Base Score is only 7.5, because a successful exploitation of these vulnerabilities cannot result in a full compromise of the affected system. Users can quickly determine if they are running vulnerable versions of Java by pointing their browser to http://www.java.com/en/download/help/testvm.xml. Java SE users can visit http://www.java.com and download the most recent release of Java SE to address these vulnerabilities. Because of the criticality of these vulnerabilities, and the publicity they received as a result of their disclosure before the availability of a fix, Oracle recommends that all customers and Java users update their Java installation to the most recent version (6 update 20). For More Information: The advisory for the Security Alert for CVE-2010-0886 and CVE-2010-0887 is located at http://www.oracle.com/technology/deploy/security/alerts/alert-cve-2010-0886.html

  Read the article

• Instructor Insight: Dealing with Columns in Oracle JD Edwards Enterprise One Tools Release 9.1

  - by Breanne Cooley

  Oracle JD Edwards Enterprise One Tools Release  9.1 has many new features that will help end users be more efficient in their daily jobs. For example, hiding grid columns is now as easy as a left-mouse click. In earlier releases, users could click on the ‘Customize Grid’ link but still had to do several more clicks to hide or show a column . The following example shows how easy this new feature is to use. First, right-mouse click on the column you want to hide; for example the ‘Long Address’ column. The column is now hidden. Second, right-mouse over on any of the columns to show the ‘Unhide’ option. After you select ‘Unhide’, the hidden column is shown. You can then select the column to show, or unhide, the column. This new feature and others are covered in the JD Edwards EnterpriseOne System Administration Rel 9.x course, which has been updated to reflect the new release. Hope to see you in class! -Randy Richeson, Senior Principal Instructor, Oracle University

  Read the article

• Apache DVB http video Streaming bandwidth or priority problem

  - by igino manfre'

  I'm streaming few precompressed DVB videos from cloud. The streams are generated from VLC on "impossible" ports (such as 64085, 64086 etc) reverse proxed by Apache on port 80 and 8080. All the generated streams are listed in "http://95.110.164.61/indexv.html". From an ADSL connection with enough downlink bandwidth, recalling the stream generated by VLC (such as "http://95.110.164.61:64087/mpg2_6.4") it flows fluently. Recalling the same stream proxed by Apache ("http://95.110.164.61/mpg2_6.4") the stream stops and goes. The only situation in which the Apache proxed streams flow regularly is from a site connected through 64 Mbps warranted bandwith with RTT to the server less than 10 mseconds. Please note that streams below 2 Mbps are fluently proxed. The system is a single core xeon with windows 2008 R2 on 4 GB of RAM with 1 Gbps of network bandwidth. The drain of computational and bandwidth resources is negligeable, the RAM usage always lower than 50%. On the system I run many VLC streamers. Any of them drains a variable amount of RAM (from about 25 to 70 MB). On the contrary the couple of httpd.exe processes drain no more than 7 MB. Using Wireshark (on the server) I see that VLC directy send to the client much more packets than Apache, and the stream is framgmented on many frames. I'm not a programmer, a newby of Apache. Can anyone please address me to a specific portion of the Apache's huge documentation? Thank you. igino

  Read the article

• Is it still "wrong" to require TLS on incoming SMTP messages

  - by jackweirdy

  According to the STARTTLS Spec Section 5: A publicly-referenced SMTP server MUST NOT require use of the STARTTLS extension in order to deliver mail locally. This rule prevents the STARTTLS extension from damaging the interoperability of the Internet's SMTP infrastructure. A publicly-referenced SMTP server is an SMTP server which runs on port 25 of an Internet host listed in the MX record (or A record if an MX record is not present) for the domain name on the right hand side of an Internet mail address. However, this spec was written in 1999, and considering it's 2014, I'd expect most SMTP clients, servers, and relays to have some kind of implementation of STARTTLS. How much email can I expect to lose if I require TLS for incoming messages?

  Read the article

• DNS and IPs - Does DNS send the IP back to the client?

