Search Results

Search found 21644 results on 866 pages for 'connection speed'.

Page 621/866 | < Previous Page | 617 618 619 620 621 622 623 624 625 626 627 628  | Next Page >

• What is the simplest way to confirm or to disprove that Virtual Box virtual machines support GRE protocol

  - by mbaitoff

  It is stated in VirtualBox manual (chapter 6) that VM network interfaces in "NAT" mode do not support GRE protocol. I'm currently trying to setup a pair of VMs as pptp server and client which would communicate via VM's network interfaces in "INTERNAL NETWORK" mode. I set up modern Linux OSes with pptp software on both machines and made some basic pptp configuration. However, I fail to connect the client to the server - server reports a failure when writing to GRE socket. I now need a quick proof of principal ability to use the GRE protocol between VirtualBox VMs over a network in "INTERNAL" mode, such as a several-line .c program that would try to open/send/receive/close a GRE protocol connection, or like a specific lightweight tool to diagnose the GRE availability. Any suggestions?

  Read the article

• Root certificate authority works windows/linux but not mac osx - (malformed)

  - by AKwhat

  I have created a self-signed root certificate authority which if I install onto windows, linux, or even using the certificate store in firefox (windows/linux/macosx) will work perfectly with my terminating proxy. I have installed it into the system keychain and I have set the certificate to always trust. Within the chrome browser details it says "The certificate that Chrome received during this connection attempt is not formatted correctly, so Chrome cannot use it to protect your information. Error type: Malformed certificate" I used this code to create the certificate: openssl genrsa -des3 -passout pass:***** -out private/server.key 4096 openssl req -batch -passin pass:***** -new -x509 -nodes -sha1 -days 3600 -key private/server.key -out server.crt -config ../openssl.cnf If the issue is NOT that it is malformed (because it works everywhere else) then what else could it be? Am I installing it incorrectly? Update I tried changing the certificate attributes, but to no avail: openssl genrsa -des -passout pass:***** -out private/server.key 2048 openssl req -batch -passin pass:***** -new -x509 -nodes -sha256 -days 3600 -key private/server.key -out server.crt -config ../openssl.cnf

  Read the article

• Monitor turns off about 1 second after turning it on

  - by r0ca

  Hi all! I have a hardware issue with some of the LCD monitors we have in our office. My problems is not related to video cards or anything else with the computer itself. I have 2 Dell 17" LCD screens that goes off (blank) after 1 or 2 seconds. The light remains green so it's not idling or sleeping. Just this morning, I had to replace one that goes off on 2 workstations and also on my laptop. Nothing to do with it. I tried the VGA and DVI connection w/out luck. I strongly think that this is something with a capacitor or something inside the screen but I can't figure out what it is... Is anybody heard of that kind of issue before? Regards, David.

  Read the article

• After virus, Chrome & Internet Explorer won't connect to the internet, but Firefox works fine.

  - by Zack

  I cannot connect to the internet with Chrome or Internet Explorer. Firefox works fine. It seems it happens when I was infected by a "Trojan Horse Generic 17.BWIK", "Trojan Horse SHeur.UHL" and "Fake_Antispyware.FAH". I have removed the threats using AVG anti-virus security. I got Firefox working, but Chrome and IE still cannot connect. I do not want to loose Chrome History so re-setting would be my last option and uninstall and install will be out of the question. Is there a way around this? I am using XP Pro on a desktop and DSL connection.

  Read the article

• LinkSys WRT54GL + AM200 in half-bridge mode - UK setup guide recommendations?

  - by Peter Mounce

  I am basically looking for a good guide on how to set up my home network with this set of hardware. I need: Dynamic DNS Firewall + port-forwarding VPN Wake-on-LAN from outside firewall VOIP would be nice QoS would be nice (make torrents take lower priority to other services when those other services are happening) DHCP Wireless + WPA2 security Ability to play multiplayer computer games I am not a networking or computing neophyte, but the last time I messed with network gear was a few years ago, so am needing to dust off knowledge I kinda half have. I have read that I should be wanting to set up the AM200 in half-bridge mode, so that the WRT54GL gets the WAN IP - this sounds like a good idea, but I'd still like to be advised. I have read that the dd-wrt firmware will meet my needs (though I gather I'll need the vpn-specific build, which appears to preclude supporting VOIP), but I'm not wedded to using it. I live in the UK and my ISP supplies me with: a block of 8 static IPs, of which 5 are usable to me a PPPoA ADSL2+ connection

  Read the article

• LinkSys WRT54GL + AM200 in half-bridge mode - UK setup guide recommendations?

