Search Results

Search found 17267 results on 691 pages for 'home router'.

Page 66/691 | < Previous Page | 62 63 64 65 66 67 68 69 70 71 72 73  | Next Page >

• Using QoS to prioritize IP addresses

  - by Tristan

  I have a Western Digital N900 router. I was hoping I'd be able to throttle users based on their MAC address with it, which isn't possible sadly. Seems simple in principle though, duh. The battle against bandwidth hogging roomates rages on. Could I just set the local IP range to their IP, and then set the Local port range to every single port in existence. Then prioritize their IP to lower than mine? Will this work? What are all the ports? And what's the difference between Local and Remote IPs or Ports? Name: Roomate, Priority: Low, Protocol: TCP or UDP ??, Local IP Range: .101 to .101, Local Port Range: 0 to infinity, Remote IP Range: ? to ?, Remote Port Range: ? to ?

  Read the article

• Anytime I upload something, my internet slows down extremely. What can I do?

  - by Earlz

  Title says it all. For a bit more info though: Basically, I have Time Warner cable internet. My speeds maintain a stable 2Mbit/s upload and 20Mbit/s download with average ping times around 30ms. This crazy thing happens though when I upload anything. I went to upload a 200M file to my server today through sftp and my internet completely choked up. I speed tested it during this upload and my ping time was around 800ms, download speeds of 0.2Mbit/s and Upload speeds of 0.3Mbit/s. Note, I wasn't downloading anything during this time either. It is just straight upload. What is it that causes this phenomenon? My router is OpenBSD. Is there anything I could set up to fix this problem(by queues or some such), or is this a problem with cable internet?

  Read the article

• DIR 601 No wireless internet

  - by ashley

  I have an orange globe on my d link router. I signed into 192.168.0.1 and went to Manuel Internet Connection Setup as I was told to do. When I clicked on that and tried to clone my PC's MAC address, it said invalid MAC address. Host Name : DIR-601 Use Unicasting : (compatibility for some DHCP Servers) Primary DNS Address : 0.0.0.0 Secondary DNS Address : 0.0.0.0 MTU : (bytes) MTU default = 1500 MAC Address : F8:1E:DF:EA:38:E6 How do I get a valid MAC address so I can save the settings and move on to the next steps I was told to do in order to get wireless internet again?

  Read the article

• Calculate data transferred in a local LAN

  - by ramdaz

  How do you calculate the data flown between a computer and the gateway computer. I have a Linux router/gateway running IP Tables which routes internet traffic in a LAN. I have individual users with IP/MAC Address mapped who access Interet through the gateway computer. I would like to find out the traffic utilized by individual users. Is it possible for us to find out what kind of traffic was HTTP, SMTP, FTP etc. Is it also possible to pool the information on hourly basis, and get specific info so that I can store information in a database? I have heard of IP Accounting? Is that the right way

  Read the article

• Ask The Readers: How Do You Camouflage Your Tech?

  - by Jason Fitzpatrick

  We love having a technology-packed house as much as the next geek, but not all our gizmos, gadgets, and peripherals are exactly Home and Garden approved. How do you enjoy all your tech without your living room and office looking like an electronics store? Image courtesy of Weekly Geek’s DIY charging station tutorial. Whether it’s to hide the insanely intense LEDS, minimize the visual clutter, or to boost the wife/husband acceptance factor of your geeky hobbies higher, there’s a variety of reasons for wrangling cables, hiding routers, or otherwise camouflaging your gear. This week we want to hear all about your tips for hiding or otherwise minimizing the appearance of gear around your home, office, and other personal spaces. Sound off in the comments with your best tips, trick, and camouflaging techniques; check back in on Friday for the What You Said roundup. HTG Explains: How Windows 8′s Secure Boot Feature Works & What It Means for Linux Hack Your Kindle for Easy Font Customization HTG Explains: What Is RSS and How Can I Benefit From Using It?

