Search Results

Search found 5727 results on 230 pages for 'routed commands'.

Page 64/230 | < Previous Page | 60 61 62 63 64 65 66 67 68 69 70 71  | Next Page >

• How to automatically restart RRAS service after OpenVPN

  - by JT

  I have OpenVPN set up on a Windows Server 2003 box using a routed configuration. This allows users to connect and access the work LAN subnet. There are remote hosts/services however that are only accessible when used via the work network. To enable access these, I push routes out to the clients to make sure traffic to these destinations goes across the VPN, and NAT the traffic using RRAS. This all works, except: if I restart the OpenVPN service, network traffic stops working until I restart the RRAS service as well. Is there a good way for me to make the RRAS service start/restart after OpenVPN? Are service dependencies the way to go? Obviously I could write a batch file to do this, but I'd like to make the process as bullet-proof and obvious as I can so it doesn't cause problems for other admins.

  Read the article

• Dual WAN port on a WRT54GL

  - by pufferfish

  Is it possible to reconfigure one of the LAN ports on a WRT54GL (running Tomato firmware) to act as a second WAN port? I have the following networks: PPOE connection to ADSL modem (works fine on the normal WAN port) WiFi neighbourhood network (in 178.X.X.X range), via a Mikrotik routerboard which I'd like to put on the WAN side of the router. I'd then like to set up routing so than some traffic (172.X.X.X) is routed to the Mikrotik and the rest to the ADSL modem. p.s. for practical reasons, I can't use the Mikrotik as the firewall/router. Edit: It seems this can be done by editing iptables, can someone tell me exactly how?

  Read the article

• How to send local mail via postfix to another server

  - by scotts

  I have postfix set up for use as an STMP server to send mail for my domain, but I receive email for the domain via gmail/google apps. The reason I use my own postfix is because I send out a lot of transactional emails to my customers using a web app, and the volume would exceed what google allows with its SMTP servers. Everything works fine, except cron & system mail gets routed to local users on the server, not to the appropriate accounts at google mail. How can I route this system mail to the respective google mail accounts instead?

  Read the article

• Communication between state machines with hidden transitions

  - by slartibartfast

  The question emerged for me in embedded programming but I think it can be applied to quite a number of general networking situations e.g. when a communication partner fails. Assume we have an application logic (a program) running on a computer and a gadget connected to that computer via e.g. a serial interface like RS232. The gadget has a red/green/blue LED and a button which disables the LED. The LEDs color can be driven by software commands over the serial interface and the state (red/green/blue/off) is read back and causes a reaction in the application logic. Asynchronous behaviour of the application logic with regard to the LED color down to a certain delay (depending on the execution cycle of the application) is tolerated. What we essentially have is a resource (the LED) which can not be reserved and handled atomically by software because the (organic) user can at any time press the button to interfere/break the software attempt to switch the LED color. Stripping this example from its physical outfit I dare to say that we have two communicating state machines A (application logic) and G (gadget) where G executes state changes unbeknownst to A (and also the other way round, but this is not significant in our example) and only A can be modified at a reasonable price. A needs to see the reaction and state of G in one piece of information which may be (slightly) outdated but not inconsistent with respect to the short time window when this information was generated on the side of G. What I am looking for is a concise method to handle such a situation in embedded software (i.e. no layer/framework like CORBA etc. available). A programming technique which is able to map the complete behaviour of both participants on classical interfaces of a classical programming language (C in this case). To complicate matters (or rather, to generalize), a simple high frequency communication cycle of A to G and back (IOW: A is rapidly polling G) is out of focus because of technical restrictions (delay of serial com, A not always active, etc.). What I currently see as a general solution is: the application logic A as one thread of execution an adapter object (proxy) PG (presenting G inside the computer), together with the serial driver as another thread a communication object between the two (A and PG) which is transactionally safe to exchange The two execution contexts (threads) on the computer may be multi-core or just interrupt driven or tasks in an RTOS. The com object contains the following data: suspected state (written by A): effectively a member of the power set of states in G (in our case: red, green, blue, off, red_or_green, red_or_blue, red_or_off...etc.) command data (written by A): test_if_off, switch_to_red, switch_to_green, switch_to_blue operation status (written by PG): operation_pending, success, wrong_state, link_broken new state (written by PG): red, green, blue, off The idea of the com object is that A writes whichever (set of) state it thinks G is in, together with a command. (Example: suspected state="red_or_green", command: "switch_to_blue") Notice that the commands issued by A will not work if the user has switched off the LED and A needs to know this. PG will pick up such a com object and try to send the command to G, receive its answer (or a timeout) and set the operation status and new state accordingly. A will take back the oject once it is no longer at operation_pending and can react to the outcome. The com object could be separated of course (into two objects, one for each direction) but I think it is convenient in nearly all instances to have the command close to the result. I would like to have major flaws pointed out or hear an entirely different view on such a situation.