  - by Peter Mounce

  Crossposted from here I am basically looking for a good guide on how to set up my home network with this set of hardware. I need: Dynamic DNS Firewall + port-forwarding VPN Wake-on-LAN from outside firewall VOIP would be nice QoS would be nice (make torrents take lower priority to other services when those other services are happening) DHCP Wireless + WPA2 security Ability to play multiplayer computer games I am not a networking or computing neophyte, but the last time I messed with network gear was a few years ago, so am needing to dust off knowledge I kinda half have. I have read that I should be wanting to set up the AM200 in half-bridge mode, so that the WRT54GL gets the WAN IP - this sounds like a good idea, but I'd still like to be advised. I have read that the dd-wrt firmware will meet my needs (though I gather I'll need the vpn-specific build, which appears to preclude supporting VOIP), but I'm not wedded to using it. I live in the UK and my ISP supplies me with: a block of 8 static IPs, of which 5 are usable to me a PPPoA ADSL2+ connection

  Read the article

• Network on linux server is periodically down

  - by Fabian

  I have an old server running Fedora 4 that occasionally just stops responding via network for about an hour. This happens 1-2 times a week. Also no connection from the server itself to any other computer on the network is possible when it happens. The network settings and routes look fine. There are no unusual log messages and no unusual processes running at that time. If I restart the network or just do an ifconfig eth0 down & ifconfig eth0 up it works fine afterwards. I know that the server should be updated to a currently supported OS, but that is not really an easy option right now. Any ideas on how I could diagnose and fix that problem?

  Read the article

• NAT Error Message - Usage limit exceeded

  - by Kato

  Trying to configure a port to use for Vuze. Using the NAT/server port test, I was getting a message saying the connection timed out, the port was probably closed. I went back and made sure to open the specific port on my router, firewall, etc, but now I'm getting "NAT Error - Usage limit exceeded (173.32.41.24:0). I'm on a mac pro running leopard, trial versions of intego netbarrier and virusbarrier. Network utilities and netbarrier both claim the port is open. I've tested a bunch of other ports, but all give the same message.

  Read the article

• Oracle Worldwide Product Translation Group and Applications User Experience Working Together

  - by ultan o'broin

  The Applications User Experience (UX) Mobile team has been extending its ethnographic research to even more countries. Recently, the team conducted research in Sweden, and I am pleased to say I made the connection for the UX team with the Oracle's Worldwide Translation Product Group (WPTG) local (that is, in-country) language specialists. It struck me that WPTG's local market knowledge and insight that we heard about at an Oracle Usability Advisory Board meeting in the UK in 2011 would be very valuable to the UX efforts while, at the same time, UX could afford WPTG an opportunity to understand our design and development direction so that linguistic resources (terminology, style guides, translatability guidelines, and so on) for any translation of our mobile solutions could be prepared in advance. Brent White of the Mobile UX team takes notes as ethnography participant Capri Norman uses mobile technology to work in Stockholm. Pic credit: Oracle Applications UX. The UX team acknowledges Capri's kind permission to use this image. I'm told by Brent White of the Mobile UX team that the co-operation was a big success.  A WPTG Swedish language specialist joined a couple of ethnographic sessions, taking great notes and turning them around very fast for the UX team. And of course, a great local insight into Swedish culture and ways of working was provided too, along with some nice socializing!  More research in more countries is planned. Watch out for future blog posts and other communications about this great co-operation worldwide.

  Read the article

• How to split audio into multiple channels from optical S/PDIF or 1/8"?

  - by Josh M.

  I have a motherboard which has an optical S/PDIF output or 1/8". I'd like to "split" that signal into the appropriate channels so that I can then connect that to the wires behind my car's headunit which, in turn, run to the amp. The factory Bose amp just takes a single connector with a million wires running out of it, so that's why I would need to separate the signal into separate channels. On the other end there are four RCA connectors: front left, front right, rear left, rear right. The sub-woofer signal does not require an additional connection. Edit: Revised to include S/PDIF or 1/8".

  Read the article

• Drivers for Atheros AR928X?

