Search Results

Search found 14588 results on 584 pages for 'usb drive'.

Page 64/584 | < Previous Page | 60 61 62 63 64 65 66 67 68 69 70 71  | Next Page >

• Low 'Burst Rate' from SATA drive in HDTune?

  - by UpTheCreek

  I recently upgraded my laptop's v slow hard drive to a seagate momentus 7200. Everything is working fine, but I'm a bit confused by these benchmark results: The burst rate is significantly less than the Maximim transfer rate, and not much higher than the normal minimum (if you ignore the spikes). What's going on here? On the HDtune website it defines Burst Rate as: ...the highest speed (in megabytes per second) at which data can be transferred from the drive interface (IDE or SCSI for example) to the operating system. Which begs some questions... e.g. if this is the highest, then how did the bechmarking tool record the 103MB/sec maximum? And if this really is the true maximum, then where is the bottleneck? The laptops SATA interface is on an Intel 82801GBM southbridge controller. When I check in hardware manager, I see that it's driver is iaStor.sys from 2005. Maybe that's the issue? I'll look for a newever version, but any insights would be appreciated. Thanks UPDATE: Acorting to this page on the HDTune website... An important parameter of the test is the Burst Rate. This value should always be higher than the maximum transfer rate. A lower value is usually an indication of a configuration problem. So what might be the configuration problem?

  Read the article

• Data recovery on working hard drive

  - by emgee

  So I have a 5 bay hot swap SATA enclosure that's connected to a Silicon Image-based SATA adapter in a computer. It's running XP Pro. There are two 1.5TB hard drives in slots 1 and 2 respectively, set up using RAID 1 using the the Silicon Image utility. There are also two 1TB drives in bays 3 and 4, also set to RAID 1 the same way. The partitions for both RAID arrays are Dynamic partitions. A few days back, there was a bare hard drive that needed some files copied off of, so it was popped it in bay 5, that bay to pass-through, and the copied data off of it. Later, I noticed that my 1.5TB drives no longer showed up in windows. In the Silicon Image utility, the drives showed up fine, no error. However, in Device Manager, it shows the RAID 1 array as uninitialized. It shows up as the right size, etc., but nothing else. There's no sign of anything wrong with either drive, so I'm not sure what happened exactly. I'm not the only one who has access to that computer, so it is possible there is something else done to it that I don't know of. There's quite a lot of data on it still, and if at all possible, I'd prefer to not send it to Ontrack. Does anyone know of software that would restore the partitions, keeping in mind that it's a Windows LDM partition? I have access to a variety of Operating Systems, so something that would work on Mac, Windows or Linux would be acceptable. The programs I usually use are not compatible with LDM.

  Read the article

• Adding SSD as boot drive to existing system

  - by thegrinner

  I recently bought two 128GB SSDs that I'm planning on adding (RAID 0) to a system I currently have on a 1TB HDD. I'm hoping to redo the disk space such that the SSDs act as the boot drive (only other items would be things I install there explicitly) while the majority of my system is on the HDD - documents, media, program files. Something like this: SSD = [ OS | Explicitly placed programs] HDD = [ Program Files | Media | Documents | etc] I have an external drive capable of holding all the data I want to save, so the backup isn't too much of a concern. What I'm worried about is how I should go about doing this - do I need to do a clean install on the SSDs, reformat the HDD, move things like Program Files/Users to the HDD, and then restore data (not full programs but things like saves)? Should I be using one of the regedit hacks I've seen around to change the default install directories instead of moving program files and users? Should I have the actual folders on the HDD and symlinks on the SSD? Or is there a better solution? Do I need to disconnect my HDD while doing the clean Windows install?

  Read the article

• osx HD as usb HD (to PC)

  - by Daniel

  Is it possible to hook up a mac to a pc via usb, and have direct access to the hard drive? Is there any software that could do this?

  Read the article

• linux: automount internal hard drive during boot?

  - by John Doe

  i try to create my own NAS and i need to automount the internal sata disks during boot i know i could do using fstab but im searching for a more easy/generalized way so its easier to scale with less handwork needed for every hard drive attached (or every mainboard added to the cluster) so anyone knows how to automount internal disks without using fstab like ubuntu does for usb drives? im using ubuntu server 9.10 thx all

  Read the article

• OS X HD as USB HD (to PC)

  - by Daniel

  Is it possible to hook up a Mac to a PC via USB, and have direct access to the hard drive? Is there any software that could do this?