  - by Josh

  I ran across a site that talked about routing all cients requesting by IP to a "dead end." The clients accessing the site via ip it claimed were typically automated exploit tools and bots. Legitimate users type in the web address by it's domain question. With this context in mind, I don't really understand how DNS really works. I thought it worked by sending an IP back to a client for the requested DNS (like a phone book.) The client then uses the IP to access the site. The information above seems to indicate I misunderstand this. Can someone clarify this? (http://technet.microsoft.com/en-us/magazine/2005.01.hackerbasher.aspx)

  Read the article

• Apache ProxyPass/ProxyPassReverse to IIS

  - by Dana

  We have an ASP.NET web application which is mapped to a folder on an apache hosted php site using ProxyPass.ProxyPassReverse. A couple of problems being encountered. cookies are being lost which breaks the site navigation, this can be overcome by setting the asp app as cookieless. Forms authentication is used on the ASP site, this is also broken withe the proxypass in place, suspect this is cookie related also. ASP site works ok when run from a domain/ip address. Use of a separate domain / sub-domain is not an option duew to client requirements.

  Read the article

• How to suggest using an ORM instead of stored procedures?

  - by Wayne M

  I work at a company that only uses stored procedures for all data access, which makes it very annoying to keep our local databases in sync as every commit we have to run new procs. I have used some basic ORMs in the past and I find the experience much better and cleaner. I'd like to suggest to the development manager and rest of the team that we look into using an ORM Of some kind for future development (the rest of the team are only familiar with stored procedures and have never used anything else). The current architecture is .NET 3.5 written like .NET 1.1, with "god classes" that use a strange implementation of ActiveRecord and return untyped DataSets which are looped over in code-behind files - the classes work something like this: class Foo { public bool LoadFoo() { bool blnResult = false; if (this.FooID == 0) { throw new Exception("FooID must be set before calling this method."); } DataSet ds = // ... call to Sproc if (ds.Tables[0].Rows.Count > 0) { foo.FooName = ds.Tables[0].Rows[0]["FooName"].ToString(); // other properties set blnResult = true; } return blnResult; } } // Consumer Foo foo = new Foo(); foo.FooID = 1234; foo.LoadFoo(); // do stuff with foo... There is pretty much no application of any design patterns. There are no tests whatsoever (nobody else knows how to write unit tests, and testing is done through manually loading up the website and poking around). Looking through our database we have: 199 tables, 13 views, a whopping 926 stored procedures and 93 functions. About 30 or so tables are used for batch jobs or external things, the remainder are used in our core application. Is it even worth pursuing a different approach in this scenario? I'm talking about moving forward only since we aren't allowed to refactor the existing code since "it works" so we cannot change the existing classes to use an ORM, but I don't know how often we add brand new modules instead of adding to/fixing current modules so I'm not sure if an ORM is the right approach (too much invested in stored procedures and DataSets). If it is the right choice, how should I present the case for using one? Off the top of my head the only benefits I can think of is having cleaner code (although it might not be, since the current architecture isn't built with ORMs in mind so we would basically be jury-rigging ORMs on to future modules but the old ones would still be using the DataSets) and less hassle to have to remember what procedure scripts have been run and which need to be run, etc. but that's it, and I don't know how compelling an argument that would be. Maintainability is another concern but one that nobody except me seems to be concerned about.

  Read the article

• How to check if PAE is enabled? (Windows 7 32 bits)

  - by Altar

  How to tell for sure if PAE (Physical Address Extensions) is enabled or not? There is a SPECIFIC command I can use? I can read a registry value or something? (Windows 7 32 bits) I have found this on Internet but it doesn't answer my question: If your server has hot-add memory ability (ability to add more memory without shutting down the server !!) or data execution prevention (DEP) is enabled then PAE will be enabled automatically !! It only reformulate the question as "does my Qosmio x505 laptop support hot-add memory?"

