Search Results

Search found 2823 results on 113 pages for 'crawl rate'.

Page 65/113 | < Previous Page | 61 62 63 64 65 66 67 68 69 70 71 72  | Next Page >

• how much more memcache memory do i need to get 95% hit ratio? [on hold]

  - by OneSolitaryNoob

  I have a memcache instance running that has a 90% hit ratio. How can I estimate how much more memory it needs to get to a 95% hit ratio? edit: This question was blocked, but I do not think this is impossible to answer. After all, anyone that's used a caching system HAS answered this question, most likely with trial&error&luck. I can look at my usage patterns. I can increase or decrease memory and see how hit rate changes. Both of these provide data that informs an estimate. But what's a good/better/best way to do this?

  Read the article

• SMB super slow within LAN between MAC and PC

  - by asdcasdc

  I have a windows desktop which stores all my movies, songs and pictures. I have a mac laptop which I would like to access these files. I don't want to utilize the FTP or SCP protocol because I don't want them to be downloaded to my mac. I want to access them as if they are a network mounted disk. So I tried using the native SMB protocol (available in Finder - Go - Connect to server). I tried dragging a file and dropping it onto my MAC's desktop. Surprisingly, I am only able to transfer at a very slow rate of about 1mb/s. Assuming network connectivity is not a problem, has anyone experienced incredible slowness with SMB? Are there alternative protocols for me to use in this case between PC and MAC?

  Read the article

• Horrible performing RAID

  - by Philip

  I have a small GlusterFS Cluster with two storage servers providing a replicated volume. Each server has 2 SAS disks for the OS and logs and 22 SATA disks for the actual data striped together as a RAID10 using MegaRAID SAS 9280-4i4e with this configuration: http://pastebin.com/2xj4401J Connected to this cluster are a few other servers with the native client running nginx to serve files stored on it in the order of 3-10MB. Right now a storage server has a outgoing bandwith of 300Mbit/s and the busy rate of the raid array is at 30-40%. There are also strange side-effects: Sometimes the io-latency skyrockets and there is no access possible on the raid for 10 seconds. The file system used is xfs and it has been tuned to match the raid stripe size. Does anyone have an idea what could be the reason for such a bad performing array? 22 Disks in a RAID10 should deliver way more throughput.

  Read the article

• European wireless data

  - by drewk

  I am on my way to Europe for 20 days with the wife and teenage kids. Among us, we have 3 iPhones, 1 Blackberry, 2 iPad 3G and 2 Macbook Pro laptops. Each has Skype. I am very concerned about AT&T data charges, and I am looking for a sensible alternative. For example, the AT&T data plans for the phones and iPads are $200 EACH for 200 MB per device. That is $1,200 and does not even cover the laptops. Ouch!!! I am thinking about a prepaid data plan from a European cell system of some sort combined with a GSM data modem and a Cradlepoint router, such as the CTR500. So, questions: 1) Anyone know of a GSM data source in Europe where I can buy a GSM Modem compatible with the CTR500 at a reasonable prepaid rate? 2) Experience with the CTR500?

  Read the article

• Googlebot DNS error HostPapa

  - by Gravy

  Received a message from Google Webmaster Tools: Over the last 24 hours, Googlebot encountered 2 errors while attempting to retrieve DNS information for your site. The overall error rate for DNS queries for your site is 40.0%. You can see more details about these errors in Webmaster Tools. Recommended action Contacted HostPapa and they deny that there is any issue with the site / server!!! Support in terms of what I can do to actually resolve this issue is non-existent!!!! The site is currently online. And I don't know much about DNS... so any advice about what I can do to resolve this problem would be much appreciated.

  Read the article

• How to measure Citrix receiver video buffer framerate?

