Search Results

Search found 18860 results on 755 pages for 'enigma machine'.

Page 651/755 | < Previous Page | 647 648 649 650 651 652 653 654 655 656 657 658  | Next Page >

• No network connection for vmware esxi guests

  - by JavaDev

  I'm new to VMware and setting up an Esxi server as a trial with the intention of possibly virtualizing some of our servers in the near future. I have setup ESXi on a Dell poweredge server, and installed a Centos 5.6 and Ubuntu 11.04 guest os on the server. However I cannot get networking on my guest OS's. The host is connected to a network with a DHCP server via a switch and is configured with a static IP. I have the default set-up for networking on the host: both guests are connected to the default vmnic1 adapter via the virtual switch vSwitch0. One thing though, the virtual adapter shows 'Observed IP ranges' to be XXX.XXX.XXX.194-XXX.XXX.XXX.195 (I've blanked out the initial prefixes) i.e just 1 address, even though the network the host is connected to has the usual 255.255.255.0 subnet mask. On the guest machines (using DHCP) by default, I can see an eth0 interface but with no connection or assigned IP address. A physical machine connected to the network gets a DHCP lease as expected. How do I get networking working on my guest OSes? Apologies for the long-winded question.

  Read the article

• Vmware Workstation, Win7 host, Ubuntu guests with Nat + Host-only networks but they cannot connect to the Internet

  - by Ikon

  I have a Win7 host machine with Vmware Workstation. In the workstation I have 3 Ubuntu installed. All 3 Ubuntu guests have a Nat network - to access the internet without asking the router for a local address - and a Host-only network - to connect all Ubuntu quests and the host in a private network for internal communication, without touching the router. When I try to make any of the Ubuntu quests to get data from the internet - assuming that they would figure out that the Nat-ed interface can access the requested data - they fail and report that there is no route to my query. If I disconnect the 2nd interface on the Ubuntu guests with the Host-only network and restart networking, they start to know the route to the internet. Odd, during the installation of the guests they asked which of the 2 given interfaces - with Nat and Host-only config - should be used to get updates during installation and they oddly managed to get the updates. Not so after the installation has finished and rebooted. I have checked the Virtual Network Editor that the Nat interface should use my real network card to access the net, so there should be no problem. I wish not to use the router's dhcp service to give the Ubuntu quests an address, and also I don't want the guests to be accessable from the local network directly, but only by the host - that's the Host-only network is for. Any suggestions? Edit: 192.168.189.0 is the Nat interface and 192.168.7.0 is the Host-only. $ route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.7.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 192.168.189.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 0.0.0.0 192.168.189.2 0.0.0.0 UG 100 0 0 eth0

  Read the article

• Why is my cron daemon is being killed every few minutes?

  - by user113215

  As of about a week ago, my cron daemon refuses to stay running. I'm using Debian 6 x64 on an OpenVZ virtual machine. Running something like pgrep cron shows that the daemon isn't running. I start the service with service cron start or /etc/init.d/cron start and it launches, but it disappears from the running process list after a few minutes (varying anywhere between 1 - 30 minutes before the process is killed again). Using strace -f service cron start, I can see that the process is being killed for some reason: nanosleep({60, 0}, <unfinished ...> +++ killed by SIGKILL +++ There's nothing relevant in /var/log/syslog, /var/log/messages, /var/log/auth.log, or /var/log/kern.log to explain why the the process is dying. The system has at least 800 MB of free memory, and cat /proc/loadavg returns 0.22 0.13 0.04 so resources shouldn't be the issue. With cron running, free -m reports: total used free shared buffers cached Mem: 1024 211 812 0 0 0 -/+ buffers/cache: 211 812 Swap: 0 0 0 I also tried removing and reinstalling the cron package using apt-get. Update: I initially thought the problem was a resource issues. I erased my entire VPS and started from a fresh Debian image. There is now nothing else running on the system, but even from a clean install my cron daemon is still being killed at random. What else should I check? How do I find out what's killing my crond?

  Read the article

• Windows mounted network drives slow after upgrading switch

  - by Kver

  On our small business network our old 10/100 consumer grade switch gave up the ghost, and we replaced it with a proper business-grade gigabyte switch. After wiring it in our Linux and Mac users immediately got back to working off of network drives; But 2 of our 3 Windows 7 PCs have suddenly experienced a tremendous slowdown with mapped network drives; Windows will become stuck "discovering" a folder causing applications to freeze when trying to open files. It will instantly display and browse files, but the moment you try to open one the bug hits. To remedy this we have our users copying files to the desktop, but it can take a few minutes while windows is stuck "calculating" the time it will take to copy. These aren't big files, mostly excel sheets less than 500KB - these operations are instant on Linux and Mac. (The third Windows machine is having no issues) I've tried remapping the drives, mapping to different drive letters, rebooting, etc. I'm at a loss, because switches are mostly transparent, and it's only after the switch was replaced that the Windows PCs started acting up. What black-magic voodoo am I missing to make Windows work? Thank you.

