Search Results

Search found 10369 results on 415 pages for 'png 24'.

Page 61/415 | < Previous Page | 57 58 59 60 61 62 63 64 65 66 67 68  | Next Page >

  • Allow access to printer between interfaces on Cisco ASA5510

    - by Jonas Stensved
    I have a Cisco ASA5510 where we have to separate networks on two separate interfaces. The networks have and should have nothing to do with each other except that network B needs to access a printer on network A. Network A: 192.168.137.0/24 Printer: 192.168.137.20 Network B: 192.168.0.0/24 I've added an incoming rule from Network A to the Printer IP in the ASDM interface but clients can't print. Our previous router was configured to let traffic through so the clients on Network B is already configured so it think it should work if the traffic is allowed. How do I let clients on Network B communicate with the printer?

    Read the article

  • Motherboard memory question

    - by JERiv
    I am currently drawing up specs on a new workstation for my office. I am considering the Asus P6X58D for a motherboard. This board's specs list it as supporting 24 gigs of memory. Suppose I were to use six four gig memory cards and then two video cards with 1 gig of memory apiece. Is the maximum supported memory similar to how 32 bit operating systems only have enough address space for 4 gigs of memory? Simply: Will the board post? If so, will the system be able to address all the memory, both the 24 gigs on the ddr3 bus and the 3 gigs on the graphics card?

    Read the article

  • How do I enable JPEG Support for PHP?

    - by ngache
    My Configure Command doesn't say anything about jpg, nor gif/png, but I can see gif/png support in the output of phpinfo(). I built PHP with --with-gd, but only GIF Support and PNG Support are in the output of phpinfo(), how do I enable JPEG Support?

    Read the article

  • Why do I have no TTY on a basic Ubuntu 9.10 server install?

    - by pr1001
    I have reinstalled Ubuntu 9.10 Server several times on a bog standard 1RU server and each time I finish the install and reboot I see GRUB run and am then presented with a black screen. The machine is running just fine, as I am able to SSH in, but I can't see anything on the attached monitor. I have a simple LCD screen connected via VGA and a signal is apparently being output to it, as it doesn't go asleep. Looking at /var/log/syslog I see: Mar 24 14:57:44 bridge5 rsyslogd-2039: Could no open output file '/dev/xconsole' [try http://www.rsyslog.com/e/2039 ] However, I later see: Mar 24 14:57:44 bridge5 kernel: [ 0.001368] console [tty0] enabled Any thoughts? Thanks!

    Read the article

  • Using sudo /etc/init.d/httpd start complains for log file rights

    - by SCO
    I created a custom log directory with the root account, and chmoded it to 777 teporarily. ls -la /var/mylogs/log/ total 16 drwxrwxrwx 2 root root 4096 Jun 24 06:27 . drwxr-xr-x 5 root root 4096 Jun 24 06:25 .. When I try to start the service from a user (lets say "myuser", which is in the sudoers files as myuser ALL=(ALL) ALL), it fails because of the permissions : sudo /etc/init.d/httpd start Starting httpd: (13)Permission denied: httpd: could not open error log file /var/mylogs/log/httpd_error.log. Unable to open logs However, the following is successfull : sudo bash /etc/init.d/http start So I guess these two methods are not equivalent, although to me doing sudo was the same than logging into the root account and issuing the commands. Any clue ? Thank you !

