Search Results

Search found 18927 results on 758 pages for 'remote desktop'.

Page 668/758 | < Previous Page | 664 665 666 667 668 669 670 671 672 673 674 675  | Next Page >

• Video card not detected in POST on initial boot.

  - by Jeff M

  I have a minor problem with my desktop computer after cleaning it out for dust. When I first boot up the computer, the video card does not get detected so I can't see anything. In POST, I'm getting the "can't detect video card" beeps. The boot sequence continues normally, just without video. However, if I restart it (using the restart button) anytime after POST, it would boot up normally. I have no reason to think that the motherboard, video card or PSU got damaged in the process. It was working fine before, works fine after resetting. Took all the necessary precautions while cleaning. On the initial boot, I can hear the video card's fan power up but immediately power down and try again one more time only to fail. After the beep, resetting gets everything running and sounding normally. I've reseated the card a couple of times and reset the BIOS but doesn't seem to help. I'm hoping I won't have to take it out and remove and reinstall everything again. Does anyone recognize these symptoms to know exactly what the problem is? My guess is that the video card isn't getting enough juice initially to be running stable to be detected. I just don't know what I did (or didn't do) to get it to be in this state. It's not a high priority thing for me at the moment, just means I have to always reset it after initially turning it on but will eventually remove everything and reinstall if it comes to that. I don't think the specs are relevant here but just in case, here's the relevant stuff: Motherboard: Gigabyte P35-DS3P Video: EVGA GeForce 8600 GTS PSU: Antec True Power Trio 650W Built ~2 years ago, still running well

  Read the article

• Shortcut To Full Screen App In Lion

  - by omghai2u

  I postponed getting OSX Lion for as long as I possibly could. Now that I have it, I'm having lots of difficulties getting it to perform how I want. On Snow Leopard my typical setup for working was 4 spaces. I'd keep a Windows VM open on Space #4 full-screened, a Linux open on space #3, and I'd do other stuff on spaces #1 and #2. My keyboard shortcut allowed me to switch between my Windows work (Command + 4) to my Linux work (Command + 3) very quickly, and without the need for my hands to leave the keyboard (or effectively to even quit typing). Productivity was good. I see that on Lion a full-screened VM (and yes, they need to be full screened, Fusion's Unity won't cut it for what I need to do) is its own separate Desktop. I have set up 4 desktops and made my keyboard shortcuts to move between them Command + # just as before. But how do I get my full-screened VM to be one of those already existing desktops? Or, rather, how do I make a short-cut for the full-screened app?

  Read the article

• Offline productivity

  - by Frank Meulenaar

  On some days I'm commuting 2hs (oneway) in the train. I don't have any mobile internet nor is there always WiFi service in the train. Because of security reasons I can't do any work in the train so I'm trying to work on my geek time. I'm looking for general solutions on how to do this (I'm on FireFox/Windows but I don't think it matters) Email works perfectly with gmail offline. It syncs directly when online and remembers complicated stuff. So far I used the ScrapBook plugin to store an website. It works good, but I have to download my favorite news page every day again - I want it to sync as soon as possible. It would even be more awesome if I could click a page on my desktop and my laptop would sync as soon as it has the chance. (edit: maybe the autosave plugin for scrapbook can do this) Similarily, I use the Downloadhelper plugin to download youtube vids, but I'd like something that automatically downloads videos from a given channel. Any tips are welcome. So far my early morning schedule is: wake up, power on laptop, make coffee, power off laptop and leave within 10 minutes (enough time for GMail to sync) but I can imagine a system where my laptop stays on during the night (or boots before I wake (and makes me coffee :])).

