Search Results

Search found 19009 results on 761 pages for 'network shares'.

Page 655/761 | < Previous Page | 651 652 653 654 655 656 657 658 659 660 661 662  | Next Page >

• I can't download or stream for more then 3 sec, and then the conection activity just dies

  - by JMHein

  Just got a new internet connection installed at my sisters place, but it randomly just stops working. At first it was only affecting flash videos. they would randomly just stop buffering. I did a lot of research on this and found that there can be many things that cause this exact trouble. I then tried IE and some flash would stream fine, but still random deaths. So I told my brother in law to reset the router and modem and that fixed the problem for them but not my laptop. I then started trying to fix the flash problem only to fined that downloads of any kind were affected. Now it is so bad that 50% of page loads will never finish because the connection drops to 0% usage with in a split sec. I can't get flash reinstalled because the installer is trying to download but the download dies at 8% I tried up loading a large file by FTP to a web server with no troubles. Yet any activity on my end that takes longer then about 1 sec to finish, just never finishes I can watch the network log in the taskmanager and it spikes for ruffly one sec then drops back to zero and when I go back to the web page it says it is still loading and no matter how long I let it sit it never does any thing more till I reload then it will again create a very short spike of activity on the connection and then drop to zero. Also if I start a download and it does drop off I can restart the download where it left off and get up to 100Kb/s for around the same one sec then it drops to around 14Kb/s then zero a sec latter... I am running Win 7 home prem x64 with FF11 and IE8 I have simply tried every thing I can short of calling up the ISP which very likely will get me no where fast. any advice on what step to take to figure this out would be nice. I am not even sure it is not just an ISP problem. (at least I should be able to get flash reinstalled once I get back home)

  Read the article

• Rack layout for future growth

  - by bleything

  We're getting ready to move to a new colo facility and I'm designing the rack layout. While we have a full rack, we only have 12U worth of hardware right now: 1x 1U switch 7x 1U servers 1x 2U server 1x 2U disk shelf The colo facility requires us to front-mount the switch and use a 1U brush strip, so we'll be using a total of 13U of space. Regarding growth, I'm reasonably sure we'll be adding another 4U in servers, 1-2U of network gear, and 2-4U of storage in the mid-term. Specific questions I'm hoping to get help with: where should I mount the switch? the LEDs are on top... should I group the servers by function with space for adding new machines? as an alternative, should I group servers based on whether they are production or staging? where in the rack should I start? in the middle? at the top? at the bottom? equally spaced? Here's a silly little ASCII diagram of what I'm thinking right now. Please feel free to tear my design apart, I've really no idea what I'm doing :) Any advice is very welcome. edit: to be clear, the colo is providing redundant power with UPS and generator, so that's why there's no power gear in the plan, except for the 0U PDU that I didn't diagram. 42 | -- switch ---------------------- 41 | -- brush strip ----------------- 40 | ~~ reserved for second switch ~~ 39 | ~~ reserved for firewall ~~~~~~~ 38 | 37 | -- admin01 --------------------- 36 | 35 | -- vm01 ------------------------ 34 | -- vm02 ------------------------ 33 | ~~ reserved for vm03 ~~~~~~~~~~~ 32 | ~~ reserved for vm04 ~~~~~~~~~~~ 31 | ~~ reserved for vm05 ~~~~~~~~~~~ 30 | 29 | -- web01 ----------------------- 28 | -- web02 ----------------------- 27 | ~~ reserved for web03 ~~~~~~~~~~ 26 | ~~ reserved for web04 ~~~~~~~~~~ 25 | 24 | 23 | 22 | 21 | 20 | 19 | 18 | 17 | 16 | -- db01 ------------------------ 15 | +- disks ----------------------+ 14 | +------------------------------+ 13 | ~~ reserved for more ~~~~~~~~~~~ 12 | ~~ db01 disks ~~~~~~~~~~~~~~~~~~ 11 | 10 | +- db02 -----------------------+ 9 | +------------------------------+ 8 | ~~ reserved for db02 ~~~~~~~~~~~ 7 | ~~ disks ~~~~~~~~~~~~~~~~~~~~~~~ 6 | ~~ reserved for more ~~~~~~~~~~~ 5 | ~~ db02 disks ~~~~~~~~~~~~~~~~~~ 4 | 3 | 2 | 1 |

  Read the article

• apache2: ssl_error_rx_record_too_long when visiting port 80? help!