  Read the article

• How can I selectively increase latency? E.g. throttle games

  - by Arcymag

  Basically, I want networked games to run poorly on a network, but I want everything else to run smoothly. I would also appreciate advice on blocking games in general. As far as I can tell, there's a few ways to completely prevent an internet game from running: Blocking entirely via DNS configuration (e.g. hosts file), or router DNS configuration Blocking entirely via a separate DNS server Blocking the application, by uninstalling or some kind of access control Blocking the application by automatically killing the process every once in a while Blocking the application by corrupting files periodically However, I would like a more subtle way to block a program. Something that either: Increases latency (would this be doable through some kind of QoS like what DD-WRT offers?) Increases latency by using a special routing configuration for specific target IPs Throttle other systems resources, such as memory, IO, or CPU Screw around with keyboard configurations when a game is launched I would like this to work on MacOSX and Windows, but Linux would be great too. FYI I don't have a kid, but I was brainstorming with some friends and parents.

  Read the article

• Mysterious problem...can remotely connect to a system but can't browse back out.

  - by GregH

  I have LogMeIn installed on my home system. I went on travel and my wife called saying that none of our home systems could browse the internet. I thought I would try to connect to my home system using logmein. Surprisingly, I was able to connect to my home system and log in without any problems using logmein. When I opened a browser from my home system, I indeed could not browse. I opened a command prompt and tried to ping my router (192.168.1.1) and it failed/timed out. How is this possible? I can remotely connect to my system but once logged in cannot even ping my router. What's up with that?

  Read the article

• Tomato QoS: Why is some traffic unclassified when there are classifications for it?

  - by Armitage

  Ok, I am trying to tweak my router to give priority to some traffic. My classifications seem to cover just about everything but I still see ~60 to ~80% of the traffic as unclassified: TCP 192.168.1.100 64137 192.168.1.1 80 Unclassified TCP 192.168.1.100 64175 192.168.1.1 80 Unclassified TCP 192.168.1.100 64144 192.168.1.1 443 Unclassified I assume that the 64### ports are just what my WAP uses to send packets inside my home network. But my classifications seems to cover any traffic for destination ports 80 and 443: (partial list) TCP Dst Port: 80,443 High WWW TCP/UDP Dst Port: 1024-65535 Lowest Bulk Traffic Why do I have so much unclassified traffic if I have a classification that should cover it?

  Read the article

• Two internet connections coming in, one Sonicwall Tz170 (enhanced os), and slow speed

  - by Development 4.0

  I work a lot from my home office and being in general a tad paranoid I have cable and DSL pipes coming into my house. I have used an Ebay bought Sonicwall Tz170 with the enhanced OS for a good while. I believe it does failover and has a feature for doing round robin on which connection is used. I get the impression from using it that I might not be getting the most out of this setup. Is it possible/likely that my router could be a cause of the slowdown? Are there more appropriate choices?

  Read the article

• Does IP helper forward subnet broadcasts?

  - by Eamon

  Hi, I have a device on a VLAN that uses UDP subnet broadcasts to advertise its presence to similar devices. This works fine on a single VLAN, but now I need to allow it to communicate with similar devices on a second VLAN. I thought of using the IP helper command in the router, but I am wondering if that only forwards global broadcasts (255.255.255.255)? My device sends out a subnet broadcast (e.g. 192.168.6.255) Will IP helper change the destination address to the target subnet (e.g. 192.168.7.255)? Eamon

  Read the article

• Ip doesn't change when switching networks, although automatic ip is set. Cause of the issue known

  - by Julio Acevedo

  I have two routers at my house. Both of them have DCHP server enabled. One of them is 192.168.1.1 and gives adresses from 192.168.1.2 to 192.168.1.32 The other one is 192.168.1.50 and gives adresses from 192.168.1.51 to 192.168.1.99 The problem is that I only have internet access in one because my ip is 192.168.1.7, and when I switch to the other one, the ip remains 192.168.1.7, even though I have automatically get a ip adress in Ipv4. When I manually change my ip to one in the range allowed by the router, I can browse the internet. Any ideas how to solve this? Thank you.