  Read the article

• SATA Hard drive not detecting

  - by Srin

  I have a dead laptop, Trying to recover data from the Hard drive (Sata2) I tried putting the HD in one similar laptop , it's not recognized I got USB-SATA Adapter and plugged the HD , and still the HD is not recognized can you tell me is there any other possible way to get my data back ?

  Read the article

• wireless usb disk?

  - by Stefano Borini

  My dream is to have a "USB disk" I can access (wifi or bluetooth) without taking it out of my wallet. Does something like this exist?

  Read the article

• What's the difference between "Flash Drive" and "Flash Memory"?

  - by Clive D

  I have a problem with a Blu ray disk I bought. I talked to a Sony technician who advised me to plug a "USB Flash Memory Stick" into the Blu-ray player. Is this something specific? Is there a difference between the following two? "USB Flash Drive" "USB Flash Memory" When I go to Curry's or other sites that sell USB Sticks, they only talk about "USB Flash Drives". I've been in computing for many years and know the basics, but "memory" and "drive" are different things to me.

  Read the article

• Windows XP detecting printer as USB hub - how to start again without reinstalling XP?

  - by Umber Ferrule

  Fresh install of Windows XP SP3. No system restore. Didn't install USB printer drivers before connected it to PC. Mistakenly allowed XP to auto install some driver which turned out to be a USB hub(!). Now I can't get XP to see the printer as a printer. Have tried uninstalling the offending driver in Device Manager and rebooting but it keeps being detected as a USB hub. How do I revert XP back to a pristine, unsullied USB state so it doesn't know about the USB hub and will (hopefully) install the printer as a printer?

  Read the article

• Ubuntu - Automatically mount external drives to /media/LABEL on boot without a user logged in?

  - by endolith

  This question is similar, but kind of the opposite of what I want. I want external USB drives to be mounted automatically at boot, without anyone logged in, to locations like /media/<label>. I don't want to have to enter all the data into fstab, partially because it's tedious and annoying, but mostly because I can't predict what I'll be plugging into it or how the partitions will change in the future. I want the drives to be accessible to things like MPD, and available when I log in with SSH. gnome-mount seems to only mount things when you are locally logged into a Gnome graphical session.

  Read the article

• Why doesn't my Droid phone charge when connected to a powered USB hub that is not connected to my computer?

  - by pkaeding

  I notice that my new Motorola Droid phone charges perfectly fine when I connect it to my computer via the USB cable, or if I connect it to a car cigarette lighter-USB adapter, or a wall power-USB adapter. It also works fine when I connect it to a powered USB hub that is connected to my computer. However, if that same powered USB hub is not connected to my computer when I connect the phone, it does not charge. If I connect the computer to the hub, and then connect the phone to the hub, it will charge. If I then disconnect the computer from the hub, the phone will continue to charge. Does anyone know why this is happening, or what I can do to be able to charge my phone from a powered hub, without my computer being present?

  Read the article

• Prevent Windows 7 from unpluging External HDD

  - by marverix

  I have installed Windows 7 as my media server. I pluged in 500GB external HDD via USB. I have changed power plan to Best Performance and changed advenced power settings to never turn off HDD etc. I even yesterday wrote powershell script (create and delete folder on this disk) and I have added it to harmonogram to run every 5 minutes starting from system boot. And nothing! Disk after some time (I realy can't say when) is turning off and Windows show "Unknown Device" in Device Manager. Then only system reboot or disk reboot helps. Any ideas how to prevent Windows 7 from stopping my external HDD? Cheers!

  Read the article

• How can I run Ghost from a bootable USB key drive?

  - by Joe Philllips

  I have a laptop that does not have a cd-rom or floppy drive. It is able to boot from USB though. I have a disk image (ghost) of the disk that I need to restore back onto the laptop. I can't find a way to actually run the Ghost utility from a USB key though. I believe the ghost.exe should run from within DOS just fine but I can't seem to create a bootable USB key with DOS on it that allows me to run an EXE. Edit: I managed to find a Ghost utility that I could load from a bootable USB drive. Unfortunately, when I plug in my NTFS external drive (USB), it is not detected.