  - by John

  Hi, I have an Ubuntu 10 x64 server edition machine. I got a second IP and configured /etc/network/interfaces like so (actual IPs and gateways removed): [code] auto lo iface lo inet loopback iface eth0 inet dhcp auto eth0 auto eth0:0 iface eth0 inet static address [ my first IP ] netmask 255.255.255.0 gateway [ my first gateway ] iface eth0:0 inet static address [ my second IP ] netmask 255.255.255.0 gateway [ my second gateway ] [/code] /etc/apache2/ports.conf: [code] Listen 80 NameVirtualHost [ my first IP ]:80 NameVirtualHost [ my second IP ]:80 # If you add NameVirtualHost *:443 here, you will also have to change # the VirtualHost statement in /etc/apache2/sites-available/default-ssl # to # Server Name Indication for SSL named virtual hosts is currently not # supported by MSIE on Windows XP. Listen 443 NameVirtualHost [ my first IP - some site is running SSL successfully using it ]:443 Listen 443 [/code] /etc/apache2/sites-enabled/mysite.conf: [code] ServerName mysite.com Include /var/www/mysite.com/djangoproject/apache/django.conf [/conf] [/code] Then when visiting http[mysite].com:80 or http[mysite].com (:// removed because serverfault doesn't allow me to post hyperlinks), I get: [code] An error occurred during a connection to [mysite].com. SSL received a record that exceeded the maximum permissible length. (Error code: ssl_error_rx_record_too_long) [/code] My guess is that the configuration file is not being picked up, and apache is therefore looking for the default-ssl file, which is not in conf-enabled. If I were to configure that file properly, it seems I would successfully connect to whatever default directory is specified in the default-ssl file. But I want to connect to my website. Any ideas? Thanks in advance!

  Read the article

• Intermittent unavailability of an instance in a failover cluster while a standby node is offline in

  - by Emil Fridriksson

  Hi everyone. I've got a small failover cluster that I run for the websites my company has. During a RAM upgrade of the standby server, our websites started to show errors about not being able to access the database server. I verified that the instance was indeed up and the server accessable via remote desktop. I also tried a SQL connection to it and it worked, but that might have been after it became available again. This happened on and off until we were able to roll back the hardware changes that were in progress on the standby server and we were able to bring it back up. There was nothing of interest in the SQL Server log, but there is a continous log for the whole duration of the problem, so there was no restart of the SQL Server service. The event viewer is of more interest, since it shows events relating to the heartbeat network card, but I don't know how that would affect the availability of the server, since the standby node is offline. I'd appreciate any help you can provide, it's not very redundant if the setup depends on the standby server being up. :) Here are the event logs from the time of the problem, I include all of them since I can't seem to see what could possibly be the cause of the problem. Event log: http://hlekkir.com:800/htmltable.htm

  Read the article

• A Domain Admin user doesn't have effective Administrative rights on a Domain Computer

  - by rwetzeler

  I am a developer who is setting up a virtual domain environment of testing purposes and am having trouble with the setup. I have created a new DC on a new Forest... call it dev.contoso.com. I have setup a virtual internal network for all machines that are going to be apart of this virtual test environment and have given each machine a static IP address in the 192.169.150.0 subnet. I have added machine1.dev.contoso.com to the domain dev.contoso.com. I have also provisioned a user account (adminuser) in the domain and made that user a member of Domain Admins group. Upon logging into machine1 using my newly created Domain Admin account, I cannot access/run any files on machine1. When I go into the advanced permissions for the c:\ folder and goto properties - Security Tab - Advanced - Effective Permissions and search for the dev\adminuser (mentioned above), I get an error saying: Windows can't calculate the effective permissions for admin user What do I need to do to get Administrative rights on Machine1? I am using Server 2008 R2 for both the AD controller and machine1.

  Read the article

• Samba between Ubuntu server 10.10 and Windows Vista, Windows 7

  - by chepukha

  Hi all, I have a linux box running Linux server ubuntu 10.10. I have installed Samba on this linux box and want to share files with my laptops which run Windows Vista home and Windows 7 home. I have been struggling with the setup for almost a month but couldn't get it right. If I try to access share folder from Windows Vista, I get message "Windows cannot access \\server_ip_address". Error code: 0x80070035. The network path was not found. If I access from Windows 7, then after entering password to login I can see the list of share folders on Linux box. But if I click on a share folder, I get the same error message as above. Tail /var/log/samba/log.windows7-pc I got the following message: [2011/03/16 00:17:41.427238, 0] smbd/service.c:988(make_connection_snum) canonicalize_connect_path failed for service sharemedia, path /root/sharemedia Here is my setting in smb.conf [global] share modes = yes netbios name = Samba workgroup = WORKGROUP wins support = yes encrypt passwords = true [sharemedia] comment = Tesing sharing using Samba path=/root/sharemedia/ public = yes valid users = samba_usr_name ; make sure all files are sensible permissions create mask = 0660 force create mask = 0660 directory mask = 2770 force directory mask = 2770 directory security mask = 0000 ; Normal share parameters read only = no browseable = yes writable = yes guest ok = no

  Read the article

• nameserver spoiling avahi multicast name resolution of .local domain

  - by Doug Coburn

  After trying to ping a machine on my local network, I noticed that I was trying hit address 66.152.109.24. This is an external public address. Resolution should have occurred via avahi mDNS. I ran dig to see how the name resolution worked and my quest/centurylink name server was retuning results for my .local domain queries! I tried a random name and got the same ip address result. $ dig jakdafj.local ; <<>> DiG 9.8.1-P1-RedHat-9.8.1-3.P1.fc15 <<>> jakdafj.local ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 58410 ;; flags: qr rd ra; QUERY: 1, ANSWER: 2, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;jakdafj.local. IN A ;; ANSWER SECTION: jakdafj.local. 10 IN A 66.152.109.24 jakdafj.local. 10 IN A 204.232.231.46 ;; Query time: 104 msec ;; SERVER: 205.171.3.25#53(205.171.3.25) ;; WHEN: Sat Mar 24 20:40:17 2012 ;; MSG SIZE rcvd: 63 Am I missing something or is my DNS name server at 205.171.3.25 corrupted?

