Search Results

Search found 18842 results on 754 pages for 'the machine'.

Page 643/754 | < Previous Page | 639 640 641 642 643 644 645 646 647 648 649 650  | Next Page >

• DPMS does not work: the monitor is not switched off

  - by bortzmeyer

  I have a monitor which was properly switched off by my Debian PC when unused. I attached it to another machine and, this times, it is never switched off. In /etc/X11/xorg.conf, I have: Section "Monitor" Identifier "Generic Monitor" Option "DPMS" It is recognized when X11 starts: (II) Loading extension DPMS ... (II) VESA(0): DPMS capabilities: StandBy Suspend Off; RGB/Color Display ... (**) Option "dpms" (**) VESA(0): DPMS enabled The operating system is Debian stable "lenny". The graphics card is: 00:02.0 VGA compatible controller: Intel Corporation 82G33/G31 Express Integrate d Graphics Controller (rev 02) (prog-if 00 [VGA controller]) Subsystem: Hewlett-Packard Company Device 2a6f Flags: bus master, fast devsel, latency 0, IRQ 5 Memory at fe900000 (32-bit, non-prefetchable) [size=512K] I/O ports at b080 [size=8] Memory at d0000000 (32-bit, prefetchable) [size=256M] Memory at fe800000 (32-bit, non-prefetchable) [size=1M] Capabilities: [90] Message Signalled Interrupts: Mask- 64bit- Queue=0/0 Enable-Capabilities: [d0] Power Management version 2 X11 is: X.Org X Server 1.4.2 Release Date: 11 June 2008 X Protocol Version 11, Revision 0 Build Operating System: Linux Debian (xorg-server 2:1.4.2-10.lenny2) Current Operating System: Linux ludwigVII 2.6.26-2-686 #1 SMP Sun Jun 21 04:57:3 8 UTC 2009 i686 Build Date: 08 June 2009 09:12:57AM

  Read the article

• Unusable network, packet losses between router and NIC

  - by KáGé

  I have this setup: Gigabyte P35-DS3P motherboard Asus NX1101 PCI network card (the one on the motherboard got fried a few years ago by a power surge) Asus RT-N16 router Windows 7 x64 I think the other specs are irrelevant here, but I'll post them if you say so. Until a week ago everything was fine, but then my network became unusable: websites start loading but timeout before anything would come through (true for the web interface of the router as well), I can't reach the computer from my notebook and Windows' ping utility measures a ~50% packet loss between the computer and the router. Pinging localhost is good. The router works completely fine when wired to my notebook. I also tested different ports on the router, different cables, different router and connecting directly to the modem, but it's still the same. Sometimes it works for a few minutes right after turning on the machine, but then it becomes crap again, but mostly it's useless from the start. I've tried updating the firmware on the router, updating the driver for the network card (after which I started getting BSoDs in every 15 minutes), reinstalling Windows, swapping to Fedora 15 but none of them changed anything. Does this mean that the network card is dying, or could it be something else? If it's the card, what model do you recommend as a replacement? (Could be PCI or PCI-Ex x1) Thanks for your help.

