Search Results

Search found 17003 results on 681 pages for 'multi index'.

Page 658/681 | < Previous Page | 654 655 656 657 658 659 660 661 662 663 664 665  | Next Page >

• Outbound traffic being blocked for MIP/VIPped servers (Juniper SSG5)

  - by Mark S. Rasmussen

  As we've been having some problems with sporadic packet loss, I've been preparing a replacement router (also an SSG5) for our current Juniper SSG5. I've setup the new SSG5 identically to the old one. We have a /29 IP range with a single IP setup as a MIP map to a server and two others being used for VIP maps. Each VIP/MIP is accompanied by relevant policies. Long story short - we tried connected the new SSG5 and some things were not working as they should. No problem, I just reconnected the old one. However, some things are still broken, even when I reconnected the old one. I fear I may have inadvertently changed some settings while browsing through old settings in my attempt to reconfigure the new SSG5 unit. All inbound traffic seems to work as expected. However, the 192.168.2.202 server can't initiate any outbound connections. It works perfectly on the local network, but any pings or DNS lookups to external IP's fail. The MIP & VIP map to it works perfectly - I can access it through HTTP and RDP without issues. Any tips on what to debug, or where I've messed up my config? I've attached the full config here (with anonymized IPs): set clock timezone 1 set vrouter trust-vr sharable set vrouter "untrust-vr" exit set vrouter "trust-vr" unset auto-route-export exit set service "MyVOIP_UDP4569" protocol udp src-port 0-65535 dst-port 4569-4569 set service "MyVOIP_TCP22" protocol tcp src-port 0-65535 dst-port 22-22 set service "MyRDP" protocol tcp src-port 0-65535 dst-port 3389-3389 set service "MyRsync" protocol tcp src-port 0-65535 dst-port 873-873 set service "NZ_FTP" protocol tcp src-port 0-65535 dst-port 40000-41000 set service "NZ_FTP" + tcp src-port 0-65535 dst-port 21-21 set service "PPTP-VPN" protocol 47 src-port 2048-2048 dst-port 2048-2048 set service "PPTP-VPN" + tcp src-port 1024-65535 dst-port 1723-1723 set service "NZ_FMS_1935" protocol tcp src-port 0-65535 dst-port 1935-1935 set service "NZ_FMS_1935" + udp src-port 0-65535 dst-port 1935-1935 set service "NZ_FMS_8080" protocol tcp src-port 0-65535 dst-port 8080-8080 set service "CrashPlan Server" protocol tcp src-port 0-65535 dst-port 4280-4280 set service "CrashPlan Console" protocol tcp src-port 0-65535 dst-port 4282-4282 unset alg sip enable set auth-server "Local" id 0 set auth-server "Local" server-name "Local" set auth default auth server "Local" set auth radius accounting port 1646 set admin auth timeout 10 set admin auth server "Local" set admin format dos set vip multi-port set zone "Trust" vrouter "trust-vr" set zone "Untrust" vrouter "trust-vr" set zone "DMZ" vrouter "trust-vr" set zone "VLAN" vrouter "trust-vr" set zone "Untrust-Tun" vrouter "trust-vr" set zone "Trust" tcp-rst set zone "Untrust" block unset zone "Untrust" tcp-rst set zone "DMZ" tcp-rst set zone "VLAN" block unset zone "VLAN" tcp-rst set zone "Untrust" screen tear-drop set zone "Untrust" screen syn-flood set zone "Untrust" screen ping-death set zone "Untrust" screen ip-filter-src set zone "Untrust" screen land set zone "V1-Untrust" screen tear-drop set zone "V1-Untrust" screen syn-flood set zone "V1-Untrust" screen ping-death set zone "V1-Untrust" screen ip-filter-src set zone "V1-Untrust" screen land set interface ethernet0/0 phy full 100mb set interface ethernet0/3 phy full 100mb set interface ethernet0/4 phy full 100mb set interface ethernet0/5 phy full 100mb set interface ethernet0/6 phy full 100mb set interface "ethernet0/0" zone "Untrust" set interface "ethernet0/1" zone "Null" set interface "bgroup0" zone "Trust" set interface "bgroup1" zone "Trust" set interface "bgroup2" zone "Trust" set interface bgroup2 port ethernet0/2 set interface bgroup0 port ethernet0/3 set interface bgroup0 port ethernet0/4 set interface bgroup1 port ethernet0/5 set interface bgroup1 port ethernet0/6 unset interface vlan1 ip set interface ethernet0/0 ip 212.242.193.18/29 set interface ethernet0/0 route set interface bgroup0 ip 192.168.1.1/24 set interface bgroup0 nat set interface bgroup1 ip 192.168.2.1/24 set interface bgroup1 nat set interface bgroup2 ip 192.168.3.1/24 set interface bgroup2 nat set interface ethernet0/0 gateway 212.242.193.17 unset interface vlan1 bypass-others-ipsec unset interface vlan1 bypass-non-ip set interface ethernet0/0 ip manageable set interface bgroup0 ip manageable set interface bgroup1 ip manageable set interface bgroup2 ip manageable set interface bgroup0 manage mtrace unset interface bgroup1 manage ssh unset interface bgroup1 manage telnet unset interface bgroup1 manage snmp unset interface bgroup1 manage ssl unset interface bgroup1 manage web unset interface bgroup2 manage ssh unset interface bgroup2 manage telnet unset interface bgroup2 manage snmp unset interface bgroup2 manage ssl unset interface bgroup2 manage web set interface ethernet0/0 vip 212.242.193.19 2048 "PPTP-VPN" 192.168.1.131 set interface ethernet0/0 vip 212.242.193.19 + 4280 "CrashPlan Server" 192.168.1.131 set interface ethernet0/0 vip 212.242.193.19 + 4282 "CrashPlan Console" 192.168.1.131 set interface ethernet0/0 vip 212.242.193.22 22 "MyVOIP_TCP22" 192.168.2.127 set interface ethernet0/0 vip 212.242.193.22 + 4569 "MyVOIP_UDP4569" 192.168.2.127 set interface ethernet0/0 vip 212.242.193.22 + 3389 "MyRDP" 192.168.2.202 set interface ethernet0/0 vip 212.242.193.22 + 873 "MyRsync" 192.168.2.201 set interface ethernet0/0 vip 212.242.193.22 + 80 "HTTP" 192.168.2.202 set interface ethernet0/0 vip 212.242.193.22 + 2048 "PPTP-VPN" 192.168.2.201 set interface ethernet0/0 vip 212.242.193.22 + 8080 "NZ_FMS_8080" 192.168.2.216 set interface ethernet0/0 vip 212.242.193.22 + 1935 "NZ_FMS_1935" 192.168.2.216 set interface bgroup0 dhcp server service set interface bgroup1 dhcp server service set interface bgroup2 dhcp server service set interface bgroup0 dhcp server auto set interface bgroup1 dhcp server auto set interface bgroup2 dhcp server auto set interface bgroup0 dhcp server option domainname iplan set interface bgroup0 dhcp server option dns1 192.168.1.131 set interface bgroup1 dhcp server option domainname nzlan set interface bgroup1 dhcp server option dns1 192.168.2.202 set interface bgroup2 dhcp server option dns1 8.8.8.8 set interface bgroup2 dhcp server option wins1 8.8.4.4 set interface bgroup0 dhcp server ip 192.168.1.2 to 192.168.1.116 set interface bgroup1 dhcp server ip 192.168.2.2 to 192.168.2.116 set interface bgroup2 dhcp server ip 192.168.3.2 to 192.168.3.126 unset interface bgroup0 dhcp server config next-server-ip unset interface bgroup1 dhcp server config next-server-ip unset interface bgroup2 dhcp server config next-server-ip set interface "ethernet0/0" mip 212.242.193.21 host 192.168.2.202 netmask 255.255.255.255 vr "trust-vr" set interface "serial0/0" modem settings "USR" init "AT&F" set interface "serial0/0" modem settings "USR" active set interface "serial0/0" modem speed 115200 set interface "serial0/0" modem retry 3 set interface "serial0/0" modem interval 10 set interface "serial0/0" modem idle-time 10 set pak-poll p1queue pak-threshold 96 set pak-poll p2queue pak-threshold 32 set flow tcp-mss unset flow tcp-syn-check set dns host dns1 0.0.0.0 set dns host dns2 0.0.0.0 set dns host dns3 0.0.0.0 set address "Trust" "192.168.1.0/24" 192.168.1.0 255.255.255.0 set address "Trust" "192.168.2.0/24" 192.168.2.0 255.255.255.0 set address "Trust" "192.168.3.0/24" 192.168.3.0 255.255.255.0 set ike respond-bad-spi 1 unset ike ikeid-enumeration unset ike dos-protection unset ipsec access-session enable set ipsec access-session maximum 5000 set ipsec access-session upper-threshold 0 set ipsec access-session lower-threshold 0 set ipsec access-session dead-p2-sa-timeout 0 unset ipsec access-session log-error unset ipsec access-session info-exch-connected unset ipsec access-session use-error-log set l2tp default ppp-auth chap set url protocol websense exit set policy id 1 from "Trust" to "Untrust" "Any" "Any" "ANY" permit traffic set policy id 1 exit set policy id 2 from "Untrust" to "Trust" "Any" "VIP(212.242.193.19)" "PPTP-VPN" permit traffic set policy id 2 exit set policy id 3 from "Untrust" to "Trust" "Any" "VIP(212.242.193.22)" "HTTP" permit traffic priority 0 set policy id 3 set service "MyRDP" set service "MyRsync" set service "MyVOIP_TCP22" set service "MyVOIP_UDP4569" exit set policy id 6 from "Trust" to "Trust" "192.168.1.0/24" "192.168.2.0/24" "ANY" deny set policy id 6 exit set policy id 7 from "Trust" to "Trust" "192.168.2.0/24" "192.168.1.0/24" "ANY" deny set policy id 7 exit set policy id 8 from "Trust" to "Trust" "192.168.3.0/24" "192.168.1.0/24" "ANY" deny set policy id 8 exit set policy id 9 from "Trust" to "Trust" "192.168.3.0/24" "192.168.2.0/24" "ANY" deny set policy id 9 exit set policy id 10 from "Untrust" to "Trust" "Any" "MIP(212.242.193.21)" "NZ_FTP" permit set policy id 10 exit set policy id 11 from "Untrust" to "Trust" "Any" "VIP(212.242.193.22)" "PPTP-VPN" permit set policy id 11 exit set policy id 12 from "Untrust" to "Trust" "Any" "VIP(212.242.193.22)" "NZ_FMS_1935" permit set policy id 12 set service "NZ_FMS_8080" exit set policy id 13 from "Untrust" to "Trust" "Any" "VIP(212.242.193.19)" "CrashPlan Console" permit set policy id 13 set service "CrashPlan Server" exit set nsmgmt bulkcli reboot-timeout 60 set ssh version v2 set config lock timeout 5 set snmp port listen 161 set snmp port trap 162 set vrouter "untrust-vr" exit set vrouter "trust-vr" unset add-default-route exit set vrouter "untrust-vr" exit set vrouter "trust-vr" exit

  Read the article

• KVM machine does not start ssh, network is started, used to work

  - by lleto

  have been searching an pulling my hear out for the last 6 hours. I have a virtual machine that has been running fine for the last six months. I was happy ssh'ing into it and it was running a database and some small apps. Tonight ssh stopped working, so I decided to reboot the machine. I now have the following situation: virsh list --all states machine as running I can ping the machine and get a reply When I ssh to the machine I see "ssh: connect to host [myserver] port 22: Connection refused" nmap does not show port 22 as open I have tried to: - reboot the machine once more (no luck) - mount the filesystem and check /etc/ssh/sshd.conf (has not changed since working situation) - install virsh console, however this does not seem to work When I mount the fs directly using losetup the strange thing is that file dates seem to be frozen in /var/log/ around the time of the crash. If I look in /var/run/ I can see an sshd.pid, but the time is 6 hours ago (and numerous reboots). My virsh xml looks like this: <domain type='kvm' id='21'> <name>myserver</name> <uuid>09678c8d-a99b-1d18-a7af-88d027cc8f93</uuid> <memory>1048576</memory> <currentMemory>1048576</currentMemory> <vcpu>1</vcpu> <os> <type arch='x86_64' machine='pc-1.0'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> </features> <clock offset='utc'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>destroy</on_crash> <devices> <emulator>/usr/bin/kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='raw'/> <source file='/dev/disk01/myserver'/> <target dev='hda' bus='ide'/> <alias name='ide0-0-0'/> <address type='drive' controller='0' bus='0' unit='0'/> </disk> <controller type='ide' index='0'> <alias name='ide0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x01' function='0x1'/> </controller> <interface type='bridge'> <mac address='52:54:00:e3:13:86'/> <source bridge='br0'/> <target dev='vnet0'/> <model type='virtio'/> <alias name='net0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x0'/> </interface> <serial type='pty'> <source path='/dev/pts/1'/> <target port='0'/> <alias name='serial0'/> </serial> <console type='pty' tty='/dev/pts/1'> <source path='/dev/pts/1'/> <target type='serial' port='0'/> <alias name='serial0'/> </console> <input type='mouse' bus='ps2'/> <graphics type='vnc' port='5900' autoport='yes' listen='127.0.0.1'> <listen type='address' address='127.0.0.1'/> </graphics> <video> <model type='cirrus' vram='9216' heads='1'/> <alias name='video0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x0'/> </video> <memballoon model='virtio'> <alias name='balloon0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x04' function='0x0'/> </memballoon> </devices> <seclabel type='dynamic' model='apparmor' relabel='yes'> <label>libvirt-09678c8d-a99b-1d18-a7af-88d027cc8f93</label> <imagelabel>libvirt-09678c8d-a99b-1d18-a7af-88d027cc8f93</imagelabel> </seclabel> </domain> I'm sort of lost as to where I can look to get the machine up and running again. On the same instance of kvm I have another server running which is working fine. Both are Ubuntu 12.04. All help is welcome....

  Read the article

• How to convert html textfield/area data to server-side txt file? [closed]

  - by olijake

  How can I make a script that will convert the text/data in a html textfield/textarea and send it to the server, which then saves it as a .txt file for storage? NOTE: I am hosting a website(for testing purposes) using Apache 2.2 on a Windows 7 machine. I downloaded PHP version 5.4.7, but have not yet installed on my server yet (not sure if I will need it, but also not sure how to install it). 1st problem: Saving text to server Html page/section with title textfield, text textarea, and submit button. You would enter a title, the text/notes you need in the textfield, then press the submit button to have it store the text in the textarea, as a .txt file on the server called .txt. 2nd problem: Opening text from server Html with list of all txt files OR textfield for entering in title, then submit button to send the title of the requested .txt file to the server, which would then load it up on the page. Here is what I have so far: (let me know if there is something that I should change or if something just isn't correct in the index.html code I have right now.) <!DOCTYPE HTML> <html> <head> <title>Insert Title</title> <meta http-equiv="Content-Type" content="Text/HTML; charset=UTF-8"/> </head> <body> <form method="post" action="save.INSERT_FILETYPE" name="textfile" enctype="multipart/form-data"> <input type="text" name="title"><br/> <textarea rows="20" cols="100" id="text" name="text"></textarea><br/> <input type="submit" name="submit" value="Submit Text to Server"> </form><br/> <hr style="width: 100%; height: 4px;"><br/> <form method="post" action="open.INSERT_FILETYPE" name="textfile" enctype="multipart/form-data"> <input type="text" name="title"><br/> <input type="submit" name="submit" value="Submit Txt File Request"> </form><br/> <div>Opened text file displays here or goes on another page</div> </body> </html> I plan on using a server side language/script, but ANYTHING that gets the job done is fine. I already tried looking into using some ASP/jScript/PHP, but have had some trouble implementing it into my server. (ie: getting the modules loaded and telling the server what file types to parse.) I know this may be an extremely easy fix, but then in that case, hopefully you wouldn't mind helping me out a little :). If it turns out that this is MUCH more complicated than I expect, then feel free to let me know that, so I don't waste me time running in circles. I appreciate any help/assistance that you can provide, Thanks, Jake EDIT: Wrong Apache version. In response to the comments/closing of this thread: My question: "How exactly do I install the PHP module on the apache server? and is this even possible? and is this even recommended?" ^ In case I wasn't clear enough already To Clarify: I understand the basics of PHP, I just have trouble with INSTALLING PHP on the apache server. (I have used PHP before, but never successfully on apache (so far...)) For my script I wrote something similar to this already (using fopen() and a few other commands): <?php fopen("notes.txt", "r"); file_put_contents("notes.txt",teststring1); ?> I have used javascript for this task before also (although I prefer using PHP and server-side languages): <script language="javascript"> function WriteToFile(){ var fso = new ActiveXObject("Scripting.FileSystemObject"); var s = fso.CreateTextFile("C:\\NewFile.txt", true); var text=document.getElementById("TextArea1").innerText; s.WriteLine(text); s.WriteLine('***********************'); s.Close(); } </script>

