Search Results

Search found 90790 results on 3632 pages for 'user accounts'.

Page 651/3632 | < Previous Page | 647 648 649 650 651 652 653 654 655 656 657 658  | Next Page >

• Diagnosing laptop charging issues

  - by Ben

  My HP dv6000 laptop will not run on battery power. It will only run while plugged into the wall. I have already replaced the battery, but it still will not operate on battery power. The problem began slowly. The original battery's life got shorter and shorter, until eventually it would only last ~45 seconds before going into hibernation. Finally, the battery would not work at all, so I threw it out and just used it without a battery. I bought a replacement recently.... but the problem persists. When I connect the new battery to the system, the "charging" light turns on for about 30 seconds, then goes dark. I'm assuming there's something wrong with the internal charging circuitry? If this is the case, how would I go about fixing this, short of buying a new motherboard? If anyone could give me some assistance in confirming/rejecting my diagnosis I'd be very appreciative! :)

  Read the article

• Raid-1 Western Digital Green AARS, cloning and WD Align Utility

  - by Jaguar

  Hello all, My current setup runs on top of 2x Western Digital 2500KS drives on Raid-1, using the motherboard's 780G raid controller, on WinXP. Everything is fine, but the drives are a bit noisy. I am considering buying 2x WD6400AARS disks which are the 640GB slower 'green' drives, but also feature the Advanced Formatting 4KB sectors. This means that for WinXP the partition will have to be aligned to work properly, else there is a performance penalty. There are 2 questions here: The Green drives from WD are all slower and are (according to WD) susceptible to drop-out's from the controller. Has anyone any experience in this matter? Is there a possibility the controller will drop a drive? If so, can i do anything about it? Secondly, western digital gives a utility to perform the alignment on the partition. The thing is, will the utility see the drives in question as the operating system only sees 1 logical disk? I will be making the transition using a cloning tool (most probably norton ghost) unless i don't find a solution or a clear answer, in which case i'll just buy a win 7 license and make a clean install... thx in advance

  Read the article

• Touchpad mouse problem

  - by megatr0n

  Hi all. I have a toshiba satellite and its been behaving weirdly. It only works at the password prompt screen to logon but as soon as I am logged in, it just stops working. Left nor right button clicks are working. I am running vista home. Any pointers on how to go about this? Thanks.

  Read the article

• Dreamweaver Delete Space to Word, Not Word

  - by Don

  There's a built in DW keyboard shortcut (Ctrl + Del) that deletes up to AND INCLUDING the first word to the right. I used to use the ColdFusion Studio app for coding and it would just remove the space UP TO the word (left the word or bracket, or whatever alone.) Any DW users know if this is a setting that can be changed? I'm really used to the old behavior and keep deleting the first word, hitting Ctrl + Z to put it back and then having to manually delete all the spaces to leave the word... Hoping one of you geniuses can help! Thanks, D.

  Read the article

• signed software :: installer -- system software and package installer tool (Apple *.pkg)

  - by fyodor78

  Does anybody know a few details about signed software and /Applications/Utilities/Installer.app? I didn't find more at Wikipedia (https://secure.wikimedia.org/wikipedia/en/wiki/Installer_%28Mac_OS_X%29) and the UNIX-Manual (man 8 installer). I have here a valid signature from iLife 11 Installer.app (http://i.imgur.com/Y3raY.jpg). Does this mean I can be 100% sure that nothing is modified? It means I can trust this PKG because signed by Apple? Or did I get something wrong?

  Read the article

• Time machine not recognizing sparsebundle

  - by Tom

  I've created a sparsebundle just as suggested at http://www.readynas.com/?p=253; however, Time Machine fails to recognize the mounted image. The sparseimage is stored on an external drive, and I already executed: defaults write com.apple.systempreferences TMShowUnsupportedNetworkVolumes 1 I have also verified that the naming format of the sparsebundle is: MachineName_.sparsebundle. I'm running the latest version of Snow Leopard (10.6.7).

  Read the article

• How do I use an internal SSD as a scratch disk for FCP X?