  Read the article

• RabbitMQ Management console not working

  - by rrejc

  I have started with RabbitMQ. I have a (windows) machine on which I installed two RabbitMQ nodes as a service - I have choose the nodename, port and service name for each of them. The services are running normally (i see that they are listening in a netstat-a). I have also installed management plugin with "rabbitmq-plugins enable rabbitmq_management" and restarted both services. But the plugin isn't running - I dont see it listening in a netstat and I can't connect to the management console via browser. Any idea what could be wrong? Is there any log to see what is goind on? Updated: when I do rabbitmq-plugins list i get: c:\RabbitMq\sbin>rabbitmq-plugins list [e] amqp_client 3.0.1 [ ] cowboy 0.5.0-rmq3.0.1-git4b93c2d [ ] eldap 3.0.1-gite309de4 [e] mochiweb 2.3.1-rmq3.0.1-gitd541e9a [ ] rabbitmq_auth_backend_ldap 3.0.1 [ ] rabbitmq_auth_mechanism_ssl 3.0.1 [ ] rabbitmq_consistent_hash_exchange 3.0.1 [ ] rabbitmq_federation 3.0.1 [ ] rabbitmq_federation_management 3.0.1 [ ] rabbitmq_jsonrpc 3.0.1 [ ] rabbitmq_jsonrpc_channel 3.0.1 [ ] rabbitmq_jsonrpc_channel_examples 3.0.1 [E] rabbitmq_management 3.0.1 [e] rabbitmq_management_agent 3.0.1 [ ] rabbitmq_management_visualiser 3.0.1 [e] rabbitmq_mochiweb 3.0.1 [ ] rabbitmq_mqtt 3.0.1 [ ] rabbitmq_old_federation 3.0.1 [ ] rabbitmq_shovel 3.0.1 [ ] rabbitmq_shovel_management 3.0.1 [ ] rabbitmq_stomp 3.0.1 [ ] rabbitmq_tracing 3.0.1 [ ] rabbitmq_web_stomp 3.0.1 [ ] rabbitmq_web_stomp_examples 3.0.1 [ ] rfc4627_jsonrpc 3.0.1-git7ab174b [ ] sockjs 0.3.3-rmq3.0.1-git92d4ba4 [e] webmachine 1.9.1-rmq3.0.1-git52e62bc

  Read the article

• Extracting information from active directory

  - by Nop at NaDa

  I work in the IT support department of a branch of a huge company. I have to take care of a database with all the users, computers, etc. I'm trying to find a way to automatically update the database as much as possible, but the IT infrastructure guys doesn't give me enough privileges to use Active Directory in order to dump the users, nor they have the time to give me the information that I need. Some days ago I found Active Directory explorer from Sysinternals that allows me to browse through Active Directory, and I found all the information that I need there (username, real name, date when it was created, privileges, company, etc.). Unfortunately I'm unable to export the data to a human readable format. I'm just able to take a snapshot of the whole database in a machine-readable format. Doing the snapshot takes hours and I'm afraid that the infrastructure guys won't like me doing entire snapshots on a regular basis. Do you know of any tool (command-line is preferable) that would allow me to retrieve the values of the keys or export it to XML, CSV, etc?

  Read the article

• How can one keep secure regular backups of his desktop on a remote server through aDSL? [on hold]

  - by Antonis Christofides

  I'm a system administrator and I use rsnapshot to backup some servers, duplicity for some others. Both work fine, each one with advantages and disadvantages. Despite that, I am at a loss on how to backup my own private files. I'd use duplicity to automatically backup my files to a remote server; but the problem is that once in a while I must do a full backup. My emails and important files are 9G, and I expect this to increase. Uploading through aDSL at 1Mbit would be 20 hours. Too much. rsnapshot doesn't require periodic full backups (only the first time), but it must be running on the remote server and have a means to connect to my computer; if the server is compromised (or simply if the NSA decides to use it), my own machine is also compromised. Not good. The only solution I've come up with is use encfs, use unison to synchronize the files to a remote server, and use duplicity or rsnapshot on the remote server to backup these files. In that case, the question is whether I can sync the files on many computers; is it possible for encfs to be used with the same key on many computers? I also think that if I append one character to the unencrypted file, its encrypted encfs counterpart might change a lot, so that incrementals with duplicity would be less efficient—but not a big deal. Maybe also, when I need to restore a file, finding the correct file to restore could be a pain, because of filename encryption. I wonder whether there is any other possibility that I've overlooked. Maybe I'm asking too much for my personal use, and I should settle with an external disk?

