Search Results

Search found 21097 results on 844 pages for 'check snmp'.

Page 622/844 | < Previous Page | 618 619 620 621 622 623 624 625 626 627 628 629  | Next Page >

• Laptop will not boot

  - by WillumMaguire

  This is a dell studio 1558 laptop. Now, something is wrong with the charger that it won't charge the laptop, but the laptop can turn on and operate properly as long as it is attached. It has been like this for a while, but it's not the problem. My problem is that as of yesterday, It takes several minutes to get past the "dell" startup logo (where is says "f2 setup" and "f12 boot options"). After it gets past, it beeps as normal to tell me about the charger and gives me the f2/f12 options and f1 to continue as normal. I can press f12 to get into boot options and load into my live USB BackTrack 5 ISO, but after "startx" it just stays at a black screen. I can also access BIOS setup, but see nothing that would help the problem. When I boot to the HDD, it gives me this Intel UNDI, PXE-2.1 (build 083) Realktek PCIe GBE Family Controller Series V.2.29 (06/30/09) PXE-E61: Media test failure, check cable PXE-M0F: Exiting PXE ROM Operating System not found Also, pressing f8 gives me the same results as booting as normal. It is running Windows 7 Ultimate, dual-core Intel i3 @ 2.27ghz and 4gb RAM. I think there is an issue with the HDD, as the "Operating System not found" would lead me to believe. Is this a fixable problem?

  Read the article

• Windows 7 machine, can't connect remotely until after ping

  - by rjohnston

  I have a Windows 7 (Home Premium) machine that doubles as a media centre and subversion server. There's a couple of problems with this setup, when connecting to the server from an XP (SP3) machine: Firstly, the machine won't respond to it's machine name until after it's IP address has been pinged. Here's an example: Microsoft Windows XP [Version 5.1.2600] (C) Copyright 1985-2001 Microsoft Corp. C:\Documents and Settings\Rob>ping damascus Ping request could not find host damascus. Please check the name and try again. C:\Documents and Settings\Rob>ping 192.168.1.17 Pinging 192.168.1.17 with 32 bytes of data: Reply from 192.168.1.17: bytes=32 time=2ms TTL=128 ... Ping statistics for 192.168.1.17: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 1ms, Maximum = 2ms, Average = 1ms C:\Documents and Settings\Rob>ping damascus Pinging damascus [192.168.1.17] with 32 bytes of data: Reply from 192.168.1.17: bytes=32 time<1ms TTL=128 .... Ping statistics for 192.168.1.17: Packets: Sent = 4, Received = 4, Lost = 0 (0% loss), Approximate round trip times in milli-seconds: Minimum = 0ms, Maximum = 1ms, Average = 0ms C:\Documents and Settings\Rob> Likewise, subversion commands with either the machine name or IP address will fail until the machine's IP address is pinged. Occasionally, the machine won't respond to pings on it's IP address, it'll just come back with "Request timed out". The svn server is VisualSVN, if that helps... Any ideas?

  Read the article

• Checkpoint VPN-1 R60 and Windows 7 64 Bit Client

  - by Mohit

  As per my knowledge of checkpoint VPN-1. My company is using checkpoint VPN-1 R 60 ( I guess as I dont know how to check server version) Firewall(VPN Server). Now the problem is that I installed Windows 7 64 bit. But, after my research I found that there are not even one client (SecuRemote/SecuClient) for Win7 64 bit, when Firewall or server is R60. I thought of some open source solutions. Can you guys please suggest me some with the configuration required. As of now, I know the IP of the server. I know my username and password using which I connect and that is not my domain password. that i can confirm to you guys. I am not a network guy. I am more of a developer. But, I need some help in this.So, let me know if I can provide you more details. Please please i need urgent help on this.

