Search Results

Search found 17267 results on 691 pages for 'dynamic ip'.

Page 607/691 | < Previous Page | 603 604 605 606 607 608 609 610 611 612 613 614  | Next Page >

• Webmin ADSL module

  - by expatcm

  I was wondering if the Webmin ADSL module is going to help me solve a problem .... but I cannot find any documentation telling me what the module does ..... Any ideas? What I am hoping is that it will solve a problem .... I am just in the process of setting up a Debian server. I will use the DHCP server as part of the Debian setup to manage the lan IP addresses. I want to turn off the external DHCP server which is part of the Linksys ADSL modem / router and use just the modem. The challenge I have is knowing what I need to do in order to get the public DNS on the eth1. When I turn off the DHCP on the modem / router not a lot happens apart from no longer being able to access the settings .......... So I am looking at this Webmin module and wondering if it is to manage the ADSL connection and find the public DNS address .... The local DHCP server is working well for the lan, I am just stuck for the external DNS.

  Read the article

• Cannot connect to Solaris Server when Oracle GoldenGate process uses the port

  - by Abdallah Ghrb

  I'm trying to test the Oracle goldengate to replicate data between two databases on the same server. So I installed two databases and two goldengate homes in the same machine. The goldengate processes are started from each home and they are responsible for the replication : Process from home 1 configured on port 7809 & process for home 2 configured on port 7810. For a successful replication, processes started from goldengate home 1 should communicate with processes started from goldengate home 2. But for some reasons, this is not happening. The goldengate log file has the following error : OGG-01223 Oracle GoldenGate Capture for Oracle, exthrr.prm: TCP/IP error 131 (Connection reset by peer). "Googling" for this error, it said that the connection occurred but the host terminated it. Tried to telnet the machine with the used port and it gave the following error: bash-3.00$ telnet 10.10.3.124 7810 Trying 10.10.3.124... Connected to 10.10.3.124. Escape character is '^]'. Connection to 10.10.3.124 closed by foreign host. Here the communication occurs but for only around 3 seconds then it is closed by the host, which is the same explanation of the above error in the goldengate log file. I tried to change the port but still the same error. The problem is happening only when the goldengate process is using the port. When other process is using the same port, I can telnet successfully.

  Read the article

• Very slow connection to xserve via afp or smb

  - by Mhoffman13

  Help. File transfer and connection speed to our Xserve are painfully slow from newly purchased iMacs. The Xserve is only used as a file server, its running 10.4.11. The problem seems to be only happening on brand new iMacs running 10.6.3. When connected either over afp or smb copying files is many times slower than usual. Other machines on the network running either 10.4 or 10.5 have a normal connection speed. To try to rule out OS incompatibility I connected the new iMac running 10.6 to another computer running 10.4 over the network. The file transfer speed was fast as normal. So it seems the problems lies with the X serve (maybe). The afp logs either access or error don't show anything unusual. One thing that did look different was when the imac was connected to the Xserve the user had its id listed as its IP address. The other machines connected, had the id of broadcasthost. I also noticed that when connected from the new iMac I can only see one of the mirrors. When any other computer connects both mirrors are shown. Tried a restart of the Xserve but the problem persists. Thanks in advance for any advice

  Read the article

• DNS-Based Environment Determination

  - by zvolkov

  Found the following here. The questions is: where can I find more details on how exactly implement this on Windows? Any guide or how-to anybody? Or maybe you can provide your invaluable suggestions? Specifically, how do I make so that "all QA servers would first resolve entries in qa.example.com first and then if that lookup failed they would try example.com" (I'm a dev, not a DNS specialist, but our IT Support has refused to help on this:() Use DNS Based Environment Determination for your servers. Do this by initially splitting your top level domain into a number of sub domains depending on their function, and then creating DNS Service Names in each of the sub domains pointing to the relevant server for that service. Based on the list above we would then have: * clientdb.prod.example.com for Production * clientdb.perf.example.com for Performance Testing * clientdb.qa.example.com for QA * clientdb.dev.example.com for Development Servers then resolve entries in their relevant sub domain by function. That is, all QA servers would first resolve entries in qa.example.com first and then if that lookup failed they would try example.com. This allows you to have a single configuration entry for your client database hostname (clientdb) that would resolve correctly in all environments. This technique has the added advantage of still having global services defined in a common top level domain. This seems to be related to Providing "split horizon" DNS service. Reading that, I see that I will probably need separate DNS Server for each environment. Is this true or does Windows support some form of "tagging" the records to be visible depending on the requestor's IP?

  Read the article

• What's wrong with my VirtualHost?