  Read the article

• How to Set Up an SMTP Submission Server on Linux

  - by Kevin Cox

  I was trying to set up a mail server with no luck. I want it to accept mail from authenticated users only and deliver them. I want the users to be able to connect over the internet. Ideally the mail server wouldn't accept any incoming mail. Essentially I want it to accept messages on a receiving port and transfer them to the intended recipient out port 25. If anyone has some good links and guides that would be awesome. I am quite familiar with linux but have never played around with MTA's and am currently running debian 6. More Specific Problem! Sorry, that was general and postfix is complex. I am having trouble enabling the submission port with encryption and authentication. What Works: Sending mail from the local machine. (sendmail [email protected]). Ports are open. (25 and 587) Connecting to 587 appears to work, I get a "need to starttls" warning and starttls appears to work. But when I try to connect with the next command I get the error below. # openssl s_client -connect localhost:587 -starttls smtp CONNECTED(00000003) depth=0 /CN=localhost.localdomain verify error:num=18:self signed certificate verify return:1 depth=0 /CN=localhost.localdomain verify return:1 --- Certificate chain 0 s:/CN=localhost.localdomain i:/CN=localhost.localdomain --- Server certificate -----BEGIN CERTIFICATE----- MIICvDCCAaQCCQCYHnCzLRUoMTANBgkqhkiG9w0BAQUFADAgMR4wHAYDVQQDExVs b2NhbGhvc3QubG9jYWxkb21haW4wHhcNMTIwMjE3MTMxOTA1WhcNMjIwMjE0MTMx OTA1WjAgMR4wHAYDVQQDExVsb2NhbGhvc3QubG9jYWxkb21haW4wggEiMA0GCSqG SIb3DQEBAQUAA4IBDwAwggEKAoIBAQDEFA/S6VhJihP6OGYrhEtL+SchWxPZGbgb VkgNJ6xK2dhR7hZXKcDtNddL3uf1YYWF76efS5oJPPjLb33NbHBb9imuD8PoynXN isz1oQEbzPE/07VC4srbsNIN92lldbRruDfjDrAbC/H+FBSUA2ImHvzc3xhIjdsb AbHasG1XBm8SkYULVedaD7I7YbnloCx0sTQgCM0Vjx29TXxPrpkcl6usjcQfZHqY ozg8X48Xm7F9CDip35Q+WwfZ6AcEkq9rJUOoZWrLWVcKusuYPCtUb6MdsZEH13IQ rA0+x8fUI3S0fW5xWWG0b4c5IxuM+eXz05DvB7mLyd+2+RwDAx2LAgMBAAEwDQYJ KoZIhvcNAQEFBQADggEBAAj1ib4lX28FhYdWv/RsHoGGFqf933SDipffBPM6Wlr0 jUn7wler7ilP65WVlTxDW+8PhdBmOrLUr0DO470AAS5uUOjdsPgGO+7VE/4/BN+/ naXVDzIcwyaiLbODIdG2s363V7gzibIuKUqOJ7oRLkwtxubt4D0CQN/7GNFY8cL2 in6FrYGDMNY+ve1tqPkukqQnes3DCeEo0+2KMGuwaJRQK3Es9WHotyrjrecPY170 dhDiLz4XaHU7xZwArAhMq/fay87liHvXR860tWq30oSb5DHQf4EloCQK4eJZQtFT B3xUDu7eFuCeXxjm4294YIPoWl5pbrP9vzLYAH+8ufE= -----END CERTIFICATE----- subject=/CN=localhost.localdomain issuer=/CN=localhost.localdomain --- No client certificate CA names sent --- SSL handshake has read 1605 bytes and written 354 bytes --- New, TLSv1/SSLv3, Cipher is DHE-RSA-AES256-SHA Server public key is 2048 bit Secure Renegotiation IS supported Compression: NONE Expansion: NONE SSL-Session: Protocol : TLSv1 Cipher : DHE-RSA-AES256-SHA Session-ID: E07926641A5EF22B15EB1D0E03FFF75588AB6464702CF4DC2166FFDAC1CA73E2 Session-ID-ctx: Master-Key: 454E8D5D40380DB3A73336775D6911B3DA289E4A1C9587DDC168EC09C2C3457CB30321E44CAD6AE65A66BAE9F33959A9 Key-Arg : None Start Time: 1349059796 Timeout : 300 (sec) Verify return code: 18 (self signed certificate) --- 250 DSN read:errno=0 If I try to connect from evolution I get the following error: The reported error was "HELO command failed: TCP connection reset by peer".

