Search Results

Search found 50990 results on 2040 pages for 'system center'.

Page 651/2040 | < Previous Page | 647 648 649 650 651 652 653 654 655 656 657 658  | Next Page >

  • NVRAM for journals on Linux?

    - by symcbean
    I've been thinking about ways of speeding up disk I/O, and one of the bottlenecks I keep coming back to is the journal. There's an obvious benefit to using an SSD for the journal - over and above just write caching unless of course I just disable the journal with the write cache (after all devicemapper doesn't seem to support barriers). In order to get the benefits from using a BB write cache on the controller, then I'd need to disable journalling - but then the OS should try to fsck the system after an outage. Of course if the OS knows what's in the batter-backed memory then it could use it as the journal - but that means it must be exposed as a block device and only be under the control of the operating system. However I've not been able to find a suitable low-cost device (no, write-levelling for Flash is not adequate for a journal, at least one which uses Smartmedia). While there's no end of flash devices, disk/array controllers with BB write caches, so far I've not found anything which just gives me non-volatile memory addressable as a block storage device.

    Read the article

  • problems with WindowsImageBackup and write protected drives

    - by Ralph Shillington
    On Windows 7 I created a System image of my computer (C: and reserved partition) onto a USB drive. No problem. I then formatted the C: and installed the OS -- no problem Now I would like use the System Image and get back some of my documents etc. But I can't get access wo the WindowsImageBackup folder on the USB drive 1) Somehow the drive is write protected --- how did that happen? How do I unprotect that drive. 2) I can't access the WindowsImageBackup folder because I suspect the ACL is out of wack with my new SID. I would add my new SID to the ACL but I can't because the drive is write protected At the moment I'm completely disconnected from my files, which I thought (and still hope) are backed up. Understandably, panic is now setting in.

    Read the article

  • Disable Charm bar's Touchpad gesture shortcut

    - by Chin
    I'm using an Acer AO722 laptop. Everytime I slide my finger from the right edge of the touchpad (where the slider is) toward the center (mostly accidentally), the charmbar pops up and stays on the screen until I manually click on some random spots on the screen. There's no such option in the Synaptics properties: .. nor is there any in the mouse option. Is there a way to turn this shortcut off?

    Read the article

  • How to forward UDP and TCP traffic from one IP to another

    - by Rishabh Agnihotri
    Well i have a server with two LAN Card Installed.I have a server in U.S and one in India.I have created a GRE tunnel to route all traffic from U.S Server to my Indian Server.My Traffic has UDP,TCP,HTTP,etc Traffic.Now i have two LAN Card on my Indian Server.Well i have configured two IPs on the system for some of my needs on the system.One is a /30 and another is a /24.Well now i want the /30 IP to talk to my /24 IP.Lets take a e.g the IPs are 180.151.130.34 - /30 and 103.243.19.254 -/24 I want to forward all the TCP,UDP,HTTP,etc like traffic coming to 180.151.130.34 to 103.243.19.254.In the sense i want to make them talk to each other in a way if a TCP/UDP Packet comes to 180.151.130.34 it should be forwarded to 103.243.19.254 and then that packet is sent back by 103.243.19.254 to 180.151.130.34.I am not able to configure this part.Can anyone tell me step by step how to do so? Well i forgot to specify i am using Windows Server 2008. Any help would be greatly appreciated.Thanks in advance.

    Read the article

  • Header precendence: Apache Vs. PHP specific to cache-control & expires

    - by David
    My companies production dynamic web servers ( Apache + PHP 5.1x) are using the Apache expires module and there is a clause inside http.conf as follows: <FilesMatch ".+"> ExpiresActive On ExpiresDefault "A0" </FilesMatch> If I were to set inside a php script "Cache-Control" and "Expires", would it get eaten by this clause? Normally I would test this on my own but having trouble convincing the Expires module to function on my workstation and the company Admin's are down at the data-center.

    Read the article

  • How can I perform a controlled shutdown of a virtualbox guest using VBoxManage?