  Read the article

• Best Practices - Core allocation

  - by jsavit

  This post is one of a series of "best practices" notes for Oracle VM Server for SPARC (also called Logical Domains) Introduction SPARC T-series servers currently have up to 4 CPU sockets, each of which has up to 8 or (on SPARC T3) 16 CPU cores, while each CPU core has 8 threads, for a maximum of 512 dispatchable CPUs. The defining feature of Oracle VM Server for SPARC is that each domain is assigned CPU threads or cores for its exclusive use. This avoids the overhead of software-based time-slicing and emulation (or binary rewriting) of system state-changing privileged instructions used in traditional hypervisors. To create a domain, administrators specify either the number of CPU threads or cores that the domain will own, as well as its memory and I/O resources. When CPU resources are assigned at the individual thread level, the logical domains constraint manager attempts to assign threads from the same cores to a domain, and avoid "split core" situations where the same CPU core is used by multiple domains. Sometimes this is unavoidable, especially when domains are allocated and deallocated CPUs in small increments. Why split cores can matter Split core allocations can silenty reduce performance because multiple domains with different address spaces and memory contents are sharing the core's Level 1 cache (L1$). This is called false cache sharing since even identical memory addresses from different domains must point to different locations in RAM. The effect of this is increased contention for the cache, and higher memory latency for each domain using that core. The degree of performance impact can be widely variable. For applications with very small memory working sets, and with I/O bound or low-CPU utilization workloads, it may not matter at all: all machines wait for work at the same speed. If the domains have substantial workloads, or are critical to performance then this can have an important impact: This blog entry was inspired by a customer issue in which one CPU core was split among 3 domains, one of which was the control and service domain. The reported problem was increased I/O latency in guest domains, but the root cause might be higher latency servicing the I/O requests due to the control domain being slowed down. What to do about it Split core situations are easily avoided. In most cases the logical domain constraint manager will avoid it without any administrative action, but it can be entirely prevented by doing one of the several actions: Assign virtual CPUs in multiples of 8 - the number of threads per core. For example: ldm set-vcpu 8 mydomain or ldm add-vcpu 24 mydomain. Each domain will then be allocated on a core boundary. Use the whole core constraint when assigning CPU resources. This allocates CPUs in increments of entire cores instead of virtual CPU threads. The equivalent of the above commands would be ldm set-core 1 mydomain or ldm add-core 3 mydomain. Older syntax does the same thing by adding the -c flag to the add-vcpu, rm-vcpu and set-vcpu commands, but the new syntax is recommended. When whole core allocation is used an attempt to add cores to a domain fails if there aren't enough completely empty cores to satisfy the request. See https://blogs.oracle.com/sharakan/entry/oracle_vm_server_for_sparc4 for an excellent article on this topic by Eric Sharakan. Don't obsess: - if the workloads have minimal CPU requirements and don't need anywhere near a full CPU core, then don't worry about it. If you have low utilization workloads being consolidated from older machines onto a current T-series, then there's no need to worry about this or to assign an entire core to domains that will never use that much capacity. In any case, make sure the most important domains have their own CPU cores, in particular the control domain and any I/O or service domain, and of course any important guests. Summary Split core CPU allocation to domains can potentially have an impact on performance, but the logical domains manager tends to prevent this situation, and it can be completely and simply avoided by allocating virtual CPUs on core boundaries.

  Read the article

• Internet connection very slow after Linksys configuration

  - by NLV

  Hello We have this network setup Server1 - DHCP server, Domain Controller, AD Lease line for Internet connection From lease line to Linksys router (we dont use wireless though) From linksys to Netgear (24 port Switch) and vonage (VoIP) Netgear to all our machines We configured Linsys with the static IP and DNS server addresses our ISP gave and we have routed it correctly. All our work machines are configured with Get IP automatically DNS server addresses our ISP gave The problem is that none of the sites are getting opened promptly. It is taking around 5 minutes to load google.com. But we are able to ping all the sites. What could be the problem?