  - by johnlai2004

  I have the following VirtualHost // filename: /etc/apache2/sites-available/ccbbbcc <VirtualHost 1.1.1.1:80> ServerAdmin [email protected] ServerName ccbbbcc.com ServerAlias www.ccbbbcc.com DocumentRoot /srv/www/ccbbbcc/production/public_html/ ErrorLog /srv/www/ccbbbcc/production/logs/error.log CustomLog /srv/www/ccbbbcc/production/logs/access.log combined </VirtualHost> And then I also have //filename: /etc/apache2/sites-available/default <VirtualHost 1.1.1.1:80> ServerAdmin webmaster@localhost DocumentRoot /var/www/ <Directory /> Options FollowSymLinks AllowOverride None </Directory> blah blah blah How come when I type into my browser http://1.1.1.1, it takes me to http://ccbbbcc.com ? Even when I point new urls to the IP 1.1.1.1, webpages serve from http://ccbbbcc.com. Why is the ccbbbcc.com overriding all my other virtual hosts? Why am I unable to serve pages from /var/www directory? I've made sure to use a2ensite and to restart apache. This is what my /etc/apache2/ports.conf looks like NameVirtualHost 1.1.1.1:80 Listen 80 Listen 443

  Read the article

• Run command remotely on Windows computer from C#

  - by Bilal Aslam

  I have a Windows Server 2008 instance on Amazon EC2 (Amazon's cloud compute platform, which provides VMs in the cloud). It has an external IP, and I have an admin account on the box. I would like to 'bootstrap' this instance remotely i.e. I want to run commands to download, install and configure apps on it, all without having to log on even once. Also, I cannot use psexec on the source computer. I have figured out how to do this to a remote, domain-joined computer using WMI. However, I have NOT been able to do for a remote computer on EC2. Here are some specific restrictions: 1) The remote computer is not part of my domain, hence no Kerberos 2) The remote computer does not have a cert I trust, or vice versa I am sure I am running into to some auth/trust restriction. Is there any way I can run a single command on the remote, given that I have admin privileges? I'm not tied down to using WMI, but I do need to run a command somehow. Feels like this should be a solved problem.

  Read the article

• LYNC / OCS... problems getting edge server working.

  - by TomTom

  New setup Lync 2010 (i.e. OCS 2010). I have serious problems getting my edge system going. Internally things work fine. Externally I am stuck. I have used the tester at https://www.testocsconnectivity.com/ and it also fails. NOTE: I use the domain xample.com / xample.local here just as example. Here is the setup. I have 2 internal hosts (lync.xample.local, edge.xample.local). edge.xample.com is also correctly in dns. and points to the edge.xample.local external assigned ip address (external interface). Externally, I have the following dns entries: edge.xample.com _sip._tcp - edge.xample.com 443 _sipfederationtls._tcp - edge.xample.com 5061 _sipinternaltls._tcp - lync.xample.local 5061 _sip._tls - edge.xample.com 443 My problem is that the ocs connection test always ends up trying to contact lync.xample.local (i.e. the internal address) when connecting to [email protected]. The error is: Attempting to Resolve the host name lync.xample.local in DNS. This shows me it clearly manages to connect to SOMETHING, but it does either fall through to the _sipinternaltls._tcp entry, OR it does get that internal entry wrongly from the edge system. Am I missing some entries or have some wrong?

