Search Results

Search found 2840 results on 114 pages for 'ports'.

Page 64/114 | < Previous Page | 60 61 62 63 64 65 66 67 68 69 70 71  | Next Page >

• Using 4 monitors with 2 generic video cards... possible?

  - by Ikram

  I'm thinking of setting up 4 monitors in a grid, using two video cards, one card to feed each pair of monitors through the card's two DVI ports. The most important requirement for me is to have the grid of monitors act as one single huge screen. Is this scenario possible by using two generic cards like Radeon 4870s on a Windows 7 computer? (I've heard of Eyefinity, but 4870s don't have it) Another issue is that I only have one PCI-Express slot on my computer's motherboard, therefore I'll need to use one of the lesser PCI cards as the second video card. Will this pose problems?

  Read the article

• Hp Procurve Switch : port filtered

  - by user117140

  My HP Procurve switch is blocking port 22 and I dont know how to unblock it.Please let me know From the server, see port 22 is blocked [root@server ~]#nmap -p22,80,443 10.247.172.70 Starting Nmap 4.11 ( http://www.insecure.org/nmap/ ) at 2012-04-16 14:12 IST mass_dns: warning: Unable to determine any DNS servers. Reverse DNS is disabled. Try using --system-dns or specify valid servers with --dns_servers Interesting ports on 10.247.172.70: PORT STATE SERVICE 22/tcp filtered ssh ------------------> see 80/tcp filtered http 443/tcp filtered https This is blocked on cisco switch but I dont have any clue how this is done. I know that vlan is configured on switch. vlan 54 ip ospf 10.247.172.65 area 0.0.0.10 vrrp vrid 54 owner virtual-ip-address 10.247.172.65 255.255.255.192 priority 255 enable exit exit Please let me know how to unblock ssh port 22 access on this switch?

  Read the article

• iSCSI SAN RAID 10 Performance -- Poor Read, Good Write

  - by Litzner

  I have a EqualLogic PS4000 SAN unit with the latest firmware, setup in RAID 10. I have 3 2TB Volumes on the SAN shared out via iSCSI on 2 eth ports on two different subnets. I have moved a test server over to this newly setup SAN, and my testing is showing me a problem. I am getting dismal read performance in everything except a test with 32 queue depth (see attach image) Write performance seems to be right about where it should be. I have tried MPIO on and off, on was slightly better but not much.

  Read the article

• Forward requests to IIS Application/Folder to Apache server on another port

  - by TheGwa

  I have found many questions and answers for ways of doing this using asapi filters or ARR and URL Rewrite, but none are clear and concise and I am sure many people have this issue. I am looking for a best practice step by step solution to the following scenario: I have a development server accessible externally via a specific port for testing. Eg. rnd.domain.com:8888. So there is one port in and out of this machine accessible to the world. On this server I have a number of Apache or other servers using specific ports such as 8080. IIS is bound to port 80 locally as well as 8888 to get external requests and works perfectly. I would like to use an application (folder) in IIS such as rnd.domain.com:8888/mapserver to map to the local apache server in both directions. The same solution must apply in production where the domain is mapped to port 80. eg. production.domain.com/mapserver maps to 8080 on production server

  Read the article

• Access VirtualBox-ed server from behind the router

  - by migajek

  I'm having the following configuration: Windows 7 hosting VirtualBox and it's guest: Ubuntu The machine (physical) which runs VirtualBox is behind the router and has the address of 192.168.0.110 VirtualBox runs the Bridged network, and the IP of VirtualBox-ed Ubuntu (eth0) is 192.168.0.200 Host (Win7) is running HTTP service on port 80, while guest (Ubuntu) is running it's service on port 9000 I can access both services from inside the network by typing the ip_address:port and this works fine. Both ports are forwarded on the router to their's respective IPs: 80 -> 192.168.0.110:80 9000 -> 192.168.0.200:9000 Unfortunately, accessing the router's external IP doesn't work as expected. While external_ip:80 works correctly, external_ip:9000 - doesn't I believe the problem is VBox - related, since the same network is running also other physical machine with Ubuntu and http service on 8000 and this one is forwarded correctly.