  Read the article

• Problems with wired ethernet connection Ubuntu 11.10

  - by Andrew Fielden

  After some partition shuffling, I've got a problem on my 11.10 system. The wired ethernet interface fails to come up, although the wireless interface is working. I'm using NetworkManager. I thought this may be a problem with NetworkManager, so I checked the config files, which look ok. I then tried re-installing the package, but this didn't resolve the issues. I'm not sure at this point if the problem is due to software configuration, or a hardware problem. I've also tried the cable in other router ports, but same problem. The symptoms are:- System settings - Network reports that the cable is unplugged (it isn't) ifconfig reports the following eth0 Link encap:Ethernet HWaddr f0:4d:a2:a2:a7:fe UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:10 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:792 (792.0 B) TX bytes:0 (0.0 B) Interrupt:46 Base address:0xe000 My /etc/network/interfaces file has the following: auto lo iface lo inet loopback My /etc/resolv.conf file has the following: # Generated by NetworkManager The router's red light is on for this port dmesg reports ADDRCONF(NETDEV_UP): eth0: link is not ready

  Read the article

• How can I get the real Emailaddress of a recipient?

  - by Boas Enkler

  a user in out Company has 2 mail-addresses on one Exchange-Mailbox. e.g test@... and test1@... the Primary SMTP-address off the Mailbox is test@. If I send a message to test1@, load it using EWS and parse through the TORecipients-Collection there is exactly one emailadress. But the mailaddress EWS gives to me is test@... and not test1@... where I sent the mail. My problem is, that all mails sent to test@ should be imported in our CRM using my program. All mails sent to test1@... must not be imported. In real life both mailaddresses are from my Boss. One is used for normal purposes the other one is for confidential e.g. from his lawyer. Does anyone know how I can get the real-emailaddress the message was sent to?

  Read the article

• On VMWare Server, how can I specify which Ethernet port should be the one to be bridged?

  - by DrDavid

  My server has 4 ethernet ports; 1 uses a APIPA address to connect to a DroboElite (that's how they're designed to work), 1 is connected to the LAN, and the other two are unused currently. The issue is that VMWare Server seems to have an affinity to the port that's connected to the Drobo, which means that it can never reach the internet. If I disable the Drobo port, everything works just fine. If I enable the drobo port, nothing works (well, the drobo works, but the virtual machine doesn't ;) ) How can I tell VMWare Server to NOT use the drobo port when I'm bridging the connection?

  Read the article

• links for 2011-03-01

  - by Bob Rhubart

  Oracle Technology Network Architect Day: Denver - March 23 This live one-day event will bring together architects from a broad range of disciplines and domains to share insights and expertise in the use of Oracle technologies to meet the challenges today’s architects regularly face. (tags: oracle otn architect entarch) Java.net Reborn (Oracle Technology Network Blog (aka TechBlog)) "The migration was huge effort. Over 1400 projects were migrated (and some 30 projects are left to go). A large part of the migration was a big cleanup of abandoned projects...The new java.net site is smaller, faster and now the percentage of good, current content is much higher." (tags: oracle otn java java.net) This Week: OTN Java Developer Day in Boston, Massachusetts (US) | Java.net "This Thursday, March 3, the Oracle Technology Network will be hosting an OTN Developer Day titled You are the future of Java in Boston, Massachusetts (US). The all-day event includes a keynote address ("Java, the Language of the Future") and four separate tracks..." (tags: oracle otn java event) A brief introduction to BRM and architecture (Red Adventure) Yani Miguel offers a primer on the architecture behind Billing and Revenue Management. (tags: oracle otn brm) SOA Suite Integration: Part 1: Building a Web Service (The Shorten Spot) Anthony Shorten's first post in a new series "will not feature SOA Suite at all, but will concentrate on the capability for the Oracle Utilities Application Framework to create Web Services you can use for integration." (tags: oracle otn SOA soasuite) Darwin-IT: VirtualBox on Windows XP Martien van den Akker shares a few tips. (tags: oracle otn virtualization virtualbox) Pas Apicella: Developing RESTful Web Services from JDeveloper 11g (11.1.1.4) Plas says: "In this example we use JDeveloper to create a basic JAX-RS Web Service from support provided within the code editor as no wizard support exists within JDeveloper 11g at this stage." (tags: oracle otn REST SOA) Alexander Buckley: Maintenance Review of the Java VM Specification The Java Virtual Machine Specification is the authoritative reference for the design of the Java virtual machine that underpins the Java SE platform. In an implementation-independent manner, the Specification describes the architecture, linking model, and instruction set of the Java virtual machine, (tags: oracle otn java virtualization jvm javase)

  Read the article

• How to get wireless (Alfa) operate in full power and speed up wireless Internet?