  - by Pato7

  I am new in Ubuntu and I had a big trouble with wifi. My ubuntu 12.10 doesn't detect my wifi card and I can't toggle the "activate wireless" option on the tasks bar (it is grey). I searched for drivers to make it work, but nothing worked for me. Can anyone give me a hand? Many thanks in advanced! lspci output 00:00.0 Host bridge: Intel Corporation Mobile 4 Series Chipset Memory Controller Hub (rev 07) 00:01.0 PCI bridge: Intel Corporation Mobile 4 Series Chipset PCI Express Graphics Port (rev 07) 00:1a.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #4 (rev 03) 00:1a.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #5 (rev 03) 00:1a.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #6 (rev 03) 00:1a.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #2 (rev 03) 00:1b.0 Audio device: Intel Corporation 82801I (ICH9 Family) HD Audio Controller (rev 03) 00:1c.0 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 1 (rev 03) 00:1c.1 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 2 (rev 03) 00:1c.2 PCI bridge: Intel Corporation 82801I (ICH9 Family) PCI Express Port 3 (rev 03) 00:1d.0 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #1 (rev 03) 00:1d.1 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #2 (rev 03) 00:1d.2 USB controller: Intel Corporation 82801I (ICH9 Family) USB UHCI Controller #3 (rev 03) 00:1d.7 USB controller: Intel Corporation 82801I (ICH9 Family) USB2 EHCI Controller #1 (rev 03) 00:1e.0 PCI bridge: Intel Corporation 82801 Mobile PCI Bridge (rev 93) 00:1f.0 ISA bridge: Intel Corporation ICH9M LPC Interface Controller (rev 03) 00:1f.2 SATA controller: Intel Corporation 82801IBM/IEM (ICH9M/ICH9M-E) 4 port SATA Controller [AHCI mode] (rev 03) 00:1f.3 SMBus: Intel Corporation 82801I (ICH9 Family) SMBus Controller (rev 03) 01:00.0 VGA compatible controller: Advanced Micro Devices [AMD] nee ATI RV710 [Mobility Radeon HD 4500/5100 Series] 01:00.1 Audio device: Advanced Micro Devices [AMD] nee ATI RV710/730 HDMI Audio [Radeon HD 4000 series] 02:00.0 Ethernet controller: Marvell Technology Group Ltd. 88E8057 PCI-E Gigabit Ethernet Controller (rev 10) 03:00.0 Network controller: Atheros Communications Inc. AR928X Wireless Network Adapter (PCI-Express) (rev 01) 0c:03.0 FireWire (IEEE 1394): Ricoh Co Ltd R5C832 IEEE 1394 Controller (rev 05) 0c:03.1 SD Host controller: Ricoh Co Ltd R5C822 SD/SDIO/MMC/MS/MSPro Host Adapter (rev 22) 0c:03.2 System peripheral: Ricoh Co Ltd R5C592 Memory Stick Bus Host Adapter (rev 12) lshw -c network output *-network descripción: Ethernet interface producto: 88E8057 PCI-E Gigabit Ethernet Controller fabricante: Marvell Technology Group Ltd. id físico: 0 información del bus: pci@0000:02:00.0 nombre lógico: eth0 versión: 10 serie: 00:24:be:83:b2:4f tamaño: 100Mbit/s capacidad: 1Gbit/s anchura: 64 bits reloj: 33MHz capacidades: pm msi pciexpress bus_master cap_list rom ethernet physical tp 10bt 10bt-fd 100bt 100bt-fd 1000bt 1000bt-fd autonegotiation configuración: autonegotiation=on broadcast=yes driver=sky2 driverversion=1.30 duplex=full ip=192.168.1.123 latency=0 link=yes multicast=yes port=twisted pair speed=100Mbit/s recursos: irq:45 memoria:d3520000-d3523fff ioport:c000(size=256) memoria:d3500000-d351ffff *-network DESACTIVADO descripción: Interfaz inalámbrica producto: AR928X Wireless Network Adapter (PCI-Express) fabricante: Atheros Communications Inc. id físico: 0 información del bus: pci@0000:03:00.0 nombre lógico: wlan0 versión: 01 serie: 2c:81:58:e6:b6:03 anchura: 64 bits reloj: 33MHz capacidades: pm msi pciexpress msix bus_master cap_list ethernet physical wireless configuración: broadcast=yes driver=ath9k driverversion=3.5.0-18-generic firmware=N/A latency=0 link=no multicast=yes wireless=IEEE 802.11bgn recursos: irq:17 memoria:d2100000-d210ffff rfkill list all output 0: phy0: Wireless LAN Soft blocked: yes Hard blocked: yes 1: sony-wifi: Wireless LAN Soft blocked: yes Hard blocked: no

  Read the article

• Disable ALTQ for internal network traffic

  - by javanix

  I currently have a FreeBSD 8.2 media server set up on my LAN that I use to stream my music from. I also have an SSH login that I use to do file transfers to and from this server remotely. I would like to set up ALTQ (and have gotten this working) to limit my outgoing bandwidth from the server for SSH traffic. However, configuring ALTQ this way is also limiting my internal traffic (and thus interfering with my music streaming) since I am only using a single network interface. Can anyone show me how I would use PF and ALTQ to limit outgoing WAN traffic while allowing all internal LAN traffic to go through unhindered? ext_if="eth0" int_if="eth0" altq on eth0 cbq bandwidth 1Mb queue { std, ssh } queue std bandwidth 80% cbq(default) queue ssh bandwidth 20% cbq(ecn) pass out on eth0 proto tcp to port 22 queue ssh eth0 is my LAN interface, my total WAN bandwidth on my cable connection is 1Mb/s, and my internal network is 10/100.