  Read the article

• Oracle Enterprise Manager Extensibility News - June 2014

  - by Joe Diemer

  Introducing Extensibility Exchange Version 2 On the heals of Enterprise Manager 12c Release 4 this week comes version 2.0 of the Extensibility Exchange.  A new theme allows optimal viewing on a number of different computing devices from large monitor displays to tablets to smartphones.   One of the first things you'll notice is a scrollable banner with the latest news related to Enterprise Manager and extensibility.  Along with the "slider" and the latest entries from Oracle and the Partner community, new features like a tag cloud and an auto-complete search box provide a better way to find the plug-in, connector or other Enterprise Manager entity you are looking for.  Once you find it, a content details page with specific info related to that particular entity will enable you to access it at the provider's site and also rate and comment on that particular item. You can also send an email from the content details page which is routed to the developer.   And if you want to use version 1 of the Extensibility Exchange instead, you will be able to do so via the "Classic" option.  Check it out today at http://www.oracle.com/goto/emextensibility. Recent Additions from Oracle's Partner Community A number of important 3rd party plug-ins have been contributed by Oracle's partner community, which can be accessed via the Extensibility Exchange or by clicking the links in this blog: Dell Open Manage Fusion I-O ION Accelerator NetApp SANtricity E-Series PostgreSQL by Blue Medora You can also check out the following best practices and labs available via the Exchange: Riverbed Stingray Traffic Manager Reference Architecture Datavail Alert Optimizer Custom Templates Apps Associates' Oracle Enterprise Manager "Test Drives" for Oracle Database 12c Management Oracle Enterprise Manager Monitoring Essentials Oracle Application Management Suite for Oracle E-Business Suite

  Read the article

• How to selectively route network traffic through VPN on Mac OS X Leopard?

  - by newtonapple

  I don't want to send all my network traffic down to VPN when I'm connected to my company's network (via VPN) from home. For example, when I'm working from home, I would like to be able to backup my all files to the Time Capsule at home and still be able to access the company's internal network. I'm using Leopard's built-in VPN client. I've tried unchecking "Send all traffic over VPN connection." If I do that I will lose access to my company's internal websites be it via curl or the web browser (though internal IPs are still reachable). It'd be ideal if I can selectively choose a set of IPs or domains to be routed through VPN and keep the rest on my own network. Is this achievable with Leopard's built-in VPN client? If you have any software recommendations, I'd like to hear them as well.

  Read the article

• IIS exclude specific host?

  - by chakrit

  I have an IIS server running several websites. It is stationed behind an ISA server of which I do not have access. But I do have all of the defined websites (on port 80) routed to my server. So I want to take down one website, say it's foo.bar.com and in its place setup a LAMP server instead using a VM software. It needs to run alongside all the existing websites and it should not interfere with them. I have full control over my server, but not the ISA. Is this possible? If so, how? The OS is Win Server 2003 Standard with IIS6

  Read the article

• Always use one slow connection in preference of a "faster" one

  - by billc.cn

  In Windows, there's this automatic metric thing where the metric is selected according to the declared speed of the link. I now have a gigabit LAN routed to a 2MB DSL service and a HSDPA mobile broadband connection. The former is always chosen for Internet packets even though the latter is actually faster. I tried setting the mobile broadband's interface metric to 1 and raising its priority in the advanced settings of the adapter settings, but this does not seem to affect the metric of the default route. The default route to the Ethernet interface always have a lower metric than the mobile broadband interface. Am I missing something here?

  Read the article

• Trying to test Domain Collapsing / Consoldiation validity for SEO purposes

  - by Roy Rico

  At work, we're trying to determine the effectiveness of domain collapsing for SEO purposes. Our current structure is to have multiple web apps served from different servers, such as PUBLIC URLS - directly accessed by users www1.somecompany.com/webapp1 www2.somecompany.com/webapp2 www3.somecompany.com/webapp3 I'm proposing to put an Apache proxy in front of these applications that will mask the different domains and route the requests to proper server PUBLIC URL--------routed/forwarded to-----PRIVATE URL www.somecompany.com/webapp1 <-----> www1.somecompany.com/webapp1 www.somecompany.com/webapp2 <-----> www2.somecompany.com/webapp2 www.somecompany.com/webapp3 <-----> www3.somecompany.com/webapp3 In terms of SEO/page rank value, does this help?

