Search Results

Search found 19701 results on 789 pages for 'disk images'.

Page 648/789 | < Previous Page | 644 645 646 647 648 649 650 651 652 653 654 655  | Next Page >

• Experience with AMCC 3ware 9650se raid cards? Ours seems dead

  - by antiduh

  We have a 8-port 3ware 9650se raid card for our main disk array. We had to bring the server down for a pending power outage, and when we turned the machine back on, the raid card never started. This card has been in service for a couple years without problems, and was working up until the shutdown. Now, when we turn the machine on, the bios option rom that normally kicks in before the bootloader doesn't show up, none of the drives start, and when the OS tries to access the device, it just times out. The firmware on it has been upgraded in the past, so it's possible we've hit some sort of firmware bug. We're using it in a Silicon Mechanics R272 machine with gentoo for the OS. The OS eventually boots, but alas, without the card. We've ordered a new one, but I'm worried that if we replace the card it won't recognize the existing array. Has anybody performed a card swap before? Any help would be greatly appreciated. Edit: These are the kernel errors we see: 3ware 9000 Storage Controller device driver for Linux v2.26.02.012. 3w-9xxx 0000:09:00.0: PCI INT A -> GSI 18 (level, low) -> IRQ 18 3w-9xxx 0000:09:00.0: setting latency timer to 64 3w-9xxx: scsi0: ERROR: (0x06:0x000D): PCI Abort: clearing. 3w-9xxx: scsi0: ERROR: (0x06:0x001F): Microcontroller not ready during reset sequence. 3w-9xxx: scsi0: ERROR: (0x06:0x0036): Response queue (large) empty failed during reset sequence. 3w-9xxx 0000:09:00.0: PCI INT A disabled

  Read the article

• Atlassian Crucible very slow on large repository

  - by Mitch Lindgren

  Hi everyone, My company has been running a trial of Atlassian Crucible for some months now. For repositories where it's working properly, users have given very positive feedback about the tool. The problem I'm having is that we have several different projects, each with its own repository, and some of those repositories are very large. One repository in particular has a large number of branches and probably around 9,000 files per branch. Browsing that repository in Crucible is extremely slow. Crucible is running on a CentOS VM. The VM has 4GB of RAM, and I've set Crucible's maximum at 3GB, of which it is currently using 2GB. I've brought this up in a support ticket with Atlassian, and they suggested the following: In particular because you have a rather large SVN repository you will likely find that Fisheye will be creating a large index file on disk. To help improve performance a few things you can try are: Increasing the available memory available to Fisheye (see the document above). Migrating to an external database: confluence.atlassian.com/display/FISHEYE/Migrating+to+an+External+Database Excluding files and directories from your index that aren't needed: confluence.atlassian.com/display/FISHEYE/Allow+(Process) (Sorry for not hyperlinking; don't have the rep.) I've tried all of these things to an extent, but so far none have helped greatly. I was originally running Crucible on a Windows box with 2GB of RAM using the built in HSQL DB. Moving to MySQL on CentOS saw a performance increase for some repositories, and made Crucible much more stable, but did not seem to help much with our biggest repository. There are only so many files/branches I can exclude from indexing while maintaining the tool's usefulness. That being the case, does anyone have any tips on how to speed up Crucible on large repositories, without investing in insanely powerful hardware? Thanks! Edit: To clarify, since I didn't mention it explicitly above, I am using FishEye.

  Read the article

• How to add a Linux Partition on FreeBSD

  - by Ömer

  Today I installed FreeBSD 9.0 PPC on my Mac mini G4 with 40GB HDD. During installation, (using the FSBD utility 'gpart') I have allocated a total of about 23GB for FreeBSD leaving 17GB totally free (neither partitioned, nor formatted) for a later Linux installation. Now, when try to install Linux (Ubuntu 10.10 PPC) on the remaining 17GB, the Linux/Ubuntu installer (or Linux's Disk Utility for the same matter) wants presumably a linux partition and when I try to add a (Linux) partition on that area using Linux DU it fails with this message: Error creating partition: helper exited with exit code 1: In part_add_partition: device_file=/dev/hda, start=23363101696, size=16644660224, type= Entering MS-DOS parser (offset=0, size=40007761920) No MSDOS_MAGIC found Exiting MS-DOS parser Entering Apple parser Mac MAGIC found, block_size=512 map_count = 17 Leaving Apple parser Apple partition table detected containing partition table scheme = 2 got it Error: The partition's data region doesn't occupy the entire partition. ped_disk_new() failed Now, I'm trying to add a Linux partition on FreeBSD running on the harddisk. I use seemingly most suitable tool for this job: gpart. Here is the 'gpart show ad0' But it seems unable to add a Linux partition because "man gpart" doesn't list either "Linux Partition" nor anything like Ext2 or Ext3/Ext4. The closest thing to Linux Partition in gpart is "mbr" but it doesn't work: #gpart add -t mbr ado So, how to add properly a Linux Partition on FreeBSD? Thanks.