  Read the article

• iptables to allow 80 and 443 on chillispot running ddwrt

  - by user76682

  I am having problems setting this up. this is what I am trying to do. I have Chillispot (hotpsot) running on dd-wrt. Everything is setup, but the client wants only 80 and 443 to go through through the hotspot. I found this tutorial for dd-wrt but that doesnt seem to work. http://www.dd-wrt.com/wiki/index.php/Iptables#Allow_HTTP_traffic_only_to_specific_domain.28s.29 Initially I tried to place the options at the top but didnt work. then i flushed the iptables and set only these three. I can see the pkts number grow but for some reason I can browse. root@DD-WRT:~# iptables -nvL FORWARD Chain FORWARD (policy ACCEPT 3105 packets, 2442K bytes) pkts bytes target prot opt in out source destination 1629 230K ACCEPT tcp -- * * 0.0.0.0/0 0.0.0.0/0 multiport dports 21,80,443 2346 2792K ACCEPT 0 -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 328 46420 DROP 0 -- * * 0.0.0.0/0 0.0.0.0/0 Heres some info from the router, chillispot is the tun0 interface. root@DD-WRT:~# iptables -vnL FORWARD --line-numbers Chain FORWARD (policy DROP 0 packets, 0 bytes) num pkts bytes target prot opt in out source destination 1 0 0 ACCEPT 47 -- * vlan1 192.168.8.0/24 0.0.0.0/0 2 0 0 ACCEPT tcp -- * vlan1 192.168.8.0/24 0.0.0.0/0 tcp dpt:1723 3 32 1851 ACCEPT 0 -- tun0 * 0.0.0.0/0 0.0.0.0/0 state NEW 4 0 0 ACCEPT 0 -- br0 br0 0.0.0.0/0 0.0.0.0/0 5 48 2408 TCPMSS tcp -- * * 0.0.0.0/0 0.0.0.0/0 tcp flags:0x06/0x02 TCPMSS clamp to PMTU 6 756 452K lan2wan 0 -- * * 0.0.0.0/0 0.0.0.0/0 7 756 452K ACCEPT 0 -- * * 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED 8 0 0 TRIGGER 0 -- vlan1 br0 0.0.0.0/0 0.0.0.0/0 TRIGGER type:in match:0 relate:0 9 0 0 trigger_out 0 -- br0 * 0.0.0.0/0 0.0.0.0/0 10 0 0 ACCEPT 0 -- br0 * 0.0.0.0/0 0.0.0.0/0 state NEW 11 0 0 DROP 0 -- * * 0.0.0.0/0 0.0.0.0/0 12 0 0 DROP 0 -- br0 * 0.0.0.0/0 0.0.0.0/0 13 0 0 DROP 0 -- * br0 0.0.0.0/0 0.0.0.0/0 The interfaces: root@DD-WRT:~# ifconfig -a br0 Link encap:Ethernet HWaddr 00:12:17:CF:80:5F inet addr:192.168.8.1 Bcast:192.168.8.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2371 errors:0 dropped:0 overruns:0 frame:0 TX packets:1862 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:259721 (253.6 KiB) TX bytes:254862 (248.8 KiB) br0:0 Link encap:Ethernet HWaddr 00:12:17:CF:80:5F inet addr:169.254.255.1 Bcast:169.254.255.255 Mask:255.255.0.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 eth0 Link encap:Ethernet HWaddr 00:12:17:CF:80:5F UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:5050 errors:0 dropped:0 overruns:0 frame:0 TX packets:2508 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:1066410 (1.0 MiB) TX bytes:376001 (367.1 KiB) Interrupt:5 eth1 Link encap:Ethernet HWaddr 00:12:17:CF:80:61 UP BROADCAST RUNNING ALLMULTI MULTICAST MTU:1500 Metric:1 RX packets:729 errors:0 dropped:0 overruns:0 frame:114693 TX packets:697 errors:2 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:107869 (105.3 KiB) TX bytes:473134 (462.0 KiB) Interrupt:4 Base address:0x1000 etherip0 Link encap:Ethernet HWaddr 1E:13:B7:09:CC:8C BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 UP LOOPBACK RUNNING MULTICAST MTU:16436 Metric:1 RX packets:18 errors:0 dropped:0 overruns:0 frame:0 TX packets:18 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:1210 (1.1 KiB) TX bytes:1210 (1.1 KiB) teql0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 NOARP MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:100 RX bytes:0 (0.0 B) TX bytes:0 (0.0 B) tun0 Link encap:UNSPEC HWaddr 00-00-00-00-00-00-00-00-00-00-00-00-00-00-00-00 inet addr:192.168.182.1 P-t-P:192.168.182.1 Mask:255.255.255.0 UP POINTOPOINT RUNNING MTU:1500 Metric:1 RX packets:662 errors:0 dropped:0 overruns:0 frame:0 TX packets:587 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:10 RX bytes:92167 (90.0 KiB) TX bytes:427657 (417.6 KiB) vlan0 Link encap:Ethernet HWaddr 00:12:17:CF:80:5F UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2371 errors:0 dropped:0 overruns:0 frame:0 TX packets:1864 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:269558 (263.2 KiB) TX bytes:262680 (256.5 KiB) vlan1 Link encap:Ethernet HWaddr 00:12:17:CF:80:60 inet addr:10.3.2.47 Bcast:10.255.255.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:2675 errors:0 dropped:0 overruns:0 frame:0 TX packets:645 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:705429 (688.8 KiB) TX bytes:102197 (99.8 KiB) The routing table: root@DD-WRT:~# netstat -nr Kernel IP routing table Destination Gateway Genmask Flags MSS Window irtt Iface 192.168.182.0 0.0.0.0 255.255.255.0 U 0 0 0 tun0 10.3.2.0 0.0.0.0 255.255.255.0 U 0 0 0 vlan1 192.168.8.0 0.0.0.0 255.255.255.0 U 0 0 0 br0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 br0 127.0.0.0 0.0.0.0 255.0.0.0 U 0 0 0 lo 0.0.0.0 10.3.2.1 0.0.0.0 UG 0 0 0 vlan1 Highly appreciate your help. TIA, Arun

  Read the article

• Allowing connections initiated from outside

  - by Mark S. Rasmussen

  I've got an old Juniper SSG5 running ScreenOS 5.4.0r6.0. Once a day, more or less, it'll start randomly dropping packets at a rate of ~5-10%. We currently solve this issue by simply rebooting the unit, after which it resumes working in perfect condition. As this error has started appearing randomly, without any configuration or hardware changes, I'm assuming I've got an aging unit about to fail. As such, I've got a replacement SSG5 running ScreenOS 6.0. I've dumped the config on the 5.4 and imported it into a clean 6.0, and it seems to gladly accept it, and all my configuration seems to be A-OK. However, upon connecting the new unit, all outside-initiated connections seem to be blocked. If I browse our external IP from the inside, everything works perfectly, and it's not just port 80, SSH, Crashplan - all of our policies route correctly. All normal networking, initiated from the inside, work perfectly as well. If on the other hand I browse our external IP from the outside, everything is blocked. Barring differences between ScreenOS 5.4 and 6.0, the config is identical. Is there a setting somewhere that defines whether outside/inside initiated connections are allowed? unset key protection enable set clock timezone 1 set vrouter trust-vr sharable set vrouter "untrust-vr" exit set vrouter "trust-vr" unset auto-route-export exit set service "MyVOIP_UDP4569" protocol udp src-port 0-65535 dst-port 4569-4569 set service "MyVOIP_TCP22" protocol tcp src-port 0-65535 dst-port 22-22 set service "MyRDP" protocol tcp src-port 0-65535 dst-port 3389-3389 set service "MyRsync" protocol tcp src-port 0-65535 dst-port 873-873 set service "NZ_FTP" protocol tcp src-port 0-65535 dst-port 40000-41000 set service "NZ_FTP" + tcp src-port 0-65535 dst-port 21-21 set service "PPTP-VPN" protocol 47 src-port 2048-2048 dst-port 2048-2048 set service "PPTP-VPN" + tcp src-port 1024-65535 dst-port 1723-1723 set service "NZ_FMS_1935" protocol tcp src-port 0-65535 dst-port 1935-1935 set service "NZ_FMS_1935" + udp src-port 0-65535 dst-port 1935-1935 set service "NZ_FMS_8080" protocol tcp src-port 0-65535 dst-port 8080-8080 set service "CrashPlan Server" protocol tcp src-port 0-65535 dst-port 4280-4280 set service "CrashPlan Console" protocol tcp src-port 0-65535 dst-port 4282-4282 unset alg sip enable set alg appleichat enable unset alg appleichat re-assembly enable set alg sctp enable set auth-server "Local" id 0 set auth-server "Local" server-name "Local" set auth default auth server "Local" set auth radius accounting port 1646 set admin name "netscreen" set admin password "XXX" set admin auth web timeout 10 set admin auth dial-in timeout 3 set admin auth server "Local" set admin format dos set vip multi-port set zone "Trust" vrouter "trust-vr" set zone "Untrust" vrouter "trust-vr" set zone "DMZ" vrouter "trust-vr" set zone "VLAN" vrouter "trust-vr" set zone "Untrust-Tun" vrouter "trust-vr" set zone "Trust" tcp-rst set zone "Untrust" block unset zone "Untrust" tcp-rst set zone "MGT" block unset zone "V1-Trust" tcp-rst unset zone "V1-Untrust" tcp-rst set zone "DMZ" tcp-rst unset zone "V1-DMZ" tcp-rst unset zone "VLAN" tcp-rst set zone "Untrust" screen tear-drop set zone "Untrust" screen syn-flood set zone "Untrust" screen ping-death set zone "Untrust" screen ip-filter-src set zone "Untrust" screen land set zone "V1-Untrust" screen tear-drop set zone "V1-Untrust" screen syn-flood set zone "V1-Untrust" screen ping-death set zone "V1-Untrust" screen ip-filter-src set zone "V1-Untrust" screen land set interface ethernet0/0 phy full 100mb set interface ethernet0/3 phy full 100mb set interface ethernet0/4 phy full 100mb set interface ethernet0/5 phy full 100mb set interface ethernet0/6 phy full 100mb set interface "ethernet0/0" zone "Untrust" set interface "ethernet0/1" zone "Null" set interface "bgroup0" zone "Trust" set interface "bgroup1" zone "Trust" set interface "bgroup2" zone "Trust" set interface bgroup2 port ethernet0/2 set interface bgroup0 port ethernet0/3 set interface bgroup0 port ethernet0/4 set interface bgroup1 port ethernet0/5 set interface bgroup1 port ethernet0/6 unset interface vlan1 ip set interface ethernet0/0 ip 215.173.182.18/29 set interface ethernet0/0 route set interface bgroup0 ip 192.168.1.1/24 set interface bgroup0 nat set interface bgroup1 ip 192.168.2.1/24 set interface bgroup1 nat set interface bgroup2 ip 192.168.3.1/24 set interface bgroup2 nat set interface ethernet0/0 gateway 215.173.182.17 unset interface vlan1 bypass-others-ipsec unset interface vlan1 bypass-non-ip set interface ethernet0/0 ip manageable set interface bgroup0 ip manageable set interface bgroup1 ip manageable set interface bgroup2 ip manageable set interface bgroup0 manage mtrace unset interface bgroup1 manage ssh unset interface bgroup1 manage telnet unset interface bgroup1 manage snmp unset interface bgroup1 manage ssl unset interface bgroup1 manage web unset interface bgroup2 manage ssh unset interface bgroup2 manage telnet unset interface bgroup2 manage snmp unset interface bgroup2 manage ssl unset interface bgroup2 manage web set interface ethernet0/0 vip 215.173.182.19 2048 "PPTP-VPN" 192.168.1.131 set interface ethernet0/0 vip 215.173.182.19 + 4280 "CrashPlan Server" 192.168.1.131 set interface ethernet0/0 vip 215.173.182.19 + 4282 "CrashPlan Console" 192.168.1.131 set interface ethernet0/0 vip 215.173.182.22 22 "MyVOIP_TCP22" 192.168.2.127 set interface ethernet0/0 vip 215.173.182.22 + 4569 "MyVOIP_UDP4569" 192.168.2.127 set interface ethernet0/0 vip 215.173.182.22 + 3389 "MyRDP" 192.168.2.202 set interface ethernet0/0 vip 215.173.182.22 + 873 "MyRsync" 192.168.2.201 set interface ethernet0/0 vip 215.173.182.22 + 80 "HTTP" 192.168.2.202 set interface ethernet0/0 vip 215.173.182.22 + 2048 "PPTP-VPN" 192.168.2.201 set interface ethernet0/0 vip 215.173.182.22 + 8080 "NZ_FMS_8080" 192.168.2.216 set interface ethernet0/0 vip 215.173.182.22 + 1935 "NZ_FMS_1935" 192.168.2.216 set interface bgroup0 dhcp server service set interface bgroup1 dhcp server service set interface bgroup2 dhcp server service set interface bgroup0 dhcp server auto set interface bgroup1 dhcp server auto set interface bgroup2 dhcp server auto set interface bgroup0 dhcp server option domainname companyalan set interface bgroup0 dhcp server option dns1 192.168.1.131 set interface bgroup1 dhcp server option domainname companyblan set interface bgroup1 dhcp server option dns1 192.168.2.202 set interface bgroup2 dhcp server option dns1 8.8.8.8 set interface bgroup2 dhcp server option wins1 8.8.4.4 set interface bgroup0 dhcp server ip 192.168.1.2 to 192.168.1.116 set interface bgroup1 dhcp server ip 192.168.2.2 to 192.168.2.116 set interface bgroup2 dhcp server ip 192.168.3.2 to 192.168.3.126 unset interface bgroup0 dhcp server config next-server-ip unset interface bgroup1 dhcp server config next-server-ip unset interface bgroup2 dhcp server config next-server-ip set interface "ethernet0/0" mip 215.173.182.21 host 192.168.2.202 netmask 255.255.255.255 vr "trust-vr" set interface "serial0/0" modem settings "USR" init "AT&F" set interface "serial0/0" modem settings "USR" active set interface "serial0/0" modem speed 115200 set interface "serial0/0" modem retry 3 set interface "serial0/0" modem interval 10 set interface "serial0/0" modem idle-time 10 set flow tcp-mss unset flow tcp-syn-check unset flow tcp-syn-bit-check set flow reverse-route clear-text prefer set flow reverse-route tunnel always set pki authority default scep mode "auto" set pki x509 default cert-path partial set pki x509 dn name "[email protected]" set dns host dns1 0.0.0.0 set dns host dns2 0.0.0.0 set dns host dns3 0.0.0.0 set address "Trust" "192.168.1.0/24" 192.168.1.0 255.255.255.0 set address "Trust" "192.168.2.0/24" 192.168.2.0 255.255.255.0 set address "Trust" "192.168.3.0/24" 192.168.3.0 255.255.255.0 set crypto-policy exit set ike respond-bad-spi 1 set ike ikev2 ike-sa-soft-lifetime 60 unset ike ikeid-enumeration unset ike dos-protection unset ipsec access-session enable set ipsec access-session maximum 5000 set ipsec access-session upper-threshold 0 set ipsec access-session lower-threshold 0 set ipsec access-session dead-p2-sa-timeout 0 unset ipsec access-session log-error unset ipsec access-session info-exch-connected unset ipsec access-session use-error-log set vrouter "untrust-vr" exit set vrouter "trust-vr" exit set l2tp default ppp-auth chap set url protocol websense exit set policy id 1 from "Trust" to "Untrust" "Any" "Any" "ANY" permit set policy id 1 exit set policy id 2 from "Untrust" to "Trust" "Any" "VIP(215.173.182.19)" "PPTP-VPN" permit traffic set policy id 2 exit set policy id 3 from "Untrust" to "Trust" "Any" "VIP(215.173.182.22)" "HTTP" permit log set policy id 3 set service "MyRDP" set service "MyRsync" set service "MyVOIP_TCP22" set service "MyVOIP_UDP4569" exit set policy id 6 from "Trust" to "Trust" "192.168.1.0/24" "192.168.2.0/24" "ANY" deny set policy id 6 exit set policy id 7 from "Trust" to "Trust" "192.168.2.0/24" "192.168.1.0/24" "ANY" deny set policy id 7 exit set policy id 8 from "Trust" to "Trust" "192.168.3.0/24" "192.168.1.0/24" "ANY" deny set policy id 8 exit set policy id 9 from "Trust" to "Trust" "192.168.3.0/24" "192.168.2.0/24" "ANY" deny set policy id 9 exit set policy id 10 from "Untrust" to "Trust" "Any" "MIP(215.173.182.21)" "NZ_FTP" permit set policy id 10 exit set policy id 11 from "Untrust" to "Trust" "Any" "VIP(215.173.182.22)" "PPTP-VPN" permit set policy id 11 exit set policy id 12 from "Untrust" to "Trust" "Any" "VIP(215.173.182.22)" "NZ_FMS_1935" permit set policy id 12 set service "NZ_FMS_8080" exit set policy id 13 from "Untrust" to "Trust" "Any" "VIP(215.173.182.19)" "CrashPlan Console" permit set policy id 13 set service "CrashPlan Server" exit set nsmgmt bulkcli reboot-timeout 60 set ssh version v2 set config lock timeout 5 unset license-key auto-update set telnet client enable set snmp port listen 161 set snmp port trap 162 set vrouter "untrust-vr" exit set vrouter "trust-vr" unset add-default-route exit set vrouter "untrust-vr" exit set vrouter "trust-vr" exit Note that I've previously posted a similar question (pertaining to the same device & replacement, but ultimately caused by a malfunctioning switch, and thus clouding the current issue): Outbound traffic being blocked for MIP/VIPped servers (Juniper SSG5)

