Search Results

Search found 17267 results on 691 pages for 'dynamic ip'.

Page 651/691 | < Previous Page | 647 648 649 650 651 652 653 654 655 656 657 658  | Next Page >

  • Routing with VPN and asymmetric communication

    - by Louis
    I'm stumbling on a problem that requires your advice. Keywords : networking, route, openVPN Problem : I have a local network with several physical servers and VMs. These machines have ip's in the range 10.10.x.x. I can access these machines from the Internet with the help of openVPN. These machines can : access each other within the local 10.10.x.x subnet access the Internet via the VPN can themselves be accessed (via SSH) from the Internet via the VPN. There is one machine however that behaves strangely and I don't know why. I can SSH into this machine from anywhere via SSH and I can also PING it from anywhere (including the Internet). However from this machine (i.e. when logged into it) I cannot access the Internet or ping machines outside the local network. In other words it will not go beyond the VPN. My question is why? Here are some technical details: The machine's Network Config (running Debian 6.0.3): allow-hotplug eth0 iface eth0 inet static address 10.10.10.200 netmask 255.255.0.0 network 10.10.10.0 broadcast 10.10.10.255 gateway 10.10.10.200 The machine's Routing : Destination Gateway Genmask Flags MSS Window irtt Iface 127.0.0.1 0.0.0.0 255.255.255.255 UH 0 0 0 lo 10.10.0.0 10.10.10.250 255.255.0.0 UG 0 0 0 eth0 10.10.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 10.10.10.250 0.0.0.0 UG 0 0 0 eth0 0.0.0.0 10.10.10.200 0.0.0.0 UG 0 0 0 eth0 The VPN's Network Config (running Debian 6.0.3): # This is the local network interface auto eth1 allow-hotplug eth1 iface eth1 inet static address 10.10.10.250 netmask 255.255.0.0 broadcast 10.10.10.255 gateway 10.10.10.250 The VPN's routing table Destination Gateway Genmask Flags MSS Window irtt Iface 10.10.0.0 0.0.0.0 255.255.255.0 U 0 0 0 tun0 private 0.0.0.0 255.255.255.0 U 0 0 0 eth0 10.10.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth1 0.0.0.0 10.10.10.250 0.0.0.0 UG 0 0 0 eth1 0.0.0.0 private 0.0.0.0 UG 0 0 0 eth0 net.ipv4.ip_forward = 1 on both machines. there are no iptables set anywhere. Thanks in advance for any feedback.

    Read the article

  • Wifi randomly drops on Windows 8 laptop

    - by JosiahS
    First of all, I did a lot of research on this problem, and I wasn't able to come to any helpful conclusion. I've finally decided that I need advice from those who might know where to look. So don't let me down. :P I used to have an older Windows 7 laptop, which worked great for basic office and web browsing. However, I wanted something that would play actual modern games. So I recently bought a Sager NP8235 with the Intel Wireless-AC 7260 wifi card, and installed Windows 8 Pro on it. And ever since, I've been having problems with the wifi. Generally, what happens is if I leave the laptop on but inactive for an extended amount of time (I've estimated it around an hour to two), the wifi will start dropping randomly. If I happened to have a download going at the time, it usually causes the download to fail. Or, if I put the laptop to sleep overnight, the next morning I usually have to restart the computer because the wifi device apparently stops working (it literally won't turn on). Also, and most frustrating, whenever I'm on a video chat (like Skype), after about ten minutes, the connection will start lagging like crazy, until it forces Skype to end the call. After that, I usually have to disable and reenable the wifi to get it working again. I know it isn't our internet, because all the other computers in our house (~8) don't have any issues. Even the old Windows 7 laptop (connected also over wifi) works just fine, scoring the normal ~3Mbps average on speedtest.net (yes, I know our internet is slow, we live out in the country). Additionally, when I connect the Sager directly to the router via ethernet, the internet instantly starts working just great. Like I said, I've done a lot of googling to figure out what's going on, and I haven't been able to find anything that worked for me. Is it Windows 8 conflicting with the Wifi drivers? As of this writing, I have the Intel drivers v16.1.5.2 installed (without the extra Intel software). Or is it our router? It's a TP-Link TL-WR841ND, set to the default settings. The Sager is currently being assigned to a static IP, if that makes any difference. And yet, the old windows 7 laptop has a much more stable connection than the Sager. Anyone have any ideas? At this point, I'd appreciate even knowing what the problem is.

    Read the article

  • MS DPM 2007: Testing the Recovery for a Production Domain

    - by NewToDPM
    Hi everybody! MS DPM 2007 is a new technology in my company, and so am I to the product. We have a classic Microsoft domain with two DCs, Exchange 2007 and a couple Web/MS SQL servers. I have deployed DPM one month ago on the domain, and after fixing the various issues I got with the replicas inconsistence and adapting the schedule and retention range to the server storage pool size, I can say the backup system is working correctly (no errors) as of today. However, there is one problem: we did not attempt to restore from the backups yet, which is a big no-no of course. I'm not sure about the way I should handle this, my main concern being Exchange and the System State of the DCs. From my understanding, DPM can only protect AND restore data on a server which is part of the same domain as the backup server. If I restore the System State (containing Active Directory) and the Exchange Storage Groups on a testing server, I am afraid it would completely disturb the domain functioning (for example, having two primary DCs on the domain). I am thinking about building a second DPM server on a testing separate domain which would mirror the replicas and then restore it on testing servers from this new domain. Is it the right way to handle the data recovery testing? How did you do on your domain when you first deployed DPM? I'd be grateful for any link/documentation or advice. Thank you in advance for your help! EDIT: Two options seem possible so far: i. Create another DC/Exchange server in the alternate location; ii. Create a separate domain in the alternate location and setup a trust between this domain and the production one. The option i is certainly the best but implies setting up a secondary Exchange server, with a dedicated public IP address so that if Exchange #1 dies, we can still send emails with Exchange #2. I don't know how complex this can be and would need to discuss it with my colleagues. The option ii would only fit the testing purposes. My only question regarding this is: if my production and DPM servers are part of domain A, and there is a trust between domains A and B, can I restore a domain A content to any domain B server?

    Read the article

  • Optimise Apache for EC2 micro instance

    - by Shiyu Sekam
    I'm running apache2 on a EC2 micro instance with ~600 mb RAM. The instance was running for almost a year without problems, but in the last weeks it just keeps crashing, because the server reached MaxClients. The server basically runs few websites, one wordpress blog(not often used), company website(most used) and 2 small sites, which are just internal. The database for the blog runs on RDS, so there's no Mysql running on this web server. When I came to the company, the server already was setup and is running apache + mod_php + prefork. We want to migrate that in the future to a nginx + php-fpm, but it still needs further testing. So for now I have to stick with the old setup. I also use CloudFlare DDOS protection in front of the server, because it was attacked a couple of the times in the last weeks. My company don't want to pay money for a better web server at this point, so I have to stick with the micro instance also. Additionally the code for the website we run is really bad and slow and sometimes a single page load can take up to 15 seconds. The whole website is dynamic and written in PHP, so caching isn't really an option here. It's a customized search for users. I've already turned off KeepAlive, which improved the performance a little bit. My prefork config looks like the following: StartServers 2 MinSpareServers 2 MaxSpareServers 5 ServerLimit 10 MaxClients 10 MaxRequestsPerChild 100 The server just becomes unresponsive after a while running and I've run the following command to see how many connections there are: netstat | grep http | wc -l 75 Trying to restart apache helps for a short moment, but after that a while the apache process(es) become unresponsive again. I've the following modules enabled(output of apache2ctl -M) Loaded Modules: core_module (static) log_config_module (static) logio_module (static) version_module (static) mpm_prefork_module (static) http_module (static) so_module (static) alias_module (shared) authz_host_module (shared) deflate_module (shared) dir_module (shared) expires_module (shared) mime_module (shared) negotiation_module (shared) php5_module (shared) rewrite_module (shared) setenvif_module (shared) ssl_module (shared) status_module (shared) Syntax OK apache2.conf # Security ServerTokens OS ServerSignature On TraceEnable On ServerName "web.example.com" ServerRoot "/etc/apache2" PidFile ${APACHE_PID_FILE} Timeout 30 KeepAlive off User www-data Group www-data AccessFileName .htaccess <Files ~ "^\.ht"> Order allow,deny Deny from all Satisfy all </Files> <Directory /> Options FollowSymLinks AllowOverride None </Directory> DefaultType none HostnameLookups Off ErrorLog /var/log/apache2/error.log LogLevel warn EnableSendfile On #Listen 80 Include /etc/apache2/mods-enabled/*.load Include /etc/apache2/mods-enabled/*.conf Include /etc/apache2/ports.conf LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %b" common LogFormat "%{Referer}i -> %U" referer LogFormat "%{User-agent}i" agent Include /etc/apache2/conf.d/*.conf Include /etc/apache2/sites-enabled/*.conf Vhost of main site <VirtualHost *:80> ServerName www.example.com ## Vhost docroot DocumentRoot /srv/www/jenkins/Web ## Directories, there should at least be a declaration for /srv/www/jenkins/Web <Directory /srv/www/jenkins/Web> AllowOverride All Order allow,deny Allow from all </Directory> ## Load additional static includes ## Logging ErrorLog /var/log/apache2/www.example.com.error.log LogLevel warn ServerSignature Off CustomLog /var/log/apache2/www.example.com.access.log combined ## Rewrite rules RewriteEngine On RewriteCond %{HTTP_HOST} !^www.example.com$ RewriteRule ^.*$ http://www.example.com%{REQUEST_URI} [R=301,L] ## Server aliases ServerAlias www.example.invalid ServerAlias example.com ## Custom fragment <Location /srv/www/jenkins/Web/library> Order Deny,Allow Deny from all </Location> <Files ~ "^\.(.+)"> Order deny,allow deny from all </Files> </VirtualHost>

    Read the article

  • Why does pinging a local router return "Destination Host Unreachable"?