    Read the article

  • Triple monitor setup in linux

    - by Brendan Abel
    I'm hoping there are some xorg gurus out there. I'm trying to get a three monitor setup working in linux. I have 2 lcd monitors and a tv, all different resolutions. I'm using 2 video cards; a 9800 GTX and 7900Gt. I've seen a lot of different posts about people trying to make this work, and in every case, they either gave up, or Xinerama magically solved all their problems. Basically, my main problem is that I cannot get Xinerama to work. Every time I turn it on in the options, my machine gets stuck in a neverending boot cycle. If I disable Xinerama, I just have three Xorg screens, but I can't drag windows from one to the other. I can get the 2 lcds on Twinview, and the tv on a separate Xorg screen no problem. But I don't really like this solution. I'd rather have them all on separate screens and stitch them together with Xinerama. Has anyone done this? Here's my xorg.conf for reference. p.s. This took me all of 30 seconds to set up in Windows XP! p.s.s. I've seen somewhere that maybe randr can solve my problems? But I'm not quite sure how? Section "Monitor" Identifier "Main1" VendorName "Acer" ModelName "H233H" HorizSync 40-70 VertRefresh 60 Option "dpms" EndSection #Section "Monitor" # Identifier "Main2" # VendorName "Acer" # ModelName "AL2216W" # HorizSync 40-70 # VertRefresh 60 # Option "dpms" #EndSection Section "Monitor" Identifier "Projector" VendorName "BenQ" ModelName "W500" HorizSync 44.955-45 VertRefresh 59.94-60 Option "dpms" EndSection Section "Device" Identifier "Card1" Driver "nvidia" VendorName "nvidia" BusID "PCI:5:0:0" BoardName "nVidia Corporation G92 [GeForce 9800 GTX+]" Option "ConnectedMonitor" "DFP,DFP" Option "NvAGP" "0" Option "NoLogo" "True" #Option "TVStandard" "HD720p" EndSection Section "Device" Identifier "Card2" Driver "nvidia" VendorName "nvidia" BusID "PCI:4:0:0" BoardName "nVidia Corporation G71 [GeForce 7900 GT/GTO]" Option "NvAGP" "0" Option "NoLogo" "True" Option "TVStandard" "HD720p" EndSection Section "Module" Load "glx" EndSection Section "Screen" Identifier "ScreenMain-0" Device "Card1-0" Monitor "Main1" DefaultDepth 24 Option "Twinview" Option "TwinViewOrientation" "RightOf" Option "MetaModes" "DFP-0: 1920x1080; DFP-1: 1680x1050" Option "HorizSync" "DFP-0: 40-70; DFP-1: 40-70" Option "VertRefresh" "DFP-0: 60; DFP-1: 60" #SubSection "Display" # Depth 24 # Virtual 4880 1080 #EndSubSection EndSection Section "Screen" Identifier "ScreenProjector" Device "Card2" Monitor "Projector" DefaultDepth 24 Option "MetaModes" "TV-0: 1280x720" Option "HorizSync" "TV-0: 44.955-45" Option "VertRefresh" "TV-0: 59.94-60" EndSection Section "ServerLayout" Identifier "BothTwinView" Screen "ScreenMain-0" Screen "ScreenProjector" LeftOf "ScreenMain-0" #Option "Xinerama" "on" # most important option let you window expand to three monitors EndSection

    Read the article

  • Route eth0 to internet traffic and eth1 to local traffic

    - by Romain Caire
    How can I route all my internet traffic on eth0 (everything except 192.168.1.0/24) and route my local traffic through eth1 (192.168.1.0)? Here is my attempt : # Flush ALL THE THINGS. ip route flush table main # Restore the main table. I flushed it because OpenVPN does weird things to it. ip route add 127.0.0.0/8 via 127.0.0.1 dev lo ip route add 0.0.0.0/0 via 164.67.195.1 ip route add 192.168.1.0/24 via 192.168.1.1 ip route flush cache

    Read the article

  • Remote access to internal machine (ssh port-forwarding)

