Search Results

Search found 18379 results on 736 pages for 'output buffering'.

Page 654/736 | < Previous Page | 650 651 652 653 654 655 656 657 658 659 660 661  | Next Page >

  • RHEL 6.x on Rackspace Cloud and Dedicated hardware experiencing Redis Timeouts

    - by zhallett
    I just recently set up a mixture of RHEL 6.1 Rackspace cloud hosts and RHEL 6.2 dedicated hosts using Rackconnect. I am experiencing intermittent Redis timeouts from within our Rails 3.2.8 app with Redis 2.4.16 running on the RHEL 6.2 dedicated hosts. There is no network latency or packet loss. Also there are no errors on any interfaces on our cloud or dedicated servers or on the managed firewall from Rackspace. When Redis timesout, there is nothing logged within redis even though it is set up to do debug logging. The only error we receive is from Airbrake saying there was a Redis timeout. Network topology: RHEL 6.1 cloud hosts <--> Alert logic IDS <--> Cisco ASA 5510 <--> RHEL 6.2 dedicated hosts (web nodes) (two way NAT) (db hosts running redis) Ping from db host to web host: 64 bytes from 10.181.230.180: icmp_seq=998 ttl=64 time=0.520 ms 64 bytes from 10.181.230.180: icmp_seq=999 ttl=64 time=0.579 ms 64 bytes from 10.181.230.180: icmp_seq=1000 ttl=64 time=0.482 ms --- web1.xxxxxx.com ping statistics --- 1000 packets transmitted, 1000 received, 0% packet loss, time 999007ms rtt min/avg/max/mdev = 0.359/0.535/5.684/0.200 ms Ping from web host to db host: 64 bytes from 192.168.100.26: icmp_seq=998 ttl=64 time=0.544 ms 64 bytes from 192.168.100.26: icmp_seq=999 ttl=64 time=0.452 ms 64 bytes from 192.168.100.26: icmp_seq=1000 ttl=64 time=0.529 ms --- data1.xxxxxx.com ping statistics --- 1000 packets transmitted, 1000 received, 0% packet loss, time 999017ms rtt min/avg/max/mdev = 0.358/0.499/6.120/0.201 ms Redis config: daemonize yes pidfile /var/run/redis/6379/redis_6379.pid port 6379 timeout 0 loglevel debug logfile /var/lib/redis/log syslog-enabled yes syslog-ident redis-6379 syslog-facility local0 databases 16 save 900 1 save 300 10 save 60 10000 rdbcompression yes dbfilename dump-6379.rdb dir /var/lib/redis maxclients 10000 maxmemory-policy volatile-lru maxmemory-samples 3 appendfilename appendonly-6379.aof appendfsync everysec no-appendfsync-on-rewrite no auto-aof-rewrite-percentage 100 auto-aof-rewrite-min-size 64mb slowlog-log-slower-than 10000 slowlog-max-len 1024 vm-enabled no vm-swap-file /tmp/redis.swap vm-max-memory 0 vm-page-size 32 vm-pages 134217728 vm-max-threads 4 hash-max-zipmap-entries 512 hash-max-zipmap-value 64 list-max-ziplist-entries 512 list-max-ziplist-value 64 set-max-intset-entries 512 zset-max-ziplist-entries 128 zset-max-ziplist-value 64 activerehashing yes Redis-cli info: redis-cli info redis_version:2.4.16 redis_git_sha1:00000000 redis_git_dirty:0 arch_bits:64 multiplexing_api:epoll gcc_version:4.4.6 process_id:4174 uptime_in_seconds:79346 uptime_in_days:0 lru_clock:1064644 used_cpu_sys:13.08 used_cpu_user:19.81 used_cpu_sys_children:1.56 used_cpu_user_children:7.69 connected_clients:167 connected_slaves:0 client_longest_output_list:0 client_biggest_input_buf:0 blocked_clients:6 used_memory:15060312 used_memory_human:14.36M used_memory_rss:22061056 used_memory_peak:15265928 used_memory_peak_human:14.56M mem_fragmentation_ratio:1.46 mem_allocator:jemalloc-3.0.0 loading:0 aof_enabled:0 changes_since_last_save:166 bgsave_in_progress:0 last_save_time:1352823542 bgrewriteaof_in_progress:0 total_connections_received:286 total_commands_processed:507254 expired_keys:0 evicted_keys:0 keyspace_hits:1509 keyspace_misses:65167 pubsub_channels:0 pubsub_patterns:0 latest_fork_usec:690 vm_enabled:0 role:master db0:keys=6,expires=0 edit 1: add redis-cli info output

    Read the article

  • "vagrant up" fails with "NS_ERROR_CALL_FAILED" error [on hold]

    - by TahitiPetey
    I am following the basic "Getting Started" guide: http://docs.vagrantup.com/v2/getting-started/index.html I ran vagrant init <etc> followed by vagrant up, but it fails with "NS_ERROR_CALL_FAILED" error. Then by enabling debug logging with VAGRANT_LOG=debug vagrant up, I get the following error output: ERROR vagrant: /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/plugins/providers/virtualbox/driver/base.rb:316:in `execute' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/plugins/providers/virtualbox/driver/version_4_2.rb:165:in `import' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/plugins/providers/virtualbox/action/import.rb:15:in `call' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/lib/vagrant/action/warden.rb:34:in `call' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/lib/vagrant/action/builtin/handle_box_url.rb:72:in `call' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/lib/vagrant/action/warden.rb:34:in `call' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/plugins/providers/virtualbox/action/check_accessible.rb:18:in `call' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/lib/vagrant/action/warden.rb:34:in `call' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/lib/vagrant/action/runner.rb:61:in `block in run' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/lib/vagrant/util/busy.rb:19:in `busy' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/lib/vagrant/action/runner.rb:61:in `run' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/lib/vagrant/action/builtin/call.rb:51:in `call' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/lib/vagrant/action/warden.rb:34:in `call' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/lib/vagrant/action/builtin/config_validate.rb:25:in `call' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/lib/vagrant/action/warden.rb:34:in `call' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/plugins/providers/virtualbox/action/check_virtualbox.rb:17:in `call' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/lib/vagrant/action/warden.rb:34:in `call' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/lib/vagrant/action/builder.rb:116:in `call' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/lib/vagrant/action/runner.rb:61:in `block in run' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/lib/vagrant/util/busy.rb:19:in `busy' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/lib/vagrant/action/runner.rb:61:in `run' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/lib/vagrant/machine.rb:147:in `action' /Applications/Vagrant/embedded/gems/gems/vagrant-1.2.2/lib/vagrant/batch_action.rb:63:in `block (2 levels) in run' INFO interface: error: There was an error while executing `VBoxManage`, a CLI used by Vagrant for controlling VirtualBox. The command and stderr is shown below. Command: ["import", "/Users/me/.vagrant.d/boxes/precise32/virtualbox/box.ovf"] Stderr: 0%...10%...20%...30%...40%...50%...60%...70%...80%...90%...100% Interpreting /Users/me/.vagrant.d/boxes/precise32/virtualbox/box.ovf... OK. 0%... Progress object failure: NS_ERROR_CALL_FAILED My system setup info: Vagrant 1.2.2 VirtualBox 4.2.14 (Also tried 4.2.10, same error) Mac OSX 10.8.3

    Read the article

  • Debugging IO limitation

    - by Martin F
    I have a Fedora box with some severe IO limitations which I have no idea how to debug. The server has a Areca Technology Corp. ARC-1130 12-Port PCI-X to SATA RAID Controller with 12 7200 RPM 1.5 TB disks and a Marvell Technology Group Ltd. 88E8050 PCI-E ASF Gigabit Ethernet Controller. uname -a output: 2.6.32.11-99.fc12.x86_64 #1 SMP Mon Apr 5 19:59:38 UTC 2010 x86_64 x86_64 x86_64 GNU/Linux The server is a file server running Nginx with the stub status module enabled, so I can see the current amount of connections. The problem present itself when I have a high number of simultaneous connections in a writing state. Usually around 350, at this very moment it's at 590 and the server is almost unusable and stuck at 230mbit/s. If I run stop and hit 1 to see CPU core usages I have all 4 cores with around 99% io wait, if I run iotop the nginx workers are the only processes producing any read load, currently at around 25MB/s. I have each of the workers bound to their own core. Initially I figured it was just the disks being bugged. But I've run fscheck and smartmontools checks and found no errors. I also ran an iozone test which you can see the result of here: http://www.pastie.org/951667.txt?key=fimcvljulnuqy2dcdxa Additionally, when the amount of connections are low I have no problem getting a good speed. If I wget over the local network it easily hits 60MB/sec. Right now I just tried putting a file in /dev/shm, then I symlinked a file from the public dir to it and used wget over the local network and only got 50KB/s. Also, if I try to cp /dev/shm/test /root/test it quickly copies around 740MB and then slows down HEAVILY. Again with iotop reporting 99% iowait. I'm not really sure how to go about figuring out what the problems are. It could be a natural disk limitation but then the file from /dev/shm ought to transfer so it seems there's a network limit, but that's fine when there's not many connections. Perhaps it's a TCP stack problem but I really have no idea how to check that. Any suggestions on how to proceed with debugging would be very welcome. If additional information is required then let me know and I'll try to get it. Thanks.

