Search Results

Search found 16903 results on 677 pages for 'single responsibility'.

Page 635/677 | < Previous Page | 631 632 633 634 635 636 637 638 639 640 641 642  | Next Page >

• XFS disk becomes unavailable after a while

  - by Guard

  Ubuntu 12.04 (but the same was on 11.10 before upgrading) WD MyBook, 2TB, no RAID (or RAID0, not completely sure, anyway no mirroring, both 1TB disks are in use, mounted as a single device). Formatted to XFS, normally used for big movie files. Connected to Firewire 800. At some point the LED started going up and down as when constantly reading/writing. The device gives access error. When unplugged (cable, then holding the power button for a while, then unplugging the power) and re-connected becomes available. xfs_check with no results. xfs_repair did something, but looks like didn't fix any error. Then after a massive read (checking 1.5GB torrent file for integrity) becomes unavailable again. Any ideas what's wrong? Drives? Cables? Motherboard? OS? UPD: not sure how relevant this is, but here are dmesg output [14380.632816] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled [14380.633356] SGI XFS Quota Management subsystem [14421.812220] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 [14441.890596] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 [14441.896858] firewire_core: phy config: card 0, new root=ffc1, gap_count=5 [14453.895347] firewire_core: created device fw1: GUID 0090a99500a35518, S400, 9 config ROM retries [14453.904818] scsi6 : SBP-2 IEEE-1394 [14453.905014] scsi7 : SBP-2 IEEE-1394 [14454.139993] firewire_sbp2: fw1.0: logged in to LUN 0000 (0 retries) [14454.158769] scsi 6:0:0:0: Direct-Access WD My Book 1015 PQ: 0 ANSI: 4 [14454.159251] sd 6:0:0:0: Attached scsi generic sg3 type 0 [14454.162391] firewire_sbp2: fw1.1: logged in to LUN 0001 (0 retries) [14454.167453] sd 6:0:0:0: [sdc] 3907017568 512-byte logical blocks: (2.00 TB/1.81 TiB) [14454.178822] sd 6:0:0:0: [sdc] Write Protect is off [14454.178826] sd 6:0:0:0: [sdc] Mode Sense: 10 00 00 00 [14454.186830] scsi 7:0:0:1: Enclosure WD My Book Device 1015 PQ: 0 ANSI: 4 [14454.186995] scsi 7:0:0:1: Attached scsi generic sg4 type 13 [14454.190078] sd 6:0:0:0: [sdc] Cache data unavailable [14454.190087] sd 6:0:0:0: [sdc] Assuming drive cache: write through [14454.202176] sd 6:0:0:0: [sdc] Cache data unavailable [14454.202185] sd 6:0:0:0: [sdc] Assuming drive cache: write through [14454.239940] sdc: [mac] sdc1 sdc2 sdc3 sdc4 [14454.271262] sd 6:0:0:0: [sdc] Cache data unavailable [14454.271270] sd 6:0:0:0: [sdc] Assuming drive cache: write through [14454.271354] sd 6:0:0:0: [sdc] Attached SCSI disk [14454.272149] ses 7:0:0:1: Attached Enclosure device [14606.090024] XFS (sdc3): Mounting Filesystem [14612.048343] XFS (sdc3): Starting recovery (logdev: internal) [14620.697636] XFS (sdc3): Ending recovery (logdev: internal) [14748.120957] e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: Rx/Tx [14748.120963] e1000e 0000:00:19.0: eth0: 10/100 speed: disabling TSO [14752.568382] uhci_hcd 0000:00:1a.0: PCI INT A disabled [14752.568579] uhci_hcd 0000:00:1a.1: PCI INT B disabled [14752.568738] ehci_hcd 0000:00:1a.7: PCI INT C disabled [14752.568779] ehci_hcd 0000:00:1a.7: PME# enabled [14752.584526] uhci_hcd 0000:00:1d.1: PCI INT B disabled [14752.584689] uhci_hcd 0000:00:1d.2: PCI INT C disabled [14752.680079] ehci_hcd 0000:00:1a.7: BAR 0: set to [mem 0xe4641000-0xe46413ff] (PCI address [0xe4641000-0xe46413ff]) [14752.680104] ehci_hcd 0000:00:1a.7: restoring config space at offset 0xf (was 0x300, writing 0x30b) [14752.680136] ehci_hcd 0000:00:1a.7: restoring config space at offset 0x1 (was 0x2900000, writing 0x2900002) [14752.680170] ehci_hcd 0000:00:1a.7: PME# disabled [14752.680182] ehci_hcd 0000:00:1a.7: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [14752.680190] ehci_hcd 0000:00:1a.7: setting latency timer to 64 [14752.710334] uhci_hcd 0000:00:1a.0: PCI INT A -> GSI 16 (level, low) -> IRQ 16 [14752.710342] uhci_hcd 0000:00:1a.0: setting latency timer to 64 [14752.749186] uhci_hcd 0000:00:1a.1: PCI INT B -> GSI 17 (level, low) -> IRQ 17 [14752.749194] uhci_hcd 0000:00:1a.1: setting latency timer to 64 [14752.790231] uhci_hcd 0000:00:1d.1: PCI INT B -> GSI 22 (level, low) -> IRQ 22 [14752.790239] uhci_hcd 0000:00:1d.1: setting latency timer to 64 [14752.829170] uhci_hcd 0000:00:1d.2: PCI INT C -> GSI 18 (level, low) -> IRQ 18 [14752.829178] uhci_hcd 0000:00:1d.2: setting latency timer to 64

  Read the article

• APACHE2.2/WIN2003(32-bit)/PHP: How do I configure Apache to Run Background PHP Processes on Win 2003

  - by Captain Obvious

  I have a script, testforeground.php, that kicks off a background script, testbackground.php, then returns while the background script continues to run until it's finished. Both the foreground and background scripts write to the output file correctly when I run the foreground script from the command line using php-cgi: C:\>php-cgi testforeground.php The above command starts a php-cgi.exe process, then a php-win.exe process, then closes the php-cgi.exe almost immediately, while the php-win.exe continues until it's finished. The same script runs correctly but does not have permission to write to the output file when I run it from the command line using plain php: C:\>php testforeground.php AND when I run the same script from the browser, instead of php-cgi.exe, a single cmd.exe process opens and closes almost instantly, only the foreground script writes to the output file, and it doesn't appear that the 2nd process starts: http://XXX/testforeground.php Here is the server info: OS: Win 2003 32-bit HTTP: Apache 2.2.11 PHP: 5.2.13 Loaded Modules: core mod_win32 mpm_winnt http_core mod_so mod_actions mod_alias mod_asis mod_auth_basic mod_authn_default mod_authn_file mod_authz_default mod_authz_groupfile mod_authz_host mod_authz_user mod_autoindex mod_cgi mod_dir mod_env mod_include mod_isapi mod_log_config mod_mime mod_negotiation mod_setenvif mod_userdir mod_php5 Here's the foreground script: <?php ini_set("display_errors",1); error_reporting(E_ALL); echo "<pre>loading page</pre>"; function run_background_process() { file_put_contents("0testprocesses.txt","foreground start time = " . time() . "\n"); echo "<pre> foreground start time = " . time() . "</pre>"; $command = "start /B \"{$_SERVER['CMS_PHP_HOMEPATH']}\php-cgi.exe\" {$_SERVER['CMS_HOMEPATH']}/testbackground.php"; $rp = popen($command, 'r'); if(isset($rp)) { pclose($rp); } echo "<pre> foreground end time = " . time() . "</pre>"; file_put_contents("0testprocesses.txt","foreground end time = " . time() . "\n", FILE_APPEND); return true; } echo "<pre>calling run_background_process</pre>"; $output = run_background_process(); echo "<pre>output = $output</pre>"; echo "<pre>end of page</pre>"; ?> And the background script: <?php $start = "background start time = " . time() . "\n"; file_put_contents("0testprocesses.txt",$start, FILE_APPEND); sleep(10); $end = "background end time = " . time() . "\n"; file_put_contents("0testprocesses.txt", $end, FILE_APPEND); ?> I've confirmed that the above scripts work correctly using Apache 2.2.3 on Linux. I'm sure I just need to change some Apache and/or PHP config settings, but I'm not sure which ones. I've been muddling over this for too long already, so any help would be appreciated.

  Read the article

• Choice of an OS for a home ZFS NAS

  - by OlafM

  I am preparing a home NAS with an old Athlon 64 X2 3800+, 4 GB ECC RAM, Asus M2V MX motherboard, and a single 3 TB WDC Green (another one as mirror may be installed in the future). It's the cheapest solution I found that includes ECC memory and the higher energy consumption is offset by the lower (zero) cost of acquisition. The system will be used for: music storage and stream to other desktop computers; storage of the scanned dia slides (3-4k slides, 180 MB TIFF each one plus reduced quality JPEG version); stream of these photos to a local iPad 2 (maybe Plex App? not yet sure); (one additional) remote backup via rsync/ssh or ZFS send/receive. It will be controlled via remote ssh, maybe VNC, no monitor attached. Absolute requirement is a reliable ZFS solution, plus the ability to easily install packets/software/virtual machines and to update remotely (I will be the admin and I don't live near the NAS). I have mainly three options: NAS4free/FreeNAS OpenIndiana Solaris Express 11 (yeah yeah I know the license requirements, I will write a perl script on it to count it as development machine). Problems: NAS4free/FreeNAS (I tested only NAS4free) required embedded installation for remote upgrading, but full install for easy addition of software packets. Since I need at least AirVideo Server (linux/win) and Plex App (win/linux) to stream the photos and some videos to iPad (they both require virtualbox), but I cannot be there to install updates, NAS4free/FreeNAS are excluded. http://www.nas4free.org/general_information.html explains the issue: embedded can be remotely updated, full cannot. Solaris has also another advantage: Crashplan client supports Solaris and I'm already using it for other backups. I would like to leave the option open, even if I will be doing backups probably through zfs send/receive. NexentaStor was left out because zfs send/receive are not included in the free version. The question is now Solaris 11 Express over OpenIndiana. To ease the management, I will be using http://www.napp-it.org Which one would you suggest and why? I found lots of informations and it's difficult for me to decide. I think (from the napp-it manual) that Solaris has some additional options for SMB shares, but are they really needed at home? I think I won't even use ACLs, since normal unix-style permissions are enough. OpenIndiana has maybe more frequent updates (Solaris offers only security updates between releases), but again, do I need them? I don't think so. Moreover, this is a NAS that has to work and nothing else, I cannot risk having problems that require me to access the server. Isn't OpenIndiana a bit more... cutting edge (in the Solaris world)? I'm just asking, no need to focus on this for the answer :-) I would limit myself to these two options (SE11.1/OI) also because I will be making a NAS for me in the future (where high performances with Mac shares are also required) and Solaris has kernel support for AFP. I will use this server to gather experience as well. After this long question, thanks in advance! If you need additional info, let me know and I will update this post.