  Read the article

• Installing Oracle 11gR2 on RHEL 6.2

  - by Chris

  Hello all I'm having some difficulty installing Oracle 11gR2 on RHEL 6.2 I have compiled a giant list of every single step I have taken so far I installed RHEL 6.2 on VMWARE it did it's easy install automatically I Selected 4gb of memory Selected max size of 80Gb Selected 2 processors Sorry for the bad styling copy paste isn't working correctly The version of oracle i downloaded is Linux x86-64 11.2.0.1 I am installing this on a local machine NOT a remote machine I followed the following documentation http://docs.oracle.com/cd/E11882_01/install.112/e24326/toc.htm I bolded the steps which I was least sure about from my research Easy installed with RHEL 6.2 for VMWARE Registered with red hat so I can get updates Reinstalled vmware-tools by pressing enter at every choice Sudo yum update at the end something about GPG key selected y then y Checked Memory Requirements grep MemTotal /proc/meminfo MemTotal: 3921368 kb uname -m x86_64 grep SwapTotal /proc/meminfo SwapTotal: 6160376 kb free total used free shared buffers cached Mem: 3921368 2032012 1889356 0 76216 1533268 -/+ buffers/cache: 422528 3498840 Swap: 6160376 0 6160376 df -h /dev/shm Filesystem Size Used Avail Use% Mounted on tmpfs 1.9G 276K 1.9G 1% /dev/shm df -h /tmp Filesystem Size Used Avail Use% Mounted on /dev/sda2 73G 2.7G 67G 4% / df -h Filesystem Size Used Avail Use% Mounted on /dev/sda2 73G 2.7G 67G 4% / tmpfs 1.9G 276K 1.9G 1% /dev/shm /dev/sda1 291M 58M 219M 21% /boot All looked fine to me except maybe for swap? Software Requirements cat /proc/version Linux version 2.6.32-220.el6.x86_64 ([email protected]) (gcc version 4.4.5 20110214 (Red Hat 4.4.5-6) (GCC) ) #1 SMP Wed Nov 9 08:03:13 EST 2011 uname -r 2.6.32-220.el6.x86_64 (same as above but whatever) According to the tutorial should be On Red Hat Enterprise Linux 6 2.6.32-71.el6.x86_64 or later These are the versions of software I have installed binutils-2.20.51.0.2-5.28.el6.x86_64 compat-libcap1-1.10-1.x86_64 compat-libstdc++-33-3.2.3-69.el6.x86_64 compat-libstdc++-33.i686 0:3.2.3-69.el6 gcc-4.4.6-3.el6.x86_64 gcc-c++.x86_64 0:4.4.6-3.el6 glibc-2.12-1.47.el6_2.12.x86_64 glibc-2.12-1.47.el6_2.12.i686 glibc-devel-2.12-1.47.el6_2.12.x86_64 glibc-devel.i686 0:2.12-1.47.el6_2.12 ksh.x86_64 0:20100621-12.el6_2.1 libgcc-4.4.6-3.el6.x86_64 libgcc-4.4.6-3.el6.i686 libstdc++-4.4.6-3.el6.x86_64 libstdc++.i686 0:4.4.6-3.el6 libstdc++-devel.i686 0:4.4.6-3.el6 libstdc++-devel-4.4.6-3.el6.x86_64 libaio-0.3.107-10.el6.x86_64 libaio-0.3.107-10.el6.i686 libaio-devel-0.3.107-10.el6.x86_64 libaio-devel-0.3.107-10.el6.i686 make-3.81-19.el6.x86_64 sysstat-9.0.4-18.el6.x86_64 unixODBC-2.2.14-11.el6.x86_64 unixODBC-devel-2.2.14-11.el6.x86_64 unixODBC-devel-2.2.14-11.el6.i686 unixODBC-2.2.14-11.el6.i686 8. Probably screwed up here or step 9 /usr/sbin/groupadd oinstall /usr/sbin/groupadd dba(not sure why this isn't in the tutorial) /usr/sbin/useradd -g oinstall -G dba oracle passwd oracle /sbin/sysctl -a | grep sem Xkernel.sem = 250 32000 32 128 /sbin/sysctl -a | grep shm kernel.shmmax = 68719476736 kernel.shmall = 4294967296 kernel.shmmni = 4096 vm.hugetlb_shm_group = 0 /sbin/sysctl -a | grep file-max Xfs.file-max = 384629 /sbin/sysctl -a | grep ip_local_port_range Xnet.ipv4.ip_local_port_range = 32768 61000 /sbin/sysctl -a | grep rmem_default Xnet.core.rmem_default = 124928 /sbin/sysctl -a | grep rmem_max Xnet.core.rmem_max = 131071 /sbin/sysctl -a | grep wmem_max Xnet.core.wmem_max = 131071 /sbin/sysctl -a | grep wmem_default Xnet.core.wmem_default = 124928 Here is my sysctl.conf file I only added the items that were bigger: Kernel sysctl configuration file for Red Hat Linux # For binary values, 0 is disabled, 1 is enabled. See sysctl(8) and sysctl.conf(5) for more details. Controls IP packet forwarding net.ipv4.ip_forward = 0 Controls source route verification net.ipv4.conf.default.rp_filter = 1 Do not accept source routing net.ipv4.conf.default.accept_source_route = 0 Controls the System Request debugging functionality of the kernel kernel.sysrq = 0 Controls whether core dumps will append the PID to the core filename. Useful for debugging multi-threaded applications. kernel.core_uses_pid = 1 Controls the use of TCP syncookies net.ipv4.tcp_syncookies = 1 Disable netfilter on bridges. net.bridge.bridge-nf-call-ip6tables = 0 net.bridge.bridge-nf-call-iptables = 0 net.bridge.bridge-nf-call-arptables = 0 Controls the maximum size of a message, in bytes kernel.msgmnb = 65536 Controls the default maxmimum size of a mesage queue kernel.msgmax = 65536 Controls the maximum shared segment size, in bytes kernel.shmmax = 68719476736 Controls the maximum number of shared memory segments, in pages kernel.shmall = 4294967296 fs.aio-max-nr = 1048576 fs.file-max = 6815744 kernel.sem = 250 32000 100 128 net.ipv4.ip_local_port_range = 9000 65500 net.core.rmem_default = 262144 net.core.rmem_max = 4194304 net.core.wmem_default = 262144 net.core.wmem_max = 1048576 /sbin/sysctl -p net.ipv4.ip_forward = 0 net.ipv4.conf.default.rp_filter = 1 net.ipv4.conf.default.accept_source_route = 0 kernel.sysrq = 0 kernel.core_uses_pid = 1 net.ipv4.tcp_syncookies = 1 error: "net.bridge.bridge-nf-call-ip6tables" is an unknown key error: "net.bridge.bridge-nf-call-iptables" is an unknown key error: "net.bridge.bridge-nf-call-arptables" is an unknown key kernel.msgmnb = 65536 kernel.msgmax = 65536 kernel.shmmax = 68719476736 kernel.shmall = 4294967296 fs.aio-max-nr = 1048576 fs.file-max = 6815744 kernel.sem = 250 32000 100 128 net.ipv4.ip_local_port_range = 9000 65500 net.core.rmem_default = 262144 net.core.rmem_max = 4194304 net.core.wmem_default = 262144 net.core.wmem_max = 1048576 su - oracle ulimit -Sn 1024 ulimit -Hn 1024 ulimit -Su 1024 ulimit -Hu 30482 ulimit -Su 1024 ulimit -Ss 10240 ulimit -Hs unlimited su - nano /etc/security/limits.conf *added to the end of the file * oracle soft nproc 2047 oracle hard nproc 16384 oracle soft nofile 1024 oracle hard nofile 65536 oracle soft stack 10240 exit exit su - mkdir -p /app/ chown -R oracle:oinstall /app/ chmod -R 775 /app/ 9. THIS IS PROBABLY WHERE I MESSED UP I then exited out of the root account so now I'm back in my account chris then I su - oracle echo $SHELL /bin/bash umask 0022 (so it should be set already to what is neccesary) Also from what I have read I do not need to set the DISPLAY variable because I'm installing this on the localhost I then opened the .bash_profile of the oracle and changed it to the following .bash_profile Get the aliases and functions if [ -f ~/.bashrc ]; then . ~/.bashrc fi User specific environment and startup programs PATH=$PATH:$HOME/bin; export PATH ORACLE_BASE=/app/oracle ORACLE_SID=orcl export ORACLE_BASE ORACLE_SID I then shutdown the virtual machine shared my desktop folder from my windows 7 then turned back on the virtual machine logged in as chris opened up a terminal then: su - for some reason the shared folder didn't appear so I reinstalled vmware tools again and restarted then same as before su - cp -R linux_oracle/database /db; chown -R oracle:oinstall /db; chmod -R 775 /db; ll /db drwxrwxr-x. 8 oracle oinstall 4096 Jun 5 06:20 database exit su - oracle cd /db/database ./runInstaller AND FINALLY THE INFAMOUS JAVA:132 ERROR MESSAGE Starting Oracle Universal Installer... Checking Temp space: must be greater than 80 MB. Actual 65646 MB Passed Checking swap space: must be greater than 150 MB. Actual 6015 MB Passed Checking monitor: must be configured to display at least 256 colors. Actual 16777216 Passed Preparing to launch Oracle Universal Installer from /tmp/OraInstall2012-06-05_06-47-12AM. Please wait ...[oracle@localhost database]$ Exception in thread "main" java.lang.UnsatisfiedLinkError: /tmp/OraInstall2012-06-05_06-47-12AM/jdk/jre/lib/i386/xawt/libmawt.so: libXext.so.6: cannot open shared object file: No such file or directory at java.lang.ClassLoader$NativeLibrary.load(Native Method) at java.lang.ClassLoader.loadLibrary0(ClassLoader.java:1751) at java.lang.ClassLoader.loadLibrary(ClassLoader.java:1647) at java.lang.Runtime.load0(Runtime.java:769) at java.lang.System.load(System.java:968) at java.lang.ClassLoader$NativeLibrary.load(Native Method) at java.lang.ClassLoader.loadLibrary0(ClassLoader.java:1751) at java.lang.ClassLoader.loadLibrary(ClassLoader.java:1668) at java.lang.Runtime.loadLibrary0(Runtime.java:822) at java.lang.System.loadLibrary(System.java:993) at sun.security.action.LoadLibraryAction.run(LoadLibraryAction.java:50) at java.security.AccessController.doPrivileged(Native Method) at java.awt.Toolkit.loadLibraries(Toolkit.java:1509) at java.awt.Toolkit.(Toolkit.java:1530) at com.jgoodies.looks.LookUtils.isLowResolution(Unknown Source) at com.jgoodies.looks.LookUtils.(Unknown Source) at com.jgoodies.looks.plastic.PlasticLookAndFeel.(PlasticLookAndFeel.java:122) at java.lang.Class.forName0(Native Method) at java.lang.Class.forName(Class.java:242) at javax.swing.SwingUtilities.loadSystemClass(SwingUtilities.java:1783) at javax.swing.UIManager.setLookAndFeel(UIManager.java:480) at oracle.install.commons.util.Application.startup(Application.java:758) at oracle.install.commons.flow.FlowApplication.startup(FlowApplication.java:164) at oracle.install.commons.flow.FlowApplication.startup(FlowApplication.java:181) at oracle.install.commons.base.driver.common.Installer.startup(Installer.java:265) at oracle.install.ivw.db.driver.DBInstaller.startup(DBInstaller.java:114) at oracle.install.ivw.db.driver.DBInstaller.main(DBInstaller.java:132)

  Read the article

• mdadm raid5 recover double disk failure - with a twist (drive order)

  - by Peter Bos

  Let me acknowledge first off that I have made mistakes, and that I have a backup for most but not all of the data on this RAID. I still have hope of recovering the rest of the data. I don't have the kind of money to take the drives to a recovery expert company. Mistake #0, not having a 100% backup. I know. I have a mdadm RAID5 system of 4x3TB. Drives /dev/sd[b-e], all with one partition /dev/sd[b-e]1. I'm aware that RAID5 on very large drives is risky, yet I did it anyway. Recent events The RAID become degraded after a two drive failure. One drive [/dev/sdc] is really gone, the other [/dev/sde] came back up after a power cycle, but was not automatically re-added to the RAID. So I was left with a 4 device RAID with only 2 active drives [/dev/sdb and /dev/sdd]. Mistake #1, not using dd copies of the drives for restoring the RAID. I did not have the drives or the time. Mistake #2, not making a backup of the superblock and mdadm -E of the remaining drives. Recovery attempt I reassembled the RAID in degraded mode with mdadm --assemble --force /dev/md0, using /dev/sd[bde]1. I could then access my data. I replaced /dev/sdc with a spare; empty; identical drive. I removed the old /dev/sdc1 from the RAID mdadm --fail /dev/md0 /dev/sdc1 Mistake #3, not doing this before replacing the drive I then partitioned the new /dev/sdc and added it to the RAID. mdadm --add /dev/md0 /dev/sdc1 It then began to restore the RAID. ETA 300 mins. I followed the process via /proc/mdstat to 2% and then went to do other stuff. Checking the result Several hours (but less then 300 mins) later, I checked the process. It had stopped due to a read error on /dev/sde1. Here is where the trouble really starts I then removed /dev/sde1 from the RAID and re-added it. I can't remember why I did this; it was late. mdadm --manage /dev/md0 --remove /dev/sde1 mdadm --manage /dev/md0 --add /dev/sde1 However, /dev/sde1 was now marked as spare. So I decided to recreate the whole array using --assume-clean using what I thought was the right order, and with /dev/sdc1 missing. mdadm --create /dev/md0 --assume-clean -l5 -n4 /dev/sdb1 missing /dev/sdd1 /dev/sde1 That worked, but the filesystem was not recognized while trying to mount. (It should have been EXT4). Device order I then checked a recent backup I had of /proc/mdstat, and I found the drive order. md0 : active raid5 sdb1[0] sde1[4] sdd1[2] sdc1[1] 8790402048 blocks super 1.2 level 5, 512k chunk, algorithm 2 [4/4] [UUUU] I then remembered this RAID had suffered a drive loss about a year ago, and recovered from it by replacing the faulty drive with a spare one. That may have scrambled the device order a bit...so there was no drive [3] but only [0],[1],[2], and [4]. I tried to find the drive order with the Permute_array script: https://raid.wiki.kernel.org/index.php/Permute_array.pl but that did not find the right order. Questions I now have two main questions: I screwed up all the superblocks on the drives, but only gave: mdadm --create --assume-clean commands (so I should not have overwritten the data itself on /dev/sd[bde]1. Am I right that in theory the RAID can be restored [assuming for a moment that /dev/sde1 is ok] if I just find the right device order? Is it important that /dev/sde1 be given the device number [4] in the RAID? When I create it with mdadm --create /dev/md0 --assume-clean -l5 -n4 \ /dev/sdb1 missing /dev/sdd1 /dev/sde1 it is assigned the number [3]. I wonder if that is relevant to the calculation of the parity blocks. If it turns out to be important, how can I recreate the array with /dev/sdb1[0] missing[1] /dev/sdd1[2] /dev/sde1[4]? If I could get that to work I could start it in degraded mode and add the new drive /dev/sdc1 and let it resync again. It's OK if you would like to point out to me that this may not have been the best course of action, but you'll find that I realized this. It would be great if anyone has any suggestions.