    Read the article

  • Vagrant - Failed login, ssh not set up

    - by motleydev
    This question is two fold because somewhere in my attempts to solve the problem, I created a new one. First: I was trying to vagrant up using a Vagranfile based on the standard hashicorp/precise32 box. Everything worked up until default: SSH auth method: private key where it would eventually time out. Enabling gui in the Vagrantfile showed that the machine never actually logs in. I can use the standard user/pass and log in from that point but the vagrant up process still remains at that prior status. Here's where my understanding might be a little dim. I've tried setting auth method from the insecure_pass_key to my root ~/.ssh/id_rsa or whichever one I wanted to use. I'm not entirely sure where to put a copy of the public key or my authorized keys file. I've got a .vagrant.d folder in my user dir (I'm on OSX) which seems to contain the box images. I've got a .vagrant folder in my directory with the Vagrantfile which seems to contain the specific machine I am building off of. I've tried pouring over the docs and forums but I seem to be missing a key concept here. And Now: After a host of tips/tricks such as rolling back by VirtualBox install, uninstalling/reinstalling Vagrant and VritualBox several times, when I try to run vagrant ssh-config with a Vagrantfile based on the same hashicorp/precise32 it says that the box is not enabled for SSH. Specifically, this error: The provider for this Vagrant-managed machine is reporting that it is not yet ready for SSH. Depending on your provider this can carry different meanings. Make sure your machine is created and running and try again. Additionally, check the output of `vagrant status` to verify that the machine is in the state that you expect. If you continue to get this error message, please view the documentation for the provider you're using. So now I am slightly up a creek. Any help would be appreciated if not just clarifying a concept. Some pertinent info: I'm on OSX Maverics Due to the fact I'm running a dual HD system with system files on one HD and user files on another, my permissions are a little wonky and VBoxManage will only let me run commands via Sudo - not sure if it's pertinent - but maybe. I have no idea what I'm doing. That part is perhaps more important.

    Read the article

  • Make error in installing Math support for MediaWiki

    - by Masi
    How can you solve the following Make error in installing MediaWiki? ... /local/lib/site_perl . /etc/perl /usr/local/lib/perl/5.10.0 /usr/local/share/perl/5.10.0 /usr/lib/perl5 /usr/share/perl5 /usr/lib/perl/5.10 /usr/share/perl/5.10 /usr/local/lib/site_perl .) at t/maint/php-tag.t line 8. BEGIN failed--compilation aborted at t/maint/php-tag.t line 8. # Looks like your test died before it could output anything. t/maint/php-tag..........dubious Test returned status 255 (wstat 65280, 0xff00) t/maint/unix-newlines....ok Failed Test Stat Wstat Total Fail List of Failed ------------------------------------------------------------------------------- t/00-test.t 127 32512 ?? ?? ?? t/inc/Database.t 127 32512 ?? ?? ?? t/inc/Global.t 127 32512 ?? ?? ?? t/inc/IP.t 127 32512 ?? ?? ?? t/inc/ImageFunctions.t 127 32512 ?? ?? ?? t/inc/Language.t 127 32512 ?? ?? ?? t/inc/Licenses.t 127 32512 ?? ?? ?? t/inc/LocalFile.t 127 32512 ?? ?? ?? t/inc/Parser.t 127 32512 ?? ?? ?? t/inc/Revision.t 127 32512 ?? ?? ?? t/inc/Sanitizer.t 127 32512 ?? ?? ?? t/inc/Search.t 127 32512 ?? ?? ?? t/inc/Title.t 127 32512 ?? ?? ?? t/inc/Xml.t 127 32512 ?? ?? ?? t/maint/php-lint.t 254 65024 966 966 1-966 t/maint/php-tag.t 255 65280 ?? ?? ?? Failed 16/19 test scripts. 966/4248 subtests failed. Files=19, Tests=4248, 46 wallclock secs (33.15 cusr + 10.38 csys = 43.53 CPU) Failed 16/19 test programs. 966/4248 subtests failed. make: *** [test] Error 255

    Read the article

  • Forwarding RDP via a Linux machine using iptables: Not working

    - by Nimmy Lebby
    I have a Linux machine and a Windows machine behind a router that implements NAT (the diagram might be overkill, but was fun to make): I am forwarding RDP port (3389) on the router to the Linux machine because I want to audit RDP connections. For the Linux machine to forward RDP traffic, I wrote these iptables rules: iptables -t nat -A PREROUTING -p tcp --dport 3389 -j DNAT --to-destination win-box iptables -A FORWARD -p tcp --dport 3389 -j ACCEPT The port is listening on the Windows machine: C:\Users\nimmy>netstat -a Active Connections Proto Local Address Foreign Address State (..snip..) TCP 0.0.0.0:3389 WIN-BOX:0 LISTENING (..snip..) And the port is forwarding on the Linux machine: # tcpdump port 3389 tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on eth0, link-type EN10MB (Ethernet), capture size 65535 bytes 01:33:11.451663 IP shieldsup.grc.com.56387 > linux-box.myapt.lan.ms-wbt-server: Flags [S], seq 94663035, win 8192, options [mss 1460], length 0 01:33:11.451846 IP shieldsup.grc.com.56387 > win-box.myapt.lan.ms-wbt-server: Flags [S], seq 94663035, win 8192, options [mss 1460], length 0 However, I am not getting any successful RDP connections from the outside. The port is not even responding: C:\Users\outside-nimmy>telnet example.com 3389 Connecting To example.com...Could not open connection to the host, on port 3389: Connect failed Any ideas? Update Per @Zhiqiang Ma, I looked at nf_conntrack proc file during a connection attempt and this is what I see (192.168.3.1 = linux-box, 192.168.3.5 = win-box): # cat /proc/net/nf_conntrack | grep 3389 ipv4 2 tcp 6 118 SYN_SENT src=4.79.142.206 dst=192.168.3.1 sport=43142 dport=3389 packets=6 bytes=264 [UNREPLIED] src=192.168.3.5 dst=4.79.142.206 sport=3389 dport=43142 packets=0 bytes=0 mark=0 secmark=0 zone=0 use=2 2nd update Got tcpdump on the router and it seems that win-box is sending an RST packet: 21:20:24.767792 IP shieldsup.grc.com.45349 > linux-box.myapt.lan.3389: S 19088743:19088743(0) win 8192 <mss 1460> 21:20:24.768038 IP shieldsup.grc.com.45349 > win-box.myapt.lan.3389: S 19088743:19088743(0) win 8192 <mss 1460> 21:20:24.770674 IP win-box.myapt.lan.3389 > shieldsup.grc.com.45349: R 721745706:721745706(0) ack 755785049 win 0 Why would Windows be doing this?

    Read the article

  • User given a login prompt when closing Word documents after viewing them in IE7

    - by Martin Owen
    When using IE7 to view Word documents on our CRM system (an ASP.NET 2.0 application running on Windows Server 2003 and IIS 6 and using Windows authenticaton) I'm finding that a prompt appears when the user closes the document. The Word document is originally opened by clicking a link in the CRM system. Are there permissions that I can set on the folder containing the Word documents to prevent this prompt? I've already tried only allowing the Read permission for the Users group (I've left Administrators with Full Control.) If there's another solution to this without using permissions please let me know. UPDATE: I ran Fiddler as suggested by JD and here is the output from the two responses after the request for the document. The first seems to be a DAV response and the second is the authentication request. How do I prevent the DAV response and just return the .doc on the server? OPTIONS / HTTP/1.1 Translate: f User-Agent: Microsoft Data Access Internet Publishing Provider Protocol Discovery Host: <REMOVED> Content-Length: 0 Connection: Keep-Alive Pragma: no-cache X-NovINet: v1.2 HTTP/1.1 200 OK Date: Thu, 18 Feb 2010 13:37:36 GMT Server: Microsoft-IIS/6.0 X-Powered-By: ASP.NET MS-Author-Via: DAV Content-Length: 0 Accept-Ranges: none DASL: <DAV:sql> DAV: 1, 2 Public: OPTIONS, TRACE, GET, HEAD, DELETE, PUT, POST, COPY, MOVE, MKCOL, PROPFIND, PROPPATCH, LOCK, UNLOCK, SEARCH Allow: OPTIONS, TRACE, GET, HEAD, COPY, PROPFIND, SEARCH, LOCK, UNLOCK Cache-Control: private ------------------------------------------------------------------ OPTIONS /docs/ZONE%20100-105.doc HTTP/1.1 Translate: f User-Agent: Microsoft Data Access Internet Publishing Provider Protocol Discovery Host: <REMOVED> Content-Length: 0 Connection: Keep-Alive Pragma: no-cache X-NovINet: v1.2 HTTP/1.1 401 Unauthorized Content-Length: 83 Content-Type: text/html Server: Microsoft-IIS/6.0 WWW-Authenticate: Basic realm="<REMOVED>" X-Powered-By: ASP.NET Date: Thu, 18 Feb 2010 13:37:36 GMT ------------------------------------------------------------------ UPDATE 2: I found a potential workaround for the problem via this post: http://forums.iis.net/p/1149091/1868317.aspx. I moved all of the documents that are being requested into a folder outside of the web root, and created a virtual directory for it (also outside of the web root). When I followed a link to one of the documents in IE and then closed the document I wasn't presented with a login prompt. I should point out that I'm not using FPSE, unlike the person in the forum post. Ideally I don't want to have to put the documents in a separate virtual directory, but this is the simplest solution I've found so far.