  - by Rex Hardin

  How can I measure Citrix receiver framerate at the client end? I've tried FRAPS, but that doesn't seem to work. Is there a way to determine how many "frames" are sent per second from the client side? Assume a Windows 7 client connecting to a Windows 7 VM using the Citrix web plugin. To restate the question, how could I potentially measure the Citrix client's frame display rate for some 200px^2 area? Assume that the remote VM will try and play back a frame sequence at 24fps. Will any frames drop?

  Read the article

• FFMPEG Segfault Solutions

  - by Brentley_11

  I'm trying to convert a bunch of movies into h.264 mp4's using FFMPEG. These movies are sourced from various portable camcorders such as the Flip Mino HD and the Kodak ZI8. One issue I'm having with video from the ZI8 is it seems to be causing FFMPEG to segfault. Here is my command: ffmpeg -i 'XmasSailor720p60fps.MOV' -threads 2 -acodec libfaac -ab 96kb -vcodec libx264 -vpre hq -b 500kb -s 484x272 XmasSailor.mp4 Here is the output: FFmpeg version SVN-r20668, Copyright (c) 2000-2009 Fabrice Bellard, et al. built on Dec 2 2009 18:37:34 with gcc 4.2.4 (Ubuntu 4.2.4-1ubuntu4) configuration: --enable-libfaac --enable-libfaad --enable-libmp3lame --enable-libx264 --enable-gpl --enable-nonfree --enable-postproc --enable-pthreads --enable-shared libavutil 50. 5. 1 / 50. 5. 1 libavcodec 52.42. 0 / 52.42. 0 libavformat 52.39. 2 / 52.39. 2 libavdevice 52. 2. 0 / 52. 2. 0 libswscale 0. 7. 2 / 0. 7. 2 libpostproc 51. 2. 0 / 51. 2. 0 Seems stream 0 codec frame rate differs from container frame rate: 59.94 (60000/1001) -> 29.97 (30000/1001) Input #0, mov,mp4,m4a,3gp,3g2,mj2, from 'XmasSailor720p60fps.MOV': Duration: 00:00:05.37, start: 0.000000, bitrate: 12021 kb/s Stream #0.0(eng): Video: h264, yuv420p, 1280x720 [PAR 1:1 DAR 16:9], 11994 kb/s, 29.97 tbr, 90k tbn, 59.94 tbc Stream #0.1(eng): Audio: aac, 48000 Hz, stereo, s16, 128 kb/s Metadata major_brand : qt minor_version : 0 compatible_brands: qt comment : KODAK Zi8 Pocket Video Camera comment-eng : KODAK Zi8 Pocket Video Camera [libx264 @ 0x99e1020]using SAR=1/1 [libx264 @ 0x99e1020]using cpu capabilities: MMX2 SSE2Fast SSSE3 FastShuffle SSE4.1 Cache64 [libx264 @ 0x99e1020]profile High, level 2.1 Output #0, mp4, to 'XmasSailor.mp4': Stream #0.0(eng): Video: libx264, yuv420p, 484x272 [PAR 1:1 DAR 121:68], q=10-51, 500 kb/s, 30k tbn, 29.97 tbc Stream #0.1(eng): Audio: aac, 48000 Hz, stereo, s16, 96 kb/s Metadata comment : Encoded with the Statusfirm Video Transcoder Stream mapping: Stream #0.0 -> #0.0 Stream #0.1 -> #0.1 Press [q] to stop encoding [h264 @ 0x99de950]B picture before any references, skipping [h264 @ 0x99de950]decode_slice_header error [h264 @ 0x99de950]no frame! Error while decoding stream #0.0 [h264 @ 0x99de950]B picture