  Read the article

• rm on a directory with millions of files

  - by BMDan

  Background: physical server, about two years old, 7200-RPM SATA drives connected to a 3Ware RAID card, ext3 FS mounted noatime and data=ordered, not under crazy load, kernel 2.6.18-92.1.22.el5, uptime 545 days. Directory doesn't contain any subdirectories, just millions of small (~100 byte) files, with some larger (a few KB) ones. We have a server that has gone a bit cuckoo over the course of the last few months, but we only noticed it the other day when it started being unable to write to a directory due to it containing too many files. Specifically, it started throwing this error in /var/log/messages: ext3_dx_add_entry: Directory index full! The disk in question has plenty of inodes remaining: Filesystem Inodes IUsed IFree IUse% Mounted on /dev/sda3 60719104 3465660 57253444 6% / So I'm guessing that means we hit the limit of how many entries can be in the directory file itself. No idea how many files that would be, but it can't be more, as you can see, than three million or so. Not that that's good, mind you! But that's part one of my question: exactly what is that upper limit? Is it tunable? Before I get yelled at--I want to tune it down; this enormous directory caused all sorts of issues. Anyway, we tracked down the issue in the code that was generating all of those files, and we've corrected it. Now I'm stuck with deleting the directory. A few options here: rm -rf (dir)I tried this first. I gave up and killed it after it had run for a day and a half without any discernible impact. unlink(2) on the directory: Definitely worth consideration, but the question is whether it'd be faster to delete the files inside the directory via fsck than to delete via unlink(2). That is, one way or another, I've got to mark those inodes as unused. This assumes, of course, that I can tell fsck not to drop entries to the files in /lost+found; otherwise, I've just moved my problem. In addition to all the other concerns, after reading about this a bit more, it turns out I'd probably have to call some internal FS functions, as none of the unlink(2) variants I can find would allow me to just blithely delete a directory with entries in it. Pooh. while [ true ]; do ls -Uf | head -n 10000 | xargs rm -f 2/dev/null; done ) This is actually the shortened version; the real one I'm running, which just adds some progress-reporting and a clean stop when we run out of files to delete, is: export i=0; time ( while [ true ]; do ls -Uf | head -n 3 | grep -qF '.png' || break; ls -Uf | head -n 10000 | xargs rm -f 2/dev/null; export i=$(($i+10000)); echo "$i..."; done ) This seems to be working rather well. As I write this, it's deleted 260,000 files in the past thirty minutes or so. Now, for the questions: As mentioned above, is the per-directory entry limit tunable? Why did it take "real 7m9.561s / user 0m0.001s / sys 0m0.001s" to delete a single file which was the first one in the list returned by "ls -U", and it took perhaps ten minutes to delete the first 10,000 entries with the command in #3, but now it's hauling along quite happily? For that matter, it deleted 260,000 in about thirty minutes, but it's now taken another fifteen minutes to delete 60,000 more. Why the huge swings in speed? Is there a better way to do this sort of thing? Not store millions of files in a directory; I know that's silly, and it wouldn't have happened on my watch. Googling the problem and looking through SF and SO offers a lot of variations on "find" that obviously have the wrong idea; it's not going to be faster than my approach for several self-evident reasons. But does the delete-via-fsck idea have any legs? Or something else entirely? I'm eager to hear out-of-the-box (or inside-the-not-well-known-box) thinking. Thanks for reading the small novel; feel free to ask questions and I'll be sure to respond. I'll also update the question with the final number of files and how long the delete script ran once I have that. Final script output!: 2970000... 2980000... 2990000... 3000000... 3010000... real 253m59.331s user 0m6.061s sys 5m4.019s So, three million files deleted in a bit over four hours.

  Read the article

• How to install MariaDB rpms in CentOS 6.4 using rpm (not yum cmd) + handling mysql-libs conflicts

  - by Pat C

  I need to script the install of MariaDB using the rpm command in CentOS 6.4. I can't use yum since it's going to be an offline install so there's no access to the repository. The only MySQL package installed is mysql-libs as various other packages in CentOS depend on it. When I did a test install of MariaDB with yum it correctly accounted for mysql-libs and uninstalled it at the end as MariaDB could handle the dependencies after it was installed: [root@new-host-6 ~]# yum install MariaDB-client MariaDB-common MariaDB-compat MariaDB-devel MariaDB-server MariaDB-shared Loaded plugins: downloadonly, fastestmirror, refresh-packagekit, security, verify Loading mirror speeds from cached hostfile * base: mirrors.kernel.org * extras: mirror.keystealth.org * updates: mirror.umd.edu Setting up Install Process Resolving Dependencies --> Running transaction check ---> Package MariaDB-client.x86_64 0:5.5.32-1 will be installed ---> Package MariaDB-common.x86_64 0:5.5.32-1 will be installed ---> Package MariaDB-compat.x86_64 0:5.5.32-1 will be obsoleting ---> Package MariaDB-devel.x86_64 0:5.5.32-1 will be installed ---> Package MariaDB-server.x86_64 0:5.5.32-1 will be installed ---> Package MariaDB-shared.x86_64 0:5.5.32-1 will be obsoleting ---> Package mysql-libs.x86_64 0:5.1.66-2.el6_3 will be obsoleted --> Finished Dependency Resolution Dependencies Resolved ==================================================================================================================================================================== Package Arch Version Repository Size ==================================================================================================================================================================== Installing: MariaDB-client x86_64 5.5.32-1 mariadb 10 M MariaDB-common x86_64 5.5.32-1 mariadb 23 k MariaDB-compat x86_64 5.5.32-1 mariadb 2.7 M replacing mysql-libs.x86_64 5.1.66-2.el6_3 MariaDB-devel x86_64 5.5.32-1 mariadb 5.6 M MariaDB-server x86_64 5.5.32-1 mariadb 34 M MariaDB-shared x86_64 5.5.32-1 mariadb 1.1 M replacing mysql-libs.x86_64 5.1.66-2.el6_3 Transaction Summary ==================================================================================================================================================================== Install 6 Package(s) Total download size: 53 M Is this ok [y/N]: y Downloading Packages: (1/6): MariaDB-5.5.32-centos6-x86_64-client.rpm | 10 MB 00:06 (2/6): MariaDB-5.5.32-centos6-x86_64-common.rpm | 23 kB 00:00 (3/6): MariaDB-5.5.32-centos6-x86_64-compat.rpm | 2.7 MB 00:02 (4/6): MariaDB-5.5.32-centos6-x86_64-devel.rpm | 5.6 MB 00:06 (5/6): MariaDB-5.5.32-centos6-x86_64-server.rpm | 34 MB 00:23 (6/6): MariaDB-5.5.32-centos6-x86_64-shared.rpm | 1.1 MB 00:00 -------------------------------------------------------------------------------------------------------------------------------------------------------------------- Total 1.3 MB/s | 53 MB 00:40 warning: rpmts_HdrFromFdno: Header V4 DSA/SHA1 Signature, key ID 1bb943db: NOKEY Retrieving key from https://yum.mariadb.org/RPM-GPG-KEY-MariaDB Importing GPG key 0x1BB943DB: Userid: "Daniel Bartholomew (Monty Program signing key) <[email protected]>" From : https://yum.mariadb.org/RPM-GPG-KEY-MariaDB Is this ok [y/N]: y Running rpm_check_debug Running Transaction Test Transaction Test Succeeded Running Transaction Warning: RPMDB altered outside of yum. Installing : MariaDB-compat-5.5.32-1.x86_64 1/7 Installing : MariaDB-common-5.5.32-1.x86_64 2/7 Installing : MariaDB-server-5.5.32-1.x86_64 3/7 chown: cannot access `/var/lib/mysql': No such file or directory PLEASE REMEMBER TO SET A PASSWORD FOR THE MariaDB root USER ! To do so, start the server, then issue the following commands: '/usr/bin/mysqladmin' -u root password 'new-password' '/usr/bin/mysqladmin' -u root -h new-host-6 password 'new-password' Alternatively you can run: '/usr/bin/mysql_secure_installation' which will also give you the option of removing the test databases and anonymous user created by default. This is strongly recommended for production servers. See the MariaDB Knowledgebase at http://kb.askmonty.org or the MySQL manual for more instructions. Please report any problems with the '/usr/bin/mysqlbug' script! The latest information about MariaDB is available at http://mariadb.org/. You can find additional information about the MySQL part at: http://dev.mysql.com Support MariaDB development by buying support/new features from Monty Program Ab. You can contact us about this at [email protected]. Alternatively consider joining our community based development effort: http://kb.askmonty.org/en/contributing-to-the-mariadb-project/ Installing : MariaDB-devel-5.5.32-1.x86_64 4/7 Installing : MariaDB-client-5.5.32-1.x86_64 5/7 Installing : MariaDB-shared-5.5.32-1.x86_64 6/7 Erasing : mysql-libs-5.1.66-2.el6_3.x86_64 7/7 Verifying : MariaDB-common-5.5.32-1.x86_64 1/7 Verifying : MariaDB-server-5.5.32-1.x86_64 2/7 Verifying : MariaDB-devel-5.5.32-1.x86_64 3/7 Verifying : MariaDB-client-5.5.32-1.x86_64 4/7 Verifying : MariaDB-compat-5.5.32-1.x86_64 5/7 Verifying : MariaDB-shared-5.5.32-1.x86_64 6/7 Verifying : mysql-libs-5.1.66-2.el6_3.x86_64 7/7 Installed: MariaDB-client.x86_64 0:5.5.32-1 MariaDB-common.x86_64 0:5.5.32-1 MariaDB-compat.x86_64 0:5.5.32-1 MariaDB-devel.x86_64 0:5.5.32-1 MariaDB-server.x86_64 0:5.5.32-1 MariaDB-shared.x86_64 0:5.5.32-1 Replaced: mysql-libs.x86_64 0:5.1.66-2.el6_3 Complete! My question is, what is the equivalent way to install the MariaDB packages using the rpm command only as opposed to yum? If I do rpm -ivh MariaDB*.rpm, I will get a ton of messages like the following about conflicts with mysql-libs: file /etc/my.cnf from install of MariaDB-common-5.5.32-1.x86_64 conflicts with file from package mysql-libs-5.1.66-2.el6_3.x86_64 file /usr/share/mysql/charsets/Index.xml from install of MariaDB-common-5.5.32-1.x86_64 conflicts with file from package mysql-libs-5.1.66-2.el6_3.x86_64 I then used the --force option to install the MariaDB rpms and uninstalled mysql-lib, I didn't get any weird messages but I'm not sure that is the cleanest method to handle the conflicts and do the install. So can someone confirm that installing MariaDB with the following rpm commands would be the same as using yum to install the packages and handle mysql-libs conflicts/removal: rpm -ivh --force MariaDB*.rpm rpm -e mysql-libs Thanks for any input!

  Read the article

• KVM Guest installed from console. But how to get to the guest's console?

  - by badbishop

  I'm trying to install a fully virtualized guest (Fedora 14 x86_64) on KVM (RHEL 6), using command-line only (both hypervisor and guest). It goes without errors, and without a tangible result . I'd like to know how to do a text-only installation. So, here's what I've done: # virt-install \ --name=FE --ram=756 --vcpus=1 \ --file=/var/lib/libvirt/images/FE.img --network bridge:br0 \ --nographics --os-type=linux \ --extra-args='console=tty0' -v \ --cdrom=/media/usb/Fedora-14-x86_64-Live-Desktop.iso Starting install... Creating domain... | 0 B 00:00 Connected to domain FE Escape character is ^] ÿ Now what? As I understand after googling for a couple of days, I should see the guest's output from the text installation, but nothing happens. virt-viewer cannot connect to it, kindly suggesting that I explore all the options by adding --help (which I did). If I reconnect with virsh, I see this: Domain installation still in progress. You can reconnect to the console to complete the installation process. [root@v ~] # virsh console FEConnected to domain FE Escape character is ^] This shows that VM is running # virsh list Id Name State ---------------------------------- 8 FE running Qemu log: LC_ALL=C PATH=/sbin:/usr/sbin:/bin:/usr/bin /usr/libexec/qemu-kvm -S -M rhel6.0.0 -enable-kvm -m 756 -smp 1,sockets=1,cores=1,threads=1 -name FE -uuid 6989d008-7c89-424c-d2d3-f41235c57a18 -nographic -nodefconfig -nodefaults -chardev socket,id=monitor,path=/var/lib/libvirt/qemu/FE.monitor,server,nowait -mon chardev=monitor,mode=control -rtc base=utc -no-reboot -boot d -drive file=/var/lib/libvirt/images/FE.img,if=none,id=drive-ide0-0-0,format=raw,cache=none -device ide-drive,bus=ide.0,unit=0,drive=drive-ide0-0-0,id=ide0-0-0 -drive file=/media/usb/Fedora-14-x86_64-Live-Desktop.iso,if=none,media=cdrom,id=drive-ide0-1-0,readonly=on,format=raw -device ide-drive,bus=ide.1,unit=0,drive=drive-ide0-1-0,id=ide0-1-0 -netdev tap,fd=20,id=hostnet0 -device rtl8139,netdev=hostnet0,id=net0,mac=52:54:00:0a:65:8d,bus=pci.0,addr=0x2 -chardev pty,id=serial0 -device isa-serial,chardev=serial0 -usb -device virtio-balloon-pci,id=balloon0,bus=pci.0,addr=0x3 char device redirected to /dev/pts/1 Output of /etc/libvirt/qemu/FE.xml # cat /etc/libvirt/qemu/FE.xml <domain type='kvm'> <name>FE</name> <uuid>6989d008-7c89-424c-d2d3-f41235c57a18</uuid> <memory>774144</memory> <currentMemory>774144</currentMemory> <vcpu>1</vcpu> <os> <type arch='x86_64' machine='rhel6.0.0'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> <apic/> <pae/> </features> <clock offset='utc'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/libexec/qemu-kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='raw' cache='none'/> <source file='/var/lib/libvirt/images/FE.img'/> <target dev='hda' bus='ide'/> <address type='drive' controller='0' bus='0' unit='0'/> </disk> <disk type='block' device='cdrom'> <driver name='qemu' type='raw'/> <target dev='hdc' bus='ide'/> <readonly/> <address type='drive' controller='0' bus='1' unit='0'/> </disk> <controller type='ide' index='0'> <address type='pci' domain='0x0000' bus='0x00' slot='0x01' function='0x1'/> </controller> <interface type='bridge'> <mac address='52:54:00:0a:65:8d'/> <source bridge='br0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x0'/> </interface> <serial type='pty'> <target port='0'/> </serial> <console type='pty'> <target port='0'/> </console> <memballoon model='virtio'> <address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x0'/> </memballoon> </devices> </domain> I'm obviously missing something that many others don't, but what is it? Thanx in advance!

  Read the article

• How to diagnose failing 6Gbps SATA connection?