  Read the article

• Windows 7 AIK help

  - by microchasm

  I've just got in a few Windows 7 (64, Windows 7 Professional) machines, and I'm trying to get the AIK 2010 working. I've set up one of the machines, and installed AIK and MDT on it. I've followed the directions at http://technet.microsoft.com/en-us/library/dd349348%28WS.10%29.aspx about 3 times now, and also tried the built-in .chm help files that came with AIK. In AIK I grab the install.wim image off the OEM cd, at which point it asks me which version (I select Professional). I follow the rest of the instructions creating a new Autounattend answer file, and fill in the various bits and pieces according the the step-by-step guides. I verify the Answer file (No warnings or errors), save it, and copy it onto a USB drive. I go to another machine, insert it's OEM Win7 Disk, and power on. I've set BIOS to boot from CD, so it goes directly into the installation. Once The files are loaded, and Setup starts, it immediately asks which version to install (Home basic, Home Premium, Professiona, Ultimate). Ugh, I thought it was supposed to be an automated install, and that selecting the Version when opening the .wim file would answer this question. I looked for an option to set which version to be installed on the net, in the help, and in AIK itself; to no avail. Anyway, just for laughs I select Professional,and hit continue. It copies files for about 10 seconds, then fails with the following error: "Setup was unable to create a new system partition or locate an existing system partition. See the setup log files for more information. [OK]". Clicking OK reboots the box, and obviously there are no log files because the OS isn't installed. It is a Dell Optiplex 380 , Intel Core Duo 2.93 GHzl 4 GB RAM, 64 Bit. Any help would be REALLY appreciated.

  Read the article

• Xen HVM networking wont work

  - by Nathan

  I'm trying to get a Xen HVM network working using route however I am failing. Xen PV works fine using Ubuntu but when installing Ubuntu on HVM it fails to pick up the network. I'll let you know now that I'm not that experienced with Xen so I would appreciate any help. vm104 is the HVM thats causing me the problems, here is the configs that I believe should help resolve the problem. [root@eros vm104]# cat vm104.cfg import os, re arch = os.uname()[4] if re.search('64', arch): arch_libdir = 'lib64' else: arch_libdir = 'lib' kernel = '/usr/lib/xen/boot/hvmloader' builder = 'hvm' memory = 6000 shadow_memory = '8' cpu_weight = 256 name = 'vm104' vif = ['type=ioemu, ip=85.25.x.y, vifname=vifvm104.0, mac=00:16:3e:52:3d:fe, bridge=xenbr0'] acpi = 1 apic = 1 vnc = 1 vcpus = 4 vncdisplay = 3 vncviewer = 0 vncconsole = 1 vnclisten = '217.118.x.y' vncpasswd = 'kCfb5S4tE7' serial = 'pty' disk = ['phy:/dev/vpsvg/vm104_img,hda,w', 'file:/home/solusvm/xen/iso/Windows-Server-2008-RC2.iso,hdc:cdrom,r'] device_model = '/usr/' + arch_libdir + '/xen/bin/qemu-dm' boot = 'cd' sdl = '0' usbdevice = 'tablet' pae=1 [root@eros /]# cat /etc/xen/xend-config.sxp | egrep -v "(^#.*|^$)" (xend-unix-server yes) (xend-unix-path /var/lib/xend/xend-socket) (xend-relocation-hosts-allow '^localhost$ ^localhost\\.localdomain$') (network-script network-route) (vif-script vif-route) (network-script 'network-route netdev=eth0') (dom0-min-mem 256) (dom0-cpus 0) (vnc-listen '0.0.0.0') (vncpasswd '') (keymap 'en-us') The Windows install will not pick up the network - I've tried setting the IP manually by using the Xen servers IP as the gateway and setting the main IP in Windows but no luck. If anyone needs any more information let me know and I appreciate any input!