  Read the article

• Isn't NAT a MUST when a LAN uses rfc 1918 private IPs?

  - by aks

  Isn't NAT a MUST when a LAN uses rfc 1918 private IPs? Can an organization assign its hosts with private IPs and still communicate with the external world without NAT? how can an internal host with a private IP (say 10.1.1.1) communicate with external world without NAT? I mean, how can the reply/response packet from the external world reach the original source as the packet with Dest IP = 10.1.1.1 will get lost as it can not be routed as many organizations can use the same IP. Why doesn't rfc 1918 (Address Allocation for Private Internets) make any mention of NAT?

  Read the article

• faking NAT with a VMware distributed switch across multiple hosts

  - by romant

  I need to construct a NAT for certain machines within the network. Wish to do this with dvSwitch - as it seems the logical way of attacking the problem as in this scenario there's just under 30 hosts. In order for the NAT'ed VM's to have access to the 'real' network. I am providing a 'router' VM, which will have access to the WAN/outside network, and also act as the DHCP server for the NAT'ed machines. Problem Space When the machines connected to the NAT interface and the router are on the same host, then they get an IP from the router VM, and work perfectly (routed outside). Unfortunately machines on other Hosts that are connected to the dvSwitch do not get an IP and further tcpdump shows no network data getting through across the hosts within the dvSwitch. Has anyone achieved a NAT solution using a dvSwitch before that they could share?! Thank you. EDIT: Including the diagram.

  Read the article

• Making internal website available publicly (Win 2008 Server)

  - by endigo

  I have an IIS 7 web site that is running on a Windows 2008 Server (64-bit) VMWare on a Windows 2008 Server (64-bit) Host on my local network. My router is a Firebox XEdge and it has port 80 directed to the IP of the server on VMWare. I can reach the web site from inside the network, but I cannot reach the site from outside the network. I have other web sites that are working through the Firebox, and I am confident that it is configured correctly. I suspect that Windows 2008 server is blocking routed or public addresses, but I have shut down the firewall on the Server that is running on VMWare and the AVG Anti-virus to no avail. How can I make my site available publicly.

  Read the article

• Linksys router with multiple external IP's

  - by Adrian Mester

  In an office I've got a network connection with 5 external IPs and a Linksys router (I'm not 100% percent sure of the model). I need 4 of those 5 IPs to be routed to a server, and the fifth to be shared between the other computers at the office. This can probably be done using a switch in front of the router. Connect the server and the router to the switch, and let the router handle the rest of the network. Is there a way to configure the router to route the 4 IPs to the server, and create an internal network the the other computers at the same time?

  Read the article

• Webserver on a rotating server with NAT IP or changing IPs

  - by hpsoftware

  i would have to elaborate my questions so please have patience Explaining the logic. if you are familiar with logmein then it installs a client software on your computer then it kinda keeps tracks where you computer is as long as it's connected to internet. So you can always access your computer no matter where it is whatever it's IP is you just go to logmein.com and then you can just access it. Now what i am asking 1. Let's assume i have a website hosted on my laptop let's call it webserver. so then i move around i have a new IP sometime even on a hotel network is it possible to do something like what logmein does so i can keep moving around my Webserver to new IP but it has some local client or something which keeps updating my IP or something i am sure i would need a gateway server somewhere which is connected to my domain name via DNS so somebody accessing my website www.mywebsite.com goes to my main server then gets routed to my laptop which could be anywhere but my gateway server is able to communicate to my webserver I will keep updating the case description based on comments to make more sense. please have patience with me. Regards

  Read the article

• Load Balancing a UDP server

  - by Hellfrost

  Hello StackOverflow, I have a udp server, it is a central part in my business process. in order to handle the loads I'm expecting in the production environment I'll probably need 2 or 3 instances of the server. The server is almost entirely stateless, it mostly collects data, and the layer above it knows how to handle the minimal amount of stale data that can arise from the the multiple server instances. My question is, how can I implement load balancing between the servers? I would prefer to distribute the requests as evenly as possible between the servers. I would also would like to have some fidelity, I mean if client X was routed to server y, then I want all of X's subsequent requests to go to server Y, as long as it is sensible and not overloads Y. By the way it is a .NET system... what would you recommend?