  Read the article

• Create taskbar shortcut to website in Window 7

  - by BJ292

  I'd like to create a shortcut to a website in Windows 7 on the taskbar that is not pinned to the default web browser. Currently if I drag the favicon from the left end of the firefox address bar to the Win 7 taskbar it will pin a shortcut to the firefox browser icon. Similarly if I create a shortcut on the desktop to a website and drag it to the taskbar it will also end up pinned to the firefox icon. The problem with this is to get to that shortcut I have to right click on the firefox icon and then select the pinned shortcut. That is workable for me but I want to do this for a child - so the shortcut needs to be right there on the taskbar as a stand-alone item. There is a workaround that pretty much solves the problem - create a new folder somewhere safe - create the shortcut to the website in the new folder - right click the taskbar and select toolbars - new toolbar - then browse to the folder you created and select it as the new toolbar. The contents of the folder will now appear on the taskbar as shortcuts. You need to drag it from the right hand end of the taskbar into the middle - turn off show titles and show text and make the icon large. I'd call this a 75% solution. Anyone know how to make a web shortcut that looks and operates just like any of the other shortcuts on the taskbar?

  Read the article

• What's the mysql-5.5 compilation configuration arguments on Ubuntu 10.04?

  - by photon

  I want to install mysql 5.5 on my Ubuntu10.04 desktop system. But I'm not sure what arguments I should use after the cmake command. Though I've seen these articles: https://wikis.oracle.com/display/mysql/Cmake Building mysql-5.5.19 from source on ubuntu 11.10 with the static flag Compile MySQL 5.5.15 from source using autorun.sh and cmake, unable to start MySQL after Would anyone like to share the mysql-5.5 configuration arguments of compilation on Ubuntu 10.04? $cmake # what arguments to enter for this command update: cmake . -DBUILD_CONFIG=mysql_release -DCMAKE_INSTALL_PREFIX=/path/to/mysql_installation_dir -DWITH_SSL=no the official web site says it need to use cmake to compile the source package, but according to a teck blog, it doesn't need to compile the source, so which one is correct? When I use Cmake, I also had following error message: $ sudo cmake . -DBUILD_CONFIG=mysql_release -DCMAKE_INSTALL_PREFIX=/usr/local/mysql_community_5.5 -- The CXX compiler identification is unknown CMake Error: your CXX compiler: "CMAKE_CXX_COMPILER-NOTFOUND" was not found. Please set CMAKE_CXX_COMPILER to a valid compiler path or name. CMake Error at cmake/build_configurations/mysql_release.cmake:126 (MESSAGE): Clarification: I'm not clever and I'm a slow-thinking guy. And I cannot find a clever guy around me to give me some useful help. So I come here and hope someone is kind and generous enough to take the time to post the details.

  Read the article

• Clone a Windows Installation to a 3TB Hard Drive; MBR to GPT

  - by DanBlakemore

  I have Windows 7 Professional 64-bit installed on my desktop. Unfortunately for me and my wallet my hard drive is failing. I have purchased a 3TB hard drive as a replacement for my current 2TB drive. I would like to avoid as much hassle as possible in moving to this new drive so I would like to copy my current partition to the new drive using Gparted. The problem is that I suspect that my current partition is MBR, and I need GPT on my new drive since it is 3TB. Can I simply copy the MBR partition onto the new disk and then convert it to GPT after the fact (can you even convert the type of a partition)? Or would I need to somehow copy the contents of the partition into a GPT partition on the new drive? How do I go about making this transistion? Also, are there any issues I should be wary of booting to a GPT partition? If it matters, my motherboard is 1 year old as of May, 2012. Edit: My motherboard is 1 day old. My old one does not have UEFI compatibility, so I decided to make an upgrade to Intel today given that I would need a UEFI motherboard to use my new HDD. How much can I use a dying hard drive (bad sectors according to Hitachi Drive Fitness Test)? I have assumed not at all, to be safe.