    Read the article

  • Mysteriously empty $_POST array

    - by Lex
    Hi all! I have the following HTML/PHP page: <?php if(empty($_SERVER['CONTENT_TYPE'])) { $type = "application/x-www-form-urlencoded"; $_SERVER['CONTENT_TYPE'] = $type; } echo "<pre>"; var_dump($_POST); var_dump(file_get_contents("php://input")); echo "</pre>"; ?> <form method="post" action="test.php"> <input type="text" name="test[1]" /> <input type="text" name="test[2]" /> <input type="text" name="test[3]" /> <input type="submit" name="action" value="Go" /> </form> As you can see, the form will submit and the expected output is a POST array with one array in it containing the filled in values and one entry "action" with the value "Go" (the button). However, no matter what values I enter in the fields; the result is always: array(2) { ["test"]=> string(0) "" ["action"]=> string(2) "Go" } string(16) "test=&action=Go&" Somehow, the array named test is emptied, the "action" variable does make it through. I've used the Live HTTP Headers extension for Firefox to check whether the POST fields get submitted, and they do. The relevant information from Live HTTP Headers (with a, b and c filled in as values in the textboxes): Content-Type: application/x-www-form-urlencoded Content-Length: 51 test%5B1%5D=a&test%5B2%5D=b&test%5B3%5D=c&action=Go Does anybody have any idea as to why this is happening? I'm freaking out on this one, it has cost me so much time already... EDIT: We've tried this on different servers, on Windows boxes it does work, on the Ubuntu server with PHP version 5.2.4 (with Suhosin), it doesn't. It even works on a different server, also with Ubuntu and the same PHP version, also with Suhosin installed.

    Read the article

  • FTP not listing files behind firewall (setsockopt (ignored): Permission denied)

    - by KennyDs
    We are developing a Magento application that has a module that works with FTP. Today we deployed this on the testing environment which is setup in the following way: Gateway server which has the following iptables rules: # iptables -L -n -v Chain INPUT (policy ACCEPT 2 packets, 130 bytes) pkts bytes target prot opt in out source destination 0 0 ACCEPT all -- lo * 0.0.0.0/0 0.0.0.0/0 165 13720 ACCEPT all -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED Chain FORWARD (policy ACCEPT 7 packets, 606 bytes) pkts bytes target prot opt in out source destination 0 0 ACCEPT all -- eth1 eth0 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 15 965 ACCEPT all -- eth0 eth1 0.0.0.0/0 0.0.0.0/0 0 0 REJECT all -- eth1 eth1 0.0.0.0/0 0.0.0.0/0 reject-with icmp-port-unreachable Chain OUTPUT (policy ACCEPT 126 packets, 31690 bytes) pkts bytes target prot opt in out source destination These are set at runtime via the following bash script: #!/bin/sh PATH=/usr/sbin:/sbin:/bin:/usr/bin # # delete all existing rules. # iptables -F iptables -t nat -F iptables -t mangle -F iptables -X # Always accept loopback traffic iptables -A INPUT -i lo -j ACCEPT # Allow established connections, and those not coming from the outside iptables -A INPUT -m state --state ESTABLISHED,RELATED -j ACCEPT iptables -A FORWARD -i eth1 -o eth0 -m state --state ESTABLISHED,RELATED -j ACCEPT # Allow outgoing connections from the LAN side. iptables -A FORWARD -i eth0 -o eth1 -j ACCEPT # Masquerade. iptables -t nat -A POSTROUTING -o eth1 -j MASQUERADE # Don't forward from the outside to the inside. iptables -A FORWARD -i eth1 -o eth1 -j REJECT # Enable routing. echo 1 > /proc/sys/net/ipv4/ip_forward The gateway server is connected to the WAN via eth1 and is connected to the internal network via eth0. One of the servers from eth1 has the following problem when trying to list files over ftp: $ ftp -vd myftpserver.com Connected to myftpserver.com 220 Welcome to MY FTP Server ftp: setsockopt: Bad file descriptor Name (myftpserver.com:magento): XXXXXXXX ---> USER XXXXXXXX 331 User XXXXXXXX, password please Password: ---> PASS XXXX 230 Password Ok, User logged in ---> SYST 215 UNIX Type: L8 Remote system type is UNIX. Using binary mode to transfer files. ftp> ls ftp: setsockopt (ignored): Permission denied ---> PORT 192,168,19,15,135,75 421 Service not available, remote server has closed connection When I try listing the files in passive mode, same result. When I run the same command on the gateway server, everything works fine so I believe that the issue is happening because of the iptables rules not forwarding properly. Does anyone have an idea which rule I need to add to make this work?

    Read the article

  • T60 Screen/LCD gets black after some minutes with a highpitched sound rising and fading

    - by Edward De Leau
    Just now my T60 screen got "black" (so no display). On my second monitor: no problems so the vga output works. symptom: Screen blanks / no display but works on second monitor steps to reproduce: - boot - wait (it does not matter what you do you do not have to login or anything) - (now the monitor of the laptop slowly begins to make a ssssssssHHHHHHHHHHHHHHHHHWOEOEssssssss noice of about 10 seconds) - right after the sounds ends the monitor gets black times seem to be the same each time. software: installed no new software before/after, running zone alarm and antivirus. other: it does not feel hot in any place, there dont seem to be running processes with strange behaviour. warranty: out of warranty what was i doing: typing text on a website and doing some php coding in a text editor. Anyone any idea what I can do here other than buy a new laptop? / does it sound familiar to known cases? update: * exactly the same problem: http://forums.lenovo.com/t5/T61-and-prior-T-series-ThinkPad/T60-Screen-Blackout/m-p/288772 and the second poster (garyj) here: http://forums.lenovo.com/t5/T61-and-prior-T-series-ThinkPad/Black-Screen-on-T60/m-p/235053#M48627 and here: "i have that same problem. i replaced the CCRL on mine and it works fine when the screen is not screwed in. once the frame of the LCD screen (metal portion) touches the metal on the laptop which holds the screen the screen goes black. If the metal is touching the screen when you boot up it boots up with it being very dimmly lit. " from http://forums.lenovo.com/t5/T61-and-prior-T-series-ThinkPad/T60-screen-problems/m-p/205047#M44995 (it seems replacing the lcd is no use, he tried it 3 times). same problem: http://forums.lenovo.com/t5/T61-and-prior-T-series-ThinkPad/T60-black-screen/m-p/80604#M25914 Hmmm... not handy 3 or 4 months ago I ordered and installed a new fan. Now the LCD. Which does not seem the core isse but some electric issue so it seems replacing the LCD is not the thing todo here. I have the following question: If it is not the LCD that needs to be replaced (see other threads) which parts can I order to fix this? Has anyone got any information which could lead me to identify the issue? I have read replacing the "inverter" AND the "backlightning" would that make sense?

    Read the article

  • grep simply fails when used on a few files

    - by Reid
    I've been trying for about the past 30 minutes to get this to work properly. grep is not exactly the most difficult thing to use, so I'm somewhat baffled as to why this won't work. The files I'm trying to use grep on are simple XHTML log files. Their names are in the format [email protected], though I don't think that should matter, and inside is simple XHTML. I copied one such log file to be testfile so you can see the output of some commands and why it's baffling to me: [~/.chatlogs_windows/dec] > whoami reid [~/.chatlogs_windows/dec] > type grep grep is /bin/grep [~/.chatlogs_windows/dec] > uname -a Linux reid-pc 2.6.35-22-generic #33-Ubuntu SMP Sun Sep 19 20:32:27 UTC 2010 x86_64 GNU/Linux [~/.chatlogs_windows/dec] > head -1 /etc/issue Linux Mint 10 Julia [~/.chatlogs_windows/dec] > ls -Alh | grep testfile -rw-r--r-- 1 reid reid 63K 2011-01-10 12:45 testfile [~/.chatlogs_windows/dec] > tail -3 testfile </body> </html> [~/.chatlogs_windows/dec] > file testfile testfile: XML document text [~/.chatlogs_windows/dec] > grep html testfile [~/.chatlogs_windows/dec] > grep body testfile [~/.chatlogs_windows/dec] > grep "</html>" testfile [~/.chatlogs_windows/dec] > grep "</body>" testfile [~/.chatlogs_windows/dec] > cat testfile | grep html [~/.chatlogs_windows/dec] > cat testfile | wc -l 231 [~/.chatlogs_windows/dec] > cat testfile | tail -3 </body> </html> [~/.chatlogs_windows/dec] > chmod a+rw testfile && ls -Alh | grep testfile -rw-rw-rw- 1 reid reid 63K 2011-01-10 12:45 testfile [~/.chatlogs_windows/dec] > grep html testfile That's what I'm attempting to do. I want to just use grep -ri query . in ~/.chatlogs_windows, which normally works perfectly for me... but for some reason, it completely fails at going through these files. If it matters, I copied these files off of my Windows 7 partition. But I chown'd them and gave myself all the appropriate permissions, and other programs (like cat) seem to read them just fine. I also copied testfile to testfile_unix and converted the line endings and tried that, but it didn't work either. I'm using zsh, but I tried it on bash and that failed too. Also, grep works normally: I tried it out on my documents folder and it worked flawlessly. If you need any more information, just let me know. I tried googling around, but I found no reason for grep to simply not work. Thanks in advance.