  Read the article

• Postfix installation error on Ubuntu

  - by kgpdeveloper

  How do I fix this error on Ubuntu 10.04 ? Reading package lists... Done Building dependency tree Reading state information... Done postfix is already the newest version. The following packages were automatically installed and are no longer required: libaprutil1-dbd-sqlite3 libcap2 apache2.2-bin libapr1 libaprutil1-ldap libaprutil1 php5-common Use 'apt-get autoremove' to remove them. 0 upgraded, 0 newly installed, 0 to remove and 1 not upgraded. 1 not fully installed or removed. After this operation, 0B of additional disk space will be used. Setting up postfix (2.7.0-1) ... Postfix configuration was not changed. If you need to make changes, edit /etc/postfix/main.cf (and others) as needed. To view Postfix configuration values, see postconf(1). After modifying main.cf, be sure to run '/etc/init.d/postfix reload'. Running newaliases newaliases: warning: valid_hostname: numeric hostname: 202002 newaliases: fatal: file /etc/postfix/main.cf: parameter myhostname: bad parameter value: 202002 dpkg: error processing postfix (--configure): subprocess installed post-installation script returned error exit status 75 Processing triggers for libc-bin ... ldconfig deferred processing now taking place Errors were encountered while processing: postfix E: Sub-process /usr/bin/dpkg returned an error code (1) Even if I reboot, the same error shows up. Thanks for the help..

  Read the article

• Building new computer, turns on, but no post

  - by addybojangles

  Pardon my ignorance here, finally decided to put together a computer and egads. I purchased a new motherboard, power supply, processor, video card and memory. ASUS M4A79XTD EVO AM3 AMD 790X ATX AMD Motherboard OCZ Fatal1ty OCZ550FTY 550W ATX12V v2.2 / EPS12V SLI Ready 80 PLUS Certified Modular Active PFC Power Supply AMD Phenom II X4 965 Black Edition Deneb 3.4GHz 4 x 512KB L2 Cache 6MB L3 Cache Socket AM3 125W Quad-Core Processor XFX HD-577A-ZNFC Radeon HD 5770 (Juniper XT) 1GB 128-bit GDDR5 PCI Express 2.0 x16 HDCP Ready CrossFireX Support Video Card G.SKILL 4GB (2 x 2GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800) Dual Channel Kit Desktop Memory Model F3-12800CL9D-4GBNQ (originally had links for you guys, but I lack the rep, sorry!!) And I've got it all in the tower. I put in power supply, installed processor on motherboard, installed heatsink, put in ram, and I am using an older IDE hard disk. When I start the computer, the monitor tells me "check signal cable." As far as I can tell, the heatsink on the processor is spinning, the power supply is on (obviously), and the green LED on the motherboard is on. I originally only had the bigger output plugged in to the motherboard (what I saw in a YouTube vid as well as the mobo instructions), but after doing some research, it said plug in the other ATX power supply. Which I did. And trying to power the computer results in nothing. No beeps on startup, no post, anyone have any ideas? Your ideas and help is greatly appreciated.

  Read the article

• What are the advantages and disadvantages of the various virtual machine image formats?

  - by Matt

  Xen and Virtualbox etc both support a range of different virtual machine image formats. These are: vmdk, vdi, qcow & qcow2, hdd & vhd. Without any bias toward a particular product, I'm wanting to know what are the advantages and disadvantages of the various formats both from a features perspective, robustness and speed? One piece of info I discovered in a forum post was this: "The major difference is that VDI uses relatively large blocks (1MB) when growing an image, and thus has less overhead for block pointers etc. but isn't ultimately space efficient in the sense that if a single byte is non-zero in such a 1MB block the entire space is used. VMDK in contrast uses 64K blocks, and thus has more management overhead and generally a bit less disk space consumption What offsets this is that VDI is more efficient when it comes to snapshots." You might be thinking, I want to know this because I want to know which format to choose? Not exactly, I'm developing some software which utilises these formats and want to support one or more of them. Simplicity, large disks and ease of development are my main drivers.

  Read the article

• Digital Asset Management, iPhoto / Aperture server... alternative

  - by Sisyphus

  Afternoon, Clients, 10 : All Apples running either Leopard or Snow Leopard Server : Snow Leopard server, (and I have a old Dell Poweredge 650 at home running Gentoo 2.6, if anybody as a Linux solution). The situation: I work in small design company with 8 people, at present we are looking to consolidate all our image files onto one location, at present we each use our preferred single user DAM solution, be it, Adobe Bridge, iPhoto/Aperture (some don't bother at all) The filetypes commonly used are .psd, .pdf, .eps, .tiff, .jpg and RAW image files. Ideally what is needed: Centralised on one server, but allows us to search via spotlight (not essential, but would be nice) Include searchable metadata information such as date, location, title Open-source or as low cost as possibly Allow simultaneous users to import files So far, I have looked at a few open source DAM, systems, such as Razuna, Gallery (not strictly DAM), ResourceSpace, Notre-DAM, while these are brilliant and open-source, they don't integrate as smoothly with the Desktop as iPhoto and aperture. For iPhoto and aperture, I have tried creating a Shared library on the server (a tad laggy), and also using a drive with no permissions, put a library and letting each client read from it, however if they want to put images onto the library only, it's only supports one user at a time writing to the library... Any ideas what could fulfill our needs? Or is it time to bite the bullet for FinalCut Server? Thanks in advance.