  Read the article

• Intermittent lockups, unable to diagnose in over a year

  - by Magsol

  Here's a real doosie; I may just give my firstborn child to whomever helps me solve this problem. In July 2008, I assembled what would be my desktop computer for graduate school. Here are the specs of the machine I built: Thermaltake 750W PSU Corsair Dominator 2x2GB 240-pin SDRAM Thermaltake Tower Asus P5K Deluxe Motherboard Intel Core 2 Quad Q9300 2.5GHz CPU 2 x GeForce 8600 GT WD Caviar Blue 640GB hard drive CD burner DVD burner Soon thereafter, I ordered a new motherboard (because I was an idiot; that first motherboard supported CrossFire, not SLI), an Asus P5N-D. I was originally running Windows XP SP3. Pretty much right into the start of the fall semester, my desktop would simply lock up after awhile. If my system was largely idling, it would be after 1-3 days. If was gaming, it often happened an hour or two into my gaming session, indicating a link to activity level. Here's where it started getting interesting. I started looking at the system temps. The CPU was warmer than it should have been (~60s C), so I purchased some more efficient cooling compound a way better cooler for it. Now it hardly goes over 40 C. Intel was even kind enough to swap it out for free, just to rule it out. Lockups continued. The graphics cards were also running pretty warm: about 60 C idling. Removing one of them seemed to improve stability a little bit...as in, it wouldn't lock up quite as frequently, but still always eventually locked up. But it didn't matter which card I used or removed, the lockups continued. I reverted back to the original motherboard, the P5K Deluxe. Lockups continued. I purchased an entirely new motherboard, eVGA's nForce 750i. Lockups continued. Ran memtest86+ over and over and over, with no errors. Even RMA'd the memory. Lockups continued. Replaced the PSU with a Corsair 750W PSU. Lockups continued. Tried disconnecting all IDE drives (HDDs are SATA). Lockups continued. Replaced both graphics cards with a single Radeon HD 4980. Average temps are now always around 50 C when idling, 60 C only when gaming. Lockups continued. Throughout the whole ordeal, the system has been upgraded from Windows XP SP3 to Vista 32-bit, to Vista 64-bit, and is now at Windows 7 64-bit. Lockups have occurred at every step along the way (each OS was in place for at least a few months before the next upgrade). Edit: By "upgrade" I mean clean install each time. In addition to those reformats, I have performed many, many other reformats of the system and a reinstall of whatever OS had been previously installed in an attempt to rectify this problem, to no avail./Edit When the system locks up, there's no blue screen, no reboot, no error message of any kind. It simply freezes in place until I hit the reset button. Very, very rarely, once Windows boots back up, the system informs me that Windows has recovered from an error, but it can never find the source aside from some piece of hardware. I've swapped out every component in this computer, and there are more fans in it than I care to count...though for the sake of completeness: top 80mm case fan (out) rear 80mm case fan (out) rear 120mm case fan (out) front 120mm case fan (in) side 250mm case fan (in) giant CPU fan on-board motherboard fan (the eVGA board) triple-fan memory setup (came with the memory) PSU internal fan another 120mm fan I stuck on the underside of the video card to keep hot air from collecting at the bottom of the case I'm truly out of ideas. ANY help at all would be oh-so-very GREATLY appreciated. Thank you!

  Read the article

• Cheapest way to connect 20-24 Sata II HDDs in a budget storage server?

  - by Joe Hopfgartner

  I need to assemble a high density storage server for as cheap as possible. It's been a while for me and the last systems I integrated didn't even have Sata yet... During my Research I of course stumbled about Nexsan SATA Beast, the BackBlaze storage Pods as well as some ridiculously overpriced HP Proliant or Dell storage solutions. Finally I choose Norco cases as the way to go. My eye is set on the RPC-4020, which is a 4U 19" Rackmount case with 20 Hot Swap 3.5" SATA/SAS Hdd trays (Backplanes included) and room for two 2.5" OS drives as well as a Slim Line CD-Rom. The backplanes connect with a single SATA port for each drive, so there are 20 internal SATA ports to to be connected. They also have redundant power ports which I think is quite nice. The cheapest price I have found is 290$ + 40$ shipping. In europe the cheapest unfortunately is 370€ (500$) + 40 € shipping... A nice alternative would be the RPC-4224 which has SFF-8087 Mini SAS connectors that bundle 4 SATA trays each. But it doesn't seem to be available in Europe (where i am) anywhere. So here comes my problem: What Mainboard/Controller to choose to connect them for as cheap as possible while still having nice data rates? I have to say that the server is intended as a Storage server with 1gps connectivity and the data transfer will be distributed very evenly across all drives. I also don't require any raid functionality. This is all done at application level, I just need JBOD. So for example if I go for the RPC 4020 Model I need to connect 20 Storage + 1 OS + 1 CDROM Sata ports. I searched a bit and stumbled across this very low priced controller: http://www.intel.com/products/server/raid-controllers/SASWT4I/SASWT4I-overview.htm They sell it for 115 € here and the specs say it can control up to 122 hard discs and has 4 Mini SAS connectors. So I would use 4 Mini SAS 36pin - 4 SATA 7pin cables to connect 4 SATA drives to each port and choose a Mainboard taht has 6 SATA on board (for example this one) and hurray, I can connect my 22 SATA devices for as low as about ~ 220 EUR (cpu, ram, psu, case not counted) Question: WOULD THAT WORK? And if not, why? 2nd Question: If I go for the 4220 or 4224 Model, I have internal Mini SAS connectors. Am I right in assuming that the backplane than acts as a "SAS Expander"? And can I just plug these SAS connectors into any SAS port I can find on my controller / mainboard or are there certain requirements? I know that SATA port multipliers only work with controllers that are ready for that. But isn't this expansion already implemented in the SAS standard? I am sorry that this is a very broad question, but I really spent the last week reading up and it seems to be not so clear! Especially all the controlling hardware specifications! 3rd Question: A lot of hardware specs feature "internal channels" and "internal connectors". The connecors are the physical numbers of places where I can plug a cable in. I got that. But are the "internal channels" always the maximum numbers of physical drives that can be used in the end? Or can I enhance this further by Expanders/Fanouts? 4th and last question: What do you think about the setup so far? Do you know any good alternatives? Maby I am completely going the wrong way and some DAS would be way better? Are there any comparable chassis available in europe? Please feel free to say whatever you think is relevant to the subject!

  Read the article

• FFMPEG dropping frames while encoding JPEG sequence at color change

  - by Matt

  I'm trying to put together a slide show using imagemagick and FFMPEG. I use imagemagick to expand a single photo into 30fps video (imagemagick also handles things like putting some text captions on the frames along the way). When I go to let ffmpeg digest it into a video it clips along nicely on the color parts of the video, but when it gets to a black and white section it reports "frame= 2030 fps=102 q=32766.0 Lsize= 5203kB time=00:01:07.60 bitrate= 630.5kbits/s dup=0 drop=703" and drops every frame of video until it hits something with color. As you can imagine this results in entire photos being removed from the slideshow. Here is my latest dump... ffmpeg -y -r 30 -i "teststream/%06d.jpg" -c:v libx264 -r 30 newffmpeg.mp4 ffmpeg version git-2012-12-10-c3bb333 Copyright (c) 2000-2012 the FFmpeg developers built on Dec 10 2012 22:02:04 with gcc 4.6.1 (Ubuntu/Linaro 4.6.1-9ubuntu3) configuration: --enable-gpl --enable-libfaac --enable-libmp3lame --enable-libopencore-amrnb --enable-libopencore-amrwb --enable-librtmp --enable-libtheora --enable-libvorbis --enable-libx264 --enable-nonfree --enable-version3 libavutil 52. 12.100 / 52. 12.100 libavcodec 54. 79.101 / 54. 79.101 libavformat 54. 49.100 / 54. 49.100 libavdevice 54. 3.102 / 54. 3.102 libavfilter 3. 26.101 / 3. 26.101 libswscale 2. 1.103 / 2. 1.103 libswresample 0. 17.102 / 0. 17.102 libpostproc 52. 2.100 / 52. 2.100 Input #0, image2, from 'teststream/%06d.jpg': Duration: 00:12:02.80, start: 0.000000, bitrate: N/A Stream #0:0: Video: mjpeg, yuvj444p, 720x480 [SAR 72:72 DAR 3:2], 25 fps, 25 tbr, 25 tbn, 25 tbc [libx264 @ 0x3450140] using SAR=1/1 [libx264 @ 0x3450140] using cpu capabilities: MMX2 SSE2Fast SSSE3 FastShuffle SSE4.2 [libx264 @ 0x3450140] profile High, level 3.0 [libx264 @ 0x3450140] 264 - core 129 r2 1cffe9f - H.264/MPEG-4 AVC codec - Copyleft 2003-2012 - http://www.videolan.org/x264.html - options: cabac=1 ref=3 deblock=1:0:0 analyse=0x3:0x113 me=hex subme=7 psy=1 psy_rd=1.00:0.00 mixed_ref=1 me_range=16 chroma_me=1 trellis=1 8x8dct=1 cqm=0 deadzone=21,11 fast_pskip=1 chroma_qp_offset=-2 threads=12 lookahead_threads=2 sliced_threads=0 nr=0 decimate=1 interlaced=0 bluray_compat=0 constrained_intra=0 bframes=3 b_pyramid=2 b_adapt=1 b_bias=0 direct=1 weightb=1 open_gop=0 weightp=2 keyint=250 keyint_min=25 scenecut=40 intra_refresh=0 rc_lookahead=40 rc=crf mbtree=1 crf=23.0 qcomp=0.60 qpmin=0 qpmax=69 qpstep=4 ip_ratio=1.40 aq=1:1.00 Output #0, mp4, to 'newffmpeg.mp4': Metadata: encoder : Lavf54.49.100 Stream #0:0: Video: h264 ([33][0][0][0] / 0x0021), yuvj420p, 720x480 [SAR 1:1 DAR 3:2], q=-1--1, 15360 tbn, 30 tbc Stream mapping: Stream #0:0 - #0:0 (mjpeg - libx264) Press [q] to stop, [?] for help Input stream #0:0 frame changed from size:720x480 fmt:yuvj444p to size:720x480 fmt:yuvj422p Input stream #0:0 frame changed from size:720x480 fmt:yuvj422p to size:720x480 fmt:yuvj444pp=584 frame= 2030 fps=102 q=32766.0 Lsize= 5203kB time=00:01:07.60 bitrate= 630.5kbits/s dup=0 drop=703 video:5179kB audio:0kB subtitle:0 global headers:0kB muxing overhead 0.472425% [libx264 @ 0x3450140] frame I:9 Avg QP:20.10 size: 33933 [libx264 @ 0x3450140] frame P:636 Avg QP:24.12 size: 6737 [libx264 @ 0x3450140] frame B:1385 Avg QP:27.04 size: 514 [libx264 @ 0x3450140] consecutive B-frames: 2.5% 15.2% 13.2% 69.2% [libx264 @ 0x3450140] mb I I16..4: 8.3% 80.3% 11.5% [libx264 @ 0x3450140] mb P I16..4: 1.5% 2.5% 0.2% P16..4: 41.7% 18.0% 10.3% 0.0% 0.0% skip:25.9% [libx264 @ 0x3450140] mb B I16..4: 0.0% 0.0% 0.0% B16..8: 26.6% 0.6% 0.1% direct: 0.2% skip:72.3% L0:35.0% L1:60.3% BI: 4.7% [libx264 @ 0x3450140] 8x8 transform intra:64.1% inter:75.1% [libx264 @ 0x3450140] coded y,uvDC,uvAC intra: 51.6% 78.0% 43.7% inter: 10.6% 14.9% 2.1% [libx264 @ 0x3450140] i16 v,h,dc,p: 29% 19% 6% 46% [libx264 @ 0x3450140] i8 v,h,dc,ddl,ddr,vr,hd,vl,hu: 23% 15% 17% 5% 9% 10% 7% 8% 6% [libx264 @ 0x3450140] i4 v,h,dc,ddl,ddr,vr,hd,vl,hu: 31% 18% 11% 5% 9% 10% 6% 6% 4% [libx264 @ 0x3450140] i8c dc,h,v,p: 46% 18% 24% 12% [libx264 @ 0x3450140] Weighted P-Frames: Y:20.1% UV:18.7% [libx264 @ 0x3450140] ref P L0: 59.2% 23.2% 13.1% 4.3% 0.2% [libx264 @ 0x3450140] ref B L0: 88.7% 8.3% 3.0% [libx264 @ 0x3450140] ref B L1: 95.0% 5.0% [libx264 @ 0x3450140] kb/s:626.88 Received signal 2: terminating. One last note: If I remove the -r 30 from the input and output it works flawlessly. I have no idea why the -r 30 is causing it to freak out.