  - by andrewb

  I'm contemplating setting up my MacBook Air as a video editing machine. If I do this, I'll upgrade to a 256 GB SSD, and I should be able to keep around 100 GB or more free for video editing. The video files would of course be stored externally, but save purchasing some expensive Thunderbolt RAID device (which I suppose is gradually becoming more of an option), it will be slow for read/writes. How can I have a set up where I take advantage of my SSD's speed for a scratch disk/cache for FCP X, but still have the TB(s) of storage of externals? I don't want to have to be moving files constantly back and forth, this is about saving time not wasting it.

  Read the article

• Where does vista's Notes gadget store your notes?

  - by D Connors

  I like to use the default notes gadget in vista, and I want to sinchronize my notes between my PC and my laptop. I'm gonna use dropbox, so I just need to know where does the gadget store my notes. I looked inside the Appdata folder and couldn't find the actual notes (only config files). Does anyone know where they are? They have to be stored somewhere, since they are saved even if you close the sidebar. Thanks

  Read the article

• getting pagerank

  - by oneat

  how can I retrieve pagerank of any page indexed by google ? Has google any api or page for this ??

  Read the article

• SQL Server Management Studio Color Schemes?

  - by sunpech

  Is there a way to apply color schemes and themes to SQL Server Management Studio? I really enjoy the ones for Visual Studio 2005/2008/2010 and would love to have something like that. Color Schemes for Visual Studio: Create and share Visual Studio color schemes

  Read the article

• Setting the view of the toolbar to Large icons creates a gap in the Windows 7's taskbar

  - by Boris

  If you add a custom toolbar in the Windows 7 taksbar and set the toolbar view to Large Icons (and the icons in the toolbar are not set to Use small icons), the height of the taskbar unexpectedly increases by around 5 pixels, which makes a rather stupid gap at the bottom of the screen. If the option Use small icons is used for the taskbar appearance, the height of the taskbar is normal. It appears that the programmers at Microsoft were not very meticulous while designing the Windows 7 UI; it is obviously a bug. I was wondering if there is a registry hack to fix this or if anyone knows any solution to the problem, except for the obvious one: "use the small icons"? Thanks.

  Read the article

• OS X Snow Leopard stops processing clicks from Wacom Intuous2

  - by antiver

  I'm using a Wacom Intuos2 graphics tablet in OS X Snow Leopard 10.6.2, which works great, 80% of the time. Every 20 minutes or so, OS X to just start ignoring input from the pen. More specifically, only the pen tip is ignored - the side buttons on the pen still work. Putting the Mac to sleep and waking it back up restores functionality to the pen tip. This is using both of the latest Wacom drivers claiming compatibility with Snow Leopard: versions 6.1.2-5 (Nov 25, 2009) and 6.1.3-3 (Jan 21, 2010). I have no experience with this tablet with other version of OS X / drivers. The tablet works 100% in Windows, which leads to blame either OS X or the OS X drivers.

  Read the article

• Find and free disk space that is unused but unavailable (due to file system error, etc.)

  - by Voyagerfan5761

  Sometimes I get the feeling that if an app such as μTorrent allocates files on my FAT32-formatted flash drive, but then is killed or crashes (as happens more than a few times a month), that space just disappears from my file system. Whether or not that is the case, sometimes I do get a chill from wondering if I've lost hundreds of MB in available storage due to carelessness or malfunctions. Checking my disk with WinDirStat just makes it worse, because I see the huge "<Unknown>" item at the disk root staring at me, eating up well over a gigabyte. It might be FS inefficiency (due to 32 or 64kb sector/cluster size and a lot of tiny files) or it might be a glitch... Is there a tool I can download and run to check my file system and make sure that there aren't any unused allocated blocks on the disk? I want to make sure I'm not losing any disk space to I/O errors, etc.

  Read the article

• Lightning strike causes fast download?

  - by blaine

  Ok, REALLY strange question. My friend says he was downloading a 14 GB file at about 1 mb/s when suddenly there was a lightning strike outside and momentarily the download speed jumped to 10,000,000 GB/s. The file finnished downloading. He even has the screenshot to prove it. I also trust him and don't believe that he would be lying. So my question is: how is this even possible?? Is there just the possibility that the file was about to finish downloading anyway and the lightning strike coincided with a freak download speed calculation error?

  Read the article

• Installed mountain lion, getting a python virtual env error?