  Read the article

• ffmpeg: video file played OK on Ubuntu, but no sound on XP

  - by Andy Le

  I created a video clip using ffmpeg (vcodec: mpeg2video, acodec: AC3 5.1). The file can be played normally on Ubuntu, but when I play it on an XP machine, there is no sound. I can play AC3 files and other movies with AC3 sound. I already tried many codec packs and many players. When I compare the MediaInfo tab of the Properties window of the file with another playable movie, I see that the Audio Identifier of the audio stream in my file is 0x80 while it is 0x02 in the other movie. So I guess that's why players on XP can't recognize the audio codec. When I use an MKV container instead of MPEG (still mpeg2video codec), then the result is OK on both Ubuntu and XP (with the correct Audio ID). I really need MPEG though. Any idea? This is the command I used: ~/ffmpeg/ffmpeg/ffmpeg -loop_input \ -t 97 -r 30000/1001 -i v%4d.tga -i final.ac3 \ -vcodec mpeg2video -qscale 1 -s 400x400 -r 30000/1001 \ -acodec copy -y out6.mpeg 2 This is the output of mediainfo (on Ubuntu): General Complete name : out6.mpeg Format : MPEG-PS File size : 6.86 MiB Duration : 1mn 37s Overall bit rate : 593 Kbps Video ID : 224 (0xE0) Format : MPEG Video Format version : Version 2 Format profile : Main@Main Format settings, BVOP : No Format settings, Matrix : Default Format_Settings_GOP : M=1, N=12 Duration : 1mn 37s Bit rate mode : Variable Bit rate : 122 Kbps Width : 400 pixels Height : 400 pixels Display aspect ratio : 1.000 Frame rate : 29.970 fps Resolution : 8 bits Colorimetry : 4:2:0 Scan type : Progressive Bits/(Pixel*Frame) : 0.025 Stream size : 1.41 MiB (21%) Audio ID : 128 (0x80) Format : AC-3 Format/Info : Audio Coding 3 Duration : 1mn 36s Bit rate mode : Constant Bit rate : 448 Kbps Channel(s) : 6 channels Channel positions : Front: L C R, Side: L R, LFE Sampling rate : 44.1 KHz Stream size : 5.18 MiB (75%)

  Read the article

• Weird rendering artefact in vim (terminal, not MacVim)

  - by Tobi Lehman

  Running Mac OS X, using either Terminal.app or iTerm2, there is a strange artefact with the character rendering that I have a hard time explaining and an even harder time understanding. I'll start with a video of my screen so that you can see and example of it in action: From the video you can see a few ways it is weird, for example, sometimes when I hit a letter in insert mode, the character is double printed. When I go into normal mode, the artefact remains. When I re-enter insert mode, hitting backspace copies the characters on the left to the position under the cursor. This has happened in OS X Lion, and Mountain Lion, under both Terminal.app and iTerm 2. This never happens under MacVim. Also, I use GNU/Linux on my other machine, and have never had this happen, I am pretty sure it is strictly a Mac OS X issue, but I do not know how to fix it. For a while, I've been working around it by using MacVim most of the time, but I prefer working in a terminal. Does anyone know what is happening here, and if so, how can I fix it? EDIT: I tried using the macvim Vim executable, and I still get strange artefacts, but they are localized to the left side of the screen, here is an example:

  Read the article

• ssh-add insists on passphrase

  - by Sam Walton

  I have a new ssh key problem. I have successfully used them for years with Heroku, Git and other servers so I can login without having to issue a passphrase. A few weeks ago, I was unable to push a git repository on my machine to my Heroku and it responded with Permission denied (publickey). Hmm. Everything else but this Heroku function still works. So I ssh-keygen -t rsa -C "newHeroku" with no passphrase (hit return so it would be empty). So I enter: sudo chmod 600 ~/.ssh/newHeroku* Then: ssh-add ~/.ssh/newHeroku.pub Returning return for the passphrase asked it exits without error. The next step is to: ssh-add /Users/sam/.ssh/newHeroku.pub To verify that it's "live" I enter: ssh-add -l To which the output is still The agent has no identities. Okay, to eliminate variables, I repeat the key generation process but entering in a passphrase for a new key. I ssh-add the new key and get the "Enter passphrase" as expected. Now this is why I'm posting here and not on a Heroku blog because ssh-add fails because the passphrase I used keeps getting rejected. It appears, even though I have no problem with my keys elsewhere, that something is wrong with passphrase because even though I get no errors, I get errors when on the one that expects a passphrase. One question, should I expect the Passphrase request for ssh-add when I have not generated a passphrase? It's been suggested that this is a clue and I offer it. Or maybe I have a poor understanding of what ssh-add is doing. Wouldn't be the first time I asked a stupid Q. Also, I'm on Lion and have updated no system updates in the few weeks of this period except application updates.

  Read the article

• In Windows 7, why won't my display stay off despite the power settings saying it should?

