Search Results

Search found 17267 results on 691 pages for 'dynamic ip'.

Page 618/691 | < Previous Page | 614 615 616 617 618 619 620 621 622 623 624 625  | Next Page >

  • Connect to Apache times out randomly

    - by Amadan
    We are trying to set up an Apache server on a remote machine, but we experience strange behaviour. Checking with telnet remote.machine 80, one of these things happen randomly: Connect and serve content normally (no delay) Connect after a long pause Connect normally, then time out without response Timeout on connect Once connected, the request seems to be processed normally. These things do not occur if I connect from that machine directly to localhost 80. The Apache is dedicated, as is the server it runs on (runs only this one application, no-one else is using it for anything else). I am not an administrator of the remote site, and I do not know the network architecture over there, but apparently it's firewalled: (HTTP port is open, SSH port is IP-restricted, most others are closed). If there was any one pattern, I might have some ideas, but this variety of symptoms baffles me. Any ideas as to what could be causing this? Apache is 2.2; Server version is: Linux version 2.6.9-22.ELsmp ([email protected]) (gcc version 3.4.4 20050721 (Red Hat 3.4.4-2)) #1 SMP Mon Sep 19 18:32:14 EDT 2005

    Read the article

  • CUPS printer on Vritual Machine can be access via CUPS admin, but not by XP?

    - by SJaguar13
    I have a Zebra label printer connected to a Linux Mint virtual machine. It was set up with CUPS and a Windows XP computer can then print to it via http://192.168.1.76:632/printers/labelprinter. That was all fine and dandy I then hooked up a Fargo Pro L PVC card printer to a Windows XP virtual machine. I had to disconnect the label printer as the server that hosted both virtual machines only has 1 parallel port. Now I plugged in the Zebra again, and it cannot print from the Windows XP computer anymore. If I go to the CUPS admin panel on the Windows XP computer, I can see it, everything looks fine, and I can send it a test page to print which works. If I try to print from Windows, I get an error that the printer is not found/cannot connect to the server. The only other thing that changed was the firewall on the router to allow remote desktop to another computer from outside the network, but all the firewall stuff was for external use. Nothing affected the IP address of the internal network. The Linux Mint VM also had a PDF pritner that was shared with CUPS. That printer is also down. I tried setting up a new CUPS installation on another VM, and when I go to share it with XP, I get the same error. I don't know what to try. It has access, it can get to the admin from that computer, it seems to be up and ready, but when Windows tries to connect, the printer isn't found even though 4 days ago everything was fine. Any ideas?

    Read the article

  • Win Svr 2003 DHCP Bad Addresses

    - by VinceM
    After looking at other posts I still can figure this out. I'll start at the beginning... I inherited this network and I'm not the most knowledgeable about networking... We have a AD DHCP Server that is also our DNS server, We were having some VPN issues (on the same server) and my boss decided to disable routing and remote access, which cleared the settings. We couldn't get it set back up correctly so we rolled back to a backup drive they created a number of months ago. Since rolling back I've had Bad_Address listings in DHCP and there is a number of duplicate records in the DNS Forward Lookup Zones. We have less than 50 devices on the network but I have over 90 Bad Addresses showing. This server is currently running but we get IP address conflicts all the time on pretty much all the computers. I have had people do release and renew but it didn't help... I have also deleted and re-added the scope to no avail either. Any help or ideas would be greatly appreciated and I apologize if I missed another post that has information to help. Thanks, Vince

    Read the article

  • Lion MacBook Pro will not load webpages with DNS just after wake

    - by NReilingh
    I'm working with a 2011 MacBook Pro running Lion (10.7.2), that after waking from sleep (i.e. opening the lid) takes an inordinately long amount of time (2-3 minutes or more) to get a usable internet connection. Upon waking, the wi-fi icon signifies it is negotiating a network connection, and completes one a few seconds later. At this point, network diagnostics will not show any issues, and everything in Network preferences looks as normal: I'm connected to the proper network, have the right IP address and gateway, and DNS settings are correct. However, any site accessed with a domain name (like http://www.google.com) in Safari will return the "You are not connected to the Internet." error. Accessing a site directly, say, with Google's 74.125.226.212, is successful. Yet, Network Diagnostics will insist that DNS is functioning properly. After a few minutes, the following lines will be printed to the Console log, and regular behavior will be restored. 11/18/11 8:11:31.288 PM airportd: _doAutoJoin: Already associated to “Wireless”. Bailing on auto-join. 11/18/11 8:11:32.000 PM kernel: en1: BSSID changed to 00:25:9c:63:91:bd This behavior occurs only when waking from sleep--not when turning wi-fi on and off. This problem also occurs when using a wired Ethernet connection. As per this thread, I have tried flushing the DNS cache and wiping the wireless network from memory (it's not a protected network). Neither have worked.