before any references, skipping [h264 @ 0x99de950]decode_slice_header error [h264 @ 0x99de950]no frame! Error while decoding stream #0.0 frame= 20 fps= 0 q=13797729.0 size= 0kB time=0.66 bitrate= 0.6kbits/s frame= 39 fps= 37 q=13797729.0 size= 0kB time=1.30 bitrate= 0.3kbits/s frame= 48 fps= 30 q=33.0 size= 11kB time=0.10 bitrate= 903.0kbits/s frame= 58 fps= 27 q=31.0 size= 22kB time=0.43 bitrate= 421.0kbits/s frame= 67 fps= 25 q=29.0 size= 41kB time=0.73 bitrate= 462.6kbits/s frame= 75 fps= 23 q=29.0 size= 59kB time=1.00 bitrate= 486.7kbits/s frame= 83 fps= 22 q=29.0 size= 81kB time=1.27 bitrate= 521.9kbits/s frame= 90 fps= 21 q=29.0 size= 97kB time=1.50 bitrate= 530.1kbits/s frame= 98 fps= 20 q=29.0 size= 114kB time=1.77 bitrate= 526.9kbits/s frame= 106 fps= 20 q=29.0 size= 134kB time=2.04 bitrate= 537.7kbits/s frame= 114 fps= 19 q=29.0 size= 150kB time=2.30 bitrate= 533.7kbits/s frame= 122 fps= 19 q=29.0 size= 172kB time=2.57 bitrate= 547.8kbits/s frame= 130 fps= 19 q=29.0 size= 193kB time=2.84 bitrate= 557.5kbits/s frame= 136 fps= 18 q=29.0 size= 211kB time=3.04 bitrate= 570.0kbits/s frame= 144 fps= 18 q=29.0 size= 242kB time=3.30 bitrate= 599.5kbits/s frame= 152 fps= 17 q=30.0 size= 261kB time=3.57 bitrate= 598.6kbits/s frame= 157 fps= 15 q=-1.0 Lsize= 368kB time=5.21 bitrate= 579.3kbits/s video:302kB audio:61kB global headers:0kB muxing overhead 1.416371% [libx264 @ 0x99e1020]frame I:1 Avg QP:27.22 size: 8720 [libx264 @ 0x99e1020]frame P:48 Avg QP:25.15 size: 3759 [libx264 @ 0x99e1020]frame B:108 Avg QP:30.10 size: 1105 [libx264 @ 0x99e1020]consecutive B-frames: 0.6% 11.5% 28.8% 59.0% [libx264 @ 0x99e1020]mb I I16..4: 28.5% 47.6% 23.9% [libx264 @ 0x99e1020]mb P I16..4: 0.8% 1.3% 0.5% P16..4: 50.6% 17.7% 13.1% 0.0% 0.0% skip:15.9% [libx264 @ 0x99e1020]mb B I16..4: 0.2% 0.3% 0.1% B16..8: 44.0% 1.2% 2.6% direct: 5.1% skip:46.5% L0:45.5% L1:51.0% BI: 3.5% [libx264 @ 0x99e1020]final ratefactor: 23.51 [libx264 @ 0x99e1020]8x8 transform intra:49.9% inter:67.9% [libx264 @ 0x99e1020]direct mvs spatial:98.1% temporal:1.9% [libx264 @ 0x99e1020]coded y,uvDC,uvAC intra: 54.7% 76.1% 41.4% inter: 17.1% 24.4% 7.8% [libx264 @ 0x99e1020]i16 v,h,dc,p: 18% 52% 5% 25% [libx264 @ 0x99e1020]i8 v,h,dc,ddl,ddr,vr,hd,vl,hu: 12% 22% 9% 7% 10% 10% 9% 8% 13% [libx264 @ 0x99e1020]i4 v,h,dc,ddl,ddr,vr,hd,vl,hu: 13% 18% 8% 8% 10% 13% 10% 9% 12% [libx264 @ 0x99e1020]Weighted P-Frames: Y:10.4% [libx264 @ 0x99e1020]ref P L0: 60.2% 15.3% 11.0% 7.6% 5.2% 0.7% [libx264 @ 0x99e1020]ref B L0: 72.6% 15.6% 11.8% [libx264 @ 0x99e1020]kb/s:471.17 Segmentation fault I'm wondering if anyone else has ran into similar issues. I wasn't able to find anything helpful via Google. Another question I have is if anyone knows of a company that offers paid support for FFMPEG. Thank you for your time.