  Read the article

• Karmic iptables missing kernel moduyles on OpenVZ container

  - by luison

  After an unsuccessful p2v migration of my Ubuntu server to an OpenVZ container which I am stack with I thought I would give a try to a reinstall based on a clean OpenVZ template for Ubuntu 9.10 (from the OpenVZ wiki) When I try to load my iptables rules on the VM machine I've been getting errors which I believe are related to kernel modules not being loaded on the VM from the /vz/XXX.conf template model. I've been testing with a few post I've found but I was stack with the error: WARNING: Deprecated config file /etc/modprobe.conf, all config files belong into /etc/modprobe.d/. FATAL: Could not load /lib/modules/2.6.24-10-pve/modules.dep: No such file or directory iptables-restore v1.4.4: iptables-restore: unable to initialize table 'raw' Error occurred at line: 2 Try `iptables-restore -h' or 'iptables-restore --help' for more information. I read about the template not loading all iptables modules so I added modules to the XXX.conf of the VZ virtual machine like this: IPTABLES="ip_tables iptable_filter iptable_mangle ipt_limit ipt_multiport ipt_tos ipt_TOS ipt_REJECT ipt_TCPMSS ipt_tcpmss ipt_ttl ipt_LOG ipt_length ip_conntrack ip_conntrack_ftp ip_conntrack_irc ipt_conntrack ipt_state ipt_helper iptable_nat ip_nat_ftp ip_nat_irc" As the error remained I read that I should build dependencies again on the virtual machine: depmod -a but this returned an error: WARNING: Couldn't open directory /lib/modules/2.6.24-10-pve: No such file or directory FATAL: Could not open /lib/modules/2.6.24-10-pve/modules.dep.temp for writing: No such file or directory So I read again about creating the directory empty and redoing "depmod -a" it. I now don't get the dependancies error but get this and I don't have a clue how to proceed: WARNING: Deprecated config file /etc/modprobe.conf, all config files belong into /etc/modprobe.d/. FATAL: Module ip_tables not found. iptables-restore v1.4.4: iptables-restore: unable to initialize table 'raw' Error occurred at line: 2 Try `iptables-restore -h' or 'iptables-restore --help' for more information. I understand that iptables rules have to be different on the VM machine and perhaps some of the rules we are trying to apply (from our physical server) are not compatible but these are just source IP and destination port checks that I would like to be able to have available . I've heard that on the CentOS template there are no issues with this, so I understand is to do with VM config. Any help would be greatly appreciated.

  Read the article

• Debian DNSSEC - howto secure a domain?

  - by Daniel Marschall

  I have a beginner question about DNSSEC. I have much experience with TLS and cryptography-stuff and would like to try out this new technology. I have googled very much about this but I haven't found useful information for me. I think one confusion in information gathering is that "Debian howto DNSSEC setup" can mean "How to USE DNSSEC for resolving" OR "How to secure your domain with DNSSEC". I am searching the second. I am running a Debian Squeeze server with root privileges which has a domain name ending with ".de" (which is already signed by the root zone). The network interface at this server uses the gateway IP (DNS resolver?) of the datacentre the server is running on. My domain is hosted at freedns.afraid.org , where I can add DNS RRs for my domain. They are currently NOT capable of adding DNSSEC RRs, but I am bugging them to support this soon. ;-) My simple question is: How do I setup DNSSEC on Debian? Resp. who have I ask to? As far as I understand, all I have to do is to run dnssec-keygen on my Debian server and then add the key to my DNS-provider as DNSSEC RR. (And change it every 30 days?) I have looked at this http://www.isc.org/files/DNSSEC_in_6_minutes.pdf but it looks like you have to be the owner of a ZONE, so I don't think this applies to me. Who needs to sign my domain? My DNS-provider or my zone (DeNIC) or can I do it myself? Any help is very appreciated!

  Read the article

• how to define service runlevel order position?

  - by DmitrySemenov

  I setup bind-dlz and need mysql start prior NAMED when system starts here is what I have [root@semenov]# ./test.sh mysql 0:off 1:off 2:on 3:on 4:on 5:on 6:off named 0:off 1:off 2:off 3:on 4:on 5:on 6:off lrwxrwxrwx. 1 root root 15 Apr 15 18:57 /etc/rc3.d/S93mysql -> ../init.d/mysql lrwxrwxrwx. 1 root root 15 Apr 15 18:57 /etc/rc3.d/S90named -> ../init.d/named here is what I have in mysql init script # Comments to support chkconfig on RedHat Linux # chkconfig: 2345 84 16 # description: A very fast and reliable SQL database engine. # Comments to support LSB init script conventions ### BEGIN INIT INFO # Provides: mysql # Required-Start: $local_fs $network $remote_fs # Should-Start: ypbind nscd ldap ntpd xntpd # Required-Stop: $local_fs $network $remote_fs # Default-Start: 2 3 4 5 # Default-Stop: 0 1 6 # Short-Description: start and stop MySQL # Description: MySQL is a very fast and reliable SQL database engine. ### END INIT INFO so when I remove named from chkconfig and have there just mysql, it starts with order number 84: /etc/rc3.d/S84mysql - ../init.d/mysql but when I add named inside chkconfig it's order changes to 93: /etc/rc3.d/S93mysql - ../init.d/mysql as a result mysql will be starting after named and named will fail (no sql available) any ideas what I'm doing wrong? here is what I have in named init script # chkconfig: 345 90 16 # description: named (BIND) is a Domain Name Server (DNS) \ # that is used to resolve host names to IP addresses. # probe: true ### BEGIN INIT INFO # Provides: $named # Required-Start: $local_fs $network $syslog # Required-Stop: $local_fs $network $syslog # Default-Start:2 3 4 # Default-Stop: 0 1 2 3 4 5 6 # Short-Description: start|stop|status|restart|try-restart|reload|force-reload DNS server # Description: control ISC BIND implementation of DNS server ### END INIT INFO thanks, Dmitry