    - by Matt H
    I have two tomato routers. One is bridged wirelessly with the other. I have a new server on the network. It's running Ubuntu Server 11.04. They are all connected like this: A - Linux PC B - New Server C - Mac Mini D - Macbook T1 - Tomato 1 T2 - Tomato 2 They are connected like so: A -----+-T1 ==== wireless bridge ==== T2----- ADSL modem | | C & D Connected wirelessly to T2 B -----+ A, C & D do not experience any issues. I have an active SSH session to B from A and it's not experiencing any loss. B, the new server occasionally cannot ping T2 and therefore cannot connect to the internet. However, A can always contact B and B can ping A and B When the network is lost, B can still ping T1, but not T2 yet at the same as B has lost connection to T2, A can still ping T2. Any ideas on what this could be? there is nothing that gives any clues in any of the logs on either router or the linux server. One thing that is interesting is that I set up a ping running between B and T2. T2 has the IP address 192.68.1.1 Here is what I am seeing: From 192.168.1.1 icmp_seq=26 Destination Host Unreachable From 192.168.1.1 icmp_seq=27 Destination Host Unreachable From 192.168.1.1 icmp_seq=28 Destination Host Unreachable From 192.168.1.1 icmp_seq=29 Destination Host Unreachable From 192.168.1.1 icmp_seq=30 Destination Host Unreachable From 192.168.1.1 icmp_seq=31 Destination Host Unreachable From 192.168.1.1 icmp_seq=33 Destination Host Unreachable From 192.168.1.1 icmp_seq=34 Destination Host Unreachable From 192.168.1.1 icmp_seq=35 Destination Host Unreachable 64 bytes from 192.168.1.1: icmp_req=36 ttl=63 time=3.40 ms 64 bytes from 192.168.1.1: icmp_req=37 ttl=63 time=5.70 ms 64 bytes from 192.168.1.1: icmp_req=38 ttl=63 time=2.25 ms 64 bytes from 192.168.1.1: icmp_req=39 ttl=63 time=2.18 ms 64 bytes from 192.168.1.1: icmp_req=40 ttl=63 time=3.12 ms 64 bytes from 192.168.1.1: icmp_req=41 ttl=63 time=2.15 ms 64 bytes from 192.168.1.1: icmp_req=42 ttl=63 time=1.97 ms 64 bytes from 192.168.1.1: icmp_req=43 ttl=63 time= And it cycles to being reachable and not. So I guess you could say the question is, why is the router responding that it cannot be reached?

    Read the article

  • Windows 7 & Virtual PC and Internet (gateway) problems on host PC

    - by Mufasa
    I upgraded to Windows 7 on a PC that is a few years old. The CPU was one revision away from having Hyper-V on it. So, I had to install Microsoft Virtual PC 2007 (v6.0.156.0) to run full XP instances instead of the seamless XP virtualization that is advertised so much. That's fine though; the 'older' version is useful since I use it to run different versions of the whole XP/IE stack for testing. (I'm a web developer.) ...And for the one 16-bit application we still use at the office for scheduling. * sigh * The virtual instances work fine, including networking. My issue is that after a reboot or coming out of sleep mode, my host Windows 7 won't connect to the Internet. It will connect to the local network fine. If I disable the "Virtual Machine Network Services" item (I'll call "VMNS" from here on) in the LAN Connection properties box, it starts working. But than the Virtual PC instances lose their network connectivity. If I re-enable VMNS again in the same instance, everything works (Internet on host and in the virtualized instances). But after the next reboot/sleep cycle this starts over. The route table gave me a clue though. When doing a cycle w/ VMNS enabled: IPv4 Route Table =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 On-link 10.0.3.51 20 0.0.0.0 0.0.0.0 10.0.10.10 10.0.3.51 276 ... After VMNS is disabled, the first route goes away. I assume that is for VMNS to intercept virtualized instance's network connections and forward them correctly? Just a guess though. More info: I checked my Firewall settings and Services (because I'm sort of a control nazi and turn off a lot) but couldn't find anything that made sense and if turned on changed anything. So it might be something there I'm missing, but I don't know what. My current hacked solution: So, I figured I'd mess with the routes myself to see if that helped, it did. If I run a route delete 0.0.0.0 on the universal (0.0.0.0) gateway routes, and add back in just the 2nd line with route add 0.0.0.0 mask 0.0.0.0 10.0.10.10--the one that points to my actual gateway (10.0.10.10)--then I don't have to mess with the disable/enable cycle of VMNS, and everything works. Running those two commands is faster then bringing up connection options and disabling and re-enabling VMNS, but I still don't want to have use that hack script every boot either. (Oh, and I also tried messing with hard-coding TCP/IP settings in my network adapter, including setting high metrics, etc., but that didn't help either.) Any suggestions on the right way to fix this?

    Read the article

  • MySQL won't start, reinstall fails on Ubuntu 12.04

    - by Evils
    My problem started yesterday night when I tried to change the my.cnf config on my ubuntu 12.04 x64 System. I simply tried to changed the bind-address parameter from 127.0.0.1 to 0.0.0.0. A simple restart after a reboot gave this error: stop: Unknown instance: start: Job failed to start I tried to start mysql then by using 'mysqld' which outputs this: 130701 11:05:59 [Note] Plugin 'FEDERATED' is disabled. mysqld: Table 'mysql.plugin' doesn't exist 130701 11:05:59 [ERROR] Can't open the mysql.plugin table. Please run mysql_upgrade to create it. 130701 11:05:59 InnoDB: The InnoDB memory heap is disabled 130701 11:05:59 InnoDB: Mutexes and rw_locks use GCC atomic builtins 130701 11:05:59 InnoDB: Compressed tables use zlib 1.2.3.4 130701 11:05:59 InnoDB: Initializing buffer pool, size = 128.0M 130701 11:05:59 InnoDB: Completed initialization of buffer pool 130701 11:05:59 InnoDB: highest supported file format is Barracuda. 130701 11:05:59 InnoDB: Waiting for the background threads to start 130701 11:06:00 InnoDB: 5.5.31 started; log sequence number 1595675 130701 11:06:00 [Note] Server hostname (bind-address): '127.0.0.1'; port: 3306 130701 11:06:00 [Note] - '127.0.0.1' resolves to '127.0.0.1'; 130701 11:06:00 [Note] Server socket created on IP: '127.0.0.1'. 130701 11:06:00 [ERROR] Can't start server : Bind on unix socket: Permission denied 130701 11:06:00 [ERROR] Do you already have another mysqld server running on socket: /var/run/mysqld/mysqld.sock ? 130701 11:06:00 [ERROR] Aborting 130701 11:06:00 InnoDB: Starting shutdown... 130701 11:06:00 InnoDB: Shutdown completed; log sequence number 1595675 130701 11:06:00 [Note] mysqld: Shutdown complete Meanwhile I already tried to reinstall and purge the complete mysql package which results in another error which says that dpkg cant change the admins password. While this error appeared another error came with it. When trying to install something new with apt, it always says 'fopen: permission denied' right after it tries to update my man-db. This is my dmesg output: [ 6879.687998] type=1400 audit(1372669683.397:36): apparmor="STATUS" operation="profile_replace" name="/usr/sbin/mysqld" pid=9336 comm="apparmor_parser" [ 6881.323215] init: mysql main process (9340) terminated with status 1 [ 6881.323316] init: mysql respawning too fast, stopped Any help will be appreciated as this is a productive server which renders useless without mysql.

    Read the article

  • Hyper-V Ubuntu Networking Problems Copying Large Amounts of Data

    - by Anonymous
    I am trying to copy a large amount (about 50 GB) of data over my network from a Hyper-V-hosted virtual machine running Ubuntu 11.04 (Natty Narwhal) to another (non-virtual) Ubuntu host that I plan to use for testing upgrades to one of our web applications. The problem I am having is with the virtual machine, which I shall refer to in what follows as "source.host". This machine is running 64-bit Ubuntu Server with the 2.6.38-8-server kernel and the Microsoft Linux Integration Components for Hyper-V kernel modules (hv_utils, hv_timesource, hv_netvsc, hv_blkvsc, hv_storvsc, and hv_vmbus) loaded. It uses a Hyper-V "synthetic network adapter" for its networking interface. To do the copy, I log on to the machine with the data and run the following commands (Call the remote machine "destination.host".): $ cd /path/to/data $ tar -cvf - datafolder/ | ssh [email protected] "cat > ~/data.tar" This runs for a while and then suddenly stops after transferring somewhere from 2-6 GB. The terminal on the source.host machine displays a Write failed: broken pipe error. The odd part is this: after this occurs, the "source.host" machine is no longer able to talk to the rest of the network. I cannot ping any other hosts on the network from the "source.host" machine, and I cannot ping the "source.host" machine from any other host on the network. I am equally unable to access the any of the web services hosted on "source.host". Running ifconfig on "source.host" shows the network adapter to be up and running as usual with the correct IP address and everything. I tried restarting the networking service with $ /etc/init.d/networking restart but the problem does not go away. Restarting the machine makes it capable of talking to the network again -- it can ping and be pinged by other hosts, and the web services are also accessible and usable as normal -- but attempting the copy operation again results in the same failure, requiring another restart. As an experiment, I tried replacing the tar -- ssh pipeline above with a straight scp: $ scp -r datafolder/ [email protected]:~ but to no avail Thinking that the issue might have to do with the kernel packet-send buffers filling up, I tried increasing the buffer size to 12 MB (up from the 128 KB default) with # echo 12582911 > /proc/sys/net/core/wmem_max but this also had no effect. I'm guessing at this point that it might be a problem with the Microsoft synthetic network driver, but I don't really know. Does anyone have any suggestions? Thank you very much in advance!