  Read the article

• With Ubuntu 9.10, my DVD keeps spinning up

  - by Ken

  I have Ubuntu 9.10 on my Intel Mac Mini. When there's a DVD in the drive, and even if there's no program open at all (just looking at the desktop), every minute or so the disc spins up with a loud whirring noise, and I can hear it cranking the motor to seek across the disc. How do I find out what's causing this? And how can I make it stop? Thanks! EDIT: I straced nautilus, and saw nothing it's doing directly, even when the disc spins up. It does poll inotify regularly, but I don't know how to trace what it's watching, or if that's even how it receives disc-inserted notifications. It doesn't call inotify_add_watch when I insert a disc or mount it (or eject or umount), but it could be watching all of /dev already or something like that. Of course, a DVD is mounted read-only, so whether it's inotify or something else, it should never need to poll anything on that. And if it is inotify, it's happening in the kernel, and the kernel should really never need to poll a device it's mounted to check for notifications.

  Read the article

• Backup and Archive Strategy Question

  - by OneNerd

  I am having trouble finding a backup strategy for our code assets that 'just works' without any manual intervention. Goal is to have an off-site backup (a synchronized one) so that when we check-in files, create builds, etc. to the network drive, the entire folder structure is automatically synchronized and backed-up (in real time, or 1x per day) at some off-site location so if our office blows up, we don't lose all of our data. I have looked into some online backup services, but have not yet had any success. Some are quirky/buggy, others limit file size and/or kinds of files (which doesn't work well for developer files). Everything gets checked in and saved to a single server (on a Raid Mirror), so we just need to have a folder on that server backed up/synchronized to some off-site location. So my question is this. What are you using for your off-site backup strategy. What software, system, or service? Is there a be-all/end-all system of backing up your code assets that I just haven't found yet? Thanks

  Read the article

• Cannot start MySQL

  - by Mohamed Nour El-Din

  I used this command from shell to repair all Databases mysqlcheck -u root -p --auto-repair --check --optimize --all-databases and after that I restarted the server when it came back alive again I tried to open my vBulletin forum but I recived Database error message. and also tried to open phpMyAdmin but I received this error : #2002 - The server is not responding (or the local MySQL server's socket is not correctly configured). I checked the services list and found that the MySQL Service is not listed, so I tried to start it from shell I receive this error : Starting MySQL.Manager of pid-file quit without updating fi[FAILED] could anyone help me in that ? thanks in advance. update I found these lines in the log file 101101 01:36:01 mysqld started 101101 1:36:01 [Warning] Asked for 196608 thread stack, but got 126976 101101 1:36:01 [ERROR] /usr/sbin/mysqld: Table './mysql/user' is marked as crashed and last (automatic?) repair failed 101101 1:36:01 [ERROR] /usr/sbin/mysqld: Table './mysql/user' is marked as crashed and last (automatic?) repair failed 101101 1:36:01 [ERROR] Fatal error: Can't open and lock privilege tables: Table './mysql/user' is marked as crashed and last (automatic?) repair failed 101101 01:36:01 mysqld ended What should I do then ?

  Read the article

• VPN being blocked somewhere between either my BT2700HGV and DLink DFL-210

  - by Dom

  Hi, For some time I have been unable to get VPN working through my set up. I have a BT2700HGV Router (2 Wire Model) and as a firewall I have the Dlink DFL-210. You can't turn the firewall completely off on the BT2700HGV so I have it set to DMZplus mode for the Firewall. In theory this should then allow the VPN ports through. On the Firewall I have a series of rules set up and one is the pptp-allow rule which should allow access on the correct ports also. When I try to connect via VPN however the client machine gets an error 809. If I check the log on the Dlink firewall, I see this record: http://dl.dropbox.com/u/1041315/packetdrop.PNG The laptop I am testing the vpn with is connected directly to the BT2700HGV router and I am trying to VPN from it onto 81.138.86.217. I can't work out whether I have some sort of problem in the set up of the rules on my firewall or if the BT router (even though it's in DMZplus mode) is still blocking port 1723. I read somewhere that there where problems because BTs Openzone held onto this port for some reason. Any help would be greatly appreciated. If you need further screen shots or information then please let me know. I wasn't able to create new tags for the router and firewall name or insert the picture in as I am new to the forum. Dom :-)

  Read the article

• graphics performance better on battery?