  Read the article

• Recommended RAM and disc space for Oracle 11g on Windows

  - by Álvaro G. Vicario

  I need to provide the recommended amount of RAM and disc space (divided in two partitions) so the customer can create an appropriate virtual machine to run Oracle. All I could find in the documentation was a brief listing with minimum RAM and typical/advanced install types. The virtual machine will run latest Oracle Standard Edition One (11g release 2 so far) under Windows Server 2008 x64 and will host a reasonably low traffic web application. How much RAM and disc must I ask for in order to be safe? (Feel free to ask for further details if I've omitted something relevant.) Update: Rough estimations: Database size: 10 MB after installation Growth rate: +3MB per day on average Size of database 'active' data: (not sure of what this means, there's not actual archive so I guess all data is current) Amount of data written per second in peak hours: a few KB Number of client sessions: 3 or 4 at most Frequency and response size of most heavy requests: some reports make heavy table JOINS that need up to 20 seconds to complete but they won't return more than a few thousand rows with plain text. The app also handles BLOBs (typical size from 50KB to 200KB)

  Read the article

• Exploratory Question for Security Admins (/etc/passwd + PHP)

  - by JPerkSter

  Hi everyone, I've been seeing a few issues lately on a few of my servers where an account gets hacked via outdated scripts, and the hacker uploads a cPanel / FTP Brute forcing PHP script inside the account. The PHP File reads /etc/passwd to get the usernames, and than uses a passwd.txt file to try and brute force it's way in to 127.0.0.1:2082. I'm trying to think of a way to block this. It doesn't POST anything except "GET /path/phpfile.php", so I can't use mod_security to block this. I've been thinking of maybe changing permissions on /etc/passwd to 600, however I'm unsure how this will result in regards to my users. I was also thinking of rate-limiting localhost connections to :2082, however I'm worried about mod_proxy being affected. Any suggestions?

  Read the article

• Very Large number of connections in TIME_WAIT state; Server is slow, ipconntrac

  - by Sparsh Gupta

  I have a nginx server with load balancing and reverse proxy. Right now its behing another nginx but very soon I plan to make it front, where it will receive TCP connections from clients directly at a rate of 500req/second I am having some big troubles with the server. I have pasted my configurations here and I am kinda sure that the problem is with ipconntrac and similar things which are alient to me http://paste.org/pastebin/view/28543 root@load_balancer:/proc/sys/net/ipv4# netstat -an|awk '/tcp/ {print $6}'|sort|uniq -c 67 CLOSING 727 ESTABLISHED 173 FIN_WAIT1 183 FIN_WAIT2 19 LAST_ACK 5 LISTEN 447 SYN_RECV 1 SYN_SENT 27970 TIME_WAIT Its a ubuntu machine with mainly nginx (load balancer and reverse proxy) installed. It surely isnt great. Can you help me understand whats going on and how can I fix it. This is my live server and I am sure its in a bad shape right now. Any document or commands to fix this, or settings I should make to make this better and reduce time wait and fin_wait1/2 better would be awesome.

  Read the article

• Can't communicate using PuTTY, but can with Termite

  - by SharpHawk

  I'm trying to establish a serial connection to a peripheral from my PC's RS-232 port. Pretty simple stuff, and I've had not trouble doing it with countless peripherals before. And yet when I configure PuTTY to the right baud rate, stop bits, etc. I'll type in "*IDN?", press enter, and the unit won't reply. After going over my settings over and over again, I decided to try another terminal program, Termite. This time it worked like a charm. What puzzles me, and what I'm trying to figure out by posting this question, is why Termite would work when PuTTY did not despite the fact that they both have the same settings. PuTTY: http://www.chiark.greenend.org.uk/~sgtatham/putty/download.html Termite: http://www.compuphase.com/software_termite.htm EDIT: I now tried Tera Term as well, and it works. So PuTTY is the odd one out.