  Read the article

• Gigabyte H55N-USB3: No video on HDMI

  - by newt

  I built a new PC with a Gigabyte H55N-USB3 / Intel Core i5 650. With a monitor plugged in the DVI port, everything works fine. I installed Windows 7 32-bit and enabled remote desktop connection. After that, I unplugged the monitor, plugged it into network and installed everything else (drivers, programs, etc) via RDP. However, when I try to use the HDMI port on my TV nothing appears. Neither during the boot, neither after Windows starts. The TV says there's "no signal" (if I remove the cable the message changes to "check cable"). The cable is new, and it is working fine with my home theater on same TV (by the way, it is the cable which came bundled with the home theater). Video driver is the latest from Intel site. Anyway, this shouldn't be the problem since there is no image during the boot. Any ideas or tips would be welcome. I'm googling around but found nothing useful, yet.

  Read the article

• What differences are there between "home" switches and "professional" switches?

  - by pjreddie

  Our radio station uses a PtP wireless system to stream our radio and TV signals from our studio up a hill to our transmitter. We have been having problems with warbly sound and drop outs that come from some point in this system. An engineer that occasionally visits the station thinks it could be the switches we use on each side of the PtP wireless system to connect the PtP devices to the encoders and decoders and wants us to get two of these switches: http://www.amazon.com/Netgear-JGS516-ProSafe-16-Port-Ethernet/dp/B0002CWPOK/ref=dp_return_1 The encoder/decoder setup only streams 8Mbps total so it seems like the switches we have should not be stressed out, unless they are causing sufficient latency to degrade the performance of the encoder/decoder. At each end of the connection we only have 4 connections, is there any reason we couldn't get a cheaper, "home" quality switch like this: http://www.amazon.com/D-Link-DGS-1005G-5-Port-Gigabit-Desktop/dp/tech-data/B003X7TRWE/ref=de_a_smtd Is there a significant difference that we would notice in terms of latency between these two switches? How much does the quality of the switch actually matter in this scenario? Any help is appreciated, feel free to ask questions if anything needs clarification. Thanks

  Read the article

• BackupExec 12 + RALUS - VERY slow backups

  - by LVDave

  We use Backup Exec 12 and the Remote Agent for Linux/Unix Servers (RALUS) to backup a large RHEL5 system. For various reasons we need to do a daily working set job. These working-set jobs run abysmally slow. The link between the target machine and the BE server is gigabit, and any other type of job runs 1-3GB/min. These working-set jobs start out at perhaps 40MB/min and over the course of the backup job slowly drops down so low that the BE job rate display in the "current jobs" goes blank.. Since we usually are only doing changed-files for one day, the job is usually small and finishes overnight and we don't worry abotu the slowness, but we had some issues with the backup server, and missed about 6 days of fairly heavy work on the Linux box, so this working-set job will be a doozy.. We have support with Symantec, and I've pestered them a lot about this, they've had me run RALUS in debug mode, sent them that log and a VXgather from the BE host and they had no fix/workaround.. To give an idea, I have the mentioned working-set job running for the last 3 1/2 hours and it's backed up just under 10MEGAbytes.... I'm posting this here to see if anybody in the "real world" has seen this/and/or has any ideas what might be causing these abysmally slow jobs, since Symantec seems to be clueless...

  Read the article

• Packet flooding while configuring a Debian L2TP/IPSec client?

  - by Joseph B.