    - by MacUsers
    I have a server (serv05) at work with a public ip, hosting two KVM guests - vtest1 & vtest2 - in two different private network - 192.168.122.0 & 192.168.100.0 - respectively, this way: [root@serv05 ~]# ip -o addr show | grep -w inet 1: lo inet 127.0.0.1/8 scope host lo 2: eth0 inet xxx.xxx.xx.197/24 brd xxx.xxx.xx.255 scope global eth0 4: virbr1 inet 192.168.100.1/24 brd 192.168.100.255 scope global virbr1 6: virbr0 inet 192.168.122.1/24 brd 192.168.122.255 scope global virbr0 # [root@serv05 ~]# route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.100.0 0.0.0.0 255.255.255.0 U 0 0 0 virbr1 xxx.xxx.xx.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.122.0 0.0.0.0 255.255.255.0 U 0 0 0 virbr0 169.254.0.0 0.0.0.0 255.255.0.0 U 1002 0 0 eth0 0.0.0.0 xxx.xxx.xx.62 0.0.0.0 UG 0 0 0 eth0 I've also setup IP FORWARDing and Masquerading this way: iptables --table nat --append POSTROUTING --out-interface eth0 -j MASQUERADE iptables --append FORWARD --in-interface virbr0 -j ACCEPT All works up to this point. If I want to remote access vtest1 (or vtest2) first I ssh to serv05 and then from there ssh to vtest1. Is there a way to setup a port forwarding so that vtest1 can be accessed directly from the outside world? This is what I probably need to setup: external_ip (tcp port 4444) -> DNAT -> 192.168.122.50 (tcp port 22) I know it's easily do'able using a SOHO router but can't figure out how can I do that on a Linux box. Any help form you guys?? Cheers!! Update: 1 Now I've made ssh to listen to both of the ports: [root@serv05 ssh]# netstat -tulpn | grep ssh tcp 0 0 xxx.xxx.xx.197:22 0.0.0.0:* LISTEN 5092/sshd tcp 0 0 xxx.xxx.xx.197:4444 0.0.0.0:* LISTEN 5092/sshd and port 4444 is allowed in the iptables rules: [root@serv05 sysconfig]# grep 4444 iptables -A PREROUTING -i eth0 -p tcp -m tcp --dport 4444 -j DNAT --to-destination 192.168.122.50:22 -A INPUT -p tcp -m state --state NEW -m tcp --dport 4444 -j ACCEPT -A FORWARD -i eth0 -p tcp -m tcp --dport 4444 -j ACCEPT But I'm getting connection refused: maci:~ santa$ telnet serv05 4444 Trying xxx.xxx.xx.197... telnet: connect to address xxx.xxx.xx.197: Connection refused telnet: Unable to connect to remote host Any idea what's I'm still missing? Cheers!!

    Read the article

  • What does the the reconstruction process of mdadm do exactly on raid10

    - by Azrael
    I've got a system with 4 disks set up as raid10. All disks are usable, and mdadm all states them with UUUU. Due to a recent system crash, the raid is currently reconstruction the raid as it was marked as "not clean," and a reconstruction process was started. On a closer look smartctl shows problems on one disk: sd 0:0:0:0: [sda] Unhandled sense code sd 0:0:0:0: [sda] Result: hostbyte=DID_OK driverbyte=DRIVER_SENSE sd 0:0:0:0: [sda] Sense Key : Medium Error [current] [descriptor] Descriptor sense data with sense descriptors (in hex): 72 03 11 04 00 00 00 0c 00 0a 80 00 00 00 00 00 24 cd 78 d4 sd 0:0:0:0: [sda] Add. Sense: Unrecovered read error - auto reallocate failed sd 0:0:0:0: [sda] CDB: Read(10): 28 00 24 cd 75 1e 00 04 00 00 With a research about the reconstruction process, I only found information concerning raid5 but nothing for raid10. Can I replace this problematic disk during the reconstruction process, or will I kill the raid with this?