  Read the article

• IE9 will not navigate to some websites but Google Chrome can

  - by Storchburp

  Was recommended by a friend to ask for help here. I am using Internet Explorer 9. As of two days ago I was suddenly unable to navigate to any part of the following websites: www.computerandvideogames.com www.deviantart.com www.cnet.com However I can still access all of them normally through Google Chrome. I am on a college network but these sites are also accessible through fixed terminals provided by the school and are definitely not blocked. I do not know of any other sites similarly affected. There is no popup, no error message, no diversion to a site telling me I can't access / am blocked etc. I can be on www.google.com and attempt to access these sites through the URL or google search, and my cursor will just show the little moving blue wheel next to the arrow for a couple of seconds, and the page displayed on my browser will not change; ie. not navigating at all. Running antivirus software, changing proxy settings in IE, clearing cookies, unplugging/plugging in computer, restarting PC etc have not changed the situation. Any assistance or advice would be greatly appreciated. Thanks in advance.

  Read the article

• Exchange ActiveSync Exception

  - by Dmeglio

  One of the users on my network is having an issue with his iPhone syncing via ActiveSync. Overall it's working, but every now and then he gets a "Synchronization with your iPhone failed for 3 items." I asked him to go into OWA and turn on the Mobile Phone logging. I looked through the logs and this is what stood out to me: SyncCommand_GenerateResponsesXmlNode_AddChange_Exception : Microsoft.Exchange.Data.Storage.PropertyErrorException: Property: [{00062008-0000-0000-c000-000000000046}:0x8501] ReminderMinutesBeforeStartInternal, PropertyErrorCode: NotFound, PropertyErrorDescription: . at Microsoft.Exchange.Data.Storage.PropertyBag.ThrowIfPropertyError(StorePropertyDefinition propertyDefinition, Object propertyValue) at Microsoft.Exchange.Data.Storage.StoreObject.GetProperty(PropertyDefinition propertyDefinition) at Microsoft.Exchange.Data.Storage.MeetingMessage.get_Item(PropertyDefinition propertyDefinition) at Microsoft.Exchange.AirSync.SchemaConverter.XSO.XsoMeetingRequestProperty.get_NestedData() at Microsoft.Exchange.AirSync.SchemaConverter.AirSync.AirSyncMeetingRequestProperty.InternalCopyFrom(IProperty srcProperty) at Microsoft.Exchange.AirSync.SchemaConverter.AirSync.AirSyncProperty.CopyFrom(IProperty srcProperty) at Microsoft.Exchange.AirSync.SchemaConverter.AirSync.AirSyncDataObject.CopyFrom(IProperty srcRootProperty) at Microsoft.Exchange.AirSync.SyncCollection.ConvertServerToClientObject(ISyncItem syncItem, XmlNode airSyncParentNode, SyncOperation changeObject) at Microsoft.Exchange.AirSync.SyncCollection.GenerateCommandsXmlNode(XmlDocument xmlResponse, IAirSyncVersionFactory versionFactory, String deviceType, ProtocolLogger protocolLogger, MailboxLogger mailboxLogger) Does anyone have any idea what might cause this? We have 4 iPhone users connected to our Exchange via ActiveSync. Right now, this seems to be the only user experiencing this issue. I'd appreciate any help anyone can provide. Thanks.

  Read the article

• SQL Server 2005 - Linked Visual Foxpro Authorization

  - by John

  Here's the Scenario: We have an existing SQL 2000 Server that has a linked server to a share directory (on another server) containing Visual FoxPro tables; all connections work correctly. Porting the SQL 2000 server to a new SQL 2005 server results in questionable behavior: If you connect to the server, remotely, using Windows Authentication, you receive this error when running a query against the linked server: OLE DB provider "MSDASQL" for linked server "[linked server name]" returned message "[Microsoft][ODBC Visual FoxPro Driver]File 'MyTable.dbf' does not exist.". Msg 7350, Level 16, State 2, Line 2 Cannot get the column information from OLE DB provider "MSDASQL" for linked server "[linked server name]". However, logged in locally, the query works fine. The query also works correctly when logged in remotely, but using a SQL login. The only scenario I receive the error is when connected remotely, using windows authentication. As I mentioned before, this works on the SQL 2000 server, and both the old and new servers are running under the same network account (which has access to the folder the FoxPro files are in). Doing a little searching on the internet it looks like others have run into this situation, but I haven't found a resolution. Has anyone run into this before?

