Search Results

Search found 22968 results on 919 pages for 'stuck again'.

Page 663/919 | < Previous Page | 659 660 661 662 663 664 665 666 667 668 669 670  | Next Page >

• scan partition for bad blocks

  - by user22559

  Hello everyone I have a hard disk with bad sectors on it. I want to partition the drive so that the partitions are in the good part of the hard disk, and the parts that have bad sectors are not used. The first ~20GB of the hard disk are good. Then comes a ~13GB part that is riddled with bad sectors. After that, the hard disk is good again, but at the very end there is a ~2GB part with bad sectors. I have used an app called "Hdtune" to get this information, and I have created a 19GB c: partition at the beginning of the drive, then skipping the 13GB of bad sectors, then creating the D: partition that spans the rest of the disk, minus the last 2GB. The C: partition works well (i have been using it for a month and i have got no error whatsoever), but the D partition has been giving me problems. Somehow, it seems that I have some bad sectors in the D: partition. I am looking for an app that scans the HDD, finds the bad blocks, and shows them in a map so I can see if they are in the D partition. Or, an app that scans only a specified partition for bad sectors, and then shows in a map where the bad sectors are in the partition. I want to know this so I can resize the D partition so that it is outside of the bad area of the disk.

  Read the article

• I can't connect to my network, except in safe mode

  - by eidylon

  My laptop cannot connect to my network all of a sudden except in safe mode. When it boots, it will show the networks available in the tray popup, but if I click connect on any, it says "Unable to connect" and the troubleshooter is useless. Shortly thereafter all the networks disappear. I have tried removing IPv6 support as I have seen that cause problems. No joy. I've also tried removing the wireless network adapter in Device Manager and reinstalling it, also no joy. I've also tried attaching a USB wireless adapter, and it has the same problem. If I boot in safe mode, then it has no problems at all. Three other devices in the house connect fine, so I am pretty sure it is nothing to do with the router. Any ideas what to check next? I am running Win7 Ultimate on a 2GHz Quadcore with 8GB RAM with a Broadcom 802.11n wireless card. EDIT: RE wired connections: What is very weird is that if i plug in a wired connection, then not only does it connect via the wired connection, but the wireLESS also starts working perfectly. And a soon as I unplug the wire, then the wireLESS stops working again! So it seems the wireless is right now working only in safe-mode, or when a wired connection is also plugged in.

  Read the article

• CHKDSK is unable to fix NTFS errors

  - by HackToHell

  After my PC shutdown due to power failure, I noticed several errors in EventViewer. The file system structure on the disk is corrupt and unusable. Please run the chkdsk utility on the volume \Device\HarddiskVolume2. and The file system structure on the disk is corrupt and unusable. Please run the chkdsk utility on the volume C:. So I forced a chkdsk check at startup, and it finds a stream of error, here is the output, it is smaller than the actual log, because, Event Viewer only seems to have this much, the same line was repeated thousands of times.Here is that line. Some clusters occupied by attribute of type 0x80 and instance tag 0x4 in file 0x198f2 is already in use. Deleting corrupt attribute record (128, "") from file record segment 104690. Attribute record of type 0x80 and instance tag 0x0 is cross linked Also, even after running CHKDSK, the same errors were being reported again so I ran CHKDSK another time and it still loops the same line above, without fixing the error. Can anyone tell me how to fix it?

  Read the article

• Windows 7 - svchost high cpu usage.

  - by Leonardo

  Hey guys! I'm having a problem with windows 7 x64 i though it was slow and all then i saw that the cpu usage was always around 80% and started digging through google. there's two svchost consuming around 30% each and in the resources monitor there's a system interrupts consuming 45% all the time, i trid closing the aplications and makes no diference. so i tried some other things that i've found on gloogle like disable system update but didn't work. i'd love some help here. i don't know if it will help but here's my specs: Core 2 duo 4400 ATI radeon 4850 4gb ram DDR2 thanks anyway for your attention :) EDIT So i run the program and i got this info, did i get it right? EDIT As you asked here it is, did i get it right now? the other tcp/ip there's nothing. thanks again! :D EDIT I tried somthing here, i run msconfig and took the services that one of the svchost was using out of the startup and now my cpu is around 50%, but i still would like to make this better, i can't lose that much cpu power just because windows... thanks. EDIT yeah there's nothing i can do here, going to install xp for a while, it's really weird...