  - by whitequark

  I have a Samsung RC530 notebook and OCZ Vertex-3 6Gbps SATA SSD working in AHCI mode. # dmesg | grep DMI SAMSUNG ELECTRONICS CO., LTD. RC530/RC730/RC530/RC730, BIOS 03WD.M008.20110927.PSA 09/27/2011 # lspci -nn 00:1f.2 SATA controller [0106]: Intel Corporation 6 Series/C200 Series Chipset Family 6 port SATA AHCI Controller [8086:1c03] (rev 04) # sdparm -a /dev/sda /dev/sda: ATA OCZ-VERTEX3 2.15 At the boot, the following messages are present in dmesg (I am running Debian wheezy @ Linux 3.2.8): # dmesg | grep -iE '(ata|ahci)' [ 5.179783] ahci 0000:00:1f.2: version 3.0 [ 5.179802] ahci 0000:00:1f.2: PCI INT B -> GSI 19 (level, low) -> IRQ 19 [ 5.179864] ahci 0000:00:1f.2: irq 42 for MSI/MSI-X [ 5.195424] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 6 ports 6 Gbps 0x5 impl SATA mode [ 5.195429] ahci 0000:00:1f.2: flags: 64bit ncq sntf pm led clo pio slum part ems apst [ 5.195436] ahci 0000:00:1f.2: setting latency timer to 64 [ 5.204035] scsi0 : ahci [ 5.204301] scsi1 : ahci [ 5.204447] scsi2 : ahci [ 5.204592] scsi3 : ahci [ 5.204682] scsi4 : ahci [ 5.204799] scsi5 : ahci [ 5.204917] ata1: SATA max UDMA/133 abar m2048@0xf7c06000 port 0xf7c06100 irq 42 [ 5.204920] ata2: DUMMY [ 5.204923] ata3: SATA max UDMA/133 abar m2048@0xf7c06000 port 0xf7c06200 irq 42 [ 5.204924] ata4: DUMMY [ 5.204926] ata5: DUMMY [ 5.204927] ata6: DUMMY [ 5.523039] ata3: SATA link up 1.5 Gbps (SStatus 113 SControl 300) [ 5.525911] ata3.00: ATAPI: TSSTcorp CDDVDW SN-208BB, SC00, max UDMA/100 [ 5.531006] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 5.533703] ata3.00: configured for UDMA/100 [ 5.542790] ata1.00: ATA-8: OCZ-VERTEX3, 2.15, max UDMA/133 [ 5.542800] ata1.00: 117231408 sectors, multi 16: LBA48 NCQ (depth 31/32), AA [ 5.552751] ata1.00: configured for UDMA/133 [ 5.553050] scsi 0:0:0:0: Direct-Access ATA OCZ-VERTEX3 2.15 PQ: 0 ANSI: 5 [ 5.559621] scsi 2:0:0:0: CD-ROM TSSTcorp CDDVDW SN-208BB SC00 PQ: 0 ANSI: 5 [ 5.564059] sd 0:0:0:0: [sda] 117231408 512-byte logical blocks: (60.0 GB/55.8 GiB) [ 5.564127] sd 0:0:0:0: [sda] Write Protect is off [ 5.564131] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00 [ 5.564158] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA [ 5.564582] sda: sda1 [ 5.564810] sd 0:0:0:0: [sda] Attached SCSI disk [ 5.572006] sr0: scsi3-mmc drive: 16x/24x writer dvd-ram cd/rw xa/form2 cdda tray [ 5.572010] cdrom: Uniform CD-ROM driver Revision: 3.20 [ 5.572189] sr 2:0:0:0: Attached scsi CD-ROM sr0 [ 6.717181] ata1.00: exception Emask 0x50 SAct 0x1 SErr 0x280900 action 0x6 frozen [ 6.717238] ata1.00: irq_stat 0x08000000, interface fatal error [ 6.717291] ata1: SError: { UnrecovData HostInt 10B8B BadCRC } [ 6.717342] ata1.00: failed command: READ FPDMA QUEUED [ 6.717395] ata1.00: cmd 60/50:00:20:39:58/00:00:00:00:00/40 tag 0 ncq 40960 in [ 6.717396] res 40/00:00:20:39:58/00:00:00:00:00/40 Emask 0x50 (ATA bus error) [ 6.717503] ata1.00: status: { DRDY } [ 6.717553] ata1: hard resetting link [ 7.033417] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 7.055234] ata1.00: configured for UDMA/133 [ 7.055262] ata1: EH complete [ 7.147280] ata1.00: exception Emask 0x10 SAct 0xf8 SErr 0x280100 action 0x6 frozen [ 7.147340] ata1.00: irq_stat 0x08000000, interface fatal error [ 7.147393] ata1: SError: { UnrecovData 10B8B BadCRC } [ 7.147460] ata1.00: failed command: READ FPDMA QUEUED [ 7.147529] ata1.00: cmd 60/08:18:88:17:41/00:00:02:00:00/40 tag 3 ncq 4096 in [ 7.147531] res 40/00:38:50:99:64/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.147691] ata1.00: status: { DRDY } [ 7.147754] ata1.00: failed command: READ FPDMA QUEUED [ 7.147821] ata1.00: cmd 60/00:20:f8:42:4c/01:00:02:00:00/40 tag 4 ncq 131072 in [ 7.147822] res 40/00:38:50:99:64/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.147977] ata1.00: status: { DRDY } [ 7.148036] ata1.00: failed command: READ FPDMA QUEUED [ 7.148100] ata1.00: cmd 60/50:28:f8:43:4c/00:00:02:00:00/40 tag 5 ncq 40960 in [ 7.148101] res 40/00:38:50:99:64/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.148255] ata1.00: status: { DRDY } [ 7.148315] ata1.00: failed command: READ FPDMA QUEUED [ 7.148379] ata1.00: cmd 60/00:30:50:98:64/01:00:02:00:00/40 tag 6 ncq 131072 in [ 7.148380] res 40/00:38:50:99:64/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.148534] ata1.00: status: { DRDY } [ 7.148593] ata1.00: failed command: READ FPDMA QUEUED [ 7.148657] ata1.00: cmd 60/00:38:50:99:64/01:00:02:00:00/40 tag 7 ncq 131072 in [ 7.148658] res 40/00:38:50:99:64/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.148813] ata1.00: status: { DRDY } [ 7.148875] ata1: hard resetting link [ 7.464842] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 7.486794] ata1.00: configured for UDMA/133 [ 7.486822] ata1: EH complete [ 7.546395] ata1.00: exception Emask 0x10 SAct 0x2f SErr 0x280100 action 0x6 frozen [ 7.546470] ata1.00: irq_stat 0x08000000, interface fatal error [ 7.546531] ata1: SError: { UnrecovData 10B8B BadCRC } [ 7.546588] ata1.00: failed command: READ FPDMA QUEUED [ 7.546648] ata1.00: cmd 60/00:00:e0:4b:61/01:00:02:00:00/40 tag 0 ncq 131072 in [ 7.546649] res 40/00:28:e0:4c:61/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.546794] ata1.00: status: { DRDY } [ 7.546847] ata1.00: failed command: READ FPDMA QUEUED [ 7.546906] ata1.00: cmd 60/00:08:90:2f:48/01:00:02:00:00/40 tag 1 ncq 131072 in [ 7.546907] res 40/00:28:e0:4c:61/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.547053] ata1.00: status: { DRDY } [ 7.547106] ata1.00: failed command: READ FPDMA QUEUED [ 7.547165] ata1.00: cmd 60/00:10:90:30:48/01:00:02:00:00/40 tag 2 ncq 131072 in [ 7.547166] res 40/00:28:e0:4c:61/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.547310] ata1.00: status: { DRDY } [ 7.547363] ata1.00: failed command: READ FPDMA QUEUED [ 7.547422] ata1.00: cmd 60/00:18:50:c7:64/01:00:02:00:00/40 tag 3 ncq 131072 in [ 7.547423] res 40/00:28:e0:4c:61/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.547568] ata1.00: status: { DRDY } [ 7.547621] ata1.00: failed command: READ FPDMA QUEUED [ 7.547681] ata1.00: cmd 60/00:28:e0:4c:61/01:00:02:00:00/40 tag 5 ncq 131072 in [ 7.547682] res 40/00:28:e0:4c:61/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.547825] ata1.00: status: { DRDY } [ 7.547882] ata1: hard resetting link [ 7.864408] ata1: SATA link up 6.0 Gbps (SStatus 133 SControl 300) [ 7.886351] ata1.00: configured for UDMA/133 [ 7.886375] ata1: EH complete [ 7.890012] ata1: limiting SATA link speed to 3.0 Gbps [ 7.890016] ata1.00: exception Emask 0x10 SAct 0x7 SErr 0x280100 action 0x6 frozen [ 7.890093] ata1.00: irq_stat 0x08000000, interface fatal error [ 7.890152] ata1: SError: { UnrecovData 10B8B BadCRC } [ 7.890210] ata1.00: failed command: READ FPDMA QUEUED [ 7.890272] ata1.00: cmd 60/00:00:90:33:48/01:00:02:00:00/40 tag 0 ncq 131072 in [ 7.890273] res 40/00:10:e0:4f:61/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.890418] ata1.00: status: { DRDY } [ 7.890472] ata1.00: failed command: READ FPDMA QUEUED [ 7.890530] ata1.00: cmd 60/00:08:90:34:48/01:00:02:00:00/40 tag 1 ncq 131072 in [ 7.890531] res 40/00:10:e0:4f:61/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.890672] ata1.00: status: { DRDY } [ 7.890724] ata1.00: failed command: READ FPDMA QUEUED [ 7.890781] ata1.00: cmd 60/78:10:e0:4f:61/00:00:02:00:00/40 tag 2 ncq 61440 in [ 7.890782] res 40/00:10:e0:4f:61/00:00:02:00:00/40 Emask 0x10 (ATA bus error) [ 7.890925] ata1.00: status: { DRDY } [ 7.890981] ata1: hard resetting link [ 8.208021] ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 320) [ 8.230100] ata1.00: configured for UDMA/133 [ 8.230124] ata1: EH complete Looks like the SATA interface tries to use 6Gbps link, then fails miserably and Linux fallbacks to 3Gbps. This is somewhat fine for me, as the system boots successfully each time and works under high load (cd linux-3.2.8; make -j16). I've also ran memtest86+ and it did not find any errors. What concerns me more is that Grub sometimes takes a long time to load the images and/or fails to load itself completely. The error is consistent and is probablistic: that is, each time I boot I have a certain chance to fail. Actually, I have a slight suspiction on the cause of the failure. Look at the cabling: What kind of engineer does it this way? Nah. Even 1Gbps Ethernet hardly tolerates cables bent over a small angle, and there you have 6Gbps SATA. How cound I determine and fix the cause of errors and/or switch the link to 3Gbps mode permanently?

  Read the article

• KVM Virtual guest Paused on Reboot

  - by David Hamilton

  I'm running REHL 6 and just installed a Ubuntu Server Guest via KVM set to start at boot. This works correctly and the guest loads, but it loads "paused" and requires that I manually un-pause it. Can someone give me a hint as to how I can I get the Guest OS to actually become active on boot? Here is the libvert dump as requested...Also tried libvert auto-start --- no effect. <domain type='kvm' id='1'> <name>MailServer</name> <uuid>a61dae75-1f5c-d536-718f-3c615d9b4868</uuid> <memory>4194304</memory> <currentMemory>4194304</currentMemory> <vcpu>4</vcpu> <os> <type arch='x86_64' machine='rhel6.0.0'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> <apic/> <pae/> </features> <clock offset='utc'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/libexec/qemu-kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='raw' cache='none'/> <source file='/home/MailServer/MailServer-1.img'/> <target dev='hda' bus='ide'/> <alias name='ide0-0-0'/> <address type='drive' controller='0' bus='0' unit='0'/> </disk> <disk type='block' device='cdrom'> <driver name='qemu' type='raw'/> <target dev='hdc' bus='ide'/> <readonly/> <alias name='ide0-1-0'/> <address type='drive' controller='0' bus='1' unit='0'/> </disk> <controller type='ide' index='0'> <alias name='ide0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x01' function='0x1'/> </controller> <interface type='bridge'> <mac address='52:54:00:cd:f9:9f'/> <source bridge='br0'/> <target dev='vnet0'/> <model type='virtio'/> <alias name='net0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x0'/> </interface> <serial type='pty'> <source path='/dev/pts/1'/> <target port='0'/> <alias name='serial0'/> </serial> <console type='pty' tty='/dev/pts/1'> <source path='/dev/pts/1'/> <target port='0'/> <alias name='serial0'/> </console> <input type='mouse' bus='ps2'/> <graphics type='vnc' port='5900' autoport='yes'/> <sound model='ac97'> <alias name='sound0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x04' function='0x0'/> </sound> <video> <model type='cirrus' vram='9216' heads='1'/> <alias name='video0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x0'/> </video> <memballoon model='virtio'> <alias name='balloon0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x05' function='0x0'/> </memballoon> </devices> <seclabel type='dynamic' model='selinux'> <label>system_u:system_r:svirt_t:s0:c211,c271</label> <imagelabel>system_u:object_r:svirt_image_t:s0:c211,c271</imagelabel> </seclabel></domain>

  Read the article

• Large concurrent user performance issues for Apache + mod_jk + GlassFish v3.1 clusters

  - by user10035

  I am running a java ee 6 ear application on a GlassFish v3.1 ( 2 clusters with 2 instances each) load balanced by an Apache v2.2 with mod_jk - all on the same server (Windows Server 2003 R2, Intel Xeon CPU x5670 @2.93Ghz, 6GB RAM, 2 cpus). The web application is accessed by around ~100 users. When they all try to access it at the same time every morning ~8am, the response is very slow while trying to access the main jsf home page. Apart from that I have seen the CPU usage spike upto 99% by the httpd process during the day frequently and I start seeing errors in the mod_jk.log file. [Wed Jun 08 08:25:43 2011] [9380:8216] [info] ajp_process_callback::jk_ajp_common.c (1885): Writing to client aborted or client network problems [Wed Jun 08 08:25:43 2011] [9380:8216] [info] ajp_service::jk_ajp_common.c (2543): (myAppLocalInstance4) sending request to tomcat failed (unrecoverable), because of client write error (attempt=1) Any suggestions on how I can go about improving this? Apache configuration is mostly the default as shown below ServerRoot "C:/Program Files/Apache Software Foundation/Apache2.2" Listen 80 LoadModule actions_module modules/mod_actions.so LoadModule alias_module modules/mod_alias.so LoadModule asis_module modules/mod_asis.so LoadModule auth_basic_module modules/mod_auth_basic.so LoadModule authn_default_module modules/mod_authn_default.so LoadModule authn_file_module modules/mod_authn_file.so LoadModule authz_default_module modules/mod_authz_default.so LoadModule authz_groupfile_module modules/mod_authz_groupfile.so LoadModule authz_host_module modules/mod_authz_host.so LoadModule authz_user_module modules/mod_authz_user.so LoadModule autoindex_module modules/mod_autoindex.so LoadModule cgi_module modules/mod_cgi.so LoadModule dir_module modules/mod_dir.so LoadModule env_module modules/mod_env.so LoadModule include_module modules/mod_include.so LoadModule isapi_module modules/mod_isapi.so LoadModule log_config_module modules/mod_log_config.so LoadModule mime_module modules/mod_mime.so LoadModule negotiation_module modules/mod_negotiation.so LoadModule setenvif_module modules/mod_setenvif.so <IfModule !mpm_netware_module> <IfModule !mpm_winnt_module> User daemon Group daemon </IfModule> </IfModule> DocumentRoot "C:/Program Files/Apache Software Foundation/Apache2.2/htdocs" <Directory /> Options FollowSymLinks AllowOverride None Order deny,allow Deny from all </Directory> <Directory "C:/Program Files/Apache Software Foundation/Apache2.2/htdocs"> Options Indexes FollowSymLinks AllowOverride None Order allow,deny Allow from all </Directory> <IfModule dir_module> DirectoryIndex index.html </IfModule> <FilesMatch "^\.ht"> Order allow,deny Deny from all Satisfy All </FilesMatch> ErrorLog "logs/error.log" LogLevel warn <IfModule log_config_module> LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\"" combined LogFormat "%h %l %u %t \"%r\" %>s %b" common <IfModule logio_module> LogFormat "%h %l %u %t \"%r\" %>s %b \"%{Referer}i\" \"%{User-Agent}i\" %I %O" combinedio </IfModule> CustomLog "logs/access.log" common </IfModule> <IfModule alias_module> ScriptAlias /cgi-bin/ "C:/Program Files/Apache Software Foundation/Apache2.2/cgi-bin/" </IfModule> <Directory "C:/Program Files/Apache Software Foundation/Apache2.2/cgi-bin"> AllowOverride None Options None Order allow,deny Allow from all </Directory> DefaultType text/plain <IfModule mime_module> TypesConfig conf/mime.types AddType application/x-compress .Z AddType application/x-gzip .gz .tgz </IfModule> Include conf/extra/httpd-mpm.conf <IfModule ssl_module> SSLRandomSeed startup builtin SSLRandomSeed connect builtin </IfModule> LoadModule jk_module modules/mod_jk.so JkWorkersFile conf/workers.properties JkLogFile logs/mod_jk.log JkLogLevel info JkLogStampFormat "[%a %b %d %H:%M:%S %Y] " JkOptions +ForwardKeySize +ForwardURICompat -ForwardDirectories JkRequestLogFormat "%w %V %T" JkMount /myApp/* loadbalancerLocal JkMount /myAppRemote/* loadbalancerRemote JkMount /myApp loadbalancerLocal JkMount /myAppRemote loadbalancerRemote The workers.properties config file is: worker.list=loadbalancerLocal,loadbalancerRemote worker.myAppLocalInstance1.type=ajp13 worker.myAppLocalInstance1.host=localhost worker.myAppLocalInstance1.port=8109 worker.myAppLocalInstance1.lbfactor=1 worker.myAppLocalInstance1.socket_keepalive=1 worker.myAppLocalInstance1.socket_timeout=1000 worker.myAppLocalInstance2.type=ajp13 worker.myAppLocalInstance2.host=localhost worker.myAppLocalInstance2.port=8209 worker.myAppLocalInstance2.lbfactor=1 worker.myAppLocalInstance2.socket_keepalive=1 worker.myAppLocalInstance2.socket_timeout=1000 worker.myAppLocalInstance3.type=ajp13 worker.myAppLocalInstance3.host=localhost worker.myAppLocalInstance3.port=8309 worker.myAppLocalInstance3.lbfactor=1 worker.myAppLocalInstance3.socket_keepalive=1 worker.myAppLocalInstance3.socket_timeout=1000 worker.myAppLocalInstance4.type=ajp13 worker.myAppLocalInstance4.host=localhost worker.myAppLocalInstance4.port=8409 worker.myAppLocalInstance4.lbfactor=1 worker.myAppLocalInstance4.socket_keepalive=1 worker.myAppLocalInstance4.socket_timeout=1000 worker.myAppRemoteInstance1.type=ajp13 worker.myAppRemoteInstance1.host=localhost worker.myAppRemoteInstance1.port=8509 worker.myAppRemoteInstance1.lbfactor=1 worker.myAppRemoteInstance1.socket_keepalive=1 worker.myAppRemoteInstance1.socket_timeout=1000 worker.myAppRemoteInstance2.type=ajp13 worker.myAppRemoteInstance2.host=localhost worker.myAppRemoteInstance2.port=8609 worker.myAppRemoteInstance2.lbfactor=1 worker.myAppRemoteInstance2.socket_keepalive=1 worker.myAppRemoteInstance2.socket_timeout=1000 worker.myAppRemoteInstance3.type=ajp13 worker.myAppRemoteInstance3.host=localhost worker.myAppRemoteInstance3.port=8709 worker.myAppRemoteInstance3.lbfactor=1 worker.myAppRemoteInstance3.socket_keepalive=1 worker.myAppRemoteInstance3.socket_timeout=1000 worker.myAppRemoteInstance4.type=ajp13 worker.myAppRemoteInstance4.host=localhost worker.myAppRemoteInstance4.port=8809 worker.myAppRemoteInstance4.lbfactor=1 worker.myAppRemoteInstance4.socket_keepalive=1 worker.myAppRemoteInstance4.socket_timeout=1000 worker.loadbalancerLocal.type=lb worker.loadbalancerLocal.sticky_session=True worker.loadbalancerLocal.balance_workers=myAppLocalInstance1,myAppLocalInstance2,myAppLocalInstance3,myAppLocalInstance4 worker.loadbalancerRemote.type=lb worker.loadbalancerRemote.balance_workers=myAppRemoteInstance1,myAppRemoteInstance2,myAppRemoteInstance3,myAppRemoteInstance4 worker.loadbalancerRemote.sticky_session=True