  - by MahboobeAlam

  I am using Wireless to connect to the internet (router). My laptop has Atheros wireless (AR 242x/542x) adapter but the router is a little bit far-away from my room so I have to use an external wireless adapter i.e. Alfa (Realtek 8187) for connectivity. However, since I have started using Ubuntu I noticed that Alfa is not working in full power, internet speed in Ubuntu is much slower than in Windows on my laptop. When I am using Windows 7 the LED (bulb) on Alfa blinks as it should, but when in Ubuntu, it doesn't blink rather it is on but very dim. Connection using Atheros adapter is also the same (slow)... I have tried 4 methods (I found on the Internet) to troubleshoot this matter but no success. It seems to me that Ubuntu/Linux is not letting these wireless adapters to operate in full strength. iwconfig shows that power management is off for both. So what's the problem? Details: ifconfig eth0 Link encap:Ethernet HWaddr 00:1f:16:1e:36:ec UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) Interrupt:45 Base address:0x6000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:1657 errors:0 dropped:0 overruns:0 frame:0 TX packets:1657 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:241697 (241.6 KB) TX bytes:241697 (241.6 KB) wlan0 Link encap:Ethernet HWaddr 00:22:5f:9b:24:b5 inet6 addr: fe80::222:5fff:fe9b:24b5/64 Scope:Link UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:715460 errors:0 dropped:0 overruns:0 frame:0 TX packets:694246 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:493539292 (493.5 MB) TX bytes:235159393 (235.1 MB) wlan1 Link encap:Ethernet HWaddr 00:c0:ca:42:14:62 inet addr:192.168.100.102 Bcast:192.168.100.255 Mask:255.255.255.0 inet6 addr: fe80::2c0:caff:fe42:1462/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:171053 errors:0 dropped:0 overruns:0 frame:0 TX packets:181363 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:74094659 (74.0 MB) TX bytes:59474204 (59.4 MB) iwconfig lo no wireless extensions. eth0 no wireless extensions. wlan0 IEEE 802.11bg ESSID:off/any Mode:Managed Access Point: Not-Associated Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off wlan1 IEEE 802.11bg ESSID:"Zia" Mode:Managed Frequency:2.412 GHz Access Point: 00:0D:F0:9C:A6:18 Bit Rate=54 Mb/s Tx-Power=20 dBm Retry long limit:7 RTS thr:off Fragment thr:off Power Management:off Link Quality=70/70 Signal level=-31 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:204 Invalid misc:6610 Missed beacon:0

  Read the article

• Cannot ping any computers on LAN

  - by Timothy

  I havem't been able to find a straight forward answer on this yet. I'm hoping people here are able to help! Keep in mind that I'm a complete beginner at this - this is the first installation i've done for any LINUX systems ever so please keep that in mind when answering this question. We are a complete Windows shop, using nothing but Microsoft products but looking into the value of OpenStalk however have been having problems getting Ubuntu Server installed and speaking to the network. The machine is getting an IP address which is telling me that some sort of DHCP activity is working but I'm not able to ping any computer on our network as well as not able to connect to the internet. Every time I try to ping i'm getting; Destination Host Unreachable I've tried using modifying the resolv.conf file with our static details to match my Windows 7 machine still with no luck. Even tried disabling the firewall on Ubuntu Server 11 and no luck. Any ideas? Please let me know if there is any information you need from the server and I'll post up.

  Read the article

< Previous Page | 597 598 599 600 601 602 603 604 605 606 607 608  | Next Page >