Search Results

Search found 19701 results on 789 pages for 'disk images'.

Page 659/789 | < Previous Page | 655 656 657 658 659 660 661 662 663 664 665 666  | Next Page >

• bond0 and xen = crash

  - by Rajat

  Bonding with xen 1 - Stop all guests. Reboot dom0 after running "chkconfig xend off" and "chkconfig xendomains off". 2 - Configure bond0 by enslaving eth0 and eth1 to it. I added the below two entries to /etc/modprobe.conf. alias bond0 bonding options bond0 mode=6,miimon=100 Content of /etc/sysconfig/network-scripts/ifcfg-eth0 DEVICE=eth0 USERCTL=no ONBOOT=yes MASTER=bond0 SLAVE=yes BOOTPROTO=none Content of /etc/sysconfig/network-scripts/ifcfg-eth1 DEVICE=eth1 USERCTL=no ONBOOT=yes MASTER=bond0 SLAVE=yes BOOTPROTO=none Content of /etc/sysconfig/network-scripts/ifcfg-bond0 DEVICE=bond0 IPADDR= NETMASK= ONBOOT=yes BOOTPROTO=static USERCTL=no Did "modprobe bond0" and "service network restart" after that. 3 - Edit /etc/xen/xend-config.sxp Change (network-script network-bridge) To (network-script 'network-bridge netdev=bond0') 4 - Start xend. "service xend start". 5 - chkconfig xend on. 6 - modprode bond0 7 - more /proc/net/bonding/bond0 8 - Create guest images as usual and bridge it to xenbr0. about config i did for my xen kernel rhel 5.3 after i reboot the host server i get in place bond0 get pbond0 and its get disconnect from network only i ping to my vm's on the host server any one have any idea why xen bond0 is acting like that or what is solutions to come out of pbond0 to bond0.

  Read the article

• Broken filesystem on Windows XP / 7 virtual machine

  - by Pekka

  I created a virtual machine with Windows XP as the guest system in Microsoft's Virtual PC that ships along with Windows 7. I then installed Virtualbox and began running the MS machine in it. It worked fine. Then, I accidentally started the machine in Microsoft's Virtual PC again. The screen stayed blank, so after a while, realizing my mistake, I closed the Machine. Since then, the VM won't start any more, claiming massive file system problems. Starting Windows in normal mode results in a SOMETHING_FILESYSTEM blue screen; I can start in protected mode and run a checkdisk. That will fix something on every run, but every time I restart, it will start again. I tried re-booting the VM with the Windows CD and doing a repair install. I didn't watch whether that worked out, but I'm caught in the reset / check disk / reset cycle again. Is there anything VM specific that can still be done? On a physical machine, I would say reformat. Is there any way to get hold of the data on the virtual machine through either Virtual PC or Virtualbox? It was an experimental machine, but I had started entering some data on it that would be nice to recover.

  Read the article

• django : nginx : jquery css not being served

  - by PlanetUnknown

  I'm using apache+mod_wsgi for django. And all css/js/images are served through nginx. For some odd, reason when others/friends/colleagues try accessing the site, jquery/css is not getting loaded for them, hence the page looks jumbled up. My html files use code like this - <link rel="stylesheet" type="text/css" href="http://x.x.x.x:8000/css/custom.css"/> <script type="text/javascript" src="http://1x.x.x.x:8000/js/custom.js"></script> My nginx configuration in sites-available is like this - server { listen 8000; server_name localhost; access_log /var/log/nginx/aa8000.access.log; error_log /var/log/nginx/aa8000.error.log; location / { index index.html index.htm; } location /static/ { autoindex on; root /opt/aa/webroot/; } } There is a directory /opt/aa/webroot/static/ which have corresponding css & js directories. The odd thing is that the pages show fine when I access them. I have cleared my cache/etc, but the page loads fine for me, from various browsers. Also, I don't see any 404 any error in the nginx log files. Actually the logs for nginx are not getting refreshed at all. I restarted the nginx server using root, is that incorrect ? There is a user www-data defined in the nginx configuration file. Any pointers would be great.

  Read the article

• Will these instructions work when turning of journaling on a n ext4 SSD?