  Read the article

• How does this main domain have a CNAME record?

  - by TRiG

  I was under the impression that only subdomains could have CNAME records: main domains need to define all their own records. However, apt-get.com seems to have only a CNAME record. How can this work? $ dig apt-get.com ; <<>> DiG 9.8.1-P1 <<>> apt-get.com ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 45743 ;; flags: qr rd ra; QUERY: 1, ANSWER: 9, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;apt-get.com. IN A ;; ANSWER SECTION: apt-get.com. 86336 IN CNAME thie5ku9.dsgeneration.com. thie5ku9.dsgeneration.com. 60 IN A 208.73.211.242 thie5ku9.dsgeneration.com. 60 IN A 208.73.211.246 thie5ku9.dsgeneration.com. 60 IN A 208.73.211.166 thie5ku9.dsgeneration.com. 60 IN A 208.73.211.232 thie5ku9.dsgeneration.com. 60 IN A 208.73.211.161 thie5ku9.dsgeneration.com. 60 IN A 208.73.210.233 thie5ku9.dsgeneration.com. 60 IN A 208.73.211.186 thie5ku9.dsgeneration.com. 60 IN A 208.73.211.188 ;; Query time: 59 msec ;; SERVER: 127.0.0.1#53(127.0.0.1) ;; WHEN: Tue Jun 10 15:05:48 2014 ;; MSG SIZE rcvd: 193 $ dig apt-get.com ns ; <<>> DiG 9.8.1-P1 <<>> apt-get.com ns ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: SERVFAIL, id: 43831 ;; flags: qr rd ra; QUERY: 1, ANSWER: 0, AUTHORITY: 0, ADDITIONAL: 0 ;; QUESTION SECTION: ;apt-get.com. IN NS ;; Query time: 26 msec ;; SERVER: 127.0.0.1#53(127.0.0.1) ;; WHEN: Tue Jun 10 15:12:37 2014 ;; MSG SIZE rcvd: 29 $ dig apt-get.com ns @b.gtld-servers.net ; <<>> DiG 9.8.1-P1 <<>> apt-get.com ns @b.gtld-servers.net ;; global options: +cmd ;; Got answer: ;; ->>HEADER<<- opcode: QUERY, status: NOERROR, id: 38228 ;; flags: qr rd; QUERY: 1, ANSWER: 0, AUTHORITY: 2, ADDITIONAL: 2 ;; WARNING: recursion requested but not available ;; QUESTION SECTION: ;apt-get.com. IN NS ;; AUTHORITY SECTION: apt-get.com. 172800 IN NS ns1.domainrecover.com. apt-get.com. 172800 IN NS ns2.domainrecover.com. ;; ADDITIONAL SECTION: ns1.domainrecover.com. 172800 IN A 66.45.232.66 ns2.domainrecover.com. 172800 IN A 65.23.159.179 ;; Query time: 70 msec ;; SERVER: 192.33.14.30#53(192.33.14.30) ;; WHEN: Tue Jun 10 15:07:05 2014 ;; MSG SIZE rcvd: 111 The domain does resolve. I get the following headers: GET / HTTP/1.1 User-Agent: Testing_Sniffer/4.15 Host: apt-get.com Accept: */* HTTP/1.0 200 (OK) Cache-Control: private, no-cache, must-revalidate Connection: Keep-Alive Pragma: no-cache Server: Oversee Turing v1.0.0 Content-Length: 1347 Content-Type: text/html Expires: Mon, 26 Jul 1997 05:00:00 GMT Keep-Alive: timeout=3, max=96 P3P: policyref="http://www.dsparking.com/w3c/p3p.xml", CP="NOI DSP COR ADMa OUR NOR STA" Set-Cookie: parkinglot=1; domain=.apt-get.com; path=/; expires=Wed, 11-Jun-2014 14:10:37 GMT <!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.01 Frameset//EN" "http://www.w3.org/TR/html4/frameset.dtd"> <!-- turing_cluster_prod --> <html> <head> <meta http-equiv="Content-Type" content="text/html; charset=utf-8" /> <title>apt-get.com</title> <meta name="keywords" content="apt-get.com" /> <meta name="description" content="apt-get.com" /> <meta name="robots" content="index, follow" /> <meta name="revisit-after" content="10" /> <meta name="viewport" content="width=device-width, initial-scale=1.0" /> <script type="text/javascript"> document.cookie = "jsc=1"; </script> </head> <frameset rows="100%,*" frameborder="no" border="0" framespacing="0"> <frame src="http://apt-get.com?epl=5PfLSSqWrYDAt-gbwMDK_rA3b1UJCYVTJHfxTzr9FTDQV84b6vAgVhU3FTeCRQNiuRNv79Ni0V3mkEVNRhpqo2gpMjp5iOIR1w2_EISPENaqzoXohVXl2QI3ryXlRCB4FaIIaxynnWXWY6QBgBgNiIZ6agD1NBoNGg0ajXpUCXUAIJDer78AAOB_AwAAQIDbCwAAe_NWlVlTJllBMTZoWkKPAAAA8A" name="apt-get.com"> </frameset> <noframes> <body><a href="http://apt-get.com?epl=5PfLSSqWrYDAt-gbwMDK_rA3b1UJCYVTJHfxTzr9FTDQV84b6vAgVhU3FTeCRQNiuRNv79Ni0V3mkEVNRhpqo2gpMjp5iOIR1w2_EISPENaqzoXohVXl2QI3ryXlRCB4FaIIaxynnWXWY6QBgBgNiIZ6agD1NBoNGg0ajXpUCXUAIJDer78AAOB_AwAAQIDbCwAAe_NWlVlTJllBMTZoWkKPAAAA8A">Click here to go to apt-get.com</a>.</body> </noframes> </html>

  Read the article

• Moving a Drupal between linux servers, best practice to avoid file-ownership problems

  - by zero

  I want to port over a Drupal commons 6x24 from a local LAMP-stack to a production webserver. Both systems run OpenSuse Linux. How do I do this, what are the most important steps. How should I handle file-ownership. It's important for me to have to have full control of the file ownership. If I use the wwwrun account, I frequently run into problems, due to a very strict webserver-admin. See for example the long history of looking for fixes and solutions see this thread and even more interesting see this very long and impressive thread here. All troubles I run into have to do with file-owernship and permissions. This is my current setup; Note: This was just a quick hacked installation - quick and dirty. Well my interest is after the general options i have in the port of a drupal from linux to linux linux-vi17:/srv/www/htdocs/com624 # ls -l insgesamt 224 -rwxrwxrwx 1 root www 45285 19. Jan 00:54 CHANGELOG.txt -rwxrwxrwx 1 root www 925 19. Jan 00:54 COPYRIGHT.txt -rwxrwxrwx 1 root www 206 19. Jan 00:54 cron.php drwxrwxrwx 2 root www 4096 19. Jan 00:54 includes -rwxrwxrwx 1 root www 923 19. Jan 00:54 index.php -rwxrwxrwx 1 root www 1244 19. Jan 00:54 INSTALL.mysql.txt -rwxrwxrwx 1 root www 1011 19. Jan 00:54 INSTALL.pgsql.txt -rwxrwxrwx 1 root www 47073 19. Jan 00:54 install.php -rwxrwxrwx 1 root www 15572 19. Jan 00:54 INSTALL.txt -rwxrwxrwx 1 root www 14940 19. Jan 00:54 LICENSE.txt -rwxrwxrwx 1 root www 1858 19. Jan 00:54 MAINTAINERS.txt drwxrwxrwx 3 root www 4096 19. Jan 00:54 misc drwxrwxrwx 35 root www 4096 19. Jan 00:54 modules drwxrwxrwx 4 root www 4096 19. Jan 00:54 profiles -rwxrwxrwx 1 root www 1470 19. Jan 00:54 robots.txt drwxrwxrwx 2 root www 4096 19. Jan 00:54 scripts drwxrwxrwx 4 root www 4096 19. Jan 00:54 sites drwxrwxrwx 7 root www 4096 19. Jan 00:54 themes -rwxrwxrwx 1 root www 26250 19. Jan 00:54 update.php -rwxrwxrwx 1 root www 4864 19. Jan 00:54 UPGRADE.txt -rwxrwxrwx 1 root www 294 19. Jan 00:54 xmlrpc.php linux-vi17:/srv/www/htdocs/com624 # thx to BetaRides answer here a quick overview on the drush functionality with rsync http://drush.ws/ core-rsync Rsync the Drupal tree to/from another server using ssh. Examples: drush rsync @dev @stage Rsync Drupal root from dev to stage (one of which must be local). drush rsync ./ @stage:%files/img Rsync all files in the current directory to the 'img' directory in the file storage folder on stage. Arguments: source May be rsync path or site alias. See rsync documentation and example.aliases.drushrc.php. destination May be rsync path or site alias. See rsync documentation and example.aliases.drushrc.php. Options: --mode The unary flags to pass to rsync; --mode=rultz implies rsync -rultz. Default is -az. --RSYNC-FLAG Most rsync flags passed to drush sync will be passed on to rsync. See rsync documentation. --exclude-conf Excludes settings.php from being rsynced. Default. --include-conf Allow settings.php to be rsynced --exclude-files Exclude the files directory. --exclude-sites Exclude all directories in "sites/" except for "sites/all". --exclude-other-sites Exclude all directories in "sites/" except for "sites/all" and the site directory for the site being synced. Note: if the site directory is different between the source and destination, use --exclude-sites followed by "drush rsync @from:%site @to:%site" --exclude-paths List of paths to exclude, seperated by : (Unix-based systems) or ; (Windows). --include-paths List of paths to include, seperated by : (Unix-based systems) or ; (Windows). Topics: docs-aliases Site aliases overview with examples Aliases: rsync

  Read the article

• Windows 7: Search indexing is stuck

  - by Ricket

  When I open Indexing Options, it says: 4,317 items indexed Indexing in progress. Search results might not be complete during this time. It's stuck at 4,317 though; no more items have been indexed. Worst of all, SearchIndexer.exe is taking up 100% CPU (well, 50%, but I have a dual core CPU; it's taking up all processing power it can). It is not causing hard drive activity though. I tried clicking "Troubleshoot search and indexing" at the bottom of the Indexing Options window, but it couldn't find any problem. I've also tried the repair registry key that several websites suggest; I change HKLM\SOFTWARE\Microsoft\Windows Search SetupCompletedSuccessfully to 0 and restarted the computer, and it apparently repaired because it flipped back to 1, but the same problem continues to occur. It's reducing the battery life of my laptop and making it really hot so that my fans are running all the time. I've had to disable the Windows Search service. How can I fix this? Do I need to just flat-out reformat my computer? Update: I've tried rebuilding a couple times. There's nothing unusual about the locations I have to index, and I don't have any downloads in progress or anything like that. I don't see any reason why it stopped, and I noticed it much too late to do a system restore. At this point, I'm hoping someone will offer up some secret answer that will fix the problem, thus the bounty. Another update: I tried starting the service again, just to let it try yet again. It seemed okay at first (Indexing Options showed it operating at reduced speed due to user activity, and the number of files was going up). A while later I checked, and the service had stopped. Event viewer revealed some errors like this: Log Name: Application Source: Application Error Date: 2/1/2010 7:34:23 PM Event ID: 1000 Task Category: (100) Level: Error Keywords: Classic User: N/A Computer: ricky-win7 Description: Faulting application name: SearchIndexer.exe, version: 7.0.7600.16385, time stamp: 0x4a5bcdd0 Faulting module name: NLSData0007.dll, version: 6.1.7600.16385, time stamp: 0x4a5bda88 Exception code: 0xc0000005 Fault offset: 0x002141ba Faulting process id: 0x13a0 Faulting application start time: 0x01caa39f2a70ec02 Faulting application path: C:\Windows\system32\SearchIndexer.exe Faulting module path: C:\Windows\System32\NLSData0007.dll Report Id: b4f7a7ae-0f92-11df-87fc-e5d65d8794c2 Event Xml: <Event xmlns="http://schemas.microsoft.com/win/2004/08/events/event"> <System> <Provider Name="Application Error" /> <EventID Qualifiers="0">1000</EventID> <Level>2</Level> <Task>100</Task> <Keywords>0x80000000000000</Keywords> <TimeCreated SystemTime="2010-02-02T00:34:23.000000000Z" /> <EventRecordID>10689</EventRecordID> <Channel>Application</Channel> <Computer>ricky-win7</Computer> <Security /> </System> <EventData> <Data>SearchIndexer.exe</Data> <Data>7.0.7600.16385</Data> <Data>4a5bcdd0</Data> <Data>NLSData0007.dll</Data> <Data>6.1.7600.16385</Data> <Data>4a5bda88</Data> <Data>c0000005</Data> <Data>002141ba</Data> <Data>13a0</Data> <Data>01caa39f2a70ec02</Data> <Data>C:\Windows\system32\SearchIndexer.exe</Data> <Data>C:\Windows\System32\NLSData0007.dll</Data> <Data>b4f7a7ae-0f92-11df-87fc-e5d65d8794c2</Data> </EventData> </Event> If you are having the same error and arrived here from a Google search, please comment or add an answer detailing your progress on this, if any...