    Read the article

  • Percona-server time out on /etc/init.d/mysql start

    - by geekmenot
    Every time I start mysql, using /etc/init.d/mysql start or service mysql start, it always times out. * Starting MySQL (Percona Server) database server mysqld [fail] However, I can get into mysql. Just wanted to know if there is a problem with the install because it happens all the time, not a one off error. mysql-error.log shows: 121214 11:25:56 mysqld_safe Starting mysqld daemon with databases from /data/mysql/ 121214 11:25:56 [Note] Plugin 'FEDERATED' is disabled. 121214 11:25:56 InnoDB: The InnoDB memory heap is disabled 121214 11:25:56 InnoDB: Mutexes and rw_locks use GCC atomic builtins 121214 11:25:56 InnoDB: Compressed tables use zlib 1.2.3 121214 11:25:56 InnoDB: Using Linux native AIO 121214 11:25:56 InnoDB: Initializing buffer pool, size = 14.0G 121214 11:25:58 InnoDB: Completed initialization of buffer pool 121214 11:26:01 InnoDB: Waiting for the background threads to start 121214 11:26:02 Percona XtraDB (http://www.percona.com) 1.1.8-rel29.2 started; log sequence number 9333955393950 121214 11:26:02 [Note] Server hostname (bind-address): '0.0.0.0'; port: 3306 121214 11:26:02 [Note] - '0.0.0.0' resolves to '0.0.0.0'; 121214 11:26:02 [Note] Server socket created on IP: '0.0.0.0'. 121214 11:26:02 [Note] Slave SQL thread initialized, starting replication in log 'mysql-bin.005163' at position 624540946, relay log '/data/mysql/mysql-relay-bin.000043' position: 624541092 121214 11:26:02 [Note] Slave I/O thread: connected to master '[email protected]:3306',replication started in log 'mysql-bin.005180' at position 823447620 121214 11:26:02 [Note] Event Scheduler: Loaded 0 events 121214 11:26:02 [Note] /usr/sbin/mysqld: ready for connections. Version: '5.5.28-29.2-log' socket: '/data/mysql/mysql.sock' port: 3306 Percona Server (GPL), Release 29.2

    Read the article

  • Configure Nginx to render static files and rewrite file extension or proxy_pass

    - by Pardoner
    I've set up Nginx to handle all my static files else proxy_pass to a Node.js server. It's working fine but I'm having difficulty rewriting the url so that it remove the .html file extension. upstream my_upstream { server 127.0.0.1:8000; keepalive 64; } server { listen 80; server_name staging.mysite.com; root /var/www/staging.mysite.org/public; access_log /var/logs/staging.mysite.org.access.log; error_log /var/logs/staging.mysite.org.error.log; location ~ ^/(images/|javascript/|css/|robots.txt|humans.txt|favicon.ico) { rewrite (.*)\.html $1 permanent; try_files $uri.html $uri/ /index.html; access_log off; expires max; } location / { proxy_redirect off; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header X-Forwarded-Proto $scheme; proxy_set_header Host $http_host; proxy_set_header X-NginX-Proxy true; proxy_set_header Connection ""; proxy_http_version 1.1; proxy_cache one; proxy_cache_key sfs$request_uri$scheme; proxy_pass http://my_upstream; } }

    Read the article

  • DDoS nulling to some ips and other options?

    - by Prix
    I am looking for some information in regards DDoS in the follow scenario: I have a server that is behind a Cisco Guard and it will be DDoS'ed, I only care about a set list of IPS that by not means are the attackers. Is it possible to null all other ips but this list to actually get any response to my server or in the long run no matter what I do if they have enough DDoS power I will just go down like a flie ? Is there any recommended company out there that can actually cope with a DDoS ? My server will mainly run several clients that will get connected to a external server and all it needs access to is my local MySQL the the private network so I can access it. There will be no other services runnings such as web or ftp etc at least not to the external ips of the server if i ever have to have any of these service they will be on the private network. The MySQL will be available externally only to 1 safe ip not known by anyone but me and internally at localhost + private network. Are there any solutions ?