  Read the article

• Synchronizing files between Linux servers, through FTP

  - by Daniel Magliola

  I have the following configuration of servers: 1 central linux server, a VPS 8 satellite linux servers, "crappy shared hostings" I have a bunch of files that I need to have in all servers. Right now i'm copying them everywhere manually, but I want to be able to copy them to the central server, and then have a scheduled process that runs every now and then and synchronizes them (only outwardly, no need to try to find "new" files in the satellite servers). There are a couple of catches though: I can't have any custom software in the satellite servers, or do strange command line things that'll auto connect to them and send the files directly. I know this is the way these kinds of things are normally done, but the satellite servers are crappy shared hosting ones where I have absolutely no control over anything. I need to send the files over FTP I also need to have, in my central server, a list of the files that are available in each of the satellite servers, to make sure they are ready before I send traffic to them. If I were to do this manually, the steps would be: get the list of files in a satellite server compare to my own, and send the files that are missing get the list of files again, and store it in my central database. I'd like to know what tools are out there that can alleviate as much of this as possible, first the syncing, and then the "getting the list of files available in the other server". I'm going to be doing everything from PHP, not sure if there are good tools to "use FTP from PHP", which i'm pretty sure i'll have to do for step 3 at least. Thanks in advance for any ideas! Daniel

  Read the article

• Cannot open files in Visual Studio but in Delphi and Notepad

  - by Andrew J. Brehm

  About an hour ago Visual Studio 2008 decided that it cannot find files any more. This is on 64 bit Windows Vista. When I right-click on a text file (source code or otherwise) and select "open with" and "Visual Studio 2008", I get the following error (example): Windows cannot find 'C:\Users\ajbrehm\Documents\Visual Studio 2008\Projects\Hello Prism\Hello Prism\Main.pas'. Make sure you typed the name correctly, and then try again. When I right-click the same file and select "open with" and "Delphi 2010" or "Notepad" (both other options available for text files on my system), the file opens correctly. Oddly enough when the file is part of a Visual Studio project and I open the project itself with Visual Studio (this works), I can open the file from within Visual Studio. Any ideas what might be going on? This started about an hour after I made a complete backup of my Vista VM and after I installed IIS 7, SQL Express, and Sourcegear Vault. The first files I noticed couldn't be opened in Visual Studio any more where Pascal source files in checked-outed folders from Vault. And Vault also seems to be unable to see one of the sources files and claims they don't exist. I found out about Visual Studio not opening ANY files any more when I tried to recreate the file Vault refused to see. Update: I just checked. Another user, "administrator", can still open text files with Visual Studio 2008. Both users have administrator rights. Update: I just restored the hours-old backup. Same problem. Apparently whatever triggered this happened before the install of IIS 7 and SQL Express. Never noticed it before.

  Read the article

• No internet access when using static IP

  - by Endy Tjahjono

  I have just upgraded to Windows 8.1, and after the upgrade process is finished, I can't connect to internet. I tried running the "Troubleshoot problems": It concluded that DHCP needs to be activated: I let it activate DHCP, and I got internet connection back. The problem is I want to set this PC to a certain IP address (the IP address that it has been using all this time). I am also using Hyper-V, which I suspect has something to do with this problem. After I regained internet connection, I tried running one of my Hyper-V VM. From inside the VM I can connect to internet. That VM has static IP address. I also noticed that in "Control Panel\Network and Internet\Network Connections", I usually have a network connection called vEthernet (Realtek PCIe GBE Family Controller Virtual Switch). I didn't find it there after upgrade. How do I set my PC to a static IP while retaining internet access in Windows 8.1? EDIT I have managed to recreate vEthernet (Realtek PCIe GBE Family Controller Virtual Switch) by unchecking Allow management operating system to share this network adapter in Hyper-V's Virtual Switch Manager and then checking it again. But when I changed the adapter to use static IP, it still can't connect to internet. Result of Get-NetAdapter -Name * | fl (with MAC address removed): Name : vEthernet (Realtek PCIe GBE Family Controller Virtual Switch) InterfaceDescription : Hyper-V Virtual Ethernet Adapter #2 InterfaceIndex : 5 MacAddress : 55-55-55-55-55-55 MediaType : 802.3 PhysicalMediaType : Unspecified InterfaceOperationalStatus : Up AdminStatus : Up LinkSpeed(Mbps) : 100 MediaConnectionState : Connected ConnectorPresent : False DriverInformation : Driver Date 2006-06-21 Version 6.3.9600.16384 NDIS 6.40 Name : Ethernet 3 InterfaceDescription : Hyper-V Virtual Ethernet Adapter #3 InterfaceIndex : 6 MacAddress : 55-55-55-55-55-56 MediaType : 802.3 PhysicalMediaType : Unspecified InterfaceOperationalStatus : Up AdminStatus : Up LinkSpeed(Gbps) : 10 MediaConnectionState : Connected ConnectorPresent : False DriverInformation : Driver Date 2006-06-21 Version 6.3.9600.16384 NDIS 6.40 Name : Ethernet InterfaceDescription : Realtek PCIe GBE Family Controller InterfaceIndex : 2 MacAddress : 55-55-55-55-55-57 MediaType : 802.3 PhysicalMediaType : 802.3 InterfaceOperationalStatus : Up AdminStatus : Up LinkSpeed(Mbps) : 100 MediaConnectionState : Connected ConnectorPresent : True DriverInformation : Driver Date 2013-05-10 Version 8.1.510.2013 NDIS 6.30