  - by Scott Beeson

  Anyone have any idea why my laptop would perform (considerably) better while on battery than while plugged in? It's a Dell Latitude E6420 with Windows 8 Pro. I tried mirroring all the settings in the selected power plan from "On battery" to "Plugged In" and that didn't help. I then just restored the defaults for all power plans (balanced and high performance). I'm still seeing the same results. The best example where it is most noticeable (don't laugh) is Sim City Social in Chrome. I'm probably seeing a performance increase of 5x on battery versus plugged in. This is easily reproducible too. I'm very confused. Could it be caused by dust? The laptop isn't that old and there is no visible dust. I'm not going to take it apart to check the insides as it's a corporate laptop. Could it be overheating? Battery Sim City Social: 68 degrees max Civ V: 77 degrees max Charger Sim City Social: 68 Civ V: did not test See answer below... I'm retarded

  Read the article

• Windows 7 - mysteriously missing free HDD space

  - by sYnfo

  I have Windows7 installed on 50GB (Oops, it should have been 45GB, sorry) partition, and every now and then it gets full, and I have to resize that partition. I always thought it is quite normal. But it happened again today and this time, I'm sure it is not normal, because since last resizing (35GB 45GB) I did not install any new apps or whatever. Also, sum of sizes off all, including hidden & system, root folders and files is ~18GB, yet windows is indicating that all 50GB are used up... Any idea what is going on? EDIT: Great tools everyone! (SourceForge appears to be offline at the moment, I'll check WinDirStat later) Alas, non of them solved my problem just yet... Screenshot from SpaceSniffer: On the right there is some kind of "Unknows Space", any idea what that could be? EDIT2: After those two apps failing to help much I didn't expect it, but WinDirStat actually helped. It showed that those missing 27GB are in my Temp folder (Well, that should have been my first guess anyway). There I found hundreds of ~100MB files, named like HTT????.tmp. After some googling it appears to be a problem with ESET NOD32 antivirus and it's ThreatSense feature. Thank you all for help! :)

  Read the article

• Apache2: How to split out the SSL configuration?

  - by Klaas van Schelven

  In Apache2, I'd like to separately define my SSL-related stuff once, and in a separate file from the rest of the configuration. This is mostly a matter of taste, but it also allows me to include the rest of the configuration in my automatic deployment process. I.e.: current situation: # in file: 0000-ourdomain.com.conf (number needs to be low) <VirtualHost xx.xx.xx.xx:443> # SSL part SSLEngine on SSLCertificateFile ....crt SSLCACertificateFile ...pem SSLCertificateChainFile ...intermediate.pem SSLCertificateKeyFile ....wildcard.ourdomain.com.key SetEnvIf User-Agent ".*MSIE.*" nokeepalive ssl-unclean-shutdown ServerName www.ourdomain.com ServerAlias ourdomain.com # the actual configuration, as found for xx.xx.xx.xx:80, repeated </VirtualHost> I'd like # in file: 0000-ssl-stuff <VirtualHost xx.xx.xx.xx:443> # SSL part SSLEngine on SSLCertificateFile ....crt SSLCACertificateFile ...pem SSLCertificateChainFile ...intermediate.pem SSLCertificateKeyFile ....wildcard.ourdomain.com.key SetEnvIf User-Agent ".*MSIE.*" nokeepalive ssl-unclean-shutdown ServerName www.ourdomain.com ServerAlias ourdomain.com </VirtualHost> # in file: ourdomain.com.conf <VirtualHost xx.xx.xx.xx:443> # the actual configuration, as found for xx.xx.xx.xx:80, repeated </VirtualHost> Unfortunately, this does not seem to work. Apache SSL fails, though it does not give an error message at reload or syntax-check. My best found workaround is to us an Include directive from the 0000-ssl file. Many thanks!