  I'm currently at my wits end trying to configure an L2TP over IPSec VPN connection on my Debian using openswan and xl2tp box connecting to a server of unknown configuration. I've managed to successfully establish the connection and everything appears to be working well until I attempt to set the VPN connection as my default route, at which point I see a massive flood of packets simultaneously being transmitted (on the tune of ~1.5 GB in about 2min) until the server drops my connection. Prior to this network traffic on all my interfaces is minimal. According to iftop the majority of this traffic appears to be coming out of port 12, although I can't seem to figure out how to finger a specific process. If I instead just route traffic destined for 74.0.0.0/8 through it I'm able to access Google's servers through the VPN without issue. My xl2tp.conf file is: [lac vpn-nl] lns = example.vpn.com name = myusername pppoptfile = /etc/ppp/options.l2tpd.client My options.l2tpd.client file is: ipcp-accept-local ipcp-accept-remote refuse-eap require-mschap-v2 noccp noauth idle 1800 mtu 1410 mru 1410 usepeerdns lock name myusername password mypassword connect-delay 5000 And my routing table looks like: Destination Gateway Genmask Flags Metric Ref Use Iface 10.5.2.1 * 255.255.255.255 UH 0 0 0 ppp0 10.0.50.0 * 255.255.255.0 U 0 0 0 eth0 10.50.0.0 * 255.255.0.0 U 0 0 0 eth0 10.0.0.0 * 255.255.0.0 U 0 0 0 eth0 192.168.0.0 * 255.255.0.0 U 0 0 0 eth0 loopback * 255.0.0.0 U 0 0 0 lo default * 0.0.0.0 U 0 0 0 ppp0 I'm seeing absolutely nothing in auth.log and syslog during this time and can't seem to find any other log files it might be writing to. Any suggestions would be appreciated!

  Read the article

• Enabling http access on port 80 for centos 6.3 from console

  - by Hugo

  Have a centos 6.3 box running on Parallels and I'm trying to open port 80 to be accesible from outside tried the gui solution from this post and it works, but I need to get it done from a script. Tried to do this: sudo /sbin/iptables -A INPUT -p tcp -m state --state NEW -m tcp --dport 80 -j ACCEPT sudo /sbin/iptables-save sudo /sbin/service iptables restart This creates exactly the same iptables entries as the GUI tool except it does not work: $ telnet xx.xxx.xx.xx 80 Trying xx.xxx.xx.xx... telnet: connect to address xx.xxx.xx.xx: Connection refused telnet: Unable to connect to remote host UPDATE: $ netstat -ntlp (No info could be read for "-p": geteuid()=500 but you should be root.) Active Internet connections (only servers) Proto Recv-Q Send-Q Local Address Foreign Address State PID/Program name tcp 0 0 0.0.0.0:3306 0.0.0.0:* LISTEN - tcp 0 0 127.0.0.1:6379 0.0.0.0:* LISTEN - tcp 0 0 0.0.0.0:111 0.0.0.0:* LISTEN - tcp 0 0 0.0.0.0:80 0.0.0.0:* LISTEN - tcp 0 0 0.0.0.0:22 0.0.0.0:* LISTEN - tcp 0 0 127.0.0.1:631 0.0.0.0:* LISTEN - tcp 0 0 127.0.0.1:25 0.0.0.0:* LISTEN - tcp 0 0 0.0.0.0:37439 0.0.0.0:* LISTEN - tcp 0 0 :::111 :::* LISTEN - tcp 0 0 :::22 :::* LISTEN - tcp 0 0 ::1:631 :::* LISTEN - tcp 0 0 :::60472 :::* LISTEN - $ sudo cat /etc/sysconfig/iptables # Generated by iptables-save v1.4.7 on Wed Dec 12 18:04:25 2012 *filter :INPUT ACCEPT [0:0] :FORWARD ACCEPT [0:0] :OUTPUT ACCEPT [5:640] -A INPUT -m state --state RELATED,ESTABLISHED -j ACCEPT -A INPUT -p icmp -j ACCEPT -A INPUT -i lo -j ACCEPT -A INPUT -p tcp -m state --state NEW -m tcp --dport 22 -j ACCEPT -A INPUT -j REJECT --reject-with icmp-host-prohibited -A INPUT -p tcp -m state --state NEW -m tcp --dport 80 -j ACCEPT -A FORWARD -j REJECT --reject-with icmp-host-prohibited COMMIT # Completed on Wed Dec 12 18:04:25 2012