  Read the article

• dhclient requests filling memory?

  - by shanethehat

  Dammit Jim, I'm a web developer, not a sys admin. With that out of the way, my client's has a CentOS server (6.2) that is only serving a single Magento site (and the associated MySQL server) and it is frequently running out of memory, despite the site only currently being open to 5 users. I'm investigating the logs to try to figure out why the memory usage is so high, but I don't really know what I'm looking at. It seems that there are a lot of entries in /var/log/messages concerning DHCP requests, approximately one every 15 seconds, that look like this: Apr 7 14:23:06 s15940039 dhclient[815]: DHCPREQUEST on eth0 to 172.30.102.85 port 67 (xid=0x6b5cd2a7) Is this normal? I don't see anything else in here that I don't recognise, but then I'm not sure I'd know the problem if I did see it. 4 days ago the server ran out of memory completely and locked up, requiring a restart. The DHCP messages did not start up again for 23 hours, but then carried on as before. I have read this question which describes the same issue, but in my case a fresh DHCP lease does not ever seem to be issued. Is this something I should push back to the hosting provider, or have I not yet found the source of the memory problem?

  Read the article

• Office 2007 constantly crashes, logged as Event ID 1000

  - by Nori

  I have a user, who despite my best efforts, is having constant Office 2007 crashes. I've tried deleting their profile and setting it up again, repairing office, uninstalling completely and then reinstalling, and swapping out memory sticks. One event log error I keep getting is the following: (note all the Office errors are event id 1000) Faulting application name: OUTLOOK.EXE, version: 12.0.6539.5000, time stamp: 0x4c12486d Faulting module name: EMSMDB32.DLL, version: 12.0.6539.5000, time stamp: 0x4c1246f8 Exception code: 0xc0000005 Fault offset: 0x0005d8e2 Faulting process id: 0xf6c Faulting application start time: 0x01cb6633f33384f3 Faulting application path: C:\Program Files (x86)\Microsoft Office\Office12\OUTLOOK.EXE Faulting module path: c:\progra~2\micros~1\office12\EMSMDB32.DLL Report Id: 0d4a2eab-d231-11df-80a0-4061868f5d10 I also get this: Faulting application name: OUTLOOK.EXE, version: 12.0.6539.5000, time stamp: 0x4c12486d Faulting module name: olmapi32.dll, version: 12.0.6538.5000, time stamp: 0x4bfc6ad9 Exception code: 0xc0000005 Fault offset: 0x002357a9 Faulting process id: 0x5e4 Faulting application start time: 0x01cb661f4546aa77 Faulting application path: C:\Program Files (x86)\Microsoft Office\Office12\OUTLOOK.EXE Faulting module path: c:\progra~2\micros~1\office12\olmapi32.dll Report Id: a4a90658-d224-11df-80a0-4061868f5d10 The Excel error is this: Faulting application name: EXCEL.EXE, version: 12.0.6535.5002, time stamp: 0x4bd2a7f1 Faulting module name: KERNELBASE.dll, version: 6.1.7600.16385, time stamp: 0x4a5bdbdf Exception code: 0xe06d7363 Fault offset: 0x0000b727 Faulting process id: 0x14a8 Faulting application start time: 0x01cb61ab7bc0abab Faulting application path: C:\Program Files (x86)\Microsoft Office\Office12\EXCEL.EXE Faulting module path: C:\Windows\syswow64\KERNELBASE.dll Report Id: ba0c454b-cd9e-11df-80a0-4061868f5d10 Also have gotten this for PowerPoint: Faulting application name: POWERPNT.EXE, version: 12.0.6500.5000, time stamp: 0x49a68f9d Faulting module name: COMShim.dll, version: 2010.3.325.110, time stamp: 0x4c51e0b1 Exception code: 0x40000015 Fault offset: 0x0001e388 Faulting process id: 0x1480 Faulting application start time: 0x01cb5fe9a0660e81 Faulting application path: C:\Program Files (x86)\Microsoft Office\Office12\POWERPNT.EXE Faulting module path: C:\Program Files (x86)\FactSet\COMShim.dll Report Id: e03d2a21-cbdc-11df-9bc8-4061868f5d10 (Some of the above lines edited to keep you from scroll horizontally.) Lastly, I get this error several times a day, I don't think it is related but maybe it is: Failed extract of third-party root list from auto update cab at: http://www.download.windowsupdate.com/msdownload/update/v3/static/trustedr/en/authrootstl.cab with error: A required certificate is not within its validity period when verifying against the current system clock or the timestamp in the signed file. Any ideas? This is driving me nuts.