  Read the article

• How to statically configure DNS servers on a Cisco router when the WAN interface uses DHCP?

  - by Massimo

  I have a Cisco router (model 887VA, IOS 15.4) used to connect a LAN to the Internet via ADSL. The WAN interface uses DHCP: interface ATM0.1 point-to-point ip address dhcp I need the router to use a statically-defined DNS server for name resolution: ip name-server A.B.C.D However, the router insists on using the DNS servers supplied by the ISP via DHCP: Router#ping www.google.com Translating "www.google.com"...domain server (<ISP DNS>) [OK] Type escape sequence to abort. Sending 5, 100-byte ICMP Echos to 173.194.116.208, timeout is 2 seconds: !!!!! Success rate is 100 percent (5/5), round-trip min/avg/max = 44/45/48 ms How can I tell the router to ignore the ISP-supplied DNS servers and only use the statically-configured one?

  Read the article

• Router's ssid changes from infrastructure to ad-hoc

  - by waldo

  For a period of time the router's ssid is shown (on various computers) as a normal infrastructure network - computers connect fine and everything works however after a few minutes / hours all computers see the same ssid as an ad-hoc network (not infrastructure). At this point a computer that was already connected continues to work - a computer that isn't cannot connect. Rebooting the router temporarily restores the visibility of the correct infrastructure ssid. Is something interfering? Connecting computers: macbook (2009), iphone 3g, windows vista desktop, windows xp desktop. Details: - D-Link DSL-2740B router set to WPA2-PSK (Personal) - Enable Wireless : Yes - Wireless Network Name (SSID) : ###### - Country : Australia - Wireless Channel : 1 - 802.11 Mode : Mixed 802.11n, 802.11g and 802.11b - Channel Width : Auto 20/40 MHz - Transmission Rate : Best (automatic) - Hide Wireless Network : No - Group Key Update Interval : 0 (seconds)

  Read the article

• Input not supported message when monitor is powered off then back on

  - by Jason Down

  I've been getting a message on my monitor where "Input not supported" is floating around. This only happens when I manually turn the monitor off and then later turn it back on. Leaving the monitor on and allowing it to go to the screen saver doesn't seem to cause the issue (but I prefer to turn the monitor off if I'm going to be away from the computer for any length of time). Any ideas what might cause this, only when the monitor is turned off manually? Specs: Acer X203w mointor Radeon 9600 Pro Video card Linux Mint 8 Resolution 1680 x 1050 (16:10 - Preferred native resolution for the monitor) Refresh Rate 60hz Here is what is in my xorg.conf file: Section "Device" Identifier "Radeon 9600" Driver "ati" BusID "PCI:1:0:0" Option "XAANoOffscreenPixmaps" Option "AccelMethod" "XAA" EndSection Section "Screen" Identifier "Default Screen" Device "Radeon 9600" DefaultDepth 24 SubSection "Display" Depth 24 Modes "1680x1050" "1440x900" "1024x768" EndSubSection EndSection Section "DRI" Mode 0666 EndSection Section "Extensions" Option "Composite" "Enable" EndSection

  Read the article

• traffic shaping for certain (local) users

  - by JMW

  Hello, i'm using ubuntu 10.10 i've a local backup user called "backup". :) i would like to give this user just a bandwidth of 1Mbit. No matter which software wants to connect to the network. this solution doesn't work: iptables -t mangle -A OUTPUT -p tcp -m owner --uid-owner 1001 -j MARK --set-mark 12 iptables -t mangle -A POSTROUTING -p tcp -m owner --uid-owner 1001 -j MARK --set-mark 12 tc qdisc del dev eth0 root tc qdisc add dev eth0 root handle 2 htb default 1 tc filter add dev eth0 parent 2: protocol ip pref 2 handle 50 fw classid 2:6 tc class add dev eth0 parent 2: classid 2:6 htb rate 10Kbit ceil 1Mbit tc qdisc show dev eth0 tc class show dev eth0 tc filter show dev eth0 does anyone know how to do it? thanks a lot in advance