  Read the article

• Fixing partitions and Installing BackTrack

  - by Josh

  My whole problem started when I started trying to install Backtrack(3 or 4) Backtrack was trying to install itself over my entire windows partition (Which I had combined into one when I installed windows 7). So I booted back into windows 7 on my netbook (eee pc 1000 HE btw) I went into disk-manager with the aim of making a partition to install backtrack on but came out with a really screwed up drive. So I had two partions when I started: the windows system partition, and then my main partition and they were blue in diskmanager (I think that has something to do with formatting). After I went through the steps to make a 10 GB FAT32 partition for backtrack I had about five partitons one called PE: that I have no Idea what it is the windows system file, my main partiton 10 GB unallocated space, and two other partions under 50MB each that are both unused space. And they were all converted to simple volumes (Green instead of blue). And backtrack still wants to erase my entire drive. Question number 1: How do I get it back to the way it was? Question 2: How to I get backtrack to dual boot on my netbook?

  Read the article

• IIS 7.0 404 Custom Error Page and web.config

  - by Colin

  I am having trouble with a custom 404 error page. I have a domain running a .NET proj with it's own error handling. I have a web.config running for the domain which contains: <customErrors mode="RemoteOnly"> <error statusCode="500" redirect="/Error"/> <error statusCode="404" redirect="/404"/> </customErrors> On a sub dir of that domain I am ignoring all routes there by doing routes.IgnoreRoute("Assets/{*pathInfo}"); in the .NET proj and I want to put a custom 404 error page on that and any sub dir's of Assets. The sub dir contains static content like images, css, js etc etc. So in the Error Pages section of IIS I put a redirect to an absolute URL. The web.config for that dir looks like the following: <system.webServer> <httpErrors> <remove statusCode="404" subStatusCode="-1" /> <error statusCode="404" prefixLanguageFilePath="" path="http://mydomain.com/404" responseMode="Redirect" /> </httpErrors> </system.webServer> But I navigate to an unknown URL under that dir and yet I still see the default IIS 404 page. I am also seeing an alert in IIS that reads: You have configured detailed error messages to be returned for both local and remote requests. When this option is selected, custom error configuration is not used. Does this have anything to do with the customErrors mode="RemoteOnly" in the site web.config? I have tried to overwrite the customErrors in the sub dir web.config but nothing changes. Any help would be appreciated. Thanks.

  Read the article

• TicTac Photo and Windows 7

  - by Ben

  Hello, My wife has been creating a tictac photo album. I had to upgrade to windows 7 as i had enough of Vista so i backed up the tic tac photo file and the photos to an external hard disk and performed a fresh install of win7. Now here is the problem. TicTacPhoto says it can find the photos in the album. The locations were as follows: Vista: C:\Users\Kelly\Pictures Win 7 C:\Users\Kelly\My Pictures When i try to create a Pictures folder under Kelly it popups a message about merging the two folders and simply moves the pictures to the My Pictures folder. Does anyone know a way to make a foler called pictures so i can eliminate the file path problem and then try again with tic tac photo support to get them to fix my file. My wife is going to kill me as its our wedding album and she has spent upwards of 30hrs designing it and me upgrading to win 7 means its all my fault. She does not understand file paths etc. Im going to try and open the album file in a text editor and see if i can see anything but thought i would ask here as well. Any help appreciated.