  Read the article

• Gateway laptop module bay light repeating 12 flashes - what error is that?

  - by Simurr

  I have a Gateway M465-E laptop currently running fine with a T2300E Core Duo installed. I wanted to upgrade it to a Core 2 Duo. My brother has the same model laptop and that took a Core 2 Duo (T7200) just fine. Picked up a T7200 on ebay and installed it. Normally when booting all the indicator lights flash once and the fan spins up before the machine actually starts to POST. With the T7200 installed all the lights flash and the fan spins up, but the module bay activity light flashes 12 times repeatedly. I'm assuming this is an error code, but can find no information about it. There are no beep codes. I've removed the ram, HD, Bay module and no change. Switched back to the T2300E and everything works fine. Anyone know what that error code is? The motherboard was actually manufactured by Foxconn if that helps. Update 1 Returned the CPU as defective. I tested it in 3 M465-E's and all of them did exactly the same thing. I still have no idea what the error code is. I'd still like to know for future reference. Perhaps I should try removing the CPU from one of them and see what happens.

  Read the article

• virtualized windows 2003 domain with CentOS 5.3 and poor connectivity

  - by Chris Gow

  Hi: I have a test lab set up running a virtualized windows 2003 domain on a CentOS 5.3(xen) host and am experiencing connectivity problems with guests running on other hosts that are part of the same domain. Here's the setup: On Computer A I have CentOS 5.3 running as the host and have virtualized windows 2003 servers for a primary domain controller, a backup domain controller and an exchange server. The primary domain controller also acts as a WINS and dns server. The windows domain appears on a separate subnet from my company's corporate network. Connectivity to any of the virtualized guests on Computer A is fine (remote desktop, ping, what have you). I have another host computer (Computer B) that also has a virtualized Windows 2003 server guest that is part of the same domain. However, connectivity to that guest is flaky at best. I continuously get at least 60% packet loss when I try to ping the guest, and due to that flakiness I can not access any of the services that it runs (remote desktop, web). Now here's the interesting part. It seems to affect only machines running on a different computer than the domain controller that are in the same domain. On Computer B there is another Windows 2003 guest that is not part of the test domain and is on my corporate network. There's no connectivity issues with that guest machine. The problem does not seem to be specific to Computer B either. I created a test VM on my local computer within the test domain and it exhibits the same behaviour as the guest in Computer B. A couple of items to note: - Host OS on both Computer A and B are the same CentOS 5.3 64 bit - Guest OS is Windows 2003 64 bit and 32 bit (the guest on Computer B is 32 bit) - Guest OSes are all up to date (as of Monday) - Host OS on Computer A was upgraded from CentOS 5.2 to 5.3 Update: Sorry I did not follow up with the comments from below. Computer A and B have been moved to their own dedicated switch and the problem has gone away. I'm not sure what the underlying problem(s) were though

  Read the article

• Adjust output Brightness/Gamma/Colors in Gnome

  - by Mikee

  We have a desktop system running Ubuntu 8.04.4, and it is connected to a standard desktop LCD monitor. Unfortunately, in 8.04.4, the brightness of the image is cranked way up. It appears to be a graphics driver issue. Unfortunately, installing a newer GPU driver for this Intel GPU is very difficult to do. So, I am looking for a software (or config file?) solution to achieve this. Note: Ubuntu 9.10 and higher do not exhibit this issue, so this is not a hardware problem. Note: VNC-ing to this machine from another does not exhibit this issue either. Also, I installed "DisplayCalibrator.app", and it does not work very well (the app comes up, but the contents of the window are blank). Is there anything that I can add to the xorg.conf file to correct this issue? Also, this solution: http://superuser.com/questions/96539/adjust-contrast-and-brightness-in-ubuntu did not resove my issue. Thank you all for the help!