    - by Bryan
    I'm currently testing Ubuntu 10.04, and have install the VirtualBox software. I have also installed Ubuntu 10.04 as a VirtualBox guest running on the host system. I've installed the VirtualBox Utils into the guest OS, as follows: sudo apt-get install virtualbox-ose-guest-utils What I want to be able to do is to initiate a controlled shutdown of the guest, from the host system using the VBoxManage command. I first tried this command: VBoxManage controlvm guest poweroff which worked, but didn't initiate a controlled shutdown, it effectively pulls the plug on the guest. I've since found that this command should do the trick: VBoxManage controlvm guest acpipowerbutton but this doesn't appear to do anything. Can anyone tell me what I'm doing wrong? p.s. I don't want to use SSH & Certificates to do this, as I'm also going to be running Windows guests, and I want the solution to work for all guests.

    Read the article

  • SCO UNIX problem: "Cannot create /var/adm/utmp or /var/adm/utmpx"

    - by Maktouch
    Hey everyone, I have an old server that doesn't boot. I don't know the version of unix installed, but I see SCO UNIX. It stops with that error: UX:init: ERROR: Cannot create /var/adm/utmp or /var/adm/utmpx UX:init: ERROR: failed write of utmpx entry: " " UX:init: ERROR: failed write of utmpx entry: " " UX:init: INFO: SINGLE USER MODE After that message, it just stops. I cannot write or press anything. Even CTRL + ALT + DEL does not work. I cannot get into the system. I have tried booting with a DamnSmallLinux LiveCD but it does not recognize the file system on HDA. Is there a way to either log in as root or bypass this error? Thanks.

    Read the article

  • How to send local mail via postfix to another server

    - by scotts
    I have postfix set up for use as an STMP server to send mail for my domain, but I receive email for the domain via gmail/google apps. The reason I use my own postfix is because I send out a lot of transactional emails to my customers using a web app, and the volume would exceed what google allows with its SMTP servers. Everything works fine, except cron & system mail gets routed to local users on the server, not to the appropriate accounts at google mail. How can I route this system mail to the respective google mail accounts instead?

    Read the article

  • routing wiredness - traceroute 'vanishes' en route

    - by The Journeyman geek
    I'm attempting to set up one of my boxes as a server (again), but i'm having some odd connection issues- the box itself connects fine to the internet, but trying to connect to my external ip address seems to result in the trace getting 'lost' partway. http://pastebin.com/HCQAGbvn - this is a traceroute from another system that's connected to another ISP - starhub is my own one, while i have another system that i have access to on singtel. I'm wondering if my ISP is messing around with routing, or is something very odd going on. As you note, the traceroute dosen't reach me, but if it helps, i use a dd-wrt router.

    Read the article

  • MediaPortal crash when scanning my TV Channels

    - by Martin Ongtangco
    Hello, I tried installing MediaPortal (http://www.team-mediaportal.com) on my old system. I installed & tried both beta & stable releases: Here's the old system specs: Windows XP SP3; 512mb DDR; 80GB IDE; K-World PVR-TV7131 Analog TV-Tuner; Inno3d FX5500 128mb 64bit; When scanning through the TV-Server, it crashes. I don't know if the incompatibility comes from the hardware or the OS, but my TV Tuner's own Media center app works well. For now, that's what im using. Anyone here familiar with MediaPortal? Thanks!

    Read the article

  • What is the impact of Windows 8 with UEFI on normal users?

    - by Sam
    I am a normal man-in-the-street computer user and so do not really understand what this is about, but I want to. Can someone please explain to me if: The Windows 8/UEFI secure boot thing will make it impossible to run normal/legacy applications in Windows 8 (as they will be unsigned)? It will turn Windows into an Apple-like system where only Microsoft approved applications can be run? As I say, I'm a normal user, and that is the overall impression I have from reading all the blogs, etc about it. If, on the other hand, all it does is make sure the system is booting a signed OS, how does this prevent malware (which is what at least two Microsoft blogs that I read seemed to be saying), given that most malware is not part of the boot process? The only way I can see this making sense is if it is ensuring that all OS components are signed. Is that it? Like I say, I'm a mortal, so please don't get technical on me, but rather explain how it will affect me, the user.

    Read the article

  • Can't set acl for afs even though i'm in the right group

    - by Torandi
    I've got a dir that i've lost controll over in an afs system. According to the system adminstrators my adminin subgroup (dsekt:admin) got rlidwka on the dir. I'm a member of this group (and i can list the members of the group and see my nick there) though I can't set the acl's for the dir. The pts: $pts membership dsekt:admin Members of dsekt:admin (id: -6813) are: /.../ taran And my klist. $>klist Credentials cache: FILE:/tmp/krb5cc_56782 Principal: [email protected] Both dsekt:admin and the dir is on the NADA.KTH.SE node.