    Read the article

  • Issues with Apache redirect to www-prefixed URL

    - by lamp_scaler
    I have a website with domain mysite.com. I would like to have it so that if a user types in "mysite.com" it will redirect to "www.mysite.com". Additionally, "mysite.com/subdir" will also redirect to "www.mysite.com/subdir". I've looked and made changes with vhosts and also rewrites, but it's not working for the "mysite.com/subdir"-"www.mysite.com/subdir" case. Every time I type in "mysite.com/subdir", it will redirect to "www.mysite.com". Only "www.mysite.com/subdir" works. Not sure how to troubleshoot this. I turned on rewrite logs and didn't see anything obvious, yet. This is my config files so far. Please let me know what I'm missing. Thanks! FYI: I'm using CentOS 5.4, nginx 1.2.0 on top of Apache 2.2.3. The site itself is built with CodeIgniter framework. http.conf: ServerTokens Prod ServerRoot "/etc/httpd" PidFile run/httpd.pid Timeout 120 KeepAlive Off MaxKeepAliveRequests 100 KeepAliveTimeout 15 <IfModule prefork.c> StartServers 8 MinSpareServers 5 MaxSpareServers 10 ServerLimit 256 MaxClients 60 MaxRequestsPerChild 10000 #StartServers 8 #MinSpareServers 5 #MaxSpareServers 20 #ServerLimit 256 #MaxClients 256 #MaxRequestsPerChild 4000 </IfModule> <IfModule worker.c> StartServers 2 MaxClients 150 MinSpareThreads 25 MaxSpareThreads 75 ThreadsPerChild 25 MaxRequestsPerChild 0 </IfModule> Listen 69 LoadModule auth_basic_module modules/mod_auth_basic.so LoadModule auth_digest_module modules/mod_auth_digest.so LoadModule authn_file_module modules/mod_authn_file.so LoadModule authn_alias_module modules/mod_authn_alias.so LoadModule authn_anon_module modules/mod_authn_anon.so LoadModule authn_dbm_module modules/mod_authn_dbm.so LoadModule authn_default_module modules/mod_authn_default.so LoadModule authz_host_module modules/mod_authz_host.so LoadModule authz_user_module modules/mod_authz_user.so LoadModule authz_owner_module modules/mod_authz_owner.so LoadModule authz_groupfile_module modules/mod_authz_groupfile.so LoadModule authz_dbm_module modules/mod_authz_dbm.so LoadModule authz_default_module modules/mod_authz_default.so LoadModule ldap_module modules/mod_ldap.so LoadModule authnz_ldap_module modules/mod_authnz_ldap.so LoadModule log_config_module modules/mod_log_config.so LoadModule logio_module modules/mod_logio.so LoadModule env_module modules/mod_env.so LoadModule ext_filter_module modules/mod_ext_filter.so LoadModule mime_magic_module modules/mod_mime_magic.so LoadModule expires_module modules/mod_expires.so LoadModule deflate_module modules/mod_deflate.so LoadModule headers_module modules/mod_headers.so LoadModule usertrack_module modules/mod_usertrack.so LoadModule setenvif_module modules/mod_setenvif.so LoadModule mime_module modules/mod_mime.so LoadModule dav_module modules/mod_dav.so LoadModule autoindex_module modules/mod_autoindex.so LoadModule dav_fs_module modules/mod_dav_fs.so LoadModule vhost_alias_module modules/mod_vhost_alias.so LoadModule negotiation_module modules/mod_negotiation.so LoadModule dir_module modules/mod_dir.so LoadModule actions_module modules/mod_actions.so LoadModule speling_module modules/mod_speling.so LoadModule alias_module modules/mod_alias.so LoadModule rewrite_module modules/mod_rewrite.so LoadModule proxy_module modules/mod_proxy.so LoadModule proxy_balancer_module modules/mod_proxy_balancer.so LoadModule proxy_ftp_module modules/mod_proxy_ftp.so LoadModule proxy_http_module modules/mod_proxy_http.so LoadModule proxy_connect_module modules/mod_proxy_connect.so LoadModule cache_module modules/mod_cache.so LoadModule suexec_module modules/mod_suexec.so LoadModule disk_cache_module modules/mod_disk_cache.so LoadModule file_cache_module modules/mod_file_cache.so LoadModule mem_cache_module modules/mod_mem_cache.so LoadModule cgi_module modules/mod_cgi.so LoadModule version_module modules/mod_version.so #rpaf settings LoadModule rpaf_module modules/mod_rpaf-2.0.so RPAFenable On RPAFproxy_ips 127.0.0.1 RPAFsethostname On # The header where the real client IP address is stored. RPAFheader X-Forwarded-For Include conf.d/*.conf User apache Group apache ServerAdmin root@localhost ServerName www.mysite.com:80 UseCanonicalName Off DocumentRoot "/var/www/html" <Directory /> Options FollowSymLinks AllowOverride All </Directory> <Directory "/var/www/html"> Options Indexes FollowSymLinks AllowOverride All Order allow,deny Allow from all </Directory> <IfModule mod_userdir.c> UserDir disable </IfModule> DirectoryIndex index.html index.html.var AccessFileName .htaccess <Files ~ "^\.ht"> Order allow,deny Deny from all </Files> <DirectoryMatch "^/.*/\.svn/"> Order deny,allow Deny from all </DirectoryMatch> TypesConfig /etc/mime.types DefaultType text/plain <IfModule mod_mime_magic.c> MIMEMagicFile conf/magic </IfModule> HostnameLookups Off ErrorLog logs/error_log LogLevel warn LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %b" common LogFormat "%{Referer}i -> %U" referer LogFormat "%{User-agent}i" agent CustomLog logs/access_log combined ServerSignature Off Alias /icons/ "/var/www/icons/" <Directory "/var/www/icons"> Options Indexes MultiViews AllowOverride None Order allow,deny Allow from all </Directory> <IfModule mod_dav_fs.c> DAVLockDB /var/lib/dav/lockdb </IfModule> ScriptAlias /cgi-bin/ "/var/www/cgi-bin/" <Directory "/var/www/cgi-bin"> AllowOverride None Options None Order allow,deny Allow from all </Directory> IndexOptions FancyIndexing VersionSort NameWidth=* HTMLTable AddIconByEncoding (CMP,/icons/compressed.gif) x-compress x-gzip AddIconByType (TXT,/icons/text.gif) text/* AddIconByType (IMG,/icons/image2.gif) image/* AddIconByType (SND,/icons/sound2.gif) audio/* AddIconByType (VID,/icons/movie.gif) video/* AddIcon /icons/binary.gif .bin .exe AddIcon /icons/binhex.gif .hqx AddIcon /icons/tar.gif .tar AddIcon /icons/world2.gif .wrl .wrl.gz .vrml .vrm .iv AddIcon /icons/compressed.gif .Z .z .tgz .gz .zip AddIcon /icons/a.gif .ps .ai .eps AddIcon /icons/layout.gif .html .shtml .htm .pdf AddIcon /icons/text.gif .txt AddIcon /icons/c.gif .c AddIcon /icons/p.gif .pl .py AddIcon /icons/f.gif .for AddIcon /icons/dvi.gif .dvi AddIcon /icons/uuencoded.gif .uu AddIcon /icons/script.gif .conf .sh .shar .csh .ksh .tcl AddIcon /icons/tex.gif .tex AddIcon /icons/bomb.gif core AddIcon /icons/back.gif .. AddIcon /icons/hand.right.gif README AddIcon /icons/folder.gif ^^DIRECTORY^^ AddIcon /icons/blank.gif ^^BLANKICON^^ DefaultIcon /icons/unknown.gif #AddDescription "GZIP compressed document" .gz #AddDescription "tar archive" .tar #AddDescription "GZIP compressed tar archive" .tgz ReadmeName README.html HeaderName HEADER.html IndexIgnore .??* *~ *# HEADER* README* RCS CVS *,v *,t AddLanguage ca .ca AddLanguage cs .cz .cs AddLanguage da .dk AddLanguage de .de AddLanguage el .el AddLanguage en .en AddLanguage eo .eo AddLanguage es .es AddLanguage et .et AddLanguage fr .fr AddLanguage he .he AddLanguage hr .hr AddLanguage it .it AddLanguage ja .ja AddLanguage ko .ko AddLanguage ltz .ltz AddLanguage nl .nl AddLanguage nn .nn AddLanguage no .no AddLanguage pl .po AddLanguage pt .pt AddLanguage pt-BR .pt-br AddLanguage ru .ru AddLanguage sv .sv AddLanguage zh-CN .zh-cn AddLanguage zh-TW .zh-tw LanguagePriority en zh-CN zh-TW ca cs da de el eo es et fr he hr it ja ko ltz nl nn no pl pt pt-BR ru sv ForceLanguagePriority Prefer Fallback AddDefaultCharset UTF-8 AddType text/x-component .htc AddType application/x-compress .Z AddType application/x-gzip .gz .tgz AddHandler type-map var AddType text/html .shtml AddOutputFilter INCLUDES .shtml Alias /error/ "/var/www/error/" <IfModule mod_negotiation.c> <IfModule mod_include.c> <Directory "/var/www/error"> AllowOverride None Options IncludesNoExec AddOutputFilter Includes html AddHandler type-map var Order allow,deny Allow from all LanguagePriority en es de fr ForceLanguagePriority Prefer Fallback </Directory> </IfModule> </IfModule> BrowserMatch "Mozilla/2" nokeepalive BrowserMatch "MSIE 4\.0b2;" nokeepalive downgrade-1.0 force-response-1.0 BrowserMatch "RealPlayer 4\.0" force-response-1.0 BrowserMatch "Java/1\.0" force-response-1.0 BrowserMatch "JDK/1\.0" force-response-1.0 BrowserMatch "Microsoft Data Access Internet Publishing Provider" redirect-carefully BrowserMatch "MS FrontPage" redirect-carefully BrowserMatch "^WebDrive" redirect-carefully BrowserMatch "^WebDAVFS/1.[0123]" redirect-carefully BrowserMatch "^gnome-vfs/1.0" redirect-carefully BrowserMatch "^XML Spy" redirect-carefully BrowserMatch "^Dreamweaver-WebDAV-SCM1" redirect-carefully vhost.conf: NameVirtualHost *:69 <VirtualHost *:69> ServerName mysite.com ServerAlias vip.mysite.com Redirect / http://www.mysite.com/ </VirtualHost> <VirtualHost *:69> DocumentRoot /home/mysite/mysite/www ServerName www.mysite.com </VirtualHost> <VirtualHost *:69> DocumentRoot /home/mysite/mysite/www/assets ServerName static.mysite.com </VirtualHost> <VirtualHost *:69> DocumentRoot /home/mysite/admin/www ServerName admin.mysite.com </VirtualHost> <VirtualHost *:69> DocumentRoot /home/other/trunk/www ServerName othersite.com ServerAlias www.othersite.com </VirtualHost> <VirtualHost *:69> DocumentRoot /var/www/html ServerName test.mysite.com ServerAlias test2.mysite.com </VirtualHost> /home/mysite/mysite/www/.htaccess: RewriteEngine on # In my case all CI files are outside this web root, so we can # allow any files or directories that exist to be displayed directly RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d # hide index.php RewriteRule .* index.php/$0 [L] # BEGIN Compress text files <ifModule mod_deflate.c> <filesMatch "\.(css|js|x?html?|php)$"> SetOutputFilter DEFLATE </filesMatch> </ifModule> # END Compress text files # BEGIN Expire headers <ifModule mod_expires.c> ExpiresActive On ExpiresDefault "access plus 1 seconds" ExpiresByType image/x-icon "access plus 2592000 seconds" ExpiresByType image/jpeg "access plus 2592000 seconds" ExpiresByType image/png "access plus 2592000 seconds" ExpiresByType image/gif "access plus 2592000 seconds" ExpiresByType application/x-shockwave-flash "access plus 2592000 seconds" ExpiresByType text/css "access plus 604800 seconds" ExpiresByType text/javascript "access plus 604800 seconds" ExpiresByType application/javascript "access plus 604800 seconds" ExpiresByType application/x-javascript "access plus 604800 seconds" ExpiresByType application/xhtml+xml "access plus 600 seconds" </ifModule> # END Expire headers # BEGIN Cache-Control Headers <ifModule mod_headers.c> <filesMatch "\.(ico|jpe?g|png|gif|swf)$"> Header set Cache-Control "max-age=2592000, public" </filesMatch> <filesMatch "\.(css)$"> Header set Cache-Control "max-age=604800, public" </filesMatch> <filesMatch "\.(js)$"> Header set Cache-Control "max-age=604800, private" </filesMatch> </ifModule> # END Cache-Control Headers # BEGIN Turn ETags Off <ifModule mod_headers.c> Header unset ETag </ifModule> FileETag None # END Turn ETags Off /etc/nginx/conf.d/default.conf: server { listen 80; server_name static.mysite.com; location / { root /home/mysite/mysite/www/assets; index index.html index.htm; expires max; } } server { listen 80; server_name *.mysite.com www.mysite.com vip.mysite.com; #Set this larger if uploading big files client_max_body_size 5m; location / { proxy_pass http://127.0.0.1:69; proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_connect_timeout 90; proxy_send_timeout 90; proxy_read_timeout 90; #client_max_body_size 10m; client_body_buffer_size 128k; proxy_buffer_size 4k; proxy_buffers 4 32k; } }