  - by Jer

  I'm completely stumped by this. My simple use case is that when I'm in bed, I use a cordless mouse to browse the web, watch videos, etc. - the monitor is across the room. When I'm going to sleep, I want to shut the monitor off. I also want to be able to turn it back on in the morning. I just want to turn the monitor off and on using only the mouse. I thought of creating a power setting that turned the monitor off asap (the shortest amount of time is one minute; that's fine). I have one that does this. It worked great for almost a year on my old XP machine, and for about four months on my new Windows 7 laptop (which I essentially use as a desktop). All of a sudden a couple weeks ago, it just stopped working - my monitor won't turn off on its own anymore. Here are the settings: I tried other options. Based on the advice here I tried nircmd. This seemed great. I created a shortcut with the command line: "C:\Program Files\nircmd\nircmd.exe" cmdwait 1000 monitor off I click this, and in one second the monitor goes off. However about five seconds later it turns back on, and I've been extra careful to make sure the mouse isn't moving. I have no idea what's going on. Based on both of these things, my only guess is that something could be running in the background which somehow makes the computer think it's in use. I've tried killing as many programs as possible but I still get the same behavior. Any advice? I'm mainly curious about how to debug, but am open to other suggestions about turning the monitor off and on with just the mouse as well.

  Read the article

• Linux Cups raspberry pi offload processing to server

  - by jaredmsaul

  I am interested in setting up a raspberry pi as the local end of a printing solution. In my testing the pi chokes on acting as a complete cups based print server. It seems a little underpowered for some of the ghostscipt processing and other filtering that occurs-- particularly on larger or complex documents the processing time can be 5 or more minutes. My question is can the processing be largely done elsewhere and the prepared end product of the processing chain be fed to the pi for output on the connected printer? So in this scenario any arbitrary document (html, pdf, text) is initially 'printed' on a relatively powerful machine but the output is stored in a file. This file is then grabbed by the pi and with all the heavy work out of the way easily printed using cups. I know files can be pushed through cups in raw mode but I am fuzzy on the pros and cons and the applicability in what I describe. I have tested this with pdftops creating a ps file then feeding that raw to cups and I think it works but it seems like there may be a cleaner solution. This scenario would ideally work for any number of printer types.

  Read the article

• I go to www.facebook.com, but a completely different site appears.

  - by Rosarch

  I am going to www.facebook.com, but the site that appears is totally different. This occurs on Chrome 6+, IE9, and FF 3+. What could be happening? Is this a security risk? Facebook was working just fine, then all of a sudden this happened. Update: The same problem occurs on my netbook. Update 2: When I go to http://69.63.189.11/, it works fine. So... DNS problem? How do I fix? Update 3: Checked the hosts file: # Copyright (c) 1993-2009 Microsoft Corp. # # This is a sample HOSTS file used by Microsoft TCP/IP for Windows. # # This file contains the mappings of IP addresses to host names. Each # entry should be kept on an individual line. The IP address should # be placed in the first column followed by the corresponding host name. # The IP address and the host name should be separated by at least one # space. # # Additionally, comments (such as these) may be inserted on individual # lines or following the machine name denoted by a '#' symbol. # # For example: # # 102.54.94.97 rhino.acme.com # source server # 38.25.63.10 x.acme.com # x client host # localhost name resolution is handled within DNS itself. # 127.0.0.1 localhost # ::1 localhost Looks like it hasn't been altered.

  Read the article

• How to record tv to network share with Windows Media Center?

  - by Peterdk

  Well, you would think that Windows 7's new MediaCenter would be up to the task of recording your TV to a network share/drive. Too bad, it looks like it's just not possible. I have a windows 2008 R2 server, and a Windows 7 machine with a TV card. Since my server has 2TB of storage, it would be nice to record directly to it's networked drive. (I mounted it as Z:). I tried the following: Selecting it in Media Center Itself: Not working. Not available. Editing the registry: HKEY_LOCAL_MACHINE\SOFTWARE\Microsoft\Windows\CurrentVersion\Media Center\Service\Recording , setting RecordPath to Z:\TV. Not working. Editing the registry: setting RecordPath to \\server\TV. Not working. Creating a Symlink (mklink \D) to Z:\TV and \\server\TV and setting that in the registry as RecordPath. Currently I am out of options. I could ofcourse Install Windows7 on my server, but I have no license for that, and my windows 2008 r2 is free from dreamspark. Are there people that are succesfully recording to a networked drive/storage? edit I also need to mention that I need to be able to acces the stored files from other PC's, like my laptop. So iSCSI is great for recording, but it looks like you can't access iSCSI devices from multiple PC's. Looks like sharing a iSCSI device is out of the question, so: Are there workarounds to get this thing recording to my network drive?