  Read the article

• How do I get a Mac to request a new IP address from another DHCP server running in parallel while Ne

  - by huyqt

  Hello, I have an interesting situation. I'm trying to us a Linux based machine to allow Mac's to Netboot (similiar to PXE boot) by running a DHCP service in parallel with the "global" DHCP server. The local DHCP server hands out IPs in a private subnet, e.g., 10.168.0.10-10.168.254-254, while the "global" DHCP server hands out IPs from the IP range 10.0.0.1 - 10.0.1.254. The local DHCP range is only supposed to be used in Preboot Execution Environment and Netboot. The local DHCP server is something I have control over, but I do not have access to the global DHCP server. I have a filter to only allow members with the vendor strings "AAPLBSDPC/i386" and "PXEClient". PXE works fine, but Netboot has a quirk. The Apple systems that haven't been connected to the network yet can Netboot fine. But once it grabs a "real" IP address from the global DHCP server, it will "save" it and request it the next time we want it to netboot (which the local dhcp server won't give it). This is what I want: Mar 30 10:52:28 dev01 dhcpd: DHCPDISCOVER from 34:15:xx:xx:xx:xx via eth1 Mar 30 10:52:29 dev01 dhcpd: DHCPOFFER on 10.168.222.46 to 34:15:xx:xx:xx:xx via eth1 Mar 30 10:52:31 dev01 dhcpd: DHCPREQUEST for 10.168.222.46 (10.168.0.1) from 34:15:xx:xx:xx:xx via eth1 Mar 30 10:52:31 dev01 dhcpd: DHCPACK on 10.168.222.46 to 34:15:xx:xx:xx:xx via eth1 Mar 30 10:52:32 dev01 in.tftpd[5890]: tftp: client does not accept options Mar 30 10:52:53 dev01 in.tftpd[5891]: tftp: client does not accept options Mar 30 10:52:53 dev01 in.tftpd[5893]: tftp: client does not accept options Mar 30 10:52:54 dev01 in.tftpd[5895]: tftp: client does not accept options This is what I get when it already has a "stored" IP: Mar 30 10:51:29 dev01 dhcpd: DHCPDISCOVER from 00:25:xx:xx:xx:xx via eth1 Mar 30 10:51:30 dev01 dhcpd: DHCPOFFER on 10.168.222.45 to 00:25:xx:xx:xx:xx via eth1 Mar 30 10:51:31 dev01 dhcpd: DHCPREQUEST for 10.0.0.61 (10.0.0.1) from 00:25:xx:xx:xx:xx via eth1: ignored (not authoritative). Do you have any suggestions? It would be much appreciated.

  Read the article

• Windows 7 deployment thru WDS

  - by vn

  Hello, I am deploying new systems on my network and I built my reference computer by installing the OS the manufacturers (Dell and a custom built system from some local business) gave with all drivers, installed all the desired applications. As for the settings part, I'm doing most of it thru GPOs. I want to image my reference computer and deploy it with WDS. i found several links on how to sysprep, but they're all doing it with some differences without explaining them. My questions : How do I manage (into sysprep) the domain join/computer naming part since (from what I understand) WDS manages that? How do I know/determine what I need to setup into my sysprep.xml? Can you sysprep a first time, try and if it fails, do some modifications and try again? I am thinking of doing a basis sysprep, checking what info can be automated and correct that in the answer file. What do I miss if skipping the "audit" mode? I don't plan on re-doing the reference computer... I read that when sysprepping, it resets settings from the reference computer like the computer name, activation/key and such... what setting is sysprep resetting by default that I should be aware of? I must admit I am quite lost about Win7, sysprep, RIS, MDI toolkit, WDS.. I understand the way of doing with XP, but it changed so much with Windows 7! The links I am reading are : http://far2paranoid.wordpress.com/2007/12/05/prep-for-sysprep/ http://blog.brianleejackson.com/sysprep-a-windows-7-machine-%E2%80%93-start-to-finish-v2 http://www.ehow.com/print/how_5392616_sysprep-machine-start-finish-v2.html Thank you VERY much for any answers, they are much appreciated.

  Read the article

• Route forwarded traffic through eth0 but local traffic through tun0

  - by Ross Patterson

  I have a Ubuntu 12.04/Zentyal 2.3 server configured with WAN NATed on eth0, local interfaces eth1 and wlan0 bridged on br1 on which DHCP runs, and an OpenVPN connection on tun0. I only need the VPN for some things running on the gateway itself and I need to make sure that everything running on the gateway goes through the VPNs tun0. root:~# route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface default gw... 0.0.0.0 UG 100 0 0 eth0 link-local * 255.255.0.0 U 1000 0 0 br1 192.168.1.0 * 255.255.255.0 U 0 0 0 br1 A.B.C.0 * 255.255.255.0 U 0 0 0 eth0 root:~# ip route 169.254.0.0/16 dev br1 scope link metric 1000 192.168.1.0/24 dev br1 proto kernel scope link src 192.168.1.1 A.B.C.0/24 dev eth0 proto kernel scope link src A.B.C.186 root:~# ip route show table main 169.254.0.0/16 dev br1 scope link metric 1000 192.168.1.0/24 dev br1 proto kernel scope link src 192.168.1.1 A.B.C.0/24 dev eth0 proto kernel scope link src A.B.C.D root:~# ip route show table default default via A.B.C.1 dev eth0 How can I configure routing (or otherwise) such that all forwarded traffic for other hosts on the LAN goes through eth0 but all traffic for the gateway itself goes through the VPN on tun0? Also, since the OpenVPN client changes routing on startup/shutdown, how can I make sure that everything running on the gateway itself loses all network access if the VPN goes down and never goes out eth0.