  Read the article

• BIND9 server types

  - by aGr

  I was configuring DNS on my server using BIND9, everything seems to work, but I have a question regarding my config file. I've ended up with this configuration in /etc/bind/named.conf.local zone "example.com" { type master; file "/etc/bind/db.example.com"; allow-transfer { 192.168.1.1; }; }; zone "1.168.192.in-addr.arpa" { type master; notify no; file "/etc/bind/db.192"; allow-transfer { 192.168.1.1; }; }; forwarders { 10.253.22.140; 10.253.22.141; }; I've read about the different type of dns server, like primary master etc. The first two parts (zone and zone) corresponds to primary dns server configuration. First record for "classic" lookup, second one for reverse. The last part (forwarders) is configuration of cache-server and contains the ISP's IP of DNS server. So all names resolved thanks to this server will be cached. Simple question: am I right? Does my description make sense? Or one server can be only either master or either cached?

  Read the article

• Get Illegal Instruction error when booting Linux in VirtualBox, works fine when booted directly

  - by rkjnsn

  I have a computer on which I am dual booting Windows 7 and Gentoo Linux (both 64-bit). I want to be able to load up my Linux installation in a VM while I am booted into Windows. I have installed VirtualBox and followed the instructions for creating a raw disk VMDK. When I start the VM, Linux starts booting, but then fails with the following error when unlocking my root partition: truecrypt[441] trap invalid opcode ip:373615538e0 sp:3dd0e0dfb60 error:0 in libpixman-1.so.0[373614d6000+8d000] Everything works fine when I boot into Linux directly. What could cause an illegal instruction to be hit in libpixman only when booting in VirtualBox? Update: As a troubleshooting step, I recompiled pixman without "-march", and no longer get an illegal instruction error in that library. (The boot fails in the same spot with the same error in a different library, however.) How can I determine the specific opcode that isn't working in VirtualBox so I can disable it in my CFLAGS without having to disable all CPU-specific optimizations? I am still confused as to why there would be any user-mode instruction that would fail to work in a VM. Is this a known limitation? My CPU is an Intel Core i7 3720QM, and I have hardware virtualization support enabled.

  Read the article

• Prevent outgoing traffic unless OpenVPN connection is active using pf.conf on Mac OS X

  - by Nick

  I've been able to deny all connections to external networks unless my OpenVPN connection is active using pf.conf. However, I lose Wi-Fi connectivity if the connection is broken by closing and opening the laptop lid or toggling Wi-Fi off and on again. I'm on Mac OS 10.8.1. I connect to the Web via Wi-Fi (from varying locations, including Internet cafés). The OpenVPN connection is set up with Viscosity. I have the following packet filter rules set up in /etc/pf.conf # Deny all packets unless they pass through the OpenVPN connection wifi=en1 vpn=tun0 block all set skip on lo pass on $wifi proto udp to [OpenVPN server IP address] port 443 pass on $vpn I start the packet filter service with sudo pfctl -e and load the new rules with sudo pfctl -f /etc/pf.conf. I have also edited /System/Library/LaunchDaemons/com.apple.pfctl.plist and changed the line <string>-f</string> to read <string>-ef</string> so that the packet filter launches at system startup. This all seems to works great at first: applications can only connect to the web if the OpenVPN connection is active, so I'm never leaking data over an insecure connection. But, if I close and reopen my laptop lid or turn Wi-Fi off and on again, the Wi-Fi connection is lost, and I see an exclamation mark in the Wi-Fi icon in the status bar. Clicking the Wi-Fi icon shows an "Alert: No Internet connection" message: To regain the connection, I have to disconnect and reconnect Wi-Fi, sometimes five or six times, before the "Alert: No Internet connection" message disappears and I'm able to open the VPN connection again. Other times, the Wi-Fi alert disappears of its own accord, the exclamation mark clears, and I'm able to connect again. Either way, it can take five minutes or more to get a connection again, which can be frustrating. Why does Wi-Fi report "No internet connection" after losing connectivity, and how can I diagnose this issue and fix it?