  Read the article

• How do I configure Apache 2.2 to Run Background PHP Processes on Win 2003?

  - by Captain Obvious

  I have a script, testforeground.php, that kicks off a background script, testbackground.php, then returns while the background script continues to run until it's finished. Both the foreground and background scripts write to the output file correctly when I run the foreground script from the command line using php-cgi: C:\>php-cgi testforeground.php The above command starts a php-cgi.exe process, then a php-win.exe process, then closes the php-cgi.exe almost immediately, while the php-win.exe continues until it's finished. The same script runs correctly but does not have permission to write to the output file when I run it from the command line using plain php: C:\>php testforeground.php AND when I run the same script from the browser, instead of php-cgi.exe, a single cmd.exe process opens and closes almost instantly, only the foreground script writes to the output file, and it doesn't appear that the 2nd process starts: http://XXX/testforeground.php Here is the server info: OS: Win 2003 32-bit HTTP: Apache 2.2.11 PHP: 5.2.13 Loaded Modules: core mod_win32 mpm_winnt http_core mod_so mod_actions mod_alias mod_asis mod_auth_basic mod_authn_default mod_authn_file mod_authz_default mod_authz_groupfile mod_authz_host mod_authz_user mod_autoindex mod_cgi mod_dir mod_env mod_include mod_isapi mod_log_config mod_mime mod_negotiation mod_setenvif mod_userdir mod_php5 Here's the foreground script: <?php ini_set("display_errors",1); error_reporting(E_ALL); echo "<pre>loading page</pre>"; function run_background_process() { file_put_contents("0testprocesses.txt","foreground start time = " . time() . "\n"); echo "<pre> foreground start time = " . time() . "</pre>"; $command = "start /B \"{$_SERVER['CMS_PHP_HOMEPATH']}\php-cgi.exe\" {$_SERVER['CMS_HOMEPATH']}/testbackground.php"; $rp = popen($command, 'r'); if(isset($rp)) { pclose($rp); } echo "<pre> foreground end time = " . time() . "</pre>"; file_put_contents("0testprocesses.txt","foreground end time = " . time() . "\n", FILE_APPEND); return true; } echo "<pre>calling run_background_process</pre>"; $output = run_background_process(); echo "<pre>output = $output</pre>"; echo "<pre>end of page</pre>"; ?> And the background script: <?php $start = "background start time = " . time() . "\n"; file_put_contents("0testprocesses.txt",$start, FILE_APPEND); sleep(10); $end = "background end time = " . time() . "\n"; file_put_contents("0testprocesses.txt", $end, FILE_APPEND); ?> I've confirmed that the above scripts work correctly using Apache 2.2.3 on Linux. I'm sure I just need to change some Apache and/or PHP config settings, but I'm not sure which ones. I've been muddling over this for too long already, so any help would be appreciated.

  Read the article

• Thoughts on home NAS server

  - by user826955

  I currently have a NAS with a 2x2TB HDD 1x16GB SSD layout on a mini-itx atom board. The NAS is in a Lian Li PC-Q07 case. On this system I was running freebsd 8 with a gmirror raid 1 setup, which was enough for my needs. So far I was using the NAS for: Fileserver with AFP protocol (only mac clients used) SVN server hosting all my source trees of my projects JIRA (performance was okay-ish) Timemachine backup for the macs The power consumption was about 38W, although I did not put HDDs asleep when unused (I think this is not possible in a raid setup). I liked the NAS because: the performance was good through gigabit LAN (enough for my needs) power consumption was good its a pretty small case and fits in one of my cupboards I disliked the NAS a bit because: it was a bit noisy, the Q07 case vibrated a good amount because of the HDDs. I switched the NAS off every evening I do not have a real backup of the data on the NAS, only the internal raid 1 as safety. I really dont want to loose my source trees under no circumstances, so I would really be sleeping better if I knew I had regular backups somewhere. Recently, the board seemed to have died, I can't boot anymore. Thus, I was thinking about a redesign of my NAS (I still have to find out what parts are broken, I probably need to replace the mainboard and SSD. HDDs seem to be okay). First of all, I was wondering what other users have as backup for their NAS? Are you actually using a second NAS, and regularly copying over the data to have it safe? Or is there any better solution to this? I was thinking about getting a cheap NAS like the synology DS112j with only one disk, and use rsync or something similar to regularly copy data over to the second NAS (wake the second NAS upon start, shut it down after copy). Although this approach seems somewhat weird, It would have the benefit (?) that I could use a single disk instead of raid in the main NAS, and put the disk asleep when idle, and have the NAS running 24/7 with low energy consumption (I found no way to do this with a gmirror setup). Is there any recommended backup solution for a small NAS? Then I was thinking about a different raid setup. Since I have to buy a new mainboard as well as SSD, I might as well switch over to a i3 board with more ram, and also switch to ZFS. I am not familar with ZFS, I've never used it, but I read and hear much about it. Would it be viable to set up a ZFS storage with only 2 disks? Can I easily extend this storage with more disks, once I choose to add some? I could maybe get a new case like the Fractal Design Array R2 which has more 3,5" slots. I could as well get another 2 disks, but I would prefer sticking with the existing 2 for enegery/heat/noise reasons. Should I go for a ZFS storage or stick to my gmirror setup? I would also like to keep freebsd as operating system, and also I dont need any web gui or something (that is, I dont need/want to use FreeNAS or Openfiler etc). Does anyone maybe have a sample setup in use so I can compare energy consumption/noise/software setup? Any guidance towards the NAS of my dreams (silent, low energy, safe w/ backups) much appreciated.

  Read the article

• Parallel processing slower than sequential?

  - by zebediah49

  EDIT: For anyone who stumbles upon this in the future: Imagemagick uses a MP library. It's faster to use available cores if they're around, but if you have parallel jobs, it's unhelpful. Do one of the following: do your jobs serially (with Imagemagick in parallel mode) set MAGICK_THREAD_LIMIT=1 for your invocation of the imagemagick binary in question. By making Imagemagick use only one thread, it slows down by 20-30% in my test cases, but meant I could run one job per core without issues, for a significant net increase in performance. Original question: While converting some images using ImageMagick, I noticed a somewhat strange effect. Using xargs was significantly slower than a standard for loop. Since xargs limited to a single process should act like a for loop, I tested that, and found it to be about the same. Thus, we have this demonstration. Quad core (AMD Athalon X4, 2.6GHz) Working entirely on a tempfs (16g ram total; no swap) No other major loads Results: /media/ramdisk/img$ time for f in *.bmp; do echo $f ${f%bmp}png; done | xargs -n 2 -P 1 convert -auto-level real 0m3.784s user 0m2.240s sys 0m0.230s /media/ramdisk/img$ time for f in *.bmp; do echo $f ${f%bmp}png; done | xargs -n 2 -P 2 convert -auto-level real 0m9.097s user 0m28.020s sys 0m0.910s /media/ramdisk/img$ time for f in *.bmp; do echo $f ${f%bmp}png; done | xargs -n 2 -P 10 convert -auto-level real 0m9.844s user 0m33.200s sys 0m1.270s Can anyone think of a reason why running two instances of this program takes more than twice as long in real time, and more than ten times as long in processor time to complete the same task? After that initial hit, more processes do not seem to have as significant of an effect. I thought it might have to do with disk seeking, so I did that test entirely in ram. Could it have something to do with how Convert works, and having more than one copy at once means it cannot use processor cache as efficiently or something? EDIT: When done with 1000x 769KB files, performance is as expected. Interesting. /media/ramdisk/img$ time for f in *.bmp; do echo $f ${f%bmp}png; done | xargs -n 2 -P 1 convert -auto-level real 3m37.679s user 5m6.980s sys 0m6.340s /media/ramdisk/img$ time for f in *.bmp; do echo $f ${f%bmp}png; done | xargs -n 2 -P 1 convert -auto-level real 3m37.152s user 5m6.140s sys 0m6.530s /media/ramdisk/img$ time for f in *.bmp; do echo $f ${f%bmp}png; done | xargs -n 2 -P 2 convert -auto-level real 2m7.578s user 5m35.410s sys 0m6.050s /media/ramdisk/img$ time for f in *.bmp; do echo $f ${f%bmp}png; done | xargs -n 2 -P 4 convert -auto-level real 1m36.959s user 5m48.900s sys 0m6.350s /media/ramdisk/img$ time for f in *.bmp; do echo $f ${f%bmp}png; done | xargs -n 2 -P 10 convert -auto-level real 1m36.392s user 5m54.840s sys 0m5.650s