  - by user27449

  I recently installed mountain lion (10.8) and when I open up my terminal I get this message: Traceback (most recent call last): File "<string>", line 1, in <module> ImportError: No module named virtualenvwrapper.hook_loader virtualenvwrapper.sh: There was a problem running the initialization hooks. If Python could not import the module virtualenvwrapper.hook_loader, check that virtualenv has been installed for VIRTUALENVWRAPPER_PYTHON=/usr/bin/python and that PATH is set properly. Before I try and fix this, I was hoping someone could guide me as I haven't touched python in a while and I don't want to mess up this installation.

  Read the article

• Windows and Linux applications to show cumulative uploads/downloads for each app, at a glance

  - by jontyc

  I've read few quite a few other threads on SU, but they have been focused on instantaneous/average bandwidths (B/sec) rather than cumulative download/upload totals for a period. Either that or they don't drill down to application level. Resource Monitor in Windows 7 only shows bandwidth. I've just been trying NetLimiter and whereas it can show total uploaded/downloaded, it's a case of having one stats window open per application, as opposed to a table showing all applications at once. Looking for applications for both Windows and Linux (Ubuntu), but they don't need to be the same.

  Read the article

• NVidia ION and /dev/mapper/nvidia_... issues.

  - by Ritsaert Hornstra

  I have an NVidia ION board with 4 SATA ports and want to use that to run a Linux Server (CentOS 5.4). I first hooed up 3 HDs (that will be a RAID5 array) and a forth small boot HD. I first started to use the onboard RAID capability but that does not work correctly under Linux: the raid capacity is not a real RAID but uses lvm to define some arays. After setting the BIOS back to normal SATA mode and whiping the HDs, the first boot harddisk (/dev/sda) is seen as /dev/sda BEFORE mounting and after mounting as /dev/mapper/nvidia_. CentOS is unable to install on it (and grub is not installable on it either). So somehow the harddisk is still seen as if it belongs to some lvm volume. I tried to clean out the HD by issuing a few dd if=/dev/zero of=/dev/sda commands to wipe the starting cylinders and final cylinders but to no avail. Did anyone see this problem and did anyone find a solution? UPDATE When I create only a single ext3 partition on the first HD (/dev/mapper/nvidia_...) no LVM partitions are seen and I can boot from /dev/mapper/nvidia_.... Now the next step is to see how I can get rid of this folly.

  Read the article

• Firefox extension to dinamically change superbar icon, similar to windows live messenger.

  - by D Connors

  With seven's new superbar, windows live messenger is now able to display your status on the bar's icon (and not on the system tray). So that got me thinking, maybe a firefox extension could do something similar. Therefore, here's my question to those who understand the workings and spinning wheels behind firefox extensions: could a firefox extension change the superbar icon to display some useful info? Does the current functionality support it? EDIT: I think my question is not really clear. I just want to know if it's theoritically possible for a firefox addon to change the superbar icon dinamically. For instance, windows live messenger changes the icon acording to your status, and gmail notifier plus changes the icon according to your unread messages count. I'm just wondering if firefox as it is right now supports an extension with that functionality. I know that no current extensions do it, and I'm not looking for a gmail notifier (that was just an example). thanks

  Read the article

• Linux error when resume from RAM

  - by TuxPotato

  The last two times that I have resumed my laptop from sleep, it has hung and given me this set of errors: [drm:atom_op_jump] *ERROR* atombios stuck in loop for more than 1sec aborting [drm:atom_execute_table_locked] *ERROR* atombios stuck executing E692 (len 460, WS 0, PS 4) @0xE6D3 hda_intel: azx_get_responce timeout, switching to single_cmd mode: last cmd=0x01170700 ata6: softreset failed (device not ready) ata4: softreset failed (device not ready) [drm:atom_op_jump] *ERROR* atombios stuck in loop for more than 1sec aborting [drm:atom_execute_table_locked] *ERROR* atombios stuck executing E692 (len 460, WS 0, PS 4) @0xE6D3 The last two messages repeat two more times. The first time this happened, Linux's Magic SysRq worked and did a soft reboot, and after that everything was fine till it went to sleep again. It wakes up and gives me this. Here are the laptop stats: Toshiba Satellite L455D-S5976 AMD Sempron SI-42 Processor 2GB DDR2 RAM HD TruBrite Display ATI Radeon Graphics (integrated) Running Ubuntu 10.10 32 bit I'm not sure about the hard drive, but its a 250GB drive with one NTFS partition, two Hidden NTFS, one Linux Swap, and one Ext4. Can someone tell me whats wrong with my laptop? NOTE: This only happens when I close the screen. My computer doesn't go to sleep with the screen open.