  Read the article

• virtualized windows 2003 domain with CentOS 5.3 and poor connectivity

  - by Chris Gow

  I have a test lab set up running a virtualized windows 2003 domain on a CentOS 5.3(xen) host and am experiencing connectivity problems with guests running on other hosts that are part of the same domain. Here's the setup: On Computer A I have CentOS 5.3 running as the host and have virtualized windows 2003 servers for a primary domain controller, a backup domain controller and an exchange server. The primary domain controller also acts as a WINS and dns server. The windows domain appears on a separate subnet from my company's corporate network. Connectivity to any of the virtualized guests on Computer A is fine (remote desktop, ping, what have you). I have another host computer (Computer B) that also has a virtualized Windows 2003 server guest that is part of the same domain. However, connectivity to that guest is flaky at best. I continuously get at least 60% packet loss when I try to ping the guest, and due to that flakiness I can not access any of the services that it runs (remote desktop, web). Now here's the interesting part. It seems to affect only machines running on a different computer than the domain controller that are in the same domain. On Computer B there is another Windows 2003 guest that is not part of the test domain and is on my corporate network. There's no connectivity issues with that guest machine. The problem does not seem to be specific to Computer B either. I created a test VM on my local computer within the test domain and it exhibits the same behaviour as the guest in Computer B. A couple of items to note: - Host OS on both Computer A and B are the same CentOS 5.3 64 bit - Guest OS is Windows 2003 64 bit and 32 bit (the guest on Computer B is 32 bit) - Guest OSes are all up to date (as of Monday) - Host OS on Computer A was upgraded from CentOS 5.2 to 5.3 Update: Sorry I did not follow up with the comments from below. Computer A and B have been moved to their own dedicated switch and the problem has gone away. I'm not sure what the underlying problem(s) were though

  Read the article

• BackupExec 12 + RALUS - VERY slow backups

  - by LVDave

  We use Backup Exec 12 and the Remote Agent for Linux/Unix Servers (RALUS) to backup a large RHEL5 system. For various reasons we need to do a daily working set job. These working-set jobs run abysmally slow. The link between the target machine and the BE server is gigabit, and any other type of job runs 1-3GB/min. These working-set jobs start out at perhaps 40MB/min and over the course of the backup job slowly drops down so low that the BE job rate display in the "current jobs" goes blank.. Since we usually are only doing changed-files for one day, the job is usually small and finishes overnight and we don't worry abotu the slowness, but we had some issues with the backup server, and missed about 6 days of fairly heavy work on the Linux box, so this working-set job will be a doozy.. We have support with Symantec, and I've pestered them a lot about this, they've had me run RALUS in debug mode, sent them that log and a VXgather from the BE host and they had no fix/workaround.. To give an idea, I have the mentioned working-set job running for the last 3 1/2 hours and it's backed up just under 10MEGAbytes.... I'm posting this here to see if anybody in the "real world" has seen this/and/or has any ideas what might be causing these abysmally slow jobs, since Symantec seems to be clueless...

  Read the article

• Linux RAID: Replacing Failed Drive...permanantly

  - by user137519

  Okay, odd question here. I have a server with RAID 5. A drive failed, in a really physically in a really odd way. On the machine it boots and is seen by the BIOS but...no partition can be seen on the drive consistantly (in and out). 2 out of 3 drives working...I made new spare disk and added it, RAID 5 rebuilt clean. All appears well but...when I reboot it keeps trying to use the 2nd drive which doesn't give any partition data, so of course the RAID 5 gets 2 out of 3...again. The status of my drive is as follows: /dev/sda2:Good /dev/sdb2 (drive has physical problem so no partition data) bad, /dev/sdc2:good /dev/sdd2:good. Every time I reboot the mdadm system seems to keep trying to use /dev/sdb which has physical failure (although spins and is detected). /dev/sdd is the new drive I created. I added /dev/sdd to the raid and it rebuilds the raid but this action isn't memorized upon reboot so it keeps listing /dev/sda and /dev/sdc but doesn't use the perfectly good /dev/sdd until I re-add manually. I've tried removing the dead drive with the mdadm tool, but as it cannot see /dev/sdb paritions it will not fail or remove it (says partition doesn't exist). the /etc/mdadm.conf was automatically made on the original OS install which only lists: DEVICE partitions MAILADDR root ARRAY /dev/md2 super-minor=2 ARRAY /dev/md0 super-minor=0 ARRAY /dev/md1 super-minor=1 Basically just the raids to use on boot. I need to remove this semi-dead drive (/dev/sdb) but I'd prefer to know why this is happening before I do. any ideas or suggestions. I supposed I could attempt to clone/replace /dev/sdb (the partitions on drive show up, then disappear shortly after) but given the partition "chester cat" behaviour this seems risky to me and as I have a working "spare" it seems unnecessary. Thanks in advance for your insight.

  Read the article

• HP/Lenovo alternative to Buffalo iSCSI TerraStation?