  Read the article

• vlans on openvz, centos 6

  - by arheops

  i have centos 6 with openvz installed on it, switch with vlan support. I need following setup: 1) eth0 on openvz have be tagged multiple vlans. 2) each virtualhost have to be in single vlan. yes,i already read wiki on openvz, but it is just not work. I have on main server interface eth0.108 and able ping address on that interface(using nootbook on untagged port vlan 108), but i not able ping address inside container. Main node: [root@box1 conf]# ifconfig eth0 Link encap:Ethernet HWaddr D0:67:E5:F4:11:60 inet6 addr: fe80::d267:e5ff:fef4:1160/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:506 errors:0 dropped:0 overruns:0 frame:0 TX packets:25 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:68939 (67.3 KiB) TX bytes:1780 (1.7 KiB) Interrupt:16 Memory:c0000000-c0012800 eth0.108 Link encap:Ethernet HWaddr D0:67:E5:F4:11:60 inet addr:10.11.108.3 Bcast:10.11.111.255 Mask:255.255.252.0 inet6 addr: fe80::d267:e5ff:fef4:1160/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:238 errors:0 dropped:0 overruns:0 frame:0 TX packets:19 errors:0 dropped:12 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:25890 (25.2 KiB) TX bytes:926 (926.0 b) eth1 Link encap:Ethernet HWaddr D0:67:E5:F4:11:61 inet addr:192.168.23.233 Bcast:192.168.23.255 Mask:255.255.255.0 inet6 addr: fe80::d267:e5ff:fef4:1161/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:1967 errors:0 dropped:0 overruns:0 frame:0 TX packets:356 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:365298 (356.7 KiB) TX bytes:115007 (112.3 KiB) Interrupt:17 Memory:c2000000-c2012800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:7 errors:0 dropped:0 overruns:0 frame:0 TX packets:7 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:784 (784.0 b) TX bytes:784 (784.0 b) venet0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet6 addr: fe80::1/128 Scope:Link UP BROADCAST POINTOPOINT RUNNING NOARP MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:3 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) veth108.0 Link encap:Ethernet HWaddr 00:18:51:DA:94:D5 inet6 addr: fe80::218:51ff:feda:94d5/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:639 errors:0 dropped:0 overruns:0 frame:0 TX packets:5 errors:0 dropped:1 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:17996 (17.5 KiB) TX bytes:308 (308.0 b) virtual node [root@pbx108 /]# ifconfig eth0.108 Link encap:Ethernet HWaddr 00:18:51:CA:B5:C5 inet addr:10.11.108.1 Bcast:10.11.111.255 Mask:255.255.252.0 inet6 addr: fe80::218:51ff:feca:b5c5/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5 errors:0 dropped:0 overruns:0 frame:0 TX packets:685 errors:0 dropped:2 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:308 (308.0 b) TX bytes:19284 (18.8 KiB) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:683 errors:0 dropped:0 overruns:0 frame:0 TX packets:683 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:76288 (74.5 KiB) TX bytes:76288 (74.5 KiB) /etc/vz/conf/108.conf # RAM PHYSPAGES="0:4000M" # Swap SWAPPAGES="0:512M" # Disk quota parameters (in form of softlimit:hardlimit) DISKSPACE="200G:200G" DISKINODES="20000000:22000000" QUOTATIME="0" # CPU fair scheduler parameter CPUUNITS="4000" VE_ROOT="/vz/root/$VEID" VE_PRIVATE="/vz/private/$VEID" OSTEMPLATE="centos-6-x86_64" ORIGIN_SAMPLE="vswap-256m" NETIF="ifname=eth0.108,mac=00:18:51:CA:B5:C5,host_ifname=veth108.0,host_mac=00:18:51:DA:94:D5" NAMESERVER="8.8.8.8" HOSTNAME="pbx108.localhost" IP_ADDRESS=""

  Read the article

• Asus P8P67 Rev. 3.1 Motherboard issues powering on and saving settings

  - by Scott

  Edit: New Information Have some updated information from the old question below: So basically my issue right now is somewhat similar, but I've been able to rule out a couple of things. I don't think this has anything to do with light on the motherboard. No matter what lights are on/off on the motherboard when the computer is off, they don't affect this issue. The main power LED on the Mobo is always lit when the power supply is turned on, and that's what matters anyway. Even when the main power LED is on, the PC will NOT boot up the first time I hit the power switch. I have to go reset the power supply (make all lights turn off on the Mobo and back on), and THEN hit the power switch. Then everything boots up. Also, the BIOS settings are reset every time this happens. Asus Tech Support told me to try jumping the power with something metal to try and rule out that it's a problem with the connectors getting power, or if it's a problem with the case power switch pins - haven't done that yet though. Any ideas? This is a lot simpler than it was before when I thought it had to do with certain LED indicators for RAM, EPU, etc. Original Question So I built my new desktop just about 3 weeks ago. I've been having a few issues which I think are all related to my motherboard, an Asus P8P67 Revision 3.1, but I'm not 100% sure as this is really the first from-scratch build I've ever done. I've posted these questions on the Asus forums, Asus Tech Support, and the Corsair forums as well as I thought it might have something to do with my power supply at one point. None of these avenues have solved my issue until now completely, so I thought I'd come here to see what you guys think. Here's what's happening: My computer is off, and I go to power it on. I press the power switch on the case (Antec Nine Hundred), and nothing seems to happen. Upon further inspection, I see that what this actually does is simply turn on the EPU LED on my motherboard, but doesn't actually boot anything up. I then have to go and flip the main power switch on the power supply off and back on. What this does is turn off all lights on the Motherboard after a few seconds, and turn them all back on (including the EPU LED that was off before I hit the power switch the first time). Now, hitting the power switch works. The machine boots up fine, and starts going through the boot up process. As a side note: My Motherboard is set to "Force BIOS", and every single time I change this to do the opposite, the next time my computer boots up that change reverts itself. I think this may be due to the fact that I am doing the hard reset on the power supply each time, but I'm not sure. I had thought that the Motherboard would keep its BIOS settings unless you did something to the Mobo itself - so this may be a related issue, or something else completely. That's basically it. Once it's on, it's on. It works fine, recognizes all of my hardware, and runs great. All fans/lights in the case work great, and I'm getting standard readings. The next time I go to shut the computer down however, I can expect the same exact process getting it up and running, including being forced to go into BIOS and exit again before I can load Windows. Another side note: If I power on my computer using the power switch DIRECTLY after shutting it down, it powers right back on (I think this is because the EPU LED light doesn't have time to turn off). It looks as if as long as the EPU LED is lit up on the motherboard before I hit the power switch on the case, the thing will boot up fine (although this doesn't explain the "Force BIOS" issue, at least it's something). Any ideas? Thanks guys. P.S. - System Specs Asus P8P67 Rev. 3.1 Motherboard Intel Core i7 2600K Processor 16GB (4x4GB) G-Skill 1600 RAM NVIDIA EVGA GTX 570 Video Card Crucial 128GB SSD HD Corsair 850W Power Supply Seagate 2TB HDD

  Read the article

• Windows 7 inbuilt and 3rd party (de)fragmentation related queries

  - by Karan

  I have a pretty good idea of how files end up getting fragmented. That said, I just copied ~3,200 files of varying sizes (from a few KB to ~20GB) from an external USB HDD to an internal, freshly formatted (under Windows 7 x64), NTFS, 2TB, 5400RPM, WD, SATA, non-system (i.e. secondary) drive, filling it up 57%. Since it should have been very much possible for each file to have been stored in one contiguous block, I expected the drive to be fragmented not more than 1-2% at most after this rather lengthy exercise (unfortunately this older machine doesn't support USB 3.0). Windows 7's inbuilt defrag utility told me after a quick analysis that the drive was fragmented only 1% or so, which dovetailed neatly with my expectations. However, just out of curiosity I downloaded and ran the latest portable x64 version of Piriform's Defraggler, and was shocked to see the drive being reported as being ~85% fragmented! The portable version of Auslogics Disk Defrag also agreed with Defraggler, and both clearly expected to grind away for ~10 hours to completely defragment the drive. 1) How in blazes could the inbuilt and 3rd party defrag utils disagree so badly? I mean, 10-20% variance is probably understandable, but 1% and 85% are miles apart! This Engineering Windows 7 blog post states: In Windows XP, any file that is split into more than one piece is considered fragmented. Not so in Windows Vista if the fragments are large enough – the defragmentation algorithm was changed (from Windows XP) to ignore pieces of a file that are larger than 64MB. As a result, defrag in XP and defrag in Vista will report different amounts of fragmentation on a volume. ... [Please read the entire post so the quote is not taken out of context.] Could it simply be that the 3rd party defrag utils ignore this post-XP change and continue to use analysis algos similar to those XP used? 2) Assuming that the 3rd party utils aren't lying about the real extent of fragmentation (which Windows is downplaying post-XP), how could the files have even got fragmented so badly given they were just copied over afresh to an empty drive? 3) If vastly differing analysis algos explain the yawning gap, which do I believe? I'm no defrag fanatic for sure, but 85% is enough to make me seriously consider spending 10 hours defragging this drive. On the other hand, 1% reported by Windows' own defragger clearly implies that there is no cause for concern and defragging would actually have negative consequences (as per the post). Is Windows' assumption valid and should I just let it be, or will there be any noticeable performance gains after running one of the 3rd party utils for 10 hours straight? 4) I see that out of the box Windows 7 defrag is scheduled to run weekly. Does anyone know whether it defrags every single time, or only if its analysis reveals a fragmentation percentage over a set threshold? If the latter, what is this threshold and can it be changed, maybe via a Registry edit? Thanks for reading through (my first query on this wonderful site!) and for any helpful replies. Also, if you're answering question #3, please keep in mind that any speed increases post defragging with 3rd party utils vis-à-vis Windows' inbuilt program should not include pre-Vista (preferably pre-Win7) examples. Further, examples of programs that made your system boot faster won't help in this case, since this is a non-system drive (although one that'll still be used daily).