  Read the article

• SPF record for Gmail?

  - by Chris

  I have DNS, with a SPF TXT record, configured for a domain name. The primary user of the domain name now needs to be able to send both from our SMTP servers, and also from her GMail account. I've seen all the information about adding "include:_spf.google.com" to the SPF TXT record, but, as I look into it, it appears that record is outdated. In particular, I had the user send me a test message, and note that it was: Received: from mail-la0-f50.google.com (mail-la0-f50.google.com [209.85.215.50]) However, _spf.google.com doesn't list that IP address: $ dig +short _spf.google.com txt "v=spf1 ip4:216.239.32.0/19 ip4:64.233.160.0/19 ip4:66.249.80.0/20 ip4:72.14.192.0/18 ip4:209.85.128.0/17 ip4:66.102.0.0/20 ip4:74.125.0.0/16 ip4:64.18.0.0/20 ip4:207.126.144.0/20 ip4:173.194.0.0/16 ?all" (Note that a 209.85.21*8*.0 network is listed, but not 209.85.21*5*.0.) Is there a better way to enable sending from GMail? This user sends to at least one recipient with a strict SPF policy that bounces mail not from a designated host... Many thanks!

  Read the article

• Does water damage a fiber optic / cat5 cable

  - by chris

  One of the buildings I support recently had an adventure with a broken fire sprinkler. Lots of water everywhere. One of the "drains" the water used was the vertical risers between network closets. The cable plant in this building has bundles of cat5e as well as conduit with bundles of multimode fiber optic cables. The fiber is standard multi strand plenum rated stuff that terminates in boxes that have the patches to the switches. As far as I can tell, no water got near the ends of the cables (fiber or copper) but the conduit was saturated, and is likely still saturated because there isn't any air flow to dry the cables out. My gut reaction is that while it didn't do the cables any favors, it likely also isn't going to cause any problems. A little more reading / googling around leads me to believe that the water may cause problems down the road. Some pretty pictures so everyone knows what I'm talking about: Fiber conduit: Vertical riser, going down: Vertical riser, going up: Does anyone have any experience with this sort of damage and how to deal with it? Should we just ask the insurance adjuster to add "pull new structured cable" to the list of things to be replaced? And, if the opinion is "replace it because it'll start failing randomly over time" please include links that describe the specific failure modes, so I've got some ammo to use with the adjuster.

  Read the article

• Remote Desktop access Windows 7 system from Windows 8

  - by Prabhat

  I have 2 systems; Windows 7 & Windows 8. Both are connected to WiFi router. They have been assigned address 192.168.2.8 & 192.168.2.9 respectively. I have added them to home group. I am able to ping and connect Windows 8 system from Windows 7. I am having trouble connecting Windows 7 system from Windows 8 system. I can't even ping Windows 7 system. Windows 7 system's user is administrator (default administrator account from secpol.msc). File sharing, Remote Access, network discovery are all enabled. Someone please help me connect. EDIT : I found that this is the issue of Kaspersky Internet Security 2012. If I disable firewall, it works. I tried opening port 3389 in Kaspersky. It is still blocking access.

  Read the article

• Configure Domino to use SMTP routing and hMailServer

  - by Sébastien Lachance

  I have been trying for a couple of days to set up a Domino 8.5 server. Basically, I want everything to be run inside a local network. Right now I can send email to other user in the Domino directory without any mail address. I am pretty new to all this stuff, so maybe the answer will be really obvious. What I need to do is be able to send a mail from somewhere else to a domino user that will be redirected to his account. On the Domino server, I also have hMailServer installed on port 25. I configured Domino to use port 26. I followed those step to get where I am now. -I have set the Fully qualified Internet host name to "preview.notes". -Smtp Listener task changed to Enabled to turn on the Listener so that the server can receive messages routed via SMTP routing -Setting up SMTP routing within the local Internet domain (http://www.h2l.com/help/help85%5Fadmin.nsf/f4b82fbb75e942a6852566ac0037f284/7f9738a49efc4f58852574d500097b01?OpenDocument) -I modified the person to use the [email protected] address. -I'm using the hMailServer (which have the local "preview.local" domain name) to send mail to [email protected]. When sending mail I got an error telling that the DNS is not set up correctly. Is using the Domino Smtp server instead of hMailServer will solve the problem? I can Telnet the Domino Smtp Server.