  - by Robin Day

  I'm looking at virtualising some of our infrastructure in order to allow for more resiliance and future expandability. We have successfully virtualised on single servers with Direct Attached Storage and are now looking for a more future proof solution using a high powered host (or two) and a SAN (or two). I'm thinking that the host machine will probably be an HP ProLiant DL360 G7 (all of our exisiting infrastructure is HP). Unfortunately, I am new to the world of SANs. From what I can see, the Buffalo Terrastation III is all I would need in order to setup an iSCSI SAN for VMWare to use. However, I'm a little reticent to go that way as it's a bit too "entry level" for my liking. In particular I would be very keen for more redundancy, power, networking, etc. I'm also very aware that you "get what you pay for". Therefore, can anyone reccommend equivalents from the big boys? HP/Lenovo? I have searched high and low on the HP site and seen many options but am struggling to work out if it is all the hardware I will need. Some options appear to need separate controllers from disk enclosures, etc.

  Read the article

• Changing the Start Menu Power Button - Setting does not work: only (Shut down) is available

  - by Martin

  This is the second time I try to change this setting on a Vista based OS and I can't get it to work again. OS: Windows Server 2002 SP2 (not R2) = Microsoft Windows [Version 6.0.6002] = Vista When I go to: Power Options - Change Plan Settings - Change advanced power settings - Power buttons and lid - Start menu power button - Setting: the available combo box will only show the option Shut down. No other options are available. This server is part of a domain and has not been set up by me. I have not yet talked with the domain admin, but as far as I could tell from googling, only Win7 has group policy options for the start menu. (And yes, OC I will talk to the domain admin to see if he has any clue - which I doubt.) (Edit: I have now talked to our domain admin, and he's got no clue either.) I'm responsible for this server and a local administrator but not a domain administrator. I switched off User Account Control (UAC) yesterday without problems. Since I always log into this machine via RDP and this being a server, the natural choice would be the option (Log out) and not (Shut down). What can I do to fix it or to find out why it cannot be changed? Thanks!

  Read the article

• How do I troubleshoot nginx not recognizing passenger?

  - by Jade

  Issue: nginx does not seem to recognize my rails application Symptoms: When the server starts up, it shows the "Welcome to nginx!" message instead of my Rails application. Nginx seems to be using the local nginx path instead of the Rails root I specified: 2010/04/18 06:29:06 [error] 783#0: *1 "/usr/local/nginx/html/blog/index.html" is not found (2: No such file or directory), client: 1.2.3.4, server: www.farmerjade.com, request: "GET /blog/ HTTP/1.1", host: "www.farmerjade.com" I used [RVM and Passenger Setup on NGINX][1] to install nginx and passenger on a virtual machine. Here is my nginx configuration: user farmerjade; worker_processes 1; ... http { include mime.types; default_type application/octet-stream; passenger_ruby /home/farmerjade/.rvm/bin/passenger_ruby; passenger_root /home/farmerjade/.rvm/gems/ree-1.8.7-head/gems/passenger-2.2.11; ... server { listen 80; server_name www.farmerjade.com; root /home/farmerjade/farmerjade/public; passenger_enabled on; rails_env development; ... I'd appreciate any help anyone has to offer -- I'm quite new to nginx.

  Read the article

• OS X Application icons missing after filesystem tampering

  - by dylan

  A while back I installed some Google software, I forget what it was, but it was something that attached itself to Google Chrome and was un-uninstallable short of uninstalling all of Chrome. It was a total pain in the a$$. Anyways, I was trying to put up a fight before going nuclear and just wiping Chrome, and during that fight, something went wrong (i.e., I didn't know what I was doing). I remember messing around with the Applications folder somehow. I don't remember what exactly I did, but it perhaps involved some interchanging between the /Applications and /User/Username/Applications folders? Definitely some tampering in those areas, I'm sure at least about that. Anyways, I've since updated and restarted my computer. Now, while all my apps work fine, many of them have blank icons - not on the Dock, those icons are fine, but in Spotlight search results, etc. Currently, my /Applications folder contains only OS X-cooked-in applications. My ~/Applications folder contains cooked in apps AND post-OS/third-party apps. There hasn't been any functionality deficit so far, but I don't like working on a machine where something isn't how it should be. I know my information was vague, but does anyone know what went wrong / how to fix it? OS X Mavericks 10.9.3

  Read the article

• How to locate phpmyadmin on ubuntu

  - by Chris

  Okay, I'm usually a windows user and I write quite happily there, unfortunately (or fortunately) I have installed linux on a dual boot and having installed some software I have a question... Where is it? I installed Apache, PHP, MySQL and separately phpmyadmin, Apache is up and running, I've seen my phpinfo page and MySQL is there. MySQL is telling me that there's a database for phpmyadmin, but...erm.. I can't seem to locate it. On a windows machine the directory would be in the www directory and I'd just navigate there... localhost/phpmyadmin/ but on Ubuntu I can't find it in the equivalent. I've been to /var/www/ and there's my index.html (from apache) and my phptest.php file but no phpmyadmin. There is a phpmyadmin in /lib but that only has 2 files in it. So having rambled lots, my question is, what do I have to do to be able to navigate to the phpmyadmin index page? I realise this could fall under the description of a server related question and should be posted elsewhere but as it's software on a home system some help would be appreciated. Do I need to move some files from somewhere? Help! I really don't want to have to go back to developing on Windows as I'll be deploying to a lamp system, my learning curve will be steep.