    Read the article

  • Apache works on http and https, SVN only on http

    - by user27880
    I asked a question about this before, and got most of it fixed. If I switch off https redirect and go to http://mydomain.com/svn/test0, I get the authentication window popping up, and I can enter my AD credentials, and bingo. Switching https redirect back on, if I go to http://mydomain.com I am automatically redirected to https, which is what I want, and the 'CerntOS test page' pops up. Perfect. The problem occurs when I want to go to one of my test repos via https. Here is my httpd.conf file, with confidential information suitably hosed... === NameVirtualHost *:80 <VirtualHost *:80> ServerAdmin [email protected] ServerName svn.mycompany.com ErrorLog logs/subversion-error_log CustomLog logs/subversion-access_log common Redirect permanent / https://svn.mycompany.com </VirtualHost> <VirtualHost svn.mycompany.com:443> SSLEngine On SSLCertificateFile /etc/httpd/ssl/wildcard.mycompany.com.crt SSLCertificateKeyFile /etc/httpd/ssl/wildcard.mycompany.com.key SSLCertificateChainFile /etc/httpd/ssl/intermediate.crt ServerName svn.mycompany.com ServerAdmin [email protected] ErrorLog logs/subversion-error_log CustomLog logs/subversion-access_log common <Location /svn> DAV svn SVNParentPath /usr/local/subversion SVNListParentPath off AuthName "Subversion Repositories" # NT Logon Details Require valid-user AuthBasicProvider file ldap AuthType Basic AuthzLDAPAuthoritative off AuthUserFile /etc/httpd/conf/svnpasswd AuthName "Subversion Server II" AuthLDAPURL "ldap://our-pdc:389/OU=Company Name,DC=com,DC=co,DC=uk?sAMAccountName?sub?(objectClass=*)" AuthLDAPBindDN "DOMAIN\subversion" AuthLDAPBindPassword XXXXXXX AuthzSVNAccessFile /etc/httpd/conf/svnaccessfile </Location> </VirtualHost> === Now, in ssl_error_log, I get === ==> /etc/httpd/logs/ssl_error_log <== [Fri Nov 01 16:07:55 2013] [error] [client XXX.XXX.XXX.XXX] File does not exist: /var/www/html/svn === This comes from the DocumentRoot directive further up the httpd.conf file, which of course points to /var/www/html. I know that this location is wrong, but how can I get SVN to serve the repo? I tried an Alias directive as so .. Alias /svn /usr/local/subversion .. but this didn't work. I tried to alter the Location directive. That didn't work either. Can someone help? I sense that this is so close to being solved ... Thanks. Edit: apachectl -S output: [root@svn conf]# apachectl -S VirtualHost configuration: 127.0.0.1:443 svn.mycompany.com (/etc/httpd/conf/httpd.conf:1020) wildcard NameVirtualHosts and default servers: default:443 svn.mycompany.com (/etc/httpd/conf.d/ssl.conf:74) *:80 is a NameVirtualHost default server svn.mycompany.com (/etc/httpd/conf/httpd.conf:1012) port 80 namevhost svn.mycompany.com (/etc/httpd/conf/httpd.conf:1012) Syntax OK

    Read the article

  • usb_modeswitch not switching

    - by deniz
    After I upgraded from kernel 2.6.18 to 3.5.3 modeswitch started not to work for me. Although lsusb shows my usb modem, usb_modeswitch does not switch it. My system information is like below. I ran lsusb, dmesg, usb-devices and usb_modeswitch their output is like below. usb_modeswitch instead of switching my modem it says "No devices in default mode found. Nothing to do. Bye.". Can you offer a solution? Kernel: Linux 3.5.3 usb_modeswitch: 1.2.3-1 usb_modeswitch-data: 20120120-1 usbutils: 006-1 libusb: 1.0.8-0.1 root@localhost$ lsusb Bus 002 Device 029: ID 12d1:1446 Huawei Technologies Co., Ltd. root@localhost$ dmesg [70112.477080] usb 2-1.4: new high-speed USB device number 30 using ehci_hcd [70112.567757] scsi49 : usb-storage 2-1.4:1.0 [70112.567842] scsi50 : usb-storage 2-1.4:1.1 [70113.571433] scsi 49:0:0:0: CD-ROM HUAWEI Mass Storage 2.31 PQ: 0 ANSI: 2 [70113.572304] scsi 50:0:0:0: Direct-Access HUAWEI TF CARD Storage PQ: 0 ANSI: 2 [70113.574169] sr0: scsi-1 drive [70113.574223] sr 49:0:0:0: Attached scsi CD-ROM sr0 [70113.574250] sr 49:0:0:0: Attached scsi generic sg1 type 5 [70113.574350] sd 50:0:0:0: Attached scsi generic sg2 type 0 [70113.577173] sd 50:0:0:0: [sdb] Attached SCSI removable disk root@localhost$ usb-devices T: Bus=02 Lev=02 Prnt=02 Port=03 Cnt=01 Dev#= 30 Spd=480 MxCh= 0 D: Ver= 2.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1 P: Vendor=12d1 ProdID=1446 Rev=00.00 S: Manufacturer=Huawei Technologies S: Product=HUAWEI Mobile C: #Ifs= 2 Cfg#= 1 Atr=c0 MxPwr=500mA I: If#= 0 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage I: If#= 1 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage root@localhost$ cat /etc/usb_modeswitch.d/12d1\:1446 # Huawei, newer modems TargetVendor= 0x12d1 TargetProductList="1001,1406,140b,140c,1412,141b,1433,1436,14ac,1506" MessageContent="55534243123456780000000000000011062000000100000000000000000000" root@localhost$ usb_modeswitch -c /etc/usb_modeswitch.d/12d1:1446 -v 12d1 -p 1446 -W * usb_modeswitch: handle USB devices with multiple modes * Version 1.2.3 (C) Josua Dietze 2012 * Based on libusb0 (0.1.12 and above) ! PLEASE REPORT NEW CONFIGURATIONS ! DefaultVendor= 0x12d1 DefaultProduct= 0x1446 TargetVendor= 0x12d1 TargetProduct= not set TargetClass= not set TargetProductList="1001,1406,140b,140c,1412,141b,1433,1436,14ac,1506" DetachStorageOnly=0 HuaweiMode=0 SierraMode=0 SonyMode=0 QisdaMode=0 GCTMode=0 KobilMode=0 SequansMode=0 MobileActionMode=0 CiscoMode=0 MessageEndpoint= not set MessageContent="55534243123456780000000000000011062000000100000000000000000000" NeedResponse=0 ResponseEndpoint= not set InquireDevice enabled (default) Success check disabled System integration mode disabled usb_set_debug: Setting debugging level to 15 (on) usb_os_find_busses: Skipping non bus directory devices usb_os_find_busses: Skipping non bus directory drivers usb_os_find_busses: Skipping non bus directory uevent usb_os_find_busses: Skipping non bus directory drivers_probe usb_os_find_busses: Skipping non bus directory drivers_autoprobe Looking for target devices ... No devices in target mode or class found Looking for default devices ... No devices in default mode found. Nothing to do. Bye. Thanks in advance.

    Read the article

  • Is my Cisco switch port bad?

    - by ewwhite
    I've been chasing a packet-loss and network stability issue for a handful of end-users on an internal network for the past few days... These issues surfaced last week, however the location was struck by lightning six weeks ago. I was seeing 5-10% packet loss between a stack of four Cisco 2960's and several PC's and phones on the other side of a 77-meter run. The PC's were run inline with the phones over a trunked link (switchport configuration pastebin). We were seeing dropped calls and interruptions in client-server applications and Microsoft Exchange connectivity. I tried the usual troubleshooting steps remotely, having a local technician do the following during breaks in user and production activity: change cables between the wall jack and device. change patch cables between the patch panel and switch port(s). try different switch ports within the 2960 stack. change end-user devices with known-good equipment (new phones, different PC's). clear switch port interface counters and monitor incrementing errors closely. (Pastebin output of sh int) Pored over the device logs and Observium RRD graphs. No link up/down issues from the switch side. change power strips on the end-user side. test cable runs from the Cisco 2960 using test cable-diagnostics tdr int Gi4/0/9 (clean)* test cable runs with a Tripp-Lite cable tester. (clean) run diagnostics on the switch stack members. (clean) In the end, it took three changes of switch ports to find a stable solution. The only logical conclusion is that a few Cisco 2960 switch ports are bad or flaky... Not dead, but not consistent in behavior either. I'm not used to seeing individual ports die in this manner. What else can I test or check to determine if these devices are bad? Is it common for single ports to have problems, rather than a contiguous bank of ports? BTW - show cable-diagnostics tdr int Gi4/0/14 is very cool... Interface Speed Local pair Pair length Remote pair Pair status --------- ----- ---------- ------------------ ----------- -------------------- Gi4/0/14 1000M Pair A 79 +/- 0 meters Pair B Normal Pair B 75 +/- 0 meters Pair A Normal Pair C 77 +/- 0 meters Pair D Normal Pair D 79 +/- 0 meters Pair C Normal