    Read the article

  • Single m0n0wall - Two LAN Subnets - How To Setup

    - by SnAzBaZ
    I have two LAN subnets that I need to link together they are 192.168.4.0/24 and 192.168.5.0/24 There is a m0n0wall running on 192.168.4.1. It's LAN connection goes out to our network switch, and it's WAN port goes out to our ADSL modem. WAN is connected via PPPoE. The 192.168.4.0 subnet contains all of our office workstations. The 192.168.5.0 subnet contains development servers and test machines that need to obtain internet access and be "managed" by computers on the 192.168.4.0 subnet, but need to be on their own subnet as well. I have a Draytek 2820N configured on 192.168.5.1 with it's WAN2 port configured as 192.168.4.25 and a default gateway of 192.168.4.1. Machines on the 5.0 subnet can connect to the internet via the m0n0wall just fine. I configured a static route on the m0n0wall LAN interface, Network 192.168.5.0/24 and Gateway 192.168.4.25. Machines on the 5.0 subnet can ping machines on the 4.0 network but the reverse does not work. I configured a new firewall rule on the m0n0wall that allows any traffic on the LAN interface with a source IP of 192.168.4.25 to be allowed. The DrayTek firewall is currently configured to pass all traffic regardless. When I try to ping a machine in the 5.0 subnet from 4.0 I see this in my m0n0wall log: BLOCK 14:45:27.888157 LAN 192.168.4.25 192.168.4.37, type echoreply/0 ICMP So the reply is being sent from the 5.0 subnet but is not being allowed to reach my workstation because the firewall is blocking it. Why is the firewall blocking it ? I hope the explanation of my network is clear, please ask if you require further clarification. Thank you.

    Read the article

  • WOL doesn't work if set to anything other than `a` but this setting makes it boot all the time

    - by Elton Carvalho
    I manage a small "cluster" of 4 Xeon machines with Intel boards in my lab. They are all plugged to a 5-port 3-Com switch with static IP addresses like 10.0.0.x. They are all running OpenSuse 11.4 and their /home/ is served by one of the machines (node00) via NFS. They are plugged to an UPS that can keep them on for ca. 15 minutes, but there are lots of electric shortages due to "unscheduled maintenace" that are longer than this. So they end up being powered down without notice. If I set the BIOS to turn them on after power shortages, the issue is that they all boot at the same time and, if node00 decides to run fsck in the /home/ partition, it does not finish booting before the others try to NFS mount their /home/. I am trying to make wake on lan work, so I can choose to boot the NFS clients only after the server has successfully booted. The problem is that when I run ethtool I get an output like this: Supports Wake-on: pumbag Wake-on: g Theoretically, it is set to wake on MagicPacket(tm), according to the manual. But sending the WOL packet using wol -i 10.0.0.255 $MACADDR does not wake up the box after I shut it down with halt. The ethernet link led blinks after I send the packet, so it appears to be getting to the machine. However, if I set it up with ethtool -s eth1 wol bag, the machine always wakes up right after halting, even if I don't send the Magic packet. This means that the device can wake up with LAN activity, but seems to be ignoring the magic packet. Setting wol ag does not wake the box with the MagicPacket. Does setting wol a mean that it should boot with any broadcast message? How can I diagnose the issue of the machine not waking up with the MagicPacket even though I am sending it and it's set up to wake up with it? Thanks in advance!

    Read the article

  • How to determine the root cause of a system lockup on Ubuntu 8.04 LTS?

    - by jdt141
    I'm currently working a project that involves setting up a PC/104 stack and running Ubuntu 8.04 LTS. We need to use the PC/104 stack because its an embedded application - and we're required to use a DeviceNet peripheral card to communicate to other devices. (DeviceNet is just a protocol on top of CAN.) Anyway, the following hardware is on the stack: Kontron MOPSPM104 with a 1GHz Intel Celeron processor ConnectTech FlashDrive/104 4GB Industrial Temp (-40 to +85 C) Woodhead (Molex) PC104DVNIO DeviceNet card A run of the mill 104 power supply The Kontron Board offers two serial ports, one VGA out, and two USB ports. The DeviceNet card is an ISA card. Because of this (per the User's Guide for the Kontron Board), I have manually set the IRQs in the BIOS to be appropriately configured, and turned off ACPI in both the BIOS and passed the appropriate flag in GRUB. I've installed Ubuntu 8.04 desktop, 32 bit. The problem that I'm having is that, from time to time, the entire 104 stack locks up. This only seems to happen in two cases, both of which we're running GNOME. We have a custom application that uses the DeviceNet card, and the system will lock up, or (more frequently) when we're running Firefox and either surfing for some information or trying to test it - typically by streaming video from a IP-camera. The reason I ask this questions is I cannot determine the root cause of this lockup. The IRQs appear to correctly configured in the BIOS and as the Kernel sees them, and nothing is logged to dmesg. If you all could help me determine the root cause of this lockup, I would greatly appreciate it. Thanks.

    Read the article

  • One dns server in different subnets

    - by hofmeister
    I have installed a small Linux server; the server is in a different subnet as the internet hosts. I added a route to my nat router to create a connection between both subnets. In both subnets I use an extra dhcp Server. Subnet A: 192.168.0.0/26 Subnet B: 192.168.1.0/26 Router: 192.168.0.1, Server in A: 192.168.0.62, Server in B: 192.168.1.62 internet ____ nat router ___ (Sub A)___ internet hosts | |____(Sub B)___ other hosts I could ping every host. Also the hosts which are connected to the subnet b, has internet connection. But sadly I have a problem with the dns server. I use the dnsServer from my nat router, I set the dns Server for subnet b to the ip 192.168.0.1, but every dns entries are equal with the hostname from my linux server. Example if the hostname from the server is test Test 192.168.0.62 //Server subnet a Test-2 192.168.1.62 //Server subnet b Test-2-2 192.168.1.1 //host a Test-2-2-2 192.168.1.2 //host b Any idea what went wrong? The internet dns resolution works fine.