  Read the article

• How to stop windows resizing when the monitor display channel is turned off / switched to different source

  - by Heartspeace

  Have a new 6870 ati radeon adapter with its drivers set to 1080p 60hz resolution hooked up to a 2008 47" high end Samsung HDMI based TV. However, when the tv is turned to a different hdmi input -(when I come back into windows) somehow Windows decides to resize all the open apps to a lower resolution - including some of the side docked hidden pop-outs. When it resizes those though - it just sticked the pop-outs in the middle of the screen and all the resized windows from the open applications in the top left corner - all of them stacked on top of each other and resized to the smaller resolution. The things that seem to be ok after returning are the icons on the desktop, the taskbar, and the sidebar. Anyone have any knowledge of 1) how this happens 2) why it happens 3) how to stop it from resizing the applications and some of the docked pop-outs (they are not really resized after returning - they are just stuck in the middle of the screen approximately where they would be if the right or bottom sidebar should be if the screen was resized to that lower resolution). My hypothesis is that upon losing HDMI signal - that Windows is told by something (driver, or windows itself) that the resolution to be without a signal being present (noting that HDMI signals and handshakes are two way on HDMI devices. If it loses the signal or the tv is switched to another device - then the display adapter must figure that out and tell Windows or figures it out and designs randomly to change the display size). Any and all help is most appreciated. I asked AMD/ATI - but they said they don't know why or how this is happening. I was hoping that maybe this is THE place that the super users truly go to - those that develop display adapter drivers, or that dive deeply into these areas of windows. If there is better sites or just competing sites - please advise - noting I have already written AMD/ATI. HP Response / Additions 4/7/2011 It is really nice to get your reply Shinrai. (BTW is it proper etiquette on these forums to have a discussion?) Yet 'only one issue' - I am using a single display in this case - so Windows doesn't move application windows to another desktop. Windows (or something) decides to shrink the desktop it currently has and resize all windows to the maximum size of the desktop. As such I would be glad if Windows would just keep the current size of the one desktop that is in operation. I also know that this does NOT happen on monitors connected with DVI. There I have had one and two monitors setup and it doesn't resize those screens at all when disconnecting monitors, turning them off, whatever... they stay solid - everything in place - to such an extent that if you forgot the other monitor is off - you will have troubles finding some windows without using one of the control app utilities. So if I could even get the HDMI handling by Windows (or the display driver) ( 1] which is doing this anyway the display driver or Windows - and 2] where is that other resolution size (1024x768) coming from - its not the smallest and its not the largest?) to be having like DVI - Life would be golden (for this aspect anyway). ** found others with same problem in this thread: http://hardforum.com/showthread.php?t=1507324 Thanks, HP

  Read the article

• My computer freezes irregurarly

  - by Manhim

  My computer started to freeze at irregular times for 3 weeks now. What happens My computer freezes, the video stops. (No graphic glitches, it just stops) Sound keeps playing up to some time (Usually 10-30 seconds) then stops playing. Sometimes, randomly, the screen on my G-15 keyboard flickers and I see caracters not at the right places. Usually happens for about 1-2 seconds and a bit before my computer freezes. I have to keep the power button pressed for 4 seconds to shut my computer down. I still hear my hard drives and fans working. Sometimes it works with no problems for a full day, some other times it just keeps freezing each time I restart my computer and I have to leave it for the rest of the day. Sometimes my mouse freezes for a fraction of a second (Like 0.01 to 0.2 seconds) quite randomly, usually before it freezes. No errors spotted by the "Action center" unlike when I had problems with my last video card on this system (Driver errors). My G-15 LCD screen also freezes. What I did so far I have had similar problems in the past and I had changed my hard drive (It was faulty), so I tested my software RAID-0 array and it was faulty so I changed it. (I reinstalled Windows 7 with this part). I also tested with unplugging my secondary hard drive. My CPU was running at about 100 degree Celsius, I removed the dust between the fans and the heatsink and it's now between 50-60. I ran a CPU stress-test and it didn't freeze during the tests (using Prime95 on all cores) Ran a memory test (using memtest86+) for a single pass and there were no errors. Ran a GPU stress test with ati-tools and furmark and it didn't freeze during the tests. (No artefacts either) I had troubles with my graphic card when I got it, but I think that it got fixed with a driver update. I checked the voltages in my BIOS setup and they all seemed ok (±0.2 I think). I have ran on the computer without problems with Fedora 15 on an external hard drive (Appart that it couldn't load Gnome 3 and was reverting to Gnome 2, didn't want to install drivers since I use it on multiple computers) I used it to backup my files from the raid array to my 1TB hard drive for the reinstallation of Windows. (So the crashes only happenned on Windows) [The external hard drive is plugged directly on a SATA port] I contacted EVGA (My graphic card vendor) and pointed them on this question, I'm looking for an answer. Ran sensors on Fedora 15 and got this output: http://pastebin.com/0BHJnAvu When it happens When I play video games (Mostly) When I play flash games (Second most) When I'm looking at my desktop background (It rarely happens when I have a window open, but it does, sometimes) Specs Windows Seven x64 Home Premium Motherboard: M2N-SLI Deluxe CPU: AMD Phenom 9950 x2 @ 2.6GHz Memory: Kingston 4x2GB Dual Channel (Pretty basic memory sticks) Hard drives: Was 2x250GB (Western digital caviar) in raid-0 + 1TB (WD caviar black), I replaced the raid array with a 750GB (WD caviar black) [Yes I removed the array from the raid configurations] 750W Power supply No overcloking. Ever. There have been some power-downs like 4-5 weeks ago, but the problem didn't start immediately after. (I wasn't home, so my computer got shut-down) My current to-try list Change the thermal paste on my CPU. Change my graphic card with a temporary one and stress the computer. Change my power supply. In this situation, how can I successfully pin-point the current hardware problem? (If it's a hardware problem) Because I don't really have the budget to just forget and replace everything. I also don't really have hardware to test-replace current hardware.

  Read the article

• How to use Public IP in case of two ISP when two differs from each other

  - by user1471995

  Please bare with my long explanation but this is important to explain the actual problem. Please also pardon my knowledge with PFsense as i am new to this. I have single PFSense box with 3 Ethernet adapter. Before moving to configuration for these, i want to let you know i have two Ethernet based Internet Leased Line Connectivity let's call them ISP A and ISP B. Then last inetrface is LAN which is connected to network switch. Typical network diagram ISP A ----- PFSense ----> Switch ---- > Servers ISP B ----- ISP A (Initially Purchased) WAN IP:- 113.193.X.X /29 Gateway IP :- 113.193.X.A and other 4 usable public IP in same subnet(So the gateway for those IP are also same). ISP B (Recently Purchased) WAN IP:- 115.115.X.X /30 Gateway IP :- 115.115.X.B and other 5 usable public IP in different subnet(So the gateway for those IP is different), for example if 115.119.X.X2 is one of the IP from that list then the gateway for this IP is 115.119.X.X1. Configuration for 3 Interfaces Interface : WAN Network Port : nfe0 Type : Static IP Address : 113.193.X.X /29 Gateway : 113.193.X.A Interface : LAN Network Port : vr0 Type : Static IP Address : 192.168.1.1 /24 Gateway : None Interface : RELWAN Network Port : rl0 Type : Static IP Address : 115.115.X.X /30 (I am not sure of the subnet) Gateway : 115.115.X.B To use Public IP from ISP A i have done following steps a) Created Virtual IP using either ARP or IP Alias. b) Using Firewall: NAT: Port Forward i have created specific natting from one public IP to my internal Lan private IP for example :- WAN TCP/UDP * * 113.193.X.X1 53 (DNS) 192.168.1.5 53 (DNS) WAN TCP/UDP * * 113.193.X.X1 80 (HTTP) 192.168.1.5 80 (HTTP) WAN TCP * * 113.193.X.X2 80 (HTTP) 192.168.1.7 80 (HTTP) etc., c) Current state for Firewall: NAT: Outbound is Manual and whatever default rule are defined for the WAN those are only present. d) If this section in relevant then for Firewall: Rules at WAN tab then following default rule has been generated. * RFC 1918 networks * * * * * Block private networks * Reserved/not assigned by IANA * * * * * * To use Public IP from ISP B i have done following steps a) Created Virtual IP using either ARP or IP Alias. b) Using Firewall: NAT: Port Forward i have created specific natting from one public IP to my internal Lan private IP for example :- RELWAN TCP/UDP * * 115.119.116.X.X1 80 (HTTP) 192.168.1.11 80 (HTTP) c) Current state for Firewall: NAT: Outbound is Manual and whatever default rule are defined for the RELWAN those are only present. d) If this section in relevant then for Firewall: Rules at RELWAN tab then following default rule has been generated. * RFC 1918 networks * * * * * * Reserved/not assigned by IANA * * * * * * Last thing before my actual query is to make you aware that to have multiple Wan setup i have done following steps a) Under System: Gateways at Groups Tab i have created new group as following MultipleGateway WANGW, RELWAN Tier 2,Tier 1 Multiple Gateway Test b) Then Under Firewall: Rules at LAN tab i have created a rule for internal traffic as follows * LAN net * * * MultipleGateway none c) This setup works if unplug first ISP traffic start routing using ISP 2 and vice-versa. Now my main query and problem is i am not able to use public IP address allocated by ISP B, i have tried many small tweaks but not successful in anyone. The notable difference between the two ISP is a) In case of ISP A there Public usable IP address are on same subnet so the gateway used for the WAN ip is same for the other public IP address. b) In case of ISP B there public usable IP address are on different subnet so the obvious the gateway IP for them is different from WAN gateway's IP. Please let me know how to use ISP B public usable IP address, in future also i am going to rely for more IPs from ISP B only.