  - by snowlord

  I have an Acer Aspire One with an SSD for storage. I recently installed Ubuntu on it and chose ext4 for my filesystem. Then I read that journaling on an SSD isn't the best idea, so I will try to disable journaling and I have found these intstructions (from http://fenidik.blogspot.com/2010/03/ext4-disable-journal.html): # Create ext4 fs on /dev/sda10 disk mkfs.ext4 /dev/sda10 # Enable writeback mode. This mode will typically provide the best ext4 performance. tune2fs -o journal_data_writeback /dev/sda10 # Delete has_journal option tune2fs -O ^has_journal /dev/sda10 # Required fsck e2fsck -f /dev/sda10 # Check fs options dumpe2fs /dev/sda10 |more For more performance add fstab opions: data=writeback,noatime,nodiratime i.e: /dev/sda10 /opt ext4 defaults,data=writeback,noatime,nodiratime 0 0 I will use them on my boot partition. Are there any particularly bad parts here, or are there any missing steps? Will my boot partition be fit for being on an SSD after this? Or should I consider switching to ext2, or even reinstall it all and choose ext2 at partitioning time (I'd rather not though, since I've configured quite some stuff already)?

  Read the article

• HP G61 Laptop wont boot- display stays off, caps and num lock indicators blink repeatedly

  - by Benguy12

  I had my HP G61 laptop running in sleep for a while. When I came back to it about a half-hour later, it was no longer in sleep mode - the power light and the Wi-Fi indicator light were on (I keep Wi-Fi off becuase I use a wired connection) - but nothing was showing on screen. In fact, the display wasn't even turned on. So I let it sit for about 10 minutes but nothing happened. I did a force shut down and rebooted. Instead of a normal boot, the display didnt turn on, the Wi-Fi indicator was off, and the Caps Lock and Num Lock lights just blinked repeatedly. On the external keyboard i use, none of the light indicators were blinking or even on. I tried force shut-down again 10 times, then unplugged all connections except for the power cable (my laptop battery dosent hold a charge for more than 2 minutes, so I always must have a wall connection) and tried to boot again but still nothing happened. I unplugged the battery and even then nothing happened. I also tried booting with the disk drive open, and then with it closed again. On the time it was closed, I was able to successfully boot into Windows, but recieved a "Windows did not shut-down sucessfully" notice. Does anybody know why this may have happened? My PC's specs: Windows 7 Home Premium, 64-bit 4GB of physical RAM, 8GB of vRAM (on a flash drive) AMD Vision x64 processor (don't know any other specs about it) ATI Radeon graphics card, 392 MB DVD-R/W lightscribe drive 2 External hard-disks (first one is 1.5TB, second one is 1TB) custom boot-screen and boot-annimation Standard BIOS apps running before sleep: firefox 10.4 itunes 10.6 adobe photoshop extended CS5.1 rockstar games social club (running in background) microsoft powerpoint 2010 professional edition google chrome I was NOT running Aero or any fancy themes - I was using the normal windows classic theme. I have a desktop icon manager application called Stardock Fences that was also running (it runs as a service/process).

  Read the article

• Very long (>300s) request processing time on Apache Server serving static content from particular IP

  - by Ron Bieber

  We are running an Apache 2.2 server for a very large web site. Over the past few months we have been having some users reporting slow response times, while others (including our resources, both on the internal network and our home networks) do not see any degradation in performance. After a ton of investigation, we finally found a "Deny from none" statement in our configuration that was causing reverse DNS lookups (which were timing out) that solved the bulk of our issues, but we still have some customers that we are seeing in the Apache logs (using %D in the log format) with request processing times of 300s for images, css, javascript and other static content. We've checked all Deny / Allow statements for reoccurrence of "none", as well as all other things we know of that would cause reverse DNS lookups (such as using "REMOTE_HOST" in rewrite rules, using %a instead of %h in our log format configuration) as well as verified that HostnameLookups is set to "Off". As an aside, we've also validated that reverse DNS lookups for folks having this problem do not time out - so I'm fairly certain DNS is not an issue in this case. I've run out of ideas. Are there any Apache configuration scenarios that someone can point me to that I might be missing that would cause request times for static content to take so long only for certain users? Thank you in advance.

  Read the article

• Scriptable BitTorrent clients?

  - by James McMahon

  In an effort further automate all the little computer house keeping tasks that can waste my time I am looking into BitTorrent clients that have the ability to script common tasks. I've done some Googling and it looks like Transmission might have some of said such capabilities, but there site wasn't very clear on the details. Things I am looking to do; Prioritize and label torrents based on trackers Set seed length based on trackers and filesize Set additional seed time when a torrent's seed time expires based on a number of factors, like time spent seeding, remaining disk space and ratio. Move torrents to appropriate places post seeding based on labels and tracker Basically, while I could Python or Bash script things like moving torrents around and other simple actions, I need away to talk to the client to figure out things like the torrent seed time, tracker, labels, filesize, etc. Is there any client out there that would allow me to all or a subset these actions? I have access to Linux, Mac and Windows and am not tied to any particular torrent client. I am a programmer so I have no problems writing scripts, but examples of torrent scripting would also be helpful.