  Read the article

• Seeking a solution to automatically copy files from the cd-rom disk to the USB drive once it's connected.

  - by Ray Nathan

  I plan to distribute a free CD that automatically copies files to a connected usb device. This process will be done on the computers of the users that obtain the cd. The CD will contain an autorun.ini file that will instruct the computer to copy a set of files located on the cd..to a specific directory on the connected usb device. The usb drive letter is not the same on all the systems, therefore...Windows XP should automatically know the drive letter of the usb device before the copy operation begins. What would be the best way of creating a short batch file or script that I can place on the CD to execute this process? Also, please note that it is NOT feasible or recommended to include a batch file on the USB devices to sync this operation due to the explanation at the beginning of this paragraph. :) Thank You All

  Read the article

• Differentiate CD-Drive and Hard Disk-Drive in Java

  - by SamSol

  How to differentiate CD-Drive and Hard Disk-Drive in Java?

  Read the article

• WD Elements Desktop External - Not recognised on a single computer

  - by Aelexe

  My WD Elements Desktop External is no longer recognised on my main computer. It has worked fine in the past, but now all of a sudden is not detected. It does not prompt when plugged in, nor does it show up in the disc management interface or the device manager. It appears to be aware that it is plugged in however as the light on the external blinks rapidly for a short while after being plugged in. The strangest thing however is that it works fine on other computers, including my family computers and my laptop. I have attempted to troubleshoot the issue by trying various USB devices in multiple ports on each system to see if there is any correlation with the issue, but have come up with nothing that gives me an idea of what is going on. I have also attempted to format the external using my laptop, but that has not helped either. If anyone has had a similar issue, or knows of any potential solutions, please post your advice. Thanks for your time.

  Read the article

• Hooking up many different external HDs simultaneously

  - by cbizz

  I need a large amount of external storage for an upcoming project. I'm planning on purchasing 10 2TB external drives. I need them all hooked up to a single machine at the same time. What issues will I run into? I plan on using 2 power strips and having them all externally powered from the wall. I will use a USB hub to plug in all the drives. I need drive access time to be as fast as possible. I am using Ubuntu Linux(64 bit). Will I be able to mount 10 drives?

  Read the article

• While running a batch file in Windows 7 with Admin rights from a thumb drive, how can I get the file path back to the thumb drive?

  - by Jeremy DeStefano

  I have a piece of software that is being distributed to several departments for installation onto Windows 7 laptops. They install software from the thumb drive and then they have to run a script to properly configure the software. Because the script is changing registry files and program files, it requires Admin rights. When running as Admin, it drops into the System32 folder and I no longer have an easy scriptable way to access files that need to be copied from the thumb drive, simply because I don't know for sure what drive letter its going to use on the various machines. Previous installations were on Windows XP and the command window file path stayed within the script folder. I've found similar questions here and I have already tried Relative Paths, but it can't seem to find the proper folder on the thumb drive or I can't seem to find the proper way to format it.

  Read the article

• Platform Builder: Disable the USB Driver Dialog

  - by Bruce Eitman

  For a long time, Windows CE developers and users have wanted to disable the USB Driver Dialog that is displayed when an unknown USB device is plugged into the host controller.   Of course the question is always why would you want to do such a thing? The simple answer is that there are USB devices that are needed, like printers, which expose multiple functions to the bus, like scanners and faxes, which no Windows CE driver exists to support.   So the printer quietly loads a driver, but then the other functions cause a dialog to be shown. One solution is to create a USB Class driver that loads by default if no other driver has been loaded. This driver just accepts anything that it sees and then does nothing with it. Starting with the Windows Embedded CE 6.0 R3 March QFE/update, the USB 2.0 driver has a registry value to disable the dialog: [HKEY_LOCAL_MACHINE\Drivers\USB\LoadClients]       "DoNotPromptUser"=dword:0   Setting the DoNotPromptUser value to 1 disables the dialog. The default value is zero, so the driver continues to behave in the same way it always did unless you change this registry value.     Copyright © 2010 – Bruce Eitman All Rights Reserved