  Read the article

• Connecting to a computer using Remote Desktop does not work first time

  - by dev

  Hi all, I'm having a weird sort of problem with Remote desktop and that too, only on one machine. If I boot up this machine, and then try to Remote desktop into it, it does not work.( I get the following error: The client could not connect to the remote computer. Remote connections might not be enabled or the computer might be too busy to accept new connections. It is also possible that network problems are preventing your connection. Please try connecting again later. If the problem continues to occur, contact your administrator. ) But if I physically log into it & then log out, and then try to Remote desktop into it, it works flawlessly. The problematic machine is Xp 64 Bit, but other systems with Xp 64 Bit work fine. Any Ideas on how to solve this?

  Read the article

• Is there a way to stream wirelessly from a laptop to a TV?

  - by Robsta

  I heard of such a thing like a box or a media player such thing that can connect wirelessly to stream movies from my laptop? Is there such a thing that can do it? How is the latency on it? I have fast internet so that's not an issue, or is there such a box that connects with Bluetooth for better connection? I need these box to also be able to browse the internet because I'd like to stream movies from YouTube. I have heard of a thing called boxee, but is that what I'm looking for? I have windows 7 as my os, with an HDMI out and a GPU with a 555m. My laptop is powerful enough and my internet is 25mbps with a cap of 150GB. All i would really like to know is what this device is called? A media box?

  Read the article

• Windows 7: Server disappearing from Network window

  - by David Veeneman

  I am running a small (three computer) network on a Windows Server 2003 domain. All of the computers were just upgraded to Windows 7. Since the upgrade, the icon for the domain server periodically disappears from the Network window on all three computers. It doesn't happen at the same time on all computers--the icon typically disappears from one machine, but not the others. And it's not always the same computer. The network connection is still there--I can type \\myserver and get to the network shares. It's simply the icon that's disappearing. Has this happened to anyone else? Any suggestions for a fix? Thanks in advance.

  Read the article

• estimating size of reply HTTP headers

  - by Guanidene

  I am trying to download a file via a basic socket connection, using a HTTP GET request. So, I have to specify how many bytes of data coming in I have to read from the socket. However, I am having trouble deciding the amount of data (say, in bytes) the server would reply back with. I know that there is a "Content-Length" field in the reply sent by server, but that gives me the size of the actual data (without the http headers). Is there a way to get the exact size of HTTP headers sent by the server or an estimation is required? (I am doing this for downloading on a mobile network, where every bit of data matters in terms of time and money, so I don't wish to make an unnecessary larger estimate of the header size.)

  Read the article

• pinx 501 with print server - 10 licenses

  - by ra170

  I have pix 501 with only 10 licenses. I'm already approaching this limit, running 2 computers at home, 2 laptops, PS3, iphones, 2 web cams..not everthing is on all the time, but it's possible as I'm looking into adding a print server, so that I can print from anywhere in the house. So my question is, will the print server count as a connection towards the license? I think it will need default gateway, which in this case will be my pix 501. I've seen somewhere on some othee board saying, don't set default gateway in the print server to pix 501, but then how would that work? is there a work around? I don't need to print from VPN or from outside, just inside..

  Read the article

• Virtual PC "The page cannot be displayed" error connecting to iis7.5 site on Win7 host.

  - by stan

  I setup virtual pc with the Windows XP IE6 VHD to test a site on Windows 7 host. I created a loopback adapter connection on the host. I have several sites on IIS 7.5, I'm able to connect to all of them except one. And it's the site I need to test... I get "The page cannot be displayed" error. The site loads fine from the host(Windows 7). I've made sure the permissions match that of the other sites that do load. I've recreated the application in IIS manager. Does anyone know what the problem might be?

  Read the article

• Why is Google Chrome making these weird requests?