  Read the article

• Why is the root partition on my disk full?

  - by Agmenor

  I installed Ubuntu 12.04 by doing a fresh install where there was previously Ubuntu 11.10. My computer warns me now that my disk is nearly full. After having run apt-get purge, run apt-get autoremove and emptied the Trash can, I still have this problem as shown by this screenshot of Gparted: The disk /dev/sda7 is indeed full. I ran the Disk Usage Analyzer (Baobab) and I am still not sure of what is happening: One of my hypothesis is that when installing Ubuntu 12.04, I didn't configure my disks well and the disk /dev/sda6 is not mounted well as /home. Is this the reason indeed? What should I do to verify this and then to get the things fixed? Here are a few additional details to answer the questions I received (thank you everybody): My home directory is not encrypted. The Backup utility (Déjà Dup) is not set for automatic backups. (I do it myself and manually.) After I mount /dev/sda6, the command df -h gives Filesystem Size Used Avail Use% Mounted on /dev/sda7 244G 221G 12G 96% / udev 3,9G 4,0K 3,9G 1% /dev tmpfs 1,6G 904K 1,6G 1% /run none 5,0M 0 5,0M 0% /run/lock none 3,9G 164K 3,9G 1% /run/shm /dev/sda6 653G 189G 433G 31% /media/8ec2fa69-039b-4c52-ab1b-034d785132a1 (sorry but formatting this into code does not work, for an unknown reason) Thanks to izx's post, I realized /dev/sda6 was not even mounted before. It contains all the documents I used to have when I was running Ubuntu 11.10.

  Read the article

• Multicast accross the subnets

  - by Hasan Khan

  My application sends some UDP packets on a multicast address. In our office we have 3 subnets connected via routers. Sitting in my subnet I'm able to ping the IP of the other subnet. Will multicast packets cross my subnet and reach the machines of other subnets? Or router will need some configuration? Or do I have to program a bridge for it? Please note that I do not know anything about Networking. Kindly tell me something that I can ask my network admin to do.

  Read the article

• Wireless is not currently enabled

  - by ikartik90

  I have a HP Pavilion TX2000 tablet PC with me with windows 7 OS running on it. I used to access the Internet using my D-Link DIR 615 wireless adapter on the tablet and it used to work quite fine until one day, when I hibernated my Windows 7, the wireless went off and the problem seems to persist even after my hard efforts to clear it. I checked if the router works fine, and yes it did as my iPod was still catching wireless signals on the other hand, when I checked mu device manager, I realized that I now had no wireless driver. I checked on HP's website for one, but ironically even they didn't have wireless drivers meant for my tablet for Windows 7. Please help me find a solution to this problem. Further queries will be entertained as frequently as possible. Thanks.

  Read the article

• SNMP counter issues with cisco RV082

  - by Chance

  Does anyone else poll this router with SNMP? We are using firmware version: 2.0.0.19-tz We are having problems with the traffic counters, some of them appear to be implemented as 16 bit counter instead of 32 bit counters. The reason this is causing problems is that they roll over (at 65,000) to 0 in less than our minute polling cycle, really skewing our metrics. The counter for the Lan (interface 2) seems to be functioning properly, however interfaces 3 and 4 (WAN and DMZ / WAN2) rollover at 65000. Tue May 11 08:38:31 EDT 2010 IF-MIB::ifInOctets.1 = Counter32: 137634 IF-MIB::ifInOctets.2 = Counter32: 1865677943 IF-MIB::ifInOctets.3 = Counter32: 12450 IF-MIB::ifInOctets.4 = Counter32: 49354 Look at counter IF-MIB::ifInOctets.4 5 seconds later: Tue May 11 08:38:36 EDT 2010 IF-MIB::ifInOctets.1 = Counter32: 137634 IF-MIB::ifInOctets.2 = Counter32: 1865836207 IF-MIB::ifInOctets.3 = Counter32: 13167 IF-MIB::ifInOctets.4 = Counter32: 12900 Any suggestions? Seems like a bug to me, however I just wanted to make sure I wasn't crazy.. Thanks!