    Read the article

  • Postgres pgpass windows - not working

    - by Scott
    DB: Postgres 9.0 Client: Windows 7 Server Windows 2008, 64bit I'm trying to connect remotely to a postgres instance for purposes of performing a pg_dump to my local machine. Everything works from my client machine, except that I need to provide a password at the password prompt, and I'd ultimately like to batch this with a script. I've followed the instructions here: http://www.postgresql.org/docs/current/static/libpq-pgpass.html but it's not working. To recap, I've created a file on the client (and tried the server as well): C:/Users/postgres/AppData/postgresql/pgpass.conf, where postgresql is the db user. The file has one line with the following data: *:5432:*postgres:[mypassword] (also tried explicit ip/dbname values, all asterisks, and every combination in between. (I've also tried replacing each '*' with [localhost|myip] and [mydatabasename] respectively. From my client machine, I connect using: pg_dump -h [myip] -U postgres -w [mydbname] [mylocaldumpfile] I'm presuming that I need to provide the '-w' switch in order to ignore password prompt, at which point it should look in the AppData directory on the server. It just comes back with "connection to database failed: fe_sendauth: no password supplied. Any insights are appreciated. As a hack workaround, if there was a way I could tell the windows batch file on my client machine to inject the password at the postgres prompt, that would work as well. Thanks.

    Read the article

  • Simple way to set up port knocking on Linux?

    - by Ace Paus
    There are well known benefits of Port Knocking utilities when utilized in combination with firewall IP table modification. Port Knocking is best used to provide an additional layer of security over other tools such as the OpenSSH server. I would like some help setting it up on a ubuntu server. I looked at some port knocking implementations here: PORTKNOCKING - A system for stealthy authentication across closed ports. IMPLEMENTATIONS http://www.portknocking.org/view/implementations fwknop looked good. I found an Android client here. And fwknop (both client and server) is in the ubuntu repos. Unfortunately, setting it up (on the server) looks difficult. I do not have iptables set up. My proficiency with iptables is limited (but I understand the basics). I'm looking for a series of simple steps to set it up. I only want to open the SSH port in response to a valid knock. Alternatively, I would consider other port knocking implementations, if they are much simpler to set up and the desired Linux and Android clients are available.

    Read the article

  • How do you make Google's interface always be in your chosen language?

    - by Michael Wolf
    Google's interface and search results don't always appear in my preferred language, English. I'm located in Mexico City and, although I generally have no problem with Spanish, I would prefer search results in English most of the time. (The exception is when I'm using search terms in Spanish.) I'd also prefer the interface to be in English, but that's far less important to me than search results. Google looks at your IP to decide where you're coming from and thus what language to present results in. So, when I type www.google.com into the URL bar, it redirects me to www.google.com.mx. Is there a way to force Google to use one language all the time? Here are some things I've done and tried: 0) I have a Google account, and I've configured it such that it should know that English is my preferred language. I don't often explicitly log out of Google, so generally Google knows I'm me and my preferences when I access its services. 1) I've configured my browser to ask for pages in English. Very few sites support this feature at all; Google isn't one of them. 2) From www.google.com.mx, I can click on "Google.com in English". This works until, I think, I close the browser. 2a) From www.google.com.mx, I can go into account configuration, which is English. From then on, everything's in English. 3) I can append &hl=en (Human Language = English) to the end of the URLs of result pages. 2, 2a, and 3 all "work", but they're all mildly annoying. I'd rather avoid them if I could. (At the risk of stating the obvious, English and Spanish are the languages I'm dealing with, but I imagine that, say, a francophone using Google from Korea would run into basically the same issue.)

    Read the article

  • Openvpn - stuck on Connecting

    - by user224277
    I've got a problem with openvpn server... every time when I trying to connect to the VPN , I am getting a window with login and password box, so I typed my login and password (login = Common Name (user1) and password is from a challenge password from the client certificate. Logs : Jun 7 17:03:05 test ovpn-openvpn[5618]: Authenticate/Decrypt packet error: packet HMAC authentication failed Jun 7 17:03:05 test ovpn-openvpn[5618]: TLS Error: incoming packet authentication failed from [AF_INET]80.**.**.***:54179 Client.ovpn : client #dev tap dev tun #proto tcp proto udp remote [Server IP] 1194 resolv-retry infinite nobind persist-key persist-tun ca ca.crt cert user1.crt key user1.key <tls-auth> -----BEGIN OpenVPN Static key V1----- d1e0... -----END OpenVPN Static key V1----- </tls-auth> ns-cert-type server cipher AES-256-CBC comp-lzo yes verb 0 mute 20 My openvpn.conf : port 1194 #proto tcp proto udp #dev tap dev tun #dev-node MyTap ca /etc/openvpn/keys/ca.crt cert /etc/openvpn/keys/VPN.crt key /etc/openvpn/keys/VPN.key dh /etc/openvpn/keys/dh2048.pem server 10.8.0.0 255.255.255.0 ifconfig-pool-persist ipp.txt #push „route 192.168.5.0 255.255.255.0? #push „route 192.168.10.0 255.255.255.0? keepalive 10 120 tls-auth /etc/openvpn/keys/ta.key 0 #cipher BF-CBC # Blowfish #cipher AES-128-CBC # AES #cipher DES-EDE3-CBC # Triple-DES comp-lzo #max-clients 100 #user nobody #group nogroup persist-key persist-tun status openvpn-status.log #log openvpn.log #log-append openvpn.log verb 3 sysctl : net.ipv4.ip_forward=1