    Read the article

  • ntpdate works, but ntpd can't synchronize

    - by dafydd
    This is in RHEL 5.5. First, ntpdate to the remote host works: $ ntpdate XXX.YYY.4.21 24 Oct 16:01:17 ntpdate[5276]: adjust time server XXX.YYY.4.21 offset 0.027291 sec Second, here are the server lines in my /etc/ntp.conf. All restrict lines have been commented out for troubleshooting. server 127.127.1.0 server XXX.YYY.4.21 I execute service ntpd start and check with ntpq: $ ntpq ntpq> peer remote refid st t when poll reach delay offset jitter ============================================================================== *LOCAL(0) .LOCL. 5 l 36 64 377 0.000 0.000 0.001 timeserver.doma .LOCL. 1 u 39 128 377 0.489 51.261 58.975 ntpq> opeer remote local st t when poll reach delay offset disp ============================================================================== *LOCAL(0) 127.0.0.1 5 l 40 64 377 0.000 0.000 0.001 timeserver.doma XXX.YYY.22.169 1 u 43 128 377 0.489 51.261 58.975 XXX.YYY.22.169 is the address of the host I'm working on. A reverse lookup on the IP address in my ntp.conf file validates that the ntpq output is correctly naming the remote server. However, as you can see, it appears to just roll over to my .LOCL. time server. Also, ntptrace just returns the local time server, and ntptrace XXX.YYY.4.21 times out. $ ntptrace localhost.localdomain: stratum 6, offset 0.000000, synch distance 0.948181 $ ntptrace XXX.YYY.4.21 XXX.YYY.4.21: timed out, nothing received ***Request timed out This looks like my ntp daemon is just querying itself. I am thinking about the possibility that the router-I-don't-control between my test network timeserver and the corporate network timeserver is blocking on source port. (I think ntpdate sends on port 123, which gets it around that filter and is why I can't use it while ntpd is running.) I have email in to the network folks to check that. Finally, telnet XXX.YYY.4.21 123 never times out or completes a connection. The questions: What am I missing, here? What else can I check to try to figure out where this connection is failing? Would strace ntptrace XXX.YYY.4.21 show me the source port ntptrace is sending from? I can deconstruct most strace calls, but I can't figure out the location of that datum. If I can't directly examine the gateway router between my test network and the timeserver, how might I build evidence that it's responsible for these disconnections? Alternately, how might I rule it out?

    Read the article

  • Looking for a new, free firewall (Sunbelt has a huge hole)

    - by Jason
    I've been using Sunbelt Personal Firewall v. 4.5 (previously Kerio). I've discovered that blocking Firefox connections in the configuration doesn't stop EXISTING Firefox connections. (See my post here yesterday http://superuser.com/questions/132625/sunbelt-firewall-4-5-wont-block-firefox) The "stop all traffic" may work on existing connections - but I'm done testing, as I need to be able to be selective, at any time. I was using the free version, so the "web filtering" option quit working after some time (mostly blocking ads and popups), but I didn't use that anyway. I used the last free version of Kerio before finally having to go to Sunbelt, because Kerio had an unfixed bug where you'd eventually get the BSOD and have to reset Kerio's configuration and start over (configure everything again). So I'm looking for a new Firewall. I don't like ZoneAlarm at all (no offense to all it's users that may be here - personal taste). I need the following: (Sunbelt has all these, except *) - 1. Be able to block in/out to localhost (trusted)/internet selectively for each application with a click (so there's 4 click boxes for each application) [*that effects everything immediately, regardless of what's already connected]. When a new application attempts a connection, you get an allow/deny/remember windows. - 2. Be able to easily set up filter rules for 'individual application'/'all applications,' by protocol, port/address (range), local, remote, in, out. [*Adding a filter rule also doesn't block existing connections in Sunbelt. That needs to work too.] - 3. Have an easy-to-get-to way to "stop all traffic" (like a right click option on the running icon in the task bar). - 4. Be able to set trusted/internet in/out block/allowed (4 things per item) for each of IGMP, ping, DNS, DHCP, VPN, and broadcasts. - 5. Define locahost as trusted/untrusted, define adapter connections as trusted/untrusted. - 6. Block incoming connetions during boot-up and shutdown. - 7. Show existing connections, including local & remote ip/port, protocol, current speed, total bytes transferred, and local ports opened for Listening. - 8. An Intrusion Prevention System which blocks (optionally select each one) known intrustions (long list). - 9. Block/allow applications from starting other applications (deny/allow/remember window). Wish list: A way of knowing what svchost.exe is doing - who is actually using it/calling it. I allowed it for localhost, and selectively allowed it for internet each time the allow/deny window came up. Thanks for any help/suggestions. (I'm using Windows XP SP3.)

    Read the article

  • How to setup Proxy Cache with Nginx and Passenger

    - by tiny
    I use Nginx and Passenger for my rails application. I want to use proxy cache to cache my pages. However, every request go direct to my rails application. I don't know what wrong with my configuration. Below is my configuration: user www-data; worker_processes 1; events { worker_connections 1024; } http { passenger_root /usr/lib/ruby/gems/1.8/gems/passenger-2.2.15; passenger_ruby /usr/bin/ruby1.8; passenger_max_pool_size 6; passenger_max_instances_per_app 1; passenger_pool_idle_time 0; rails_spawn_method conservative; include mime.types; default_type application/octet-stream; server_names_hash_bucket_size 512; sendfile on; #tcp_nopush on; keepalive_timeout 65; tcp_nodelay on; gzip on; gzip_http_version 1.0; gzip_vary on; gzip_comp_level 6; gzip_proxied any; gzip_types text/plain text/css text/javascript application/javascript application/json application/x-javascript text/xml application/xml application/xml+rss; proxy_cache_path /var/www/cache/webapp levels=1:2 keys_zone=webapp:8m max_size=1000m inactive=600m; include vhosts/*.conf; include /opt/nginx/conf/sites-enabled/*; root /var/www; } server { listen 127.0.0.1:3008; server_name localhost; root /var/www/yoolk_web_app/public; # <--- be sure to point to 'public'! passenger_enabled on; rails_env development; passenger_use_global_queue on; } server { listen 80; server_name webpage.dev; proxy_set_header X-Real-IP $remote_addr; proxy_set_header Host $host; error_page 503 http://$host/maintenance.html; location ~* (css|js|png|jpe?g|gif|ico)$ { root /var/www/web_app/public; expires max; } location / { proxy_pass http://127.0.0.1:3008/; proxy_cache webapp; proxy_cache_valid 200 10m; } #More Location }

    Read the article

  • What would cause my SendMail server not to acknowledge receiving a TCP Sequence?

    - by Mike B
    My TCP/IP Stack knowledge is a little rusty so please bear with me.... I have a CentOS 5.7 server with SendMail and am having seeing intermittent timeout issues sending email (particularly larger email) to other remote domains. It doesn't happen with all attachments or recipient domains. Just some. After some extended troubleshooting, I think I've narrowed it down to TCP Sequences not being acknowledged. Here's a breakdown of the TCP session from a packet capture I collected directly on my MTA (fooMTA): Packet 1 - 11: Standard TCP handshake followed by initial SMTP conversation. No errors. Packet #12 Recipient MTA: TCP sequence 231. Ack 91. Packet #13 FooMTA: TCP sequence 91. Ack 305. Packet #14 FooMTA: TCP sequence 1115. Ack 305. Packet #15 Recipient MTA: TCP sequence 305. Ack 2495. Packet #16 FooMTA: TCP sequence 2495. Ack 305. Packet #17 FooMTA: TCP sequence 5255. Ack 305. Packet #18: Recipient MTA: TCP sequence 305. Ack 5255. Packet #19: FooMTA: TCP sequence 6635. Ack 305. Packet #20: FooMTA: TCP sequence 8015. Ack 305. Packet #21: Recipient MTA: TCP Sequence 305. Ack 8015. Packet #22: FooMTA: TCP Sequence 10775. Ack 305. Packet #23: FooMTA: TCP Sequence 13535. Ack 305. Packet #24: Recipient MTA: TCP sequence 305. Ack 10775 Packet #25: FooMTA: TCP Sequence 14915. Ack 305 It keeps going like this with my server still thinking it hasn’t received sequence 305… in response the remote side eventually retransmits its prior data thinking that it never arrived. Eventually the gap gets so large that no new data is sent and the remote MTA keeps retransmitting old stuff. This contributes to an exponential backoff and eventually the remote side gives up. What’s strange to me is that I see the “missing” TCP sequence (305 in this case) arriving back to my server (via a packet capture collected directly from fooMTA) So I don’t get why my server keeps asking for it. Could this be firewall related? What would be the next step in troubleshooting?

    Read the article

  • What else can I do to secure my Linux server?