  Read the article

• My internet connection just got really slow - How can I troubleshoot it?

  - by Walden

  A few days ago my connection became really slow. I have DSL which should be 3mb down and 768k up. I'm lucky if I get 768k down and 200k up. It sucks. I called my ISP, Verizon and they did some sort of line test and told me the problem was on my end. I rebooted my modem several times, like they told me. I'm not really sure why I even bothered calling them, the guy on the other end was just reading stuff out of a notebook - pretty useless. So, I checked my network traffic in windows resource monitor, and there doesn't seem to be anything there hogging the bandwidth. What else could be slowing my connection down on my PC? on my router? Something else?

  Read the article

• How to make a btrfs snapshot?

  - by MountainX

  My /home partition consists of an entire physical disk. It is formatted as btrfs. I want to snapshot it. I'm confused regarding subvolume naming, in particular. I am aware that there are similar questions, but each similar question seems to be asking something different from what I'm asking (and they are older, which means probably outdated, given the rapid development of btrfs). For example, the answer to this question is apparently not the answer to my question because my /home partition is a separate volume and the man page for btrfs shows a different command for creating snapshots now. another similar problem, no solid solution. someone else as confused as me on the naming issues My question: Starting simple: is this the correct command to take a simple snapshot of my home partition? btrfs subvolume snapshot /home/@home /home/@home_snapshot_20120421 I got really brave and tested it and it does not work. The error is error accessing /home/@home. As shown below, @home is listed. I'm obviously confused on subvolume names. Do I need to use them in creating snapshots? Some examples show taking snapshots of home using /home as the source parameter, but based on examples of root volumes, it seems to me that I need to use /home/@home. Would this command work? And if not, why? btrfs subvolume snapshot /home /home/@home_snapshot_20120421 Is the @ just a naming convention? Is it meaningful at all? Here's some output that may be relevant: btrfs subvolume list /home ID 256 top level 5 path @home I'm not sure what that means, exactly. When I try btrfs device scan it gives an error (e.g. unable to scan the device /dev/sda1). My file system doesn't have any errors. Everything is fine.

  Read the article

• Encrypt LAN and wifi traffic on small private network

  - by Grimlockz

  I need some advice about encrypt all traffic on a small private network running wi-fi and LAN traffic on 192.168.0.x network. The network would comprise of client laptops connecting to the wi-fi router (192.168.0.254) via ethernet connection or wireless. The main purpose of the server is for the client laptops to talk to two servers on different IP's (192.168.0.200 and 192.168.0.201) on ports 80 and 433. My main concern is having packet sniffers and what not getting access to the data. The only ways I see at the moment is to have VPN running on the network or use IPSec policy's to do this. Any other ways guys?

  Read the article

• Can dd-wrt or tomato keep track of GB usage per billing period per device?

  - by Sam Hasler

  I want to be able to track the usage of each device connecting to our router so we can split up the ISP bill by usage. Can dd-wrt or tomato provide the stats I'd need to do this? Update: After a bit of googling I'm aware of a much better answer than the current one. However I suspect there's probably more answers out there for other firmwares so in the interests of getting a more diverse set of answers—­and, I'll admit, because I'm getting tired of reading through obtuse firmware documentation—I've put up a bounty. If the only answer added is the one I've found I'll be happy to accept it for the bounty, otherwise I'll add it and accept it myself, but I'm hoping for an even better answer, or at least some options for other firmwares as from looking I've seen a few other people have asked for this and there doesn't appear to be a definitive answer, let's make this it! Go lazywebs! (Sorry. I've always wanted to say that.)