  Read the article

• daily rsync backups with hard links, checksums, and a new computer

  - by user75058

  I backup my laptop to a Fedora desktop daily using rsync with hard links. This has worked great for almost a year. I recently purchased a new computer, transferred over my data, and would like to continue backing up this computer daily. However, due to the data transfer from the old laptop to the new laptop, the timestamps have obviously changed, and will thus cause my daily rsync backup to re-transfer all of the data. I thought that by adding the -c (checksum) switch to my rsync backup it would match files based on checksum, instead of timestamp and size, and only transfer those files that are different or not present. This appeared to work, but upon examining the new backup, hard links are not being created, and it appears the files that should be hard linked are simply being copied to the new backup directory from the previous backup directory on the backup server. This is very peculiar behavior to me, and I am having trouble figuring out why this is occurring. Checksums match for files that I think should be hard linked. I have looked through the rsync man page and Google'd around a bit and have been unable to find anything for me to better understand this behavior.

  Read the article

• Trouble setting up incoming VPN in Microsoft SBS 2008 through a Cisco ASA 5505 appliance

  - by Nils

  I have replaced an aging firewall (custom setup using Linux) with a Cisco ASA 5505 appliance for our network. It's a very simple setup with around 10 workstations and a single Small Business Server 2008. Setting up incoming ports for SMTP, HTTPS, remote desktop etc. to the SBS went fine - they are working like they should. However, I have not succeeded in allowing incoming VPN connections. The clients trying to connect (running Windows 7) are stuck with the "Verifying username and password..." dialog before getting an error message 30 seconds later. We have a single external, static IP, so I cannot set up the VPN connection on another IP address. I have forwarded TCP port 1723 the same way as I did for SMTP and the others, by adding a static NAT route translating traffic from the SBS server on port 1723 to the outside interface. In addition, I set up an access rule allowing all GRE packets (src any, dst any). I have figured that I must somehow forward incoming GRE packets to the SBS server, but this is where I am stuck. I am using ADSM to configure the 5505 (not console). Any help is very much appreciated!

  Read the article

• How to detect/list rogue computers connected to a WIFI network without access to the Wifi Router interface? [migrated]

  - by JJarava

  This is what I believe to be an interesting challenge :) A relative (that leaves a bit too far to go there in person) is complaining that their WIFI/Internet network performance has gone down abysmally lately. She'd like to know if some of the neighbors are using her wifi network to access the internet but she's not too technically savvy. I know that the best way to prevent issues would be to change the Router password, but it's a bit of a PITA having to re-configure all wifi devices... and if the uninvited guest broke the password once, they can do it again... Her wifi router/internet connection is provided by the telco, and remotely managed so she can log-on to their telco account's page and remotely change the router's Wifi password, but doesn't have access to the router status page/config/etc unless she opts out of the telco's remote support and mainteinance service... So, how could she check if there are guests in the wifi with this restrictions and in the most "point and click way"? In this case I'd probably use nmap to look for other devices in the network, but I'm not sure if that's the easiest way to do it. I'm not a wifi expert, so I don't know if there are any wifi-scanning utils that can tell us who's talking to the router... Lastly, she's a Windows user as I guess that'll influence the choice of tools available Any suggestions more than welcome Regards!

  Read the article

• Sharing music on NAS with Zune and iPod?

  - by osij2is

  After being a long time iPod owner, I'm switching to the new Zune with its subscription model. I haven't bought a Zune yet but I'm planning on doing so within the next month or so. I have approximately 40GB worth of music and my girlfriend has her iPod music library around 30GB. I've been trying to figure out how to migrate all our music off of our laptops/desktops and centralize everything on my NAS. In sharing iPod music isn't too bad. Sharing from one machine to all is fairly easy within the iTunes player. As far as storing all the music on a NAS, again, iPods aren't too bad and imagine other systems aren't difficult. But I'm really new to the Zune and I'm beginning to run into some issues. My questions are: Is it possible to store all music from our iPods and Zune subscriptions and share music between the iPod/Zune within the same file share on my NAS? I'm sure it's possible to store music on a share, but I'm not sure how iTunes and the Zune software differs. Is there 3rd party software, maybe something like DoubleTwist that can sync based from NAS to multiple desktop/laptops? I've never used DoubleTwist but it's something that I found that looks close to being what I need. I've never quite done this myself so I'm trying to find a solution that can: a) store music on a network share; b) sync between different devices (Zune/iPod) seamlessly.