    - by eric01
    I want to put a web application on my Linux server: I will first explain to you what the web app will do and then I will tell you what I did so far to secure my brand new Linux system. The app will be a classified ads website (like gumtree.co.uk) where users can sell their items, upload images, send to and receive emails from the admin. It will use SSL for some pages. I will need SSH. So far, what I did to secure my stock Ubuntu (latest version) is the following: NOTE: I probably did some things that will prevent the application from doing all its tasks, so please let me know of that. My machine's sole purpose will be hosting the website. (I put numbers as bullet points so you can refer to them more easily) 1) Firewall I installed Uncomplicated Firewall. Deny IN & OUT by default Rules: Allow IN & OUT: HTTP, IMAP, POP3, SMTP, SSH, UDP port 53 (DNS), UDP port 123 (SNTP), SSL, port 443 (the ones I didn't allow were FTP, NFS, Samba, VNC, CUPS) When I install MySQL & Apache, I will open up Port 3306 IN & OUT. 2) Secure the partition in /etc/fstab, I added the following line at the end: tmpfs /dev/shm tmpfs defaults,rw 0 0 Then in console: mount -o remount /dev/shm 3) Secure the kernel In the file /etc/sysctl.conf, there are a few different filters to uncomment. I didn't know which one was relevant to web app hosting. Which one should I activate? They are the following: A) Turn on Source Address Verification in all interfaces to prevent spoofing attacks B) Uncomment the next line to enable packet forwarding for IPv4 C) Uncomment the next line to enable packet forwarding for IPv6 D) Do no accept ICMP redirects (we are not a router) E) Accept ICMP redirects only for gateways listed in our default gateway list F) Do not send ICMP redirects G) Do not accept IP source route packets (we are not a router) H) Log Martian Packets 4) Configure the passwd file Replace "sh" by "false" for all accounts except user account and root. I also did it for the account called sshd. I am not sure whether it will prevent SSH connection (which I want to use) or if it's something else. 5) Configure the shadow file In the console: passwd -l to lock all accounts except user account. 6) Install rkhunter and chkrootkit 7) Install Bum Disabled those services: "High performance mail server", "unreadable (kerneloops)","unreadable (speech-dispatcher)","Restores DNS" (should this one stay on?) 8) Install Apparmor_profiles 9) Install clamav & freshclam (antivirus and update) What did I do wrong and what should I do more to secure this Linux machine? Thanks a lot in advance

    Read the article

  • Mac OSX 10.8 Server DNS Domain Routing

    - by Oldek
    I just cant seem to figure out the logic in how to configure my Mac Server. So I have set up an DNS, which will take the domain and all subdomains and point towards an IP. File: db.mydomain.com (in /var/named/) mydomain.com. 10800 IN SOA mydomain.com. admin.mydomain.com. ( 2012110903 ; serial 3600 ; refresh (1 hour) 900 ; retry (15 minutes) 1209600 ; expire (2 weeks) 86400 ; minimum (1 day) ) 10800 IN NS mydomain.com. 10800 IN A 10.0.1.2 www.mydomain.com. 10800 IN A 10.0.1.2 So I want all of these requests to be requested to the 10.0.1.2 server, as I run 2 servers in my cluster. This one has always handled the requests, and now I want to add a server in between. So the server in between will get all the signals from my router which NAT the trafic coming from outside. So after setting this up and trying to point my port 80 towards my new server which will be the middle point, it doesn't work. Is it even possible to do it this way? First server: Mac Second server: Linux So what I try to achieve once more: 1. User goes to mydomain.com or www.mydomain.com 2. User request gets handled by my first server 3. First server refers to a local server, which is only available locally (it is configured to allow requests on port 80 and handle them) 4. Second server receives signal 5. Second server returns a request (either directly send to user or send through first server, whichever is most secure and configurable) I also want to be able to set up domains that lead to other servers in the future, and some that are only available within the VPN. (If that changes anything) I hope some kind soul could help me with this, it is really cumbersome for my mind to get the logic here. Do I have to configure my other server in any way? /Marcus

    Read the article

  • Need help troubleshooting highly variable ping times

    - by Elliot.Bradshaw
    I'm at work using Citrix (think Remote Desktop) to connect to client sites. With my job I have to write a fair bit of code while I'm connected remotely via Citrix, so the latency of my internet connection is important. If I'm getting ping times above 250ms, then it becomes almost impossible to scroll, click or type with accuracy. Recently my Comcast business internet has been exhibiting highly variable ping times. If I ping google.com, I'll get pings that range from 9ms all the way up to 1300ms. The problem seems to be at its worst during the hours of 1PM to 4:30PM. Outside of those hours and the variance in pings settles down, mostly between 9ms and 50ms. The signal to noise ratio and upstream power are both fine on my modem--the values are here: http://pastebin.com/D4hWGPXf I ran a trace route from my computer to google.com (the results of which are here: http://pastebin.com/GcdjYvMh) and did another test ping to the IP of the first hop outside of our local network (73.98.44.1)--the variance in ping times existed in exactly the same manner as if I were pinging Google. Connecting directly to the cable modem by CAT5 makes no difference. Here is a screenshot demonstrating the variance of the ping times: http://postimage.org/image/haocdeauv/full/ -- as you can see it can get pretty bad. Three Comcast techs have been out (two of them were here when the problem wasn't happening) and they as well as the regional tier 2 Comcast support were unable to diagnose the problem. I now have a ticket open with tier 3 support, but have yet to hear back from them. Does anyone know what could cause these sorts of problems or have any idea from the traceroute above where it could be originating? The regional tier 2 guy tried to tell me that what I'm seeing is normal--are highly variable ping times like that ever acceptable? Anything I should ask Comcast to do or look at to get this problem fixed? Any tips/advice much appreciated! Edit: This is Comcast cable internet at a small start-up, we've ruled out congestion in our private LAN as a cause (i.e., no one's watching YouTube when the pings become variable). Update: Tier 3 Comcast support advised swapping out the modem, a tech came here today and did that--same problem persists.

    Read the article

  • Serving protected files using Nginx's X-Accel-Redirect header

    - by andybak
    I'm trying to serve protected files using this directive in my nginx.conf: location /secure/ { internal; alias /home/ldr/webapps/nginx/app/secure/; } I'm passing in paths in the form: "/myfile.doc" and the file's path would be: /home/ldr/webapps/nginx/app/secure/myfile.doc I just get 404's when I access "http: //myserver/secure/myfile.doc" (space inserted after http to stop ServerFault converting it to a link) I've tried taking the trailing / off the location directive and that makes no difference. Two questions: How do I fix it! How can I debug problems like this myself? How can I get Nginx to report which path it's looking for? error.log shows nothing and access.log just tells me which url is being requested - this is the bit I already know! It's no fun trying things randomly without any feedback. Here's my entire nginx.conf: daemon off; worker_processes 2; events { worker_connections 1024; } http { include mime.types; default_type application/octet-stream; server { listen 21534; server_name my.server.com; client_max_body_size 5m; location /media/ { alias /home/ldr/webapps/nginx/app/media/; } location / { proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; fastcgi_pass unix:/home/ldr/webapps/nginx/app/myproject/django.sock; fastcgi_pass_header Authorization; fastcgi_hide_header X-Accel-Redirect; fastcgi_hide_header X-Sendfile; fastcgi_intercept_errors off; include fastcgi_params; } location /secure { internal; alias /home/ldr/webapps/nginx/app/secure/; } } } EDIT: I'm trying some of the suggestions here So I've tried: location /secure/ { internal; alias /home/ldr/webapps/nginx/app/; } both with and without the trailing slash on location. I've also tried moving this block before the "location /" directive. The page I linked to has ^~ after 'location' giving: location ^~ /secure/ { ...etc... Not sure what that signifies but it didn't work either!

    Read the article

  • Nginx Load Balancer 403 error

    - by user64473
    I am trying to install nginx as a load balancer with apache backends, so that when I point my sites to the nginx server it serves up the content from the apache backend. I have the apache configuration set up correctly on both (i.e when I go to the site on the apache servers it works great) but when I use the nginx load balancer as the site I get 403 error. I have no idea why as it isn't even accessing any files on the server, thusly there aren't any files to be forbidden access to. My virtual host is enabled and looks like this: upstream webs { server 10.0.0.30 weight=1; server 10.0.0.31 weight=1; } server { listen 80; server_name www.example.com example.com; access_log /var/log/nginx/access.log; location / { proxy_pass http://webs; include /etc/nginx/proxy.conf; } } and my nginx.conf looks like this: user www-data; worker_processes 4; error_log /var/log/nginx/error.log; pid /var/run/nginx.pid; events { worker_connections 1024; # multi_accept on; } http { include /etc/nginx/mime.types; access_log /var/log/nginx/access.log; sendfile on; #tcp_nopush on; #keepalive_timeout 0; keepalive_timeout 65; tcp_nodelay on; gzip on; gzip_disable "MSIE [1-6]\.(?!.*SV1)"; include /etc/nginx/conf.d/*.conf; include /etc/nginx/sites-enabled/*; proxy_redirect off; proxy_set_header Host $host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; client_max_body_size 10m; client_body_buffer_size 128k; proxy_connect_timeout 90; proxy_send_timeout 90; proxy_read_timeout 90; proxy_buffers 32 4k; } Can any geniuses out there tell me what I am doing wrong?

    Read the article

  • Why can't we reach some (but not all) external web service via VPN connection?