  Read the article

• Dual-WAN router

  - by aix

  I am looking for a router that would fit the following requirements: Two WAN interfaces: the primary is PPPoE, the secondary will link to a GigE port on another router (a 100Mbps link will suffice); Two (ideally four) GigE LAN ports; No requirement for a firewall; No requirement for Wi-Fi; Inexpensive. The plan for the two WAN interfaces is as follows. All outbound traffic will go to the primary, with exceptions based on destination IP/subnet or possibly on src+dest IPs/subnets. Such exceptions should be routed to the secondary. It would be very nice if, should the primary go down, the secondary would automatically take over for all outbound traffic. I am reasonably sure that I can put something together based on dd-wrt. However, I'd like to hear from you what alternatives are out there (especially something easier to set up for my use case, even if it means paying more for the hardware.)

  Read the article

• Virtualhost Wildcard Subdomains

  - by Khuram

  We have one static IP on which we have routed our company website. We have setup a local machine on windows with WAMP to run our testing server. We want virtual hosts to test our different apps. However, when creating subdomains, we have a new project which uses wildcard subdomains. How can we create the wildcard subdomains in VirtualHosts. We use, NameVirtualHost * <VirtualHost *> ServerAdmin admin@test DocumentRoot "E:/Wamp/www/corporate" ServerName companysite.com </VirtualHost> <VirtualHost *> ServerAdmin admin@test DocumentRoot "E:/Wamp/www/project" ServerName project.companysite.com </VirtualHost> <VirtualHost *> ServerAdmin admin@test DocumentRoot "E:/Wamp/www/project" ServerName *.project.companysite.com </VirtualHost> However, the last * wildcard does not work. Any help?

  Read the article

• Windows Server 2003/Exchange 2007: How to setup public domain mail.foo.com to route to internal exch

  - by ryan.keeter

  Good day, I have an internal Exchange Server 2007 and a Windows Server 2003 domain. At this point in time I have an external DNS setup (DynDNS 29.95 service) to resolve foo.com to my singular public IP address then it gets routed to external facing site. I would like to know how to setup POP on mail.foo.com and SMTP on smtp.foo.com, and more importantly, what needs to be setup in Exchange server to allow for this to happen. My end state is to send email through smtp.foo.com and receive mail on mail.foo.com. As of now, when I create a user within Exchange the default email address is [email protected], and I would like it to be [email protected]. Thank you and I appreciate the help as I am a .NET developer trying to do sys admin work, and it is MUCH harder than I have ever imagined, my hat is off to all sys admins and IT pros.

  Read the article

• Configure Postfix to use external MX servers for delivery of local mail if user is unknown

  - by mr.b

  I have a following setup: linux box with postfix configured to be responsible for example.com domain domain's MX servers are configured so that mail sent to example.com is sent to google mail servers several user accounts on linux machine exist (same machine also hosts example.com site) When someone from the outside attempts to send mail to address ending with @example.com, it gets routed to google mail (and there handled appropriately). When linux machine tries to send mail to outside world, mail is delivered correctly, as reverse dns and spf records are configured correctly, so linux machine is valid mail sender for example.com domain (along with google mail servers). However, here's the problem. When php application (hosted at linux box) tries to send mail to [email protected] (and someuser doesn't exist on linux box), it fails, since it doesn't even consult google mail servers, but postfix smtp locally concludes that "someuser" is unknown. So, the question is: how do I tell postfix to relay mails sent to @example.com domain to google mail servers (so, to servers specified in MX records), IF and only if a mailbox is not found locally.

  Read the article

• How can I use a computer as a router and send all client traffic through anonymous proxies?

  - by Terrapin

  Is there a way that I can setup a spare box as a router on my network, and route client traffic through a proxy in order to hide my location? Specifically, I would like internet traffic to/from my Roku Box to be routed via proxy, but there is no proxy support built in to the Roku. So I would like wire my Roku directly my computer's second NIC, and force all traffic through a proxy. What kind of software and hardware setup will I need? Also, which anonymous proxy service are best for this purpose? I'm not interesting in full anonymity or encryption. I simply want to mask my location while providing the best possible throughput.

  Read the article

• why do Vagrant docs suggest using public IP address 33.33.33.10 for local VMs?