  Read the article

• How to add addtional disks to a Windows 2008 KVM based Guest?

  - by taazaa

  I have a Win 2008 KVM based guest VM running on a Ubuntu 10 host. It is a raw image of 22G. I want to add a "data" drive which would show up as "D:\" drive on the guest. I first created a raw image using: qemu-img create -f raw ~/vmdisk2.img 50G Then, tried attaching it using virsh attach-disk. When that did not work, I tried editing the xml file of the VM directly. Both did not seem to work. I would greatly appreciate any help on how to do this and what the best practice is. I want to keep the base image small, so that I can clone it (hopefully) and then attach necessary storage based on the application at hand. Update: The xml of the vm before adding the second drive: <domain type='kvm'> <name>win08e-vm1</name> <uuid>183a4ba0-1c0b-0b04-ad01-aa7c3a4cb390</uuid> <memory>1048576</memory> <currentMemory>1048576</currentMemory> <vcpu>2</vcpu> <os> <type arch='x86_64' machine='pc-0.12'>hvm</type> <boot dev='hd'/> </os> <features> <acpi/> <apic/> <pae/> </features> <clock offset='localtime'/> <on_poweroff>destroy</on_poweroff> <on_reboot>restart</on_reboot> <on_crash>restart</on_crash> <devices> <emulator>/usr/bin/kvm</emulator> <disk type='file' device='disk'> <driver name='qemu' type='raw'/> <source file='/var/lib/libvirt/images/win08e-vm1.img'/> <target dev='hda' bus='ide'/> <address type='drive' controller='0' bus='0' unit='0'/> </disk> <disk type='file' device='cdrom'> <driver name='qemu' type='raw'/> <source file='/home/taazaa/iso/Win08ER264.iso'/> <target dev='hdc' bus='ide'/> <readonly/> <address type='drive' controller='0' bus='1' unit='0'/> </disk> <controller type='ide' index='0'> <address type='pci' domain='0x0000' bus='0x00' slot='0x01' function='0x1'/> </controller> <interface type='bridge'> <mac address='52:54:00:7f:a7:ae'/> <source bridge='br0'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x03' function='0x0'/> </interface> <serial type='pty'> <target port='0'/> </serial> <console type='pty'> <target type='serial' port='0'/> </console> <input type='tablet' bus='usb'/> <input type='mouse' bus='ps2'/> <graphics type='vnc' port='-1' autoport='yes' keymap='en-us'/> <video> <model type='vga' vram='9216' heads='1'/> <address type='pci' domain='0x0000' bus='0x00' slot='0x02' function='0x0'/> </video> <memballoon model='virtio'> <address type='pci' domain='0x0000' bus='0x00' slot='0x04' function='0x0'/> </memballoon> </devices> </domain> Thanks!

  Read the article

• SignalR cannot read property client of undefined

  - by polonskyg

  I'm trying to add SignalR to my project (ASPNET MVC 4). But I can't make it work. In the below image you can see the error I'm receiving. I've read a lot of stackoverflow posts but none of them is resolving my issue. This is what I did so far: 1) Ran Install-Package Microsoft.AspNet.SignalR -Pre 2) Added RouteTable.Routes.MapHubs(); in Global.asax.cs Application_Start() 3) If I go to http://localhost:9096/Gdp.IServer.Web/signalr/hubs I can see the file content 4) Added <modules runAllManagedModulesForAllRequests="true"/> to Web.Config 5) Created folder Hubs in the root of the MVC application 6) Moved jquery and signalR scripts to /Scripts/lib folder (I'm not using jquery 1.6.4, I'm using the latest) This is my Index.cshtml <h2>List of Messages</h2> <div class="container"> <input type="text" id="message" /> <input type="button" id="sendmessage" value="Send" /> <input type="hidden" id="displayname" /> <ul id="discussion"> </ul> </div> @section pageScripts { <!--Reference the SignalR library. --> <script src="@Url.Content("~/Scripts/jquery.signalR-1.0.0-rc1.min.js")" type="text/javascript"></script> <!--Reference the autogenerated SignalR hub script. --> <script type="text/javascript" src="~/signalr/hubs"></script> <script src="@Url.Content("~/Scripts/map.js")" type="text/javascript"></script> } This is my IServerHub.cs file (located inside Hubs folder) namespace Gdp.IServer.Ui.Web.Hubs { using Microsoft.AspNet.SignalR.Hubs; [HubName("iServerHub")] public class IServerHub : Hub { public void Send(string name, string message) { Clients.All.broadcastMessage(name, message); } } } And this is map.js $(function () { // Declare a proxy to reference the hub. var clientServerHub = $.connection.iServerHub; // Create a function that the hub can call to broadcast messages. clientServerHub.client.broadcastMessage = function (name, message) { $('#discussion').append('<li><strong>' + name + '</strong>:&nbsp;&nbsp;' + message + '</li>'); }; // Get the user name and store it to prepend to messages. $('#displayname').val(prompt('Enter your name:', '')); // Set initial focus to message input box. $('#message').focus(); // Start the connection. $.connection.hub.start().done(function () { $('#sendmessage').click(function () { // Html encode display name and message. var encodedName = $('<div />').text($('#displayname').val()).html(); var encodedMsg = $('<div />').text($('#message').val()).html(); // Call the Send method on the hub. clientServerHub.server.send(encodedName, encodedMsg); // Clear text box and reset focus for next comment. $('#message').val('').focus(); }); }); }); The DLL's I see references for SignalR are: Microsoft.AspNet.SignalR.Core Microsoft.AspNet.SignalR.Owin Microsoft.AspNet.SignalR.SystemWeb Any ideas how to get it work? Should I make any change because the scripts are in /Script/lib folder? NOTE I'm following the instruction found here on how to set up Windsor Castle to make it work with SignalR, and again, seems that the proxy cannot be created and I'm getting the same error: Cannot read property client of undefined meaning that the proxy to the hub was not created This is how I have it in the server public class IncidentServerHub : Hub and like this in the client var clientServerHub = $.connection.incidentServerHub; Again, I can see the dynamically created file here: /GdpSoftware.Server.Web/signalr/hubs So, Why the proxy is not created? Thanks in advance!!! Guillermo.

  Read the article

• git | error: Unable to append to .git/logs/refs/remotes/origin/master: Permission denied [SOLVED]

  - by Corbin Tarrant

  I am having a strange issue that I can't seem to resolve. Here is what happend: I had some log files in a github repository that I didn't want there. I found this script that removes files completely from git history like so: #!/bin/bash set -o errexit # Author: David Underhill # Script to permanently delete files/folders from your git repository. To use # it, cd to your repository's root and then run the script with a list of paths # you want to delete, e.g., git-delete-history path1 path2 if [ $# -eq 0 ]; then exit 0are still fi # make sure we're at the root of git repo if [ ! -d .git ]; then echo "Error: must run this script from the root of a git repository" exit 1 fi # remove all paths passed as arguments from the history of the repo files=$@ git filter-branch --index-filter "git rm -rf --cached --ignore-unmatch $files" HEAD # remove the temporary history git-filter-branch otherwise leaves behind for a long time rm -rf .git/refs/original/ && git reflog expire --all && git gc --aggressive --prune I, of course, made a backup first and then tried it. It seemed to work fine. I then did a git push -f and was greeted with the following messages: error: Unable to append to .git/logs/refs/remotes/origin/master: Permission denied error: Cannot update the ref 'refs/remotes/origin/master'. Everything seems to have pushed fine though, because the files seem to be gone from the GitHub repository, if I try and push again I get the same thing: error: Unable to append to .git/logs/refs/remotes/origin/master: Permission denied error: Cannot update the ref 'refs/remotes/origin/master'. Everything up-to-date EDIT $ sudo chgrp {user} .git/logs/refs/remotes/origin/master $ sudo chown {user} .git/logs/refs/remotes/origin/master $ git push Everything up-to-date Thanks! EDIT Uh Oh. Problem. I've been working on this project all night and just went to commit my changes: error: Unable to append to .git/logs/refs/heads/master: Permission denied fatal: cannot update HEAD ref So I: sudo chown {user} .git/logs/refs/heads/master sudo chgrp {user} .git/logs/refs/heads/master I try the commit again and I get: error: Unable to append to .git/logs/HEAD: Permission denied fatal: cannot update HEAD ref So I: sudo chown {user} .git/logs/HEAD sudo chgrp {user} .git/logs/HEAD And then I try the commit again: 16 files changed, 499 insertions(+), 284 deletions(-) create mode 100644 logs/DBerrors.xsl delete mode 100644 logs/emptyPHPerrors.php create mode 100644 logs/trimXMLerrors.php rewrite public/codeCore/Classes/php/DatabaseConnection.php (77%) create mode 100644 public/codeSite/php/init.php $ git push Counting objects: 49, done. Delta compression using up to 2 threads. Compressing objects: 100% (27/27), done. Writing objects: 100% (27/27), 7.72 KiB, done. Total 27 (delta 15), reused 0 (delta 0) To [email protected]:IAmCorbin/MooKit.git 59da24e..68b6397 master -> master Hooray. I jump on http://GitHub.com and check out the repository, and my latest commit is no where to be found. ::scratch head:: So I push again: Everything up-to-date Umm...it doesn't look like it. I've never had this issue before, could this be a problem with github? or did I mess something up with my git project? EDIT Nevermind, I did a simple: git push origin master and it pushed fine.

  Read the article

• Bluetooth RFCOMM / SDP connection to a RS232 adapter in android

  - by ThePosey

  Hello All, I am trying to use the Bluetooth Chat sample API app that google provides to connect to a bluetooth RS232 adapter hooked up to another device. Here is the app for reference: http://developer.android.com/resources/samples/BluetoothChat/index.html And here is the spec sheet for the RS232 connector just for reference: http://serialio.com/download/Docs/BlueSnap-guide-4.77_Commands.pdf Well the problem is that when I go to connect to the device with: mmSocket.connect(); (BluetoothSocket::connect()) I always get an IOException error thrown by the connect() method. When I do a toString on the exception I get "Service discovery failed". My question is mostly what are the cases that would cause an IOException to get thrown in the connect method? I know those are in the source somewhere but I don't know exactly how the java layer that you write apps in and the C/C++ layer that contains the actual stacks interface. I know that it uses the bluez bluetooth stack which is written in C/C++ but not sure how that ties into the java layer which is what I would think is throwing the exception. Any help on pointing me to where I can try to dissect this issue would be incredible. Also just to note I am able to pair with the RS232 adapter just fine but I am never able to actually connect. Here is the logcat output for more reference: I/ActivityManager( 1018): Displayed activity com.example.android.BluetoothChat/.DeviceListActivity: 326 ms (total 326 ms) E/BluetoothService.cpp( 1018): stopDiscoveryNative: D-Bus error in StopDiscovery: org.bluez.Error.Failed (Invalid discovery session) D/BluetoothChat( 1729): onActivityResult -1 D/BluetoothChatService( 1729): connect to: 00:06:66:03:0C:51 D/BluetoothChatService( 1729): setState() STATE_LISTEN - STATE_CONNECTING E/BluetoothChat( 1729): + ON RESUME + I/BluetoothChat( 1729): MESSAGE_STATE_CHANGE: STATE_CONNECTING I/BluetoothChatService( 1729): BEGIN mConnectThread E/BluetoothService.cpp( 1018): stopDiscoveryNative: D-Bus error in StopDiscovery: org.bluez.Error.Failed (Invalid discovery session) E/BluetoothEventLoop.cpp( 1018): event_filter: Received signal org.bluez.Device:PropertyChanged from /org/bluez/1498/hci0/dev_00_06_66_03_0C_51 I/BluetoothChatService( 1729): CONNECTION FAIL TOSTRING: java.io.IOException: Service discovery failed D/BluetoothChatService( 1729): setState() STATE_CONNECTING - STATE_LISTEN D/BluetoothChatService( 1729): start D/BluetoothChatService( 1729): setState() STATE_LISTEN - STATE_LISTEN I/BluetoothChat( 1729): MESSAGE_STATE_CHANGE: STATE_LISTEN V/BluetoothEventRedirector( 1080): Received android.bleutooth.device.action.UUID I/NotificationService( 1018): enqueueToast pkg=com.example.android.BluetoothChat callback=android.app.ITransientNotification$Stub$Proxy@446327c8 duration=0 I/BluetoothChat( 1729): MESSAGE_STATE_CHANGE: STATE_LISTEN E/BluetoothEventLoop.cpp( 1018): event_filter: Received signal org.bluez.Device:PropertyChanged from /org/bluez/1498/hci0/dev_00_06_66_03_0C_51 V/BluetoothEventRedirector( 1080): Received android.bleutooth.device.action.UUID The device I'm trying to connect to is the 00:06:66:03:0C:51 which I can scan for and apparently pair with just fine. The below is merged from a similar question which was successfully resolved by the selected answer here: How can one connect to an rfcomm device other than another phone in Android? The Android API provides examples of using listenUsingRfcommWithServiceRecord() to set up a socket and createRfcommSocketToServiceRecord() to connect to that socket. I'm trying to connect to an embedded device with a BlueSMiRF Gold chip. My working Python code (using the PyBluez library), which I'd like to port to Android, is as follows: sock = bluetooth.BluetoothSocket(proto=bluetooth.RFCOMM) sock.connect((device_addr, 1)) return sock.makefile() ...so the service to connect to is simply defined as channel 1, without any SDP lookup. As the only documented mechanism I see in the Android API does SDP lookup of a UUID, I'm slightly at a loss. Using "sdptool browse" from my Linux host comes up empty, so I surmise that the chip in question simply lacks SDP support.

  Read the article

• Why does WPF Style to show validation errors in ToolTip work for a TextBox but fails for a ComboBox?

  - by Mike B

  I am using a typical Style to display validation errors as a tooltip from IErrorDataInfo for a textbox as shown below and it works fine. <Style TargetType="{x:Type TextBox}"> <Style.Triggers> <Trigger Property="Validation.HasError" Value="true"> <Setter Property="ToolTip" Value="{Binding RelativeSource={RelativeSource Self}, Path=(Validation.Errors)[0].ErrorContent}"/> </Trigger> </Style.Triggers> </Style> But when i try to do the same thing for a ComboBox like this it fails <Style TargetType="{x:Type ComboBox}"> <Style.Triggers> <Trigger Property="Validation.HasError" Value="true"> <Setter Property="ToolTip" Value="{Binding RelativeSource={RelativeSource Self}, Path=(Validation.Errors)[0].ErrorContent}"/> </Trigger> </Style.Triggers> </Style> The error I get in the output window is: System.Windows.Data Error: 17 : Cannot get 'Item[]' value (type 'ValidationError') from '(Validation.Errors)' (type 'ReadOnlyObservableCollection`1'). BindingExpression:Path=(0)[0].ErrorContent; DataItem='ComboBox' (Name='ownerComboBox'); target element is 'ComboBox' (Name='ownerComboBox'); target property is 'ToolTip' (type 'Object') ArgumentOutOfRangeException:'System.ArgumentOutOfRangeException: Specified argument was out of the range of valid values.Parameter name: index' Oddly it also attempts to make invalid Database changes when I close the window if I change any ComboBox values (This is also when the binding error occurs)!!! Cannot insert the value NULL into column 'EmpFirstName', table 'OITaskManager.dbo.Employees'; column does not allow nulls. INSERT fails. The statement has been terminated. Simply by commenting the style out everyting works perfectly. How do I fix this? Just in case anyone needs it one of the comboBox' xaml follows: <ComboBox ItemsSource="{Binding Path=Employees}" SelectedValuePath="EmpID" SelectedValue="{Binding Path=SelectedIssue.Employee2.EmpID, Mode=OneWay, ValidatesOnDataErrors=True}" ItemTemplate="{StaticResource LastNameFirstComboBoxTemplate}" Height="28" Name="ownerComboBox" Width="120" Margin="2" SelectionChanged="ownerComboBox_SelectionChanged" /> <DataTemplate x:Key="LastNameFirstComboBoxTemplate"> <TextBlock> <TextBlock.Text> <MultiBinding StringFormat="{}{1}, {0}" > <Binding Path="EmpFirstName" /> <Binding Path="EmpLastName" /> </MultiBinding> </TextBlock.Text> </TextBlock> </DataTemplate> SelectionChanged: (I do plan to implement commanding before long but, as this is my first WPF project I have not gone full MVVM yet. I am trying to take things in small-medium sized bites) // This is done this way to maintain the DataContext Integrity // and avoid an error due to an Object being "Not New" in Linq-to-SQL private void ownerComboBox_SelectionChanged(object sender, SelectionChangedEventArgs e) { Employee currentEmpl = ownerComboBox.SelectedItem as Employee; if (currentEmpl != null && currentEmpl != statusBoardViewModel.SelectedIssue.Employee2) { statusBoardViewModel.SelectedIssue.Employee2 = currentEmpl; } }