  Read the article

• Linux Scheduler (not using all cores on multi-core machine) RHEL6

  - by User512

  I'm seeing strange behavior on one of my servers (running RHEL 6). There seems to be something wrong with the scheduler. Here's the test program I'm using: #include <stdio.h> #include <unistd.h> #include <stdlib.h> void RunClient(int i) { printf("Starting client %d\n", i); while (true) { } } int main(int argc, char** argv) { for (int i = 0; i < 4; ++i) { pid_t p_id = fork(); if (p_id == -1) { perror("fork"); } else if (p_id == 0) { RunClient(i); exit(0); } } return 0; } This machine has a lot more than 4 cores so we'd expect all processes to be running at 100%. When I check on top, the cpu usage varies. Sometimes it's split (100%, 33%, 33%, 33%), other times it's split (100%, 100%, 50%, 50%). When I try this test on another server of ours (running RHEL 5), there are no issues (it's 100%, 100%, 100%, 100%) as expected. What's causing this and how can I fix it? Thanks

  Read the article

• Driver issue for 7850 HD Diamond Windows 7

  - by Mr.Student

  I have an issue with windows 7 implementing the drivers ati provides for my 7850 HD Diamond video card. The video card is plugged in correctly to the PCIE 2.0 slots of my motherboard (p6t asus) with more then enough power. Fortunately the card works as I have my monitor plugged into the card itself and I can see just fine. However windows 7 does not replace the standard vga default microsoft driver with catalyst drivers that I've tried installing from online as well as the CD. Every time I install the drivers using Catalyst Install manager it always finishes with "Install complete(Warnings occured)". I then see the warnings it has which it instead reports that it successfully installed the SDK, Catalyst Install Manager, and HDMI/AUDIO packages. When I check my device manager after that, the display adapter still shows as standard vga and that its still using microsoft default display adapter. Now this current card is replacing an old card of mine which is the ATI 4890 HD which works beautifully. In fact for the old card to work, all I need to do is go to device manager and right click on standard vga - click update driver and windows 7 magically finds the correct driver to install and everything is good. Not so with the new card. I've even went into my regedits and uninstalled every bit of ati driver software before reinstalling my new card. Nothing's worked thus far. I've already exchanged my card out once and talked to customer support from my motherboard, microsoft, and ati all blaming the other. Please help me out!!

  Read the article

• Increasing Java's heapspace in Tomcat startup script

  - by Ankur

  I want to increase my heap size when using Tomcat. I was told to add this line export CATALINA_OPTS=-Xms16m -Xmx256m; In to the startup.sh script - I did so (at the beginning) but got the error export: 24: -Xmx256m: bad variable name Where am I supposed to add it, am I doing something else wrong? <b>export CATALINA_OPTS=-Xms16m -Xmx256m;</b> # Better OS/400 detection: see Bugzilla 31132 os400=false darwin=false case "`uname`" in CYGWIN*) cygwin=true;; OS400*) os400=true;; Darwin*) darwin=true;; esac # resolve links - $0 may be a softlink PRG="$0" while [ -h "$PRG" ] ; do ls=`ls -ld "$PRG"` link=`expr "$ls" : '.*-> \(.*\)$'` if expr "$link" : '/.*' > /dev/null; then PRG="$link" else PRG=`dirname "$PRG"`/"$link" fi done PRGDIR=`dirname "$PRG"` EXECUTABLE=catalina.sh # Check that target executable exists if $os400; then # -x will Only work on the os400 if the files are: # 1. owned by the user # 2. owned by the PRIMARY group of the user # this will not work if the user belongs in secondary groups eval else if [ ! -x "$PRGDIR"/"$EXECUTABLE" ]; then echo "Cannot find $PRGDIR/$EXECUTABLE" echo "This file is needed to run this program" exit 1 fi fi exec "$PRGDIR"/"$EXECUTABLE" start "$@"