  Read the article

• Sharing music on NAS with Zune and iPod?

  - by osij2is

  After being a long time iPod owner, I'm switching to the new Zune with its subscription model. I haven't bought a Zune yet but I'm planning on doing so within the next month or so. I have approximately 40GB worth of music and my girlfriend has her iPod music library around 30GB. I've been trying to figure out how to migrate all our music off of our laptops/desktops and centralize everything on my NAS. In sharing iPod music isn't too bad. Sharing from one machine to all is fairly easy within the iTunes player. As far as storing all the music on a NAS, again, iPods aren't too bad and imagine other systems aren't difficult. But I'm really new to the Zune and I'm beginning to run into some issues. My questions are: Is it possible to store all music from our iPods and Zune subscriptions and share music between the iPod/Zune within the same file share on my NAS? I'm sure it's possible to store music on a share, but I'm not sure how iTunes and the Zune software differs. Is there 3rd party software, maybe something like DoubleTwist that can sync based from NAS to multiple desktop/laptops? I've never used DoubleTwist but it's something that I found that looks close to being what I need. I've never quite done this myself so I'm trying to find a solution that can: a) store music on a network share; b) sync between different devices (Zune/iPod) seamlessly.

  Read the article

• Redmine does not return the web page

  - by m0skit0

  I migrated a Redmine installation from an Ubuntu machine to a Debian one (both 32-bits), and now for some reason, for some users it doesn't return the page but only a 200 OK message. Here is the flow (from Wireshark): GET /issues/142 HTTP/1.1 Host: debian:3000 User-Agent: Mozilla/5.0 (X11; Ubuntu; Linux i686; rv:17.0) Gecko/20100101 Firefox/17.0 Accept: text/html,application/xhtml+xml,application/xml;q=0.9,*/*;q=0.8 Accept-Language: en-US,en;q=0.5 Accept-Encoding: gzip, deflate Connection: keep-alive Cookie: _redmine_session=BAh7DCIQX2NzcmZfdG9rZW4iMStIM1RBNTlNelZVUXlUazgrR1pUNGUvNGdEbytUZzRyMVFSUnBvNGhlSDg9Ihd0aW1lbG9nX2luZGV4X3NvcnQiEnNwZW50X29uOmRlc2MiD3Nlc3Npb25faWQiJThiMDk0MzVhOTEzYTI0MzVjOGEzYTRmNDU0NzcwMTAwIgx1c2VyX2lkaQoiFmlzc3Vlc19pbmRleF9zb3J0IgxpZDpkZXNjIg1wZXJfcGFnZWlpIgpxdWVyeXsHOg9wcm9qZWN0X2lkaQc6B2lkaQo%3D--8588c221c0642a12f396239455fb702aec14c9c9; my_wiki_session=f70ae11e1c533c86f0e039d63cf3f69c; my_wikiUserID=1; my_wikiUserName=Yasin Cache-Control: max-age=0 HTTP/1.1 200 OK Connection: Keep-Alive Date: Wed, 12 Dec 2012 16:30:16 GMT Server: WEBrick/1.3.1 (Ruby/1.8.7/2010-08-16) Content-Length: 0 As you can see, I get nothing from the server. This is mostly random because this blank page happens sometimes for some users, and for other users it almost never returns the page... I'm absolutely lost here. Any idea about what can be the cause? Thanks in advance!

  Read the article

• Forward all traffic from one IP to another Ip on OS X

  - by Josh

  This is related to this question I just asked... I have two IP address on my iMac I want to "bridge". I'm not sure what the proper terminology is... here's the situation. My iMac has a firewire connection to my laptop and an ethernet connection to the rest of my office. My laptop has an ip of 192.168.100.2 (on the firewire interface). My iMac has an IP of 192.168.100.1 on the firewire interface, and two IPs, 10.1.0.6 and 10.1.0.7, on it's ethernet interface. If I wanted to forward all traffic coming in from 192.168.100.2 on my OS X machine to go out on IP 10.1.0.7, and vice-versa, can this be done? I assume I would use the ipfw command. Essentially I want to "bridge" the firewire network to the ethernet network so my laptop can see all the machines on the 10.1 network, and all those machines can see my laptop at 10.1.0.7. Is this possible?