  Read the article

• How to better copy&paste big files over RDP?

  - by WebMAOhist

  Recently I was making a few attempts to copy&paste a big (1.2 GB) file to remote computer over RDP. The remote computer is virtual testing machine with MS Windows Server 2008 Datacenter. First I tried to copy&paste before midnight when the transfer speed was limited by client computer ISP to 100 kB/s. So, it required a few hours and I was forced to cancel transfer since remote desktop became too unresponsive and sluggish (slow). So, I re-started it over midnight when my local transfer speed is over 4 GB/s 4MB/s (sorry for typo). So, my impression is that independently on speed (broadband) of copy&paste transfer the remote computer becomes sluggish while copying over RDP. At the same time downloading from internet doesn't make remote host sluggish. AFAIU, it is because clipboard of remote computer and so its memory becomes overloaded by transfer. How can I control (restrict) the usage of clipboard for specific process (pasting of file)? What are the possible way to control it? Update: After reading that slow speed of transfer is caused by encryption used for copy&pasting over RDP and since I believe I am more interested in overall efficiency: both the time, or rapidness, of getting file as well as possibility to work without waiting, I changed the question title from: How to control the usage of remote desktop clipboard usage for pasting a big file? to How to better copy&paste big files over RDP? For example, is it better to copy&paste one huge (zip) archive or unzip it and copy paste a folder with unzipped files? And more exactly I wanted to ask: What are possible ways to improve overall experience: the speed of transfer (i.e. availability of needed file) responsiveness of remote host (making remote coputer available for work before completion of copy&pasting)?

  Read the article

• Why is windows not able to create a system partition?

  - by hughes

  I'm reinstalling Windows 7 64 bit, and I encountered an issue I've never seen before. I have a legit copy of Win 64 Professional, and I've installed it probably a half dozen times on this machine in the past without a problem. Googling the error only brings me to issues with people who are upgrading to win7. The drive itself seems to not have a problem. I can mount it on other systems and I can create an NTFS partition on it on other machines. I can install Ubuntu on it without any issues. Additionally, if I try using my alternate backup hard drive, the installer gives the same error. I have run diskpart from the setup page and clean seems to report that all is well. However, I cannot get past the screen below, which says Setup was unable to create a new system partition or locate an existing system partition. This happens regardless of whether or not the disk space is already allocated. What is causing this? How do I solve or get past this?

  Read the article

• Creating security permissions for a non-domain-member user in Windows Server 2008

  - by Overhed

  Hello everyone, I apologize in advance for incorrect use of terminology, as I'm not an IT person by trade. I'm doing some remote work via a VPN for a client and I need to add some DCOM Service security permissions for my remote user. Even though I'm on the VPN, the request for access to the DCOM service is using my PCs native user (and since I'm running Vista Home Premium it looks something like: PC-NAME\Username). The request for access comes back with access denied and I can not add this user to the security permissions as it "is not from a domain listed in the Select Location dialog box, and is therefore not valid". I'm pretty stuck and have no clue what kind of steps I need to do here. Any help would be appreciated, thanks in advance. EDIT: I have no control over what credentials are being passed in to the server by my computer. This scenario is occurring in an installation wizard that has a section which requests you point it to the machine running the "server" version of the software I'm installing (it then tries to invoke the relevant COM service, but my user does not have "Remove Activation Permissions" on that service, so I get request denied).