  Read the article

• Word 2013 can't compare readonly files

  - by Moshe Katz

  I am using Tortoise SVN to work with a repository that contains some documentation saved as Word documents. On my old computer, with Office 2010, I was able to compare with previous revisions. Tortoise would open Word in compare view so I could see the differences between the files. I have installed Office 2013 (final version from Technet, not the preview version) on my new laptop for testing and now I can no longer compare Word Documents. Tortoise pops up a generic error that it was unable to compare the two files. Tortoise uses a JScript file to interface with Word, so I ran that file through a debugger and found that the actual error is: The Compare method or property is not available because this command is not available for reading. Some Googling followed by some testing revealed that the error is caused by the first file opened (in this case, the previous version) being opened as Read-Only. If I change the JScript code to open in normal mode, and I find the file on the system and un-check the "Read Only" property (if necessary), then the comparison opens as expected. I was unable to find any documentation about this change to Word on any Microsoft site. Does anyone know why this has been changed, and if it is intentional and not a bug, what the benefit is of requiring the file to be writable in order to compare it with another? Note: This is tagged word-2013-preview but it is actually for the release version of Word that is available on MSDN and Technet. I do not have enough rep. on this site to create new tags (yet).

  Read the article

• Cisco router not receiving OSPF updates

  - by WebDevHobo

  Or at least, that's what I think is happening. There doesn't appear to be a debug command for this, or to see if something is in the routing table. I'm testing out this setup in Packet Tracer. I have 3 routers and a webserver From left to right, you have: Webserver - Router1 - Router2 - Router3 Router1 and Router2 can succesfully ping WebServer. Router3 cannot. Router2 has a default gateway set, to send all not-recognized data through its serial interface to Router1. Like this: ip route 0.0.0.0 0.0.0.0 Serial 0/0/1 Serial 0/0/1 being the connection to Router1 Router2 and Router3 have OSPF configured. From their "show run": Router2: router ospf 1 log-adjacency-changes passive-interface Serial0/0/1 network 10.1.1.0 0.0.0.3 area 0 default-information originate ! Router3: router ospf 1 log-adjacency-changes network 10.1.1.0 0.0.0.3 area 0 passive-interface FastEthernet0/0 ! I was under the assumption that setting default-information originate on Router2 would give Router3 the needed information. What's going wrong here? The interfaces are up. Ip addresses are with mask-range, clock rate is set at correct end. I don't know what else to check.

  Read the article

• Windows errors, how do I find root cause and fix it? Getting several errors

  - by Eric Martin

  My server is having issues and not responding to customer's https requests. I checked the event viewer and found several errors. These two are listed a couple of times: WINS encountered a database error. This may or may not be a serious error. WINS will try to recover from it. You can check the database error events under 'Application Log' category of the Event Viewer for the Exchange Component, ESENT, source to find out more details about database errors. If you continue to see a large number of these errors consistently over time (a span of few hours), you may want to restore the WINS database from a backup. The error number is in the second DWORD of the data section. And this one: An error occured while using SSL configuration for socket address 0.0.0.0:444. The error status code is contained within the returned data. SQL Server is not ready to accept new client connections. Wait a few minutes before trying again. If you have access to the error log, look for the informational message that indicates that SQL Server is ready before trying to connect again. [CLIENT: xxx.xxx.xxxx.xxx] I also found this in the event viewer but the computer has been restarted since this message and I have not seen it again. Configuring the Page file for crash dump failed. Make sure there is a page file on the boot partition and that is large enough to contain all physical memory. This is my virtual memory settings: I'm not familiar with WINS so I wasn't sure if that is where I start or how to resolve it. Is the WINS error causing the other problems or should I be looking somewhere else?

  Read the article

• Where to get working Sysinternals tools for Windows 2000?

  - by mihi

  Yes, I know Windows 2000 will run end-of-life in this year, but we still have a lot of Windows 2000 boxes we try to migrate but no idea if all of them can be migrated this year... Recently I downloaded a new Sysinternals Suite (most recent file date 2010-03-25) and noticed that some tools just do not work on Windows 2000 any longer, which makes troubleshooting a lot harder. I checked all the tools in the suite to check which tools do not work, and dug through to find older versions that do work, but I don't know if there are more recent ones (with fewer bugs) available. I did not find any way to download old versions from Sysinternals website. :-( So here is my list: Does not work Works ADExplorer.exe 1.30.0.0 ? Coreinfo.exe 2.00 ? disk2vhd.exe 1.5.0.0 ? livekd.exe 3.14 3.0 procdump.exe 1.72 ? Procmon.exe 2.8 (Frequent crashes) Filemon/Regmon 7.04 ShellRunas.exe 1.01 ? vmmap.exe 2.62 2.2 ZoomIt.exe 4.1 1.21 If you know of any more recent versions (preferrably with download links) that work on Windows 2000, or an official download link for older versions, it would be highly appreciated.