  Read the article

• Why does this preseed for gitolite fail?

  - by troutwine

  I'm installing gitolite on a Debian Squeeze box with the following preseed: gitolite gitolite/gituser string git gitolite gitolite/adminkey string ssh-rsa AAAAB3ECT gitolite gitolite/gitdir string /var/lib/git On installation: # debconf-set-selections /var/cache/debconf/gitolite.preseed # apt-get install gitolite Reading package lists... Done Building dependency tree Reading state information... Done Suggested packages: git-daemon-run gitweb The following NEW packages will be installed: gitolite 0 upgraded, 1 newly installed, 0 to remove and 26 not upgraded. Need to get 0 B/114 kB of archives. After this operation, 348 kB of additional disk space will be used. Preconfiguring packages ... Selecting previously deselected package gitolite. (Reading database ... 24715 files and directories currently installed.) Unpacking gitolite (from .../gitolite_1.5.4-2+squeeze1_all.deb) ... Setting up gitolite (1.5.4-2+squeeze1) ... adduser: The home dir must be an absolute path. dpkg: error processing gitolite (--configure): subprocess installed post-installation script returned error exit status 1 configured to not write apport reports Errors were encountered while processing: gitolite E: Sub-process /usr/bin/dpkg returned an error code (1) Why? The pre-seed was extracted from a manually configured installation, per here and exists without issue on another machine.

  Read the article

• Cloudfront - How to invalidate objects in a distribution that was transformed from secured to public?

  - by Gil

  The setting I have an Amazon Cloudfront distribution that was originally set as secured. Objects in this distribution required a URL signing. For example, a valid URL used to be of the following format: https://d1stsppuecoabc.cloudfront.net/images/TheImage.jpg?Expires=1413119282&Signature=NLLRTVVmzyTEzhm-ugpRymi~nM2v97vxoZV5K9sCd4d7~PhgWINoTUVBElkWehIWqLMIAq0S2HWU9ak5XIwNN9B57mwWlsuOleB~XBN1A-5kzwLr7pSM5UzGn4zn6GRiH-qb2zEoE2Fz9MnD9Zc5nMoh2XXwawMvWG7EYInK1m~X9LXfDvNaOO5iY7xY4HyIS-Q~xYHWUnt0TgcHJ8cE9xrSiwP1qX3B8lEUtMkvVbyLw__&Key-Pair-Id=APKAI7F5R77FFNFWGABC The distribution points to an S3 bucket that also used to be secured (it only allowed access through the cloudfront). What happened At some point, the URL singing expired and would return a 403. Since we no longer need to keep the same security level, I recently changed the setting of the cloudfront distribution and of the S3 bucket it is pointing to, both to be public. I then tried to invalidate objects in this distribution. Invalidation did not throw any errors, however the invalidation did not seem to succeed. Requests to the same cloudfront URL (with or without the query string) still return 403. The response header looks like: HTTP/1.1 403 Forbidden Server: CloudFront Date: Mon, 18 Aug 2014 15:16:08 GMT Content-Type: text/xml Content-Length: 110 Connection: keep-alive X-Cache: Error from cloudfront Via: 1.1 3abf650c7bf73e47515000bddf3f04a0.cloudfront.net (CloudFront) X-Amz-Cf-Id: j1CszSXz0DO-IxFvHWyqkDSdO462LwkfLY0muRDrULU7zT_W4HuZ2B== Things I tried I tried to set another cloudfront distribution that points to the same S3 as origin server. Requests to the same object in the new distribution were successful. The question Did anyone encounter the same situation where a cloudfront URL that returns 403 cannot be invalidated? Is there any reason why wouldn't the object get invalidated? Thanks for your help!