  Read the article

• Trying to Set up SMTP Server on WIndows Server 2012

  - by datc

  I'm working on a website, and I need to test the functionality of sending email messages from ASP.NET, something like this: Dim msg As New MailMessage("email1", "email2") msg.Subject = "Subject"<br> msg.IsBodyHtml = True<br> msg.Body = "Click <a href='site'>here</a>." Dim client As SmtpClient = New SmtpClient() client.Host = "My-Server"<br> client.Port = 25<br> client.DeliveryMethod = SmtpDeliveryMethod.Network<br> client.Send(msg) This is running from a Windows 8 workstation. I've installed SMTP server on my Windows Server 2012 machine. The mail shows up in the mailroot/Queue folder and sits there, eventually getting deposited into Badmail. Now I have AT&T U-verse at home, and a few devices connected to the gateway, including let's call it "My-Server." When I run SmtpDiag from say, datc@... to [email protected] I get SOA serial number match passed, Local DNS (99-135-60-233.lightspeed.bcvloh.sbcglobal.net) & Remote DNS (hotmail.com) tests *not* passed, and ultimately, Connecting to the server failed. Error: 10060. Failed to submit mail to mx2.hotmail.com error. When I set My-Server's IP to static and equal to the external IP, 99.135.60.233, and again run SmtpDiag, I get SOA, Local DNS, and Remote DNS tests passed, but the same 10060 error. Same for yahoo.com, gmail.com, and so forth. Is it my ISP's job to fix this? Some PTR record missing somewhere? Is it at all possible to have a home-based SMTP server? All I want is to test my email code. Perhaps, my IP address is just not "trusted" somehow. Thanks.

  Read the article

• finding files that match a precise size: a multiple of 4096 bytes

  - by doub1ejack

  I have several drupal sites running on my local machine with WAMP installed (apache 2.2.17, php 5.3.4, and mysql 5.1.53). Whenever I try to visit the administrative page, the php process seems to die. From apache_error.log: [Fri Nov 09 10:43:26 2012] [notice] Parent: child process exited with status 255 -- Restarting. [Fri Nov 09 10:43:26 2012] [notice] Apache/2.2.17 (Win32) PHP/5.3.4 configured -- resuming normal operations [Fri Nov 09 10:43:26 2012] [notice] Server built: Oct 24 2010 13:33:15 [Fri Nov 09 10:43:26 2012] [notice] Parent: Created child process 9924 [Fri Nov 09 10:43:26 2012] [notice] Child 9924: Child process is running [Fri Nov 09 10:43:26 2012] [notice] Child 9924: Acquired the start mutex. [Fri Nov 09 10:43:26 2012] [notice] Child 9924: Starting 64 worker threads. [Fri Nov 09 10:43:26 2012] [notice] Child 9924: Starting thread to listen on port 80. Some research has led me to a php bug report on the '4096 byte bug'. I would like to see if I have any files whose filesize is a multiple of 4096 bytes, but I don't know how to do that. I have gitBash installed and can use most of the typical linux tools through that (find, grep, etc), but I'm not familiar enough with linux to figure it out on my own. Little help?

  Read the article

• How to configure hostname for `apache22` package on FreeBSD?

  - by Eonil

  I'm configuring development & test FreeBSD machine on VM. I installed apache22 package and restarted. But the daemon does not started with this error: %apachectl start httpd: apr_sockaddr_info_get() failed for test.box httpd: Could not reliably determine the server's fully qualified domain name, using 127.0.0.1 for ServerName (13)Permission denied: make_sock: could not bind to address [::]:80 (13)Permission denied: make_sock: could not bind to address 0.0.0.0:80 no listening sockets available, shutting down Unable to open logs % My hostname is test.box. Because this is temporary test box, it has no real domain-name. But I used 2-level name to avoid long time waiting of sshd on booting. However, I searched web, and I modified /etc/hosts file like this (I didn't touches this file before): # This is original configuration #::1 localhost localhost.my.domain #127.0.0.1 localhost localhost.my.domain # New configuration ::1 localhost test.box 127.0.0.1 localhost test.box 127.0.0.1 test.box test Now apache fails with this error message: %apachectl start httpd: Could not reliably determine the server's fully qualified domain name, using test.box for ServerName (13)Permission denied: make_sock: could not bind to address [::]:80 (13)Permission denied: make_sock: could not bind to address 0.0.0.0:80 no listening sockets available, shutting down Unable to open logs % I don't know what's required now. Please let me know reason and solution of this error. ---- (edit) ---- The permission errors are caused from omission of sudo.

  Read the article

< Previous Page | 647 648 649 650 651 652 653 654 655 656 657 658  | Next Page >