  Read the article

• Internet doesn't work when enable local Lan

  - by rakesh yadav

  We have the following network setup: A) Router IP 192.168.51.49 B) Windows Server 2008 R2 with dual NIC: B1) WAN interface (192.168.0.2) ( Used for internet) B2) LAN interface (192.168.1.2) ( used for local connectivity) when i keep both LAN Enabled than my internet doesn't work, but if I disabled my local Lan than internet working fine. so please help me how can resolved this issue or should i need to do routing on my server Please find the below attached route print result C:\Users\Administrator>route print =========================================================================== IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.51.49 192.168.51.50 276 0.0.0.0 0.0.0.0 192.168.30.227 192.168.30.228 266 192.168.30.224 255.255.255.240 On-link 192.168.30.228 266 192.168.30.228 255.255.255.255 On-link 192.168.30.228 266 192.168.30.239 255.255.255.255 On-link 192.168.30.228 266 192.168.51.48 255.255.255.240 On-link 192.168.51.50 276 192.168.51.50 255.255.255.255 On-link 192.168.51.50 276 192.168.51.63 255.255.255.255 On-link 192.168.51.50 276 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 202.56.230.5 255.255.255.255 192.168.51.49 192.168.51.50 21 202.56.230.6 255.255.255.255 192.168.51.49 192.168.51.50 21 192.168.26.124 255.255.255.255 192.168.51.49 192.168.51.50 21 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.51.50 276 224.0.0.0 240.0.0.0 On-link 192.168.30.228 266 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.51.50 276 255.255.255.255 255.255.255.255 On-link 192.168.30.228 266 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 192.168.30.227 Default 0.0.0.0 0.0.0.0 192.168.51.49 Default ===========================================================================

  Read the article

• Strange IIS hits originating from Trend Micro

  - by TesterTurnedDeveloper

  I'm trying to trace thru an error on a extranet site I maintain. I've had a look thru the logs, and I'm seeing hits originate from these IP addresses: 216.104.15.130 216.104.15.138 216.104.15.142 216.104.15.13 150.70.84.49 150.70.84.44 Network-tools.com gives 'TREND MICRO INCORPORATED' as the owner of all these IPs. The hits fail as they aren't sending any cookies (therefore aren't considered logged in). The hits are to pages containing URLs that only the logged in user would see, i.e. ImageEdit.aspx?ImageId=467424. I.e. the server isn't guessing these URLs, someone would have to log into the site to know these URLs exist. Theory: the Trend Antivirus client grabs URLs and sends them to the server for 'extra processing'? Googling around gives me this: http://www.forumpostersunion.com/showthread.php?p=51272 - where people are reporting comment spam from these addresses. The articles says their servers have been hacked (a few months ago, presumably fixed now?). A hacked server wouldn't explain how the URLs have been plucked off the user's PCs. Has anyone seen this before? Anything nefarious going on here?

  Read the article

• How to get a new-pssession in PowerShell to talk to my ICS-connected laptop for Remoting

  - by Scott Bilas

  If I have my laptop on the LAN, then Powershell remoting works fine from my workstation to the laptop. However, the LAN is wireless, and so sometimes I will connect on a wire to my workstation. It has two ethernet ports so I have the secondary wired up to share to the laptop using Win7's Internet Connection Sharing. (Btw I know that avoiding ICS would solve the problem, but that's not an option right now.) So my question is: what magic registry bits or command line options do I need to flip to get remoting to work to my laptop through ICS? Here's what happens when I try it: new-pssession -computername 192.168.137.161 [192.168.137.161] Connecting to remote server failed with the following error message : The WinRM client cannot process the request. Default authentication may be used with an IP address under the following conditions: the transport is HTTPS or the destination is in the TrustedHosts list, and explicit credentials are provided. Use winrm.cmd to configure TrustedHosts. Note that computers in the TrustedHosts list might not be authenticated. For more information on how to set TrustedHosts run the following command: winrm help config. For more information, see the about_Remote_Troubleshooting Help topic. + CategoryInfo : OpenError: (System.Manageme....RemoteRunspace:RemoteRunspace) [], PSRemotingTransportException + FullyQualifiedErrorId : PSSessionOpenFailed I'm having a hard time understanding the documentation for PowerShell and WinRM. I've tried messing with allowing ports in the firewall and setting TrustedHosts to * on my workstation (don't think this is a good idea on the laptop). I have no idea where to go from here, would appreciate any help.