  Read the article

• Error during Time Machine backups on OS X Lion

  - by user92401

  After I turn on my machine, the first couple of Time Machine backups seem to go OK, but after about an hour I get this error: Unable to complete backup. An error occurred while creating the backup folder. Latest successful backup: 7/31/11 at 12:32 PM I'm running 10.7. Time Machine is backing up an internal HD to an external USB HD. I've already run Disk Utility to repair the Time Machine partition. It's a relatively new hard drive and didn't have any issues. Here's what I've found in the Console's log filtered for backupd: 7/31/11 12:31:21.223 PM com.apple.backupd: Starting standard backup 7/31/11 12:31:21.447 PM com.apple.backupd: Backing up to: /Volumes/MyMac TM Backup/Backups.backupdb 7/31/11 12:31:29.146 PM com.apple.backupd: 983.7 MB required (including padding), 391.90 GB available 7/31/11 12:32:19.471 PM com.apple.backupd: Copied 3156 files (36.0 MB) from volume Macintosh HD. 7/31/11 12:32:20.017 PM com.apple.backupd: Copied 3173 files (36.0 MB) from volume LI. 7/31/11 12:32:20.136 PM com.apple.backupd: 934.8 MB required (including padding), 391.86 GB available 7/31/11 12:32:54.755 PM com.apple.backupd: Copied 916 files (117.8 MB) from volume Macintosh HD. 7/31/11 12:32:54.894 PM com.apple.backupd: Copied 933 files (117.8 MB) from volume LI. 7/31/11 12:32:55.937 PM com.apple.backupd: Starting post-backup thinning 7/31/11 12:32:55.937 PM com.apple.backupd: No post-back up thinning needed: no expired backups exist 7/31/11 12:32:55.960 PM com.apple.backupd: Backup completed successfully. 7/31/11 1:21:28.624 PM com.apple.backupd: Starting standard backup 7/31/11 1:21:28.631 PM com.apple.backupd: Backing up to: /Volumes/MyMac TM Backup/Backups.backupdb 7/31/11 1:21:28.682 PM com.apple.backupd: Error: (22) setxattr for key:com.apple.backupd.HostUUID path:/Volumes/MyMac TM Backup/Backups.backupdb/Will’s Mac Pro size:37 7/31/11 1:21:28.683 PM com.apple.backupd: Error: (22) setxattr for key:com.apple.backupd.HostUUID path:/Volumes/MyMac TM Backup/Backups.backupdb/Will’s Mac Pro size:37 7/31/11 1:21:38.694 PM com.apple.backupd: Backup failed with error: 2

  Read the article

• Collect temperature and fan speed with munin from Windows 7 PC?

  - by mfn

  Hi, I'm quite fond of munin and using it also at home to monitor my PCs. What was super-duper easy under Linux is pretty much unsolvable for me under Windows: I'd like to monitor CPU and Motherboard temperatures as well as fan speed. On Linux I'm using lm-sensors and the plugin for munin was basically there. I access already some information from my Windows machine via SNMP (disk space, CPU usage, memory usage); the graphs are simple as is the information exposed via SNMP, but they do their job. But when it comes to temperature and fan speed I'm running against a wall. My research so far resulted in that Windows does not by default provide out of the box ability to retrieve temperature/fan speed data. Third party applications are necessary which have know-how how to communicate with the Motherboard chips. The best I cam up with is that SpeedFan exposes a shared memory interface and there exists a library which hooks into Windows SNMP facility and bridges over to SpeedFans shared memory interface; it's called SFSNMP (site currently down). Unfortunately the library doesn't work, there's a bug report at SpeedFan open about it, but it's currently not moving (although the SFSNMP author is active there) . So, unless that's going to work like anytime soon, are there any alternatives? I'm not found of buying any software to get that feature, given that I take it as granted that my system exposes me the information to properly monitor it, but anyway don't just not answer because of this.

  Read the article

• Diagnosing Microsoft SQL Server error 9001: The log for the database is not available.

  - by Scott Mitchell

  Over the weekend a website I run stopped functioning, recording the following error in the Event Viewer each time a request is made to the website: Event ID: 9001 The log for database 'database name' is not available. Check the event log for related error messages. Resolve any errors and restart the database. The website is hosted on a dedicated server, so I am able to RDP into the server and poke around. The LDF file for the database exists in the C:\Program Files\Microsoft SQL Server\MSSQL10.MSSQLSERVER\MSSQL\DATA folder, but attempting to do any work with the database from Management Studio results in a dialog box reporting the same error - 9001: The log for database is not available... This is the first time I've received this error, and I've been hosting this site (and others) on this dedicated web server for over two years now. It is my understanding that this error indicates a corrupt log file. I was able to get the website back online by Detaching the database and then restoring a backup from a couple days ago, but my concern is that this error is indicative of a more sinister problem, namely a hard drive failure. I emailed support at the web hosting company and this was their reply: There doesn't appear to be any other indications of the cause in the Event Log, so it's possible that the log was corrupted. Currently the memory's resources is at 87%, which also may have an impact but is unlikely. Can the log just "become corrupted?" My question: What are the next steps I should take to diagnose this problem? How can I determine if this is, indeed, a hardware problem? And if it is, are there any options beyond replacing the disk? Thanks