    Read the article

  • Why apcupsd won't see the UPS connected to the USB posrt on FreeBSD 8.0 amd64

    - by Max Kosyakov
    Hello, Recently I installed an apcusbd on a FreeBSD 8.0 amd64 box via ports system. It installed perfectly but it won't run. Here what is says in the log: FATAL ERROR in generic-usb.c at line 636 Cannot find UPS device It appeared that HID driver picked the /dev/ugen4.2 which could cause the apcusb being unable to find the device. After I had discovered this, I rebuilt the kernel and removed the hid driver. Now it just shows "ugen4.2: <Tripp Lite> at usbus4" and no uhid0 device appears. Nevertheless the problem persisted. I tried to leave the DEVICE config setting blank --- won't help. Then I specified the particular device in the config, but it did not help either. Below you is the output of several commands that can provide some useful information on my case. server# /usr/local/etc/rc.d/apcupsd start Starting apcupsd. server# tail /var/log/messages | grep apcupsd Jun 17 22:30:00 server apcupsd[1520]: apcupsd FATAL ERROR in generic-usb.c at line 636 Cannot find UPS device -- For a link to detailed USB trouble shooting information, please see . Jun 17 22:30:00 server apcupsd[1520]: apcupsd error shutdown completed server# cat /usr/local/etc/apcupsd/apcupsd.conf ## apcupsd.conf v1.1 ## UPSCABLE usb UPSTYPE usb DEVICE /dev/ugen4.2 LOCKFILE /var/lock UPSCLASS standalone UPSMODE disable server# dmesg | grep '^u' uhci0: port 0xa800-0xa81f irq 16 at device 26.0 on pci0 uhci0: [ITHREAD] uhci0: LegSup = 0x0f00 usbus0: on uhci0 uhci1: port 0xa880-0xa89f irq 21 at device 26.1 on pci0 uhci1: [ITHREAD] uhci1: LegSup = 0x0f00 usbus1: on uhci1 uhci2: port 0xac00-0xac1f irq 18 at device 26.2 on pci0 uhci2: [ITHREAD] uhci2: LegSup = 0x0f00 usbus2: on uhci2 usbus3: EHCI version 1.0 usbus3: on ehci0 uhci3: port 0xa080-0xa09f irq 23 at device 29.0 on pci0 uhci3: [ITHREAD] uhci3: LegSup = 0x0f00 usbus4: on uhci3 uhci4: port 0xa400-0xa41f irq 19 at device 29.1 on pci0 uhci4: [ITHREAD] uhci4: LegSup = 0x0f00 usbus5: on uhci4 uhci5: port 0xa480-0xa49f irq 18 at device 29.2 on pci0 uhci5: [ITHREAD] uhci5: LegSup = 0x0f00 usbus6: on uhci5 usbus7: EHCI version 1.0 usbus7: on ehci1 uart0: port 0x3f8-0x3ff irq 4 flags 0x10 on acpi0 uart0: [FILTER] usbus0: 12Mbps Full Speed USB v1.0 usbus1: 12Mbps Full Speed USB v1.0 usbus2: 12Mbps Full Speed USB v1.0 usbus3: 480Mbps High Speed USB v2.0 usbus4: 12Mbps Full Speed USB v1.0 usbus5: 12Mbps Full Speed USB v1.0 usbus6: 12Mbps Full Speed USB v1.0 usbus7: 480Mbps High Speed USB v2.0 ugen0.1: at usbus0 uhub0: on usbus0 ugen1.1: at usbus1 uhub1: on usbus1 ugen2.1: at usbus2 uhub2: on usbus2 ugen3.1: at usbus3 uhub3: on usbus3 ugen4.1: at usbus4 uhub4: on usbus4 ugen5.1: at usbus5 uhub5: on usbus5 ugen6.1: at usbus6 uhub6: on usbus6 ugen7.1: at usbus7 uhub7: on usbus7 uhub0: 2 ports with 2 removable, self powered uhub1: 2 ports with 2 removable, self powered uhub2: 2 ports with 2 removable, self powered uhub4: 2 ports with 2 removable, self powered uhub5: 2 ports with 2 removable, self powered uhub6: 2 ports with 2 removable, self powered uhub3: 6 ports with 6 removable, self powered uhub7: 6 ports with 6 removable, self powered ugen4.2: at usbus4 server#

    Read the article

  • How to know the source of certain TCP traffic on AIX

    - by A.Rashad
    We have two AIX boxes, one for production system and another for testing. both systems are running ATM machine switches, where the ATM device is connected via TCP socket. we had an issue on production system where the machine would power off or get disconnected but the netstat -na | grep <IP of machine > would still mention that the socket is up when simulated that case on the UAT environment, the problem did not happen, where the socket would terminate in 3 to 5 minutes. when sniffed on the traffic between the machine and ATM we found that no traffic takes place on production while there is some sort of heartbeat on UAT. but it is not initiated by the application. $>tcpdump | grep -v "10.2.2.71" | grep -v "HSRP" | grep "10.3.1.30" tcpdump: verbose output suppressed, use -v or -vv for full protocol decode listening on en6, link-type 1, capture size 96 bytes 09:08:13.323421 IP server073.afs3-callback > 10.3.1.30.impera: . 278204201:278204202(1) ack 3307884029 win 164 09:08:13.335334 IP 10.3.1.30.impera > server073.afs3-callback: . ack 1 win 64180 09:08:23.425771 IP 10.3.1.30.impera > server073.afs3-callback: . 1:2(1) ack 1 win 64180 09:08:23.425789 IP server073.afs3-callback > 10.3.1.30.impera: . ack 2 win 65535 09:09:13.628985 IP server073.afs3-callback > 10.3.1.30.impera: . 0:1(1) ack 1 win 164 09:09:13.633900 IP 10.3.1.30.impera > server073.afs3-callback: . ack 1 win 64180 09:09:23.373634 IP 10.3.1.30.impera > server073.afs3-callback: . 1:2(1) ack 1 win 64180 09:09:23.373647 IP server073.afs3-callback > 10.3.1.30.impera: . ack 2 win 65535 while on production, that traffic is not there. we want to know where this traffic is initiated from to implement on production to sense disconnection our comms parameters are: tcp_keepcnt = 2 tcp_keepidle = 100 tcp_keepinit = 150 tcp_keepintvl = 150 tcp_finwait2 = 1200 can anyone help?

    Read the article

  • 64-bit linux kernel only seeing 3 of 4GB after upgrade...

    - by Blaine
    Hey everyone. I am running Ubuntu 9.04 64-bit on my macbook. I had 2GB of ram before, and everything ran great. I just upgraded to 2x2GB (4GB), but my system only sees 3GB of it. OS X, which I am dual booting, sees all 4GB. Also, my video performance is incredibly lacking. Before the upgrade my compiz benchmark was full at 80fps, and now it is at 22fps with very choppy window dragging. Has anyone ever heard of this on a 64-bit kernel? I just don't quite understand what could be the issue. 10$ uname -a Linux macbook 2.6.28-15-generic #49-Ubuntu SMP Tue Aug 18 19:25:34 UTC 2009 x86_64 GNU/Linux $ free -m total used free shared buffers cached Mem: 2953 1031 1921 0 114 427 -/+ buffers/cache: 489 2463 Swap: 7812 0 7812 9$ lsmod Module Size Used by i915 77960 2 drm 123232 3 i915 binfmt_misc 18572 1 ppdev 16904 0 btusb 21784 2 bridge 63776 0 stp 11140 1 bridge bnep 22912 2 vboxnetadp 109356 0 vboxnetflt 116972 0 vboxdrv 1721612 1 vboxnetflt uvcvideo 69640 0 compat_ioctl32 18304 1 uvcvideo videodev 45184 2 uvcvideo,compat_ioctl32 v4l1_compat 23940 2 uvcvideo,videodev lp 19588 0 parport 49584 2 ppdev,lp snd_hda_intel 557492 3 snd_pcm_oss 52352 0 snd_mixer_oss 24960 1 snd_pcm_oss snd_pcm 99464 2 snd_hda_intel,snd_pcm_oss arc4 10240 2 snd_seq_dummy 11524 0 ecb 11392 2 snd_seq_oss 41984 0 snd_seq_midi 15744 0 snd_rawmidi 33920 1 snd_seq_midi snd_seq_midi_event 16512 2 snd_seq_oss,snd_seq_midi snd_seq 66272 6 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_seq_midi_event ath9k 310584 0 snd_timer 34064 2 snd_pcm,snd_seq snd_seq_device 16276 5 snd_seq_dummy,snd_seq_oss,snd_seq_midi,snd_rawmidi,snd_seq mac80211 251528 1 ath9k iTCO_wdt 21712 0 iTCO_vendor_support 12420 1 iTCO_wdt joydev 20992 0 video 29204 0 snd 78920 15 snd_hda_intel,snd_pcm_oss,snd_mixer_oss,snd_pcm,snd_seq_oss,snd_rawmidi,snd_seq,snd_timer,snd_seq_device applesmc 37700 0 output 11648 1 video soundcore 16800 1 snd pcspkr 11136 0 cfg80211 43680 1 mac80211 appletouch 19972 0 isight_firmware 11520 0 input_polldev 12688 1 applesmc intel_agp 39408 1 snd_page_alloc 18704 2 snd_hda_intel,snd_pcm led_class 13064 2 ath9k,applesmc hid_apple 15872 0 usbhid 47040 0 ohci1394 42164 0 ieee1394 108288 1 ohci1394 sky2 63364 0 fbcon 49792 0 tileblit 11264 1 fbcon font 17024 1 fbcon bitblit 14464 1 fbcon softcursor 10368 1 bitblit Some information from dmesg: [ 795.820163] ACPI: EC: GPE storm detected, transactions will use polling mode [ 1762.709516] [drm:i915_getparam] *ERROR* Unknown parameter 6 [ 1763.078130] [drm:i915_getparam] *ERROR* Unknown parameter 6 [ 2362.760889] [drm:i915_getparam] *ERROR* Unknown parameter 6 [ 2416.352084] ACPI: EC: missing confirmations, switch off interrupt mode. [ 3718.721095] [drm:i915_getparam] *ERROR* Unknown parameter 6 [ 3719.108914] [drm:i915_getparam] *ERROR* Unknown parameter 6 [ 4318.773266] [drm:i915_getparam] *ERROR* Unknown parameter 6 [ 9513.813066] CE: hpet increasing min_delta_ns to 15000 nsec [ 9693.815684] npviewer.bin[6736]