  - by mackenir

  I noticed that now and again, Chrome will make three requests to weird hostnames that arent resolved. For example: HEAD http://gtblynlsos/ HTTP/1.1 Host: gtblynlsos Proxy-Connection: keep-alive Content-Length: 0 User-Agent: Mozilla/5.0 (Windows; U; Windows NT 6.1; en-US) AppleWebKit/534.13 (KHTML, like Gecko) Chrome/9.0.597.107 Safari/534.13 Accept-Encoding: gzip,deflate,sdch Accept-Language: en-GB,en-US;q=0.8,en;q=0.6 Accept-Charset: ISO-8859-1,utf-8;q=0.7,*;q=0.3 Other example weird hostnames: http://nxibbjklov/ http://moheksgryj/ Has anyone else seen this? Any ideas what's going on? I have all Chrome extensions disabled.

  Read the article

• No Internet for Created VLan on Cisco CE500

  - by Jennifer

  I'm new here and also with networking but i can't set internet conection for some vlan created. I have a Cisco CE500 switch and created 4 vlans define by the roles in the switch. Vlan 2: Servers (role) (port 3-4) Vlan 3: Desktop (role) (port 5-8) Vlan 4: Guest (role) (port 9-12) Vlan 1 is default, Connect to the ADSL Modem/Router Port 2 assign to the Router Role (vlan 1) The switch is connected on port2 the ADSL Modem (DHCP) 192.168.2.254 The goal is: All Vlan should have internet connection. Vlan 2 and 3 should see each other but not Vlan 4 I can enter the switch CLI but dont know which command to enter. Thanks 4 ur time and replies Jennifer

  Read the article

• Why such a dramatic difference in wireless router max. simultaneous connections?

  - by Jez

  Recently, I've needed to look into buying a wireless router for a mission-critical system at work that will need to support quite a few simultaneous connections (potentially a few hundred laptops). One thing I've noticed is that there seems to be a dramatic difference between the max. simultaneous connections different routers can support; see this page for example - anything from 32 to 35,000! Why is there this degree of difference? You'd have thought that if we know how to make routers that can handle thousands of connections, we wouldn't be making stuff that's limited to a pathetic 32 anymore. Is it a firmware thing? A hardware thing? Are low-end manufacturers purposely putting low arbitrary connection limits in so people can be "encouraged" to pay more for high-end routers?

  Read the article

• Reporting available RDP sessions

  - by Sergei

  Hi All Default Windows 2003 Server has two RDP sessions available.If all of them are taken by someone else you will only be notified about it after providing your credentials. This seems like a waste of time especially in our environment where we share a lot of development server. Could a message be given as soon as you open the connection window if the connections are taken up? We can use qwinsta based script to check sessions before logon but it's still takes time. Is there a feature to do what I am asking for?

  Read the article

• How do I run a batch file async using PSExec?

  - by Paul Mrozowski

  I have a batch file I run that, among other things, reset's the NICs in the machine. I have some watchdog software running on another machine that monitors the first one. I'd like to run this batch file using PSExec when it detects certain types of failures. The problem I'm having is that since the batch file reset's the NIC's it kills the connection PSExec has (I'm OK with that). The real issue is that when PSExec dies the batch file stops running (leaving the NIC's disabled). I've tried using the -i option with PSExec with no luck. Any ideas about basically just fire off the batch file and NOT have it stop when PSExec is disconnected?

  Read the article

• Can't start firewall or automatic updates in Windows XP

  - by Chris Porter

  On a friends laptop following some viruses infestations there is a problem in starting the Windows firewall. The error is: Could not start the Windows Firewall/Internet Connection Sharing(ICS) service on Local Computer. Error 2: The system cannot find the file specified When attempting to turn on automatic updates in the security centre, the message is: We're sorry. The Security Center could not change your Automatic Updates settings. To try changing these settings yourself, go to System in Control Panel. On the Automtic Updates tab, select Automatic (recommended), and then click OK. All the options under "Automatic Updates" are greyed out. I've tried the suggestions below and many others: http://windowsxp.mvps.org/sharedaccess.htm http://support.Microsoft.com/kb/892199 http://windowsxp.mvps.org/repairwmi.htm I can't do a repair install because the installer doesn't detect existing versions. It's XP pro service pack 3.

  Read the article

• windows cache not working as it should?

  - by piotrektt

  I run windows 2012 server with data center. The setup is with 60GB of RAM. I have one file shared on VHD and when I copy this file locally the RAM cache is all used up but when multiple computers connect to the share it the cache is not used. The network is 8Gb. The whole network is around 200 computers that need to read that one file but on this setup only 10 connection kills the server. Is there any way to check what is going on? What other solution can I use to manage cache in windows?

  Read the article

< Previous Page | 617 618 619 620 621 622 623 624 625 626 627 628  | Next Page >