    - by Paul Haldane
    At work (UK university) we use a set of Windows servers running WS2008R2 and RRAS which offer VPN service to students in our accommodation. We do this to associate the network connections with individuals. Before they've connected to the VPN all they can talk to is the stuff thats needed to setup the VPN and a local web site with documentation on how to connect. Medium term we'll probably replace this but it's what we're using at the moment. VPN on the 2008 servers allocates client a private (10.x) address. Access to external sites is through NAT on the campus routers (same as any other directly connected client on a private address). Non-VPN connections aren't seeing this problem. Older servers run WS 2003 and ISA2004. That setup works but has become unreliable under load. Big difference there was that we were allocating non-RFC1918 addresses to the clients (so no NAT required). Behaviour we're seeing is that once connected to the VPN, clients can reach local web sites (that is sites on the campus network) but only some external sites. It seems (but this may be chance) that the sites we can reach are Google ones (including YouTube). We certainly have trouble reaching Microsoft's Office 365 service (which is a pain because that's where mail for most of our students is). One odd bit of behaviour is that clients can fetch (using wget on a Windows 7 client) http://www.oracle.com/ (which gets a 301 redirect) but hangs when asked to fetch http://www.oracle.com/index.html (which is what the first URL redirects to). Access works reliably if we configure clients to use our local web proxies (Squid). My gut tells me that this is likely to be something in the chain dropping replies either based on HTTP inspection or the IP address in the reply. However I'm puzzled about why we're seeing this with the VPN clients. Plan for tomorrow (when I'm back in the office) is to setup a web server on external connection so that we can monitor behaviour at both ends of the conversation (hoping that the problem manifests itself with our test server). Any suggestions for things we should be looking at?

    Read the article

  • Nginx config - serving index.html not working

    - by Bill
    I can't figure out how to redirect / to index.html. I've gone through the threads on serverfault and I think I've tried every suggestion including: rewrite statements within location / index index.html at the server level, within location / and within static content moving node.js proxy statements to location ~ /i instead of within location / Obviously something is wrong somewhere else in my configuration. Here is my nginx.conf: worker_processes 1; pid /home/logs/nginx.pid; events { worker_connections 1024; } http { include mime.types; default_type application/octet-stream; sendfile on; keepalive_timeout 65; error_log /home/logs/error.log; access_log /home/logs/access.log combined; include sites-enabled/*; } and my server config located in sites-enabled server { root /home/www/public; listen 80; server_name localhost; # proxy request to node location / { index index.html index.htm; proxy_set_header Host $http_host; proxy_set_header X-Real-IP $remote_addr; proxy_set_header X-Forwarded-For $proxy_add_x_forwarded_for; proxy_set_header X-NginX-Proxy true; proxy_pass http://127.0.0.1:3010; proxy_redirect off; break; } # static content location ~ \.(?:ico|jpe?g|jpeg|gif|css|png|js|swf|xml|woff|eot|svg|ttf|html)$ { access_log off; add_header Pragma public; add_header Cache-Control public; expires 30d; } gzip on; gzip_vary on; gzip_http_version 1.0; gzip_comp_level 2; gzip_proxied any; gzip_min_length 1000; gzip_disable "msie6"; gzip_types text/plain text/css application/json application/x-javascript text/xml application/xml application/xml+rss text/javascript; } Everything else is working just fine. Requests get proxied to node correctly and static content is served correctly. I just need to be able to forward requests made to / to /index.html.

    Read the article

  • unable to connect site to different port

    - by JohnMerlino
    I have a domain was registered at godaddy named http://mysite.com/. I logged into godaddy and I went to All Products Domains Domain Management. I clicked on the appropriate domain and it took me to the Domain Details page. I clicked Launch under DNS Manager and it took me to the Zone File Editor. I noticed that notify.mysite.com was pointing to an IP address pointing to a dead server, so I switched it to an operating server. Then I pinged the domain to see where it was pointing to and it was correctly pointing to the working server. So I copied the default configuration under sites-available: sudo cp default notify.mysite.com. And then I made some edits to it to have it point to a different document root to serve files at a different port: Listen 1740 Listen 64.135.xx.xxx:1740 #I also tried this as well: NameVirtualHost 64.135.xx.xxx:1740 <VirtualHost 64.135.xx.xxx:1740> ServerAdmin [email protected] ServerName notify.mysite.com DocumentRoot /var/www/test/public <Directory /var/www/test/public> Order allow,deny allow from all </Directory> ErrorLog ${APACHE_LOG_DIR}/error.log LogLevel warn CustomLog ${APACHE_LOG_DIR}/access.log combined </VirtualHost> Then I enabled the virtual host. Then I went to the document root and added an index.html file with some text in it. Then I restarted apache. The restart gave no errors. Then I type the correct domain in URL: http://notify.mysite.com:1740/ and I get: Oops! Google Chrome could not connect to notify.mysite.com:1740 Somehow it took out all my other sites. Now even the ones that were responding on port 80 are no longe responding, even though I did not touch the virtual hosts for them. I get this message now: Oops! Google Chrome could not connect to mysite.com However, ping responds: ping mysite.com PING mysite.com (64.135.12.134): 56 data bytes 64 bytes from 64.135.12.134: icmp_seq=0 ttl=49 time=20.839 ms 64 bytes from 64.135.12.134: icmp_seq=1 ttl=49 time=20.489 ms The result of telnet: $ telnet guarddoggps.com 80 Trying 64.135.12.134... telnet: connect to address 64.135.12.134: Connection refused telnet: Unable to connect to remote host

    Read the article

  • [CentOS 4.8] nslookup resolves domains to IPs, but I can't get a response to pings to external servers

    - by Beco
    I have a fresh install of CentOS 4.8 running on an internal development server. I haven't done anything to it besides setting up sudoers and SSH. I can SSH into the server and from there resolve domains to IPs and ping internal servers, but for some reason I don't get any response from pinging external servers. The software firewall is disabled, and the problem is present with both static and DHCP-assigned network configurations. The network domain controller is a Windows Server 2003 box. $ nslookup google.com Server: 10.254.2.5 Address: 10.254.2.5#53 Non-authoritative answer: Name: google.com Address: 74.125.47.147 Name: google.com Address: 74.125.47.99 <etc...> 10.254.2.5 is the Win2K3 server. $ ping google.com PING google.com (74.125.47.106) 56(84) bytes of data. It just hangs here indefinitely. $ cat /etc/resolv.conf ; generated by /sbin/dhclient-script search <...snip...>.local nameserver 10.254.2.5 nameserver 10.254.2.124 10.254.2.124 is the backup DC server, which is currently off and tombstoned by this point. The snipped section is our company name. # ifconfig eth0 Link encap:Ethernet HWaddr <snip> inet addr:10.254.2.101 Bcast:10.254.2.255 Mask:255.255.255.0 inet6 addr: <snip>/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:80066 errors:0 dropped:0 overruns:0 frame:0 TX packets:4421 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:7810133 (7.4 MiB) TX bytes:590550 (576.7 KiB) Interrupt:225 Base address:0xc000 lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:32 errors:0 dropped:0 overruns:0 frame:0 TX packets:32 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:8104 (7.9 KiB) TX bytes:8104 (7.9 KiB) # route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 10.254.2.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth0 0.0.0.0 10.254.2.5 0.0.0.0 UG 0 0 0 eth0 And, for good measure, a snapshot of the current ethernet config via the system-config-network GUI. Edit: I don't yet have enough rep to post images, so here's a link. Sorry! system-config-network snapshot I'm pretty green when it comes to setting up *nix dev servers and network configuration in general, so please let me know if I've left out critical information, or posted information I shouldn't have posted. Thanks!

    Read the article

  • Primefaces tabview: set the active index on tab change

    - by Virgi
    I've got a tab view that contains two tab. When I switch from tab 1 to tab 2, I'm calling some code that executes a validation and updates some values. Depending on the result of this validation, I would like to stay on tab 1, or go to tab 2, and refresh the tabs' content. My tabview: <h:form id="form"> <p:tabView id="tabview" activeIndex="#{ctrl.idx}" dynamic="true" cache="false"> <p:ajax event="tabChange" listener="#{ctrl.doStuff}" update=":form:tabview"/> <p:tab title="Tab 1" id="t1"> <h:panelGrid columns="1" cellpadding="10"> <h:outputText value="#{ctrl.s1}"/> </h:panelGrid> </p:tab> <p:tab title="Tab 2" id="t2"> <h:panelGrid columns="1" cellpadding="10"> <h:outputText value="#{ctrl.s2}"/> </h:panelGrid> </p:tab> </p:tabView> </h:form> My test code that simly changes the values: public void doStuff() { s1 = String.valueOf(Math.random()); s2 = String.valueOf(Math.random()); } I thought that changing the active tab index in my method would be enough, like that: public void doStuff() { // ... idx = 0; } On tabChange event, the method is called but the tabview components goes to the clicked tab, ignoring the idx new value. I thought adding an update attribute to p:ajax would render the whole tabview but only the tabs and/or the tabs' content is re rendered. And weirdest of all, if I change update=":form:tabview" to update=":form" or update="@form", I only receive the tab's content in the ajax response - the component disappears from the page! My bean is viewscoped, I'm using Primefaces 3.5, JSF 2.1 and Tomcat 7. Any idea? Thanks.