  Read the article

• Windows 7 and laptop overheating

  - by Nikola

  I am using ArchLinux 99% of my working time, and laptop has absolutely no heating problems. But when it comes to using Windows 7, laptop starts heating and one can clearly hear CPU fan working like crazy. I think it has something to do with CPU itself, because on Linux I can simply manipulate with CPU governors (eg. set it to ondemand), but I can't seem to find any similar software to do the same thing as if in Linux. Or, the heating might be caused because of two graphics cards or something? CPU-Z results http://valid.canardpc.com/show_oc.php?id=2310815 Any idea/solution regarding this issue?

  Read the article

• how to insert many similar records in mysql at a time using phpmyadmin?

  - by Networker

  we know that we can insert multiple records at a time using this query: INSERT INTO `TABLE1` (`First`,`Last`) VALUES ('name1','surname1'), ('name2','surname2'), ('name3','surname3'), ('name4','surname4'); but what if we want to add 1000 similar records as above (name*,surname*) do we have to write down all the records or we can use something like wildcard? or is there any other solution using mysql?

  Read the article

• Why is my own e-mail address not listed in the To field?

  - by Sammy

  I have received a suspicious e-mail. I am not affiliated with the company mentioned in the e-mail body, or the signer. However, I have been using the app they mention in the e-mail. They are inviting me to a Beta test. But the e-mail is not by the original author of the app. But I'm thinking they might have hired an external company to do this version of the app. There is a link to a TestFlight page. So I'm not sure what to make of this. Now this is what mainly arose my attention. From: Anders Bergman <[email protected]> To: Bon Support Cc: Subject: Test av nya BBK för Android This is how it shows up in Outlook 2010. The "To" field is addressed to "Bon Support" and when I double-click on that I see [email protected]. I can assure you that none of these are my e-mail addresses. So where the heck is my own e-mail address? How could I have received this if it was addressed to someone else? If not spammers and skimmers and other criminals, who else is using this practice and why? And how can I tell now to what e-mail account I received this? I have more than one account set up in Outlook.

  Read the article

• Legality of ripping DVD audio

  - by Smashery

  I want to buy several live music DVDs, but I also want to be able to put the music in my playlists. It seems ridiculous that I should also have to buy the Live CD version. Is it legal (particularly under Australian law) to rip the audio?

  Read the article

• reset all apple osx 10.6 fonts

  - by chris hough

  over time I have installed a bunch of fonts that are either not properly licensed or I have not documentented as to where I got them from. Is there a way to reset all of the installed fonts back to the default install and remove all of the fonts I have installed? I have done some research and have not come up with a solid way to tackle this. Thank you for your help everyone :)