    Read the article

  • routing problems

    - by user174050
    I have an windows 7 laptop and I have installed openvpn 2.2x as client. The laptop has 2 ethernet cards, one of them is wireless. The wireless lan is 192.168.1.0/24 The Fix lan is 192.168.2.0/24 If I connect to the openvpn server useing the Fix lan the I can connect properly and for testing I ping to my openvpn server 10.0.0.1 that answers correctly. But if I connect to the openvpn server useing the wireless lan, I can establish the connection but pinging to the server isn´t possible. The packets goes allways lost. Why can this happen? In an other laptop where windows xp is installed and with the same lan configuratio everything works propperly. In both cases the firewall is configured to access the vnc server and the server directories useing samba. With the XP I have no problems. I will thank you for all help Ignacio

    Read the article

  • Possible HDD malfunction. Need help in diagnosing

    - by Protheus
    Today when using my PC as I did for almost 4 years I experienced the following: during opening new tab in Opera browser screen froze. Music (AIMP 3) continued to play for about 5 minutes and then stopped too. I tried Ctrl+Alt+Del, but win7 lock screen didn't appear. Caps\Scroll or Num locks didn't switch diodes on keyboard. I rebooted my PC and saw that BIOS suggests me to enter it's settings or load by default. I chose default. It don't see proper boot device (old faitful "insert proper boot" something). After second reboot it said that there is no ExpressGate installed (which i turned off in BIOS years ago). I went into BIOS setting to turn off ExpressGate and see configs: time was not set off, all hard drives present, temp and O.C. settings are nominal (no O.C.) I've inserted my Win7 install disk to try recovery. It did load awfully long (about few minutes) and didn't see current installation. PC was utilized in 24/7 mode for almost all these years. Hardware configuration: ASUS P5Q WS Core 2 Quad Q9300 (2.5GHz no O.C.) MSI geForce GTX 460 4x2 Gb GeIL EVO 2 (AFAIR) Seagate something 750Gb (4 years as system HDD 24/7) WD 1Tb (for random stuff, 5 y.o.) Hitachi 500Gb (for even more random stuff, 6 y.o.) NEC DVDRW (ALL DISKS ARE SATA) Cooler Master Silent Pro 700W Software: Windows 7 AND Kubuntu on the same drive with GRUB loader. Sorry I can't remember HDDs and can't see them right now, but I think their models aren't relevant anyway. My idea is that due to some system error or hard drive glitch i've wrecked my primary HDD's MBR. Nevertheless I don't exclude the possibility of other failure. May it's be that motherboard or it's SATA controller? Doubt it, because all drives are seen in BIOS and I could load from DVD. Maybe GRUB got bugged somehow, although I don't see how it's possible from Windows. But I did install KUbuntu from Windows (i wasn't myself then), maybe GRUB did write itself in some windows partition and got rewriteen in process? Right now I am at work with my flash drive with me and I need some advice how to fix MBR or to hear if it's not MBR. I'm going to buy new HDD (Hitachi 7k2000) because I think that my current HDD is compromised and it's unsafe to use it as system drive, especially 24/7.

    Read the article

  • How Do I Enable CUPS Browsing Across A Network?

    - by David Mackintosh
    I have a CUPS server with two print queues defined. Once this was defined, all the CUPS clients on the same subnet could see the two print queues automatically, no problem. Now I have a collection of machines on a separate subnet, reachable from the first subnet by a router. How do I enable CUPS browsing on the second set of machines so that they can see the print queues defined on the first machine? Let's call the server A.B.C.7. The first subnet is A.B.C.0/24. The second subnet is A.B.D.0/24, and there is a router with arms on both networks.

    Read the article

  • Issue about mapping MAC address to Ipv6 address

    - by deepsky
    I know that the address in ipv6 with prefix range 001 to 111 should use a 64-bit interface identifier that follows the EUI-64 format, which translates the MAC to ipv6 as below. MAC:00-02-b3-1e-83-29 --> 02-02-b3-ff-fe-1e-83-29 --->ipv6 addr: fe80::202:b3ff:fe1e:8329 Then I checked my network status with ipconfig /all on my windows XP, but it seems my ipv6 address doesn't follow the above rule: MAC:00-24-81-XX-XX-XX ipv6 addr:2001:da8:8006:225:0:24:81XX:XXXX Obviously it doesn't follow the EUI-64 format. Instead it just directly use the MAC as the last 8 bytes. Anyone know the reason? Pls Correct me if I am wrong.