    Read the article

  • Secure openVPN using IPTABLES

    - by bob franklin smith harriet
    Hey, I setup an openVPN server and it works ok. The next step is to secure it, I opted to use IPTABLES to only allow certain connections through but so far it is not working. I want to enable access to the network behind my openVPN server, and allow other services (web access), when iptables is disabaled or set to allow all this works fine, when using my following rules it does not. also note, I already configured openVPN itself to do what i want and it works fine, its only failing when iptables is started. Any help to tell me why this isnt working will appreciated here. These are the lines that I added in accordance with openVPN's recommendations, unfortunately testing these commands shows that they are requiered, they seem incredibly insecure though, any way to get around using them? # Allow TUN interface connections to OpenVPN server -A INPUT -i tun+ -j ACCEPT #allow TUN interface connections to be forwarded through other interfaces -A FORWARD -i tun+ -j ACCEPT # Allow TAP interface connections to OpenVPN server -A INPUT -i tap+ -j ACCEPT # Allow TAP interface connections to be forwarded through other interfaces -A FORWARD -i tap+ -j ACCEPT These are the new chains and commands i added to restrict access as much as possible unfortunately with these enabled, all that happens is the openVPN connection establishes fine, and then there is no access to the rest of the network behind the openVPN server note I am configuring the main iptables file and I am paranoid so all ports and ip addresses are altered, and -N etc appears before this so ignore that they dont appear. and i added some explanations of what i 'intended' these rules to do, so you dont waste time figuring out where i went wrong : 4 #accepts the vpn over port 1192 -A INPUT -p udp -m udp --dport 1192 -j ACCEPT -A INPUT -j INPUT-FIREWALL -A OUTPUT -j ACCEPT #packets that are to be forwarded from 10.10.1.0 network (all open vpn clients) to the internal network (192.168.5.0) jump to [sic]foward-firewall chain -A FORWARD -s 10.10.1.0/24 -d 192.168.5.0/24 -j FOWARD-FIREWALL #same as above, except for a different internal network -A FORWARD -s 10.10.1.0/24 -d 10.100.5.0/24 -j FOWARD-FIREWALL # reject any not from either of those two ranges -A FORWARD -j REJECT -A INPUT-FIREWALL -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT-FIREWALL -p tcp -m tcp --dport 22 -j ACCEPT -A INPUT-FIREWALL -j REJECT -A FOWARD-FIREWALL -m state --state RELATED,ESTABLISHED -j ACCEPT #80 443 and 53 are accepted -A FOWARD-FIREWALL -m tcp -p tcp --dport 80 -j ACCEPT -A FOWARD-FIREWALL -m tcp -p tcp --dport 443 -j ACCEPT #192.168.5.150 = openVPN sever -A FOWARD-FIREWALL -m tcp -p tcp -d 192.168.5.150 --dport 53 -j ACCEPT -A FOWARD-FIREWALL -m udp -p udp -d 192.168.5.150 --dport 53 -j ACCEPT -A FOWARD-FIREWALL -j REJECT COMMIT now I wait :D

    Read the article

  • Encoding multiple video streams with a single avconv invocation

    - by automatthias
    I played with avconv on Ubuntu and I'm now able to e.g. record the desktop with sound from a soundcard. One thing I wanted to do was recording two video inputs at the same time, for instance the desktop and from the webcam. I thought about doing something like this: avconv \ -f alsa \ -i default \ -acodec flac \ -f video4linux2 \ -r 6 \ -i /dev/video0 \ -f x11grab \ -i :0.0 \ out.mkv My thinking was that if you define multiple video inputs, and the .mkv format can handle multiple video streams, avconv will encode 2 video streams and 1 audio stream into one file. But this isn't what happens: avconv version 0.8.4-6:0.8.4-0ubuntu0.12.10.1, Copyright (c) 2000-2012 the Libav developers built on Nov 6 2012 16:51:11 with gcc 4.7.2 [alsa @ 0x1091bc0] capture with some ALSA plugins, especially dsnoop, may hang. [alsa @ 0x1091bc0] Estimating duration from bitrate, this may be inaccurate Input #0, alsa, from 'default': Duration: N/A, start: 1354364317.020350, bitrate: N/A Stream #0.0: Audio: pcm_s16le, 48000 Hz, 2 channels, s16, 1536 kb/s [video4linux2 @ 0x10923e0] Estimating duration from bitrate, this may be inaccurate Input #1, video4linux2, from '/dev/video0': Duration: N/A, start: 100607.724745, bitrate: 29491 kb/s Stream #1.0: Video: rawvideo, yuyv422, 640x480, 29491 kb/s, 6 tbr, 1000k tbn, 6 tbc [x11grab @ 0x107b2a0] device: :0.0+83,87 -> display: :0.0 x: 83 y: 87 width: 854 height: 480 [x11grab @ 0x107b2a0] shared memory extension found [x11grab @ 0x107b2a0] Estimating duration from bitrate, this may be inaccurate Input #2, x11grab, from ':0.0+83,87': Duration: N/A, start: 1354364318.488382, bitrate: 196761 kb/s Stream #2.0: Video: rawvideo, bgra, 854x480, 196761 kb/s, 15 tbr, 1000k tbn, 15 tbc Incompatible pixel format 'bgra' for codec 'mpeg4', auto-selecting format 'yuv420p' [buffer @ 0x107fcc0] w:854 h:480 pixfmt:bgra [avsink @ 0x10bdf00] auto-inserting filter 'auto-inserted scaler 0' between the filter 'src' and the filter 'out' [scale @ 0x10dc680] w:854 h:480 fmt:bgra -> w:854 h:480 fmt:yuv420p flags:0x4 Output #0, matroska, to '.../out.mkv': Metadata: encoder : Lavf53.21.0 Stream #0.0: Video: mpeg4, yuv420p, 854x480, q=2-31, 4000 kb/s, 1k tbn, 15 tbc Stream #0.1: Audio: libvorbis, 48000 Hz, 2 channels, s16 Stream mapping: Stream #2:0 -> #0:0 (rawvideo -> mpeg4) Stream #0:0 -> #0:1 (pcm_s16le -> libvorbis) Press ctrl-c to stop encoding [mpeg4 @ 0x10bd800] rc buffer underflow ^Cframe= 160 fps= 15 q=2.0 Lsize= 3414kB time=10.66 bitrate=2623.0kbits/s video:3273kB audio:131kB global headers:4kB muxing overhead 0.165600% Received signal 2: terminating. I'm not sure if it's the question of mapping (some -map options to add?) or that avconv just can't encode more than 1 video stream at one time. So is it an actual avconv limitation, or a limitation of the available containers, or me simply not finding the right combination of command line options?

    Read the article

  • Different files on shared partition?

    - by Matt Robertson
    I am dual-booting Windows 8 and Ubuntu 12.04. My partition scheme looks like this: /dev/sda1 - Windows 8 (nfts) /dev/sda2 - Ubuntu / (ext4) /dev/sda3 - Ubuntu home (ext4) /dev/sda5 - swap /dev/sda6 - Shared data partition (exfat) (First off, yes I do have exfat libraries installed on Ubuntu) I created some PNG images in Windows and saved them on my shared partition. From Ubuntu, I edited the images in GIMP and saved them (replacing the ones on the shared partition). When I boot into Windows, the files appear unchanged - exactly like they did before I edited them from Ubuntu. I even added a folder and deleted some other files, but none of these changes exist in Windows. When I boot into Ubuntu, all of the changes are still there. It is as if Windows is caching the old file structure... How is this possible? Thanks in advance. Edit -- commands output ~~ lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT sda 8:0 0 465.8G 0 disk +-sda1 8:1 0 165.1G 0 part +-sda2 8:2 0 21.3G 0 part / +-sda3 8:3 0 98.9G 0 part /home +-sda4 8:4 0 1K 0 part +-sda5 8:5 0 7.8G 0 part [SWAP] +-sda6 8:6 0 172.7G 0 part /mnt/shared_data ~~ /etc/fstab # <file system> <mount point> <type> <options> <dump> <pass> proc /proc proc nodev,noexec,nosuid 0 0 # /dev/sda2 UUID=8f700f65-b5c7-4afc-a6fb-8f9271e0fb5e / ext4 errors=remount-ro 0 1 # /dev/sda3 UUID=f0d688b7-22bd-4fa7-bc1b-a594af2933fa /home ext4 defaults 0 2 # /dev/sda5 UUID=3bc2399b-5deb-4f04-924b-d4fc77491997 none swap sw 0 0 # /dev/sda6 UUID=F2DE-BC47 /mnt/shared_data exfat defaults 0 3 ~~ /etc/mtab /dev/sda2 / ext4 rw,errors=remount-ro 0 0 proc /proc proc rw,noexec,nosuid,nodev 0 0 sysfs /sys sysfs rw,noexec,nosuid,nodev 0 0 none /sys/fs/fuse/connections fusectl rw 0 0 none /sys/kernel/debug debugfs rw 0 0 none /sys/kernel/security securityfs rw 0 0 udev /dev devtmpfs rw,mode=0755 0 0 devpts /dev/pts devpts rw,noexec,nosuid,gid=5,mode=0620 0 0 tmpfs /run tmpfs rw,noexec,nosuid,size=10%,mode=0755 0 0 none /run/lock tmpfs rw,noexec,nosuid,nodev,size=5242880 0 0 none /run/shm tmpfs rw,nosuid,nodev 0 0 /dev/sda3 /home ext4 rw 0 0 /dev/sda6 /mnt/shared_data fuseblk rw,nosuid,nodev,allow_other,blksize=4096 0 0 binfmt_misc /proc/sys/fs/binfmt_misc binfmt_misc rw,noexec,nosuid,nodev 0 0 gvfs-fuse-daemon /home/matt/.gvfs fuse.gvfs-fuse-daemon rw,nosuid,nodev,user=matt 0 0