  Read the article

• Mac OS X - Time Machine backup fails verification - What can I do to save the history?

  - by usermac75

  Hi, How do I make Time Machine to make a new complete backup without losing older versions of backed up files? Verbose: I am using the Time Machine backup on my OS X (Snow Leopard) to backup the whole computer to an external drive. I especially like the "history", i.e. the feature that allows you to restore the older version of a file. Problem: I had some data corruption on my external backup drive, I repaired it with the System Tool for doing that, it found some faults. I had the disk tool repair the external drive. After that, the external drive was OK and I could use Time Machine again. I let Time Machine do one more backup. Now I made a verification according to http://superuser.com/questions/47628/verifying-time-machine-backups, namely along sudo diff -qr . $HOME/Desktop 2>&1 | tee $HOME/timemachine-diff.log However: After doing the command above, several differences and missing files were reported, approx. 200 files in sum. Whereas some of the missing files were cache or excluded directories, the differences do bother me, especially as some important documents from me are listed as differing. How can I make sure that the data on the external drive is synced correctly? Is it possible to have Time Machine to do a complete new backup without losing the history? Or to have Time Machine compare all files for differences and re-write all files that are different? Or can I set some flags on the files that do not match to have them copied again? (like the archive-flag in Windows/Dos). I'd rather not touch the files because I would like to keep the date of last change/date of creation) Thank you for your thoughts!

  Read the article

• Suggestions for Backup solution

  - by jiewmeng

  i am considering between windows home server simple nas extra HDD's in desktop btw, i will be the main user i am looking to fulfil the following needs: reliability (i am think RAID 1 or 5) not so prone to virus/malware infections (will using a separate NAS or home server help? say windows home server is still a windows pc except separated by network?) power efficiency (eg. spin down when not in use) download (eg. i may want to dl big files/torrents overnight and i may not want to use a full powered PC for it? does a full pc vs NAS provide significant power usage to justify cost of new system esp. since i am only user?) performance (i guess i like to write/access my files fast, on 2nd thought, maybe for backup i can forgo this? maybe for a WD Green HDD? but how much slower will it be? plus since i am the only user, i think the whole HDD will be mine?)

  Read the article

• AA doesn't work due to monitor?

  - by MikeQ

  I have a monitor (with TV tuner - Philips 221T1SB), native resolution of 1920x1080, but there is an Overscan in Catalyst. It says from left to right '10%' and '0%', if i set it (all the way to the left) on 10%, i get screen with black borders (you know what i mean), but if i set it to 0%, i get a filled monitor. It does make sense, but why the hell is there such an option? I never had any AA issues before, but now, with this monitor, here they go. I can't find any solution, i have only one lead = overscan, or pretty much anything with the CCC settings. Yes, i almost forgot. After a bit of trying to configure the monitor with remote, i found there is a PC channel option, few other channels, and then a HDMI option. I have monitor through HDMI, but why i get black screen when i select the PC channel? That might be another problem. I tried almost everything. Please guys, give me a hand. I don't want jaggies! CPU: Intel I5-750 @4,0GHz RAM: Corsair Vengeance 8GB 1600MHz GPU: AMD Gigabyte HD 7950 Windforce @1100/1400, 1,174V Motherboard: ASUS P7P55D-E EVO

  Read the article

• How do I change the default ftp folder in MacOS X 10.6?