  Read the article

• Windows PE network setup

  - by microchasm

  I'm walking through the following step-by-step guide for deploying Windows 7 via AIK: http://technet.microsoft.com/en-us/library/dd349348%28WS.10%29.aspx On step 4 (Capturing the Installation onto a Network Share), I run into a bit of a snag: attempting to connect to a network drive repeatedly fails. I'm using/deploying Dell Optiplex 380 64 bit machines, and the network cards seem to be really wonky. On the machine that I'm using to run AIK etc, the network driver wasn't found automatically. I had to manually go in and install the driver (which was found on the OEM installation media). I've since copied this to the USB key that I'm using for the Autounattend.xml so its handy. I think that because of this, the PE environment doesn't or can't instantiate the network device. Is there a way to install/configure the network device through the command prompt in PE? If not, I read about adding in the answer file path(s) to drivers, but if I did it this way, would I have to start the process all over again (i.e. create new Autounattend.xml with the PnPcustomizations path included, re-run the installation on the reference machine, install all the applications, re-make the PE iso, reboot into new PE iso)? Any shortcuts, direction, or advice would be appreciated. Thanks!

  Read the article

• MicroSD card isn't detected by computer, apparently usable only with phone

  - by paulcjoubert

  I have a 4GB MicroSD card that apparently only works (in the sense that the device detects and can read and write from and to the card) with my old Nokia XpressMusic 5800 phone. I have taken pictures and recorded voice notes that were saved on the card. These are accessible after the card has been removed, which tells me that the problem isn't with the card. The card could also not be locked to the phone as it would at least be detected by a computer and it would be able to write raw data to it with dd, such as /dev/zero. Also, the card is not the Nokia card that came with the phone and I have done nothing that would have caused it to be locked. (I could not find anything on Nokia's website that helps, but then again... my search was not THAT thorough.) The card works on no other device that I have tried so far. I have tried it in my Canon camera (through an adapter), but it refuses to even boot with the card inserted. My card reader (via USB cable and hub) is detected as /dev/sdx with or without the card inserted. When trying to access the card I get an "No medium found". dmesg does not report any change at all when inserting and removing the card. I would obviously like to use my card on other devices - the phone is quite old - and even a likely explanation would help. Thankyou in advance! EDIT 1: I can use the card by connecting the phone to my computer, but this is impractical and would not allow me to use the card in any other device. EDIT 2: The data on the card is not important to me at all.

  Read the article

• SSH client not showing prompt after successful login

  - by user431949

  I'm having problems with my SSH client on Ubuntu 10.10. When I switch on my computer and open a Terminal and execute the command ssh user@host, it gives me a password prompt after which I enter the right password, I then get a prompt to execute my commands on the remote computer. Now the problem is, after a little while (probably around 10 minutes), the terminal window stops accepting commands (No matter what I type, nothing shows). Once this happens, I close the Terminal window and try to start all over again by opening another Terminal window. But this time around, after entering the right password, I don't get a welcome message or prompt. The cursor just keeps blinking on a new line. I ran the ssh command with -v parameter and the message I get after a successful login is: debug1: Authentication succeeded (password). debug1: channel 0: new [client-session] debug1: Entering interactive session. debug1: Sending environment. debug1: Sending env LANG = en_GB.utf8 Still the cursor keeps blinking on a new line without a prompt. However, Putty SSH client works perfectly on the same machine. Thank you very much for your time. Your help would be greating appreciated.