  Read the article

• kvm-over-ip, multiple machines per cable run

  - by Sirex

  I'm looking at getting a kvm-over-ip setup for a server room. Typically these devices have 16 or so cat5 leads that come out of them and then a convertor that converts each cat5 into a vga & ps2 pair. Can you run one cable from the unit into a switch, and then leads from the switch into each machine ? I have several machines on the other side of the server room that i'd like to have avaliable but i dont want to run 16 cables to them. I'm thinking this should be possible being IP layer and all, but as each device normally has its own cable out the back of the kvm unit i'm not certain. Perhaps the kvm's rear ports act essentially like a switch anyway in which case it should work, or perhaps if i run all 16 cables into a seperate switch right next to it and aggregate the ports together, run one cable to a switch on the other side of the room with similar number of ports agregated together, then use that switch to plug each macine into ? I'm fairly sure this is possible, but i just want to check before i shell out the cash as i've never tried it.

  Read the article

• dom0 enable IPv6 for guests

  - by user98651

  I am looking at deploying IPv6 to my virtual machines. Right now I have v6 working great on the dom0 using a 6in4 provided by Hurricane Electric as I do not have native v6. However, I would like to distribute some of the /48 I am receiving to the domUs (/64 per machine would be ideal, but I am open to your suggestions). Static configuration on the domU side is fine. All I want to accomplish is getting the traffic to pass through the dom0 to the domU. To say the least, I'm still trying to wrap my head around all the virtual interfaces and bridges Xen creates. Yes, I have Googled around for this a bit and have not found anything great. I tried using two "vif-route6" bash scripts with no luck (possibly due to my ignorance with Xen networking). I am still stuck (mainly in how to configure the dom0). I would like to imagine this problem is relatively easy to solve and I look forward to your suggestions and help! Edited post to clarify my end goal: getting IPv6 to domU guests. I am completely open to suggestions but am hoping for something other than setting up a tunnel for every guest.

  Read the article

• Software to monitor bill payment to mission critical IT service providers (ISP, DNS etc.)

  - by Sholom

  Hi All, The Problem: Our very likable but absent minded bookkeeper keeps neglecting to pay our IT vendors on time. Just this past week our internet service was disconnected. Same could happen to many other mission critical accounts (domain registrar, backup MX, anti-virus license, HackerSafe (McAfee secure) service and even an 800 number to name a few). As the sysadmin, i monitor my severs to make sure they are plugged into the power-outlet. I believe i should also monitor my services to make sure they are plugged in to their money-outlet. To compound the problem, when the power goes out someone else will likely notice and notify me. But if a bill is not payed, no one will ever notice until service is lost. Lost as in losing our domain name which would cause a lot more damage then the power failing on our server. [Solution] = [Doesn't work because]: Retrain the bookkeeper = Wishful thinking. Notify my manager = Already have (via email). Protects me, does not solve problem. Fire bookkeeper = What makes you so sure the next one will never forget? Bottom line: Humans are humans and sooner or later something critical will be royally messed up. We need to partner with a machine to help us out here. Anybody have the same problem? What software/solution do you use? I would like software that emails me when a bill is passed due just like i get an email when the power outlet fails. Anyone hear of anything like that? Thanks

  Read the article

• Copying files between linux machines with strong authentication but without encryption

  - by Zizzencs

  I'm looking for a suitable program to copy files from one linux machine to another one. The program should be able to do authentication but it should not do encryption. The reason behind the latter is the lack of CPU power to do the encryption. I copy backups from ~70 machines to a single backup server simultaneously. The single server is an HP Proliant DL360 G7, with 10 Gbps ethernet connection and an FC storage backend that can do 4 Gbps. Through FTP I can write ~400MB/sec to the storage (that's about what I want) but through ssh with arcfour I can only do ~100MB/sec while having 100% CPU usage. That's why I want file transfers not to be encrypted. The alternatives that I found not really suitable: rcp: no authentication, forget it FTP: making the authentication "secure" (at least preventing plain-text password exchange) is possible but not really easy and I haven't found a method to force any FTP daemon to encrypt the control channel (for the authentication) and not to encrypt the data channel (for data transfers) SCP/SFTP: in farely recent ssh(d) implementations you can't turn off encryption. The best you can do is to use the arcfour cypher for the encryption but it sill uses too much CPU power for my needs. rsync over ssh: same problems as with SCP/SFTP. plain rsync: from the documentation of rsyncd: "The authentication protocol used in rsync is a 128 bit MD4 based challenge response system. This is fairly weak protection, though (with at least one brute-force hash-finding algorithm publicly available), so if you want really top-quality security, then I recommend that you run rsync over ssh." It's a no-go. Is there a protocol/program that can do exactly what I want? (A big plus would be if it could work on windows as well and/or if it would support rsync-stlye copying/synchronization (e.g. copy only the differences).)