  Read the article

• Mac OS Leopard: SyncServer process constantly using 100% CPU

  - by macca1

  I am running Leopard that I upgraded from Tiger. I've been noticing that every once in a while the SyncServer process starts up and eats up all the CPU. The fans will start going at full blast and the laptop will slow down to a crawl. I need to force quit the process from Activity Monitor to get it under control. It disappears for a while, but eventually gets started again. I do have an iphone as well that I sync so I'm wondering if syncServer might be an apple process checking for my phone plugged in. Edit: Tried iSync and the manual resetsync as suggested, but got this output: Vince-2:~ vince$ /System/Library/Frameworks/SyncServices.framework/Versions/A/Resources/resetsync.pl full 2010-03-12 08:03:50.230 perl[176:10b] SyncServer is unavailable: exception when connecting: connection timeout: did not receive reply PerlObjCBridge: NSException raised while sending reallyResetSyncData to NSObject object name: "ISyncServerUnavailableException" reason: "Can't connect to the sync server: NSPortTimeoutException: connection timeout: did not receive reply ((null))" userInfo: "" location: "/System/Library/Frameworks/SyncServices.framework/Versions/A/Resources/resetsync.pl line 16" ** PerlObjCBridge: dying due to NSException Vince-2:~ vince$ And during that syncServer started spinning up 95-100% just like it always does.

  Read the article

• How can I limit the upload/download bandwidth on my CentOS server?

  - by Dan Nestor

  How can I limit the upload and download bandwidth on my CentOS server? This is a box with a single interface, eth0. Ideally, I would like a command-line solution (I've been trying to use tc), something that I could easily switch on and off in a script. So far I've been trying to do something like tc filter add dev eth0 protocol ip prio 50 u32 police rate 100kbit burst 10240 drop but I'm obviously missing a lot of knowledge and information. Can somebody help with a quick one-liner? Many thanks, Dan

  Read the article

• Radeon HD 5770 - DisplayPort Problem

  - by Nick Schmit

  I am trying to set up 3 monitors with the Radeon HD 5770 I recieved a few days ago. I have read that I can use 2 DVI ports and an active DisplayPort adapter for a third DVI monitor. I have purchased this adapter: http://www.accellcables.com/products/DisplayPort/DP/dp_dvid.htm I have the two normal DVI monitors working, but when I try to extend the display to the third, I get a message saying the system has detected a problem with the connection through the display port which may limit resolution/refresh rate. I know that all the cables are fine, I have replaced the adapter, the monitors all work, I have tried different monitors through the adapter, and even nothing but the adapter, but I cannot get any monitor to work using it. I am trying to use 2 Dell monitors and an Acer. Have I overlooked something? Is there a compatibiliy issue I missed? Any suggestions as to what I could try? Thanks in advance.

  Read the article

• Server hard disk read speed and client download speed, is there a connection? [closed]

  - by Mywiki Witwiki

  Ok so a client's download speed is only as fast as a server's upload speed, and vice versa. Based on the answers to this post: Does upload speed depend upon download speed of the server? In other words, the data transfer rate between the two computers is only as fast as the speed of the "bottleneck". Let's pretend the two computers are in two different networks and both have 100Mbps internet connection. Ben wants a copy of a file in Mark's computer hard disk with 30Mbps read speed. Does this mean that Ben can download the file at a speed of around 30Mbps only, despite having an internet connection faster than 30Mbps?

  Read the article

• Should a sysadmin contractor charge overtime for off-peak hours?