  Read the article

• How to set up that specific domains are tunneled to another server

  - by Peter Smit

  I am working at an university as research assistant. Often I would like to connect from home to university resources over http or ssh, but they are blocked from outside access. Therefore, they have a front-end ssh server where we can ssh into and from there to other hosts. For http access they advise to set up an ssh tunnel like this ssh -L 1234:proxyserver.university.fi:8080 publicsshserver.university.fi and put the proxy settings of your browser to point to port 1234 All nice and working, but I would not like to let all my other internet traffic go over this proxy server, and everytime I want to connect to the university I have to do this steps again. What would I like: - Set up a ssh tunnel everytime I log in my computer. I have a certificate, so no passwords are needed - Have a way to redirect some wildcard-domains always through the ssh-server first. So that when I type intra.university.fi in my browser, transparently the request is going through the tunnel. Same when I want to ssh into another resource within the university Is this possible? For the http part I think I maybe should set up my own local transparent proxy to have this easily done. How about the ssh part?

  Read the article

• Media Center setup won't complete for watching TV

  - by Robert

  I have a problem watching TV in Media Center. The TV constantly pauses 1/2 second then plays 1 second, pauses 1/2 second, plays 1 second - it is constant and does not vary. This problem occurs on all channels, live or recorded. The bottom 5th of the screen is solid green. I know the problem is Media Center because I can use Pinnacle's TVCenterPro to watch TV and there is no skipping/pausing (and not green on bottom). I was using cable, and switched to DirecTV (satellite). Trying to do "Set up TV signal" in Media Center seems to be what broke it. I get an error "IR Hardware not detected." I can use the remote to "try again" - so the IR hardware works fine (Media Center's remote/sensor). I tried plugging the IR Blaster into both ports, and I tried a different USB port for the IR receiver. I can't complete the setup. Media Center was playing TV okay (with the new DirecTV) before I tried to run setup. (I ran setup to try to do recording with Media Center.) Hardware/Software: Pinnacle PCTV 800i HD PCI card (coax cable from DirecTV tuner), ATI Radeon HD 3200 Graphics, Windows XP SP3 Media Center Edition, AMD Athlon Dual Core 2.5 GHz, 1.75 GB RAM.

  Read the article

• Git clone/push/pull - where's that username comes from?

  - by Kuroki Kaze

  I've set up gitosis and able to pull/push through ssh. Gitosis is installed on Debian Lenny server, I'm using git from windows machine (msysgit). The strange thing, if I enable loglevel = DEBUG in gitosis.conf, I see something like this when doing any actions with gitosis server: D:\Kaze\source\test-project>git pull origin master DEBUG:gitosis.serve.main:Got command "git-upload-pack 'test_project.git'" DEBUG:gitosis.access.haveAccess:Access check for '[email protected]' as 'writable' on 'test_project.git'... DEBUG:gitosis.access.haveAccess:Stripping .git suffix from 'test_project.git', new value 'test_project' DEBUG:gitosis.group.getMembership:found '[email protected]' in 'test' DEBUG:gitosis.access.haveAccess:Access ok for '[email protected]' as 'writable' on 'test_project' DEBUG:gitosis.access.haveAccess:Using prefix 'repositories' for 'test_project' DEBUG:gitosis.serve.main:Serving git-upload-pack 'repositories/test_project.git' From 192.168.175.128:test_project * branch master -> FETCH_HEAD Already up-to-date. Question is: why am I *[email protected]? This email is in global user.email config variable, too. Yesterday, when the gitosis was installed, it seen me as kaze@KAZE, this is the name under which I was added to gitosis-admin group (and it worked). But today git (or gitosis) started to see me as [email protected]. This is true for all repositories I push or clone. I had to add this address to gitosis.conf directly on server to be able to edit configs again (it worked). There is 2 public keys in keydir: [email protected] and [email protected], their content is identical and they have kaze@KAZE at end. Origin URL looks like git@lennyserver:test_project. Now, the question is - why Git (or gitosis) suddenly decided to call me by email instead of name@machinename? I've changed a couple things trying to set up Gitosis (updated git on server to 1.6.0 for example), but maybe I broke something in my local git installation?