  Read the article

• how to back up data from a machine that keeps hanging

  - by Amit Phatarphekar

  Hello - I have a storage server running opensolaris. But lately its been acting up - it hangs at random times due to some SCSI/ATA related error messages. I've tried to fix it without any progress, so I'm giving up now. The machine keeps hanging every 30 minutes or 1 hr ...sometimes after 4 hrs. Its very unpredictable. So I've decided to just reformat the storage server and start from scratch...maybe I'll just not use solaris and install something else, since the errors are related to solaris running on ATA HDD or something. Question - Before I reformat it, I want to back up some of the important data on it. Like it has a VM with 200 GB disk files, it has a whole bunch of ISOs stored on it etc etc. I'm using a simple scp to copy the files over to a different machine. My issue is that, because the machine hangs....sometimes my file copy is incomplete and I have to start all over again. Lets say I'm trying to copy a 200GB file which takes like 4 hrs....IF the machine hangs before the whole file i copied over...I have to recopy the file from scratch. Is there a solution to copy the files over such that if the machine hangs or network goes down..the copying can resume from where it left off? - like if 50 GB of a 200GB file was copied and machine hung....next time, it'll just continue to copy rest of the amount, instead of starting all over again. Thanks Amit

  Read the article

• Browser says "Waiting for www.xyz.com" for a very long time

  - by Phil

  When I load my website (hosted with Ipage). The browser often takes an incredible long time saying "Waiting for www.xyz.com ..." before any elements of the site actually appear. After this "Waiting for" process, the text, images and everything else actually load quite fast. I contacted my host with my tracert result and they said they optimized my website database and increased the memory available to PHP on my account to 64 Mb.They also said they have checked the issue by accessing my website and found that it is loading fine without any slowness. It seems to be a temporary issue. Please try to access your website with different browser and network. I tried different browsers and networks but this "Waiting for" process always takes too long. My website is http://www.surreyextra.com/ . It's Wordpress and BuddyPress. I'm in the UK while Ipage host is placed in the USA, can this potentially be a problem? I have tried a number of optimizations, like minifying my CSS and JS files and use catching but the problem hasn't improved. So is it my host's fault, should I contact them again?

  Read the article

• Malware Defense Shows Up in PlayOn Settings/Logs Although System Has Been Thoroughly Cleaned

  - by nicorellius

  I was hit really hard by some nasty malware: Malware Defense. I was doing something I should not have been doing when I got it (surfing Pirate Bay for TV shows). It locked up my system and I had to reboot in safe mode. I was able to shut down the process and remove it using a malware killer tool. I then installed, after my machine was cleaned up a bit, Clamwin, Malwarebytes, and another AV tool. I cleaned the heck out of my system. Simultaneously, while this was going on, I was having trouble with my media-server, PlayOn. This tool is great, but has some bugs. One in particular is that it will not function well with AV software running. I found a way to allow the new AV software to run while using PlayOn, but it still says I have Malware Defense on. Firstly, Malware Defense is long gone. I cleaned all remnants from my registry and scoured my system with the above tools multiple times. PlayOn is getting some information that I have this crap installed on my system, but it's not. The system runs OK, but not optimally. I have a feeling it is causing my streaming to be interrupted sometimes. How is it that I can't even find Malware Defense on my system if I tried but yet somehow PlayOn is getting a finger print of it somewhere? I have gone back and forth with MediaMall to no avail. I kind of just gave up, because the streaming works OK. BTW, I also uninstalled/reinstalled PlayOn several times, reverted back to previous versions, etc. The only thing I haven't done is reformat my disk and reinstall Windows. I really don't want to do this if there is another way to remove this little print. Any ideas?

  Read the article

• Sony PMB causing failure to load Windows 7 Pro 64-bit normally or even Safe Mode

  - by Wesley

  After installing Sony's Picture Motion Browser on my desktop with Windows 7 Pro x64, it always goes to Startup Repair due to Windows 7 failing to start. This always happens after I try to install it. I've installed with all unnecessary programs closed and all disk drives and unnecessary usb ports empty. I don't exactly know what is causing the problem. Any ideas? My desktop is an HP m8530f. http://h10025.www1.hp.com/ewfrf/wc/document?docname=c01469325&tmp_task=prodinfoCategory&lc=en&dlc=en&cc=us&product=3740333&lang=en Only upgrades are an HD4350 and a 500W PSU. EDIT: Windows 7 cannot start now. I'm currently running diagnostic tests from the BIOS. EDIT: Here are the problem details. Problem Signature: Problem Event Name: StartupRepairOffline Problem Signature 01: 6.1.7600.16385 Problem Signature 02: 6.1.7600.16385 Problem Signature 03: unknown Problem Signature 04: 21201022 Problem Signature 05: AutoFailover Problem Signature 06: 8 Problem Signature 07: CorruptFile OS Version: 6.1.7600.2.0.0.256.1 Local ID: 1033 CONCLUSION: So, I think Sony PMB may have caused some sort of corruption in the system files. So if you have Windows 7 and plan on installing Sony PMB, find a Vista or XP machine to install on.