  Read the article

• Exchange Server 2010 does not include WebDAV

  - by CNLSH

  This is the 1st time I'm dealing with server. May I know what does it mean by "Exchange Server 2010 does not include WebDAV"? Does this mean that EWS does not use HTTPWebRequest and HTTPWebResponse anymore or does not communicates by using the same ports that HTTP and HTTPS? Is it some setting done at the server side that disable the use of WebDav? When it said does not include WebDAV, what does it actually mean? If i really want to use WebDav in Exchange Server 2010, is it possible? Yes, EWS is way better compared to WebDav but what if I wish to use WebDav.

  Read the article

• How to set up my network/bridging using Apple Airport equipment?

  - by John

  I'd like to set up my network like this, and I want to make sure it's possible using the hardware I have. I think it should be... I've got my cable modem in one room. I want to plug it into an Apple Airport Express and create my wireless my wireless network here. The airport express will do the NAT and DHCP. By my TV there are a few things to be networked (Xbox and Tivo). I have an airport extreme here. I'd like to have the airport extreme join the wireless network and share the connection to the ethernet ports. Can anyone provide some assistance on the best way to configure to do this? Thanks!

  Read the article

• Looking for a router-like web interface for my Debian gateway.

  - by marcusw

  Hey, I need a web interface program for my debian gateway which has the features of a router's one. Specifically, I must be able to easily Forward ports to various clients on the LAN or the router itself (it's also a server) Manage a DHCP server preferably including DHCP reservation for certain MACs Give me a list of the connected DHCP clients (optionally) Show which clients are the most active as far as bandwidth (something like iftop) Alternatively, it could be a graphical app which I could tunnel over ssh. No command line programs please...I'm used to doing this stuff with a point-and-click interface. Not adverse to command-line setup; just need to be able to reconfigure things graphically. Have a working LAMP setup. I've tried webmin, but it didn't satisfy the "easy" part...too many clicks and too many meny options.

  Read the article

• HP Media Smart remote access

  - by Coov

  I just purchased this box for home backups for my pc's and mac's. Everything works great accept for the remote access part. I can RD into the machine locally but I can't get to it from outside of my network. I've enabled port forwarding on my router but it doesn't seem to matter. I checked with Qwest and they don't block these ports so I'm at a loss. I do have Vonage in front of my router but I've taken it out and it didn't make a difference. I suspect I've made an error with my router setup. I'm a programmer and I'm playing in the world of the unknown here. I'm lost. Any suggestions?

  Read the article

• Using a second wifi router as a wireless bridge

  - by Greg-J

  I purchased a D-Link DGL-4500 to replace my aging WRT54G around a year ago, only to find it nowhere near as reliable. It's been collecting dust since. I'm wondering if there is a way to use it as a wireless bridge so I can connect it to my home network and then use it's ethernet ports to provide network access to several devices. Is this something that can be done? If not, are there devices meant for this? Any help would be appreciated.

  Read the article

• Want 2 external monitors with a 13' MacBook - is this possible?

  - by kevinburke

  I've got a 13' white MacBook from 2008 and I'd like to run one or two external monitors, my budget is $500. I've tried to do research and this is what I was going to get - will these work OK? Two Diamond BVU195 HD USB Display Adapters (DVI and VGA with included DVI to VGA adapter) to plug into the USB port Two Dell ST2310 monitors One external USB hub so I don't use up both of my USB ports Will this work? I've read some people say it does and some people say it doesn't, but I don't know enough to say either way. Also do you have recommendations for a better monitor than the dell sd2310? what's the best setup I can buy for $500? Thanks very much for your help, Kevin

  Read the article

• Why is the network speed on my Mac Pro (early 2009) so slow?

  - by Rafael

  I have a really weird networking issue on my Mac Pro (Early 2009). I can’t get higher network speeds than about 2MBit/s. It doesn’t matter if this is over AirPort or one of the Ethernet ports. An iMac and a Mac mini in the same network with almost the same configuration get about 25-30 MBit/s. I’ve read a couple of things about this on the official Apple forums, but there is no helpful information. Anyone else with Mac Pro network speed issues and who knows how to solve them?