  - by Gert

  I'm following a tutorial to set up vagrant (a tool to build and configure portable virtual machine images), and it seems that vagrant documentation suggests using IPv4 address 33.33.33.10 to configure a new box. That is a publicly routed IP adress, so I'm a bit confused why using this address is suggested. Since I don't own this network, I should not use an address from the 33.33.33.10/8 range. Am I correct in thinking that I should only use either a public address from a network I own, or an address from one of the private ranges as defined in RFC 1918? If so, why does Vagrant documentation suggest otherwise?

  Read the article

• Teminal non-responsive on load, can't enter anything until CTRL+C

  - by Silver Light

  Hello! I have an issue with terminal in Ubuntu 10.04. When I launch it, it hangs, like this: I cannot do anything until I press CTRL+C: I cannot remember when this started. What can be wrong? Looks like teminal is loading or processing something each time it loads. How can I diagnose and solve this problem? EDIT: Here are the conents of ~/.bashrc: # ~/.bashrc: executed by bash(1) for non-login shells. # see /usr/share/doc/bash/examples/startup-files (in the package bash-doc) # for examples # If not running interactively, don't do anything [ -z "$PS1" ] && return # don't put duplicate lines in the history. See bash(1) for more options # ... or force ignoredups and ignorespace HISTCONTROL=ignoredups:ignorespace # append to the history file, don't overwrite it shopt -s histappend # for setting history length see HISTSIZE and HISTFILESIZE in bash(1) HISTSIZE=1000 HISTFILESIZE=2000 # check the window size after each command and, if necessary, # update the values of LINES and COLUMNS. shopt -s checkwinsize # make less more friendly for non-text input files, see lesspipe(1) [ -x /usr/bin/lesspipe ] && eval "$(SHELL=/bin/sh lesspipe)" # set variable identifying the chroot you work in (used in the prompt below) if [ -z "$debian_chroot" ] && [ -r /etc/debian_chroot ]; then debian_chroot=$(cat /etc/debian_chroot) fi # set a fancy prompt (non-color, unless we know we "want" color) case "$TERM" in xterm-color) color_prompt=yes;; esac # uncomment for a colored prompt, if the terminal has the capability; turned # off by default to not distract the user: the focus in a terminal window # should be on the output of commands, not on the prompt #force_color_prompt=yes if [ -n "$force_color_prompt" ]; then if [ -x /usr/bin/tput ] && tput setaf 1 >&/dev/null; then # We have color support; assume it's compliant with Ecma-48 # (ISO/IEC-6429). (Lack of such support is extremely rare, and such # a case would tend to support setf rather than setaf.) color_prompt=yes else color_prompt= fi fi if [ "$color_prompt" = yes ]; then PS1='${debian_chroot:+($debian_chroot)}\[\033[01;32m\]\u@\h\[\033[00m\]:\[\033[01;34m\]\w\[\033[00m\]\$ ' else PS1='${debian_chroot:+($debian_chroot)}\u@\h:\w\$ ' fi unset color_prompt force_color_prompt # If this is an xterm set the title to user@host:dir case "$TERM" in xterm*|rxvt*) PS1="\[\e]0;${debian_chroot:+($debian_chroot)}\u@\h: \w\a\]$PS1" ;; *) ;; esac # enable color support of ls and also add handy aliases if [ -x /usr/bin/dircolors ]; then test -r ~/.dircolors && eval "$(dircolors -b ~/.dircolors)" || eval "$(dircolors -b)" alias ls='ls --color=auto' #alias dir='dir --color=auto' #alias vdir='vdir --color=auto' alias grep='grep --color=auto' alias fgrep='fgrep --color=auto' alias egrep='egrep --color=auto' fi # some more ls aliases alias ll='ls -alF' alias la='ls -A' alias l='ls -CF' # Add an "alert" alias for long running commands. Use like so: # sleep 10; alert alias alert='notify-send --urgency=low -i "$([ $? = 0 ] && echo terminal || echo error)" "$(history|tail -n1|sed -e '\''s/^\s*[0-9]\+\s*//;s/[;&|]\s*alert$//'\'')"' # Alias definitions. # You may want to put all your additions into a separate file like # ~/.bash_aliases, instead of adding them here directly. # See /usr/share/doc/bash-doc/examples in the bash-doc package. if [ -f ~/.bash_aliases ]; then . ~/.bash_aliases fi # enable programmable completion features (you don't need to enable # this, if it's already enabled in /etc/bash.bashrc and /etc/profile # sources /etc/bash.bashrc). if [ -f /etc/bash_completion ] && ! shopt -oq posix; then . /etc/bash_completion fi # Source .profile if [ -f ~/.profile ]; then . ~/.profile fi Setting -x at the beginning showed me that it tries to repeat this without stopping: +++++++++++++++++++ '[' 'complete -f -X '\''!*.@(pdf|PDF)'\'' acroread gpdf xpdf' '!=' 'complete -f -X '\''!*.@(pdf|PDF)'\'' acroread gpdf xpdf' ']' +++++++++++++++++++ line='complete -f -X '\''!*.@(pdf|PDF)'\'' acroread gpdf xpdf' +++++++++++++++++++ line='complete -f -X '\''!*.@(pdf|PDF)'\'' acroread gpdf xpdf' +++++++++++++++++++ line=' acroread gpdf xpdf' +++++++++++++++++++ list=("${list[@]}" $line) +++++++++++++++++++ read line