  Read the article

• 13" MacBook Pro with Win 7 and External VGA gets 640x480

  - by Jim McKeeth

  I have a brand new 13" MacBook Pro - 2.26 GHz and the NVIDIA 9400M Video card. I installed Windows 7 (final) in boot camp and booted up to Windows 7. Installed all the drivers from the Apple disk and it was working great. Then I attached the external VGA adapter (from apple) to connect to a projector and it dropped down at 640x480 resolution. No matter what I did it wouldn't let me change to a higher resolution if the external VGA was connected. Once it disconnects then it goes back to the normal resolution. If I am booted into Snow Leopard it works fine. I tried updating the NVIDIA drivers and it behaved exactly the same. Ultimately I want to get 1024x768 or better resolution when connected to an external display. If it isn't fixable then I am curious if anyone else has seen this, if it is a known issue, and who to contact for support (Apple, Microsoft or NVIDIA?) Update: Just attaching the Mini-DVI to VGA adapter kicks it into 640x480, no projector is required. I tried forcing the display driver from Generic PnP Monitor to one that supported 1024x768 and that didn't work either.

  Read the article

• Using Toshiba 22EL833 as PC display with GTX8800

  - by Oleg V. Volkov

  I had another Toshiba TV - 19SL738 - connected to this same PC and video card (GTX 8800) through DVI<-HDMI (DVI on PC side, HDMI on TV) before, that was working perfectly at it's native resolution 1360x768. Some time ago I had to change to 22EL833 and immediately faced problem with Windows 7 control panel and NVIDIA control panel both reporting native resolution for new TV as 1080i, 1920x1280, despite TV documentation saying that it have same 1360x768 as previous one. Practical tests confirmed that true native resolution is indeed 1360x768, because plugging in through DVI<-VGA and setting custom resolution through NVIDIA panel shown clear colors and crisp image, while setting anything different with either DVI<-VGA or DVI<-HDMI produced horribly distorted or squished images, with almost unreadable slim lines (as in letters, for example). Now, my problem is that there's no drivers for this TV and I'm unable to get good image while connecting it through DVI<-HDMI directly. The best I've achieved is editing EDID/driver manually, to persuade system that native resolution should be 1360x768, and while image became mostly clear, colors turned to some strange washed out effect, with pools of pure yellow, cyan and magenta there and there filling place of other colors. Gradients also became noticeably stripped as well. Somehow it looks like dithering gone bad and makes me suspect that image is still down/upscaled several times internally somewhere along the line. How can I connect this TV to DVI output of my video card to get best possible clear image, correct colors and correct native resolution?

  Read the article

• Stop the constant random reboots of my GIGABYTE GA-B75M-D3V

  - by Frederic

  I've got some issues with a new system. It's rebooting constantly. The system consists of a: brand new: Gigabyte GA-B75M-D3V with F9 BIOS (latest) Intel Core i5-3470 Ivy Bridge 2x 8GB G.SKILL Ripjaws 1600MHz memory (mem-tested x-86) coming from a stable system: Creative Soundcard X-FI Titanium Asus Radeon HD4850 OCZ Vertex 3 120G SSD Sata 3 Hard disk 1TB Sata 2 ASUS Blu-ray Drive PSU 400w Connected peripherals : Toshiba tv (displayport on dvi of MB or HD4850) Wired mouse, wireless keyboard (logitech) Bluetooth usb key Azio main problem : it's not possible to read the errors from the MB. nothing on the manual neither on internet. At the beginning, I received a MB with graphic problems and the problem of rebooting. I RMA'd it. The new one doesn't have any graphic problems. but it's still constantly rebooting. I removed everything except the HD, the sound-card, the blu-ray drive and the wireless keyboard. It's still unexpectdly rebooting. I'm running a test with just the motherboard and the HD. I will update this text after the test. I've got some questions : Somebody have an idea of a test? The PSU could cause that problem? I used it a lot of years with the stable system. Update 1: BTW, if anyone has the same problem, the manual won't say it but you'll need to reset the bios between two tests (the screwdriver on the two pins) if you suspect a problem of compatibility .