    Read the article

  • Postgres pgpass windows - not working

    - by Scott
    DB: Postgres 9.0 Client: Windows 7 Server Windows 2008, 64bit I'm trying to connect remotely to a postgres instance for purposes of performing a pg_dump to my local machine. Everything works from my client machine, except that I need to provide a password at the password prompt, and I'd ultimately like to batch this with a script. I've followed the instructions here: http://www.postgresql.org/docs/current/static/libpq-pgpass.html but it's not working. To recap, I've created a file on the client (and tried the server as well): C:/Users/postgres/AppData/postgresql/pgpass.conf, where postgresql is the db user. The file has one line with the following data: *:5432:*postgres:[mypassword] (also tried explicit ip/dbname values, all asterisks, and every combination in between. (I've also tried replacing each '*' with [localhost|myip] and [mydatabasename] respectively. From my client machine, I connect using: pg_dump -h [myip] -U postgres -w [mydbname] [mylocaldumpfile] I'm presuming that I need to provide the '-w' switch in order to ignore password prompt, at which point it should look in the AppData directory on the server. It just comes back with "connection to database failed: fe_sendauth: no password supplied. Any insights are appreciated. As a hack workaround, if there was a way I could tell the windows batch file on my client machine to inject the password at the postgres prompt, that would work as well. Thanks.

    Read the article

  • Ubuntu networking issue: two specific machines cannot browse web while connected to network at the same time.

    - by jensendarren
    I have setup a secure wireless network which works very well except for two laptops running Ubuntu 10.10 that can't access the Internet via a browser at the same time. They can both ping sites, wget sites, use skype but when using a browser the page never loads (in Firefox the status bar just sits there saying "Connecting" until it times out.) Here is what we have tried so far (nothing has fixed this issue): OpenDNS Restart networking services Using wired connection rather than wireless Removing all other nodes from the network except the two machines that have this issue Swapped out the router Factory reset the router Reformatted one of the machines and re-installed Ubuntu 10.10 Other things that we have checked: The two machines can connect simultaneously without any issues to other wireless networks in different locations (say in an Internet Cafe or another office) The two machines have unique IP addresses The two machines have unique MAC addresses The two machines can communicate on the network using Skype, wget, ping etc We are not using a proxy on either machine FYI: I have attached output from wireshark. For the test we turned both machines on and pointed them both to the same website. The content loaded on one and not the other. Here is the output from wireshark- (speedyshare.com/files/26228631/machine_output_1 && speedyshare.com/files/26228649/machine2). As you can see the first one worked, the second one didn't. I don't fully understand the output and would appreciate if someone could shed some light on what might be causing this and how we can fix it! Many thanks! Darren

    Read the article

  • Internet Problem: Wireless connected but no connection to internet

    - by Josh K
    Hey i have a interesting network setup on a laptop here and for some reason the internet isnt working. I am connected to a secure network via wireless router and taskbar says i am connected and with good signal strength but in my internet browser i cant connect to any websites, the error is: This webpage is not available. (Chrome) I am using Chrome, but websites dont work on IE either. Heres a little background on the setup i have. I have a Ethernet connected to the laptop with a static ip, and then i have the wireless setup with DHCP enabled. I am using the ethernet to connect to the network (for remote desktop) but the wireless for internet (to avoid the network firewalls). this set up has worked fine for a few months, but i cant figure out what is going on now. Might be worth it to note it is a Lenovo Thinkpad and i just uninstalled ThinkVantage Access Connections (as it was giving me ample problems prior to this one, which i consider a step up) Tried repairing connection as well, let me know if you guys have any ideas please! EDIT: Solved-Dead Modem in the server room.... Sorry guys didn't have access to that myself

    Read the article

  • What are problems and pitfalls with a public facing Active Directory

    - by Ralph Shillington
    The situation that i'm faced with is this: We plan on using a number of server applications hosted on Amazon EC2 machines, mainly Microsoft Team Foundation Server. These services rely heavily on Active Directory. Since our servers are in the Amazon cloud it should go without saying (but I will) that all our users are remote. It seems that we can't setup VPN on our EC2 instance -- so the users will have to join the domain, directly over the internet then they'll be able to authenticate and once authenticated, use that token for accessing resources such as TFS. on the DC instance, I can shut down all ports, except those needed for joining/authenicating to the domain. I can also filter the IP on that machine to just those address that we are expecting our users to be at (it's a small group) On the web based application servers, I imagine all we need to open is port 80 (or 8080 in the case of TFS) One of the problems that I'm faced with is what domain name to use for this Active directory. Should I go with "ourDomainName.com" or "OurDomainName.local" If I choose the latter, does that not mean that I'll have to get all our users to change their DNS address to point to our server, so it can resolve the domain name (I guess I could also distribute a host file) Perhaps there is another alternative that I'm completely missing.

    Read the article

  • iSCSI performance questions

    - by RyanLambert
    Hi everyone, apologies for the long-winded post in advance... Attempting to troubleshoot some iSCSI sluggishness on a brand new vSphere deployment (still in test). Layout is as such: 3 VSphere hosts, each with 2x 10GB NICs plugged into a pair of Nexus 5020s with a 10gig back-to-back between them. NICs are port-channeled in an active/active redundant fashion (using vPC-mac pinning for those of you familiar with N1KV) Both NICs carry service console, vmotion, iSCSI, and guest traffic. iSCSI is on a single subnet/single VLAN that is not routed through our IP network (strictly layer2) Had this been a 1gig deployment, we probably would have split the iSCSI traffic off onto separate NICs, but the price/port gets rather ridiculous when you start throwing 4+ NICs to a server in a 10gigabit infrastructure, and I'm not really convinced it's necessary. Open to dialogue/tech facts re: this, though. At this point even a single VM guest will boot slowly to iSCSI storage (EMC CX4 on the same Nexus 5020 10gig switches), and restores of VMs from iSCSI take about twice as long as we'd expect them to. Our server folks mentioned that if we split the iSCSI off onto its own NIC, performance seems significantly better. From a network perspective, I've run through the variables I can think of (port configuration errors, MTU problems, congestion etc.) and I'm coming up dry. There really is no other traffic on these hosts other than the very specific test being performed at the time. Important thing to note is that guest traffic works just fine... it seems storage is the only thing affected by whatever gremlin exists. Concluding that we're not 'overutilizing' the network infrastructure since we're doing hardly anything, I'm just looking for some helpful tips/ideas we can use to resolve this... preferably without hurling extra 10gig NICs that are going to sit around 10% utilization while we've got 70+% left on our others.