    Read the article

  • Editing .bash_profile file not taking effect

    - by Sandeepan Nath
    I need to put export PATH=$PATH:/opt/lampp/bin to my ~/.bash_profile file so that mysql from command line works on my system. Please check mysql command line not working for further details on that. I am working on a fedora system and logged in as root user. If I run locate .bash_profile then I get these:- /etc/skel/.bash_profile /home/sam/.bash_profile /home/sohil/.bash_profile /home/windows/.bash_profile /root/.bash_profile So, I modified the /root/.bash_profile file like this:- from PATH=$PATH:$HOME/bin export PATH to PATH=$PATH:/opt/lampp/bin export PATH But, still the change is not taking effect - Opening a new console and running mysql again says bash: mysql: command not found. However running export PATH=$PATH:/opt/lampp/bin in console makes it work for that session. So, I am doing something wrong with the .bash_profile file. May be editing incorrect one or doing the edit incorrectly.

    Read the article

  • Strange strace and setuid behaviour: permission denied under strace, but not running normally.

    - by Autopulated
    This is related to this question. I have a script (fix-permissions.sh) that fixes some file permissions: #! /bin/bash sudo chown -R person:group /path/ sudo chmod -R g+rw /path/ And a small c program to run this, which is setuided: #include "sys/types.h" #include "unistd.h" int main(){ setuid(geteuid()); return system("/path/fix-permissions.sh"); } Directory: -rwsr-xr-x 1 root root 7228 Feb 19 17:33 fix-permissions -rwx--x--x 1 root root 112 Feb 19 13:38 fix-permissions.sh If I do this, everything seems fine, and the permissions do get correctly fixed: james $ sudo su someone-else someone-else $ ./fix-permissions but if I use strace, I get: someone-else $ strace ./fix-permissions /bin/bash: /path/fix-permissions.sh: Permission denied It's interesting to note that I get the same permission denied error with an identical setup (permissions, c program), but a different script, even when not using strace. Is this some kind of heureustic magic behaviour in setuid that I'm uncovering? How should I figure out what's going on? System is Ubuntu 10.04.2 LTS, Linux 2.6.32.26-kvm-i386-20101122 #1 SMP

    Read the article

  • NIC light is turned off after boot on Redhat 4.6 server

    - by hoffmandirt
    I have a 2950 blade server setup with Red Hat 4.6 installed. I cannot get the NIC to work properly after reinstalling Linux. I activated the NIC, but the NIC light will not turn on when I plug the network cable into the hub. The status light on the hub will not turn on either. If I run ifconfig, the NIC status is UP. Also I can ping the IP address that I assign to the Linux machine, but I can't ping anything else that is plugged into the hub. When I reboot the system, the NIC light will stay on until the system fully boots and then it will turn off again. Is there something else that I need to do to get the NIC working? It appears to be disabled even though ifconfig says that it is UP. Maybe I need to configure something within the blade server (iDRAC)?

    Read the article

  • How to force Debian to boot new Kernel?