  Read the article

• can't backup to a NAS drive as offline schedule task

  - by imageng

  I have seen this problem issue discussed in several forums including this one, but could not find a solution. On MS server 2003 I configured a Backup task, the target backup is on a NAS disc (Seagate BlackArmor NAS 110). The backup task is working well as a scheduled task or by a direct command, when I am logged on. It is not working when the user is offline (in this case - Administrator). I already tried the following actions: 1) addressing to the target as network drive (Y:location..), 2)Using UNC instead, 3) making the drive a domain member (the NAS admin S/W allows to define itself as a domain member) The result log message for 1 and 2 is: "The operation was not performed because the specified media cannot be found." The result log message for 3 is empty file. The schedule task "RUN" command is: C:\WINDOWS\system32\ntbackup.exe backup "@C:\Documents and Settings\Administrator\Local Settings\Application Data\Microsoft\Windows NT\NTBackup\data\de-board.bks" /a /d "Set created 2/14/2010 at 5:10 PM" /v:yes /r:no /rs:no /hc:off /m incremental /j "de-board" /l:s /f "\10.0.0.8\public\Backups\IBMServer\de-board.bkf" 10.0.0.8 is the static IP of the NAS. "Run only if logged on" is NOT marked. Password of the administrator user is set. It is obvious that there is no access to the NAS when the user is logged-out. Do you have any idea how can I solve it? Thanks

  Read the article

• How do I boot [embedded] linux from sd card?

  - by Brandon Yates

  I am hacking together a quick embedded linux system on a DM816x evm board. Previously I have been using TFTP and NFS to load my kernel and root filesystem to the board. I am now trying to switch over to loading everything from an SD card. I have my card partitioned such that uBoot and my kernel image are in one partition, and my rootFS in another partition. At power-on, Uboot starts correctly and successfully launches the kernel. However, the kernel is unable to mount the root file system. It appears that it doesn't recognize any SD (mmc) cards. It gives this error message. VFS: Cannot open root device "mmcblk0p2" or unknown-block(2,0) Please append a correct "root=" boot option; here are the available partitions: 1f00 256 mtdblock0 (driver?) 1f01 8 mtdblock1 (driver?) 1f02 2560 mtdblock2 (driver?) 1f03 1272 mtdblock3 (driver?) 1f04 2432 mtdblock4 (driver?) 1f05 128 mtdblock5 (driver?) 1f06 4352 mtdblock6 (driver?) 1f07 204928 mtdblock7 (driver?) 1f08 50304 mtdblock8 (driver?) Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(2,0) I feel like I'm missing something fundamental here. Why does it not recognize the root device I am trying to load from? Here is my uBoot boot script that is running: setenv bootargs console=ttyO2,115200n8 root=/dev/mmcblk0p2 rw mem=124M earlyprink vram=50M ti816xfb.vram=0:16M,1:16M,2:6M ip=off noinitrd;mmc init;fatload mmc 1 0x80009000 uImage;bootm 0x80009000

  Read the article

• Unable to Access Certain Websites

  - by codejoust

  Through a local network, all computers except one ubuntu machine can access 1. Adobe.com 2. Icann.org 3. Apache.org 4. Example.com. The ubuntu machine returns (in firefox): "Though the site seems valid, the browser was unable to establish a connection." Furthermore, when I traceroute those websites using the ubuntu machine, they all return ubuntu.local, and it ends there: (traceroute to icann.org (192.0.32.7), 30 hops max, 40 byte packets 1 ubuntu.local (192.168.1.105) 3000.791 ms !H 3000.808 ms !H 3000.814 ms !H I've checked the hosts file, and there isn't anything in there, and I have an apache server there so if it was redirected to localhost, I'd probably see the localhost webroot page. Thanks in advance! user@ubuntu:~$ netstat -nr Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 192.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth1 The Ubuntu Machine is one of six on the network. I'm using opendns for dns, so I do think that should be a problem.

  Read the article

• Break all hardlinks within a folder

  - by Georges Dupéron

  I have a folder which contains a certain number of files which have hard links (in the same folder or somewhere else), and I want to de-hardlink these files, so they become independant, and changes to their contents won't affect any other file (their link count becomes 1). Below, I give a solution which basically copies each hard link to another location, then move it back in place. However this method seems rather crude and error-prone, so I'd like to know if there is some command which will de-hardlink a file for me. Crude answer : Find files which have hard links (Edit: To also find sockets, etc. that have hardlinks, use find -not -type d -links +1) : find -type f -links +1 A crude method to de-hardlink a file (copy it to another location, and move it back) : Edit: As Celada said, it's best to do a cp -p below, to avoid loosing timestamps and permissions. Edit: Create a temporary directory and copy to a file under it, instead of overwriting a temp file, it minimizes the risk to overwrite some data, though the mv command is still risky (thanks @Tobu). # This is unhardlink.sh set -e for i in "$@"; do temp="$(mktemp -d ./hardlnk-XXXXXXXX)" [ -e "$temp" ] && cp -ip "$i" "$temp/tempcopy" && mv "$temp/tempcopy" "$i" && rmdir "$temp" done So, to un-hardlink all hard links (Edit: changed -type f to -not -type d, see above) : find -not -type d -links +1 -print0 | xargs -0 unhardlink.sh