  Read the article

• Autodetect/mount SDCards and run script for them on Linux

  - by Brendan

  Hey Everyone, I'm currently running SME Server, and need to have a script run upon the attachment of SD Cards to my server. The script itself works fine (it copies the contents of the cards), but the automounting and execution of the script is where I'm having issues. The I have a USB hub consisting of 10 USB ports; that shows up as: [root@server ~]# lsusb Bus 004 Device 002: ID 0000:0000 Bus 004 Device 001: ID 0000:0000 Bus 003 Device 001: ID 0000:0000 Bus 002 Device 001: ID 0000:0000 Bus 001 Device 055: ID 1a40:0101 TERMINUS TECHNOLOGY INC. Bus 001 Device 051: ID 1a40:0101 TERMINUS TECHNOLOGY INC. Bus 001 Device 050: ID 1a40:0101 TERMINUS TECHNOLOGY INC. Bus 001 Device 001: ID 0000:0000 (The hub is the TERMINUS TECHNOLOGY INC entries) As I cannot plug SD Cards directly into the server; I use a USB to SD card attachement (10 of them) plugged into the hub to read the cards. Upon pluggig the 10 attachments (without cards) into the hub; lsusb yields the following: [root@server ~]# lsusb Bus 004 Device 002: ID 0000:0000 Bus 004 Device 001: ID 0000:0000 Bus 003 Device 001: ID 0000:0000 Bus 002 Device 001: ID 0000:0000 Bus 001 Device 073: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 072: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 071: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 070: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 069: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 068: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 067: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 066: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 065: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 064: ID 05e3:0723 Genesys Logic, Inc. Bus 001 Device 055: ID 1a40:0101 TERMINUS TECHNOLOGY INC. Bus 001 Device 051: ID 1a40:0101 TERMINUS TECHNOLOGY INC. Bus 001 Device 050: ID 1a40:0101 TERMINUS TECHNOLOGY INC. Bus 001 Device 001: ID 0000:0000 As you can see, the readers are the "Gensys Logic, Inc" entries. Plugging in an SD card to a reader doesn't affect lsusb (it reads exactly as above), however my system recognises the cards fine; as indicated by dmesg: Attached scsi generic sg11 at scsi54, channel 0, id 0, lun 0, type 0 USB Mass Storage device found at 73 SCSI device sdd: 31388672 512-byte hdwr sectors (16071 MB) sdd: Write Protect is on sdd: Mode Sense: 03 00 80 00 sdd: assuming drive cache: write through SCSI device sdd: 31388672 512-byte hdwr sectors (16071 MB) sdd: Write Protect is on sdd: Mode Sense: 03 00 80 00 sdd: assuming drive cache: write through sdd: sdd1 SCSI device sdd: 31388672 512-byte hdwr sectors (16071 MB) sdd: Write Protect is on sdd: Mode Sense: 03 00 80 00 sdd: assuming drive cache: write through SCSI device sdd: 31388672 512-byte hdwr sectors (16071 MB) sdd: Write Protect is on sdd: Mode Sense: 03 00 80 00 sdd: assuming drive cache: write through sdd: sdd1 SCSI device sdd: 31388672 512-byte hdwr sectors (16071 MB) sdd: Write Protect is on sdd: Mode Sense: 03 00 80 00 sdd: assuming drive cache: write through SCSI device sdd: 31388672 512-byte hdwr sectors (16071 MB) sdd: Write Protect is on sdd: Mode Sense: 03 00 80 00 sdd: assuming drive cache: write through sdd: sdd1 If I manually mount sdd1 (mount /dev/sdd1 /somedirectory/) this works fine. What I'm really after is a solution that automounts each of the cards as they are inputted into the reader; and executes a script for them (this will involve copying their contents to another directory). My problem is that I don't know how to do this; I don't think udev will work as the USB devices don't change; if I could somehow get udev working with /dev/disk/by-path/ however I think this is doable (it seems to keep constant entries). ls /dev/disk returns: pci-0000:00:1d.7-usb-0:4.1.1.1:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.1.1.2:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.1.1.3:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.1.1.4:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.1.2:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.1.3:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.1.4:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.2:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.3:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.4:1.0-scsi-0:0:0:0 pci-0000:00:1d.7-usb-0:4.4:1.0-scsi-0:0:0:0-part1 pci-0000:0b:01.0-scsi-0:0:1:0 pci-0000:0b:01.0-scsi-0:0:1:0-part1 pci-0000:0b:01.0-scsi-0:0:1:0-part2 From above, we can see I have only one card plugged into the reader (pci-0000:00:1d.7-usb-0:4.4:1.0-scsi-0:0:0:0-part1). Going mount /dev/disk/by-path/pci-0000\:00\:1d.7-usb-0\:4.4\:1.0-scsi-0\:0\:0\:0-part1 Works and places the card under /media/usbdisk/, however: mount /dev/disk/by-path/pci-0000\:00\:1d.7-usb-0\:4.4\:1.0-scsi-0\:0\:0\:0-part1 slot1/ doesn't work, and returns "mount: can't get address for /dev/disk/by-path/pci-0000" Any ideas and solutions would be great, I've seen the knowledge of a lot of the guys on here before so I'm hopeful someone can help me out. Thanks