    - by ThE_-_BliZZarD
    I'm running Debian 6, Debian GNU/Linux, with Linux 2.6.32-5-amd64 under Grub2 ( 1.98+20100804-14+squeeze1) on a remote system (no possibility to view the pre-boot messages). I compiled and installed a new kernel, but I can not get it to boot. What I have done: Installed the packages via: dpkg -i linux-headers-3.5.3.20120914-amd64_3.5.3.20120914-amd64-10.00.Custom_amd64.deb linux-image-3.5.3.20120914-amd64_3.5.3.20120914-amd64-10.00.Custom_amd64.deb This updated the Grub configuration. My /boot/grub/grub.cfg now contains: menuentry 'Debian GNU/Linux, with Linux 3.5.3.20120914-amd64' --class debian --class gnu-linux --class gnu --class os { insmod raid insmod mdraid insmod part_msdos insmod part_msdos insmod ext2 set root='(md0)' search --no-floppy --fs-uuid --set 5a3882a9-c7df-4f6a-9feb-f03e3e37be01 echo 'Loading Linux 3.5.3.20120914-amd64 ...' linux /vmlinuz-3.5.3.20120914-amd64 root=UUID=003242b5-121b-49f3-b32f-1b40aea56eed ro acpi=ht quiet panic=10 echo 'Loading initial ramdisk ...' initrd /initrd.img-3.5.3.20120914-amd64 } menuentry 'Debian GNU/Linux, with Linux 2.6.32-5-amd64' --class debian --class gnu-linux --class gnu --class os { insmod raid insmod mdraid insmod part_msdos insmod part_msdos insmod ext2 set root='(md0)' search --no-floppy --fs-uuid --set 5a3882a9-c7df-4f6a-9feb-f03e3e37be01 echo 'Loading Linux 2.6.32-5-amd64 ...' linux /vmlinuz-2.6.32-5-amd64 root=UUID=003242b5-121b-49f3-b32f-1b40aea56eed ro acpi=ht quiet panic=10 echo 'Loading initial ramdisk ...' initrd /initrd.img-2.6.32-5-amd64 } I used grub-set-default "Debian GNU/Linux, with Linux 2.6.32-5-amd64" to set the old kernel as default and then grub-reboot "Debian GNU/Linux, with Linux 3.5.3.20120914-amd64" to boot into the new kernel once. After update-grub I rebooted the system, but everytime it comes back up with the old kernel (2.6). I tried setting the new one as default (grub-set-default 0, update-grub, reboot) but, still the old one. The Syslogs contain NO hint whatsoever about trying to boot the new kernel - only the old one. Would there be any hints regarding problems with a kernel? Is there a way to enable debug-logging in grub? What am I doing wrong? How can I force the system to boot the new kernel? Edit: Hardware of remote machine. CPU cat /proc/cpuinfo processor : 0 vendor_id : AuthenticAMD cpu family : 16 model : 5 model name : AMD Athlon(tm) II X4 605e Processor stepping : 3 cpu MHz : 2294.898 cache size : 512 KB physical id : 0 siblings : 4 core id : 0 cpu cores : 4 apicid : 0 initial apicid : 0 fpu : yes fpu_exception : yes cpuid level : 5 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx fxsr sse sse2 ht syscall nx mmxext fxsr_opt pdpe1gb rdtscp lm 3dnowext 3dnow constant_tsc rep_good nonstop_tsc extd_apicid pni monitor cx16 popcnt lahf_lm cmp_legacy svm extapic cr8_legacy abm sse4a misalignsse 3dnowprefetch osvw ibs skinit wdt bogomips : 4589.77 TLB size : 1024 4K pages clflush size : 64 cache_alignment : 64 address sizes : 48 bits physical, 48 bits virtual power management: ts ttp tm stc 100mhzsteps hwpstate (copied only the first, 3 more follow) The server is a Fujitsu PRIMERGY MX130 S1.

    Read the article

  • Letters seem to be rendered wrongly in Firefox

    - by BloodPhilia
    So, when I'm browsing in firefox, some letters look grainy or glowing, does anyone know what might be causing this? It doesn't show on all website, only some. It almost looks like Firefox is trying to render different font colours on top of eachother and blends them in the process somehow. Using Firefox 3.6.13 on Windows 7 Ultimate 64 bits and the problems also arrise when running Firefox in safe mode. http://facelift.mawhorter.net/ (top menu) IE 8: FF 3: https://student.ru.nl/portal/dt (center notification) IE 8: FF 3:

    Read the article

  • Connect to wired and wireless networks at same time, Ubuntu

    - by Gary Chambers
    Currently, I have a media PC running Ubuntu 10.04 that I am trying to connect via a wired network cable directly to a NAS box, and wirelessly to the router. This works no problem after I run sudo /etc/init.d/networking restart but I can't get both interfaces to come up on system startup. My /etc/network/interfaces file reads as follows: auto eth0 iface eth0 inet static address 10.0.1.2 netmask 255.255.254.0 broadcast 10.0.1.255 network 10.0.1.0 auto wlan2 iface wlan2 inet dhcp As I say, I know this works, because I can get it to work by restarting the network interfaces, but I can't bring them both up on system startup. Does anyone know why this might be?