  Read the article

• connect to paltalk server using a proxy

  - by Navid

  Hi I want to use paltalk, which is a kind of chat software, but the ports that this applications uses are closed in my country. What I need to do is to use a proxy server. Unfortunately the software itself does not provide a proxy setting. I though it would be possible to run paltalk on an O.S. installed on a virtual machine (say virtualbox) and configure the network setting of virtual machine to direct all its traffic through a proxy on host Operating system, but I could not find a way to do so neither. can anyone please help me?

  Read the article

• Network with bridge and port forwarding?

  - by rafek

  Hi! Below is my current (and planned) home network configuration. I would like to connect my non-wifi-capable desktop to my home network. The question is: HOW? What device do I need? The primary requiremen is that I need to be able to forward ports to my desktop. How would I achieve this? Is there something like "double port forwarding"? Could anyone please explain this configuration to me? Thank you in advance!

  Read the article

• What is the easiest way to do a direct file transfer of an extremely large file over the Internet?

  - by Kenneth Cochran

  I would like to transfer a 20+ GB file to a friend. I would like it to: Be fast Ensure data integrity Not require opening ports in either end's firewall Be free Not broadcast the file's existence to everyone on the Internet I've looked a several technologies and nothing seems to fit: Gnutella, BitTorrent, et al. satisfies 1, 2 and 4 JetBytes... 1, 3, 4 and 5 Yahoo Messenger, AIM, etc. 3, 4 and 5 FTP, SFTP... 1?, 4 and 5 rsync... 1, 2, 4 and 5 For a file this size speed and data integrity are the most important. No one wants a 20 GB file to fail a MD5 check after spending two days downloading it. Is there anything that meets all these requirements?

  Read the article

• Is SATA bandwith per Port or per Controller?

  - by instanceofTom

  I always assumed that it was per Controller channel, and that If I have 4xSATA 3.0Gb/s ports on my Motherboard then I should have a potential 12.0Gb/s of bandwith. However, after doing some searching I found conflicting information suggesting that if I had 4xSATA drives connected to my MB and were using them simultaneously each drive would get only 3.0Gb/s /4 = 768 Mb/s max bandwith. So I wanted to clear up my understanding. Side question: Are there other hdd/ssd bandwith bottlenecks to be aware of? (Links to already answered questions are more than welcome)

  Read the article

• IPtables Traffic Quota - up and down

  - by Nick

  I've been trying to set up traffic quotas for users on a shared server and i believe [with my limited knowledge] that iptables --quota and ports which have been selected for each user [--dport] is the way to do this... iptables -A OUTPUT --dport 1,2,3,4... --quota 123412341234 -j ACCEPT iptables -A OUTPUT --dport 1,2,3,4... -j DROP I think something like this would work to limit the traffic [and reset every month] but its only for traffic going out. Is there something I could do to combine -A OUTPUT and -A INPUT into one quota? Or, is there a different method I could use to achieve the same thing more efficiently? OS is debian squeeze Thanks.

  Read the article

• Is this a valid backup strategy for MongoDB?

  - by James Simpson

  I've got a single dedicated server with a MongoDB database of around 10GB. I need to do daily backups, but I can't have downtime with the database. Is it possible to use a replica set on a single disk (with 2 instances of mongod running on different ports), and simply take the secondary one offline and backup the data files to an offsite storage such as S3 (journaling is turned on)? Or would using master/slave be better than a replica set? Is this viable, and if so, what potential problems could I have? If not, how do I conceptualize this to work?

  Read the article

• Trouble opening my router to my web server

  - by Justin Heather Barrios

  Here's the story. I have a webs server created and connected to my router. The website works great when I'm connected to the router, but when I'm off the network I can't access the website. I got the IP for my router by googling "what is my ip." I have opened ports 80 to 10080 to link to the server in the router. One odd thing that I don't understand. When I am in network if I access XXX.XXX.XX.XX:80 I can access the web page no problem. If I access XXX.XXX.XX.XX:81 (or any other port) I get the error "Cannot access server." Any idea what the problem could be? Could it be my ISP?