    Read the article

  • Tracing out going connections

    - by Tiffany Walker
    Jan 24 07:00:49 HOST kernel: [875997.380464] Firewall: *TCP_OUT Blocked* IN= OUT=eth0 SRC=108.60.11.15 DST=74.80.225.32 LEN=52 TOS=0x00 PREC=0x00 TTL=64 ID=18789 DF PROTO=TCP SPT=64823 DPT=81 WINDOW=14600 RES=0x00 SYN URGP=0 Jan 24 07:00:50 HOST kernel: [875998.378321] Firewall: *TCP_OUT Blocked* IN= OUT=eth0 SRC=108.60.11.15 DST=74.80.225.32 LEN=52 TOS=0x00 PREC=0x00 TTL=64 ID=18790 DF PROTO=TCP SPT=64823 DPT=81 WINDOW=14600 RES=0x00 SYN URGP=0 I run fcgid so everything runs as a user. But is there a way to trace and figure out who is running an out going script? The sites all share the same IP so it's hard to know which site it is or where the script is located at.

    Read the article

  • How do I enable Ubuntu Gnome system tools

    - by RussellW
    I am running Ubuntu 10 with Gnome 2.30.2. This is a VMWare workstation image provided by another company that I do not have support in this regard. I am trying to access the graphical tools for configuring the network, users, and services but the System-Administration menu does not have these options listed. The main issue I am trying to solve is to correct the problems with the gnome menu options and network settings I have the gnome-system-tools package installed, and I am unable to run command-line versions of the tools, such as nm-applet (I get no GUI if I run that command, the process is running in the background). I realize that I can perform many tasks command-line, but I would like to use the GUI for administrative functions as I am not overly proficient for all command for restarting services and setting a static IP with a specific gateway. Further, I can run gnome-nettool, but I cannot change the IP, I can only see my network card. nm-connection-editor does not show any network cards that I can configure to change the IP. Currently, I am getting a DHCP through my NAT in VMWare, I want to set it to a specific IP address though. Preferences Menu (note some missing options) ![Preferences Menu][1] Admin Menu (note some missing options) ![Admin Menu][2] Network Tools (I can view but not change IP address) ![Network Tools][3] Network Settings (Unable to change IP address) ![Network Settings][4] Network Connections (no connections listed, not even my existing ethernet NAT connection through VMWare) ![Network Connections][5] See images here that I have referenced: 1- http://i.imgur.com/kl8pP.png 2- http://i.imgur.com/K3Cjz.png 3- Iq7Xb.png 4- 7wheV.png 5- J2ad8.png

    Read the article

  • get all ip address from subnet mask

    - by Guntis
    I have this IP list shown below. How i can calculate all ip addresses from that in Linux? Is there some tools that can calculate that for me ? I need that to check if i have not banned some cloudflare IP's. As firewall i am using shorewall and i am banning with fail2ban single IP. As i know, then i cannot detect subent mask from IP adress, right? 204.93.240.0/24 204.93.177.0/24 199.27.128.0/21 173.245.48.0/20 103.22.200.0/22 141.101.64.0/18 108.162.192.0/18 190.93.240.0/20 188.114.96.0/20

    Read the article

  • 'IPv6' Newbie with IPv6 address assigment

    - by Cute Puppy
    I am new to IP v6 and I am looking to translate some existing private IPv4 addresses into v6 address assignment. Can someone please help me to answer/explain the questions below? If I have an v4 address of: 10.10.0.0/22 10.10.1.0/22 10.10.2.0/22 10.10.3.0/22 10.10.8.0/20 10.20.1.0/24 What will the new v6 address to be? I have been looking online @ http://www.subnetonline.com/pages/subnet-calculators/ipv4-to-ipv6-converter.php or other sites, Seems like they translated it directly to be: fe80::a0a:0 /118 fe80::a0a:100 /118 fe80::a0a:200 /118 fe80::a0a:300 /118 fe80::a0a:800 /118 fe80::a14:100 /120 Can someone please explain to me how we get to /118 from either "/22 or /24" (1. and 5) In addition, I would like to create the new private address based on the Unique local address "fc00::/16" How do I expand from there? Any help is greatly appreciated it!! Thanks,

    Read the article

  • What is good RAM for my CPU?