  Read the article

• Windows 2008 64bit: applications and explorer always hang

  - by Phil Farthing

  I setup a couple of Window 2008 64bit systems about 5 months ago. Initially all seemed well. Now however, for no apparent reason, things are dog slow, apps hang, explorer hangs, just clicking on something can cause a CPU spike of 100%, and often it's explorer that is eating it up. As I have two on identical hardware, and they experience the same problem, it doesn't seem related to addon software. The only thing these have in common is Kaspersky and I've tried disabling/uninstalling to no avail. There are no useful error messages in the event logs. Actually, the system never even reports app hangs. Sometimes, it similar to what I've seen on Windows 7 systems where the screen goes milky and asks if I want to trouble shoot, that's only when get impatient and click happy. The really odd thing, is that it will NOT do this for a few minutes at a time, and then starts up again. Like I will click on the start menu and browse for the Admin Tools, the start menu will hang at some point and I'll have to wait about a minute, then it's OK. The next time I do this, a few seconds later, it's fine. Every click seems to hang the first time around, then be ok the second time if I do the exact same thing. If anyone has any suggestions, please PLEASE let me know! thanks =)

  Read the article

• How to recover the plesk database?

  - by Kau-Boy

  When I try to launch the Plesk administration page of you server I get the following error: ERROR: PleskMainDBException MySQL query failed: MySQL server has gone away The MySQL Server is working well. Although it seems that the plesk database is somehow corrupt and any action on this database results in a restart of the mysql process, so even queries to other databases on the same MySQL server will be lost. If I try to connect to the plesk database using phpMyAdmin, I can only see the number of tables, the database had originally. But I am not able to open the tables listing. As soon as I try it, the mysql process crashes again. Trying to connect to the database using ssh works. I can even run a SELECT statement against any table an get a result. I don't know if it is an plesk error or an error of the psa database or even the MySQL server. Can you give me any tips on how to recover the plesk system. Should I try to repair the Plesk installation before. And if so, how can I do it and will all my settings get lost doing it? EDIT: Trying to dump the database, I get the following error: mysqldump: Got error: 2013: Lost connection to MySQL server during query when using LOCK TABLES

  Read the article

• It takes a long time until Windows XP recognize I connected USB drive

  - by Pavol G

  I have a problem with my new USB disk. When I connect it to my laptop with Windows XP SP2 it takes about 4-5min until Windows recognizes it and shows it as a new disk. I can also see (disk's LED is blinking) that something is scanning the disk when I connect it; when this is done Windows immediately recognize it. Also when I'm copying data to this disk the speed is about 3.5MB/sec. It's connected using USB2.0. I tried to check for spyware (using Spybot), also tried running Windows in safe mode. But still have the same problems. Do you have any idea what could help to solve this problem? On Windows Vista (another laptop) everything is ok, disk loads in about 15sec and speed is about 20-30MB/sec. Edit: I tried to update to SP3 - no change Edit2: When this "strange" scanning occurs I can see that DPCs process is taking about 50% of CPU. When the scan ends (after 5min) this process take 0% again. Edit3: About the scan time, currently it's taking about 5min, but this time is growing as I'm adding more data to the disk, currently its about 40GB and I don't want to see how long it will take with 1000GB. Thanks a lot for every advice!

  Read the article

• Domino nchronos.exe multiple instances causing server to die, and Sametime problems

  - by Kevin

  I've had this problem for a few months now. I thought it started when I installed the Traveller software on the server to add ActiveSync support, but I removed that and the problem still persists. Basically new instances of "nchronos.exe" keeps spawning (and not ending), so over a period of a few days the server eventually gets drowned in nchronos.exe processes, stops responding and I need to kill Domino. My process count the last time was up at about 330, and when I killed it and restarted the Domino my process count went to 160. I'm running Domino 8.5.1 with Fix Pack 2. I don't know if it's relevant, but my Domino server was also acting as a Sametime server. At around the same time that nchronos started playing up sametime also stopped working. None of my users can connect to sametime and in the domino log it keeps telling me "stpolicy.exe" has terminated. I've googled for that and tried a few things, but nothing seems to make sametime work again. Any thoughts?? Cheers, Kevin