    Read the article

  • Android RelativeLayout fill_parent unexpected behavior in a ListView with varying row heights

    - by Jameel Al-Aziz
    I'm currently working on a small update to a project and I'm having an issue with Relative_Layout and fill_parent in a list view. I'm trying to insert a divider between two sections in each row, much like the divider in the call log of the default dialer. I checked out the Android source code to see how they did it, but I encountered a problem when replicating their solution. To start, here is my row item layout: <?xml version="1.0" encoding="utf-8"?> <RelativeLayout android:id="@+id/RelativeLayout01" android:layout_width="fill_parent" xmlns:android="http://schemas.android.com/apk/res/android" android:padding="10dip" android:layout_height="fill_parent" android:maxHeight="64dip" android:minHeight="?android:attr/listPreferredItemHeight"> <ImageView android:id="@+id/infoimage" android:layout_width="wrap_content" android:layout_height="wrap_content" android:clickable="true" android:src="@drawable/info_icon_big" android:layout_alignParentRight="true" android:layout_centerVertical="true"/> <View android:id="@+id/divider" android:background="@drawable/divider_vertical_dark" android:layout_marginLeft="11dip" android:layout_toLeftOf="@+id/infoimage" android:layout_width="1px" android:layout_height="fill_parent" android:layout_marginTop="5dip" android:layout_marginBottom="5dip" android:layout_marginRight="4dip"/> <TextView android:id="@+id/TextView01" android:textAppearance="?android:attr/textAppearanceLarge" android:layout_width="wrap_content" android:layout_height="wrap_content" android:layout_centerVertical="true" android:layout_toRightOf="@+id/ImageView01" android:layout_toLeftOf="@+id/divider" android:gravity="left|center_vertical" android:layout_marginLeft="4dip" android:layout_marginRight="4dip"/> <ImageView android:id="@+id/ImageView01" android:layout_width="wrap_content" android:layout_height="wrap_content" android:layout_alignParentLeft="true" android:background="@drawable/bborder" android:layout_centerVertical="true"/> </RelativeLayout> The issue I'm facing is that each row has a thumbnail of varying height (ImageView01). If I set the RelativeLayout's layout_height property to fill_parent, the divider does not scale vertically to fill the row (it just remains a 1px dot). If I set layout_height to "?android:attr/listPreferredItemHeight", the divider fills the row, but the thumbnails shrink. I've done some debugging in the getView() method of the adapter, and it seems that the divider's height is not being set properly once the row has it's proper height. Here is a portion of the getView() method: public View getView(int position, View view, ViewGroup parent) { if (view == null) { view = inflater.inflate(R.layout.tag_list_item, parent, false); } The rest of the method simply sets the appropriate text and images for the row. Also, I create the inflater object in the adapter's constructor with: inflater = LayoutInflater.from(context); Am I missing something essential? Or does fill_parent just not work with dynamic heights?

    Read the article

  • AddHandler not working?