  Read the article

• CentOS vps is randomly rebooting

  - by develroot

  I have a centos vps (Parallels Virtuozzo container) which has been running for months. However, a few days ago it started to randomly reboot itself, and i can't find out why. And the biggest problem that i don't understand is that it takes 40 minutes to reboot (as far as i can see in the logs) root ~ # cat /var/log/messages | grep shutdown Oct 11 13:52:11 vps27 shutdown[23968]: shutting down for system halt Oct 14 14:55:17 vps27 shutdown[30662]: shutting down for system halt Oct 15 06:21:23 vps27 shutdown[20157]: shutting down for system halt And notice the time difference between shutdown and xinetd's start: Oct 15 06:21:23 vps27 shutdown[20157]: shutting down for system halt Oct 15 06:21:24 vps27 init: Switching to runlevel: 0 Oct 15 06:21:27 vps27 saslauthd[30614]: server_exit : master exited: 30614 Oct 15 06:21:38 vps27 named[30661]: shutting down Oct 15 06:21:47 vps27 exiting on signal 15 Oct 15 07:04:34 vps27 syslogd 1.4.1: restart. Oct 15 07:05:06 vps27 xinetd[1471]: xinetd Version 2.3.14 started with libwrap loadavg labeled-networking options compiled in. Oct 15 07:05:06 vps27 xinetd[1471]: Started working: 0 available services And here's what Parallels Power Panel says in terms of Status Changes: Time Old Status Status Obtained Oct 15, 2011 06:23:46 AM Mounted Down Oct 15, 2011 06:22:31 AM Running Mounted Oct 14, 2011 03:06:48 PM Starting Running Oct 14, 2011 03:06:23 PM Down Starting Oct 14, 2011 03:06:08 PM Mounted Down Oct 14, 2011 02:58:24 PM Running Mounted For some reason it's getting into Mounting mode and then restarts itself. The only problem that i can imagine is disk space utilization, which is now 84%. But can that be a reson for system halt? Time Category Details Type Parameter Oct 15, 2011 07:08:33 AM Resource Resource counter_disk_share_used yellow alert on environment vps27 current value: 82 soft limit: 85 hard limit: 95 Yellow zone counter_disk_share_used Oct 15, 2011 06:27:23 AM Resource Resource counter_disk_share_used yellow alert on environment vps27 current value: 82 soft limit: 85 hard limit: 95 Yellow zone counter_disk_share_used Oct 15, 2011 06:23:50 AM Resource Resource counter_disk_share_used green alert on environment vps27 current value: 0 soft limit: hard limit: 0 Green zone counter_disk_share_used Oct 14, 2011 03:06:24 PM Resource Resource counter_disk_share_used yellow alert on environment vps27 current value: 83 soft limit: 85 hard limit: 95 Yellow zone counter_disk_share_used Oct 14, 2011 03:05:50 PM Resource Resource counter_disk_share_used green alert on environment vps27 current value: 0 soft limit: hard limit: 0 Green zone counter_disk_share_used

  Read the article

• Excluding files from web logs

  - by Ray

  I originally tried this question on StackOverflow, but it was suggested that serverfault was a better choice. So, here it is... Looking through my web logs, I see a lot of entries that don't interest me. Some of them are commonly used images, css files, and scripts, which I can easily exclude by un-checking the 'log visits' check box in IIS for the folder properties. I would also like to exclude log entries for certain common requests which are not in their own folders. Mostly, 'favicon.ico'. 'scriptresource.axd', and 'webresource.axd'. These (especially scriptresource.axd) make up almost a third of a typical log file on my site. So, the question is, how do I tell IIS not to log these requests? And is there any reason that this is a bad idea? The purpose of doing this is to reduce the log file size and the amount of work the server has to do, to make the log file more manageable when I need to dig in to them for troubleshooting, and for my own curiosity. I realize that log file parsers can skip the junk, but I am interested in reducing the raw files, before parsing.

  Read the article

• How can I take a one time full backup of a Windows Server without the need for a restore program?

  - by TheCleaner

  I have a Windows SBS server with about 500GB of data that I'm decommissioning but I'd like to take a final backup of the server and place it on an external USB drive. I already have multiple backups of the server on disk from the past but they are through Simpana Commvault. I'd like a backup that will simply copy the file structure, ACLs, timestamps, etc. as is to a NTFS volume on the external drive. This way if someone says "I need x file on the server you decommed" I can search the external drive real quick instead of firing up Commvault, cataloging, restore, etc. I know the built-in Windows backup is great, I just don't feel like running it for a restore job on this. I'd like an option where in the future it won't require a program to run a restore. Rather a simple mount of the drive will suffice. I believe I can use robocopy just fine, but I'm not sure if it will grab the Windows directory, system files, and full user profiles correctly even with the /ZB option. Options? Is Robocopy /E /ZB /COPYALL /DCOPY:DAT /MT:32 /R:5 /W:5 /LOG:copylog.log the way to go here?