  Read the article

• ZFS - Impact of L2ARC cache device failure (Nexenta)

  - by ewwhite

  I have an HP ProLiant DL380 G7 server running as a NexentaStor storage unit. The server has 36GB RAM, 2 LSI 9211-8i SAS controllers (no SAS expanders), 2 SAS system drives, 12 SAS data drives, a hot-spare disk, an Intel X25-M L2ARC cache and a DDRdrive PCI ZIL accelerator. This system serves NFS to multiple VMWare hosts. I also have about 90-100GB of deduplicated data on the array. I've had two incidents where performance tanked suddenly, leaving the VM guests and Nexenta SSH/Web consoles inaccessible and requiring a full reboot of the array to restore functionality. In both cases, it was the Intel X-25M L2ARC SSD that failed or was "offlined". NexentaStor failed to alert me on the cache failure, however the general ZFS FMA alert was visible on the (unresponsive) console screen. The zpool status output showed: pool: vol1 state: ONLINE scan: scrub repaired 0 in 0h57m with 0 errors on Sat May 21 05:57:27 2011 config: NAME STATE READ WRITE CKSUM vol1 ONLINE 0 0 0 mirror-0 ONLINE 0 0 0 c8t5000C50031B94409d0 ONLINE 0 0 0 c9t5000C50031BBFE25d0 ONLINE 0 0 0 mirror-1 ONLINE 0 0 0 c10t5000C50031D158FDd0 ONLINE 0 0 0 c11t5000C5002C823045d0 ONLINE 0 0 0 mirror-2 ONLINE 0 0 0 c12t5000C50031D91AD1d0 ONLINE 0 0 0 c2t5000C50031D911B9d0 ONLINE 0 0 0 mirror-3 ONLINE 0 0 0 c13t5000C50031BC293Dd0 ONLINE 0 0 0 c14t5000C50031BD208Dd0 ONLINE 0 0 0 mirror-4 ONLINE 0 0 0 c15t5000C50031BBF6F5d0 ONLINE 0 0 0 c16t5000C50031D8CFADd0 ONLINE 0 0 0 mirror-5 ONLINE 0 0 0 c17t5000C50031BC0E01d0 ONLINE 0 0 0 c18t5000C5002C7CCE41d0 ONLINE 0 0 0 logs c19t0d0 ONLINE 0 0 0 cache c6t5001517959467B45d0 FAULTED 2 542 0 too many errors spares c7t5000C50031CB43D9d0 AVAIL errors: No known data errors This did not trigger any alerts from within Nexenta. I was under the impression that an L2ARC failure would not impact the system. But in this case, it surely was the culprit. I've never seen any recommendations to RAID L2ARC. Removing the bad SSD entirely from the server got me back running, but I'm concerned about the impact of the device failure (and maybe the lack of notification from NexentaStor as well). Edit - What's the current best-choice SSD for L2ARC cache applications these days?

  Read the article

• Sparc v440 unable 2 boot after recommended patch install

  - by user100660

  After installing the October 2011 recommended patch bundle on a Solaris 10 the host fails to boot. The output is {0} ok boot SC Alert: Host System has Reset screen not found. keyboard not found. Keyboard not present. Using ttya for input and output. Sun Fire V440, No Keyboard Copyright 1998-2003 Sun Microsystems, Inc. All rights reserved. OpenBoot 4.10.10, 8192 MB memory installed, Serial #54744555. Ethernet address 0:3:ba:43:55:eb, Host ID: 834355eb. Rebooting with command: boot Boot device: /pci@1f,700000/scsi@2/disk@0,0:a File and args: \ Evaluating: Out of memory Warning: Fcode sequence resulted in a net stack depth change of 1 Evaluating: Evaluating: The file just loaded does not appear to be executable. {3} ok If I do a boot -F failsafe the host come up and I'm able to mount the root device (ufs on /dev/dsk/c1t0d0s0) and nothing appears broken, i.e I can see the logfiles from the patch install etc. Root device still have 1GB+ free. Only 2 kernel patches was installed from the patch bundle: 144500-19 & 147440-02. Any hints how to debug it further, etc.

  Read the article

• Leopard Network Shares and browsing are unreliable

  - by EvilChookie

  I have two macs, running Leopard 10.5.8. One is the 13" MBP connected via WiFi, and the other is a 24" 2008 iMac, connected via ethernet. There are at least another 6-10 machines (windows and mac) awake on the network (with shares) at any given time, yet there are plenty of times where I cannot see any devices/shares in either my "Shared" section in Finder, nor can I see any computers in "Network" in Finder. Restarting doesn't help. I've restarted all the networking gear in the house to no avail. Our network is a series of gigabit switches connected to a D-Link gaming router. I believe we use OpenDNS, and our provider is Cox. I hate having to use "Go - Connect to Server" to browse to commonly used file shares (by IP). I'd like to know why my shares do not always and consistently appear in Leopard. Edit: I ran OnyX this morning, and performed the cleaning and maintenance operations (including disk permissions) on both my Macs, and at least one of my macs has started showing network devices again. (the other is still going). No idea how long this will last. Any ideas as to what is causing this issue, and how to prevent it? Edit 2: Aaaand there the shares go again. So running OnyX is not a permanent or reliable fix for this issue. Edit 3: After a clean reinstall and update, network shares are still unreliable. The SMBClient command mentioned in comments shows me the information it's supposed to show, but the shares do not appear in the shared section. They'll also vanish at random and reappear at random throughout the day.