  Read the article

• NTBackup (on WS2k3) fails to backup remote server (WS2k8R2) with " Error: is not a valid drive, or you do not have access."

  - by Mark A

  We run an NTBackup job on a Windows Server 2003 R2 SP2 with all updates (as of Q4-2011). It works well backing up two WS2k3 servers as well as the backup server itself. However, we have been unable to successfully back up our Windows Server 2008 R2 machine ("G5-01"). It often runs for about 2GB worth of backup and then dies out with one of the below error messages. It should be more like 20GB for the full server. We have tried using the admin share (C$), an explicitly shared drive share, UNC and mapped drives. The result is the same each time, the only thing that varies is the amount of stuff backed up before it chokes. We've also run NTBbackup from the UI interface, from the command line and as a scheduled task. We are backing up to 400/800GB tapes and they have plenty of space available on them (blank media). Error: \\G5-01\c is not a valid drive, or you do not have access. Error: \\G5-01\c$ is not a valid drive, or you do not have access. Error: Y: is not a valid drive, or you do not have access. Error: Could not access or create backup catalog files. Verify that you have full access to the working folder and there is disk space available. The job is run as Administrator and we have no problems logging onto the server and transferring files. The Event Log on the WS2k8 is not much help, as it has success audits for each login. All of the hardware involved (HP DL360 G3, HP LTO Ultrium 3, Adaptec 39320A) has the latest supported drivers. We've seemingly tried a bunch of different options but are wondering where to look next to resolve the backup issue. We've been super happy with our reliable schedule task for years but this one is stumping us!

  Read the article

• Create account for service

  - by Andy

  I am configuring a new server. The server is running Hudson that is going to copy some files from this server to another. The other server is a virtual machine. Both running Windows Server 2012. Hudson is started on server A with log on as "Local System". When I come to the copy phase it says "Access denied". Changing the log on to "Administrator" works. However, I guess this is bad. I do not have much experience with user management. I tried to create a own hudson account on both servers A and B. I tried to log on as hudson account in the service-management but it doesn't start. How would you create an account for this particular service that has access to the shared folder on server B and can be used to start the service on server A? I guess I need two accounts with same username and password on server A and server B? The folder on Server B is shared with everyone and the guest account is enabled.

  Read the article

• Poor write performance on Debian server running NFS with 22TB exported JFS filesystem

  - by user143546

  I am currently running a debian server that is exporting a large JFS filesystem (22TB) over NFS (nfs-kernel-server.) When attempting to write to the NFS share, the performance is very poor. The 22TB disk is sitting on a NAS mounted using iSCSI. It will bust for a moment near expected line speed, and then sit idle for several seconds. Very little traffic measured in the low kb/sec. The wait peeks on write. When reading from the NFS mount, the system operates at expected speeds (11MB/sec). The issue does not occur when using SFTP, rsync, or local coping (non-nfs). The issue persists between stable and testing releases. On the same machine I have a 14TB ext4 filesystem using the exact same export configuration that does not share the issue. This share is not in regular use and thus not consuming resources. NFS Server: cat /etc/exports /data2 10.1.20.86(rw,no_subtree_check,async,all_squash) cat /sys/block/sdb/queue/scheduler noop [deadline] cfq cat /etc/default/nfs-kernel-server RPCNFSDCOUNT=8 RPCNFSDPRIORITY=0 RPCMOUNTDOPTS=--manage-gids NEED_SVCGSSD= RPCSVCGSSDOPTS= NFS Client: cat /etc/fstab 10.1.20.100:/data2 /root/incoming nfs rw,noatime,soft,intr,noacl 0 2 cat /sys/block/sdb/queue/scheduler noop [deadline] cfq cat /proc/mounts 10.1.20.100:/data2/ /root/incoming nfs4 rw,noatime,vers=4,rsize=262144,wsize=262144,namlen=255,soft,proto=tcp,port=0,timeo=600,retrans=2,sec=sys,clientaddr=10.1.20.86,minorversion=0,addr=10.1.20.100 0 0 This problem has me pretty stumped. Any help would be greatly welcomed. Thanks.