  Read the article

• Using Varnish (only) for DDoS mitigation

  - by Martin Kanters

  My VPS is suffering from a (D)DoS doing a SYN flood with spoofed IPs. I'm right now searching from ways how to be able to defend (at least a bit) against it. It's running a DirectAdmin apache2 webserver. Mainly used for serving PHP and MySQL. We are using CloudFlare, which are saying that they are able to mitigate (D)DoS at some level, now the attacker knows our real IP address, so CloudFlare isn't helping a bit. I've done some searching on the net and found out about enabling SYN cookies, to defend against it. I've checked my settings and it seems it was enabled all along. I've also read about that Varnish is able to defend against SYN flooding and Slowloris attacks, now I'm pretty interested in using that. The thing is that CloudFlare is already caching a lot from us, and I don't wish to spend too much resources on Varnish. Is it possible and smart to set up Varnish only for the better handling of requests? Are there perhaps better ways which I've missed? Thanks in advance, Martin

  Read the article

• Deciphering an IIS6 Httperr log file

  - by smackaysmith

  We have a Windows 2003 R2 SP2 server with iis6 that is creating a 1024kb httperr file every minute. I can't figure out what I'm looking at. Here's a snippet: 2010-03-24 13:15:05 10.53.2.35 1667 10.53.2.12 80 HTTP/1.1 PUT /hserver.dll?&V01|&IMAC=0080646077AB|CID=32|CN=LWT0080646077AB|ED=1|IP=10.53.2.35|SM=255.255.255.0|GW=10.53.2.1|SN=10.53.2.255|DM=logs.com|1D=10.53.2.12|2D=10.101.2.12|0D=1|AL=/usr/sbin/netxserv|AV=4.1.0.0|CP=VIAüEstherüprocessorüü800MHz|CPS=800|RM=190512|B1=1.18|PD2=1024x768x16ü@ü60Hz|IM=6.6.2-02|CI=3600|SN#=6KHDG301300|OS=23|VI=1|P1=24|TZO=-301|TZ=CDT|FS=128|MD=2003-04|CO=|LO=|AP0=BaseüSystem|NA|6.6.2-02|AP1=RapportüAgent|NA|4.1.0-3.26|AP2=TrueType|NA|6.8.0-3.4|AP3=WebFonts|NA|2.0.4-3.6|AP4=TrueTypeüFonts|NA|6.8.0-3.5|AP5=Network_login|NA|1.0.0-1.0.3|AP6=ScreenüSaver|NA|3.13|AP7=DMonitor|NA|1.0.0-0.4.0|AP8=MozillaüFirefox_15|NA|1.5.0.8-3.6|AP9=RemoteüShadow|NA|3.17|AP10=RemoteüDesktop|NA|1.6.0-1.0|AP11=SNMP|NA|5.1.3.1-3.13|AP12=LinuxüPrinting|NA|3.8.27-3.33|AP13=SSH|NA|3.8.1-3.25|AP14=ThinPrint|NA|6.2.87-0.2|AP15=XDMCP|NA|6.8.0-3.29|AP16=Ericom|NA|8.2.0-3.29|AP17=Daylightüsavingütimeüupdate|NA|1.1.0-1.0.0| 411 - LengthRequired - What on earth am I looking at? Nothing in the system or app logs. Finally, in iis manager, Default Web Site label has boxes instead of spaces. Very odd.

  Read the article

• Xen Windows Guest spawn doesn't spawn a vnc display

  - by Henrik P. Hessel

  I'm using this HVM File to create a new guest kernel = "/usr/lib/xen-3.2-1/boot/hvmloader" builder='hvm' memory = 4096 # Should be at least 2KB per MB of domain memory, plus a few MB per vcpu. shadow_memory = 64 name = "hessel-windows2008" vif = [ 'ip=188.40.xx.xx,mac=00:16:3E:C1:8F:CE' ] acpi = 1 apic = 1 disk = [ 'file:/home/xen/disks/hessel/win2008/win2008.img,hda,w', 'file:/home/xen/isopool/win2008_32.iso,hdc:cdrom,r' ] device_model = '/usr/lib/xen/bin/qemu-dm' #----------------------------------------------------------------------------- # boot on floppy (a), hard disk (c) or CD-ROM (d) # default: hard disk, cd-rom, floppy boot="dc" sdl=0 vnc=1 vncdisplay=1 vnclisten="0.0.0.0" vncconsole=1 vncpasswd='howtoforge' stdvga=0 serial='pty' usbdevice='tablet' The guest is created without an error. But no vnc display is created. Any ideas, how to fix that? prometheus:~# netstat -ant Active Internet connections (servers and established) Proto Recv-Q Send-Q Local Address Foreign Address State tcp 0 0 127.0.0.1:615 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:111 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:8080 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:53 0.0.0.0:* LISTEN tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN tcp 0 0 127.0.0.1:6010 0.0.0.0:* LISTEN tcp 0 232 188.40.xx.xx:8080 195.36.75.26:54032 ESTABLISHED tcp 0 0 188.40.xx.xx:8080 195.36.75.26:53085 ESTABLISHED tcp6 0 0 :::8080 :::* LISTEN tcp6 0 0 :::53 :::* LISTEN tcp6 0 0 :::22 :::* LISTEN tcp6 0 0 ::1:6010 :::* LISTEN