  - by Wild_Eep

  I'm running WordPress 2.9.1 from a Mac running 10.6.3. WordPress is installed to the /Library/WebServer/Documents folder. WordPress has a feature called AutoUpdate. Clicking an autoupdate button will download and install updated versions of the WordPress software, or third-party plugin tools. It's a convenient way to keep things up to date. WordPress uses FTP to download the files. I've enabled FTP and set up a user account and opened the requisite ports in my firewall for FTP traffic. This doesn't seem to be enough for my self-hosted installation, though. I'm sure this feature was originally designed for someone who has access to a remote shared webserver, and that it's merely a configuration challenge related to the FTP setup. I feel that if I can adjust the initial directory that the FTP service presents to the AutoUpdate feature, everything else will work properly. So, my question is, how do I adjust what folder is presented when a given user connects to a Mac running 10.6.3 via FTP?

  Read the article

• Is it possible to record a screen-video from a VNC server?

  - by nikie

  I have a computer that's running VNC server. I would like to record a video of what's going on on this computer, if possible without installing additional software on that computer. Is there a program that can connect to the VNC server port and instead of displaying the screen save it to an (e.g. AVI) video file? Background: One of our customers sometimes has problems with the software he bought from us when he's performing a complex procedure. To help him, we offered that someone (a service technician or programmer) watches what he's doing during that procedure to find out if he's doing something wrong or if there's a bug in the software. Currently, this is done live via VNC. That has a few disadvantages: The service technician has to be in the office at the time. As the customers are in different time zones, that can be in the middle of the night. If the service technician forgets something or doesn't notice something, it's lost. There's no way to see what happened again. Only a single computer can be watched by one service technician at a time. I know I could install normal screen-grab software on the computer, but we're talking about an embedded system with limited RAM, CPU, HDD space, so installing something new is not an easy decision. And VNC is already there. I could of course open a VNC client on some office PC and capture that PC's screen, but I can only record one remote computer that way. I often have to watch up to 8 screens in parallel. (And I don't think that screen-grabbing VNC would improve image quality, either.)

  Read the article

• How do I setup a proper VPN for my friends to play LAN games AND give them internet access?

  - by Gizmo

  I'm trying to setup a VPN on my local network, but everyone who connects to me DOES have access to my laptop but not to the internet or other devices on the network. How can I properly configure my VPN on windows to work correctly (giving internet + access to all devices on my network to the remote pc)? Or is there software on windows which makes creating a VPN server easier? or maybe a VMWare image linux vpn server? I can't find any of those! My requirement is that my friends don't have to install additional software, they have to be able to connect with default windows stuff. My OS is Windows 8 Standart edition (not pro or enterprise) OEM. Most of my friends have also windows 8, some windows 7. Extra info: My device is DMZ'ed (Demilitarized Zone, [disabled NAT on my device so it's accessible on the WAN]) I can access files, websites and services on other devices on my network, and all devices can access file shares, website and all other services on my device When enabling VPN everything works except the client is unable to get internet access or access to any device on my network, client has only access to my device.

  Read the article

• Windows network routing

  - by fabianvilers

  Hi! I'm working by my customer premises and they let me connect my private laptop on a dedicated Wi-Fi for internet access. It's nice for external consultants. The only issue is that we can't connect on a remote server on port 25. I suppose this policy is set up to avoid infected computers sending spam from their network. As you can have guessed, this is something weird that I can't send mail at all. Fortunately, I've a 3G cell phone that I can connect by Bluetooth on my laptop. So when I want to send an e-mail, I have to disconnect from Wi-Fi, connect my phone, send the e-mail, disconnect phone and reconnect Wi-Fi. Kinda overhead. My question is: how can I tell Windows 7 to use the Wi-Fi for every out connection, but if it's a connection on port 25, use the cell phone network? With this solution, I could let my phone connected all day without having to switch again and again. Thanks a lot for your anwwers. Fabian