  Read the article

• NAT ports - how do they work?

  - by Davidoper

  I have the following network schema: Computer A: three nics: NIC 1 (eth0): dhcp, public internet NIC 2 (eth1): static 192.168.1.1, gateway for Computer B NIC 3 (eth2): static 192.168.2.1, gateway for Computer C Computer B: static 192.168.1.2, using gateway 192.168.1.1 (NIC 2). Computer C: static 192.168.2.2, using gateway 192.168.2.1 (NIC 3). So I applied this to get NAT working: iptables -t nat -A POSTROUTING -o eth0 -j MASQUERADE Every computer can connect to the internet now. I have been applying rules to the main computer (Computer A), like dropping connections to some ports, e.g ssh: iptables -A INPUT -p tcp --dport 22 -j DROP But for instance, now I would like only allow connections for ports 20,21,22,53 and 80 in Computer C, and ignore the outside traffic if it's not related to those ports. The allowed connections should be FROM Computer C to outside, but not from outside to Computer C (I mean - Computer C is not hosting any HTTP or SSH, but it is going to use them as a client). I guess this sould be done like this: iptables -A OUTPUT -i eth2 -o eth0 -p tcp --dport 21 -m state --state NEW,ESTABLISHED -j ACCEPT iptables -A INPUT -i eth2 -o eth0 -p tcp --sport 21 -m state --state ESTABLISHED -j ACCEPT The last rule (dropping any other traffic different from those) is at the end of the configuration, so -A should be working correctly. The thing is... it is not working. If I put the last rule like this: iptables -A FORWARD -i eth2 -o eth0 -j DROP It just drops everything and, for instance, port 21 (previously opened as you can see above) is not either working. Can you tell me what could I have done wrong? I have been struggling with this problem for some time and I am unable to solve it. Thanks!

  Read the article

• vagrant and puppet security for ssl certificates

  - by Sirex

  I'm pretty new to vagrant, would someone who knows more about it (and puppet) be able to explain how vagrant deals with the ssl certs needed when making vagrant testing machines that are processing the same node definition as the real production machines ? I run puppet in master / client mode, and I wish to spin up a vagrant version of my puppet production nodes, primarily to test new puppet code against. If my production machine is, say, sql.domain.com I spin up a vagrant machine of, say, sql.vagrant.domain.com. In the vagrant file I then use the puppet_server provisioner, and give a puppet.puppet_node entry of “sql.domain.com” to it gets the same puppet node definition. On the puppet server I use a regex of something like /*.sql.domain.com/ on that node entry so that both the vagrant machine and the real one get that node entry on the puppet server. Finally, I enable auto-signing for *.vagrant.domain.com in puppet's autosign.conf, so the vagrant machine gets signed. So far, so good... However: If one machine on my network gets rooted, say, unimportant.domain.com, what's to stop the attacker changing the hostname on that machine to sql.vagrant.domain.com, deleting the old puppet ssl cert off of it and then re-run puppet with a given node name of sql.domain.com ? The new ssl cert would be autosigned by puppet, match the node name regex, and then this hacked node would get all the juicy information intended for the sql machine ?! One solution I can think of is to avoid autosigning, and put the known puppet ssl cert for the real production machine into the vagrant shared directory, and then have a vagrant ssh job move it into place. The downside of this is I end up with all my ssl certs for each production machine sitting in one git repo (my vagrant repo) and thereby on each developer's machine – which may or may not be an issue, but it dosen't sound like the right way of doing this. tl;dr: How do other people deal with vagrant & puppet ssl certificates for development or testing clones of production machines ?

  Read the article

• Change the default route without affecting existing TCP connections

  - by Patrick Horn

  Let's say I have two public network addresses on my server: one NAT through an ISP (192.168.99.0/24), and a VPN through a different ISP (192.168.1.0/24), already configured with a per-host route to the VPN server through my ISP. Here is my initial routing table. I am currently routing through my ISP on subnet 192.168.99.0/24. $ route -n Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 0.0.0.0 192.168.99.1 0.0.0.0 UG 0 0 0 eth1 55.66.77.88 192.168.99.1 255.255.255.255 UGH 0 0 0 eth1 192.168.99.0 0.0.0.0 255.255.255.0 U 0 0 0 eth1 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 tap0 Now, I want new TCP connections to switch to my 192.168.1.0/24 so I type the following: $ route add -net 0.0.0.0 gw 192.168.1.1 dev tap0 When I do this, it causes some long-standing TCP connections to hang. Is there a way to I safely change the default interface for new connections, while allowing existing TCP connections to use the old route (i.e. do I need enable some sort of stateful routing table)? I am okay with a solution that only works with established TCP connections, and I don't care how hacky it is. For example, if there is a way to add temporary iptables rules for existing connections to force them over the old route. But there has to be some way to do this. EDIT: Just a note about a simple "route add -host ... " for existing connections: this solution would work if I am fine with leaving a subset of IPs on the old interface. However, in my application, this actually doesn't solve my problem because I want to allow new connections to come on the new interface even if they have the same source IP. I'm now looking at using the "ip route" command to set source-based routing rules.