  Read the article

• Connection failed between Windows Servers

  - by Kerby82

  I'm setting up an infrastructure based on Windows Server 2012. The firewall is turned off and I can't access the Domain controller to check for the group policy. I'm experiencing some connection problem between servers. All the servers are running a site on the TCP Port 80 and I check with netstat that the web server is binding on every Ip of the servers. If i try to telnet from the server itself on the port 80 it works (using DNS name) if I try same telnet from another machine I get connection failed. The DNS works, the ping is successfull, the servers are on the same subnet, the firewall is turned off (even though windows advanced firewall says that some settings can be managed by the System Administrator, i guess group policy). I don't know how to troubleshoot further. Do you have any idea? Is that possible that the FW looks turned off but there are some group policy blocking the connections? (I also check group policy-Administrative Template-Network Connections- Windows FW everything is not configured) I need some hint on how to keep troubleshooting such a problem.

  Read the article

• Can't connect to Server Manager from Windows 7

  - by SAdmin317

  I have a Windows 7 Pro 64bit with SP1 desktop that has RSAT tools installed. I opened Server Manager and can't connect to the server (Server 2008 R2 core). I followed the guide to enable everything on the server, added a registry key to enable read-only on the device manager as well. On the Windows 7 PC I turned on winrm, did the quick config, and added the server IP and name as trusted hosts. I still get an error when connecting. "Connecting to the remote server failed with the following error message: The WinRM client cannot process the requests. If the authentication scheme is different from Kerberos, or if the client computer is not joined to a domain, then HTTPS transport must be used or the destination machine must be added to the TrustedHosts configuration setting...." I also added the name of the server to the windows 7 /etc/hosts file. Ping the server name translates to the IP of the server. Also opened up the firewall for "Remote Volume Management" Both machines are on the same Workgroup, using the same Administrator account, with the same password. Any help appreciated.

  Read the article

• VMWare web UI intermittent access on CentOS

  - by PeteWilliams

  I've got a CentOS 5.2 server that I'm trying to get set up as a development environment. As part of this, I planned to install VMWare Server 2 and set up several virtual development servers. I've got as far as installing VMWare Server 2 but access to the remote control panel is only working intermittently. If I access it through Firefox at https://127.0.0.1:8333/ui/# it usually says either: "Connection intterupted: connection was reset before the page loaded" Or "Firefox can't establish a connection to the server at 127.0.0.1" But every now and then it lets me in and I'll manage a few clicks in the web UI before it kicks me out with the following error: "The server could not complete a request (HTTP 0 ). The server encountered an unexpected condition that prevented it from fulfilling the request. If this problem persists, please contact your system administrator." I've done all the updates available in CentOS except one OpenOffice one that is causing a conflict, and I re-ran wmware-config.pl after updating the kernel. Though I went with all the defaults as I don't really know what I'm doing! I've since rebooted and nothing changed. I've also tried accessing the control panel remotely from another machine in the network and the results are the same. Does anyone have any ideas what might be causing this and how I can resolve it? I'm afraid I'm a developer playing at sys-admin, so I may be missing something obvious! Many thanks Pete Update I have now reinstalled both the operating system and VMWare and I'm still getting the same issue. I wonder if it's a result of the settings I'm putting in on the config.pl script..?