    Read the article

  • Deploying a Django application in a virtual Ubuntu Server

    - by mfsaint
    I have a virtualbox machine running Ubuntu Server 10.04LTS. My intention is to this machine to work like a VPS, this way I can learn and prepare for when I get a VPS service. Apache+mod_wsgi for deploying the Django app seems the right choice to me. I have the domain (marianofalcon.com.ar) but nothing else, no DNS. The problem is that I'm pretty lost with all the deployment stuff. I know how to configure mod_wsgi(with the django.wsgi file) and apache(creating a VirtualHost). Something is missing and I don't know what it is. I think that I lack networking skills ant that's the big problem. Trying to host the app on a virtualbox adds some difficulty because I don't know well what IP to use. This is what I've got: file placed at: /etc/apache2/sites-available: NameVirtualHost *:80 <VirtualHost *:80> ServerAdmin [email protected] ServerName www.my-domain.com ServerAlias my-domain.com Alias /media /path/to/my/project/media DocumentRoot /path/to/my/project WSGIScriptAlias / /path/to/your/project/apache/django.wsgi ErrorLog /var/log/apache2/error.log LogLevel warn CustomLog /var/log/apache2/access.log combined </VirtualHost> django.wsgi file: import os, sys wsgi_dir = os.path.abspath(os.path.dirname(__file__)) project_dir = os.path.dirname(wsgi_dir) sys.path.append(project_dir) project_settings = os.path.join(project_dir,'settings') os.environ['DJANGO_SETTINGS_MODULE'] = 'myproject.settings' import django.core.handlers.wsgi application = django.core.handlers.wsgi.WSGIHandler()

    Read the article

  • Production deployment to EC2 with minimal downtime

    - by jensendarren
    I have a simple web application deployed on a large instance with EC2. I now want to deploy the latest code to this server but I want to do this in a way which minimizes downtime and is a smooth as possible for the end user. Here is my plan: Fire up another large instance Install all the software layers on that instance Restore and attach an EBS drive to the instance Deploy our latest production ready code on the new instance Run all tests (including manual testing of the application) (If tests pass) Put a "Site Under Maintenance" notice on the live site. Backup the EBS instance on the live site Detach the EBS instance from the new server and replace with the latest backup Use ec2-associate-address to move the IP address to the new instance Sit back and wait for traffic to start flowing though the new instance Terminate the old instance Does this seem like a good strategy? Are there any tutorials or books that might cover this topic? I have already read Cloud Application Architectures by George Reese, which is an excellent book, but does not cover deployment. Additionally, I know that there are tools that can help with this like RightScale or enStratus which I will use when I start using more than one instance.

    Read the article

  • Printer spooler service stop running when sent print job

    - by Hanan N.
    Every time i am sending a print job to the printer, i am don't get any response from the printer, and at the printer job list at the status of the job, i see that there was an Error, but it don't give me any clue on what could be the problem. After some investigation i found that every time that i send the print job to the printer the printer spooler service stops to run, then after a second or two it start again (i think that this behavior is related to the printer spooler settings to rerun it self after it stops). Things that i have tried so far: Remove and Install again the Driver. After removing the driver, i have removed the unnecessary registry keys according to this article from Microsoft, these are: Rename all files and folders in: c:\windows\system32\spool\drivers\w32x86 Remove anything but Drivers Print and Processors: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Print\Environment\Windows NT x86 Remove anything in here: HKEY_LOCAL_MACHINE\SYSTEM\CurrentControlSet\Control\Print\Monitors but: BJ Language Monitor Local Port Microsoft Document Imaging Writer Monitor Microsoft Shared Fax Monitor Standard TCP/IP Port USB Monitor WSD Port Disconnect and Reconnect the Printer. Clean the computer from Viruses & Spywares. Currently i am stuck, i have no more things to try, if anybody know about any kind of solution please let me know about it. Since i am want to keep this post as general problem that relate to the printer spooler, and not just my particular problem, i didn't included inside the windows version & the printer model, they are (although i think that it isn't relate just for that particular model): Windows 7 32bit, HP Officejet 4500 G510g-m (connect to the computer via USB). Thanks.

    Read the article

  • Connecting to unsecured wireless network

    - by Sanchez
    I would like to know what information is public and can be intercepted in a non-open, but unsecured wireless network. Moreover, is there anything I can do to make it more "secure", other than using https connection whenever possible. In more details, I recently discovered (with surprise) that the wireless network in my school is actually unsecured. Although not everyone can connect to it (you need a student ID), I am told that certain softwares like Wireshark would be able to intercept the data. Since I have been using the network for all private purposes (email, facebook etc), I do feel quite insecure now and would like to understand the situation a bit better. I installed Wireshark and tried to play with it but all I can see are something alien to me. In any case, all I see seems to come directly/indirectly from my IP address, and I have long thought that usually different computers in the same wireless network would be assigned different addresses. Am I wrong? If not, then I feel very confused about what information is actually being captured (potentially by other users in the network, since I don't think I could capture activities of others in the same network anyway), and whether it's safe to use the network at all. (Gambling on others in the same network showing good behaviour is apparently not an option.) Thank you.

    Read the article

< Previous Page | 614 615 616 617 618 619 620 621 622 623 624 625  | Next Page >