  Read the article

• Can't ping through default gateway

  - by Andrew G.H.

  I have the following configuration: Routing table on M3 is: Destination Gateway Genmask Flags MSS Window irtt Iface 0.0.0.0 192.168.2.1 0.0.0.0 UG 0 0 0 eth1 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 192.168.3.0 0.0.0.0 255.255.255.192 U 0 0 0 eth0 Routing table on M1 is: Destination Gateway Genmask Flags MSS Window irtt Iface 0.0.0.0 192.168.0.1 0.0.0.0 UG 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 192.168.0.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 So basically M3's gateway is M1, and M1's gateway is M2's wireless internet interface. If I ping 8.8.8.8 from M1, everything is ok, replies are received. Pinging from M1 to M3 and viceversa is also possible. I have configured M1 as gateway trafic forwarder using firestarter package and stopped firewall with it. iptables policies are ACCEPT for everything. Problem: I have tried ping-ing ip 8.8.8.8 from M3 but without success. What could be the source of this problem?

  Read the article

• Setting up MongoDB in High Performance Computing LSF linux cluster

  - by Dnaiel

  I am trying to run mongo in a LSF cluster computing environment where I have no admin control. Our sysadmin installed mongodb, but it is not running. Any ideas on what should I ask the server admin to do for it to run? Or if I could run it locally? [node1382]allelix> mongod --dbpath /users/dnaiel/ma/mongodb/ Tue Oct 2 21:33:48 [initandlisten] MongoDB starting : pid=22436 port=27017 dbpath=/seq/epigenome01/allelix/ma/mongodb/ 64-bit host=node1382 Tue Oct 2 21:33:48 [initandlisten] Tue Oct 2 21:33:48 [initandlisten] ** WARNING: You are running on a NUMA machine. Tue Oct 2 21:33:48 [initandlisten] ** We suggest launching mongod like this to avoid performance problems: Tue Oct 2 21:33:48 [initandlisten] ** numactl --interleave=all mongod [other options] Tue Oct 2 21:33:48 [initandlisten] Tue Oct 2 21:33:48 [initandlisten] db version v2.2.0, pdfile version 4.5 Tue Oct 2 21:33:48 [initandlisten] git version: f5e83eae9cfbec7fb7a071321928f00d1b0c5207 Tue Oct 2 21:33:48 [initandlisten] build info: Linux ip-10-2-29-40 2.6.21.7-2.ec2.v1.2.fc8xen #1 SMP Fri Nov 20 17:48:28 EST 2009 x86_64 BOOST_LIB_VERSION=1_49 Tue Oct 2 21:33:48 [initandlisten] options: { dbpath: "/users/dnaiel/ma/mongodb/" } Tue Oct 2 21:33:48 [initandlisten] journal dir=users/dnaiel/ma/mongodb/journal Tue Oct 2 21:33:48 [initandlisten] recover begin Tue Oct 2 21:33:48 [initandlisten] info no lsn file in journal/ directory Tue Oct 2 21:33:48 [initandlisten] recover lsn: 0 Tue Oct 2 21:33:48 [initandlisten] recover /seq/epigenome01/allelix/ma/mongodb/journal/j._0 Tue Oct 2 21:33:48 [initandlisten] recover cleaning up Tue Oct 2 21:33:48 [initandlisten] removeJournalFiles Tue Oct 2 21:33:48 [initandlisten] recover done Tue Oct 2 21:33:48 [websvr] admin web console waiting for connections on port 28017 Tue Oct 2 21:33:48 [initandlisten] waiting for connections on port 27017 It basically waits forever and cannot start mongodb. These servers are not webservers but they do have network access, it's a cloud computing LSF environment system. Any advice would be welcome, thanks in advance.

  Read the article

< Previous Page | 603 604 605 606 607 608 609 610 611 612 613 614  | Next Page >