  Read the article

• Poor NFS Performance: OpenFiler

  - by Safin09

  Good Day Everyone, I have an issue with OpenFiler, a Linux-based operating that converts a computer system into a SAN/NAS appliance. Here is the problem. In my environment we have two Netapp Storevault 500 appliances that I normally perform backups to a NFS share. There are two backup cronjobs that use ghettoVCB to backup two groups of VM's. One group is a pool of 3 VMs. This takes 13 mins to complete. A second job that backups a pool of 5 VMs to a 2nd Storevault appliance which takes 2 hours. We then installed Openfiler on a old server that has 2 core Xeon processors. There is a software RAID 5 process in place. When performing the same backups to a NFS Openfiler share, the first backup job, which takes 13 mins, takes around 4 hours. The second backup job, which takes 2 hours, takes almost 10 hours to complete. This is unacceptable!!!! Especially considering the strain placed on the host ESX Server. I assumed that because of the software RAID 5, the overhead on the CPU explained the long backup times. I then installed Openfiler on a 2nd server, an IBM x306 machine which has a P4 Intel processor. This time no software RAID or any RAID at all. A single 750GB hard drive that contained the OS and the rest of the disk uses to backup VMs to a NFS share. I performed the first backup job of the pool of 3 VMs. This time the backup job took 1 and 1/2 hours to complete instead of 13 mins!!!!!!!!!! Is Openfiler simply poor at being an NFS Server!!!!!!!!!!!!! Has anyone else had these issues with Openfiler?

  Read the article

• Raid-1 Western Digital Green AARS, cloning and WD Align Utility

  - by Jaguar

  Hello all, My current setup runs on top of 2x Western Digital 2500KS drives on Raid-1, using the motherboard's 780G raid controller, on WinXP. Everything is fine, but the drives are a bit noisy. I am considering buying 2x WD6400AARS disks which are the 640GB slower 'green' drives, but also feature the Advanced Formatting 4KB sectors. This means that for WinXP the partition will have to be aligned to work properly, else there is a performance penalty. There are 2 questions here: The Green drives from WD are all slower and are (according to WD) susceptible to drop-out's from the controller. Has anyone any experience in this matter? Is there a possibility the controller will drop a drive? If so, can i do anything about it? Secondly, western digital gives a utility to perform the alignment on the partition. The thing is, will the utility see the drives in question as the operating system only sees 1 logical disk? I will be making the transition using a cloning tool (most probably norton ghost) unless i don't find a solution or a clear answer, in which case i'll just buy a win 7 license and make a clean install... thx in advance

  Read the article

• Need clear steps on how to convert a Windows 2000 Server to a XenServer VM

  - by Jay

  The source system is not local. The target host running XenServer is not local. The source system is running Windows 2000 Server SP4 and has 1 disk split into 6 partitions, all NTFS: C: 6 GB (boot) D: 15 GB E: 6 GB F: 6 GB G: 5 GB H: 26 GB Most of the partitions are mostly mostly full ( 60%). What is the most straightforward way to do a P2V migration of the server? I can do minor database & data syncs after the P2V is successful & running as a VM within XenServer, it's just getting to that point which is not clear. The option of installing a Windows 2000 Server from scratch is not available, I need to convert the existing physical server as-is into a VM to be hosted within a XenServer environment. I've looked at XenConvert but it maxes out on converting only 4 partitions in one shot, and I'm not certain how to account for the 2 extra partitions. I'm not familiar with XenServer but it's my only option right now to go P2V.

  Read the article

• Migrating to Amazon AWS etc: What key statistics/questions should be analyzed and asked?