    - by EdenMachine
    I can't figure out why my addhandler is not firing? In the Sub "CreateTagStyle" thd AddHandler is to firing when the LinkButton is clicked Is there some reason that addhandlers can't be adding at certain points of the page lifecycle? <%@ Page Title="" Language="VB" MasterPageFile="~/_Common/Admin.master" %> <script runat="server"> Protected Sub Page_Load(ByVal sender As Object, ByVal e As System.EventArgs) End Sub Protected Sub RadGrid1_NeedDataSource(ByVal source As Object, ByVal e As Telerik.Web.UI.GridNeedDataSourceEventArgs) If Not e.IsFromDetailTable Then Dim forms As New MB.RequestFormPacket() RadGrid1.DataSource = forms.GetPackets() End If End Sub Protected Sub RadGrid1_DetailTableDataBind(ByVal source As Object, ByVal e As Telerik.Web.UI.GridDetailTableDataBindEventArgs) Select Case e.DetailTableView.Name Case "gtvForms" Dim PacketID As Guid = e.DetailTableView.ParentItem.GetDataKeyValue("ID") e.DetailTableView.DataSource = MB.RequestForm.GetRequestForms(PacketID) End Select End Sub Protected Sub RadGrid1_InsertCommand(ByVal source As Object, ByVal e As Telerik.Web.UI.GridCommandEventArgs) If IsValid Then Select Case TryCast(e.Item.NamingContainer.NamingContainer, GridTableView).Name Case "gtvPackets" Dim rtbName As RadTextBox = TryCast(e.Item.FindControl("rtbName"), RadTextBox) Dim IsActive As Boolean = TryCast(e.Item.FindControl("cbxIsActive"), CheckBox).Checked Dim packet As New MB.RequestFormPacket() packet.Name = rtbName.Text packet.IsActive = IsActive packet.Insert() e.Canceled = True e.Item.OwnerTableView.IsItemInserted = False RadGrid1.Rebind() System.Web.UI.ScriptManager.RegisterStartupScript(Me.Page, Me.GetType(), "ClientMessage", "SuccessMessage('Request Form Packet has been added successfully.');", True) Case "gtvForms" Dim parentItem As GridDataItem = e.Item.OwnerTableView.ParentItem Dim rcbForms As RadComboBox = TryCast(e.Item.FindControl("rcbForms"), RadComboBox) Dim rf As New MB.RequestForm() rf.RequestFormPacketID = CType(parentItem.OwnerTableView.DataKeyValues(parentItem.ItemIndex)("ID"), Guid) rf.FormID = rcbForms.SelectedValue If MB.RequestFormPacket.HasItems(rf.RequestFormPacketID) Then rf.SortOrder = rf.MaxSortOrder + 1 Else rf.SortOrder = 0 End If rf.Insert() e.Canceled = True e.Item.OwnerTableView.IsItemInserted = False TryCast(e.Item.NamingContainer.NamingContainer, GridTableView).Rebind() End Select End If End Sub Protected Sub RadGrid1_UpdateCommand(ByVal source As Object, ByVal e As Telerik.Web.UI.GridCommandEventArgs) If IsValid Then Select Case TryCast(e.Item.NamingContainer, GridTableView).Name Case "gtvPackets" Dim PacketID As Guid = CType(CType(e.CommandSource, Button).NamingContainer, GridEditFormItem).GetDataKeyValue("ID") Dim Name As String = TryCast(e.Item.FindControl("rtbName"), RadTextBox).Text Dim Tags As String = TryCast(e.Item.FindControl("hdnTags"), HiddenField).Value Dim IsActive As Boolean = TryCast(e.Item.FindControl("cbxIsActive"), CheckBox).Checked Dim rfp As New MB.RequestFormPacket() rfp.Update(PacketID, Name, IsActive) Call MB.RequestFormPacketTag.Insert(PacketID, Tags) e.Item.Edit = False TryCast(e.Item.NamingContainer, GridTableView).Rebind() System.Web.UI.ScriptManager.RegisterStartupScript(Me.Page, Me.GetType(), "ClientMessage", "SuccessMessage('Request Form Packet has been updated successfully.');", True) Case "gtvForms" Dim RequestFormID As Guid = CType(CType(e.CommandSource, Button).NamingContainer, GridEditFormItem).GetDataKeyValue("ID") Dim rcbForms As RadComboBox = TryCast(e.Item.FindControl("rcbForms"), RadComboBox) Dim rf As New MB.RequestForm() rf.Update(RequestFormID, rcbForms.SelectedValue) e.Item.Edit = False TryCast(e.Item.NamingContainer, GridTableView).Rebind() End Select End If End Sub Protected Sub RadGrid1_DeleteCommand(ByVal source As Object, ByVal e As Telerik.Web.UI.GridCommandEventArgs) Dim editedItem As GridEditableItem = TryCast(e.Item, GridEditableItem) Select Case CType(editedItem.Parent.Parent, GridTableView).Name Case "gtvPackets" Dim ID As Guid = CType(CType(e.CommandSource, ImageButton).NamingContainer, GridDataItem).GetDataKeyValue("ID") MB.RequestFormPacket.Delete(ID) System.Web.UI.ScriptManager.RegisterStartupScript(Me.Page, Me.GetType(), "ClientMessage", "NotifyMessage('Request Form Packet has been deleted.');", True) Case "gtvForms" Dim ID As Guid = CType(CType(e.CommandSource, ImageButton).NamingContainer, GridDataItem).GetDataKeyValue("ID") MB.RequestForm.Delete(ID) System.Web.UI.ScriptManager.RegisterStartupScript(Me.Page, Me.GetType(), "ClientMessage", "NotifyMessage('Request Form has been removed.');", True) End Select End Sub Protected Sub ibnItemUpArrow_Command(ByVal sender As Object, ByVal e As System.Web.UI.WebControls.CommandEventArgs) Dim gtv As GridTableView = CType(CType(sender, ImageButton).NamingContainer.NamingContainer, GridTableView) Dim ID As Guid = New Guid(e.CommandArgument.ToString()) Call MB.RequestForm.MoveUp(ID) gtv.Rebind() End Sub Protected Sub ibnItemDownArrow_Command(ByVal sender As Object, ByVal e As System.Web.UI.WebControls.CommandEventArgs) Dim gtv As GridTableView = CType(CType(sender, ImageButton).NamingContainer.NamingContainer, GridTableView) Dim ID As Guid = New Guid(e.CommandArgument.ToString()) Call MB.RequestForm.MoveDown(ID) gtv.Rebind() End Sub Protected Sub RadGrid1_RowDrop(ByVal sender As Object, ByVal e As Telerik.Web.UI.GridDragDropEventArgs) If String.IsNullOrEmpty(e.HtmlElement) Then If e.DraggedItems(0).OwnerGridID = RadGrid1.ClientID Then If e.DestDataItem IsNot Nothing Then Dim gtv As GridTableView = CType(e.DestDataItem.NamingContainer, GridTableView) For Each gdi As GridDataItem In e.DraggedItems Select Case gtv.Name Case "gtvForms" MB.RequestForm.DragAndDropReorder(gdi.GetDataKeyValue("ID"), e.DestDataItem.GetDataKeyValue("ID"), IIf(e.DropPosition = GridItemDropPosition.Above, True, False)) gtv.Rebind() End Select Next End If End If End If End Sub Protected Sub cbxAllowDragAndDrop_CheckedChanged(ByVal sender As Object, ByVal e As System.EventArgs) Dim cbx As CheckBox = CType(sender, CheckBox) If cbx.Checked Then RadGrid1.ClientSettings.AllowRowsDragDrop = True RadGrid1.ClientSettings.Selecting.AllowRowSelect = True RadGrid1.ClientSettings.Selecting.EnableDragToSelectRows = True Else RadGrid1.ClientSettings.AllowRowsDragDrop = False RadGrid1.ClientSettings.Selecting.AllowRowSelect = False RadGrid1.ClientSettings.Selecting.EnableDragToSelectRows = False End If End Sub Protected Sub ibnDisableToggleProcess_Click(ByVal sender As Object, ByVal e As System.Web.UI.ImageClickEventArgs) Dim ibn As ImageButton = CType(sender, ImageButton) Dim hdn As HiddenField = CType(ibn.NamingContainer.FindControl("hdnDisableProcessID"), HiddenField) Dim status As Boolean = MB.RequestFormPacket.ActivateToggle(New Guid(hdn.Value)) Dim gtv As GridTableView = CType(ibn.NamingContainer.NamingContainer, GridTableView) gtv.Rebind() System.Web.UI.ScriptManager.RegisterStartupScript(Me.Page, Me.GetType(), "ClientMessage", "SuccessMessage('Process has been " & IIf(status, "Activated", "Deactivated") & ".');", True) End Sub Protected Function DisplayTagList(ByVal tags As IEnumerable(Of MB.RequestFormPacketTag)) As String Dim list As String = "" For Each t As MB.RequestFormPacketTag In tags list += "<span class=""tags"">" & t.Tag.Name & "</span>" Next Return list End Function Protected Sub RadGrid1_ItemDataBound(ByVal sender As Object, ByVal e As Telerik.Web.UI.GridItemEventArgs) Select Case e.Item.GetType.Name Case "GridEditFormInsertItem" 'do nothing Case "GridEditFormItem" Dim plh As PlaceHolder = CType(e.Item.FindControl("plhTags"), PlaceHolder) Dim hdn As HiddenField = CType(e.Item.FindControl("hdnTags"), HiddenField) If hdn IsNot Nothing Then Dim gefi As GridEditFormItem = e.Item Dim packet As MB.RequestFormPacket = gefi.DataItem For Each pt As MB.RequestFormPacketTag In packet.RequestFormPacketTags Call CreateTagStyle(plh, hdn, pt.Tag.Name) If hdn.Value = "" Then hdn.Value = "|" End If hdn.Value += pt.Tag.Name & "|" Next End If End Select End Sub Protected Sub btnAddTag_Click(ByVal sender As Object, ByVal e As System.EventArgs) Dim btnAddTag As Button = sender Dim rtbTags As RadTextBox = btnAddTag.NamingContainer.FindControl("rtbTags") Dim plhTags As PlaceHolder = btnAddTag.NamingContainer.FindControl("plhTags") Dim hdnTags As HiddenField = btnAddTag.NamingContainer.FindControl("hdnTags") Dim TagExists As Boolean = False rtbTags.Text = rtbTags.Text.ToUpper().Trim() Dim currentTags() As String = Split(hdnTags.Value, "|") For i As Integer = 1 To currentTags.Count - 2 Call CreateTagStyle(plhTags, hdnTags, currentTags(i)) Next If TagExists = False And String.IsNullOrEmpty(rtbTags.Text) = False Then Call CreateTagStyle(plhTags, hdnTags, rtbTags.Text) If String.IsNullOrEmpty(hdnTags.Value) Then hdnTags.Value = "|" End If hdnTags.Value += rtbTags.Text & "|" 'System.Web.UI.ScriptManager.RegisterStartupScript(Me.Page, Me.GetType(), "ClientMessage", "highlightTag('" & lbn.ClientID & "');", True) End If rtbTags.Text = "" rtbTags.Focus() End Sub Public Sub RemoveTag(ByVal sender As Object, ByVal e As EventArgs) Response.End() Dim lbnSender As LinkButton = sender Dim plhTags As PlaceHolder = lbnSender.NamingContainer.FindControl("plhTags") Dim hdnTags As HiddenField = lbnSender.NamingContainer.FindControl("hdnTags") Response.Write(hdnTags.Value) Response.End() Dim TagExists As Boolean = False Dim currentTags() As String = Split(hdnTags.Value, "|") For i As Integer = 1 To currentTags.Count - 2 Call CreateTagStyle(plhTags, hdnTags, currentTags(i)) Next End Sub Protected Sub CreateTagStyle(ByVal plh As PlaceHolder, ByVal hdn As HiddenField, ByVal tagName As String) Dim lbn As New LinkButton() lbn.ID = "lbn_" & hdn.ClientID & "_" & tagName lbn.CssClass = "deleteCreateTag" lbn.Text = "X" AddHandler lbn.Click, AddressOf RemoveTag plh.Controls.Add(New LiteralControl("<div><span class=showTag>" & tagName & "</span>")) plh.Controls.Add(lbn) plh.Controls.Add(New LiteralControl("</div>")) End Sub </script> <asp:Content ID="Content1" ContentPlaceHolderID="head" Runat="Server"> <style type="text/css"> .tags { border:solid 1px #93AFE5; background-color:#F3F7F8; margin: 0px 2px 0px 2px; padding: 0px 4px 0px 4px; font-family:Verdana; font-size:10px; text-transform:uppercase; } </style> <script type="text/javascript"> function highlightTag(id) { $("#" + id).highlightFade({ color: '#FFFF99', speed: 2000, iterator: 'sinusoidal' }); } </script> </asp:Content> <asp:Content ID="Content2" ContentPlaceHolderID="ContentPlaceHolder1" Runat="Server"> <telerik:RadAjaxManager ID="RadAjaxManager1" runat="server" DefaultLoadingPanelID="RadAjaxLoadingPanel1" EnableAJAX="false"> <AjaxSettings> <telerik:AjaxSetting AjaxControlID="RadGrid1"> <UpdatedControls> <telerik:AjaxUpdatedControl ControlID="RadGrid1" /> </UpdatedControls> </telerik:AjaxSetting> </AjaxSettings> </telerik:RadAjaxManager> <telerik:RadAjaxLoadingPanel ID="RadAjaxLoadingPanel1" runat="server" /> <telerik:RadTabStrip ID="RadTabStrip1" runat="server" Skin="WebBlue" style="position:relative;top:1px;" ValidationGroup="vgTabs"> <Tabs> <telerik:RadTab Text="Request Form Packets" Selected="true" ImageUrl="~/Admin/Images/Packet2.png" /> <telerik:RadTab Text="Request Forms" NavigateUrl="Forms.aspx" ImageUrl="~/Admin/Images/Forms.png" /> </Tabs> </telerik:RadTabStrip> <asp:ObjectDataSource ID="odsForms" runat="server" TypeName="MB.Form" SelectMethod="GetForms" /> <asp:Panel ID="pnlContent" runat="server" CssClass="ContentPanel"> <telerik:RadGrid ID="RadGrid1" runat="server" AllowPaging="True" AllowSorting="True" GridLines="None" OnNeedDataSource="RadGrid1_NeedDataSource" AllowAutomaticUpdates="true" AllowAutomaticDeletes="true" AllowAutomaticInserts="true" OnInsertCommand="RadGrid1_InsertCommand" OnUpdateCommand="RadGrid1_UpdateCommand" OnDeleteCommand="RadGrid1_DeleteCommand" OnRowDrop="RadGrid1_RowDrop" OnDetailTableDataBind="RadGrid1_DetailTableDataBind" OnItemDataBound="RadGrid1_ItemDataBound"> <%-----------------------------------------------------------%> <%------------------------- PACKETS -------------------------%> <%-----------------------------------------------------------%> <MasterTableView AutoGenerateColumns="False" DataKeyNames="ID" ClientDataKeyNames="ID" ShowHeadersWhenNoRecords="true" Name="gtvPackets" NoMasterRecordsText="There are currently no Request Form Packets" GroupLoadMode="Client" RetrieveNullAsDBNull="true" CommandItemDisplay="Top" AllowAutomaticUpdates="true" AllowAutomaticDeletes="true" AllowAutomaticInserts="true"> <RowIndicatorColumn> <HeaderStyle Width="20px"></HeaderStyle> </RowIndicatorColumn> <ExpandCollapseColumn> <HeaderStyle Width="20px"></HeaderStyle> </ExpandCollapseColumn> <CommandItemTemplate> <table width="100%"> <tr> <td class="AdminGridHeader">&nbsp;<img src="../Admin/Images/Packet2.png" align="absmiddle" width="16" height="16" />&nbsp;&nbsp;Request Form Packets</td> <td width="1%"><asp:CheckBox ID="cbxAllowDragAndDrop" runat="server" AutoPostBack="true" OnCheckedChanged="cbxAllowDragAndDrop_CheckedChanged" /></td> <td width="1%" nowrap="nowrap"><asp:Label AssociatedControlID="cbxAllowDragAndDrop" ID="Label1" runat="server" Text="Enable Drag and Drop Reordering" ToolTip="Drag and Drop Reordering applies only to Forms." /></td> <td align="right" width="1%"><asp:Button ID="btnAddPacket" Text="Create New Packet" runat="server" CommandName="InitInsert" /></td> </tr> </table> </CommandItemTemplate> <EditFormSettings> <EditColumn ButtonType="PushButton" HeaderStyle-Font-Bold="true" UniqueName="EditCommandColumn" /> </EditFormSettings> <EditItemStyle Font-Bold="true" BackColor="#FFFFCC" /> <Columns> <telerik:GridTemplateColumn HeaderText="Packet Name" UniqueName="PacketName" SortExpression="Name"> <ItemTemplate> <img src="../Admin/Images/Packet2.png" align="absmiddle" width="16" height="16" />&nbsp;&nbsp;<%#Eval("Name")%> </ItemTemplate> <EditItemTemplate> <telerik:RadTextBox runat="server" ID="rtbName" Width="300" Text='<%# Bind("Name") %>' /> <asp:RequiredFieldValidator ID="rfvName" runat="server" ErrorMessage="Required" ControlToValidate="rtbName" /> </EditItemTemplate> </telerik:GridTemplateColumn> <telerik:GridTemplateColumn HeaderText="Tags" UniqueName="Tags"> <ItemTemplate> <%#DisplayTagList(Eval("RequestFormPacketTags"))%> </ItemTemplate> <EditItemTemplate> <asp:Panel ID="pnlAddTags" runat="server" DefaultButton="btnAddTag"> <table cellpadding="0" cellspacing="0"> <tr> <td> <telerik:RadTextBox ID="rtbTags" runat="server" Width="200" style="text-transform:uppercase;" /> <asp:RegularExpressionValidator ID="revTags" runat="server" ErrorMessage="Invalid Entry" ControlToValidate="rtbTags" Display="Dynamic" ValidationExpression="^[^<>`~!/@\#}$%:;)(_^{&*=|+]+$" ValidationGroup="vgTags" /> </td> <td> <asp:Button ID="btnAddTag" runat="server" ValidationGroup="vgTags" Text="Add" OnClick="btnAddTag_Click" /> </td> </tr> </table> </asp:Panel> <div id="divTags"> <asp:PlaceHolder id="plhTags" runat="server" /> <asp:HiddenField ID="hdnTags" runat="server" /> </div> </EditItemTemplate> </telerik:GridTemplateColumn> <telerik:GridTemplateColumn HeaderTooltip="Disable" ItemStyle-Width="1%" ItemStyle-HorizontalAlign="Center" SortExpression="IsActive" UniqueName="IsActive" ReadOnly="true"> <ItemTemplate> <asp:ImageButton ID="ibnDisabledProcess" runat="server" ImageUrl="../Images/Icons/Stop.png" Width="16" OnClientClick="return window.confirm('Activate this Process?');" ToolTip="Click to activate this Request for Account use." Visible='<%#IIF(Eval("IsActive"),false,true) %>' OnClick="ibnDisableToggleProcess_Click" /> <asp:ImageButton ID="ibnEnabledProcess" runat="server" ImageUrl="../Images/Icons/Stop_disabled.png" Width="16" OnClientClick="return window.confirm('Deactivate this Process?');" ToolTip="Click to deactivate this Request for Account use." Visible='<%#IIF(Eval("IsActive"),true,false) %>' OnClick="ibnDisableToggleProcess_Click" /> <asp:HiddenField ID="hdnDisableProcessID" runat="server" Value='<%#Eval("ID") %>' /> </ItemTemplate> </telerik:GridTemplateColumn> <telerik:GridTemplateColumn HeaderText="Is Active" UniqueName="IsActiveCheckbox" Display="false"> <EditItemTemplate> <asp:CheckBox ID="cbxIsActive" runat="server" Checked='<%# IIF(Eval("IsActive") Is DbNull.Value OrElse Eval("IsActive") = False,False,True) %>' /> </EditItemTemplate> </telerik:GridTemplateColumn> <telerik:GridEditCommandColumn ButtonType="ImageButton" EditText="Edit Admin" ItemStyle-Width="16" EditImageUrl="~/Images/edit-small.png" /> <telerik:GridButtonColumn ConfirmText="Do you really want to delete this Admin? WARNING: THIS CANNOT BE UNDONE!!" ConfirmDialogType="RadWindow" ConfirmTitle="Delete" ButtonType="ImageButton" CommandName="Delete" Text="Delete Admin" ImageUrl="~/Images/Delete.png" UniqueName="DeleteColumn"> <ItemStyle HorizontalAlign="Center" Width="16" /> </telerik:GridButtonColumn> </Columns> <DetailTables> <%-----------------------------------------------------------%> <%-------------------------- FORMS --------------------------%> <%-----------------------------------------------------------%> <telerik:GridTableView Name="gtvForms" AllowPaging="true" PagerStyle-Position="TopAndBottom" PageSize="20" AutoGenerateColumns="false" DataKeyNames="RequestFormPacketID,ID" runat="server" CommandItemDisplay="Top" Width="100%"> <ParentTableRelation> <telerik:GridRelationFields DetailKeyField="RequestFormPacketID" MasterKeyField="ID" /> </ParentTableRelation> <CommandItemTemplate> <table width="100%" class="AdminGridHeaders"> <tr> <td class="AdminGridHeaders"> &nbsp;<img src="../Admin/Images/Forms.png" align="absmiddle" width="16" height="16" />&nbsp;&nbsp;Forms </td> <td align="right"> <asp:Button ID="ibnAdd" runat="server" Text="Add Form" CommandName="InitInsert" /> </td> </tr> </table> </CommandItemTemplate> <EditFormSettings> <EditColumn ButtonType="PushButton" InsertText="Save" UpdateText="Update" CancelText="Cancel" /> </EditFormSettings> <EditItemStyle Font-Bold="true" BackColor="#FFFFCC" /> <Columns> <telerik:GridTemplateColumn HeaderText="Form Name" UniqueName="FormName"> <ItemTemplate> <img src="../Admin/Images/Forms.png" align="absmiddle" width="16" height="16" style="margin-right:4px;" /> <%#Eval("Form.Name")%> </ItemTemplate> <EditItemTemplate> <telerik:RadComboBox ID="rcbForms" runat="server" DataSourceID="odsForms" AppendDataBoundItems="true" DataTextField="Name" DataValueField="ID" SelectedValue='<%#Bind("FormID")%>'> <Items> <telerik:RadComboBoxItem Text="-- Select a Form --" Value="" /> </Items> </telerik:RadComboBox> <asp:RequiredFieldValidator ID="rfvForms" runat="server" ErrorMessage="Required" ControlToValidate="rcbForms" InitialValue="-- Select a Form --" Display="Dynamic" /> </EditItemTemplate> </telerik:GridTemplateColumn> <telerik:GridTemplateColumn HeaderText="Test" ReadOnly="true" UniqueName="TestForm" HeaderStyle-Width="1%" ItemStyle-HorizontalAlign="Center"> <ItemTemplate> <asp:HyperLink ID="hypTestForm" runat="server" NavigateUrl='<%# "FormsPreview.aspx?fid=" & Eval("FormID").ToString() & "&test=true" %>' Target="_blank"><asp:Image ID="imgTestProcess" runat="server" ImageUrl="~/Admin/Images/Test.png" ImageAlign="AbsMiddle" ToolTip="Test Form" /></asp:HyperLink> </ItemTemplate> </telerik:GridTemplateColumn> <telerik:GridTemplateColumn HeaderText="Header" SortExpression="Header" UniqueName="Header"> <ItemTemplate> <%#Eval("Form.Header")%>&nbsp; </ItemTemplate> </telerik:GridTemplateColumn> <telerik:GridTemplateColumn ReadOnly="true" ItemStyle-HorizontalAlign="Center" HeaderStyle-Width="1%" HeaderStyle-Wrap="false" ItemStyle-Wrap="false" UniqueName="SortOrder"> <ItemTemplate> <asp:ImageButton ID="ibnItemUpArrow" runat="server" Width="16" height="16" ImageUrl="~/Admin/Images/ArrowUp.png" ImageAlign="AbsMiddle" Visible='<%#IIF(Eval("SortOrder") = 0,false,true) %>' CommandArgument='<%#Eval("ID") %>' OnCommand=