  Read the article

• Tomcat won't shutdown gracefully -how can I tell if the shutdown port is open?

  - by gav

  Hi, I installed Tomcat 6 using the tar-ball via wget. Startup of the server is fine but on shutdown I get a timeout exception. root@88:/usr/local/tomcat/logs# /usr/local/tomcat/bin/shutdown.sh Using CATALINA_BASE: /usr/local/tomcat Using CATALINA_HOME: /usr/local/tomcat Using CATALINA_TMPDIR: /usr/local/tomcat/temp Using JRE_HOME: /usr Using CLASSPATH: /usr/local/tomcat/bin/bootstrap.jar 30-Mar-2010 17:33:41 org.apache.catalina.startup.Catalina stopServer SEVERE: Catalina.stop: java.net.ConnectException: Connection timed out at java.net.PlainSocketImpl.socketConnect(Native Method) at java.net.PlainSocketImpl.doConnect(PlainSocketImpl.java:333) at java.net.PlainSocketImpl.connectToAddress(PlainSocketImpl.java:195) at java.net.PlainSocketImpl.connect(PlainSocketImpl.java:182) at java.net.SocksSocketImpl.connect(SocksSocketImpl.java:366) ... I read that this might be because I have a firewall blocking incoming connections on the shutdown port (8005). I have a default Ubuntu 9.04 installation running on a VPS with no rules in my iptables. How can I tell if that port is blocked? How can I check that the server is listening for connections on 8005? Bizarrely pinging localhost or the IP of my server fails from the server itself, whereas pinging the IP of my server from another machine succeeds. Gav

  Read the article

• Amazon VPC NAT not working

  - by rpkelly

  I'm trying to create a NAT instance for my VPC to allow instances on private subnets connect to the internet (most importantly, S3). I tried following the instructions here: http://docs.amazonwebservices.com/AmazonVPC/2011-07-15/UserGuide/index.html?VPC_NAT_Instance.html . Unfortunately, the instances in the private subnet (call it 10.10.2.0/24) cannot reach the internet. I have done the following: Create a NAT instance (Amazon's ami-vpc-nat-1.0.0-beta.i386-ebs (ami-d8699bb1)) in public subnet (call it 10.10.1.0/24). Changed "Source / Dest Check" to disabled. Created a new entry in the default routing table (which is used by 10.10.2.0/24) and had it point to the ID of the newly created instance. Associated an Elastic IP address with the NAT instance. Allowed all outbound traffic on the security group of the NAT instance. Ensured that all traffic could pass between the two subnets. I've tried also doing this with an existing instance using iptables, but had no luck. And I have verified that sys.net.ipv4.ip_forward is 1, just in case anyone was wondering. And I still have no internet connectivity from the instances on 10.10.2.0/24. Does anyone have any suggestions?

  Read the article

• Can a hardware firewall block a server accessing its OWN UNC shares?

  - by Simon

  I need to set up a UNC share for my hosted dedicated server to access a share on itself. Unfortunately TFS requires a UNC share. I am on a Windows Server 2008 Standard SP2 64bit dedicated server behind a PIX 501 firewall hosted with GoDaddy. I just cannot get the server to access itself and get this error: Windows cannot access \\SERVER\SHARE Check the spelling of the name.. etc. I've found numerous questions about this but no answer to my problem. Server 2008 Standard x64 SP2 Workgroup - not domain Windows Firewall is off Computer browser service is on I am trying to access \\MYMACHINE\TFS-BUILDS by typing in - or double clicking. Neither works. Machine has single network card Filesharing wizard says share was ok Share was showing under 'Computer management' Permissions are set to 'everyone' full control No obvious errors in eventlog Reboot didn't fix it Unfortunately I cannot try to access other shares in or out of this machine because it is a hosted dedicated server and the only machine behind a hardware firewall. The only thing left i can think of is that the hardware firewall needs to be configured. Is this possible? Does 'UNC traffic' go out of the machine and then back in again?