  - by cerd

  I searched SOverflow pretty extensively for something similar to this set of questions. BACKGROUND: We are a growing 'big(ish)' data chemical data company that are outgrowing our lab and our dedicated production workhorses. Make no mistake, we need to do some serious query optimization. Our data (It comes from a certain govt. agency so the schema and lack of indexing is atrocious). So yes, I know, AWS or EC2 is not a silver bullet in the face of spending time to maybe rework your queries/code entirely 'out of the box'. With that said I would appreciate any input on the following questions: We produce on CentOS and lab on Ubuntu LTS which I prefer especially with their growing cloud / AWS integration. If we are mysql centric, and our biggest problem is these big cartesian products that produce slow queries, should we roll out what we know after more optimization with respect to Ubuntu/mySQL with the added Amazon horsepower? Or is there some merit to the NoSQL and other technologies they offer? What are the key metrics I need to gather from apache and mysql other than like: Disk I/O operations, Data up/down avgs and trends and special high usage periods/scenarios? I've reviewed AWS/EC2 fine print, but want 2nd opinions. What other services aside from the basic web/database have proven valuable to you? I know nothing of Hadoop or many other technologies they offer, echoing my prev. question, do you sometimes find it worth it (Initially having it be a gamble aside from basic homework) to dive/break into a whole new environment and try to/or end up finding a way of more efficiently producing your data/site product? Anything I should watch out for in projecting costs, or any other general advice when working with AWS folks from anyone else where your company is very niche and very very technical (Scientifically - or anybody for that matter)? Thanks very much for your input - I think this thread could be valuable to others as well.

  Read the article

• Increasing SQL Server / Sage performance with SSD? (Dell PE T410)

  - by Anthony

  I have a client wanting better performance of their Sage (Accpac & CRM) server (v5.5, soon to be v7). It's running on 1 of 2 Hyper-V VMs (Svr2008) on a Dell PE T410 server with 24GB of RAM (1333MHz) & dual quad-core, and both VMs (only their C: drives) are on a single RAID5 array. All clients connect via 1Gb ethernet. The 2nd VM is SBS2008 with 9GB RAM (& all SBS dbs & company data are on a separate RAID5 array), & 3GB RAM for the Svr2008 hypervisor. I've given the Sage/SQL Server VM all the RAM I can (12GB) & SQL Server RAM caching (~8GB, never exceeds ~7.5GB, eg. entire db can now be cached in RAM) and that's helped significantly. Upgrading the Hypervisor to Svr2012 is an obvious step, but probably not a dramatic improvement? What about an SSD for this Sage/SQL Server VM (VM = 100GB, <10GB for the actual live DB) ? Can SSDs be put into the SAS hot-swap bays? Or will I have to use the mobo SATA(3Gbps?) ports, or PCI-E SSD card? Should SSDs be RAIDed for this situation? Or is SSD's higher reliability offsetting the need for RAID1/5/10? (I have nightly full disk backups) New territory for me, would appreciate some feedback. Thanks, Anthony.

  Read the article

• Firefox isn't using my download manager (flash videos)

  - by John22

  I installed "Free Download Manager." I see the plugin in Tools-Add-ons (it doesn't have any options). I use several different flash video downloaders, because I haven't found one that works period on any site. When I save the video with two I tried, they are being downloaded by Firefox's default download manager (which means simultaneously - which is why I installed the download manager - I need them to download one at a time - in a prioritized queue.) [I used to use Flashgot (long ago), and it worked with some download manager I had installed - but over time it failed to see most videos. I installed Flashgot again, and it still fails to see anything but images and video ads.] Currently, I have to manually start Free Download Manager (from outside of Firefox), start the download in Firefox, stop it, copy the link location from Firefox's download menu, and then add it manually in Free Download Manager. Yuck. Do I need a different download manager (that takes over - recommendations?), or did I somehow install this one wrong or miss a setting somewhere in Firefox? Thanks for any help.

  Read the article

• Control Panel for MySQL and PostgreSQL server

  - by jfreak53

  I am looking for a control panel for a CentOS system that will allow me to add user's that can control their "own" MySQL and PostgreSQL Databases. I don't want to have to spend the $25 a month for cpanel on a dedicated to do this. Plus cPanel comes with all the rest like webserver and email that I don't need these to have. Basically I want to be able to create users that can create their own databases and only see those that they have created. I want to be able to control their disk space as with most panels. They need to be able to create their own DB users as well. Kloxo won't work as it doesn't natively support PostgreSQL. I tried straight PHPMyAdmin, but it won't let the user's create their own DB's unless they can also see everyone else's. VirtualMin I just can't get to work at all! ha ha I installed it an though it works great for itself if a user signs into Usermin they can see all DB's. If they sign into PHPMyAdmin (which basically means any program that directly connects to MySQL) they see all DB's. If they login to virtualmin then yes, they only see their's. But that won't work. I can't seem to think of another way to do this. I can use webmin and usermin directly but PHPMyAdmin again let's the user's I create either see only one DB and create none, or see all DB's. So that sound's like a permission problem in MySQL and PostgreSQL.