  Read the article

• Cannot access host from a virtualbox guest using bridged adapter

  - by David Dai

  I have a windows 7 host with firewall turned off. And I have a windowsXP guest running on Virtualbox 4.2.4r81684. In my windowsXP guest I tried to connect to the FTP server on my host machine(which used to work well) but it didn't work. I tried to ping my host machine, but it didn't work either. Then I tried to ping my guest from host, it worked well. my guest ip is :192.168.1.95 my host ip is : 192.168.1.9 route table on guest machine is this: C:\Documents and Settings\wenlong>route PRINT =========================================================================== Interface List 0x1 ........................... MS TCP Loopback interface 0x2 ...08 00 27 66 54 6c ...... AMD PCNET Family PCI Ethernet Adapter #2 - Packe t Scheduler Miniport =========================================================================== =========================================================================== Active Routes: Network Destination Netmask Gateway Interface Metric 0.0.0.0 0.0.0.0 192.168.1.1 192.168.1.95 20 127.0.0.0 255.0.0.0 127.0.0.1 127.0.0.1 1 192.168.1.0 255.255.255.0 192.168.1.95 192.168.1.95 20 192.168.1.95 255.255.255.255 127.0.0.1 127.0.0.1 20 192.168.1.255 255.255.255.255 192.168.1.95 192.168.1.95 20 224.0.0.0 240.0.0.0 192.168.1.95 192.168.1.95 20 255.255.255.255 255.255.255.255 192.168.1.95 192.168.1.95 1 Default Gateway: 192.168.1.1 =========================================================================== Persistent Routes: None arp cache is this: C:\Documents and Settings\wenlong>arp -a Interface: 192.168.1.95 --- 0x2 Internet Address Physical Address Type 192.168.1.1 00-26-f2-60-3c-04 dynamic 192.168.1.9 90-e6-ba-c2-90-2f dynamic It's strange because there was no problem days before and I didn't make any changes to the setting. could anybody help? PS. the guest can communicate with other machines in the LAN(for example 192.168.1.114) ok. it just cannot connect to the host machine.

  Read the article

• Moving automatically spam messages to a folder in Postfix

  - by cad

  Hi My problem is that I want to automatically to move spam messages to a folder and not sure how. I have a linux box giving email access. MTA is Postfix, IMAP is Courier. As webmail client I use Squirrelmail. To filter SPAM I use Spamassassin and is working ok. Spamassasin is overwriting subjects with [--- SPAM 14.3 ---] Viagra... Also is adding headers: X-Spam-Flag: YES X-Spam-Checker-Version: SpamAssassin 3.2.5 (2008-06-10) on xxxx X-Spam-Level: ************** X-Spam-Status: Yes, score=14.3 required=2.0 tests=BAYES_99, DATE_IN_FUTURE_24_48,HTML_MESSAGE,MIME_HTML_ONLY,RCVD_IN_PBL, RCVD_IN_SORBS_WEB,RCVD_IN_XBL,RDNS_NONE,URIBL_RED,URIBL_SBL autolearn=no version=3.2.5 X-Spam-Report: * 0.0 URIBL_RED Contains an URL listed in the URIBL redlist * [URIs: myimg.de] * 3.5 BAYES_99 BODY: Bayesian spam probability is 99 to 100% * [score: 1.0000] * 0.9 RCVD_IN_PBL RBL: Received via a relay in Spamhaus PBL * [113.170.131.234 listed in zen.spamhaus.org] * 3.0 RCVD_IN_XBL RBL: Received via a relay in Spamhaus XBL * 0.6 RCVD_IN_SORBS_WEB RBL: SORBS: sender is a abuseable web server * [113.170.131.234 listed in dnsbl.sorbs.net] * 3.2 DATE_IN_FUTURE_24_48 Date: is 24 to 48 hours after Received: date * 0.0 HTML_MESSAGE BODY: HTML included in message * 1.5 MIME_HTML_ONLY BODY: Message only has text/html MIME parts * 1.5 URIBL_SBL Contains an URL listed in the SBL blocklist * [URIs: myimg.de] * 0.1 RDNS_NONE Delivered to trusted network by a host with no rDNS I want to automatically to move spam messages to a folder. Ideally (not sure if possible) only to move messages with puntuation 5.0 or more to folder.. spam between 2.0 and 5.0 I want to be stored in Inbox. (I plan later to switch autolearn on) After reading a lot in procmail, postfix and spamassasin sites and googling a lot (lot of outdated howtos) I found two solutions but not sure which is the best or if there is another one: Put a rule in squirrelmail (dirty solution?) Use Procmail Which is the best option? Do you have any updated howto about it? Thanks

  Read the article

• Apple Service Diagnostic application on USB key?