    - by Jason94
    I'm going to upgrade my RAM, but I have no clue what to look for. There is cheap and there is expensive RAM. What should I look for? What are good attributes for intel i5? The i5 CPU and motherboeard supports 1600 MHz (PC3-12800), but there is still to much to choose from. There are CL10 (10-10-10-27) @ 1.5V CL11 @ 1.35V CL9 (9-9-9-24) @ 1.5V CL9 (9-9-9-24) @ 1.65V Higher CL is better? CL is classification? And I guess a high voltage is also good since thats what overclockers do to the ram (increase the voltage)?

    Read the article

  • How to route traffic from VM (Parallels) over an Open VPN connection on the host (OS X)

    - by withakay
    Scenario: I have a Mac running Lion that is connected to an OpenVPN server I have a Windows XP VM (running on parallels, but I don't think this is important) I want to be able to route traffic from the XP VM via the host Mac's OpenVPN connection so that I can log on to a domain. The remote network is 172.16.0.0/23 (255.255.254.0) Open VPN is configured to supply address in the 10.100.101.0/24 range and sets up the routing to 172.16.0.0 using the gateway 10.100.101.1/32 My local network is 192.16.1.0/24 NOTE: I do not want to install OpenVPN into the XP virtual machine as I would have to use a passwordless key in order for OpenVPN to connect before logon. Anyone got any ideas?

    Read the article

  • Problem connecting with RDP between Mac and Win2k3 server

    - by salle55
    I have an iMac running Mac OS X 10.5.8 and the RDP Connection Client 2.0.1. http://salle.dyndns.org/misc/rdp%5Fproblem1.png When I try to connect to a Windows 2003 Server on the same network I get a dialog saying "Remote Desktop Connection cannot verify the identity of the computer that you want to connect to". Picture: salle.dyndns.org/misc/rdp_problem2.png And when I press the Connect-button in the previous dialog I get the same message in another dialog: Picture: salle.dyndns.org/misc/rdp_problem3.png I can connect to the Win2k3 server from a Vista machine, and it used to work from the Mac as well. I stopped working from the Mac after I did some configuration on the win2k3 server, removed and added the the connection in the Terminal Services Configuration: Picture: salle.dyndns.org/misc/rdp_problem4.png What do I need to do to be able to connect from the Mac again? (I have not enough reputation to post multiple links or images)

    Read the article

  • Why is Windows 7 not following all routes?