  Read the article

• Route web browsing through a separate iterface

  - by tkane

  I'd like to route web browsing through the wlan0 interface and the rest through eth1. Can you please help me with the iptables commands to achieve this. Below is my configuration. Thank you :) Edit: This is about desktop configuration not a web server set up. Basically I want to use one of my connections to browse the web and the other one for everything else. ifconfig: eth1 Link encap:Ethernet HWaddr 00:1d:09:59:80:70 inet addr:192.168.2.164 Bcast:192.168.2.255 Mask:255.255.255.0 inet6 addr: fe80::21d:9ff:fe59:8070/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:33 errors:0 dropped:0 overruns:0 frame:0 TX packets:41 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:4771 (4.7 KB) TX bytes:7081 (7.0 KB) Interrupt:17 wlan0 Link encap:Ethernet HWaddr 00:1c:bf:90:8a:6d inet addr:192.168.1.70 Bcast:192.168.1.255 Mask:255.255.255.0 inet6 addr: fe80::21c:bfff:fe90:8a6d/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:77 errors:0 dropped:0 overruns:0 frame:0 TX packets:102 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:14256 (14.2 KB) TX bytes:14764 (14.7 KB) route: Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 192.168.2.0 * 255.255.255.0 U 1 0 0 eth1 192.168.1.0 * 255.255.255.0 U 2 0 0 wlan0 link-local * 255.255.0.0 U 1000 0 0 wlan0 default adsl 0.0.0.0 UG 0 0 0 eth1

  Read the article

• Hyper-v and sql server connections for web apps

  - by Rick Ratayczak

  I have a physical machine running win8, and two VMs in hyper-v client: 1 web server, 1 sql server. The web server works fantastic. The sql is the one that is giving me the problem. I can connect to it with server explorer in visual studio or management studio just fine, and it's blazing fast. The problem happens when I use the same connection string I am using in visual studio server explorer in the web.config for an app. data source=VMSQL1;initial catalog=OtherShell;persist security info=True;user id=OtherShell;password=****;network library=dbmssocn;MultipleActiveResultSets=True;App=EntityFramework I made sure it was also using tcp-ip, but it doesn't connect with or without the network library part of the connection string. A network-related or instance-specific error occurred while establishing a connection to SQL Server. The server was not found or was not accessible. Verify that the instance name is correct and that SQL Server is configured to allow remote connections. (provider: SQL Network Interfaces, error: 26 - Error Locating Server/Instance Specified) This is driving my batty for the last two days, any ideas? It fails from the web vm too, but works in management studio with the same connection string.

  Read the article

• Half of installed RAM is hardware reserved

  - by user968270

  After a rather arduous and convoluted series of problems that left me without a desktop for ~80 days, I've finally got the thing up and running, having replaced the power supply, motherboard, graphics card and CPU. Now, however, I'm experiencing the 'hardware reserved RAM' issue. Perhaps this is the exhaustion talking, but looking at the question that tends to get pointed to when this kind of topic gets locked as a duplicate hasn't helped. I have 16 GB of RAM installed in an MSi 970A-G46, which is spec'd for up to 32 GB of RAM. The BIOS recognizes that I have 16 GB installed, and the resource monitor also shows the whole 16 GB, only it shows 8 GB as hardware reserved. I've seen suggestions that it's an OS issue, but the particular installation of Windows 7 (64-bit) which I'm running on my boot drive is the same as the one that could actually access the 16 GB in my previous motherboard (MSi 870A-G54). I've updated my BIOS using the MSi Live Update tool and restarted the machine with no effect, and I cannot seem to locate any 'Memory Remapping' option as I've seen mentioned. I've physically swapped the RAM between the slots to no effect. I've unchecked the Maximum Memory box in the msconfig Boot tab's advanced options, also to no effect. These are my system's basic specifications OS: Windows 7 Home Premium (64-Bit) Motherboard: MSi 970A-G46 CPU: AMD FX-8150 Graphics Card: XFX Radeon HD 6870 Boot Drive: OCZ Agility 3 Storage Drive: Samsung Spinpoint F3 ST1000DM005/HD103SJ 1TB PSU: Thermaltake TR-2 TR600 600W ATX12V v2.3

  Read the article

< Previous Page | 664 665 666 667 668 669 670 671 672 673 674 675  | Next Page >