  Read the article

• Windows 2003 R2 zip program blocking EXE file

  - by Harvey Kwok

  I have a Windows 2003 R2 Enterprise Edition SP2 32-bit machine with all latest patch (as of 1-6-2011). It's a VM. I have a zip file, including a pdf file, a txt file and a exe file. If I copy the zip file onto the machine via a shared network drive, I can unzip all the files properly without problems. If I put the zip file on my web server and then I download it from there, I can only unzip the pdf file and txt file. The exe file is silently ignored. I searched the web and found somebody reporting similar issue on XP. If I right click on the zip file downloaded from the web server, at the bottom of the general page, it has a warning message saying that "This file came from antoher computer and might be blocked to help protect this computer" I understand that I can solve the problem by simply clicking the "Unblock" button and extract the file again. The things that bothering me is that why the warning message says "might be blocked"? I tried downloading the same zip file from the same web server on to my Windows 7 box with latest patch. It also shows the same warning message. However, even with the warning message, I can extract all the files properly without clicking the "Unblock" button. Is it a bug in Windows 2003 R2 SP1? Is there any security settings controlling this? How likely will the end user seeing this problem? I want to dig into this because I am worrying people downloading my zip file from my web server might see similar problems. The first thought coming to the user's mind will be the zip file is somehow corrupted. Honestly, I didn't know this "Unblock" feature in Windows before I run into this problem. EDIT I just tried it on another Windows 2003 R2 SP1 machine. The zip program doesn't block the EXE file on that machine either. Both Windows 2003 R2 SP1 machines are joining to the same forest.

  Read the article

• How to install Red Hat Enterprise Linux on Apple Macbook Pro MacBookPro4,1

  - by Todd V. Rovito

  I have a one year old Mac Book Pro that I am trying to get RHEL 5.4 installed on via bootcamp. No matter what I do I can't get the installer to boot. I have tried multiple DVD's and even verified the install works on a new Mac Book Pro. Most of the time the installer simply locks up. I usually use Linux text with all-generic-ide on the boot line. I removed the ide parameter and I just used linux text. The results I get are that a bunch of kernel messages appear then the background turns blue and a thin text box pops up saying its loading ata..... something it disappears too fast for me to read. Then the machine freezes. I pressed the alt function keys to see if I could look at the system log, here is what it says: Alt-f3 says "trying to mount CD device hda" Alt-f4 says status error: hda: lastFailedSense Hda: Failed opcode was: unknown Hda: Lost interrupt Hda: Drive not ready for command Ide-cd: command 0x3 timed out Above this junk it looks like it found the partition because it knew it was 20 GB and listed as /dev/sda3. I think it has something to do with the CD drive, is that possible? Thanks again for the support. PS I posted in the apple support forums ( Apple.com Support Discussions Boot Camp Installation and Storage) and didn't get an answer.

  Read the article

• How can I wipe my iPod classic and fix any bad sectors on the hard drive without killing it?

  - by Sam Meldrum

  My iPod never finishes syncing and only syncs audio, not pictures or video - any ideas as to how I can fix it? My iPod classic 160GB worked well for a couple of years. I used to sync a lot of photos at full resolution to it, but this recently stopped working after I moved to Windows 7. iTunes is on latest version - 9.1.1.12 iPod software is up to date - 1.1.2 Windows 7 is fully up to date and patched The symptoms are that the iPod will start to sync, all audio (music and podcasts will sync successfully) but the syncing will then just appear to continue - itunes message: Syncing iPod. Do not Disconnect. This sync never completes - I have left it trying for days. I have tried resetting the iPod using the Restore button, whereupon it restarts sync from default options and again will sync audio, but nothing else. I suspect that something has gone wrong on the hard-drive - either a bad sector or some corrupt data. Is there a process I can go through to fix this? E.g. SpinRite or a format? If so how do I go about formatting an iPod and will it be recognised as an iPod after format and work as normal? Any advice on what to try next much appreciated? Update I have eliminated problems with the files, PC or iTunes as they sync fine to other iPods. I have also eliminated the cable by trying different cables which work with other iPods. What I'd really like to know is if there is any way to more fundamentally wipe the iPod safely, attempt to repair any bad sectors on the hard drive and then start from scratch. Anyone ever managed this?