    - by GigabyteProductions
    My computer is connected to my secondary router that's running the 192.168.42.0/24 network and my computer also has a route that directs anything on that network to the router, but for anything on that network other than the router itself, it get's the ICMP response of Reply from 192.168.42.194: Destination host unreachable. (with 192.168.42.194 being my computer). Every other network works, like all of the internet, or addresses on my primary router like 192.168.1.*, just not on the 192.168.42.0/24 network... route print returns: IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.42.1 192.168.42.194 276 127.0.0.0 255.0.0.0 On-link 127.0.0.1 306 127.0.0.1 255.255.255.255 On-link 127.0.0.1 306 127.255.255.255 255.255.255.255 On-link 127.0.0.1 306 192.168.42.0 255.255.255.0 On-link 192.168.42.194 276 192.168.42.194 255.255.255.255 On-link 192.168.42.194 276 192.168.42.255 255.255.255.255 On-link 192.168.42.194 276 224.0.0.0 240.0.0.0 On-link 127.0.0.1 306 224.0.0.0 240.0.0.0 On-link 192.168.42.194 276 255.255.255.255 255.255.255.255 On-link 127.0.0.1 306 255.255.255.255 255.255.255.255 On-link 192.168.42.194 276 =========================================================================== Persistent Routes: Network Address Netmask Gateway Address Metric 0.0.0.0 0.0.0.0 192.168.42.1 Default =========================================================================== The only time anything is supposed to send an ICMP Host Unreachable response is when there's no route to it, right? So, why is my own computer sending that to ping or tracert when I have the route of 192.168.42.0 with the mask of 255.255.255.0? An IP address of 192.168.42.2 surely fits into that route. If I explicitly add a route for the IP address i am trying to access, it works, like: route add 192.168.42.2 mask 255.255.255.255 192.168.42.1 (the 192.168.42.1 right after mask is gateway, or the device to send the packet to so it can route it further), but why wont it work for the implicit route that's automatically on the table? I disabled my firewall, too (I use Comodo if anyone thinks this still serves as a problem). I'v even tried explicitly adding the gateway of 192.168.42.1 to the 192.168.42.0/24 route instead of it routing through 0.0.0.0's gateway, which is what On-link does. but that didn't work either, so it's not a gateway specification problem. If the host was really unreachable, it would be the router's IP address (192.168.42.1) sending that to me... This network is all of my creation, so there's no problem such as an administrator locking me out, because i am the administrator.

    Read the article

  • The sound freezes while listening to music

    - by Scott
    I have bought an sound card - Sound Blaster X-FI Surround 5.1 PRO and while I'm listening to the music, after few minutes or even hours (it does happends randomly) the sound dissapears and I have to go settings: Playing Devices - Advanced and switch the Default Format (sampling frequency) and switch from the `16-bits, 48000 Hz (DVD Quality) to any other from the list (16-bits, 96000 Hz or 24-bits, 48000 Hz or 24-bits 96000 Hz). I have been trying to set all of the above options, but for all of them the sound freezes after listening to music. It is getting annoying and I hope its the settings fault and not my sound card. I got my drivers installed from the attached CD and I'm running Windows 7 HP 64 bits. If anyone would try to help me, I would really appreciate this.

    Read the article

  • 2 "P4" power connectors *AND* an 8 pin EPS connector -- all necessary?

    - by chris
    I recently bought an Arima SW350 motherboard. It supports 16 ddr simms as well as 2 opteron 2xx CPUs, so I imagine it may have pretty heavy power requirements... It has a 24 pin ATX power connector, 2 4 pin "P4" power connectors, and an 8 pin EPS power connector. My supermicro power supply has a 24 pin ATX connector and the EPS connector, and one P4 connector. Can I safely run this thing with only one P4 connector plugged in? Can I safely get a "hard disk to P4" adapter and use that to power the other P4 connector on the motherboard? Do I just need a new power supply? The board's documentation is pretty thin on the topic.

    Read the article

  • nginx not returning 304 on cached content

    - by Don H
    I'm using nginx as a reverse proxy with an Apache back-end handling some PHP files. The files return the right expiry headers and proxy_cache does a good job of caching them, but I've noticed that the cached content returns a 200 on every refresh, when it might be more efficient to return a 304 on the cached files. The files in question are generated by PHP. The urls do not have .php in them as they've been prettified. Any idea why nginx might not be returning 304 on repeated visits to a cached PHP output? To clarify: It's using proxy_cache for caching dynamic PHP pages (not static html pages generated by PHP). I'm setting expires headers in the PHP file of time + 24 hours. With that in mind, I was hoping nginx would be able to then return 304s on its cached versions during that 24 hour window.