  - by Jakobud

  This is not necessarily a server-related question, but more of a system admin question that I think would related to many on SF. I'm doing Sysadmin/IT consulting for a small company. I only work about 3 days a week for them on average. If a server goes down or something like that during off hours (nights, weekends, 3am, etc) and they need it fixed during those time periods, should I be charging overtime for that? I would I not be justified in charging overtime until I've logged 40 hours for the week? Perhaps calling it overtime isn't the best name. I guess maybe its better to call it an off-peak hourly rate. Anyways I just was curious what other consultants did in these circumstances.

  Read the article

• How can I share a video file during a webinar?

  - by Brien Malone

  Here is the scenario: I have a number of remote employees around the globe. I want to have a video chatting session. No problem there. Halfway through, I want to shut off all camera video feeds and simulcast (synchronous) a training video to my team. How do I do this? We have tried office communicator, but the frame rate was awful and no audio. Adobe Connect had similar trouble. In both cases we were limited by the main office's small internet pipe, but it is clear that video delivered by shared desktop is not a good solution.

  Read the article

• Sound entirely stopped working on Windows 8 on a Macbook Pro

  - by Kelvin Bongers

  I am currently running Windows 8 (downloaded from DreamSpark) on a Macbook Pro. This worked fine for a while but suddenly all audio stopped working. When I go to "Playback devices" and hit "Test" on the speakers I get treated with the following message: This also shows up right after I try restarting. I tried disallowing exclusive usage of the devices but it makes no difference. Edit: After some looking around I tried changing the sample rate and bit depth so I would get a dialog screen to force Windows to go around the program that's using it. I did get the dialog but then instead of changing it I got the following error: Edit 2: I narrowed it down to a single service failing to start, the Multimedia Class Scheduler service fails to start with the following error:

  Read the article

• PSAD Firewall/ UDP flood?

  - by Asad Moeen

  Well I'm actually trying to block a UDP Flood on the Application port because the string "getstatus" is causing my application to make large output due to a small input to the attacker's IP. I installed PSAD firewall to do the job. psad -S shows 3000,000 logged packets at the application port and top ports in Scan but does not block the IP of the attacker however other IP Addresses with small number of connections are dropped. I'm thinking that since output is also being made to the attacker, this is why its not getting blocked because iptables rate-limiting is also exactly doing the same thing and not blocking the IP where outgoing connection is also made. Any guesses why it won't work?

  Read the article

• How to make ssh/rsync/etc use a VLAN network interface?

  - by Annan

  A company I work for has a number of virtual servers with ElasticHosts. They are setup in such a way that eth1 is on a private VLAN connecting them to each other. This is so backups sent between servers are not charged at the same rate as external data transfer. My understanding of how VLANs and network interfaces work is sketchy at best. How can I make ssh, rsync, etc. transfer data through the VLAN? My final solution: I spent a while trying to figure this out, For all servers involved, edit /etc/sysconfig/network-scripts/ifcfg-eth1 DEVICE=eth1 BOOTPROTO=static ONBOOT=yes HWADDR=YOUR_MAC_ADDR IPADDR=192.168.0.100 NETMASK=255.255.255.0 Where HWADDR should already be set and the last octate of IPADDR should be different from each other. Then run, on all servers /etc/init.d/network restart After this the IP addresses specified by IPADDR can be used directly as any other IP address.

  Read the article

• multiple file systems for mysql

  - by RainDoctor

  Does mysql support multiple file systems for a single database with most of the tables being on MyISAM? Context: we have a 1.5TB mysql database, which is increasing at the rate of 200GB per month. The storage is directly attached, whose slots are almost full. I can add another DAS, and increase the file system. But resizing volume, resizing file system, etc are getting messy. Is there a concept of "tablespace, datafile" (like in oracle) in MySql world? Or how you guys manage mysql db with these kind of constraints?

  Read the article

< Previous Page | 61 62 63 64 65 66 67 68 69 70 71 72  | Next Page >