  Read the article

• Deprioritize BitTorrent traffic

  - by Steven Xu

  I'm sure the question has been asked before, but I can't seem to find it for myself; my Google-fu eludes me. My router, the Linksys E2000, does a decent job at being reasonable about prioritizing some sorts of traffic above BitTorrent traffic (there isn't too much interruption to port 80, 443, or 22 traffic, the ones I use most often). But other ports get pummeled. For instance, 3000 (which I use for local Rails testing) becomes almost entirely non-functioning. Xbox Live traffic (not sure about the ports, but they are in the 1000 range) doesn't do well either. So I'm wondering how to ensure that XBL and local Rails testing maintain strong service while BitTorrent is going. Is it enough that I turn up the QoS on their associated ports to high? It doesn't seem to be as effective as when BitTorrent isn't running at all (I don't know if there's a way to deprioritize BitTorrent traffic).

  Read the article

• iPhone always assigned wrong ip

  - by Ashley Ray

  for some reason most of the time my iPhone connects to the home network the ip address seems wrongly assigned as it 'loses connection' even even with strong reception. If I change the ip address to a static from 168.2.10 to 168.2.15 works fine until it appears to renew back to the prior. I am using a power-plug extender from the modem to router. Then have a laptop Printer playstation tv and another iPhone that always connect fine. The modem also has a crappy wireless which I haven't connected any devices to. I'm sure the forum will have a simple answer!

  Read the article

• What's wrong with my MAC address?

  - by Shaul

  I have a D-Link DSL-2650U router, and exactly one computer on the network. For reasons of port forwarding I want to give my computer a static internal IP address, so that I don't take the chance of losing my NAT settings every time the computer reboots. So here's a screen shot that summarizes the entire problem: WTH is wrong with my MAC address? It's copied and pasted from the command prompt window! I tried editing out the dashes, but it still doesn't work. Am I doing something wrong, or is there a bug in the D-Link firmware?

  Read the article

• 2nd/3rd version of wireless network appears

  - by neildeadman

  I replaced an old SpeedTouch ADSL router with a Netgear DG384 that I have and whilst doing so decided to change the wireless password. For this question assume my wireless network SSID is DeddersHome. On my netbook and macbook pro (running Win7) it won't connect to the Internet. When I hover over the tray icon for wireless it says "DeddersHome 2" and "DeddersHome 3" have no internet connection. What are these additional wireless networks? I can't see them in the wireless network list on any wireless device I have. Wired connections and wireless through my iPhone work fine. I saw this before with the SpeedTouch, but it just went away!! I also have one Apple AirPort Express connected to the wireless network which my Xbox is connected to (wired). This all worked before... I am going to remove AirPort to see if it is this causing the problem, but thought I'd ask the question to give it time for an answer whilst I continue to search. Cheers

  Read the article

• Ethernet 802.1x client -> WiFi AP on a Raspberry Pi?

  - by Martin Janiczek

  I have an Ethernet connection that requires 802.1x authentication (TTLS, MSCHAPv2, name+password). My goal is to connect that to something that would then act as an WiFi AP, so I can use the connection on more devices (iPhone, notebook, etc.) Would it be possible/good idea to use Raspberry Pi for this purpose? Or are there better-suited devices to do this? EDIT: found some alternatives but because of low rep can't post more than two links... OpenWRT + wpa_supplicant guide Carambola - works with OpenWRT (but probably not standalone?) Hornet-UB - works with OpenWRT Asus RT-N10+ + OpenWRT how-to EDIT 2: probably going to try TP-LINK TL-WR740N. It's a classic router, but can be flashed with OpenWRT, and the price beats everything else I've seen.

  Read the article

• Using a second wifi router as a wireless bridge

  - by Greg-J

  I purchased a D-Link DGL-4500 to replace my aging WRT54G around a year ago, only to find it nowhere near as reliable. It's been collecting dust since. I'm wondering if there is a way to use it as a wireless bridge so I can connect it to my home network and then use it's ethernet ports to provide network access to several devices. Is this something that can be done? If not, are there devices meant for this? Any help would be appreciated.

  Read the article

< Previous Page | 62 63 64 65 66 67 68 69 70 71 72 73  | Next Page >