    Read the article

  • Can't figure out this file behavior in IOS 4.2

    - by Don Jones
    Odd behavior with file behavior. Here's the thing: I'm using the phone camera to snap a picture, and internally generating a thumbnail. I'm saving those as temp files in the Documents directory. Here's the complete code: - (void)imagePickerController:(UIImagePickerController *)picker didFinishPickingMediaWithInfo:(NSDictionary *)info { UIImage *photo = [info objectForKey:@"UIImagePickerControllerOriginalImage"]; photo = [self scaleAndRotateImage:photo]; // save photo NSString *docsDir = [NSHomeDirectory() stringByAppendingPathComponent:@"Documents"]; NSLog(@"Writing to %@",docsDir); // save photo file NSLog(@"Saving photo as %@",[NSString stringWithFormat:@"%@/temp_photo.png",docsDir]); [UIImagePNGRepresentation(photo) writeToFile:[NSString stringWithFormat:@"%@/temp_photo.png",docsDir] atomically:YES]; // make and save thumbnail NSLog(@"Saving thumbnail as %@",[NSString stringWithFormat:@"%@/temp_thumb.png",docsDir]); UIImage *thumb = [self makeThumbnail:photo]; [UIImagePNGRepresentation(thumb) writeToFile:[NSString stringWithFormat:@"%@/temp_thumb.png",docsDir] atomically:YES]; NSFileManager *manager = [NSFileManager defaultManager]; NSError *error; NSArray *files = [manager contentsOfDirectoryAtPath:docsDir error:&error]; NSLog(@"\n\nThere are %d files in the documents directory %@",(files.count),docsDir); for (int i = 0; i < files.count; i++) { NSString *filename = [files objectAtIndex:i]; NSLog(@"Seeing filename %@",filename); } // done //[photo release]; //[thumb release]; [self dismissModalViewControllerAnimated:NO]; [delegate textInputFinished]; } As you can see, I've put quite a bit of logging in here in an attempt to figure out my problem (which is coming up). The log output to this point is: Writing to /var/mobile/Applications/77D792DC-A224-4A47-8A4C-BB7C557626F3/Documents Saving photo as /var/mobile/Applications/77D792DC-A224-4A47-8A4C-BB7C557626F3/Documents/temp_photo.png Saving thumbnail as /var/mobile/Applications/77D792DC-A224-4A47-8A4C-BB7C557626F3/Documents/temp_thumb.png There are 3 files in the documents directory /var/mobile/Applications/77D792DC-A224-4A47-8A4C-BB7C557626F3/Documents Seeing filename temp_photo.png Seeing filename temp_text.txt Seeing filename temp_thumb.png This is absolutely as-expected. I clearly have three files on the device. Here's the very next code that operates - the code that received the textInputFinished message: - (void)textInputFinished { NSFileManager *fileManager = [NSFileManager defaultManager]; NSString *docsDir = [NSHomeDirectory() stringByAppendingPathComponent:@"Documents"]; NSError *error; // get next filename NSString *filename; int i = 0; do { i++; filename = [NSString stringWithFormat:@"%@/reminder_%d",docsDir,i]; NSLog(@"Trying filename %@",filename); } while ([fileManager fileExistsAtPath:[filename stringByAppendingString:@".txt"]]); NSLog(@"New base filename is %@",filename); NSArray *files = [fileManager contentsOfDirectoryAtPath:docsDir error:&error]; NSLog(@"There are %d files in the directory %@",(files.count),docsDir); This is testing to get a new, non-temp, not-in-use filename. It does that - but then it says there aren't any files in the documents folder! Here's the logged output: Trying filename /var/mobile/Applications/77D792DC-A224-4A47-8A4C-BB7C557626F3/Documents/reminder_1 New base filename is /var/mobile/Applications/77D792DC-A224-4A47-8A4C-BB7C557626F3/Documents/reminder_1 There are 0 files in the directory /var/mobile/Applications/77D792DC-A224-4A47-8A4C-BB7C557626F3/Documents What the heck? Where did the three files go?

    Read the article

< Previous Page | 57 58 59 60 61 62 63 64 65 66 67 68  | Next Page >