  Read the article

• Specifying a Postfix Instance to send outbound email

  - by Catherine Jefferson

  I have a CentOS 6.5 server running Postfix 2.6x (the default distribution) with five public IPv4 IPs bound to it. Each IP has DNS and rDNS set separately. Each uses a different hostname at a different domain. I have five Postfix instances, one bound to each IP, like this example: 192.168.34.104 red.example.com /etc/postfix 192.168.36.48 green.example.net /etc/postfix-green 192.168.36.49 pink.example.org /etc/postfix-pink 192.168.36.50 orange.example.info /etc/postfix-orange 192.168.36.51 blue.example.us /etc/postfix-blue I've tested each IP by telneting to port 25. Postfix answers and banners properly with the correct hostname. Email is received on all of these instances with no problems and is routed to the correct place. This setup, minus the final instance, has existed for a couple of years and works. I never bothered to set up outbound email to go through any but the main instance, however; there was no need. Now I need to send email from blue.example.us that actually leaves from that interface and IP, such that the Received headers show blue.example.us as the sending mailhost, so that SPF and DKIM validate, etc etc. The email that will be sent from blue.example.com is a feedback loop sent by a single shell account on the server (account5), an account that is dedicated to sending this email. The account receives the feedback loop emails from servers on other networks, saves the bodies of those emails, and then generates a new outbound email header, appends the saved body, and sends the email. It's sending by piping each email to sendmail -oi -t. We're doing it this way to mask the identities of the initial servers. The procmail script that processes these emails works correctly. However, I cannot configure this account to send email through the proper Postfix instance/IP/interface. The exact same account and script sends email through the main Postfix instance /etc/postfix without any issues. When I change MAIL_CONFIG to point to /etc/postfix-blue in either .bash_profile or the Procmail script that handles this email, though, I get this error: sendmail: fatal: User account5(###) is not allowed to submit mail I've read the manuals on Postfix.org, searched Google, and tried the suggestions in three previous answers here on ServerFault.com: Postfix - specify interface to deliver outbound mail on Postfix user is not allowed to submit mail Postfix rejects php mails I have been careful to stop and restart Postfix after each configuration change, and tested the results. Nothing has worked. The main postfix instance happily accepts outbound email from account5. The postfix-blue instance continues to reject email from account5 with the sendmail error above. As tempting as it is to blame machine hostility, I know that I must be missing something or doing something wrong. Does anybody have any suggestions as to what it might be? Please feel free to ask for further information about my setup if you need it. =-=-=-=-=-=-=-=-=-= At the request of the responder, here are main.cf and master.cf for a) the main postfix instance ("red.example.com") and b) the FBL instance ("blue.example.us") [NOTE: All parameters not specified below were left at the default Postfix 2.6 settings] MAIN: master.cf smtp inet n - n - - smtpd main.cf myhostname = red.example.com mydomain = example.com inet_interfaces = $myhostname, localhost inet_protocols = all lmtp_host_lookup = native smtp_host_lookup = native ignore_mx_lookup_error = yes mydestination = $myhostname, localhost.$mydomain, localhost local_recipient_maps = mynetworks = 192.168.34.104/32 relay_domains = example.com, example.info, example.net, example.org, example.us relayhost = [192.168.34.102] # Separate physical server, main mailserver. relay_recipient_maps = hash:/etc/postfix/relay_recipients alias_maps = hash:/etc/aliases alias_database = hash:/etc/aliases smtpd_banner = $myhostname ESMTP $mail_name multi_instance_wrapper = ${command_directory}/postmulti -p -- multi_instance_enable = yes multi_instance_directories = /etc/postfix-green /etc/postfix-pink /etc/postfix-orange /etc/postfix-blue FBL: master.cf 184.173.119.103:25 inet n - n - - smtpd main.cf myhostname = blue.example.us mydomain = blue.example.us <= Deliberately set to subdomain only. myorigin = $mydomain inet_interfaces = $myhostname lmtp_host_lookup = native smtp_host_lookup = native ignore_mx_lookup_error = yes mydestination = $myhostname local_recipient_maps = unix:passwd.byname $alias_maps $virtual_alias_maps mynetworks = 192.168.36.51/32, 192.168.35.20/31 <= Second IP is backup MX servers relay_domains = $mydestination recipient_canonical_maps = hash:/etc/postfix-blue/canonical virtual_alias_maps = hash:/etc/postfix-fbl/virtual alias_maps = hash:/etc/aliases, hash:/etc/postfix-blue/canonical alias_maps = hash:/etc/aliases, hash:/etc/postfix-blue/canonical mailbox_command = /usr/bin/procmail -a "$EXTENSION" DEFAULT=$HOME/Mail/ MAILDIR=$HOME/Mail smtpd_banner = $myhostname ESMTP $mail_name authorized_submit_users = multi_instance_name = postfix-blue multi_instance_enable = yes

  Read the article

• Too many Bind query (cache) denied, DNS attack?

  - by Jake

  Once Bind crashed and I did: tail -f /var/log/messages I see a massive number of logs every second. Is this a DNS attack? or is there something wrong? Sometimes I see a domain in logs like this: dOmAin.com (upper and lower). As you see there is only one single domain in the logs with different IPs Oct 10 02:21:26 mail named[20831]: client 74.125.189.18#38921: query (cache) 'ns1.domain2.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 192.221.144.171#38833: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 74.125.189.17#42428: query (cache) 'ns2.domain2.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 192.221.146.27#37899: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 193.203.82.66#39263: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 8.0.16.170#59723: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 80.169.197.66#32903: query (cache) 'dOmAin.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 134.58.60.1#47558: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 192.221.146.34#47387: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 8.0.16.8#59392: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 74.125.189.19#64395: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 217.72.163.3#42190: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 83.146.21.252#22020: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 192.221.146.116#57342: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 193.203.82.66#52020: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 8.0.16.72#64317: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 80.169.197.66#31989: query (cache) 'dOmAin.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 74.125.189.18#47436: query (cache) 'ns2.domain2.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 74.125.189.16#44005: query (cache) 'ns1.domain2.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 85.132.31.10#50379: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 94.241.128.3#60106: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 85.132.31.10#59118: query (cache) 'domain.com/A/IN' denied Oct 10 02:21:26 mail named[20831]: client 212.95.135.78#27811: query (cache) 'domain.com/A/IN' denied /etc/resolv.conf ; generated by /sbin/dhclient-script nameserver 4.2.2.4 nameserver 8.8.4.4 Bind config: // generated by named-bootconf.pl options { directory "/var/named"; /* * If there is a firewall between you and nameservers you want * to talk to, you might need to uncomment the query-source * directive below. Previous versions of BIND always asked * questions using port 53, but BIND 8.1 uses an unprivileged * port by default. */ // query-source address * port 53; allow-transfer { none; }; allow-recursion { localnets; }; //listen-on-v6 { any; }; notify no; }; // // a caching only nameserver config // controls { inet 127.0.0.1 allow { localhost; } keys { rndckey; }; }; zone "." IN { type hint; file "named.ca"; }; zone "localhost" IN { type master; file "localhost.zone"; allow-update { none; }; }; zone "0.0.127.in-addr.arpa" IN { type master; file "named.local"; allow-update { none; }; };

  Read the article

• Issues Converting Plain Text Into Microsoft Word Bulleted Lists

  - by user787832

  I'm a programmer. I hate status reports. I found a way to live with it. While I am working in my IDE ( Visual Slickedit ) I keep a plain text file open in one of the file/buffer tabs. As I finish things I just jot down a quick note into that file. At the end of the week that becomes my weekly status report. Example entries: The Datatables.net plugin runs very slowly in IE 8 with more than 2,000 records. I changed the way I did the server side code to process the data to make less work for the plugin to get decent performance for the IE 8 users. I made a class to wrap data from the new data collection objects into the legacy data holder objects. This will let the new database code be backward compatible with the legacy code until we can replace it. I found the bug reported by Jane. The software is fine. The database we use for the test site has data that is corrupted in a way it wouldn't be for production site At the end of the month I go back to each weekly *.txt file and paste all of the entries into a MS Word file for a monthly report. I give the monthly report to a liason to the contracting company who has to compile everyone's monthly reports into a single MS Word 2007 document. His problem, soon to be my problem, comes when he highlights my paragraphs like the ones above to put bullets in front of my paragraphs. When he highlights my notes to put bullets in front of them with MS Word 2007, Word rearranges the text a bit and the new line chars/carriage returns stagger the text so the text is no longer in neat chunks. This: I found the bug reported by Jane. The software is fine. The database we use for the test site has data that is corrupted in a way it wouldn't be for production site Becomes This: I found the bug reported by Jane. The software is fine. The database we use for the test site has data that is corrupted in a way it wouldn't be for production site I tried turning word wrap on in my IDE for the text files I put my status notes in. It just puts some kind of newline character in anyway. Searching/Replacing those chars in the text files has the result of destroying the paragraphs. Once my notes are pasted into MS Word, Word automatically translates them into paragraph breaks. Searching/Replacing them there has similar results. Blank lines separating the notes disappears. One big mess. What I would like is to be able to keep adding my status notes to a text file as I am now, but do something different when I paste the notes into MS Word such that my liason can select the text, hit the bulleting command and NOT have the staggered text as shown above. Any ideas? Thanks much in advance Steve

  Read the article

• Choice of an OS for a home ZFS NAS

  - by OlafM

  I am preparing a home NAS with an old Athlon 64 X2 3800+, 4 GB ECC RAM, Asus M2V MX motherboard, and a single 3 TB WDC Green (another one as mirror may be installed in the future). It's the cheapest solution I found that includes ECC memory and the higher energy consumption is offset by the lower (zero) cost of acquisition. The system will be used for: music storage and stream to other desktop computers; storage of the scanned dia slides (3-4k slides, 180 MB TIFF each one plus reduced quality JPEG version); stream of these photos to a local iPad 2 (maybe Plex App? not yet sure); (one additional) remote backup via rsync/ssh or ZFS send/receive. It will be controlled via remote ssh, maybe VNC, no monitor attached. Absolute requirement is a reliable ZFS solution, plus the ability to easily install packets/software/virtual machines and to update remotely (I will be the admin and I don't live near the NAS). I have mainly three options: NAS4free/FreeNAS OpenIndiana Solaris Express 11 (yeah yeah I know the license requirements, I will write a perl script on it to count it as development machine). Problems: NAS4free/FreeNAS (I tested only NAS4free) required embedded installation for remote upgrading, but full install for easy addition of software packets. Since I need at least AirVideo Server (linux/win) and Plex App (win/linux) to stream the photos and some videos to iPad (they both require virtualbox), but I cannot be there to install updates, NAS4free/FreeNAS are excluded. http://www.nas4free.org/general_information.html explains the issue: embedded can be remotely updated, full cannot. Solaris has also another advantage: Crashplan client supports Solaris and I'm already using it for other backups. I would like to leave the option open, even if I will be doing backups probably through zfs send/receive. NexentaStor was left out because zfs send/receive are not included in the free version. The question is now Solaris 11 Express over OpenIndiana. To ease the management, I will be using http://www.napp-it.org Which one would you suggest and why? I found lots of informations and it's difficult for me to decide. I think (from the napp-it manual) that Solaris has some additional options for SMB shares, but are they really needed at home? I think I won't even use ACLs, since normal unix-style permissions are enough. OpenIndiana has maybe more frequent updates (Solaris offers only security updates between releases), but again, do I need them? I don't think so. Moreover, this is a NAS that has to work and nothing else, I cannot risk having problems that require me to access the server. Isn't OpenIndiana a bit more... cutting edge (in the Solaris world)? I'm just asking, no need to focus on this for the answer :-) I would limit myself to these two options (SE11.1/OI) also because I will be making a NAS for me in the future (where high performances with Mac shares are also required) and Solaris has kernel support for AFP. I will use this server to gather experience as well. After this long question, thanks in advance! If you need additional info, let me know and I will update this post. UPDATES Given the first answers, I will strongly suggest the person paying the hardware to insert a second HD. Better 2x2TB than 1x3TB (3 TB is oversized anyway). I was trying to keep the initial costs down to spread them over a longer period, but better having something good from the beginning.