  Read the article

• What should I be doing while I wait for a progress bar?

  - by Malnizzle

  So I am sitting here waiting for a progress bar to run (20 mins or so), and was wondering how best to use my time as a SysAdmin. I debated not posting this question briefly, as this could get flagged as subjective, but I think it's an important question, and a question that can be legitimately answered (per the FAQ) I know this something a lot of sys admins deal with, especially if they are client-based I would venture to guess. There is a lot of material out there about how to multi task, but SysAdmin work is unique in this area as well. I could switch over to another project, but I could get wrapped up in that, and forget about the original project I was working on, and that's hard if you are billing a client for your time, both for tracking your time, as well as being fair to that client. I could check ServerFault, but that isn't directly work related, I could sort my email, so on and so forth. What do you do, or what should I do when I have time waiting for a progress bar? Thanks! (download done, back to work!)

  Read the article

• Installing Silverstripe on 000webhost.com (free web host)

  - by benwad

  Hi I'm trying to learn how to work Silverstripe so I extracted the tar file to my free hosting account. I then went on install.php and edited the permissions to meet the requirements set out in install.php but I still get two warnings from the 'webserver configuration' section: I can't tell what webserver you are running. Without Apache I can't tell if mod_rewrite is enabled. I can't tell whether mod_rewrite is running. You may need to configure a rewriting rule yourself. I looked in phpinfo() and mod_rewrite appears to be installed. I contacted the web host and they said it was to do with virtual directory paths, and I should add 'RewriteBase /' to the top of my .htaccess file in the public_html directory. However I did this and still had the same problem. The install.php script says that I can install it even with these warnings but when I press 'install' it just refreshes the install.php page. It doesn't even overwrite the .htaccess file. 000webhost.com says they have successfully installed Silverstripe on their user accounts without much configuration but I can't seem to find out how. EDIT: I managed to get to the next page but now there is another warning which is stopping it installing: Friendly URLs are not working. This is most likely because mod_rewrite isn't configuredcorrectly on your site. Please check the following things in your Apache configuration; you may need to get your web host or server administrator to do this for you: * mod_rewrite is enabled * AllowOverride All is set for your directory I also get this error message from the server: Warning: unlink(mysite/_config.php) [function.unlink]: Permission denied in /home/a2716553/public_html/install.php on line 701

  Read the article

• How to enable error log in lighttpd properly?

  - by Tomaszs

  I have a Centos 5 system with Lighttpd and fastcgi enabled. It does log access but does not log errors. I have Internal Server Error 500 and no info in log and when I try to open not -existing file also - no info in error log. How to enable it properly? Below is list of modules that I've enabled: server.modules = ( "mod_rewrite", "mod_redirect", "mod_alias", # "mod_access", # "mod_cml", # "mod_trigger_b4_dl", # "mod_auth", "mod_status", "mod_setenv", "mod_fastcgi", # "mod_webdav", # "mod_proxy_core", # "mod_proxy_backend_fastcgi", # "mod_proxy_backend_scgi", # "mod_proxy_backend_ajp13", # "mod_simple_vhost", # "mod_evhost", # "mod_userdir", # "mod_cgi", # "mod_compress", # "mod_ssi", # "mod_usertrack", # "mod_expire", # "mod_secdownload", # "mod_rrdtool", "mod_accesslog" ) Here are setting of debugging: ## enable debugging #debug.log-request-header = "enable" #debug.log-response-header = "enable" #debug.log-request-handling = "enable" debug.log-file-not-found = "enable" #debug.log-condition-handling = "enable" Setting of path to error and access log: ## where to send error-messages to server.errorlog = "/home/lxadmin/httpd/lighttpd/error.log" #### accesslog module accesslog.filename = "/home/lxadmin/httpd/lighttpd/ligh.log" Settings of fastcgi: fastcgi.debug = 1 fastcgi.server = ( ".php" => (( "bin-path" => "/usr/bin/php-cgi", "socket" => "/tmp/php.socket", "max-procs" => 12, "bin-environment" => ( "PHP_FCGI_CHILDREN" => "2", "PHP_FCGI_MAX_REQUESTS" => "500" ) ))) And in included config file I have: server.errorlog = "/home/httpd/mywebsite.com/stats/mywebsite.com-error_log" What comes to log files: /home/httpd/mywebsite.com/stats/ -rw-r--r-- 1 apache apache 5173239 May 16 11:34 mywebsite.com-custom_log -rwxrwxrwx 1 root root 0 Mar 27 2009 mywebsite.com-error_log /home/lxadmin/httpd/lighttpd/ -rwxrwxrwx 1 apache apache 2184 Apr 22 22:59 error.log -rwxrwxrwx 1 apache apache 6088621 May 16 11:26 ligh.log I gave error logs chmod 777 for a try to check if it's the issue, but apparently it's not. So my question is: what to do to have error log enabled?