  Read the article

• Why is my mono/XSP site loading slow?

  - by acidzombie24

  I have two sites on the same server. One is loading perfectly and incredibly fast. The other is an equally complex site except a bit less javascript and 0 images. Its taking several seconds to load and there is a 1 in 3 chance that i get a Http500 error. WTF I grabbed the lastest 2.6.? version of mono, mod_mono and xsp (libgdiplus-2.6.7, xsp-2.6.5, mod_mono-2.6.3 and mono 2.6.7) This is whats in apache error.log [Mon Jan 03 19:33:40 2011] [error] (70014)End of file found: read_data failed [Mon Jan 03 19:33:40 2011] [error] Command stream corrupted, last command was 1 [Mon Jan 03 19:34:52 2011] [error] (70014)End of file found: read_data failed [Mon Jan 03 19:34:52 2011] [error] (70014)End of file found: read_data failed [Mon Jan 03 19:34:52 2011] [error] Command stream corrupted, last command was 1 [Mon Jan 03 19:34:52 2011] [error] Command stream corrupted, last command was 1 this is the page error Internal Server Error The server encountered an internal error or misconfiguration and was unable to complete your request. Please contact the server administrator, webmaster@localhost and inform them of the time the error occurred, and anything you might have done that may have caused the error. More information about this error may be available in the server error log. Apache/2.2.9 (Debian) PHP/5.2.6-1+lenny9 with Suhosin-Patch mod_mono/2.6.3 Server

  Read the article

• Virtual Windows 2008 Server Activation with ESX

  - by Logman

  I had a decommissioned server (Dell PE2950) that we could still use, it had OEM Windows 2003 Std on it but wanted to use it as a new host with VMware ESX5 to put a couple legacy severs on it. I wiped it clean and maxed out the memory. But when I added the memory I noticed the product key sticker was a "WindowsServer08 Std 1-4cpu" product key, and it also had a Virtual Key. Not sure why it had Win2003 and not Win2008 from the start, but I would like to use that license if I can. The virtual host would stay on the same physical server, so there shouldn't be a problem with licensing... but I do not want to use Hyper-V unless I can not help it. I have installed ESX5 on the server, but I cannot get the Windows 2008 server to activate. The product key is hard to read, and I have checked the key quite a few times. But my question is... Is it because Hyper-V was not installed on the host? But I thought you could use the product key alone on a virtual host? Maybe because I am not using a Dell Windows 2008 disk but iso from MS directly via the Volumne Licensing site? EDIT: well, Im pretty sure I got the product key correct. If its not the product key, could the activation problem be because Im not using hyper-v or maybe the correct install dvd? EDIT2: maybe because I added 28GB of memory? Originally 4GB...

  Read the article

• Windows 7 pc freezes for an indeterminate amount of time after unlocking

  - by pikes

  Not sure if this type of question is appropriate for this forum, but I've tried everything I can think of to solve this problem aside from format/reinstall. I recently got a new work PC (Dell optiplex 755) with windows 7 professional x64. Standard developer software installed for .net development: VS2008, VS2005, SQL management studio, office 2007, etc. Recently I've been having this weird problem where after I lock my pc, when I try to unlock it, the screen will be black for awhile after unlocking. I can ctl+alt+del and put my password in but then it just goes black. The amount of time on the black screen seems to be related to the amount of time I am away from my PC. If only away a few minutes, it'll take about a minute to get to the desktop. If away for an hour, could take up to 15 minutes. If I lock it and go home for the night, I have to restart my PC in the morning (I've let it sit for an hour after a night of being locked and nothing happened). It doesn't do it every time but definitely the majority of the time. One weird thing I've seen is that if I remote into my machine before trying to log back in it does not do it. I uninstalled all software back to the point when I remember it started happening and it still does it. I was using this PC for a few weeks without this problem happening at all. Anyone know what my next troubleshooting steps could be? My IT department tried to fix it by moving my old profile to another disk and having me log in, effectively recreating a profile from scratch but that didn't solve it. As I said above if this isn't the right forum for these types of questions please let me know. Thanks in advance!

  Read the article

< Previous Page | 655 656 657 658 659 660 661 662 663 664 665 666  | Next Page >