    Read the article

  • .htaccess template, suggestions needed

    - by purpler
    DefaultLanguage en-US FileETag None Header unset ETag ServerSignature Off SetEnv TZ Europe/Belgrade # Rewrites Options +FollowSymLinks RewriteEngine On RewriteBase / # Redirect to WWW RewriteCond %{HTTP_HOST} ^serpentineseo.com RewriteRule (.*) http://www.serpentineseo.com/$1 [R=301,L] # Redirect index to root RewriteCond %{THE_REQUEST} ^[A-Z]{3,9}\ /.*index\.html\ HTTP/ RewriteRule ^(.*)index\.html$ /$1 [R=301,L] # Cache media files: ExpiresActive On ExpiresDefault A0 # Month <filesMatch "\.(gif|jpg|jpeg|png|ico|swf|js)$"> Header set Cache-Control "max-age=2592000, public" </filesMatch> # Week <FilesMatch "\.(css|pdf)$"> Header set Cache-Control "max-age=604800" </FilesMatch> # 10 Min <FilesMatch "\.(html|htm|txt)$"> Header set Cache-Control "max-age=600" </FilesMatch> # Do not cache <FilesMatch "\.(pl|php|cgi|spl|scgi|fcgi)$"> Header unset Cache-Control </FilesMatch> # Compress output <IfModule mod_deflate.c> <FilesMatch "\.(html|js|css)$"> SetOutputFilter DEFLATE </FilesMatch> </IfModule> # Error Documents ErrorDocument 206 /error/206.html ErrorDocument 401 /error/401.html ErrorDocument 403 /error/403.html ErrorDocument 404 /error/404.html ErrorDocument 500 /error/500.html # Prevent hotlinking RewriteCond %{HTTP_REFERER} !^$ RewriteCond %{HTTP_REFERER} !^http://(www\.)?serpentineseo.com/.*$ [NC] RewriteRule \.(gif|jpg|png)$ http://www.serpentineseo.com/images/angryman.png [R,L] # Prevent offline browsers RewriteCond %{HTTP_USER_AGENT} ^BlackWidow [OR] RewriteCond %{HTTP_USER_AGENT} ^Bot\ mailto:[email protected] [OR] RewriteCond %{HTTP_USER_AGENT} ^ChinaClaw [OR] RewriteCond %{HTTP_USER_AGENT} ^Custo [OR] RewriteCond %{HTTP_USER_AGENT} ^DISCo [OR] RewriteCond %{HTTP_USER_AGENT} ^Download\ Demon [OR] RewriteCond %{HTTP_USER_AGENT} ^eCatch [OR] RewriteCond %{HTTP_USER_AGENT} ^EirGrabber [OR] RewriteCond %{HTTP_USER_AGENT} ^EmailSiphon [OR] RewriteCond %{HTTP_USER_AGENT} ^EmailWolf [OR] RewriteCond %{HTTP_USER_AGENT} ^Express\ WebPictures [OR] RewriteCond %{HTTP_USER_AGENT} ^ExtractorPro [OR] RewriteCond %{HTTP_USER_AGENT} ^EyeNetIE [OR] RewriteCond %{HTTP_USER_AGENT} ^FlashGet [OR] RewriteCond %{HTTP_USER_AGENT} ^GetRight [OR] RewriteCond %{HTTP_USER_AGENT} ^GetWeb! [OR] RewriteCond %{HTTP_USER_AGENT} ^Go!Zilla [OR] RewriteCond %{HTTP_USER_AGENT} ^Go-Ahead-Got-It [OR] RewriteCond %{HTTP_USER_AGENT} ^GrabNet [OR] RewriteCond %{HTTP_USER_AGENT} ^Grafula [OR] RewriteCond %{HTTP_USER_AGENT} ^HMView [OR] RewriteCond %{HTTP_USER_AGENT} HTTrack [NC,OR] RewriteCond %{HTTP_USER_AGENT} ^Image\ Stripper [OR] RewriteCond %{HTTP_USER_AGENT} ^Image\ Sucker [OR] RewriteCond %{HTTP_USER_AGENT} Indy\ Library [NC,OR] RewriteCond %{HTTP_USER_AGENT} ^InterGET [OR] RewriteCond %{HTTP_USER_AGENT} ^Internet\ Ninja [OR] RewriteCond %{HTTP_USER_AGENT} ^JetCar [OR] RewriteCond %{HTTP_USER_AGENT} ^JOC\ Web\ Spider [OR] RewriteCond %{HTTP_USER_AGENT} ^larbin [OR] RewriteCond %{HTTP_USER_AGENT} ^LeechFTP [OR] RewriteCond %{HTTP_USER_AGENT} ^Mass\ Downloader [OR] RewriteCond %{HTTP_USER_AGENT} ^MIDown\ tool [OR] RewriteCond %{HTTP_USER_AGENT} ^Mister\ PiX [OR] RewriteCond %{HTTP_USER_AGENT} ^Navroad [OR] RewriteCond %{HTTP_USER_AGENT} ^NearSite [OR] RewriteCond %{HTTP_USER_AGENT} ^NetAnts [OR] RewriteCond %{HTTP_USER_AGENT} ^NetSpider [OR] RewriteCond %{HTTP_USER_AGENT} ^Net\ Vampire [OR] RewriteCond %{HTTP_USER_AGENT} ^NetZIP [OR] RewriteCond %{HTTP_USER_AGENT} ^Octopus [OR] RewriteCond %{HTTP_USER_AGENT} ^Offline\ Explorer [OR] RewriteCond %{HTTP_USER_AGENT} ^Offline\ Navigator [OR] RewriteCond %{HTTP_USER_AGENT} ^PageGrabber [OR] RewriteCond %{HTTP_USER_AGENT} ^Papa\ Foto [OR] RewriteCond %{HTTP_USER_AGENT} ^pavuk [OR] RewriteCond %{HTTP_USER_AGENT} ^pcBrowser [OR] RewriteCond %{HTTP_USER_AGENT} ^RealDownload [OR] RewriteCond %{HTTP_USER_AGENT} ^ReGet [OR] RewriteCond %{HTTP_USER_AGENT} ^SiteSnagger [OR] RewriteCond %{HTTP_USER_AGENT} ^SmartDownload [OR] RewriteCond %{HTTP_USER_AGENT} ^SuperBot [OR] RewriteCond %{HTTP_USER_AGENT} ^SuperHTTP [OR] RewriteCond %{HTTP_USER_AGENT} ^Surfbot [OR] RewriteCond %{HTTP_USER_AGENT} ^tAkeOut [OR] RewriteCond %{HTTP_USER_AGENT} ^Teleport\ Pro [OR] RewriteCond %{HTTP_USER_AGENT} ^VoidEYE [OR] RewriteCond %{HTTP_USER_AGENT} ^Web\ Image\ Collector [OR] RewriteCond %{HTTP_USER_AGENT} ^Web\ Sucker [OR] RewriteCond %{HTTP_USER_AGENT} ^WebAuto [OR] RewriteCond %{HTTP_USER_AGENT} ^WebCopier [OR] RewriteCond %{HTTP_USER_AGENT} ^WebFetch [OR] RewriteCond %{HTTP_USER_AGENT} ^WebGo\ IS [OR] RewriteCond %{HTTP_USER_AGENT} ^WebLeacher [OR] RewriteCond %{HTTP_USER_AGENT} ^WebReaper [OR] RewriteCond %{HTTP_USER_AGENT} ^WebSauger [OR] RewriteCond %{HTTP_USER_AGENT} ^Website\ eXtractor [OR] RewriteCond %{HTTP_USER_AGENT} ^Website\ Quester [OR] RewriteCond %{HTTP_USER_AGENT} ^WebStripper [OR] RewriteCond %{HTTP_USER_AGENT} ^WebWhacker [OR] RewriteCond %{HTTP_USER_AGENT} ^WebZIP [OR] RewriteCond %{HTTP_USER_AGENT} ^Wget [OR] RewriteCond %{HTTP_USER_AGENT} ^Widow [OR] RewriteCond %{HTTP_USER_AGENT} ^WWWOFFLE [OR] RewriteCond %{HTTP_USER_AGENT} ^Xaldon\ WebSpider [OR] RewriteCond %{HTTP_USER_AGENT} ^Zeus RewriteRule ^.*$ http://www.google.com [R,L] # Protect against DOS attacks by limiting file upload size LimitRequestBody 10240000 # Deny access to sensitive files <FilesMatch "\.(htaccess|psd|log)$"> Order Allow,Deny Deny from all </FilesMatch>

    Read the article

  • Hang while starting several daemons [solved]