  Read the article

• Running Powershell from within SharePoint

  - by Norgean

  Just because something is a daft idea, doesn't mean it can't be done. We sometimes need to do some housekeeping - like delete old files or list items or… yes, well, whatever you use Powershell for in a SharePoint world. Or it could be that your solution has "issues" for which you have Powershell solutions, but not the budget to transform into proper bug fixes. So you create a "how to" for the ITPro guys. Idea: What if we keep the scripts in a list, and have SharePoint execute the scripts on demand? An announcements list (because of the multiline body field). Warning! Let us be clear. This list needs to be locked down; if somebody creates a malicious script and you run it, I cannot help you. First; we need to figure out how to start Powershell scripts from C#. Hit teh interwebs and the Googlie, and you may find jpmik's post: http://www.codeproject.com/Articles/18229/How-to-run-PowerShell-scripts-from-C. (Or MS' official answer at http://msdn.microsoft.com/en-us/library/ee706563(v=vs.85).aspx) public string RunPowershell(string powershellText, SPWeb web, string param1, string param2) { // Powershell ~= RunspaceFactory - i.e. Create a powershell context var runspace = RunspaceFactory.CreateRunspace(); var resultString = new StringBuilder(); try { // load the SharePoint snapin - Note: you cannot do this in the script itself (i.e. add-pssnapin etc does not work) PSSnapInException snapInError; runspace.RunspaceConfiguration.AddPSSnapIn("Microsoft.SharePoint.PowerShell", out snapInError); runspace.Open(); // set a web variable. runspace.SessionStateProxy.SetVariable("webContext", web); // and some user defined parameters runspace.SessionStateProxy.SetVariable("param1", param1); runspace.SessionStateProxy.SetVariable("param2", param2); var pipeline = runspace.CreatePipeline(); pipeline.Commands.AddScript(powershellText); // add a "return" variable pipeline.Commands.Add("Out-String"); // execute! var results = pipeline.Invoke(); // convert the script result into a single string foreach (PSObject obj in results) { resultString.AppendLine(obj.ToString()); } } finally { // close the runspace runspace.Close(); } // consider logging the result. Or something. return resultString.ToString(); } Ok. We've written some code. Let us test it. var runner = new PowershellRunner(); runner.RunPowershellScript(@" $web = Get-SPWeb 'http://server/web' # or $webContext $web.Title = $param1 $web.Update() $web.Dispose() ", null, "New title", "not used"); Next step: Connect the code to the list, or more specifically, have the code execute on one (or several) list items. As there are more options than readers, I'll leave this as an exercise for the reader. Some alternatives: Create a ribbon button that calls RunPowershell with the body of the selected itemsAdd a layout pageSpecify list item from query string (possibly coupled with content editor webpart with html that links directly to this page with querystring)WebpartListing with an "execute" columnList with multiselect and an execute button Etc!Now that you have the code for executing powershell scripts, you can easily expand this into a timer job, which executes scripts at regular intervals. But if the previous solution was dangerous, this is even worse - the scripts will usually be run with one of the admin accounts, and can do pretty much anything...One more thing... Note that as this is running "consoleless" calls to Write-Host will fail. Two solutions; remove all output, or check if the script is run in a console-window or not.  if ($host.Name -eq "ConsoleHost") { Write-Host 'If I agreed with you we'd both be wrong' }

  Read the article

< Previous Page | 60 61 62 63 64 65 66 67 68 69 70 71  | Next Page >