  Read the article

• Configuring a PIX 506e for Asterisk

  - by orthogonal3

  Hi all! I'm having problems configuring a old Cisco PIX running 6.3 and wondered if anyone can lend a hand? Simply put I have a PIX 506e that I want to put in my VoIP data path. I can't update it and getting a compat version of Java for that version of PIX is tough so I can't log onto the web interface. The PIX straddles two networks..... 192.168.5.0 on the inside, ...50.0 on the outside both net masks are 255.255.255.0 I have a local Asterisk server cluster with a single service IP (<local asterisk>) SIP is on UDP 5060 and RTP (for the voip data) is on UDP 18000-18999 I know thats a big range but hey may as well. I need the 192.168.5.0 net to have web and ftp access for updates and the like. DHCP, DNS and NTP is already provided on that network so I don't need external DNS access. So I think I want the following rules: SIP or RTP from <my itsp> arriving at <outside voip ip> NATed to <local asterisk> SIP or RTP able to do the reverse route (should be covered by high sec - low sec??) HTTP and FTP access outbound for software update for the servers etc I have the following config at the minute - and I think I'm almost there (I hope)... interface ethernet0 auto interface ethernet1 auto nameif ethernet0 outside security0 nameif ethernet1 inside security100 enable password wouldyouliketobeapeppertoo encrypted passwd wouldyouliketobeapeppertoo encrypted hostname afirewall domain-name adomain fixup protocol dns maximum-length 512 fixup protocol ftp 21 fixup protocol h323 h225 1720 fixup protocol h323 ras 1718-1719 fixup protocol http 80 fixup protocol rsh 514 fixup protocol rtsp 554 fixup protocol sip 5060 fixup protocol sip udp 5060 fixup protocol skinny 2000 fixup protocol smtp 25 fixup protocol sqlnet 1521 fixup protocol tftp 69 access-list acl_ping permit icmp any any access-list voip permit ip host <my itsp> host <local asterisk> mtu outside 1500 mtu inside 1500 ip address outside <outside pix ip> 255.255.255.0 ip address inside <inside pix ip> 255.255.255.0 arp timeout 14400 global (outside) 1 <outside generic ip> nat (inside) 1 192.168.5.0 255.255.255.0 0 0 static (inside,outside) <outside voip ip> <local asterisk> netmask 255.255.255.255 0 0 static (outside,inside) <local asterisk> <outside voip ip> netmask 255.255.255.255 0 0 access-group acl_ping in interface outside access-group acl_ping in interface inside route outside 0.0.0.0 0.0.0.0 <my next hop router> 1 route outside <my itsp> 255.255.255.255 <my next hop router> 1 I think I just need a hand with the access-lists and NAT/static rules. Would anyone be able to help as I've RTFM'd the Cisco docs a few times and they're heavy. Wishing I'd completed my CCNA now! Thanks all for any help, Phil

  Read the article

• Optimise Apache for EC2 micro instance

  - by Shiyu Sekam

  I'm running apache2 on a EC2 micro instance with ~600 mb RAM. The instance was running for almost a year without problems, but in the last weeks it just keeps crashing, because the server reached MaxClients. The server basically runs few websites, one wordpress blog(not often used), company website(most used) and 2 small sites, which are just internal. The database for the blog runs on RDS, so there's no Mysql running on this web server. When I came to the company, the server already was setup and is running apache + mod_php + prefork. We want to migrate that in the future to a nginx + php-fpm, but it still needs further testing. So for now I have to stick with the old setup. I also use CloudFlare DDOS protection in front of the server, because it was attacked a couple of the times in the last weeks. My company don't want to pay money for a better web server at this point, so I have to stick with the micro instance also. Additionally the code for the website we run is really bad and slow and sometimes a single page load can take up to 15 seconds. The whole website is dynamic and written in PHP, so caching isn't really an option here. It's a customized search for users. I've already turned off KeepAlive, which improved the performance a little bit. My prefork config looks like the following: StartServers 2 MinSpareServers 2 MaxSpareServers 5 ServerLimit 10 MaxClients 10 MaxRequestsPerChild 100 The server just becomes unresponsive after a while running and I've run the following command to see how many connections there are: netstat | grep http | wc -l 75 Trying to restart apache helps for a short moment, but after that a while the apache process(es) become unresponsive again. I've the following modules enabled(output of apache2ctl -M) Loaded Modules: core_module (static) log_config_module (static) logio_module (static) version_module (static) mpm_prefork_module (static) http_module (static) so_module (static) alias_module (shared) authz_host_module (shared) deflate_module (shared) dir_module (shared) expires_module (shared) mime_module (shared) negotiation_module (shared) php5_module (shared) rewrite_module (shared) setenvif_module (shared) ssl_module (shared) status_module (shared) Syntax OK apache2.conf # Security ServerTokens OS ServerSignature On TraceEnable On ServerName "web.example.com" ServerRoot "/etc/apache2" PidFile ${APACHE_PID_FILE} Timeout 30 KeepAlive off User www-data Group www-data AccessFileName .htaccess <Files ~ "^\.ht"> Order allow,deny Deny from all Satisfy all </Files> <Directory /> Options FollowSymLinks AllowOverride None </Directory> DefaultType none HostnameLookups Off ErrorLog /var/log/apache2/error.log LogLevel warn EnableSendfile On #Listen 80 Include /etc/apache2/mods-enabled/*.load Include /etc/apache2/mods-enabled/*.conf Include /etc/apache2/ports.conf LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %b" common LogFormat "%{Referer}i -> %U" referer LogFormat "%{User-agent}i" agent Include /etc/apache2/conf.d/*.conf Include /etc/apache2/sites-enabled/*.conf Vhost of main site <VirtualHost *:80> ServerName www.example.com ## Vhost docroot DocumentRoot /srv/www/jenkins/Web ## Directories, there should at least be a declaration for /srv/www/jenkins/Web <Directory /srv/www/jenkins/Web> AllowOverride All Order allow,deny Allow from all </Directory> ## Load additional static includes ## Logging ErrorLog /var/log/apache2/www.example.com.error.log LogLevel warn ServerSignature Off CustomLog /var/log/apache2/www.example.com.access.log combined ## Rewrite rules RewriteEngine On RewriteCond %{HTTP_HOST} !^www.example.com$ RewriteRule ^.*$ http://www.example.com%{REQUEST_URI} [R=301,L] ## Server aliases ServerAlias www.example.invalid ServerAlias example.com ## Custom fragment <Location /srv/www/jenkins/Web/library> Order Deny,Allow Deny from all </Location> <Files ~ "^\.(.+)"> Order deny,allow deny from all </Files> </VirtualHost>

  Read the article

• Mod_Rewrite w Apache mod_jrun22.so & ColdFusion 9 on cPanel

  - by Eddie B

  How can I utilize mod_rewrite at either the httpd.conf level or per-directory level when mod_jrun22 seems to have short-stopped the rewrite process for ColdFusion pages? I have a ColdFusion 9 based site running on Centos 5.8 w cPanel. cPanel uses EasyApache 3 to manage virtual host containers and as such the conf for mod_jrun22.so, /usr/local/apache/conf/includes/pre_main_global.conf, is loaded prior to the main httpd.conf with the domain specific rules for the container. My assertion is that .cfm pages are failing to be rewritten due to the mod_jk22.so module having priority in the directive chain. To note, I also have a WordPress blog in the site where the rewrites appear to be working fine. For example the following code to remove the index file works fine for php and fails with cfm ... .htaccess under /blog/ : This works Options -Indexes -Multiviews <IfModule mod_rewrite.c> RewriteEngine On RewriteBase /blog/ RewriteRule ^index\.php$ - [L] RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule . /blog/index.php [L] </IfModule> .htaccess under / : This does not work as expected. Apache serves the page. ASSERT: This would redirect to domain.com/ without index.cfm Options -Indexes -Multiviews <IfModule mod_rewrite.c> RewriteEngine On RewriteBase / RewriteRule ^index\.cfm$ - [L] RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{REQUEST_FILENAME} !-d RewriteRule . /index.cfm [L] </IfModule> .htaccess under / : This works I'm presuming this is working because the redirect is to another .cfm page and a 404 handler in Application.cfc ... Options -Indexes -Multiviews <IfModule mod_rewrite.c> RewriteEngine On RewriteBase / RewriteRule ^.*\.cfm$ - [L] RewriteCond %{REQUEST_FILENAME} !-d RewriteCond %{REQUEST_FILENAME} !-f RewriteCond %{ENV:REDIRECT_STATUS} =404 RewriteRule . /404.cfm$ [L] </IfModule> I've attempted numerous different methods to rewrite .cfm urls ... Adding [PT], [L], [R], [NS], Moving the script to Directory blocks under httpd.conf --- all with the same results ... either the rewrite doesn't work or Apache crashes in an endless loop ... Any help would be greatly appreciated. Below is a single-visit rewrite log snippet for a request to /index.cfm ... the pass-through is taking effect before the rewrite ... cat rewrite_dump_mod | grep index.cfm [perdir /home/foo/public_html/] strip per-dir prefix: /home/foo/public_html/index.cfm -> index.cfm [perdir /home/foo/public_html/] applying pattern '^.*\.cfm$' to uri 'index.cfm' [perdir /home/foo/public_html/] pass through /home/foo/public_html/index.cfm [perdir /home/foo/public_html/] strip per-dir prefix: /home/foo/public_html/index.cfm -> index.cfm [perdir /home/foo/public_html/] applying pattern '^.*\.cfm$' to uri 'index.cfm' [perdir /home/foo/public_html/] pass through /home/foo/public_html/index.cfm * UPDATE * I've managed to figure this out ... it took a while ... Options -Indexes -Multiviews +FollowSymLinks <IfModule mod_rewrite.c> RewriteEngine On RewriteBase / RewriteCond %{HTTP_HOST} !^www\. RewriteRule ^(.*)$ http://www.%{HTTP_HOST}/$1 [R=301,L] RewriteCond %{THE_REQUEST} ^.*/index\.cfm RewriteRule ^(.*)index.cfm http://%{HTTP_HOST}/$1 [R=301,L] </IfModule>

  Read the article

• Ubuntu Server, 2 Ethernet Devices, Same Gateway - Want to force internet traffic through 1 device (or at least allow it to work!)