  Read the article

• Windows 7 Blank Screen on Boot / Login

  - by Greg

  I have a new system that's having a few problems... sometimes (seems to be when the PC is cold, i.e. has been switched off for a while, though that could be my imagination) I get a blank blue screen when I boot up. The system boots normally and auto-logs-in. The desktop loads and I'm even able to launch applications, but then everything disappears and the screen goes to the default windows desktop blue colour (not the desktop image, just a plain blue with no mouse cursor). At this point the machine completely locks up - I'm unable to even toggle Num Lock and have to hold in the power button for 5 seconds to kill it. Interestingly if I manage to launch some applications before it goes blank, they will usually crash... sometimes explorer.exe will crash too. When I reboot, the system is fine and stable. I've installed the latest graphics drivers and run memtest86+ for 6 passes (and counting) with no errors. The system specs are: CPU: Intel I7 2.66 @ 3.4GHz RAM: 6GB (3 * 2GB DDR3) HDD: 128GB Crucial M225 SSD Motherboard: Gigabyte EX58-UD3R Gfx: ATI Radeon Sapphire 5870 1GB Note: There are a few similar questions but I haven't found one that matches my symptoms

  Read the article

• How do I connect to SSH without the password to be requested every time ? - Already follow some answers here but it doesn't work

  - by MEM

  MAC OS X Lion 10.7.3 1) On host, I've created an authorized_keys file inside .ssh folder, by doing: touch authorized_keys 2) I've copy my public ssh key into host .ssh folder by doing: scp ~/.ssh/mykey.pub [email protected]:/home/userhost/.ssh/mykey.pub 3) I've place it's contents inside authorized files by doing: cat mykey.pub >> authorized_keys 4) Then I've removed the mykey.pub file: rm mykey.pub 5) On my terminal, locally, inside my ~/.ssh folder I made: ssh-add mykey (notice that it is without the pub extension); 6) I've closed and opened again the terminal. When I first connect to this host, it has being added to the *known_hosts* file inside ~/.ssh; I've pico known_hosts and the hash is there. Still, every time I connect by doing: ssh [email protected] it requests a password ! What am I missing here ? UPDATE: I've done EVEN TWO MORE THINGS here: 7) Set your key to be the default identity - if it doesn't exist, create; touch ~/.ssh/config and place inside the following line: IdentityFile ~/.ssh/yourkeyname *id_rsa is normally your default key. You should switched to your key. This tells that the outgoing ssh connections should use this as a default identity.* 8) Add a bash process to your ssh-agent: ssh-agent bash ssh-add ~/.ssh/yourkeyname Lisinge answer helped but it's not definitive. If we restart our machine, the password gets prompted again!!! How can we debug this? What can we do here? How can we check where is this process failing ? UPDATE 2: If I use: ssh -v -i <keyfile> [email protected] I get among other things: OpenSSH_5.6p1, OpenSSL 0.9.8r 8 Feb 2011 Warning: Identity file yourkeyname not accessible: No such file or directory. This message refers to what? The identify file is not accessible on the localhost, or it's not accessible on the remote host ? Please advice

  Read the article

• Windows Media Center showing Jerky Video on PC

  - by Kris Erickson

  I had to repave my Windows 7 x64 box last week due to a hard drive crash, and for a while everything was running perfectly but now all videos in Windows Media Center are jerky (the sound is fine, they just seem to skip a ton of frames all the time). This is on the local machine, but the same thing happens when I try to stream to my Xbox. The videos all show fine in VLC and Windows Media Player (however exhibit the same problem in Quicktime). I guess I must have installed something recently (in the process of getting all the apps I usually have running on my PC) that caused this but for the life of me I can't figure it out. I have updated to the latest video driver (and then rolled back to the standard Windows 7 driver), I have rolled back all the other drivers that I have installed (I believe). I have uninstalled all the codec packs (I also run TVersity, so I have the TVersity codec pack installed), and I uninstalled TVersity. Nothing seems to help. I have uninstalled windows media center, and reinstalled it from the Programs and Features. I have basically ran out of things to try to fix this, and am almost thinking about reinstalling Windows again. Any suggestions? Edit Specs on the PC (which I figured was unimportant since everything used to work perfectly): Intel Core 2 CPU 6600 @ 2.4 Ghz Nvidia GTS 8800 Built in realtek-audio soundcard 4GB Ram Codecs which are failing: All that I have tried, but at least Xvid, Mpgv (mpeg2 video from a camera), and Wmv (only kinds that I have ready access to).

  Read the article

< Previous Page | 639 640 641 642 643 644 645 646 647 648 649 650  | Next Page >