  Read the article

• How to restrict postfix send limited email with policyd v2?

  - by Shalini Tripathi

  I have installed cluebringer-2.0.7 for postfix and enabled below lines in the main.cf file of postfix. But I could not see any policy working smtpd_recipient_restrictions = permit_mynetworks permit_sasl_authenticated reject_unauth_destination check_policy_service inet:127.0.0.1:10031 smtpd_end_of_data_restrictions=check_policy_service inet:127.0.0.1:10031 To check further I enabled logging in policyd and its only shows below logs and there is no logs getting populated when I send new emails.. [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: Process Backgrounded [2012/06/12-21:18:50 - 13949] [CBPOLICYD] NOTICE: Policyd v2 / Cluebringer - v2.0.7 [2012/06/12-21:18:50 - 13949] [CBPOLICYD] NOTICE: Initializing system modules. [2012/06/12-21:18:50 - 13949] [CBPOLICYD] NOTICE: System modules initialized. [2012/06/12-21:18:50 - 13949] [CBPOLICYD] NOTICE: Module load started... [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: = AccessControl: enabled [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: = CheckHelo: enabled [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: = CheckSPF: enabled [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: = Greylisting: enabled [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: = Quotas: enabled [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: = Protocol(Postfix): enabled [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: = Protocol(Bizanga): enabled [2012/06/12-21:18:50 - 13949] [CBPOLICYD] NOTICE: Module load done. [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: 2012/06/12-21:18:50 cbp (type Net::Server::PreFork) starting! pid(13949) [2012/06/12-21:18:50 - 13949] [CORE] NOTICE: Binding to TCP port 10031 on host * [2012/06/12-21:18:50 - 13949] [CORE] WARNING: Group Not Defined. Defaulting to EGID '0 10 6 4 3 2 1 0' [2012/06/12-21:18:50 - 13949] [CORE] WARNING: User Not Defined. Defaulting to EUID '0' Do I need to do anymore settings for postfix to listen on policyd???Please help

  Read the article

• Monitoring outgoing messages using EXIM

  - by dashmug

  I work as an IT guy in a law firm. I am recently asked to make a system wherein all the outgoing emails coming from our server to our clients will be put on hold first and wait for approval before it gets sent to the client. Our mail server uses Exim (that's what it says in cPanel). I am planning to create filters where the outgoing emails will be forwarded to an editor account. Then, the editor will review and edit the contents of the email. When the editor already approves the email, it will then get sent to the client by the editor but still using the original sender in the "From:" and "Reply-To:" field. I found some pointers from this site = http://www.devco.net/archives/2006/03/24/saving_copies_of_all_email_using_exim.php. Once the filters are in place, I want to make a simple PHP interface for the editor to check the forwarded emails and edit them if necessary. The editor can then click on an "Approve" button that will finally deliver the message using the original sender. I'm also thinking that maybe a PHP-less system will be enough. The editor can receive the emails from his own email client edit them and simply send the email as if he is the original sender. Is my plan feasible? Will there be issues that I have overlooked? Does it have the danger of being treated as spam by the other mailservers since I'll be messing up the headers?

  Read the article

< Previous Page | 618 619 620 621 622 623 624 625 626 627 628 629  | Next Page >