  - by Chris Drumgoole

  I have a Ubuntu 10.04 Server with 2 ethernet devices, eth0 and eth1. eth0 has a static IP of 192.168.1.210 eth1 has a static IP if 192.168.1.211 The DHCP server (which also serves as the internet gateway) sits at 192.168.1.1. The issue I have right now is when I have both plugged in, I can connect to both IPs over SSH internally, but I can't connect to the internet from the server. If I unplug one of the devices (e.g. eth1), then it works, no problem. (Also, I get the same result when I run sudo ifconfig eth1 down). Question, how can I configure it so that I can have both devices eth0 and eth1 play nice on the same network, but allow internet access as well? (I am open to either enforcing all inet traffic going through a single device, or through both, I'm flexible). From my google searching, it seems I could have a unique (or not popular) problem, so haven't been able to find a solution. Is this something that people generally don't do? The reason I want to make use of both ethernet devices is because I want to run different local traffic services on on both to split the load, so to speak... Thanks in advance. UPDATE Contents of /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet dhcp # The secondary network interface #auto eth1 #iface eth1 inet dhcp (Note: above, I commented out the last 2 lines because I thought that was causing issues... but it didn't solve it) netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.1.0 192.168.1.1 255.255.255.0 UG 0 0 0 eth0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0 UPDATE 2 I made a change to the /etc/network/interfaces file as suggested by Kevin. Before I display the file contents and the route table, when I am logged into the server (through SSH), I can not ping an external server, so this is the same issue I was experiencing that led to me posting this question. I ran a /etc/init.d/networking restart after making the file changes. Contents of /etc/network/interfaces: # The loopback network interface auto lo iface lo inet loopback # The primary network interface auto eth0 iface eth0 inet dhcp address 192.168.1.210 netmask 255.255.255.0 gateway 192.168.1.1 # The secondary network interface auto eth1 iface eth1 inet dhcp address 192.168.1.211 netmask 255.255.255.0 ifconfig output eth0 Link encap:Ethernet HWaddr 78:2b:cb:4c:02:7f inet addr:192.168.1.210 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::7a2b:cbff:fe4c:27f/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:6397 errors:0 dropped:0 overruns:0 frame:0 TX packets:683 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:538881 (538.8 KB) TX bytes:85597 (85.5 KB) Interrupt:36 Memory:da000000-da012800 eth1 Link encap:Ethernet HWaddr 78:2b:cb:4c:02:80 inet addr:192.168.1.211 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::7a2b:cbff:fe4c:280/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5799 errors:0 dropped:0 overruns:0 frame:0 TX packets:8 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:484436 (484.4 KB) TX bytes:1184 (1.1 KB) Interrupt:48 Memory:dc000000-dc012800 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:635 errors:0 dropped:0 overruns:0 frame:0 TX packets:635 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:38154 (38.1 KB) TX bytes:38154 (38.1 KB) netstat -rn Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth1 0.0.0.0 192.168.1.1 0.0.0.0 UG 0 0 0 eth0

  Read the article

• mySQL Optimization Suggestions

  - by Brian Schroeter

  I'm trying to optimize our mySQL configuration for our large Magento website. The reason I believe that mySQL needs to be configured further is because New Relic has shown that our SELECT queries are taking a long time (20,000+ ms) in some categories. I ran MySQLTuner 1.3.0 and got the following results... (Disclaimer: I restarted mySQL earlier after tweaking some settings, and so the results here may not be 100% accurate): >> MySQLTuner 1.3.0 - Major Hayden <[email protected]> >> Bug reports, feature requests, and downloads at http://mysqltuner.com/ >> Run with '--help' for additional options and output filtering [OK] Currently running supported MySQL version 5.5.37-35.0 [OK] Operating on 64-bit architecture -------- Storage Engine Statistics ------------------------------------------- [--] Status: +ARCHIVE +BLACKHOLE +CSV -FEDERATED +InnoDB +MRG_MYISAM [--] Data in MyISAM tables: 7G (Tables: 332) [--] Data in InnoDB tables: 213G (Tables: 8714) [--] Data in PERFORMANCE_SCHEMA tables: 0B (Tables: 17) [--] Data in MEMORY tables: 0B (Tables: 353) [!!] Total fragmented tables: 5492 -------- Security Recommendations ------------------------------------------- [!!] User '@host5.server1.autopartsnetwork.com' has no password set. [!!] User '@localhost' has no password set. [!!] User 'root@%' has no password set. -------- Performance Metrics ------------------------------------------------- [--] Up for: 5h 3m 4s (5M q [317.443 qps], 42K conn, TX: 18B, RX: 2B) [--] Reads / Writes: 95% / 5% [--] Total buffers: 35.5G global + 184.5M per thread (1024 max threads) [!!] Maximum possible memory usage: 220.0G (174% of installed RAM) [OK] Slow queries: 0% (6K/5M) [OK] Highest usage of available connections: 5% (61/1024) [OK] Key buffer size / total MyISAM indexes: 512.0M/3.1G [OK] Key buffer hit rate: 100.0% (102M cached / 45K reads) [OK] Query cache efficiency: 66.9% (3M cached / 5M selects) [!!] Query cache prunes per day: 3486361 [OK] Sorts requiring temporary tables: 0% (0 temp sorts / 812K sorts) [!!] Joins performed without indexes: 1328 [OK] Temporary tables created on disk: 11% (126K on disk / 1M total) [OK] Thread cache hit rate: 99% (61 created / 42K connections) [!!] Table cache hit rate: 19% (9K open / 49K opened) [OK] Open file limit used: 2% (712/25K) [OK] Table locks acquired immediately: 100% (5M immediate / 5M locks) [!!] InnoDB buffer pool / data size: 32.0G/213.4G [OK] InnoDB log waits: 0 -------- Recommendations ----------------------------------------------------- General recommendations: Run OPTIMIZE TABLE to defragment tables for better performance MySQL started within last 24 hours - recommendations may be inaccurate Reduce your overall MySQL memory footprint for system stability Enable the slow query log to troubleshoot bad queries Increasing the query_cache size over 128M may reduce performance Adjust your join queries to always utilize indexes Increase table_cache gradually to avoid file descriptor limits Read this before increasing table_cache over 64: http://bit.ly/1mi7c4C Variables to adjust: *** MySQL's maximum memory usage is dangerously high *** *** Add RAM before increasing MySQL buffer variables *** query_cache_size (> 512M) [see warning above] join_buffer_size (> 128.0M, or always use indexes with joins) table_cache (> 12288) innodb_buffer_pool_size (>= 213G) My my.cnf configuration is as follows... [client] port = 3306 [mysqld_safe] nice = 0 [mysqld] tmpdir = /var/lib/mysql/tmp user = mysql port = 3306 skip-external-locking character-set-server = utf8 collation-server = utf8_general_ci event_scheduler = 0 key_buffer = 512M max_allowed_packet = 64M thread_stack = 512K thread_cache_size = 512 sort_buffer_size = 24M read_buffer_size = 8M read_rnd_buffer_size = 24M join_buffer_size = 128M # for some nightly processes client sessions set the join buffer to 8 GB auto-increment-increment = 1 auto-increment-offset = 1 myisam-recover = BACKUP max_connections = 1024 # max connect errors artificially high to support behaviors of NetScaler monitors max_connect_errors = 999999 concurrent_insert = 2 connect_timeout = 5 wait_timeout = 180 net_read_timeout = 120 net_write_timeout = 120 back_log = 128 # this table_open_cache might be too low because of MySQL bugs #16244691 and #65384) table_open_cache = 12288 tmp_table_size = 512M max_heap_table_size = 512M bulk_insert_buffer_size = 512M open-files-limit = 8192 open-files = 1024 query_cache_type = 1 # large query limit supports SOAP and REST API integrations query_cache_limit = 4M # larger than 512 MB query cache size is problematic; this is typically ~60% full query_cache_size = 512M # set to true on read slaves read_only = false slow_query_log_file = /var/log/mysql/slow.log slow_query_log = 0 long_query_time = 0.2 expire_logs_days = 10 max_binlog_size = 1024M binlog_cache_size = 32K sync_binlog = 0 # SSD RAID10 technically has a write capacity of 10000 IOPS innodb_io_capacity = 400 innodb_file_per_table innodb_table_locks = true innodb_lock_wait_timeout = 30 # These servers have 80 CPU threads; match 1:1 innodb_thread_concurrency = 48 innodb_commit_concurrency = 2 innodb_support_xa = true innodb_buffer_pool_size = 32G innodb_file_per_table innodb_flush_log_at_trx_commit = 1 innodb_log_buffer_size = 2G skip-federated [mysqldump] quick quote-names single-transaction max_allowed_packet = 64M I have a monster of a server here to power our site because our catalog is very large (300,000 simple SKUs), and I'm just wondering if I'm missing anything that I can configure further. :-) Thanks!

  Read the article

• How to use iptables to forward all data from an IP to a Virtual Machine

  - by jro

  OK, in an attempt to get some response, a TL;DR version. I know that the following command: iptables -A PREROUTING -t nat -i eth0 --dport 80 --source 1.1.1.1 -j REDIRECT --to-port 8080 ... will redirect all traffic from port 80 to port 8080. The problem is that I have to do this for every port that is to be redirected. To be future-proof, I want all ports for an IP to be redirected to a different (internal) IP, so that if one might decide to enable SSH, they can directly connect without worrying about iptables. What is needed to reliable forward all traffic from an external IP, to an internal IP, and vice versa? Extended version I've scoured the internet for this, but I never got a solid answer. What I have is one physical server (HOST), with several virtual machines (VM) that need traffic redirected to them. Just getting it to work with a single machine is enough for now. The VM's run under VirtualBox, and are set to use a host-only adapter (vboxnet0). Everything seems to work, but it is greatly lagging. Both the host (CentOS 5.6) and the guest (Ubuntu 10.04) machine are running Linux. What I did was the following: Configure the VM to have a static IP in the network of the vboxnet0 adapter. Add an IP alias to the host, registering to the dedicated (outside) IP. Setup iptables to allow traffic to come through (via sysctl). Configure iptables to DNAT and SNAT data from a given IP address to the internal address. iptables commands: sudo iptables -A FORWARD -m conntrack --ctstate ESTABLISHED,RELATED -j ACCEPT sudo iptables -A POSTROUTING -t nat -j MASQUERADE iptables -t nat -I PREROUTING -d $OUT_IP -I eth0 -j DNAT --to-destination $IN_IP iptables -t nat -I POSTROUTING -s $IN_IP -o eth0 -j SNAT --to-source $OUT_IP Now the site works, but is really, really slow. I'm hoping I missed something simple, but I'm out of ideas for now. Some background info: before this, the site was working with basic port forwarding. E.g. port 80 was mapped to port 8080 using iptables. In VirtualBox (having the network adapter configured as NAT), a port forwarding the other way around made things work beautifully. The problem was twofold: first, multiple ports needed to be forwarded (for admin interfaces, https, ssh, etc). Second, it only allowed one IP address to use port 80. To resolve things, multiple external IP addresses are used for different (sub)domains. Likewise, the "VirtualBox" network will contain the virtual machines: DNS Ext. IP Adapter VM "VirtalBox" IP ------------------------------------------------------------------ a.example.com 1.1.1.1 eth0:1 vm_guest_1 192.168.56.1 b.example.com 2.2.2.2 eth0:2 vm_guest_2 192.168.56.2 c.example.com 3.3.3.3 eth0:3 vm_guest_3 192.168.56.3 And so on. Put simply, the goal is to channel all traffic from a.example.com to vm_guest_1 (of put differently, from 1.1.1.1 to 192.168.56.1). And achieve this with an acceptable speed :).

  Read the article

< Previous Page | 631 632 633 634 635 636 637 638 639 640 641 642  | Next Page >