  Read the article

• How to charge an iPhone on a Windows PC without Installaing iTunes

  - by Martin Hollingsworth

  I want to be able to charge my iPhone on my work computer, which is running Windows Server 2008 SP1 64-Bit. When I plug the iPhone in with the USB cable, it will not charge. Windows attempts to locate a driver for the device but only comes up with a generic Camera device and even if I allow that to be installed, the iPhone still does not charge. I have checked the computer's BIOS settings and did not find anything relating to power on the USB devices. I also tried this on ports at the back of the computer in addition to those on the front. The PC is a Dell Optiplex 780. As far as I can tell USB devices do not charge unless Windows has installed an appropriate driver. Since it is a work computer I do not want to install iTunes which does include a driver. I have a workaround that I will post as an answer for reference.

  Read the article

• Wordpress 3 mutli site install

  - by mike

  Hello, Trying to figure out if this is possible... My company has a cms product that was written in Java and we decided to use Wordpress to run blogs for our clients. Obviously, Wordpress does not run on tomcat(at least not by default) so we installed Pound(http://www.apsis.ch/pound/) on our server and have setup any Apache and Tomcat on different ports. When "/blog/" is requested, the request is directed to Apache. This works fine but we would like to use Wordpress multi site so that we can manage all the blogs from a single interface. We would also like the url for every site to be "/blog/" example: http://www.site1.com/blog/ http://www.site2.com/blog/ I'm thinking it would have to be done with apache??? Is it even possible? Thanks!

  Read the article

• How to "restart/repair" an USB port?

  - by Click Ok

  My laptop have 2 usb ports, but one is broken, so I use an USB hub in the another good USB port. In that USB hub, I use a mouse and keyboard. Suddenly, that USB port doesn't detects the mouse and keyboard (even with the light of the hub is on), and the only solution that I found is restarting the laptop. But just some minutes and the keyboard and mouse goes undetected again... So, I wonder if there is some method/software/etc to "restart/repair" the USB port without restart the PC. Thanks for all!

  Read the article

• HTTP, HTTPS and FTP is not working but SMTP and IMAP are working.

  - by nWorx

  Yesterday on a computer of a friend a strange thing happened. after booting the ports fo http, https and ftp are closed but e-mail is still working. in the control panel the windows firewall seems active even if he tries to deactivate it. I have a suspision that it is the faul of norton internet security 2010, we have tried to uninstall it, but the uninstallation did not work. when using the removal tool from symantec it just goes to 23% and then it crashes. the process ccSvcHst.exe is still running. How can I safely remove the rest of Norton Internet Security? Edit: Norton Internet Security 2010 is sucesfully removed, but still no connectivity...

  Read the article

• how do you uninstall an xampp installation that refuses to uninstall?

  - by Rick

  I downloaded xampp 1.7.3 (32) on windows 7 (64) in the programs(86) folder. both MySql and Apache refuse to run, they start and then instantly turn of. All ports are free. So I decide to uninstall however, when i run the uninstaller I receive the following error "Input Error: Can not find script file "C:\Program Files (x86)\xampp\uninst.temp\xampp_uninstall.vbs" XAMPP uninstall not OK Why is there spaces in the above line and does this matter "C:\Program Files (x86)" ? Can somebody please help me to understand the problem & uninstall xampp (or get it to work). It does not show in the control panel so I am stuck. All help is greatly appreciated. Thank you.

  Read the article

• unable to connect to remote sql server from SHDSL router

  - by user529265

  Got a new leased line network to our office that came with a SHDSL router (Watson). Currently, we are unable to use Sql Server management studio to connect to remote Sql databases. It errors out saying A connection was successfully established with the server, but then an error occurred during the pre-login handshake. (provider: TCP Provider, error: 0 - The specified network name is no longer available.) (Microsoft SQL Server, Error: 64) I logged into the Watson management panel and unblocked all the ports for TCP traffic (specified the range as 0 to 60000 and UDP as well - this include 1443 required for connecting to SQL Server). The router is the only thing that has changed. We are able to connect to it from other networks just fine. Is there something we are missing here. Any help would be greatly appreciated.

  Read the article

< Previous Page | 60 61 62 63 64 65 66 67 68 69 70 71  | Next Page >