  Read the article

• Dynamic subdomain routing

  - by Nader

  Hi everyone, I asked this question over at stackoverflow, but got very few views: http://stackoverflow.com/questions/2284917/route-web-requests-to-different-servers-based-on-subdomain Perhaps it's more applicable to this crowd. Here it is again for convenience: I have a platform where a user can create a new website using a subdomain. There will be thousands of these, eg abc.mydomain.com, def.mydomain.com . Hopefully if we are successful hundreds of thousands. I need to be able to route these domains to a different IPs to point at a particular app server. I have this mapping in a database right now. What are the best practices and recommended technologies here? I see a couple options: Have DNS setup with a wildcard CNAME entry so that all requests go to a single IP where perhaps two machines using heartbeat (for failover) know how to look up the IP in the database and then do an http redirect to the appropriate app server. This seems clunky and slow to me. Run my own DNS server that can be programatically managed such that when a new site is created a DNS entry is added. We also move sites around to different app servers, so I would need to be able to update DNS entries in close to real time. Thoughts anyone? Thanks. Update2: I've setup external wildcard DNS pointing at an HAProxy web server whose job it is to route requests to backend servers. The mapping is stored in our internal PowerDNS server. Question now is how to get the HAProxy server (or another) to use the value of the internal DNS and not some config file or access list? – Update: Based on some suggestions below, it seems like reverse-proxy server(s) is the way to go. As I'll be rebalancing the domain-server mapping, these need to work instantly and the TTL on a DNS solution could be a problem. Any recommendations on software to use considering this domain-IP data is stored in a DB, and I'll need this to be performant?

  Read the article

• Saving a file in a CSV type in Excel always removes the BOM

  - by rickp

  I've been trying to find a reasonable solution/explanation (unsuccessfully) to find out why Excel defaults to removing the BOM when saving a file to the CSV type. Please forgive me if you find this a duplicate of this question. This handles reading CSV files with non-ASCII encoding, but it doesn't cover saving the file back out (which is where the biggest issue lies). Here is my current situation (which I'm going to gather is common among localized software dealing with Unicode characters and a CSV format): We export data to a CSV format using UTF-16LE, ensuring the BOM is set (0xFFFE). We validate after the file is generated with a Hex editor to ensure it was set correctly. Open the file in Excel (for this example we're exporting Japanese characters) and witness that Excel handles loading the file with the correct encoding. Attempts to save this file will prompt you with a warning message indicating that the file may contain features that may not be compatible with Unicode encoding, but asks if you'd like to save anyway. If you select the Save As dialog, it will immediately ask you to save the file as "Unicode Text" rather than CSV. If you select the "CSV" extension and save the file it removes the BOM (obviously along with all the Japanese characters). Why would this happen? Is there a solution to this problem, or is this a known 'bug'/limitation of Excel? Additionally (as a side issue) it appears that Excel, when loading UTF-16LE encoded CSV files, only uses TAB delimiters. Again, is this another known 'bug'/limitation of Excel?

  Read the article

• Immediately tell which output was sent to stderr

  - by Clinton Blackmore

  When automating a task, it is sensible to test it first manually. It would be helpful, though, if any data going to stderr was immediately recognizeable as such, and distinguishable from the data going to stdout, and to have all the output together so it is obvious what the sequence of events is. One last touch that would be nice is if, at program exit, it printed its return code. All of these things would aid in automating. Yes, I can echo the return code when a program finishes, and yes, I can redirect stdout and stderr; what I'd really like it some shell, script, or easy-to-use redirector that shows stdout in black, shows stderr interleaved with it in red, and prints the exit code at the end. Is there such a beast? [If it matters, I'm using Bash 3.2 on Mac OS X]. Update: Sorry it has been months since I've looked at this. I've come up with a simple test script: #!/usr/bin/env python import sys print "this is stdout" print >> sys.stderr, "this is stderr" print "this is stdout again" In my testing (and probably due to the way things are buffered), rse and hilite display everything from stdout and then everything from stderr. The fifo method gets the order right but appears to colourize everything following the stderr line. ind complained about my stdin and stderr lines, and then put the output from stderr last. Most of these solutions are workable, as it is not atypical for only the last output to go to stderr, but still, it'd be nice to have something that worked slightly better.

  Read the article

< Previous Page | 659 660 661 662 663 664 665 666 667 668 669 670  | Next Page >