  Read the article

• Infrared usb adapter not hot pluggable?

  - by A. Goossens

  For transferring exercise files from my Polar heart rate monitor i use the software Protrainer 5 with an external infrared usb adapter. Using Wine to run Protrainer 5 and some adjustments mentioned here (using irda-utils) i managed to make it work. Well, sort of: every time i want to transfer exercise files and the adapter is not plugged in i have to reboot my laptop with the usb adapter plugged in to make it work. Since i have a laptop it unfortunately is no option to just always leave the adapter in. It seems to me that the usb adapter isn't hot pluggable (which seems odd for a usb device) or there must be another problem. Polar WebLink (other software to transfer exercise files) experiences the same issue. Can anyone help me to fix this problem? Infrared usb adapter: Polar IRDA USB adapter OS: Ubuntu 12.10 (64-bit) Hardware: Lenovo Thinkpad T500

  Read the article

• 12.04 usb install "boot error"

  - by kindahero

  I downloaded 12.04 64bit, I checked with md5. Seems okay. made bootable usb with usb creater. Now if try to boot up from live usb. I just get "boot error". Nothing else. nothing else. googled around. nothing comes out. UPDATE: some additional info. The usb manufacture is sony. it is fat32 partitioned. Most importantly I could install 12.04 on other systems by same usb. Yes, I definitely setup my Bios boot order to look for USB disk first.

  Read the article

• java serial I/O: handling USB serial connection/disconnection in a robust manner

  - by Jason S

  I'm using rxtx for serial I/O handling in Java with an FTDI2232H that provides a USB comm port. It works great, with one exception: if I unplug the USB cable, so that the COM port disappears at runtime, it spews exceptions left and right: java.io.IOException: No error in nativeavailable at gnu.io.RXTXPort.nativeavailable(Native Method) at gnu.io.RXTXPort$SerialInputStream.read(RXTXPort.java:1427) at gnu.io.RXTXPort$SerialInputStream.read(RXTXPort.java:1339) and when I re-plug the cable in again, it does not recover. Is there any way to get rxtx to work properly with USB comm port connection/disconnection? (I've tried to post to the rxtx mailing list but for some strange reason I cannot send messages even though I am subscribed to the list. I've emailed the list admin and have gotten no response.) If not, is there another serial I/O framework that does?

  Read the article

• How to list all attached USB devices in Visual C++

  - by vinzenzweber

  In Short: I need to detect hotplug events of my USB CDC device by PID/VID and get the corresponding virtual COM port which was created by Windows in Visual C++ and in the end create a dll. I have a USB CDC device which I need to be notified of when connected/disconnected on Windows. My approach is to use RegisterDeviceNotification and an "invisible" Window to receive WM_DEVICECHANGE notifications. This part is working so far. Now as far as I found out I need to get the list of USB devices that is plugged, iterate over it and filter out the devices with my PID/VID? I assume that I am then able to get more informations about the device including the COM port? Is the only way to achieve my goal to use SetupDi calls in setupapi.h? Is using WDK / DDK the only way to achieve my goal? As soon as that is working I open-source it on http://github.com/vinzenzweber/USBEventHandler. The Mac version is available already!

  Read the article

< Previous Page | 60 61 62 63 64 65 66 67 68 69 70 71  | Next Page >