  Read the article

• Looking for a comprehensive/"expert" guide to BCD parameters

  - by Stilez

  I'm interested in educating myself about BCD on Windows 8. There are many, many "walkthrough" guides" and "howtos", but I can't find any guides at typical "enthusiast" level covering what each option or argument in a BCD /ENUM dump might mean, and the principles governing how these all work together. Imagine trying to rebuild or debug BCD (including EFI/BIOS variants and recovery/hibernate/memtest sections, and perhaps multiple boot Windows/WinPE/WinRE) from scratch using just BCDedit + DiskPart, and trying to understand rather than just copy/pasting commands. That's roughly the knowledge I'm after. Example questions might be: How is a BCD /ENUM dump to be read, item by item? How do its sections work together? (A lot of guides only show a specific example rather than explaining all the all common args that can exist and what they mean, they don't actually explain how sections work together, or they assume MBR/BIOS/Vista/7 and omit info needed for EFI/GPT/Dynamic disks/8) Partitions are specified by volume letter or as a \Device\HarddiskVolumeNNN. Why does it sometimes show these items as a letter and sometimes as a GUID? What are the practical differences if any? What exactly is syntax like "ramdisk=[C:]\Images\winpe.wim,{ramdiskoptions}" saying, and how will the drive letter "C" be interpreted at runtime in a line like this? Is the drive in such a line always "C:" (most examples assume so) and if not, when wouldn't it be? Many websites state that an sdi device and path may be needed in some sections of BCD, but what is sdi and what are these args doing when they appear? How does the GUID to HDD volume/partition mapping work under EFI/GPT? So that if disks or partitions/volumes change it's clear how one can confirm from basic principles whether data shown in BCD /ENUM ALL is still correct or not. Does anyone know of a suitable reference source for this kind of raw BCD data and structures? Thanks!

  Read the article

• Real-time local backup with versioning on Windows 7/8

  - by Borda

  I'm looking for a reliable backup solution on Windows, something with a feature set similar to Yadis. I've been using CrashPlan for 2 months, but their software lost more than 1TB of my data, that's why I'm looking for alternatives. Requirements: Real-time folder-to-folder backup: I don't need online features, I want to use this to duplicate my files between my local disks. Versioning support: Should be able to choose how many versions to keep of the files. Plain backup: I'd like to be able to open the backup without special software. No proprietary file format. External disk support: Shouldn't have any problem using external disks, at least on the source side. Backup every file, even locked/system files. (Yadis fails this one) Should start automatically, and have a comfortable GUI. Should use actively maintained and/or popular software. I don't want to use discontinued products. Optional requirements: Low RAM usage I'm not really comfortable with something that eats 1GB of my RAM. Compression support Preferably ZIP, but I'm not picky about this. Any ordinary everyday format is acceptable. Freeware or Open Source Preferred, but not necessary. I can do a one-time payment within reasonable bounds. (preferably under $100) I only need Windows support, but if it works on Linux, that's a plus. I've already searched and tried lots of software, most of them failed at the plain backup, the versioning or the locked file backup requirements.

  Read the article

• Drobo FS vs. MacBook Pro: Finder works, Drobo Dashboard doesn't

  - by dash-tom-bang

  Does anyone have any experience with the new Drobo FS, specifically using it from a MacBook Pro? My experience thus far is this: Set up the Drobo Dashboard software (hereinafter called simply 'Dashboard') on my WinXP machine, which is hard-wired to the network to do the data migration from my NAS-that's-being-replaced (a 250G SimpleShare which works well enough but I was always afraid of losing the one disk). The Dashboard seems to work ok, except that the DroboCopy function doesn't work at all. This is the backup solution, which I can configure, and if I launch it (e.g. to back up from the old NAS to the Drobo) it spins the NAS, seeking the drive all over hell and creation, until finally giving up an hour+ later with zero files copied. Selecting only a subset of the data yields the same effect albeit more quickly. On my Mac I installed the Dashboard software too, since most of my fiddling with the device will be from my couch in the living room. Finder connects to the box just fine, fwiw, but Dashboard just sits there, "waiting for connection." This is considerably more bothersome than the above paragraph, but I figured I'd give whatever information I have. Drobo is insisting that I send them this "Debug Log" file that their software generates. Does anyone know what's in it? It's encrypted and they won't tell me, which spooks me just a bit; not like I'm terribly concerned about privacy but I don't want to be sending personal information out to every clown who says they "need" it in order to help me. thanks a ton, -tom!

  Read the article

< Previous Page | 644 645 646 647 648 649 650 651 652 653 654 655  | Next Page >