    Read the article

  • How to add a web folder via command line (Windows)

    - by Ryan
    I am trying to add a web folder via command line in windows. At first I though I should use the "net use" command, but when I tried I kept getting System error 67: C:net use * http://dev.subdomain.domain.tdl/dav/ the user name for 'dev.subdomain.domain.tdl': correctusername the password for dev.subdomain.domain.tdl: System error 67 has occurred. The network name cannot be found. The url I used works in a browser. It's an Apache dav on basic auth LDAP authentication method being used. Here's the thing... I CAN create a web folder when I use the "Add a network place" wizard. When I do net use, I don't see it listed in the prompt that follows. What utility do I need to use to mount a web folder in command line?

    Read the article

  • Resizing mysterious partition written by DDing an ISO file

    - by Jon
    I downloaded clonezilla and then wrote it to a USB flash drive with this: dd if=clonezilla.iso of=/dev/sdb I've confirmed that the system boots and clonezilla runs from the flash drive. I want to store a clonezilla backup on the same flash drive clonezilla is running on, but I tried it and ran out of space, so I started looking at how to resize the mysterious partition type that was generated from the ISO. fdisk -l /dev/sdb .... Device Boot Start End Blocks Id System /dev/sdb1 * 1 111 113664 17 Hidden HPFS/NTFS .... I've tried using ntfsresize from the Debian ntfsprogs package. I'm trying gparted next, but thought I'd ask here if anyone knows a neat way to resize a partition created on flash from a liveCD image. Thanks in advance Jon ps. Assume Debian 6 please.

    Read the article

  • How to get rid of prompts for credentials connecting to proxy Server officeimg.vo.msecnd.net in Office 2013?

    - by Firee
    I have experienced this issue mainly with Excel, Word and Powerpoint 2013, where there is constant pop-up box asking for login credentials as it tries to connect to officeimg.vo.msecnd.net I have searched and found one of the solution, to prevent Office from connecting to the internet (Options Trust Center Settings Allow Office to connect to internet). This solution worked for sometime, but am back to square one again. Solutions are sought, as this is a nagging problem, I am sure others would have experienced the same.

    Read the article

  • How to view bad blocks on mounted ext3 filesystem?

    - by Basilevs
    I've ran fsck -c on the (unmounted) partition in question a while ago. The process was unattended and results were not stored anywhere (except badblock inode). Now I'd like to get badblock information to know if there are any problems with the harddrive. Unfortunately, partition is used in the production system and can't be unmounted. I see two ways to get what I want: Run badblocks in read-only mode. This will probably take a lot of time and cause unnecessary bruden on the system. Somehow extract information about badblocks from the filesystem iteself. How can I view known badblocks registered in mounted filesystem?

    Read the article

  • how to word wrap, align text like the output of man?

    - by cody
    what is the command that word wraps and justifies a text file so that the output looks like that of a man page: All of these system calls are used to wait for state changes in a child of the calling process, and obtain information about the child whose state has changed. A state change is considered to be: the child terminated; the child was stopped by a signal; or the child was resumed by a signal. In the case of a terminated child, performing a wait allows the system to release the resources associated with the child; if a wait is not performed, then the termi- nated child remains in a "zombie" state (see NOTES below). Thanks.

    Read the article

  • How to set CHKDSK for drive C: in Windows 7

    - by prashanth
    I recently got a 0xc000007b error whenever I tried to run some application software. I found that CHKDSK for C drive might be a solution. When I tried to do it from C drive properties, it said the drive was in use and asked to schedule CHKDSK at the next reboot. I clicked OK. When I restart, I experience a BSOD. I waited for 10 minutes but still nothing happens. So I forced a shutdown (laptop) and again booted up the computer and got a BSOD for just 5 or 10 seconds and system boots and works with no problem. I repeated all these steps four or four times and yet with the same results. Is there any other way other than CHKDSK to solve the 0xc000007b error? If not, why is CHKDSK not working at boot up? Can I force CHKDSK on drive C: to perform while the system is on? Platform: Windows 7 64-bit.

    Read the article

  • Selecting which object to align to in Powerpoint 2007

    - by Ash
    When doing an alignment in Powerpoint 2007 (say, Align Center), is there any way to select which object will be aligned to? It seems to pick one of the objects, but I'm not sure how it decides which one to pick and how to change it. Order of selection and front/back ordering seems to have no effect. Anyone have any ideas?

    Read the article

< Previous Page | 647 648 649 650 651 652 653 654 655 656 657 658  | Next Page >