  Read the article

• Random Access Violation Exception in WPF Application

  - by PT1984

  Hi, I am facing weird problem while running regression tests on my WPF Application. I am getting AccessViolationException with different stacktraces each time. First : Message :Attempted to read or write protected memory. This is often an indication that other memory is corrupt. StackTrace : at MS.Win32.PresentationCore.UnsafeNativeMethods.MILUnknown.Release(IntPtr pIUnkown) at MS.Win32.PresentationCore.UnsafeNativeMethods.MILUnknown.ReleaseInterface(IntPtr& ptr) at System.Windows.Media.SafeMILHandle.ReleaseHandle() at System.Runtime.InteropServices.SafeHandle.InternalFinalize() at System.Runtime.InteropServices.SafeHandle.Dispose(Boolean disposing) at System.Runtime.InteropServices.SafeHandle.Finalize() Source :PresentationCore Type : System.AccessViolationException. Second : Message :Attempted to read or write protected memory. This is often an indication that other memory is corrupt. StackTrace : at MS.Win32.PresentationCore.UnsafeNativeMethods.IMILBitmapEffect.GetOutput(SafeHandle THIS_PTR, UInt32 uiIndex, SafeMILHandle pContext, BitmapSourceSafeMILHandle& ppBitmapSource) at System.Windows.Media.Effects.BitmapEffect.GetOutput(SafeHandle unmanagedEffect, Int32 index, BitmapEffectRenderContext context) at System.Windows.Media.Effects.BitmapEffect.GetOutput(BitmapEffectInput input) at System.Windows.Media.Effects.BitmapEffectState.GetEffectOutput(Visual visual, RenderTargetBitmap& renderBitmap, Matrix worldTransform, Rect windowClip, Matrix& finalTransform) at System.Windows.Media.Effects.BitmapEffectVisualState.RenderBitmapEffect(Visual visual, Channel channel) at System.Windows.Media.Effects.BitmapEffectContent.ExecuteRealizationsUpdate() at System.Windows.Media.RealizationContext.RealizationUpdateSchedule.Execute() at System.Windows.Media.MediaContext.Render(ICompositionTarget resizedCompositionTarget) at System.Windows.Media.MediaContext.RenderMessageHandlerCore(Object resizedCompositionTarget) at System.Windows.Media.MediaContext.AnimatedRenderMessageHandler(Object resizedCompositionTarget) at System.Windows.Threading.ExceptionWrapper.InternalRealCall(Delegate callback, Object args, Boolean isSingleParameter) at System.Windows.Threading.ExceptionWrapper.TryCatchWhen(Object source, Delegate callback, Object args, Boolean isSingleParameter, Delegate catchHandler) at System.Windows.Threading.Dispatcher.WrappedInvoke(Delegate callback, Object args, Boolean isSingleParameter, Delegate catchHandler) at System.Windows.Threading.DispatcherOperation.InvokeImpl() at System.Windows.Threading.DispatcherOperation.InvokeInSecurityContext(Object state) at System.Threading.ExecutionContext.runTryCode(Object userData) at System.Runtime.CompilerServices.RuntimeHelpers.ExecuteCodeWithGuaranteedCleanup(TryCode code, CleanupCode backoutCode, Object userData) at System.Threading.ExecutionContext.RunInternal(ExecutionContext executionContext, ContextCallback callback, Object state) at System.Threading.ExecutionContext.Run(ExecutionContext executionContext, ContextCallback callback, Object state) at System.Windows.Threading.DispatcherOperation.Invoke() at System.Windows.Threading.Dispatcher.ProcessQueue() at System.Windows.Threading.Dispatcher.WndProcHook(IntPtr hwnd, Int32 msg, IntPtr wParam, IntPtr lParam, Boolean& handled) at MS.Win32.HwndWrapper.WndProc(IntPtr hwnd, Int32 msg, IntPtr wParam, IntPtr lParam, Boolean& handled) at MS.Win32.HwndSubclass.DispatcherCallbackOperation(Object o) at System.Windows.Threading.ExceptionWrapper.InternalRealCall(Delegate callback, Object args, Boolean isSingleParameter) at System.Windows.Threading.ExceptionWrapper.TryCatchWhen(Object source, Delegate callback, Object args, Boolean isSingleParameter, Delegate catchHandler) at System.Windows.Threading.Dispatcher.WrappedInvoke(Delegate callback, Object args, Boolean isSingleParameter, Delegate catchHandler) at System.Windows.Threading.Dispatcher.InvokeImpl(DispatcherPriority priority, TimeSpan timeout, Delegate method, Object args, Boolean isSingleParameter) at System.Windows.Threading.Dispatcher.Invoke(DispatcherPriority priority, Delegate method, Object arg) at MS.Win32.HwndSubclass.SubclassWndProc(IntPtr hwnd, Int32 msg, IntPtr wParam, IntPtr lParam) at MS.Win32.UnsafeNativeMethods.DispatchMessage(MSG& msg) at System.Windows.Threading.Dispatcher.PushFrameImpl(DispatcherFrame frame) at System.Windows.Threading.Dispatcher.PushFrame(DispatcherFrame frame) at System.Windows.Threading.Dispatcher.Run() at System.Windows.Application.RunDispatcher(Object ignore) at System.Windows.Application.RunInternal(Window window) at System.Windows.Application.Run(Window window) at System.Windows.Application.Run() at Main() Source :PresentationCore Type :System.AccessViolationException In Application Event Log I found following entries : Dispatcher processing has been suspended, but messages are still being processed. Faulting application **.exe, version 1.0.0.*, stamp 4c08d288, faulting module wpfgfx_v0300.dll, version 3.0.6920.1427, stamp 488f3056, debug? 0, fault address 0x0012ec36. My Application uses Dispatcher from another thread, to change the values of the controls , enable - disable those, change visibility etc., the thred is run multiple times in a second. Please let me know if anybody has faced this problem? Thanks in advance, -Prasad

  Read the article

• Getting this CSS to work in IE6

  - by jerrygarciuh

  Hi folks, Working on this page: http://www.karlsenner.dreamhosters.com/about.php and having trouble with the navigation in IE6. It validates as XHTML 1.0 Transitional. Works great in FF, IE 8, Chrome, and Windows Safari. In IE6 and Opera 10 the drop menus appear too high. I tried adding in the different versions of http://code.google.com/p/ie7-js/ but it did not solve the issue in IE. The CSS looks like this: #wrapper { position: relative; display: block; background-color: inherit; margin: 0px auto; padding: 0; width: 900px; min-height: 900px; } #nav {} .navImage { position:relative; display:inline; height:102px; /* added in hopes of helping IE position but no dice */ } .subMenu { position:absolute; z-index:10; background-color:#FFF; top: 14px; left:0; } .subMenu a:link, .subMenu a:visited, .subMenu a:active{ display:block; width:90%; padding:6px; margin:0; color:#3CF; font-family:Tahoma, Geneva, sans-serif; font-size:14px; text-decoration:none; font-weight:bold; } .subMenu a:hover{ display:block; width:90%; padding:6px; margin:0; color:#3CF; background-color:#CCC; font-family:Tahoma, Geneva, sans-serif; font-size:14px; text-decoration:none; font-weight:bold; } jQuery rollovers: $('#navcompany').hover(function () { $('#companyMenu').css('display', 'block'); $('#companyImg').attr('src','g/nav/company_over.gif'); }, function () { $('#companyMenu').css('display', 'none'); $('#companyImg').attr('src','g/nav/company.gif'); }); And one of the cells. Since the menu is coming out of PHP and IE was not respecting the widths I just use PHP to get the nav image widths and write them to styles on the fly. Solved the width issue as IE acted like they should inherit their width from the wrapper. This may be a clue as to why they don't appear below their nav images but I can't sort it. <div id="navcompany" class="navImage" style="width:128px"> <a href="about.php"> <img src="g/nav/company_over.gif" name="companyImg" width="128" height="102" border="0" id="companyImg" alt="company" /> </a> <div id="companyMenu" class="subMenu" style="display:none; width:128px"> <a href="about.php">About us</a> <a href="location.php">Our location</a> </div> </div> Any advice greatly appreciated! JG

  Read the article

• Can't view order in magento

  - by koko

  Hi, I've been setting up a fresh magento 1.4.0.1 install, working great so far. I did some test orders just to see. Everything works fine, but when I click on "view order" under "my orders", I get a bunch of error messages: There has been an error processing your request Notice: iconv_substr() [function.iconv-substr]: Unknown error (0) in /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Helper/String.php on line 98 Trace: #0 [internal function]: mageCoreErrorHandler(8, 'iconv_substr() ...', '/data/web/A1423...', 98, Array) #1 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Helper/String.php(98): iconv_substr('1', 0, 50, 'UTF-8') #2 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Helper/String.php(173): Mage_Core_Helper_String-substr('1', 0, 50) #3 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Helper/String.php(112): Mage_Core_Helper_String-str_split('1', 50) #4 /data/web/A14237/htdocs/magento/app/design/frontend/base/default/template/sales/order/items/renderer/default.phtml(58): Mage_Core_Helper_String-splitInjection('1') #5 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Template.php(189): include('/data/web/A1423...') #6 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Template.php(225): Mage_Core_Block_Template-fetchView('frontend/base/d...') #7 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Template.php(242): Mage_Core_Block_Template-renderView() #8 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Abstract.php(674): Mage_Core_Block_Template-_toHtml() #9 /data/web/A14237/htdocs/magento/app/code/core/Mage/Sales/Block/Items/Abstract.php(137): Mage_Core_Block_Abstract-toHtml() #10 /data/web/A14237/htdocs/magento/app/design/frontend/base/default/template/sales/order/items.phtml(52): Mage_Sales_Block_Items_Abstract-getItemHtml(Object(Mage_Sales_Model_Order_Item)) #11 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Template.php(189): include('/data/web/A1423...') #12 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Template.php(225): Mage_Core_Block_Template-fetchView('frontend/base/d...') #13 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Template.php(242): Mage_Core_Block_Template-renderView() #14 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Abstract.php(674): Mage_Core_Block_Template-_toHtml() #15 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Abstract.php(516): Mage_Core_Block_Abstract-toHtml() #16 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Abstract.php(467): Mage_Core_Block_Abstract-_getChildHtml('order_items', true) #17 /data/web/A14237/htdocs/magento/app/design/frontend/base/default/template/sales/order/view.phtml(64): Mage_Core_Block_Abstract-getChildHtml('order_items') #18 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Template.php(189): include('/data/web/A1423...') #19 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Template.php(225): Mage_Core_Block_Template-fetchView('frontend/base/d...') #20 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Template.php(242): Mage_Core_Block_Template-renderView() #21 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Abstract.php(674): Mage_Core_Block_Template-_toHtml() #22 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Abstract.php(516): Mage_Core_Block_Abstract-toHtml() #23 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Abstract.php(463): Mage_Core_Block_Abstract-_getChildHtml('sales.order.vie...', true) #24 /data/web/A14237/htdocs/magento/app/code/core/Mage/Page/Block/Html/Wrapper.php(52): Mage_Core_Block_Abstract-getChildHtml('', true, true) #25 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Abstract.php(674): Mage_Page_Block_Html_Wrapper-_toHtml() #26 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Text/List.php(43): Mage_Core_Block_Abstract-toHtml() #27 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Abstract.php(674): Mage_Core_Block_Text_List-_toHtml() #28 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Abstract.php(516): Mage_Core_Block_Abstract-toHtml() #29 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Abstract.php(467): Mage_Core_Block_Abstract-_getChildHtml('content', true) #30 /data/web/A14237/htdocs/magento/app/design/frontend/base/default/template/page/2columns-left.phtml(48): Mage_Core_Block_Abstract-getChildHtml('content') #31 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Template.php(189): include('/data/web/A1423...') #32 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Template.php(225): Mage_Core_Block_Template-fetchView('frontend/base/d...') #33 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Template.php(242): Mage_Core_Block_Template-renderView() #34 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Block/Abstract.php(674): Mage_Core_Block_Template-_toHtml() #35 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Model/Layout.php(536): Mage_Core_Block_Abstract-toHtml() #36 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Controller/Varien/Action.php(389): Mage_Core_Model_Layout-getOutput() #37 /data/web/A14237/htdocs/magento/app/code/core/Mage/Sales/controllers/OrderController.php(100): Mage_Core_Controller_Varien_Action-renderLayout() #38 /data/web/A14237/htdocs/magento/app/code/core/Mage/Sales/controllers/OrderController.php(136): Mage_Sales_OrderController-_viewAction() #39 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Controller/Varien/Action.php(418): Mage_Sales_OrderController-viewAction() #40 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Controller/Varien/Router/Standard.php(254): Mage_Core_Controller_Varien_Action-dispatch('view') #41 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Controller/Varien/Front.php(177): Mage_Core_Controller_Varien_Router_Standard-match(Object(Mage_Core_Controller_Request_Http)) #42 /data/web/A14237/htdocs/magento/app/code/core/Mage/Core/Model/App.php(304): Mage_Core_Controller_Varien_Front-dispatch() #43 /data/web/A14237/htdocs/magento/app/Mage.php(596): Mage_Core_Model_App-run(Array) #44 /data/web/A14237/htdocs/magento/index.php(78): Mage::run('', 'store') #45 {main} gtx, koko

  Read the article

• WPF Customized TabControl

  - by xsl

  I have to develop a customized tab control and decided to create it with WPF/XAML, because I planned to learn it anyway. It should look like this when it's finished: I made good progress so far, but there are two issues left: Only the first/last tab item should have a rounded upper-left/bottom-left corner. Is it possible to modify the style of these items, similar to the way I did with the selected tab item? The selected tab item should not have a border on its right side. I tried to accomplish this with z-index and overlapping, but the results were rather disappointing. Is there any other way to do this? XAML: <Window x:Class="MyProject.TestWindow" xmlns="http://schemas.microsoft.com/winfx/2006/xaml/presentation" xmlns:x="http://schemas.microsoft.com/winfx/2006/xaml" Title="TestWindow" Height="350" Width="500" Margin="5" Background="LightGray"> <Window.Resources> <Style TargetType="{x:Type TabControl}"> <Setter Property="Template"> <Setter.Value> <ControlTemplate TargetType="{x:Type TabControl}"> <DockPanel> <Border Margin="0,100,-1,0" Background="#FFAAAAAA" BorderBrush="Gray" CornerRadius="7,0,0,7" BorderThickness="1"> <TabPanel Margin="0,0,0,0" IsItemsHost="True" /> </Border> <Border Background="WhiteSmoke" BorderBrush="Gray" BorderThickness="1" CornerRadius="7,7,7,0" > <ContentPresenter ContentSource="SelectedContent" /> </Border> </DockPanel> </ControlTemplate> </Setter.Value> </Setter> </Style> <Style TargetType="{x:Type TabItem}"> <Setter Property="Template"> <Setter.Value> <ControlTemplate TargetType="{x:Type TabItem}"> <Grid> <Border Name="Border" Background="#FFAAAAAA" CornerRadius="7,0,0,0" BorderBrush="Gray" BorderThickness="0,0,0,1" Margin="0,0,0,0"> <ContentPresenter x:Name="ContentSite" VerticalAlignment="Center" HorizontalAlignment="Left" ContentSource="Header" Margin="10,10,10,10"/> </Border> </Grid> <ControlTemplate.Triggers> <Trigger Property="IsSelected" Value="True"> <Setter TargetName="Border" Property="Background" Value="WhiteSmoke" /> </Trigger> </ControlTemplate.Triggers> </ControlTemplate> </Setter.Value> </Setter> </Style> </Window.Resources> <Grid> <TabControl Name="_menuTabControl" TabStripPlacement="Left" Margin="5"> <TabItem Name="_tabItem1" Header="First Tab Item" ></TabItem> <TabItem Name="_tabItem2" Header="Second Tab Item" > <Grid /> </TabItem> <TabItem Name="_tabItem3" Header="Third Tab Item" > <Grid /> </TabItem> </TabControl> </Grid>

  Read the article

< Previous Page | 654 655 656 657 658 659 660 661 662 663 664 665  | Next Page >