    Read the article

  • jQuery override default validation error message display (Css) Popup/Tooltip like

    - by Phill Pafford
    I'm trying to over ride the default error message label with a div instead of a label. I have looked at this post as well and get how to do it but my limitations with CSS are haunting me. How can I display this like some of these examples: Example #1 (Dojo) - Must type invalid input to see error display Example #2 Here is some example code that overrides the error label to a div element $(document).ready(function(){ $("#myForm").validate({ rules: { "elem.1": { required: true, digits: true }, "elem.2": { required: true } }, errorElement: "div" }); }); Now I'm at a loss on the css part but here it is: div.error { position:absolute; margin-top:-21px; margin-left:150px; border:2px solid #C0C097; background-color:#fff; color:white; padding:3px; text-align:left; z-index:1; color:#333333; font:100% arial,helvetica,clean,sans-serif; font-size:15px; font-weight:bold; } UPDATE: Okay I'm using this code now but the image and the placement on the popup is larger than the border, can this be adjusted to be dynamic is height? if (element.attr('type') == 'radio' || element.attr('type') == 'checkbox') { element = element.parent(); offset = element.offset(); error.insertBefore(element) error.addClass('message'); // add a class to the wrapper error.css('position', 'absolute'); error.css('left', offset.left + element.outerWidth()); error.css('top', offset.top - (element.height() / 2)); // Not working for Radio, displays towards the bottom of the element. also need to test with checkbox } else { // Error placement for single elements offset = element.offset(); error.insertBefore(element) error.addClass('message'); // add a class to the wrapper error.css('position', 'absolute'); error.css('left', offset.left + element.outerWidth()); error.css('top', offset.top - (element.height() / 2)); } the css is the same as below (your css code) Html <span> <input type="radio" class="checkbox" value="P" id="radio_P" name="radio_group_name"/> <label for="radio_P">P</label> <input type="radio" class="checkbox" value="S" id="radio_S" name="radio_group_name"/> <label for="radio_S">S</label> </span>

    Read the article

< Previous Page | 647 648 649 650 651 652 653 654 655 656 657 658  | Next Page >