  - by Matt 'Trouble' Esse

  I found the following in a text file, and I would like to use the Apple Service Diagnostic Application from a bootable USB key but I cannot find where to download it or set it up? Also is this free software or does it require a separate licence? It sounds like it would be a useful tool for diagnosing Mac problems. The Apple Service Diagnostic application is designed to run both EFI and Mac OS X tests from an external USB hard drive. Apple Service Diagnostic (EFI) runs low-level tests of the hardware directly and does not require Mac OS X, while Apple Service Diagnostic (OS) uses Mac OS X to run tests. Booting and Using the Apple Service Diagnostic Application - Before using Apple Service Diagnostic, disconnect any Ethernet network, USB, and audio cables. - With the USB hard drive containing ASD 3S123 plugged into a USB port, restart the computer and hold down the option key as the computer boots up into the Startup Manager. To run ASD (EFI) select the "ASD EFI 3S123" drive icon and press return or select it with a mouse click. To run ASD (OS) select the "ASD OS 3S123" drive icon and press return or select it with a mouse click. ASD (EFI) will load in 20-30 seconds; ASD (OS) will load in 2-3 minutes. - After running ASD (OS) or ASD (EFI), press the Restart button to restart the computer back into the normal startup volume, or hold down the option key to get back to the Startup Manager. ASD is no longer delivered as an image to be restored onto a DVD. ASD 3S117 and newer versions requires installation onto an external USB hard drive. For more information, please refer to the document "Installing ASD on a USB hard drive".

  Read the article

• Workstations cannot see new MS Server 2008 domain, but can access DHCP.

  - by Radix

  The XP Pro workstations do not see the new replacement domain upon boot; they only see their cached entry for the old (server 2003) domain controller. The old_server is not connected to the network. I have DHCP working with the same scope as the old_server. In my "before-asking" search for a solution I came across the following two articles, and I recall doing things as suggested by the articles. http://www.windowsreference.com/windows-server-2008/how-to-setup-dhcp-server-in-windows-server-2008-step-by-step-guide/ http://www.windowsreference.com/windows-server-2008/step-by-step-guide-for-windows-server-2008-domain-controller-and-dns-server-setup/ The only possible issue is: I was under the impression that the domain netbios needed to match the DC's netbios. The DC netbios is city01 while the domain's FQDN is city.domain.org (I think this is mistaken and should have been just domain.org) But, the second link led me to a post which I believe answers my question. I did as they instructed by opening Local Area Connection Properties, then selecting TCP/IPv4 and setting the sole preferred DNS server to the local hosts static IP (10.10.1.1). Search for "Your problems should clear up" for the post I'm referencing: http://forums.techarena.in/active-directory/1032797.htm Have I misunderstood their instructions? I am hoping to reach the point where I can define users and user groups. Also, does TechNet have a single theoretical overview document I could read. I really don't like treating comps as magic. I will be watching this closely and will quickly answer any questions. If I've left anything out it is because I did not know it was needed. PS: I am loath to ask obviously basic questions, but I am tired and wish to fix this before tomorrow. Also, this is my first server installation, thank you for your help.

  Read the article

• F5 Networks iRule/Tcl - Escaping UNICODE 6-character escape sequences so they are processed as and r

  - by openid.malcolmgin.com

  We are trying to get an F5 BIG-IP LTM iRule working properly with SharePoint 2007 in an SSL termination role. This architecture offloads all of the SSL processing to the F5 and the F5 forwards interactive requests/responses to the SharePoint front end servers via HTTP only (over a secure network). For the purposes of this discussion, iRules are parsed by a Tcl interpretation engine on the F5 Networks BIG-IP device. As such, the F5 does two things to traffic passing through it: Redirects any request to port 80 (HTTP) to port 443 (HTTPS) through HTTP 302 redirects and URL rewriting. Rewrites any response to the browser to selectively rewrite URLs embedded within the HTML so that they go to port 443 (HTTPS). This prevents the 302 redirects from breaking DHTML generated by SharePoint. We've got part 1 working fine. The main problem with part 2 is that in the response rewrite because of XML namespaces and other similar issues, not ALL matches for "http:" can be changed to "https:". Some have to remain "http:". Additionally, some of the "http:" URLs are difficult in that they live in SharePoint-generated JavaScript and their slashes (i.e. "/") are actually represented in the HTML by the UNICODE 6-character string, "\u002f". For example, in the case of these tricky ones, the literal string in the outgoing HTML is: http:\u002f\u002fservername.company.com\u002f And should be changed to: https:\u002f\u002fservername.company.com\u002f Currently we can't even figure out how to get a match in a search/replace expression on these UNICODE sequence string literals. It seems that no matter how we slice it, the Tcl interpreter is interpreting the "\u002f" string into the "/" translation before it does anything else. We've tried various combinations of Tcl escaping methods we know about (mainly double-quotes and using an extra "\" to escape the "\" in the UNICODE string) but are looking for more methods, preferably ones that work. Does anyone have any ideas or any pointers to where we can effectively self-educate about this? Thanks very much in advance.

  Read the article

< Previous Page | 651 652 653 654 655 656 657 658 659 660 661 662  | Next Page >