    - by Adrian Lang
    I’m running a Debian Squeeze AMD64 server. Target runlevel after boot is runlevel 2, which includes rsyslogd, cron, sshd and some other stuff, but not dovecot, postfix, apache2, etc. The system fails to reach runlevel 2 with several symptoms: The system hangs at trying to start rsyslogd Booting into runlevel 1 works, then login from the console works Starting rsyslogd from runlevel 1 via /etc/init.d/rsyslog hangs Starting runlevel 2 with rsyslogd disabled works But then, logging in via console fails: I get the motd, and then nothing Starting sshd from runlevel 1 succeeds But then, I cannot login via ssh. Sometimes password ssh login gives me the motd and then nothing, sometimes not even this. Trying to offer a public key seems to annoy the sshd enough to not talk to me any further. When rebooting from runlevel 1, the server hangs at trying to stop apache2 (which is not running, so this really should be trivial). Trying to stop apache2 when logged in in runleve 1 does hang as well. And that’s just the stuff which fails all the time. RAM has been tested, dmesg shows no problems. I have no clue. Update: (shortened) output from rsyslogd -c4 -d called in runlevel 1 rsyslogd 4.6.4 startup, compatibility mode 4, module path '' caller requested object 'net', not found (iRet -3003) Requested to load module 'lmnet' loading module '/user/lib/rsyslog/lmnet.so' module of type 2 being loaded conf.c requested ref for 'lmnet', refcount 1 rsylog runtime initialized, version 4.6.4, current users 1 syslogd.c requested ref for 'lmnet', refcount now 2 I can kill rsyslogd with Strg+C, then. /var/log shows none of the configured log files, though. Update2: Thanks to @DerfK I still have no clue, but at least I narrowed down the problem. I’m now testing with /etc/init.d/apache2 stop (without an apache2 running, of course) which hangs as well and looks like an even more obvious failure. After some testing I found out that a file with one single line: /usr/sbin/apache2ctl configtest /dev/null 2&1 hangs, while the same line executed in an interactive shell works. I was not able to further reduce this line while, i. e. every single part, the stream redirections and the commando itself is necessary to reproduce the hang. @DerfK also pointed me to strace which gave a shallow hint about what kind of hang we have here: wait4(-1for the init scripts futex(0xsomepointer, FUTEX_WAIT_PRIVATE, 2, NULL for rsyslogd / apache2 binaries called by the init scripts The system was installed as a Debian Lenny by my hoster in autumn 2011, I upgraded it to Squeeze immediately and kept it up to date with Squeeze, which then used to be testing. There were no big changes, though. I guess I never tried to reboot the system before. Update3: I found the problem. My /etc/nsswitch.conf specified ldap as hosts lookup backup, which is not available at that time of the boot. Relying on dns solely fixes my boot problems.

    Read the article

  • Can't get my Raspberry Pi to keep a static IP

    - by JonnyIrving
    I recently got given a Raspberry Pi and I would like to be able to remote into it using puTTy from my laptop so I don't have to sit next to my tv with a keyboard and mouse to use it. I am able to get a puTTy session going when I know the IP address that my router has given the Pi on each session but it keeps changing on each reboot as I would expect. So I followed a number if instruction to go about configuring the RPi to keep a static IP address. This involved changing the file at '/etc/netwrok/interfaces' which now contains (password removed): auto lo iface lo inet loopback iface eth0 inet static address 192.168.1.82 netmask 255.255.255.0 gateway 192.168.1.254 auto wlan0 allow-hotplug wlan0 iface wlan0 inet dhcp wpa-ssid "BeBoxD304BF" wpa-psk "**********" Despite this however, each time I reboot my RPi it gives me a new dynamic IP address still. I also noticed that in the 'ifconfig' output below that the details of the eth0 doesn't contain IP details for inet addr, Bcast or Mask which have been present in all other examples I have seen online. eth0 Link encap:Ethernet HWaddr b8:27:eb:b5:95:da UP BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) wlan0 Link encap:Ethernet HWaddr 00:87:c6:00:33:77 inet addr:192.168.1.83 Bcast:192.168.1.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:918 errors:0 dropped:0 overruns:0 frame:0 TX packets:277 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 Also I'm not sure if this is relevant but it can't hurt! The file at '/etc/resolv.conf' contains: domain config search config nameserver 192.168.1.254 ..I heard it might mean something on one of the pages I was looking at. I would be very grateful for any help with this. I have tried everything I can think of and would really like to get this working this weekend so I can use it from work.

    Read the article

  • Spaces and Parenthesis in windows PATH variable screws up batch files.

    - by NoName
    So, my path variable (System-Adv Settings-Env Vars-System-PATH) is set to: C:\Python26\Lib\site-packages\PyQt4\bin; %SystemRoot%\system32; %SystemRoot%; %SystemRoot%\System32\Wbem; %SYSTEMROOT%\System32\WindowsPowerShell\v1.0\; C:\Python26\; C:\Python26\Scripts\; C:\cygwin\bin; "C:\PathWithSpaces\What_is_this_bullshit"; "C:\PathWithSpaces 1.5\What_is_this_bullshit_1.5"; "C:\PathWithSpaces (2.0)\What_is_this_bullshit_2.0"; "C:\Program Files (x86)\IronPython 2.6"; "C:\Program Files (x86)\Subversion\bin"; "C:\Program Files (x86)\Git\cmd"; "C:\Program Files (x86)\PuTTY"; "C:\Program Files (x86)\Mercurial"; Z:\droid\android-sdk-windows\tools; Although, obviously, without the newlines. Notice the lines containing PathWithSpaces - the first has no spaces, the second has a space, and the third has a space followed by a parenthesis. Now, notice the output of this batch file: C:\Program Files (x86)\Microsoft Visual Studio 9.0\VC\bin\>vcvars32.bat C:\Program Files (x86)\Microsoft Visual Studio 9.0\VC\bin>"C:\Program Files (x86 )\Microsoft Visual Studio 9.0\Common7\Tools\vsvars32.bat" Setting environment for using Microsoft Visual Studio 2008 x86 tools. \What_is_this_bullshit_2.0";"C:\Program was unexpected at this time. C:\Program Files (x86)\Microsoft Visual Studio 9.0\VC\bin> set "PATH=C:\Pro gram Files\Microsoft SDKs\Windows\v6.0A\bin;C:\Python26\Lib\site-packages\PyQt4\ bin;C:\Windows\system32;C:\Windows;C:\Windows\System32\Wbem;C:\Windows\System32\ WindowsPowerShell\v1.0\;C:\Python26\;C:\Python26\Scripts\;C:\cygwin\bin;"C:\Path WithSpaces\What_is_this_bullshit";"C:\PathWithSpaces 1.5\What_is_this_bullshit_1 .5";"C:\PathWithSpaces (2.0)\What_is_this_bullshit_2.0";"C:\Program Files (x86)\ IronPython 2.6";"C:\Program Files (x86)\Subversion\bin";"C:\Program Files (x86)\ Git\cmd";"C:\Program Files (x86)\PuTTY";"C:\Program Files (x86)\Mercurial";Z:\dr oid\android-sdk-windows\tools;" or specifically the line: \What_is_this_bullshit_2.0";"C:\Program was unexpected at this time. So, what is this bullshit? Specifically: Directory in path that is properly escaped with quotes, but with no spaces = fine Directory in path that is properly escaped with quotes, and has spaces but no parenthesis = fine Directory in path that is properly escaped with quotes, and has spaces and has a parenthesis = ERROR Whats going on here? How can I fix this? I'll probably resort to a junction point to let my tools still work as workaround, but if you have any insight into this, please let me know :)

    Read the article

  • Internet Working, Browsing Not.

    - by jeffreypriebe
    I have a very odd problem that I can't resolve. I am connected to the internet, but my browsing doesn't work. I don't mean a web browser - I mean browsing. Firefox, Chrome, Curl all fail to successfully connect to an HTTP address. However existing connections, e.g. to mail in Outlook (Exchange Server and also IMAP server) continue to work. Also, the internet is on, I can confirm both from my machine (other ports / connections) as well as from any other computer connected to the same network. Additionally, it appears to be HTTP, not simple a port issue as HTTP over port 8443 (Tortoise SVN if you must know - running over HTTP not over SVN) also fails. I am using Windows Vista SP2 (build 6002). It seems to "creep up" in that after running the computer for a few hours it will fail. (No found way to systematically reproduce the problem.) Additionally, it seems to be more prone on days where the internet connection is flaky already (not sure why the internet is flaky, just is, lot's of failed browsing requests and have to retry/reload often). What I have tried (when the problem arises) - none have yielded any resolution: Resetting the network connection (dis-connect, re-connect) Disable/re-enable the network adapter Double-checked the ip settings Double-checked the HOSTS file. Note: DNS continues to work (both new and cached responses to DNS queries). (Thanks for the suggestion Daniel and antenore.) Checked the routing tables (ip4 only as ipv6 is beyond my understanding) resetting all involved hardware (routers and modems) Close and reopen browsers Looked for malware interference: Run HijackThis Looked for suspicious processes using SysInternals procexp. Looked for explorer hijacks, lsa provider interference, winsock provider interference using SysInternals Autoruns. Run a complete anti-virus scan. Reviewed the output of a netstat -onab to see if there were stuck ports open or unusual processes running somewhere The only thing that works is to do a full reboot. That works 100% of the time to restore browsing. What else can I try to nail down the problem?

    Read the article

< Previous Page | 650 651 652 653 654 655 656 657 658 659 660 661  | Next Page >