  Read the article

• Detecting source of memory usage on a Linux box

  - by apeace

  I have a toy Linux box with 256mb RAM running Ubuntu 10.04.1 LTS. Here is the output of free -m: total used free shared buffers cached Mem: 245 122 122 0 19 64 -/+ buffers/cache: 38 206 Swap: 511 0 511 Unless I'm reading this wrong, 122mb is being used and only 84mb of that is disk cache. Here are all processes I'm running sorted by memory usage (ps -eo pmem,pcpu,rss,vsize,args | sort -k 1 -r): %MEM %CPU RSS VSZ COMMAND 5.0 0.0 12648 633140 node /home/node/main/sites.js 1.5 0.0 3884 251736 /usr/sbin/console-kit-daemon --no-daemon 1.3 0.0 3328 77108 sshd: apeace [priv] 0.9 0.0 2344 19624 -bash 0.7 0.0 1776 23620 /sbin/init 0.6 0.0 1624 77108 sshd: apeace@pts/0 0.6 0.0 1544 9940 redis-server /etc/redis/redis.conf 0.6 0.0 1524 25848 /usr/sbin/ntpd -p /var/run/ntpd.pid -g -u 103:105 0.5 0.0 1324 119880 rsyslogd -c4 0.4 0.0 1084 49308 /usr/sbin/sshd 0.4 0.0 1028 44376 /usr/sbin/exim4 -bd -q30m 0.3 0.0 904 6876 ps -eo pmem,pcpu,rss,vsize,args 0.3 0.0 888 21124 cron 0.3 0.0 868 23472 dbus-daemon --system --fork 0.2 0.0 732 19624 -bash 0.2 0.0 628 6128 /sbin/getty -8 38400 tty1 0.2 0.0 628 16952 upstart-udev-bridge --daemon 0.2 0.0 564 16800 udevd --daemon 0.2 0.0 552 16796 udevd --daemon 0.2 0.0 548 16796 udevd --daemon 0.0 0.0 0 0 [xenwatch] 0.0 0.0 0 0 [xenbus] 0.0 0.0 0 0 [sync_supers] 0.0 0.0 0 0 [netns] 0.0 0.0 0 0 [migration/3] 0.0 0.0 0 0 [migration/2] 0.0 0.0 0 0 [migration/1] 0.0 0.0 0 0 [migration/0] 0.0 0.0 0 0 [kthreadd] 0.0 0.0 0 0 [kswapd0] 0.0 0.0 0 0 [kstriped] 0.0 0.0 0 0 [ksoftirqd/3] 0.0 0.0 0 0 [ksoftirqd/2] 0.0 0.0 0 0 [ksoftirqd/1] 0.0 0.0 0 0 [ksoftirqd/0] 0.0 0.0 0 0 [ksnapd] 0.0 0.0 0 0 [kseriod] 0.0 0.0 0 0 [kjournald] 0.0 0.0 0 0 [khvcd] 0.0 0.0 0 0 [khelper] 0.0 0.0 0 0 [kblockd/3] 0.0 0.0 0 0 [kblockd/2] 0.0 0.0 0 0 [kblockd/1] 0.0 0.0 0 0 [kblockd/0] 0.0 0.0 0 0 [flush-202:1] 0.0 0.0 0 0 [events/3] 0.0 0.0 0 0 [events/2] 0.0 0.0 0 0 [events/1] 0.0 0.0 0 0 [events/0] 0.0 0.0 0 0 [crypto/3] 0.0 0.0 0 0 [crypto/2] 0.0 0.0 0 0 [crypto/1] 0.0 0.0 0 0 [crypto/0] 0.0 0.0 0 0 [cpuset] 0.0 0.0 0 0 [bdi-default] 0.0 0.0 0 0 [async/mgr] 0.0 0.0 0 0 [aio/3] 0.0 0.0 0 0 [aio/2] 0.0 0.0 0 0 [aio/1] 0.0 0.0 0 0 [aio/0] Now, I know that ps is not the best for viewing process memory usage, but that's because it tends to report more memory than is actually being used...meaning no matter how you look at it all my processes combined shouldn't be using near 122mb, even if you account for the disk cache. What's more, memory usage is growing all the time. I've had to restart my server once a week, because once my 256mb fills up it starts swapping, which it wouldn't do just for disk cache. Shouldn't there be some way for me to see the culprit?! I'm new to server admin, so please if there's something obvious I'm overlooking point it out to me. Just for good measure, the output of cat /proc/meminfo: MemTotal: 251140 kB MemFree: 124604 kB Buffers: 20536 kB Cached: 66136 kB SwapCached: 0 kB Active: 65004 kB Inactive: 37576 kB Active(anon): 15932 kB Inactive(anon): 164 kB Active(file): 49072 kB Inactive(file): 37412 kB Unevictable: 0 kB Mlocked: 0 kB SwapTotal: 524284 kB SwapFree: 524284 kB Dirty: 8 kB Writeback: 0 kB AnonPages: 15916 kB Mapped: 10668 kB Shmem: 188 kB Slab: 18604 kB SReclaimable: 10088 kB SUnreclaim: 8516 kB KernelStack: 536 kB PageTables: 1444 kB NFS_Unstable: 0 kB Bounce: 0 kB WritebackTmp: 0 kB CommitLimit: 649852 kB Committed_AS: 64224 kB VmallocTotal: 34359738367 kB VmallocUsed: 752 kB VmallocChunk: 34359737600 kB DirectMap4k: 262144 kB DirectMap2M: 0 kB EDIT: I had misinterpreted the meaning of free -m at first. But even so: the important thing is that my OS eventually begins to use swap memory if I don't restart my server, which disk caching wouldn't do. So where do I look to see what is using all this memory?

  Read the article

< Previous Page | 647 648 649 650 651 652 653 654 655 656 657 658  | Next Page >